Fairlane Pins

INDEX
T-Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
L-Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11
End Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Button Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-19
Wire Lanyards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42-43
Ring Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-27
Pull Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Nautical Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-31
Dome Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-39

Fairlane Products | 33792 Doreka Dr., Fraser MI 48026 | Phone: 586-294-6100 | Fax: 586-294-6822 | www.fairlaneproducts.com
QUICK RELEASE BALL LOCK PINS
Selecting the proper Quick Release Ball Lock Pin

1. Select the proper pin diameter.
Our standard inch sizes are 3/16", 1/4", 5/16", 3/8", 1/2" and
5/8. Our standard metric sizes are 5mm, 6mm, 8mm, 10mm,
12mm and 16mm. We also offer 3/4", 7/8" and 1" diameters
as special order.
Pin Diameter
2. Select the proper grip length.
Grip Length
The grip length (also referred to as the useable length) is

measured from the bottom of the handle to the top of the
locking balls. Our standard inch grip lengths range from
1/2" up to 6" and our metric grip lengths range from 10mm
up to 100mm depending on the diameter. Custom lengths
are also available.
3. Select the proper shank material.

17-4 SS Made from heat treated 17-4 stainless steel, they are designed for applications where higher shear strengths are
required. Because they are made from stainless steel, they offer superior corrosion resistance over alloy steel. This combination of
strength and corrosion resistance makes it a good choice for a wide range of demanding applications. RoHS compliant.
300 Series Stainless Steel Made from 300 series stainless, these pins are not designed to be used where shear strengths are
demanding. While these pins offer lower shear strengths than other materials, they are strong enough to meet the needs for many
applications. This material also offers very good corrosion resistance. RoHS compliant.
4130 Alloy Steel Made from heat treated and plated 4130 alloy steel, these pins are ideal where high strength is required and
environmental factors are not an issue. Metric sizes are RoHS compliant.
4. Select the proper handle style.

Handle choice is based on clearance, use and appearance. Our handles are made from either aluminum alloy or stainless steel.
The aluminum handles are anodized or E coated black and are available in Ring, Button, L, T, and Domed configurations. Stainless
handles are available in Ring, Button, Nautical Recessed, and Domed configurations.
Alum T
Alum L
Alum Button
SS Button
Alum Ring
SS Ring
SS Nautical
Recessed
Alum Dome
SS Dome
5. Select lanyard assembly.

Lanyard assemblies are used to attach the pin to a fixture so it does not get misplaced while the pin is not in use. The lanyard
assemblies must be ordered separately. See pages 42 and 43 for our standard assemblies.
Material Specifications
for the Fairlane pins shown in this catalog.
17-4 SS PINS
CRES 17-4PH (Stainless Steel)
(AMS-5643) (UNS S17400) (DIN 1.4542)
Heat Treated Min. RC-40
Tensile Strength = 190,000 lb/in2 Minimum
Passivated Finish
SHANK Metric
(AMS-5643) (UNS S17400) (DIN 1.4542)
Passivated Finish
SPINDLE
(Internal)
(AMS-5643) (UNS S17400) (DIN 1.4542)
Passivated Finish
HANDLES
Aluminum 2024-T4
(Aluminum Ring,
(ASTM-B211) (UNS A92024) (DIN AlCuMg2)
Button, & Domed)
Anodized Finish (Black)
HANDLES
CRES 303 Stainless Steel
(Stainless Ring, Button, (ASTM-A581) (UNS S30300) (DIN 1.4305)
Nautical Recessed,
Passivated Finish
& Domed)
HANDLES
Aluminum 380 Die Cast
(T & L)
(ASTM-B85) (UNS A03800) (DIN AlSi9Cu3)
Anodized Finish or E Coat (Black)
WEAR COLLAR
CRES 303 (Stainless Steel)
(ASTM-A581) (UNS S30300) (DIN 1.4305)
Passivated Finish
ACTUATOR
Aluminum 2024-T4
BUTTON*
Anodized Finish (Blue)
ACTUATOR
Aluminum 2024-T4
BUTTON *
(Aluminum Dome)
Anodized Finish (Clear)
SPRING
(Internal)
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
BALLS
CRES 440C (Stainless Steel)
(QQ-S-763) (UNS S44004) (DIN 1.4125)
Heat Treated -RC (58-62)
Passivated Finish
BAIL
(Ring Handle)
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
SPLIT RING
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
SHANK Inch
300 SERIES SS PINS

CRES 304 (Stainless Steel) (AMS-5639) (UNS S530400)
(DIN 1.4301) or CRES 303 (Stainless Steel) (AMS-5640)
(UNS S30300) (DIN 1.4305)
Passivated Finish

(AMS-5643) (UNS S17400) (DIN 1.4542)
Passivated Finish
Aluminum 2024-T4
CRES 303 Stainless Steel
(ASTM-A581) (UNS S30300) (DIN 1.4305)
Passivated Finish
(ASTM-A581) (UNS S30300) (DIN 1.4305)
Passivated Finish
Aluminum 2024-T4
Aluminum 2024-T4
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
(QQ-S-763) (UNS S44004) (DIN 1.4125)
Passivated Finish
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
STEEL ALLOY 4130 PINS

4130 (Alloy Steel)
(AMS-6370) (UNS G41300) (DIN 1.7218)
Heat Treated RC36-40
Tensile Strength = 160,000 to 180,000 lb/in2
Cadmium Plate Finish
4130 (Alloy Steel)
(AMS-6370) (UNS G41300) (DIN 1.7218)
Heat Treated RC36-40
Tensile Strength = 160,000 to 180,000 lb/in2
Zinc Plated Clear Chromate
(AMS-5643) (UNS S17400) (DIN 1.4542)
Passivated Finish
Aluminum 2024-T4

