Search Results (27,743)

This study investigates the corrosion resistance of chitosan and its crosslinked form coatings applied on stainless steel as substrate using various analytical techniques. Fourier transform infrared spectroscopy (FTIR-ATR), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were employed for surface characterization. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization (PDP) techniques were used to analyze the electrochemical behavior. Four coatings were evaluated along with naked stainless steel (ss): chitosan (Chi), chitosan crosslinked with ammonium paratungstate (Chi/PTA), chitosan crosslinked with polyethylene glycol (Chi/PEG), and chitosan crosslinked with polyvinylpyrrolidone (Chi/PVP). Electrochemical measurement parameters analysis assessed the coating corrosion resistance, such as impedance modulus (|Z|) and corrosion potential (Ecorr). Results indicate varying degrees of corrosion resistance among the coatings. Chi/PTA exhibited notable characteristics in the electrochemical tests, showing promising polarization resistance (Rp) and impedance behavior trends. Conversely, Chi/PEG showed differing electrochemical responses, suggesting higher susceptibility to corrosion under the study conditions. These findings contribute to understanding the electrochemical performance of chitosan-based coatings on stainless steel, highlighting their potential in corrosion protection applications. Full article

The present study focused on demonstrating the versatility of the slurry deposition technique to produce aluminide coatings to protect components from high-temperature corrosion in a broad temperature range, from 400 to 1400 °C. This is a simpler and low-cost coating technology used as an alternative to CVD and pack cementation, which also allows the coating of complex geometries and offers improved and simple repairability for a lot of industrial applications, along with avoiding the use of non-hazardous components. Slurry aluminide coatings from a proprietary water-based-Cr6+ free slurry were produced onto four different substrates: A516 carbon steel, 310H AC austenitic steel, Ti6246 Ti-based alloy and TZM, a Mo-based alloy. The resulting coatings were thoroughly characterised by FESEM and XRD, mainly so that the identification of microstructures and appropriate phases was reported for each coating. The importance of surface preparation and heat treatment as key parameters for the coating final microstructures was also evidenced, and how those parameters can be optimised to obtain stable intermetallic phases rich in Al to sustain the formation of a protective Al₂O₃ oxide scale. These coating systems have applications in diverse industrial environments in which high-temperature corrosion limits the lifetime of the components. Full article

Here, we highlight the research presented in this Special Issue, focusing on the innovative use of graphene and other two-dimensional (2D) materials to develop advanced coating technologies. The contributions herein address critical challenges such as the scalable fabrication and stable dispersion of such materials and their compatibility with conventional coating systems, offering solutions that enhance their mechanical strength, chemical stability, and multifunctionality. The featured studies demonstrate the diverse applications of these materials, from protective anticorrosive barriers to high-performance optoelectronic devices and environmental remediation. Moving forward, future research is encouraged to explore novel 2D materials, hybrid coating strategies, and advanced computational modeling to overcome existing limitations and unlock new possibilities. Full article

Iron microparticles were coated with polypyrrole in situ during the chemical oxidation of pyrrole with ammonium peroxydisulfate in aqueous medium. A series of hybrid organic/inorganic core–shell materials were prepared with 30–76 wt% iron content. Polypyrrole coating was revealed by scanning electron microscopy, and its molecular structure and completeness were proved by FTIR and Raman spectroscopies. The composites of polypyrrole/carbonyl iron were obtained as powders and characterized with respect to their electrical properties. Their resistivity was monitored by the four-point van der Pauw method under 0.01–10 MPa pressure. In an apparent paradox, the resistivity of composites increased from the units Ω cm for neat polypyrrole to thousands Ω cm for the highest iron content despite the high conductivity of iron. This means that composite conductivity is controlled by the electrical properties of the polypyrrole matrix. The change of sample size during the compression was also recorded and provides a parameter reflecting the mechanical properties of composites. In addition to conductivity, the composites displayed magnetic properties afforded by the presence of iron. The study also illustrates the feasibility of the polypyrrole coating on macroscopic objects, demonstrated by an iron nail, and offers potential application in the corrosion protection of iron. The differences in the morphology of micro- and macroscopic polypyrrole objects are described. Full article

