|
|
|
| Black Krrsantan: The Book of Boba Fett
|
|
Model BH-14871, Photo by Filippo Roversi
|
|
|
|
Description: Black Krrsantan
Prefix: BH
Detachment: Bounty Hunters Guild
Context: Black Krrsantan: The Book of Boba Fett
Following the death of Jabba and the end of the war, Black Krrsantan was employed by that late Hutt’s cousins; brother and sister crime lords known as “The Twins”. Their cousin’s criminal empire had been taken over by the former bounty hunter Boba Fett, and the Hutts sought Black Krrsantan’s services in wresting control away from the self-appointed Daimyo. Black Krrsantan attempted to assassinate Fett but was captured by his forces. Shortly after, the Twins promised to leave Tatooine, and Black Krrsantan was eventually employed by Boba Fett. As a part of Fett’s forces, he participated in a battle against the Pyke Syndicate, which resulted in a Fett syndicate victory.
|
|
|
|
For 501st membership, only the requirements in black need to be met.
The Bounty Hunters’ Guild defines an additional optional level of costuming excellence. In the page below, requirements for Level 2, referred to as “Infamous”, are listed in blue. These optional requirements are meant for those who strive to meet the highest level of screen accuracy. Please visit the BHG web site for a full description of these standards.
|
|
|
This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
- This document is not intended to be a detailed how-to on costume construction; rather a visual guide to be used for 501st costume approval. Details on construction may be found on the respective costume detachment web forum.
- GMLs uncertain about an aspect of submitted costume shall post questions in the appropriate DL/GML peer review section of the Legion forum.
- Measurements given in this document are intended to be approximate and generalized; not criteria for approval.
- Requirements for all 501st costumes are proportional to the wearer in scale, fit and size.
- Text descriptions are only one part of the guideline. GMLs and costumers must consider both text and pictures (CRL and Reference) when reviewing the costume.
|
|
|
|
General Construction Notes
- The version of the character represented is based on The Book of Boba Fett television show.
- All components should closely match the Black Krrsantan Color Palette.
- Color palette is intended for reference in building, and will only be used in exacting measurement by Detachment for Infamous Level approval. A Basic level approval is only required to be similar, not exact.
- All Armor is constructed from a durable material such as Metal, Fiberglass, Resin, Sintra, HIPS, PVC, PLA, Vac-formed ABS, Firm Rubber, or similar. Foam armor is not permitted.
- Armor has the appearance of thickness and depth.
- All weathering closely matches visual references from The Book of Boba Fett
|
|
|
|
Mask
- Hair is mostly black with grey/silver hair mixed throughout and grey/silver patches above each eyebrow, mustache area, and chin area.
- The eyes, nose, and lips are all clearly visible.
- The mask is constructed from natural or synthetic hair.
- Hair is smooth and well-groomed so the mask’s shape and structure are clear.
- The mask must completely cover the head and neck, without any exposed skin. Black makeup is worn around the eyes.
- Head and mouth may be static or mechanical. Teeth and tongue, consistent with visual references, are visible if the mouth is open.
- Two prominent scars appear above the left eye arcing vertically up the left side of the head.
- A single, smaller scar is present below the left eye running horizontally on the cheek.
- The muzzle area, including the nose and lips, is black in color.
- Six ponytails/dreadlocks are present on the head.
- Two from the back of the head.
- Three are present on the right side of the face (one beginning from the side of the head, one from the cheek area, and one from the chin area).
- One is present on the left side of the face beginning near the cheek area.
- A total of thirteen metallic gold circular bands, similar to PMS Metallic Gold 871c, are present on the larger ponytail/dreadlocks and spaced out according to visual references.
- The longest ponytail/dreadlock, located on the right side of the face near the temple area contains 3 circular bands; all other ponytail/dreadlocks contain 2 bands.