(ASTM-A581) (UNS S30300) (DIN 1.4305)
Passivated Finish
Aluminum 2024-T4
Aluminum 2024-T4
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
(QQ-S-763) (UNS S44004) (DIN 1.4125)
Passivated Finish
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
(ASTM-A313) (UNS S30200) (DIN 1.4300)
Passivated Finish
*Note: When a stainless Ring, Button, Nautical Recessed, or Domed handle is specified, the actuator button will be made from CRES-303 (Stainless).
Hole Size / Performance Data

Inch
Dia
Metric
Hole Size
Min. Pull-Out
Calculated Double Shear (lbs)
Max
Min
Strength (lbs)
4130 Steel 17-4 Stainless 300 Series SS*
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
*Note: 300 Series Stainless is not recommended in applications where shear forces are a factor.
Dia
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
Calculated Double Shear (N)

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
MA MODIFICATIONS
AVAILABLE
T-Handle | Inch
Dia
3/16
1/4
5/16
3/8
1/2
5/8
Hole Size
Max
.1940
.2540
.3165
.3790
.5050
.6300
Min
.1900
.2500
.3125
.3750
.5000
.6250
Min. Pull-Out
Strength (lbs)
200
230
510
575
1,160
2,070

4130 Steel
4,600
8,200
12,800
18,400
32,800
51,200
17-4 Stainless 300 Series SS*

5,150
9,200
2,200
14,400
3,500
20,600
4,500
36,800
11,500
57,500
These positive locking quick release pins have a wide range of uses in fastening, locating, and alignment applications. The pins will not release until the button on the
handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or removed into or out of a hole. They are available in
three shank materials to meet your application. The handles for the pins listed below are made from 380 aluminum casting with a black finish. The pins are supplied with a
stainless steel split ring for attaching a cable assembly. In addition to the standard sizes shown below, custom solutions and additional sizes are available as special
order. See page 3 for complete specifications.
4130 Steel
Part #
TAAS-18-050
TAAS-18-075
TAAS-18-100
TAAS-18-125
TAAS-18-150
TAAS-18-175
TAAS-18-200
TAAS-18-250
TAAS-18-300
TAAS-18-350
TAAS-18-400
TAAS-25-050
TAAS-25-075
TAAS-25-100
TAAS-25-125
TAAS-25-150
TAAS-25-175
TAAS-25-200
TAAS-25-250
TAAS-25-300
TAAS-25-350
TAAS-25-400
TAAS-31-050
TAAS-31-075
TAAS-31-100
TAAS-31-125
TAAS-31-150
TAAS-31-175
TAAS-31-200
TAAS-31-250
TAAS-31-300
TAAS-31-350
TAAS-31-400
17-4 SS
Part #
TACH-18-050
TACH-18-075
TACH-18-100
TACH-18-125
TACH-18-150
TACH-18-175
TACH-18-200
TACH-18-250
TACH-18-300
TACH-18-350
TACH-18-400
TACH-25-050
TACH-25-075
TACH-25-100
TACH-25-125
TACH-25-150
TACH-25-175
TACH-25-200
TACH-25-250
TACH-25-300
TACH-25-350
TACH-25-400
TACH-31-050
TACH-31-075
TACH-31-100
TACH-31-125
TACH-31-150
TACH-31-175
TACH-31-200
TACH-31-250
TACH-31-300
TACH-31-350
TACH-31-400
300 Series SS
Part #
TACS-25-050
TACS-25-075
TACS-25-100
TACS-25-125
TACS-25-150
TACS-25-175
TACS-25-200
TACS-25-250
TACS-25-300
TACS-25-350
TACS-25-400
TACS-31-050
TACS-31-075
TACS-31-100
TACS-31-125
TACS-31-150
TACS-31-175
TACS-31-200
TACS-31-250
TACS-31-300
TACS-31-350
TACS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
F
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
G
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
H
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
1.81
MA MODIFICATIONS
AVAILABLE
T-Handle | Inch (continued)

Dia
3/16
1/4
5/16
3/8
1/2
5/8
Hole Size
Max
.1940
.2540
.3165
.3790
.5050
.6300
Min
.1900
.2500
.3125
.3750
.5000
.6250
Min. Pull-Out
Strength (lbs)
200
230
510
575
1,160
2,070