One of the latest trends in sustainable agriculture is the use of beneficial microorganisms to stimulate plant growth and biologically control phytopathogens. Bacillus subtilis, a Gram-positive soil bacterium, is recognized for its valuable properties in various biotechnological and agricultural applications. This study presents, for the first time, the successful encapsulation of B. subtilis within electrospun poly(3-hydroxybutyrate) (PHB) fibers, which are dip-coated with cellulose derivatives. In that way, the obtained fibrous biohybrid materials actively ensure the viability of the encapsulated biocontrol agent during storage and promote its normal growth when exposed to moisture. Aqueous solutions of the cellulose derivatives—sodium carboxymethyl cellulose and 2-hydroxyethyl cellulose, were used to dip-coat the electrospun PHB fibers. The study examined the effects of the type and molecular weight of these cellulose derivatives on film formation, mechanical properties, bacterial encapsulation, and growth. Scanning electron microscopy (SEM) was utilized to observe the morphology of the biohybrid materials and the encapsulated B. subtilis. Additionally, ATR-FTIR spectroscopy confirmed the surface chemical composition of the biohybrid materials and verified the successful coating of PHB fibers. Mechanical testing revealed that the coating enhanced the mechanical properties of the fibrous materials and depends on the molecular weight of the used cellulose derivatives. Viability tests demonstrated that the encapsulated B. subtilis exhibited normal growth from the prepared materials. These findings suggest that the developed fibrous biohybrid materials hold significant promise as biocontrol formulations for plant protection and growth promotion in sustainable agriculture. Full article

LSPwC is an important development of Laser shock peening (LSP) technology, and surface texturing is an effective method to improve tribological properties. The combination of these is expected to innovate a new surface texturing technology with a strengthing effect, but no one has attempted it. In this paper, a new LSPTwC technology combining them is innovatively proposed and validated on AISI 9310 steel, which is commonly used in helicopter transmission components for surface texturing. The LSPTwC surface was studied using an optical microscope, electron microscope, energy dispersive spectrometer, and so on. The results proved that LSPTwC is an effective texturing method of AISI 9310 steel, which modulates the texture and improves the properties, such as the microhardness increased by more than 10%. A model for calculating the texture and process parameters is also constructed on a statistical basis, and a modeling method for textured surfaces is proposed. It is verified that the calculation results and the constructed model are highly consistent with the test, with a diameter deviation <3% and depth deviation <4%. The above results can provide the experimental basis, process design method, and calculation model for single-point LSPwC texturing of AISI 9310 steel parts for helicopters, which have application value. Full article

In this paper, the humidity-sensing characteristics of gelatin were compared with those of poly(vinyl alcohol) (PVA) at L-band (1 ~ 2 GHz) microwave frequencies. A capacitive microwave sensor based on a defected ground structure with a modified interdigital capacitor (DGS-MIDC) in a microstrip transmission line operating at 1.5 GHz without any coating was used. Gelatin is a natural polymer based on protein sourced from animal collagen, whereas PVA is a high-sensitivity hydrophilic polymer that is widely used for humidity sensors and has a good film-forming property. Two DGS-MIDC-based microwave sensors coated with type A gelatin and PVA, respectively, with a thickness of 0.02 mm were fabricated. The percent relative frequency shift (PRFS) and percent relative magnitude shift (PRMS) based on the changes in the resonant frequency and magnitude level of the transmission coefficient for the microwave sensor were used to compare the humidity-sensing characteristics. The relative humidity (RH) was varied from 50% to 80% with a step of 10% at a fixed temperature of around 25 °C using a low-reflective temperature and humidity chamber manufactured with Styrofoam. The experiment’s results show that the capacitive humidity sensitivity of the gelatin-coated microwave sensor in terms of the PRFS and PRMS was higher compared to that of the PVA-coated one. In particular, the sensitivity of the gelatin-coated microwave sensor at a low RH from 50% to 60% was much greater compared to that of the PVA-coated one. In addition, the relative permittivity of the fabricated microwave sensors coated with PVA and gelatin was extracted by using the measured PRFS and the equation was derived by curve-fitting the simulated results. The change in the extracted relative permittivity for the gelatin-coated microwave sensor was larger than that of the PVA-coated one for varying the RH. Full article

