Seismic code
Seismic codes or earthquake codes are building codes designed to protect property and life in buildings in case of earthquakes. The need for such codes is reflected in the saying, "Earthquakes don't kill people—buildings do." Or in expanded version, “Earthquakes do not injure or kill people. Poorly built manmade structures injure and kill people.”[1]
Origin
While modern seismic code is heavily influenced by earthquakes in California and ensuing California legislation, the origins of seismic code go back to the 1700s in Portugal.[citation needed] Seismic codes are under constant evolution, with changes often instigated by major earthquakes which have caused devastation in highly populated regions or significant research findings regarding critical design approach flaws.
The 1755 Lisbon earthquake resulted in prescriptive rules for building certain kinds of buildings common in the area.[citation needed]
Following the Messina, Italy (1911) earthquake, The Royal Government of Italy established Geological Committee and Engineering Committee in early 1909 to study the disaster and recommend earthquake disaster mitigation measures. The Engineering Committee, after studying the lateral load resistance of buildings which survived the earthquake motion, recommended that the seismic ratio (seismic acceleration divided by the gravity acceleration) equal to 1/12 for the first floor and 1/8 for the floors above should be used in seismic design of buildings. The Committee proposed equivalent vertical forces much larger than the horizontal forces because vertical motion acted as impacts. This is believed to be the first known quantitative recommendation of design seismic forces in the history of seismic codes. The recommendation was adopted in Royal Decree No. 573 of April 29, 1915. The height of the buildings was limited to two stories, and the first story should be designed for a horizontal force equal to 1/8 the second floor weight and the second story for 1/6 of the roof weight. [2]
The Kanto (Tokyo) Japan (1923) and earlier events inspired Japanese engineer Toshikata Sano to develop a lateral force procedure that was officially implemented in the 1924 Japanese Urban Building Law, which directed engineers to design buildings for horizontal forces of about 10% of the weight of the building.[2]
In 1925, the city of Santa Barbara, California, added a building code requirement that structures be designed to withstand horizontal forces, and while nonspecific regarding design loads, is considered the first explicit policy and legal consideration of the seismic safety of structures in the U.S. The city of Palo Alto, California, led by professors at Stanford, also added similar language to its building code in 1926.[3]
In January 1928, the first edition of the Uniform Building Code (UBC) was published, and included an appendix with non-mandatory matter with §2311 recommending a minimum lateral design force for earthquake resistance of V = 0.075W for buildings on foundations with allowable bearing pressures of 4,000 psf or more, and 0.10 W for all other buildings including those on pile foundations.[4] Building weight (seismic mass) was defined as: W = Dead load + Live load. These provisions were inspired by Japan's newly developed seismic code. The non-mandatory lateral design provisions are not known to have been explicitly adopted by any jurisdiction at the time, but may have been used voluntarily for the design of some buildings.[5]: 26
On March 10, 1933, a magnitude 6.4 earthquake struck offshore of Long Beach, California, killing more than 100 and causing significant regional damage, especially to masonry structures and schools. In response, the city of Los Angeles adopted the first earthquake design provisions enforced in the U.S., enacted by City Council under Ordinance No. 72,968 published September 6, 1933.[5]: 24 The requirements included a design lateral base shear V = 0.08 W for regular use buildings, 0.10 W for school buildings and 0.04 W for the portion of a building above a flexible story. Building weight (seismic mass) was defined as W = Dead load + 0.5 Live load (except 1.0 Live for warehouses). Building frames were required to be designed to withstand at least 0.25V independent of any walls.[6]
Immediately after the 1933 Long Beach earthquake, careful analysis of structural failures in that quake by architect Louis John Gill formed the basis for much of the California seismic legislation (Field Act for schools and Riley Act for all buildings).[7][8] The 1933 Riley Act required all California local governments to have a building department and inspect new construction, mandating that all structures in the state be designed to withstand a horizontal acceleration of 0.02 times the acceleration due to gravity.
Around the world
Mexiko
The first Mexico City building code was issued in 1942; since 1966, it contains a complete set of regulations for structural design and has served as a reference for municipalities across the country. In 1976, the code adopted a coherent format for all materials and structural systems, based on limit states design philosophy. In February 2004 a new set of seismic codes was issued.[9]
Spanien
In Spain the seismic code is called the "Norma de Construcción Sismorresistente". (See the article in Spanish Wikipedia)
Vereinigte Staaten
![]() | This section needs expansion. You can help by adding to it. (June 2014) |
In the United States the Federal Emergency Management Agency (FEMA) publishes "Recommended Seismic Provisions for New Buildings and Other Structures".[10]
References
- ^ "Mitigation works: Earthquake" (PDF). Earthquake Engineering Research Institute. Retrieved 26 June 2014.
- ^ a b Otani, Shunsuke (October 2008). "The Dawn of Structural Engineering in Japan" (PDF). 14th World Conference on Earthquake Engineering.
- ^ "Evolution of Codes". Retrieved December 8, 2017.
{{cite web}}
: Cite has empty unknown parameter:|dead-url=
(help) - ^ Uniform Building Code, 1927 Edition. Long Beach, California: International Conference of Building Officials. 1928. pp. 213–214.
- ^ a b SEAOSC Design Guide Vol. 1 “City of Los Angeles Mandatory Earthquake Hazard Reduction in Existing Non-Ductile Concrete Buildings”. International Code Council. 2016. ISBN 978-1-60983-697-9.
- ^ Los Angeles Annual Builders Guide, Vol. 10. Los Angeles, CA: Inter-State Educational Assn. 1933. pp. 12 (amended insert from publisher).
- ^ PEER (Pacific Earthquake Engineering Research Center at the University of California, Berkeley) Tall Buildings Initiative—Task 2 Workshop April 18, 2007
- ^ Rev. C. Douglas Kroll, Journal of San Diego History, "LOUIS JOHN GILL: Famous but Forgotten Architect", San Diego Historical Society Quarterly, Summer 1984, Volume 30, Number 3
- ^ "SEISMIC DESIGN AND CODES IN MEXICO", Mario ORDAZ and Roberto MELIZ, 13th World Conference on Earthquake Engineering Vancouver, B.C., Canada, August 1-6, 2004, Paper No. 4000
- ^ "NEHRP Recommended Seismic Provisions for New Buildings and Other Structures. 2009 Edition", Federal Emergency Management Agency