4130 Steel
4,600
8,200
12,800
18,400
32,800
51,200

5,150
9,200
2,200
14,400
3,500
20,600
4,500
36,800
11,500
57,500
4130 Steel
Part #
TAAS-37-050
TAAS-37-075
TAAS-37-100
TAAS-37-125
TAAS-37-150
TAAS-37-175
TAAS-37-200
TAAS-37-250
TAAS-37-300
TAAS-37-350
TAAS-37-400
TAAS-50-100
TAAS-50-125
TAAS-50-150
TAAS-50-175
TAAS-50-200
TAAS-50-250
TAAS-50-300
TAAS-50-350
TAAS-50-400
TAAS-50-450
TAAS-50-500
TAAS-50-550
TAAS-50-600
TAAS-62-150
TAAS-62-175
TAAS-62-200
TAAS-62-250
TAAS-62-300
TAAS-62-350
TAAS-62-400
TAAS-62-450
TAAS-62-500
TAAS-62-550
TAAS-62-600
17-4 SS
Part #
TACH-37-050
TACH-37-075
TACH-37-100
TACH-37-125
TACH-37-150
TACH-37-175
TACH-37-200
TACH-37-250
TACH-37-300
TACH-37-350
TACH-37-400
TACH-50-100
TACH-50-125
TACH-50-150
TACH-50-175
TACH-50-200
TACH-50-250
TACH-50-300
TACH-50-350
TACH-50-400
TACH-50-450
TACH-50-500
TACH-50-550
TACH-50-600
TACH-62-150
TACH-62-175
TACH-62-200
TACH-62-250
TACH-62-300
TACH-62-350
TACH-62-400
TACH-62-450
TACH-62-500
TACH-62-550
TACH-62-600
300 Series SS
Part #
TACS-37-050
TACS-37-075
TACS-37-100
TACS-37-125
TACS-37-150
TACS-37-175
TACS-37-200
TACS-37-250
TACS-37-300
TACS-37-350
TACS-37-400
TACS-50-100
TACS-50-125
TACS-50-150
TACS-50-175
TACS-50-200
TACS-50-250
TACS-50-300
TACS-50-350
TACS-50-400
TACS-50-450
TACS-50-500
TACS-50-550
TACS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
D
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
F
.87
.87
.87
.87
.87
.87
.87
.87
.87
.87
.87
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
G
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
H
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
3.07
3.07
3.07
3.07
3.07
3.07
3.07
3.07
3.07
3.07
3.07
MA MODIFICATIONS
AVAILABLE
T-Handle | Metric
Dia
E X PA N D E D
LINE
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or removed into or out of a hole. The shanks are
available in 4130 steel with zinc plating or 17-4PH stainless steel. The handles for the pins listed below are made from 380 aluminum casting with a black finish. The pins
are supplied with a stainless steel split ring for attaching a cable assembly. For specific application requirements, custom modifications are available for this product
line. See page 3 for complete specifications. RoHS compliant.
4130 Steel
Part #
MTAAS-05-010
MTAAS-05-015
MTAAS-05-020
MTAAS-05-025
MTAAS-05-030
MTAAS-05-035
MTAAS-05-040
MTAAS-05-045
MTAAS-05-050
MTAAS-05-060
MTAAS-05-070
MTAAS-05-080
MTAAS-05-090
MTAAS-05-100
MTAAS-06-010
MTAAS-06-015
MTAAS-06-020
MTAAS-06-025
MTAAS-06-030
MTAAS-06-035
MTAAS-06-040
MTAAS-06-045
MTAAS-06-050
MTAAS-06-060
MTAAS-06-070
MTAAS-06-080
MTAAS-06-090
MTAAS-06-100
MTAAS-08-010
MTAAS-08-015
MTAAS-08-020
MTAAS-08-025
MTAAS-08-030
MTAAS-08-035
MTAAS-08-040
MTAAS-08-045
MTAAS-08-050
MTAAS-08-060
MTAAS-08-070
MTAAS-08-080
MTAAS-08-090
MTAAS-08-100
17-4 SS
Part #
MTACH-05-010
MTACH-05-015
MTACH-05-020
MTACH-05-025
MTACH-05-030
MTACH-05-035
MTACH-05-040
MTACH-05-045
MTACH-05-050
MTACH-05-060
MTACH-05-070
MTACH-05-080
MTACH-05-090
MTACH-05-100
MTACH-06-010
MTACH-06-015
MTACH-06-020
MTACH-06-025
MTACH-06-030
MTACH-06-035
MTACH-06-040
MTACH-06-045
MTACH-06-050
MTACH-06-060
MTACH-06-070
MTACH-06-080
MTACH-06-090
MTACH-06-100
MTACH-08-010
MTACH-08-015
MTACH-08-020
MTACH-08-025
MTACH-08-030
MTACH-08-035
MTACH-08-040
MTACH-08-045
MTACH-08-050
MTACH-08-060
MTACH-08-070
MTACH-08-080
MTACH-08-090
MTACH-08-100
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
G
mm
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
H
mm
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
MA MODIFICATIONS
AVAILABLE
T-Handle | Metric (continued)

Dia
E X PA N D E D
LINE
4130 Steel
Part #
MTAAS-10-015
MTAAS-10-020
MTAAS-10-025
MTAAS-10-030
MTAAS-10-035
MTAAS-10-040
MTAAS-10-045
MTAAS-10-050
MTAAS-10-060
MTAAS-10-070
MTAAS-10-080
MTAAS-10-090
MTAAS-10-100
MTAAS-12-020
MTAAS-12-025
MTAAS-12-030
MTAAS-12-035
MTAAS-12-040
MTAAS-12-045
MTAAS-12-050
MTAAS-12-060
MTAAS-12-070
MTAAS-12-080
MTAAS-12-090
MTAAS-12-100
MTAAS-16-025
MTAAS-16-030
MTAAS-16-035
MTAAS-16-040
MTAAS-16-045
MTAAS-16-050
MTAAS-16-060
MTAAS-16-070
MTAAS-16-080
MTAAS-16-090
MTAAS-16-100
17-4 SS
Part #
MTACH-10-015
MTACH-10-020
MTACH-10-025
MTACH-10-030
MTACH-10-035
MTACH-10-040
MTACH-10-045
MTACH-10-050
MTACH-10-060
MTACH-10-070
MTACH-10-080
MTACH-10-090
MTACH-10-100
MTACH-12-020
MTACH-12-025
MTACH-12-030
MTACH-12-035
MTACH-12-040
MTACH-12-045
MTACH-12-050
MTACH-12-060
MTACH-12-070
MTACH-12-080
MTACH-12-090
MTACH-12-100
MTACH-16-025
MTACH-16-030
MTACH-16-035
MTACH-16-040
MTACH-16-045
MTACH-16-050
MTACH-16-060
MTACH-16-070
MTACH-16-080
MTACH-16-090
MTACH-16-100
mm
5
6
8
10
12
16
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
19
19
19
19
19
19
19
19
19
19
19
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
D
mm
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
45
45
45
45
45
45
45
45
45
45
45
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
F
mm
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
G
mm
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
H
mm
50.8
50.8
50.8
50.8
50.8
50.8
50.8
50.8
50.8
50.8
50.8
50.8
50.8
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
57.2
78
78
78
78
78
78
78
78
78
78
78
MA MODIFICATIONS
AVAILABLE
L-Handle | Inch
Dia
3/16
1/4
5/16
3/8
1/2
5/8
Hole Size
Max
.1940
.2540
.3165
.3790
.5050
.6300
Min
.1900
.2500
.3125
.3750
.5000
.6250
Min. Pull-Out
Strength (lbs)
200
230
510
575
1,160
2,070