The operational efficiency, stability, and lifespan of hydroelectric power plants operating on sediment-laden rivers are affected by sediment erosion. A numerical simulation of the sand–water flow in the water-intake components of a turbine at a specific power station was conducted using the Euler–Lagrange method. Additionally, sediment erosion tests were carried out on the water-intake components coated with epoxy mortar material. The results indicate that sediment erosion on the stay vane surface mainly occurs on the front face, with the most severe erosion at the head, while sediment erosion on the stay ring surface primarily occurs near the stay vane head. The extent of erosion is mainly influenced by the distribution characteristics of sediment particles. The wear of epoxy mortar coating material is minimally affected by the spraying thickness. Adding 30% hardener to the epoxy mortar material can significantly improve the erosion resistance of the stay vane surface by about 30%. The erosion rate on the frontside of the stay vane is approximately 2.6 times that of the backside. Based on the sediment erosion tests and numerical simulation results of the sand–water flow, an estimation formula for the sediment erosion rate of the epoxy mortar erosion-resistant coating was established. This formula can be used to predict the anti-sediment erosion performance of epoxy mortar materials applied to the water-intake components of this turbine and similar river turbines. Full article

Gelatin is a promising biopolymer for edible coatings thanks to its low cost and gelling properties. However, its weak mechanical properties limit its use. This study aimed to develop a gelatin coating with tomato extract, analyzing its antioxidant activity and rheological properties for food applications. Gelatin concentrations (2, 5, and 7%) were evaluated, and it was determined that 7% with 7.5% glycerol was the optimal mixture. Three concentrations of tomato extract (0.5, 1, and 1.5%) were added, and antioxidant activity was evaluated using the ABTS technique, as well as the interaction of components through FT-IR and physicochemical analysis. The results showed that there were no significant differences in terms of their physicochemical characterization, maintaining a pH of 5 and a yellowish hue. The FT-IR spectra indicated there were hydrogen bond interactions between gelatin and the extract. The antioxidant capacity was higher with the 1.5% extract, achieving an inhibition of 58.9%. It was found that the combination of the different materials used improved the rheological (specifically the viscosity and stability of the material) and antioxidant properties of the gelatin. These findings suggest that modified gelatin coatings may be effective in extending the shelf life of foods. Full article

Intumescent fireproof coatings protect steel structures and cables by forming a thick, fire-resistant layer under high temperatures. These coatings can deteriorate over time, impacting their fire resistance. Current testing methods are largely lab-based, lacking in-service evaluation platforms. Laser-Induced Breakdown Spectroscopy (LIBS) is emerging as a promising in situ detection technology but is influenced by low air pressure in high-altitude areas. This study investigates how air pressure affects LIBS signals in intumescent coatings on galvanized steel. Using pressures between 35 and 101 kPa, a linear model was developed to correlate laser pulses to ablation depth for characterizing coating thickness. Results show that spectral intensity decreases with lower air pressure. However, a strong linear relationship persists between laser pulses and ablation depth, with a fitting accuracy above 0.9. The coating thickness is identified by the number of laser pulses required to detect the Zn spectral line from the underlying galvanized steel. As air pressure decreases, the ablation depth increases. The study effectively models and corrects for air pressure effects on LIBS data, enabling its application for field detection of fireproof coatings. This advancement enhances the reliability of LIBS technology in assessing the fire performance of these materials, providing a reference for their in situ evaluation and ensuring better fire safety standards for building steel structures and cables. Full article