- Smaller, non-banded ponytail/dreadlocks may be present on the left side in the neck area
|
OPTIONAL Level two certification (if applicable):
- Mouth, lips, and eyebrows can articulate and are able to move.
|
|
|
|
Shoulder Armor
- Shoulder armor is ovoid with soft angles on the left and right edges.
- Shoulders are metallic gold, similar to PMS Metallic Gold 871c, with heavy weathering.
- An outer raised lip runs around the perimeter of the shoulder armor.
- The center of the shoulder armor features a hexagonal shape containing an intricate patterned design.
- Intricate patterns on the shoulders are symmetrical.
- There are seven spikes with blunted tips located on the hexagonal shape. One near each corner and one in the center.
- Noticeable damage is present on both shoulders consistent with visual references.
|
|
|
|
Bandolier
- A leather or leather-like bandolier crosses in the front and back, forming an “X” shape, with gold hexagonal plates that are mounted at the junction of each cross on the front and back of the bandolier.
- Two different colors of leather are layered together on the bandolier; beige similar to PMS 14-1118 TCX, and darker brown, similar to PMS 19-1321 TPG.
- The leather straps on the upper half of the bandolier are composed of a thin strip of brown leather on top of a wider, beige leather strip.
- Two stitch lines are present on the thin brown strip running along each edge.
- The leather straps on the lower half of the bandolier are composed of two brown leather strips on top of a wider, beige leather strip.
- The brown strips are flush with the outside edge of the beige leather strip exposing beige leather in the middle.
- Two stitch lines are present on each thin brown strip running along each edge.
- The front hexagonal plate features a raised, intricate design consistent with visual references.
- Eight “bolt-like” details are present on the front hexagonal plate. One in each corner and two in each middle corner.
- Bolt details may be decorative or functional. If decorative, then no other attachment method is visible.
- The rear hexagonal plate contains an indented line along the outer edge and a blaster rifle quick-release clip in the center matching visual references.
- Eight “bolt-like” details are present on the rear hexagonal plate. One in each corner and two in each middle corner, identical to the front plate.
- The center quick-release clip features a larger bolt detail in the center with two smaller bolt details in two corners opposite of each other, and two empty holes in the other corners.
- Bolt details may be decorative or functional. If decorative, then no other attachment method is visible.
- Bandolier features a series of metallic gold, rectangular boxes.
- Boxes are approximately the same height as each facet of the hexagonal plates in the center of the torso and back.
- Four boxes are present on each front upper strap terminating at the shoulder armor.
- The box nearest to the shoulder may be partially covered by the shoulder armor.
- Three boxes are present on each rear upper strap (shoulder blade area) terminating at the shoulder armor.
- The box nearest to the shoulder may be partially covered by the shoulder armor.
- Seven boxes loop under the arm from the front hexagonal plate to the rear hexagonal plate on each lower bandolier strap.
- Boxes present on the lower straps of the bandolier are slightly larger in size compared to the boxes on the upper bandolier straps.
|
OPTIONAL Level two certification (if applicable):
- Bandolier is made of leather.
- Accurate M3 countersunk cap screws are used for the “bolt-like” details on the front and rear hexagonal plates.
- Front M3 screws are a weathered gold to match the hexagonal plate while rear M3 screws are black.
- Blaster Rifle clip present on the rear hexagonal plate is a black PL-S-3 Peak Design Standard Plate camera mount attachment.
|
|
|
|
Belt/Cod Armor and Ammo Boxes/Pouch
- Belt wraps around the waist and connects in the front to a circular top, triangular bottomed cod armor plate.
- Cod armor plate is metallic gold in color, similar to PMS Metallic Gold 871c, and features a raised intricate Celtic knot pattern.
- A large singular leather or leather-like pouch is present on the wearer’s right hip.
- Pouch is constructed of the same materials as the bandolier and has a triangular flap in the front, and strap on each side.
- No closure method is visible on the pouch.
- There are five rectangular boxes present on the belt between the center cod armor and the pouch on the wearer’s right hip.