4130 Steel
4,600
8,200
12,800
18,400
32,800
51,200

5,150
9,200
2,200
14,400
3,500
20,600
4,500
36,800
11,500
57,500
three shank materials to meet your application. The handles for the pins listed below are made from 380 aluminum casting with a black finish. The pins are supplied with a
4130 Steel
Part #
LAAS-18-050
LAAS-18-075
LAAS-18-100
LAAS-18-125
LAAS-18-150
LAAS-18-175
LAAS-18-200
LAAS-18-250
LAAS-18-300
LAAS-18-350
LAAS-18-400
LAAS-25-050
LAAS-25-075
LAAS-25-100
LAAS-25-125
LAAS-25-150
LAAS-25-175
LAAS-25-200
LAAS-25-250
LAAS-25-300
LAAS-25-350
LAAS-25-400
LAAS-31-050
LAAS-31-075
LAAS-31-100
LAAS-31-125
LAAS-31-150
LAAS-31-175
LAAS-31-200
LAAS-31-250
LAAS-31-300
LAAS-31-350
LAAS-31-400
17-4 SS
Part #
LACH-18-050
LACH-18-075
LACH-18-100
LACH-18-125
LACH-18-150
LACH-18-175
LACH-18-200
LACH-18-250
LACH-18-300
LACH-18-350
LACH-18-400
LACH-25-050
LACH-25-075
LACH-25-100
LACH-25-125
LACH-25-150
LACH-25-175
LACH-25-200
LACH-25-250
LACH-25-300
LACH-25-350
LACH-25-400
LACH-31-050
LACH-31-075
LACH-31-100
LACH-31-125
LACH-31-150
LACH-31-175
LACH-31-200
LACH-31-250
LACH-31-300
LACH-31-350
LACH-31-400
300 Series SS
Part #
LACS-25-050
LACS-25-075
LACS-25-100
LACS-25-125
LACS-25-150
LACS-25-175
LACS-25-200
LACS-25-250
LACS-25-300
LACS-25-350
LACS-25-400
LACS-31-050
LACS-31-075
LACS-31-100
LACS-31-125
LACS-31-150
LACS-31-175
LACS-31-200
LACS-31-250
LACS-31-300
LACS-31-350
LACS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
1.21
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
F
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
.76
G
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
H
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
MA MODIFICATIONS
AVAILABLE
L-Handle | Inch (continued)

Dia
3/16
1/4
5/16
3/8
1/2
5/8
Hole Size
Max
.1940
.2540
.3165
.3790
.5050
.6300
Min
.1900
.2500
.3125
.3750
.5000
.6250
Min. Pull-Out
Strength (lbs)
200
230
510
575
1,160
2,070

4130 Steel
4,600
8,200
12,800
18,400
32,800
51,200

5,150
9,200
2,200
14,400
3,500
20,600
4,500
36,800
11,500
57,500
4130 Steel
Part #
LAAS-37-050
LAAS-37-075
LAAS-37-100
LAAS-37-125
LAAS-37-150
LAAS-37-175
LAAS-37-200
LAAS-37-250
LAAS-37-300
LAAS-37-350
LAAS-37-400
LAAS-50-100
LAAS-50-125
LAAS-50-150
LAAS-50-175
LAAS-50-200
LAAS-50-250
LAAS-50-300
LAAS-50-350
LAAS-50-400
LAAS-50-450
LAAS-50-500
LAAS-50-550
LAAS-50-600
LAAS-62-150
LAAS-62-175
LAAS-62-200
LAAS-62-250
LAAS-62-300
LAAS-62-350
LAAS-62-400
LAAS-62-450
LAAS-62-500
LAAS-62-550
LAAS-62-600
17-4 SS
Part #
LACH-37-050
LACH-37-075
LACH-37-100
LACH-37-125
LACH-37-150
LACH-37-175
LACH-37-200
LACH-37-250
LACH-37-300
LACH-37-350
LACH-37-400
LACH-50-100
LACH-50-125
LACH-50-150
LACH-50-175
LACH-50-200
LACH-50-250
LACH-50-300
LACH-50-350
LACH-50-400
LACH-50-450
LACH-50-500
LACH-50-550
LACH-50-600
LACH-62-150
LACH-62-175
LACH-62-200
LACH-62-250
LACH-62-300
LACH-62-350
LACH-62-400
LACH-62-450
LACH-62-500
LACH-62-550
LACH-62-600
300 Series SS
Part #
LACS-37-050
LACS-37-075
LACS-37-100
LACS-37-125
LACS-37-150
LACS-37-175
LACS-37-200
LACS-37-250
LACS-37-300
LACS-37-350
LACS-37-400
LACS-50-100
LACS-50-125
LACS-50-150
LACS-50-175
LACS-50-200
LACS-50-250
LACS-50-300
LACS-50-350
LACS-50-400
LACS-50-450
LACS-50-500
LACS-50-550
LACS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
D
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
1.77
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
F
.87
.87
.87
.87
.87
.87
.87
.87
.87
.87
.87
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
1.11
G
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
H
2.13
2.13
2.13
2.13
2.13
2.13
2.13
2.13
2.13
2.13
2.13
2.37
2.37
2.37
2.37
2.37
2.37
2.37
2.37
2.37
2.37
2.37
2.37
2.37
2.69
2.69
2.69
2.69
2.69
2.69
2.69
2.69
2.69
2.69
2.69
MA MODIFICATIONS
AVAILABLE
L-Handle | Metric
Dia
E X PA N D E D
LINE
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
available in 4130 steel with zinc plating or 17-4PH stainless steel. The handles for the pins listed below are made from 380 aluminum casting with a black finish. The pins
are supplied with a stainless steel split ring for attaching a cable assembly. For specific application requirements, custom modifications are available for this product
line. See page 3 for complete specifications. RoHS compliant.
4130 Steel
Part #
MLAAS-05-010
MLAAS-05-015
MLAAS-05-020
MLAAS-05-025
MLAAS-05-030
MLAAS-05-035
MLAAS-05-040
MLAAS-05-045
MLAAS-05-050
MLAAS-05-060
MLAAS-05-070
MLAAS-05-080
MLAAS-05-090
MLAAS-05-100
MLAAS-06-010
MLAAS-06-015
MLAAS-06-020
MLAAS-06-025
MLAAS-06-030
MLAAS-06-035
MLAAS-06-040
MLAAS-06-045
MLAAS-06-050
MLAAS-06-060
MLAAS-06-070
MLAAS-06-080
MLAAS-06-090
MLAAS-06-100
MLAAS-08-010
MLAAS-08-015
MLAAS-08-020
MLAAS-08-025
MLAAS-08-030
MLAAS-08-035
MLAAS-08-040
MLAAS-08-045
MLAAS-08-050
MLAAS-08-060
MLAAS-08-070
MLAAS-08-080
MLAAS-08-090
MLAAS-08-100
10
17-4 SS
Part #
MLACH-05-010
MLACH-05-015
MLACH-05-020
MLACH-05-025
MLACH-05-030
MLACH-05-035
MLACH-05-040
MLACH-05-045
MLACH-05-050
MLACH-05-060
MLACH-05-070
MLACH-05-080
MLACH-05-090
MLACH-05-100
MLACH-06-010
MLACH-06-015
MLACH-06-020
MLACH-06-025
MLACH-06-030
MLACH-06-035
MLACH-06-040
MLACH-06-045
MLACH-06-050
MLACH-06-060
MLACH-06-070
MLACH-06-080
MLACH-06-090
MLACH-06-100
MLACH-08-010
MLACH-08-015
MLACH-08-020
MLACH-08-025
MLACH-08-030
MLACH-08-035
MLACH-08-040
MLACH-08-045
MLACH-08-050
MLACH-08-060
MLACH-08-070
MLACH-08-080
MLACH-08-090
MLACH-08-100
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
30.7
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
G
mm
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
H
mm
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
MA MODIFICATIONS
AVAILABLE
L-Handle | Metric (continued)