The skin, recognized as the largest organ in the human body, serves a vital function in safeguarding against external threats. Severe damage to the skin can pose significant risks to human health. There is an urgent requirement for safe and effective therapies for wound healing. While phytotherapy has been widely utilized for various health conditions, the potential of Quercus glauca in promoting wound healing has not been thoroughly explored. Q. glauca is a cultivated crop known for its abundance of bioactive compounds. This study examined the wound-healing properties of Quercus glauca acorn seed coat water extract (QGASE). The findings from the study suggest that QGASE promotes wound closure in HF cells by upregulating essential markers related to the wound-healing process. Additionally, QGASE demonstrates antioxidant effects, mitigating oxidative stress and aiding in recovery from injuries induced by H₂O₂. In vivo experiments provide additional substantiation supporting the efficacy of QGASE in enhancing wound healing. The collective results indicate that QGASE may be a promising candidate for the development of innovative therapeutic strategies aimed at enhancing skin wound repair. Full article

Biospecimen imaging is essential across various fields. In particular, a considerable amount of research has focused on developing pretreatment techniques, ranging from freeze-drying to the use of highly conductive polymers, and on advancements in instrumentation, such as cryogenic electron microscopy. These specialized techniques and equipment have facilitated nanoscale and microscale bioimaging. However, user access to these environments remains limited. This study introduced a novel technique to achieve high conductivity in bioimaging by employing a magnetically controlled sputtering cathode to facilitate low-temperature deposition and low-electron bombardment. This approach allows for the convenient high-magnification observation of highly structured three-dimensional specimens, such as pill bugs and butterfly wings, and fragile specimens, such as single-cell protozoan parasites, using metal deposition only. Furthermore, it is easily accessible in the field of bioimaging because it does not require any pretreatment and enables surface analysis of biospecimens with an electron microscope using only a single pretreatment process. Protozoa, which are microorganisms, were successfully observed at high magnification without structural changes due to thermal denaturation. Furthermore, metallic film deposition and electrochemical signal measurements using these metallic films were achieved in pill bugs. Full article

Rice varieties with high anthocyanin content are often recognized for their vibrant colors and health benefits. The demand for rice with high anthocyanin is increasing domestically and internationally due to consumers becoming more health-conscious. However, the current increase in yield might not raise the anthocyanin content due to its location in the grain pericarp and seed coat, which are relative to the grain surface area. This study aims to develop rice lines to increase anthocyanin yield per production area by improving rice varieties with small, black, and three grains per spikelet. Accordingly, six rice recombinant inbred lines (RILs) were bred by crossing Niaw Dam Chaw Mai Pai 49 (NDCMP49) with Khao Nok (LLR059). The grain color, size, and number of grains per spikelet were selected from the F₁ to the F₄ population through the pedigree selection method. Six RILs and their parents were assigned in a randomized complete block design (RCBD) with three replications under field conditions during the rainy season of 2021 and 2022 in four locations. The results showed statistically significant differences in environmental conditions, affecting productivity and the yield components of rice lines. Consequently, the rice lines adapted to a specific environment, and there were significant differences in genotype. This study identified three RILs with higher yield performance (13-1 (3842 kg/ha), 374-1 (3699 kg/ha), and 903-3 (3550 kg/ha)) compared with the parent NDCMP49 (1996 kg/ha). However, the grain yields were unstable in the three top-yielding RILs due to varying environmental conditions, indicating that selective breeding requires a specific, narrow environment. Based on grain yield and grain size, the RILs performed better in the grain surface area than in the parent NDCMP49. Moreover, only two RILs (374-1 and 903-3) produced the highest anthocyanin content and yield, although this was lower than in the parent NDCMP49. However, the 374-1 and 903-3 RILs produced more grains, black grains, and three grains per spikelet with high yield and moderate anthocyanin content. They can, therefore, be backcrossed to the parent NDCMP49 to increase the accumulated anthocyanin content with a stable, high yield. This work provides a resource of small grains, black grains, and three grains per spikelet in the rice breeding line for breeding programs in the future. Full article

