|
|
|
| Lieutenant Ochō
|
|
Model ID-8588, Photo by IC-52278
|
|
|
|
Description: Lieutenant Ochō
Prefix: ID
Detachment: Imperial Officer Corps
Context: Star Wars: Visions
Ochō was a human female who lived on the Outer Rim planet Tao during the Imperial Era, and the daughter of a powerful crime family. Ochō's father supported the rebellion, but Ochō joined the Empire.
|
|
|
|
For 501st membership only the requirements in black need to be met.
The Imperial Officer Corps defines additional, optional levels of costuming excellence. In the page below, requirements for Level 2 “Executor” are listed in blue. Requirements for Level 3 “Imperator” are listed in red.
|
|
This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
- This document is not intended to be a detailed how-to on costume construction; rather a visual guide to be used for 501st costume approval. Details on construction may be found on the respective costume detachment web forum.
- GMLs uncertain about an aspect of submitted costume shall post questions in the appropriate DL/GML peer review section of the Legion forum.
- Measurements given in this document are intended to be approximate and generalized; not criteria for approval.
- Requirements for all 501st costumes are proportional to the wearer in scale, fit and size.
- Text descriptions are only one part of the guideline. GMLs and costumers must consider both text and pictures (CRL and Reference) when reviewing the costume.
|
|
|
| Required Costume Components
|
|
The following costume components are present and appear as described below.
|
|
|
|
Hair and facial appearance.
- Hair must be black, and not extend to the shoulder, matching references.
- Red makeup in the “cat’s eye” style is present on the eyes, matching references.
|
OPTIONAL Level two certification (if applicable):
- Hair appears natural.
- If a hair appliance is used, it is styled in a way as to not give the appearance of a wig.
|
|
|
|
Tunic
- Tunic is constructed of a medium to heavy white twill weave fabric.
- Wool or wool-like twill weave is preferred.
- Double-breasted with a left over right closure on the tapered yoke.
- Yoke wraps across the shoulder to the top shoulder seam.
- The standing collar has square corners and is approximately 2 inches tall.
- Collar closes flush and snug; modesty panel is acceptable but not required.
- Two code cylinder pockets on both outside panels of the jacket located half way between the top and bottom on the arm hole.
- Wrist length sleeves without decoration, cuffs, or buttons.
- Fasteners on the uniform must not be visible, including those that would hold the cape in place if present.
- Cape collar edge must lie flush to tunic collar edge.
- There is a welt pocket (functional, or non-functional) approximately 4 inches long and following the angle of the cape’s yoke on the left side.
|
OPTIONAL Level two certification (if applicable):
- There is a dart approximately 2 inches (50.8 mm) in the top center of the yoke.
- Sleeves contain 2 seams. One along the front and one along the back.
- Tunic is constructed without topstitching.
|
|
|
|
Rank Bar
- Rank consists of colored plastic tiles in a single row, mounted on a metal looking bar.
- Worn on the left side of the tunic over the heart, aligned with the code cylinder pocket.
- The bar is approximately 1 inch (25.4 mm) to 1.25 inches (31.75 mm) in height.
- Rank bar has only three blue tiles and three red tiles in a single row.
- Rank tile dimensions and spacing are appropriate and proportional to the sizing of the bar to allow for even spacing from each other and the border of the bar:
- Rogue One/Solo style rank tile dimensions are approximately 0.59 inches (15 mm) wide, 0.82 inches (21 mm) tall, and 0.12 inches (3.2 mm) deep.
- Rank bar corners are a hard 90 degree angle, or slightly rounded.
- Rank tiles are translucent, rectangular, positioned side by side in a vertical orientation, and evenly spaced.
|
|
|
|
Code Cylinders
- Two code cylinders are worn on the uniform, both in the right cylinder pocket.
- Dosimeter style: True radiation dosimeters or exact replicas, with correct clip and blue top.
|
|
|
|
Cape
- The closure is located at the costumer’s right side. The collar overlaps and the opening is approximately 2.5 inches on the shoulder, going down vertically to the bottom of the yoke.
- The yoke is flush against the costumer and may have a seam down the front center, this ends in a point.
- The cape is similar in design to other Imperial Ponchos, but this does not have a front. There is nothing below the yoke.
- The edge of the cape has approximately 1 inch seam around all edges.
- The collar is approximately 3 inches tall at the front and is top stitched with lines approximately every ¼ inch.
- The back of the cape is flat across the back.
- The cape voids at the edge of the costumer’s shoulders.
- The front of the poncho has a piece attached to the yoke but separate from the sides
|
|
|
|
Jodhpur Trousers, Black
- Fabric is a medium weight suiting material matching the tunic.
- Cavalry Twill or a Gabardine style weave is most accurate.
- Trousers are flared riding breeches, with semi-stiff flares to the hip/thigh area.
- Breeches are worn with boots.
- Breeches are neatly pressed or ironed without creases.
- Pockets are acceptable, although must not be visible with the tunic on.
|
|
|
|
Gloves
- Black, wrist length gloves constructed of a smooth, non-textured leather or leather-like material.
- Enclosed fingers.
- No buckles, straps, etc.
|
|
|
|
Belt
- The belt is constructed from a black, non-textured, leather, or a leather-like material.
- Approximately 2 inches (50.8 mm) in width, up to 2.5 inches (63.5 mm) is acceptable.
- There are no loops on the belt.
- A single large snap or rivet is visible approximately 1 inch (25.4 mm) from the buckle.
- The belt to be worn with the snap to the right of the buckle.
- The buckle is constructed from a horizontally brushed metal, or metal looking material.
- The buckle size is approximately 2.6250 inches (66.7 mm) high and 4.1250 inches (104.5 mm) wide with 0.5 inches (12.7 mm) radius rounded corners.
- Buckle is adorned with an un-notched Imperial Code Disk at the center.
- Please refer to the Imperial Buckle reference page for information on accurate and inaccurate style buckles.
|
OPTIONAL Level two certification (if applicable):
- Belt is made of leather.
- Belt has a groove at the top and bottom edge along the length of the belt.
- Buckle has a slight horizontal curve.
|
|
|
|
Officer Boots
- Knee-high, black, riding style, lace-less, smooth non-textured, leather or leather-like material.
- There are no buckles, snap tabs, or decoration.
- The there are no center seams on the front shaft of the boot.
- Boots have conservative heels.
- A single stretch panel or zipper may be present, they are to be hidden on the inner part of the boot shaft.
- Not visible from the front, side, or back.
- The top of the boots may be flat or Spanish Style, but not Cowboy or Super Hero (pointed at the front) style.
- A small V-shaped notch may be present on the back of the boots top.
|
OPTIONAL Level two certification (if applicable):
- Boots are made of leather and may have hidden zippers.
|
OPTIONAL Level three certification (if applicable):
- Exact replicas of English riding (dress) boots, German marching boots, or Equestrian boots.
- Boots have a top adjustment strap on the outside of the boots.
- Boots to have a flat top.
- The straps are set slightly to the rear with the tabs facing the rear.
|
|
|
This document and all of the images within were created by and are the property of the 501st Legion. Other media owned by Lucasfilm Ltd and Disney are used under authorization. All other uses are prohibited. The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it follows generally accepted ground rules for Star Wars fan groups. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. Copyright and Trademark Lucasfilm Ltd. All rights reserved. Used under authorization.