Dia
E X PA N D E D
LINE
4130 Steel
Part #
MLAAS-10-015
MLAAS-10-020
MLAAS-10-025
MLAAS-10-030
MLAAS-10-035
MLAAS-10-040
MLAAS-10-045
MLAAS-10-050
MLAAS-10-060
MLAAS-10-070
MLAAS-10-080
MLAAS-10-090
MLAAS-10-100
MLAAS-12-020
MLAAS-12-025
MLAAS-12-030
MLAAS-12-035
MLAAS-12-040
MLAAS-12-045
MLAAS-12-050
MLAAS-12-060
MLAAS-12-070
MLAAS-12-080
MLAAS-12-090
MLAAS-12-100
MLAAS-16-025
MLAAS-16-030
MLAAS-16-035
MLAAS-16-040
MLAAS-16-045
MLAAS-16-050
MLAAS-16-060
MLAAS-16-070
MLAAS-16-080
MLAAS-16-090
MLAAS-16-100
17-4 SS
Part #
MLACH-10-015
MLACH-10-020
MLACH-10-025
MLACH-10-030
MLACH-10-035
MLACH-10-040
MLACH-10-045
MLACH-10-050
MLACH-10-060
MLACH-10-070
MLACH-10-080
MLACH-10-090
MLACH-10-100
MLACH-12-020
MLACH-12-025
MLACH-12-030
MLACH-12-035
MLACH-12-040
MLACH-12-045
MLACH-12-050
MLACH-12-060
MLACH-12-070
MLACH-12-080
MLACH-12-090
MLACH-12-100
MLACH-16-025
MLACH-16-030
MLACH-16-035
MLACH-16-040
MLACH-16-045
MLACH-16-050
MLACH-16-060
MLACH-16-070
MLACH-16-080
MLACH-16-090
MLACH-16-100
mm
5
6
8
10
12
16
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
19
19
19
19
19
19
19
19
19
19
19
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
D
mm
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
34.8
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
40.6
45
45
45
45
45
45
45
45
45
45
45
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
F
mm
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
22.1
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2
28.2

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
G
mm
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
H
mm
54.1
54.1
54.1
54.1
54.1
54.1
54.1
54.1
54.1
54.1
54.1
54.1
54.1
60.2
60.2
60.2
60.2
60.2
60.2
60.2
60.2
60.2
60.2
60.2
60.2
68.3
68.3
68.3
68.3
68.3
68.3
68.3
68.3
68.3
68.3
68.3
11
MA MODIFICATIONS
AVAILABLE
Aluminum Button Handle | Inch