Background: The gold standard treatment for peripheral arterial disease (PAD) of the common femoral artery (CFA) is open common femoral endarterectomy (CFAE). Interest in the less invasive endovascular treatment (EVT) is growing due to PAD patients’ frequent co-morbidities. Aims: We aimed to evaluate three-year EVT outcomes in multimorbid PAD patients with severe calcified CFA lesions. Methods: Using the prospectively maintained “all-comers” Duesseldorf PTA Registry, we analysed the three-year outcomes of 150 patients with EVT of the CFA. Between January 2017 and October 2023, 66 patients received a rotational excisional atherectomy (REA) followed by a drug-coated balloon angioplasty (DCB), and 84 patients received a DCB alone. Results: All procedures involved the CFA, 49% additionally involved the proximal superficial femoral artery (SFA), and 10% of the lesions involved the profunda femoris artery (PFA). The procedural success rate was 97% and independent of PAD stage, with a higher level of stent implantation in the DCB group (58% vs. 39%, p < 0.05). The primary patency rate at one year was 83% for REA + DCB and 87% for DCB (p = 0.576), while secondary patency after three years was 97%. The MALE rate at three years was mainly driven by cdTLR (REA + DCB: (20%) vs. DCB: (14%), p = 0.377), while major amputations were low in both groups (REA + DCB: 3% vs. DCB: 1%). Overall, the major adverse cardiovascular events (MACEs) rate at three years was low (REA + DCB: (5%) vs. DCB: (11%), p = 0.170). Conclusions: The EVT of severely calcified CFA lesions is safe and effective, with high three-year patency rates and low rates of major adverse limb events (MALEs) and MACEs. This registry demonstrates that vessel preparation with REA minimizes the need for stenting. Full article

Immobilizing different enzymes on membranes can result in biocatalytic active membranes with a self-cleaning capacity toward a complex mixture of foulants. The membrane modification can reduce fouling and enhance filtration performance. Protease, lipase, and amylase were immobilized on poly(vinylidene fluoride) (PVDF) microfiltration membranes using a polydopamine coating in a one-step method. The concentrations of polydopamine precursor and enzymes were optimized during the immobilization. The higher hydrolytic activities were obtained using 0.2 mg/mL of dopamine hydrochloride and 4 mg/mL of enzymes: 0.90 mg_starch/min·cm² for amylase, 10.16 nmol_tyrosine/min·cm² for protease, and 20.48 µmol_{p-nitrophenol}/min·cm² for lipase. Filtration tests using a protein, lipid, and carbohydrate mixture showed that the modified membrane retained 41%, 29%, and 28% of its initial water permeance (1808 ± 39 L/m²·h·bar) after three consecutive filtration cycles, respectively. In contrast, the pristine membrane (initial water permeance of 2016 ± 40 L/m²·h·bar) retained only 23%, 12%, and 8%. Filtrations of milk powder solution were also performed to simulate dairy industry wastewater: the modified membrane maintained 28%, 26%, and 26% of its initial water permeance after three consecutive filtration cycles, respectively, and the pristine membrane retained 34%, 21%, and 7%. The modified membrane showed increased fouling resistance against a mixture of foulants and presented a similar water permeance after three cycles of simulated dairy wastewater filtration. Membrane fouling is reduced by the immobilized enzymes through two mechanisms: increased membrane hydrophilicity (evidenced by the reduced water contact angle after modification) and the enzymatic hydrolysis of foulants as they accumulate on the membrane surface. Full article