- There are another ten rectangular boxes after the pouch, wrapping around the waist and terminating at the cod armor plate from the wearer’s left.
- Boxes are smaller in size than those present on the bandolier.
- A minimum of 1" (25.4mm), and a maximum of 2" (50.8mm), of gap separate the cod armor and a rectangular box on each side.
- Boxes are the same metallic gold in color as the cod armor.
- Two medium blonde braids, matching visual references, attached to rings are tied to the belt on the right hip and extend down to the knee area.
|
OPTIONAL Level two certification (if applicable):
- Pouch is made of leather.
|
|
|
|
Fur Suit
- Complete hair suit using natural or synthetic fibers, matching those used on the head.
- Fur suit is mostly black with gray mixed throughout.
- Thigh area on both legs has a higher concentration of gray than the rest of the fur.
- Fur completely covers the body; bald spots, exposed skin, or visible undersuits are not seen.
- Arms are properly proportioned.
|
OPTIONAL Level two certification (if applicable):
- Arm extensions may be used and if used, hair on arms do not extend past the top knuckles of the hands.
|
|
|
|
Claws & Hands
- Dark Grey Gorilla style hands.
- Gloves have distinct fingernails/claws.
- A set of “Knuckle Dusters” is worn on each hand.
- Knuckle dusters are the same metallic gold as the armor and belt boxes.
- Knuckle Dusters consist of a segmented band with four holes that are worn over the fingers.
- Four spikes are present on the knuckle dusters; one atop each finger segment.
- Spikes are blunted at the tip.
- A round-cornered, square-shaped indent is present around the perimeter of each finger segment.
- An intricate pattern consisting of circles and lines, similar to the shoulder armor pattern, is present on the front and back sides of the knuckle dusters.
|
|
|
|
Feet & Toes
- When worn, the feet are completely covered with hair except for the bottom and the toes. “Elephant Stump” look is not acceptable.
- The toes and toenails/claws are visible.
- There are five toes on each foot.
|
|
|
|
Height
- A minimum height of 6'9" (2.1m).
|
|
|
| Optional Accessories
|
|
Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.
|
|
|
|
Blaster Rifle
- Blaster Rifle length is approximately 75% the height of the costumer.
- Blaster Rifle body is predominantly black in color with some gunmetal accents.
- Barrel is predominately gunmetal in color.
- Blue and Red heat tinting is present at the end of the muzzle.
- A thinner, shorter gold/brass tube runs underneath the barrel with black accents.
- Three scopes are present on the top of the blaster rifle with the outer 2 scopes mounted in a sideways fashion.
- The left scope is similar in appearance to a 4x20 rifle scope.
- The center scope is similar in appearance to a single point scope.
- The right scope is similar in appearance to a 4x15 rifle scope.
- A tubular ribbed section runs along underneath the receiver acting as an offhand grip.
- Above the offhand grip, a series of raised vertical bars is housed within an elongated trapezoidal indent.
- A large trigger guard is present offering protection for the entire hand.
- A rectangular plate on the right side of the receiver contains the following:
- Two Red LEDs; one square shaped and one rectangle shaped.
- A small white button-like square with a circle depression below each red LED.
- A raised square detail with a raised circle within it.
- Four “bolt-like” details resembling M3 countersunk cap screws; one in each corner.
- A cutout portion of the blaster is present behind the rectangular plate featuring a brass/gold rod.
- The buttstock of the rifle is shaped similarly to the buttstock of a Barrett’s M107 or M82 sniper rifle.
|
OPTIONAL Level two certification (if applicable):
- Two Red LED lights on the right side of the receiver can illuminate.
|
|
|
This document and all of the images within were created by and are the property of the 501st Legion. Other media owned by Lucasfilm Ltd and Disney are used under authorization. All other uses are prohibited. The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it follows generally accepted ground rules for Star Wars fan groups. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. Copyright and Trademark Lucasfilm Ltd. All rights reserved. Used under authorization.