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
three shank materials to meet your application. The handles for the pins listed below are made from 2024-T4 aluminum and anodized black. The pins are supplied with a
4130 Steel
Part #
BAAS-18-050
BAAS-18-075
BAAS-18-100
BAAS-18-125
BAAS-18-150
BAAS-18-175
BAAS-18-200
BAAS-18-250
BAAS-18-300
BAAS-18-350
BAAS-18-400
BAAS-25-050
BAAS-25-075
BAAS-25-100
BAAS-25-125
BAAS-25-150
BAAS-25-175
BAAS-25-200
BAAS-25-250
BAAS-25-300
BAAS-25-350
BAAS-25-400
BAAS-31-050
BAAS-31-075
BAAS-31-100
BAAS-31-125
BAAS-31-150
BAAS-31-175
BAAS-31-200
BAAS-31-250
BAAS-31-300
BAAS-31-350
BAAS-31-400
12
17-4 SS
Part #
BACH-18-050
BACH-18-075
BACH-18-100
BACH-18-125
BACH-18-150
BACH-18-175
BACH-18-200
BACH-18-250
BACH-18-300
BACH-18-350
BACH-18-400
BACH-25-050
BACH-25-075
BACH-25-100
BACH-25-125
BACH-25-150
BACH-25-175
BACH-25-200
BACH-25-250
BACH-25-300
BACH-25-350
BACH-25-400
BACH-31-050
BACH-31-075
BACH-31-100
BACH-31-125
BACH-31-150
BACH-31-175
BACH-31-200
BACH-31-250
BACH-31-300
BACH-31-350
BACH-31-400
300 Series SS
Part #
BACS-25-050
BACS-25-075
BACS-25-100
BACS-25-125
BACS-25-150
BACS-25-175
BACS-25-200
BACS-25-250
BACS-25-300
BACS-25-350
BACS-25-400
BACS-31-050
BACS-31-075
BACS-31-100
BACS-31-125
BACS-31-150
BACS-31-175
BACS-31-200
BACS-31-250
BACS-31-300
BACS-31-350
BACS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
F
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
G
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
H
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
MA MODIFICATIONS
AVAILABLE
Aluminum Button Handle | Inch (continued)

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
4130 Steel
Part #
BAAS-37-050
BAAS-37-075
BAAS-37-100
BAAS-37-125
BAAS-37-150
BAAS-37-175
BAAS-37-200
BAAS-37-250
BAAS-37-300
BAAS-37-350
BAAS-37-400
BAAS-50-100
BAAS-50-125
BAAS-50-150
BAAS-50-175
BAAS-50-200
BAAS-50-250
BAAS-50-300
BAAS-50-350
BAAS-50-400
BAAS-50-450
BAAS-50-500
BAAS-50-550
BAAS-50-600
BAAS-62-150
BAAS-62-175
BAAS-62-200
BAAS-62-250
BAAS-62-300
BAAS-62-350
BAAS-62-400
BAAS-62-450
BAAS-62-500
BAAS-62-550
BAAS-62-600
17-4 SS
Part #
BACH-37-050
BACH-37-075
BACH-37-100
BACH-37-125
BACH-37-150
BACH-37-175
BACH-37-200
BACH-37-250
BACH-37-300
BACH-37-350
BACH-37-400
BACH-50-100
BACH-50-125
BACH-50-150
BACH-50-175
BACH-50-200
BACH-50-250
BACH-50-300
BACH-50-350
BACH-50-400
BACH-50-450
BACH-50-500
BACH-50-550
BACH-50-600
BACH-62-150
BACH-62-175
BACH-62-200
BACH-62-250
BACH-62-300
BACH-62-350
BACH-62-400
BACH-62-450
BACH-62-500
BACH-62-550
BACH-62-600
300 Series SS
Part #
BACS-37-050
BACS-37-075
BACS-37-100
BACS-37-125
BACS-37-150
BACS-37-175
BACS-37-200
BACS-37-250
BACS-37-300
BACS-37-350
BACS-37-400
BACS-50-100
BACS-50-125
BACS-50-150
BACS-50-175
BACS-50-200
BACS-50-250
BACS-50-300
BACS-50-350
BACS-50-400
BACS-50-450
BACS-50-500
BACS-50-550
BACS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
D
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
F
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
G
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
H
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
13
MA MODIFICATIONS
AVAILABLE
Aluminum Button Handle | Metric

Dia
E X PA N D E D
LINE
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
available in 4130 steel with zinc plating or 17-4PH stainless steel. The handles for the pins listed below are made from 2024-T4 aluminum and anodized black. Stainless
handles are also available. The pins are supplied with a stainless steel split ring for attaching a cable assembly. For specific application requirements, custom
modifications are available for this product line. See page 3 for complete specifications. RoHS compliant.
4130 Steel
Part #
MBAAS-05-010
MBAAS-05-015
MBAAS-05-020
MBAAS-05-025
MBAAS-05-030
MBAAS-05-035
MBAAS-05-040
MBAAS-05-045
MBAAS-05-050
MBAAS-05-060
MBAAS-05-070
MBAAS-05-080
MBAAS-05-090
MBAAS-05-100
MBAAS-06-010
MBAAS-06-015
MBAAS-06-020
MBAAS-06-025
MBAAS-06-030
MBAAS-06-035
MBAAS-06-040
MBAAS-06-045
MBAAS-06-050
MBAAS-06-060
MBAAS-06-070
MBAAS-06-080
MBAAS-06-090
MBAAS-06-100
MBAAS-08-010
MBAAS-08-015
MBAAS-08-020
MBAAS-08-025
MBAAS-08-030
MBAAS-08-035
MBAAS-08-040
MBAAS-08-045
MBAAS-08-050
MBAAS-08-060
MBAAS-08-070
MBAAS-08-080
MBAAS-08-090
MBAAS-08-100
14
17-4 SS
Part #
MBACH-05-010
MBACH-05-015
MBACH-05-020
MBACH-05-025
MBACH-05-030
MBACH-05-035
MBACH-05-040
MBACH-05-045
MBACH-05-050
MBACH-05-060
MBACH-05-070
MBACH-05-080
MBACH-05-090
MBACH-05-100
MBACH-06-010
MBACH-06-015
MBACH-06-020
MBACH-06-025
MBACH-06-030
MBACH-06-035
MBACH-06-040
MBACH-06-045
MBACH-06-050
MBACH-06-060
MBACH-06-070
MBACH-06-080
MBACH-06-090
MBACH-06-100
MBACH-08-010
MBACH-08-015
MBACH-08-020
MBACH-08-025
MBACH-08-030
MBACH-08-035
MBACH-08-040
MBACH-08-045
MBACH-08-050
MBACH-08-060
MBACH-08-070
MBACH-08-080
MBACH-08-090
MBACH-08-100
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
G
mm
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
H
mm
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
MA MODIFICATIONS
AVAILABLE
Aluminum Button Handle | Metric (continued)

Dia
E X PA N D E D
LINE
4130 Steel
Part #
MBAAS-10-015
MBAAS-10-020
MBAAS-10-025
MBAAS-10-030
MBAAS-10-035
MBAAS-10-040
MBAAS-10-045
MBAAS-10-050
MBAAS-10-060
MBAAS-10-070
MBAAS-10-080
MBAAS-10-090
MBAAS-10-100
MBAAS-12-020
MBAAS-12-025
MBAAS-12-030
MBAAS-12-035
MBAAS-12-040
MBAAS-12-045
MBAAS-12-050
MBAAS-12-060
MBAAS-12-070
MBAAS-12-080
MBAAS-12-090
MBAAS-12-100
MBAAS-16-025
MBAAS-16-030
MBAAS-16-035
MBAAS-16-040
MBAAS-16-045
MBAAS-16-050
MBAAS-16-060
MBAAS-16-070
MBAAS-16-080
MBAAS-16-090
MBAAS-16-100
17-4 SS
Part #
MBACH-10-015
MBACH-10-020
MBACH-10-025
MBACH-10-030
MBACH-10-035
MBACH-10-040
MBACH-10-045
MBACH-10-050
MBACH-10-060
MBACH-10-070
MBACH-10-080
MBACH-10-090
MBACH-10-100
MBACH-12-020
MBACH-12-025
MBACH-12-030
MBACH-12-035
MBACH-12-040
MBACH-12-045
MBACH-12-050
MBACH-12-060
MBACH-12-070
MBACH-12-080
MBACH-12-090
MBACH-12-100
MBACH-16-025
MBACH-16-030
MBACH-16-035
MBACH-16-040
MBACH-16-045
MBACH-16-050
MBACH-16-060
MBACH-16-070
MBACH-16-080
MBACH-16-090
MBACH-16-100
mm
5
6
8
10
12
16
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
19
19
19
19
19
19
19
19
19
19
19
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
D
mm
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
F
mm
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
G
mm
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
H
mm
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
15
MA MODIFICATIONS
AVAILABLE
Stainless Steel Button Handle | Inch

Dia
Hole Size
Min. Pull-Out
Strength (lbs)
17-4
300 Series SS*
Max Min
Stainless
Stainless
3/16 .1940 .1900
200
5,150
1/4 .2540 .2500

230
9,200
2,200
5/16 .3165 .3125
510
14,400
3,500
3/8 .3790 .3750
575
20,600
4,500
1/2 .5050 .5000
1,160
36,800
11,500
*Note: 300 Series Stainless is not recommended in applications where shear
forces are a factor.
two types of stainless steel to meet your application. The handles and actuator buttons for the pins listed below are made from 303 stainless steel. The pins are supplied
with a stainless steel split ring for attaching a cable assembly. For specific application requirements, custom modifications are available for this product line. See page 3
for complete specifications.
17-4 SS
Part #
BCCH-18-050
BCCH-18-075
BCCH-18-100
BCCH-18-125
BCCH-18-150
BCCH-18-175
BCCH-18-200
BCCH-18-250
BCCH-18-300
BCCH-18-350
BCCH-18-400
BCCH-25-050
BCCH-25-075
BCCH-25-100
BCCH-25-125
BCCH-25-150
BCCH-25-175
BCCH-25-200
BCCH-25-250
BCCH-25-300
BCCH-25-350
BCCH-25-400
BCCH-31-050
BCCH-31-075
BCCH-31-100
BCCH-31-125
BCCH-31-150
BCCH-31-200
BCCH-31-200
BCCH-31-250
BCCH-31-300
BCCH-31-350
BCCH-31-400
16
300 Series SS
Part #
BCCS-25-050
BCCS-25-075
BCCS-25-100
BCCS-25-125
BCCS-25-150
BCCS-25-175
BCCS-25-200
BCCS-25-250
BCCS-25-300
BCCS-25-350
BCCS-25-400
BCCS-31-050
BCCS-31-075
BCCS-31-100
BCCS-31-125
BCCS-31-150
BCCS-31-200
BCCS-31-200
BCCS-31-250
BCCS-31-300
BCCS-31-350
BCCS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
F
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
G
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
H
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
MA MODIFICATIONS
AVAILABLE
Stainless Steel Button Handle | Inch (continued)

Dia
Hole Size
Min. Pull-Out
Strength (lbs)
17-4
300 Series SS*
Max Min
Stainless
Stainless
3/16 .1940 .1900
200
5,150
1/4 .2540 .2500

230
9,200
2,200
5/16 .3165 .3125
510
14,400
3,500
3/8 .3790 .3750
575
20,600
4,500
1/2 .5050 .5000
1,160
36,800
11,500
17-4 SS
Part #
BCCH-37-050
BCCH-37-075
BCCH-37-100
BCCH-37-125
BCCH-37-150
BCCH-37-175
BCCH-37-200
BCCH-37-250
BCCH-37-300
BCCH-37-350
BCCH-37-400
BCCH-50-100
BCCH-50-125
BCCH-50-150
BCCH-50-175
BCCH-50-200
BCCH-50-250
BCCH-50-300
BCCH-50-350
BCCH-50-400
BCCH-50-450
BCCH-50-500
BCCH-50-550
BCCH-50-600
300 Series SS
Part #
BCCS-37-050
BCCS-37-075
BCCS-37-100
BCCS-37-125
BCCS-37-150
BCCS-37-175
BCCS-37-200
BCCS-37-250
BCCS-37-300
BCCS-37-350
BCCS-37-400
BCCS-50-100
BCCS-50-125
BCCS-50-150
BCCS-50-175
BCCS-50-200
BCCS-50-250
BCCS-50-300
BCCS-50-350
BCCS-50-400
BCCS-50-450
BCCS-50-500
BCCS-50-550
BCCS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
D
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
F
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
G
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
H
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
17
MA MODIFICATIONS
AVAILABLE
Stainless Steel Button Handle | Metric

Dia
mm
5
6
8
10
12
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160

17-4
Stainless
24,400
35,640
63,804
100,101
144,060
handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or removed into or out of a hole. The handles for the
pins listed below are made from 303 stainless steel. The shanks are made from 17-4PH stainless steel. The pins are supplied with a stainless steel split ring for attaching
a cable assembly. For specific application requirements, custom modifications are available for this product line. See page 3 for complete specifications.
RoHS compliant.
17-4 SS
Part #
MBCCH-05-010
MBCCH-05-015
MBCCH-05-020
MBCCH-05-025
MBCCH-05-030
MBCCH-05-035
MBCCH-05-040
MBCCH-05-045
MBCCH-05-050
MBCCH-05-060
MBCCH-05-070
MBCCH-05-080
MBCCH-05-090
MBCCH-05-100
MBCCH-06-010
MBCCH-06-015
MBCCH-06-020
MBCCH-06-025
MBCCH-06-030
MBCCH-06-035
MBCCH-06-040
MBCCH-06-045
MBCCH-06-050
MBCCH-06-060
MBCCH-06-070
MBCCH-06-080
MBCCH-06-090
MBCCH-06-100
MBCCH-08-010
MBCCH-08-015
MBCCH-08-020
MBCCH-08-025
MBCCH-08-030
MBCCH-08-035
MBCCH-08-040
MBCCH-08-045
MBCCH-08-050
MBCCH-08-060
MBCCH-08-070
MBCCH-08-080
MBCCH-08-090
MBCCH-08-100
18
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
G
mm
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
H
mm
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
MA MODIFICATIONS
AVAILABLE
Stainless Steel Button Handle | Metric (continued)

Dia
mm
5
6
8
10
12
17-4 SS
Part #
MBCCH-10-015
MBCCH-10-020
MBCCH-10-025
MBCCH-10-030
MBCCH-10-035
MBCCH-10-040
MBCCH-10-045
MBCCH-10-050
MBCCH-10-060
MBCCH-10-070
MBCCH-10-080
MBCCH-10-090
MBCCH-10-100
MBCCH-12-020
MBCCH-12-025
MBCCH-12-030
MBCCH-12-035
MBCCH-12-040
MBCCH-12-045
MBCCH-12-050
MBCCH-12-060
MBCCH-12-070
MBCCH-12-080
MBCCH-12-090
MBCCH-12-100
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
D
mm
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
F
mm
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
G
mm
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160

17-4
Stainless
24,400
35,640
63,804
100,101
144,060
H
mm
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
19
MA MODIFICATIONS
AVAILABLE
Aluminum Ring Handle | Inch

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
three shank materials to meet your application. The handles for the pins listed below are made from 2024-T4 aluminum and anodized black. Stainless handles are also
available. The pins are supplied with a stainless steel split ring for attaching a cable assembly. In addition to the standard sizes shown below, custom solutions and
additional sizes are available as special order. See page 3 for complete specifications.
4130 Steel
Part #
RAAS-18-050
RAAS-18-075
RAAS-18-100
RAAS-18-125
RAAS-18-150
RAAS-18-175
RAAS-18-200
RAAS-18-250
RAAS-18-300
RAAS-18-350
RAAS-18-400
RAAS-25-050
RAAS-25-075
RAAS-25-100
RAAS-25-125
RAAS-25-150
RAAS-25-175
RAAS-25-200
RAAS-25-250
RAAS-25-300
RAAS-25-350
RAAS-25-400
RAAS-31-050
RAAS-31-075
RAAS-31-100
RAAS-31-125
RAAS-31-150
RAAS-31-175
RAAS-31-200
RAAS-31-250
RAAS-31-300
RAAS-31-350
RAAS-31-400
20
17-4 SS
Part #
RACH-18-050
RACH-18-075
RACH-18-100
RACH-18-125
RACH-18-150
RACH-18-175
RACH-18-200
RACH-18-250
RACH-18-300
RACH-18-350
RACH-18-400
RACH-25-050
RACH-25-075
RACH-25-100
RACH-25-125
RACH-25-150
RACH-25-175
RACH-25-200
RACH-25-250
RACH-25-300
RACH-25-350
RACH-25-400
RACH-31-050
RACH-31-075
RACH-31-100
RACH-31-125
RACH-31-150
RACH-31-175
RACH-31-200
RACH-31-250
RACH-31-300
RACH-31-350
RACH-31-400
300 Series SS
Part #
RACS-25-050
RACS-25-075
RACS-25-100
RACS-25-125
RACS-25-150
RACS-25-175
RACS-25-200
RACS-25-250
RACS-25-300
RACS-25-350
RACS-25-400
RACS-31-050
RACS-31-075
RACS-31-100
RACS-31-125
RACS-31-150
RACS-31-175
RACS-31-200
RACS-31-250
RACS-31-300
RACS-31-350
RACS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
.92
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
G
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
H
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
J
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
K
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
MA MODIFICATIONS
AVAILABLE
Aluminum Ring Handle | Inch (continued)

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
4130 Steel
Part #
RAAS-37-050
RAAS-37-075
RAAS-37-100
RAAS-37-125
RAAS-37-150
RAAS-37-175
RAAS-37-200
RAAS-37-250
RAAS-37-300
RAAS-37-350
RAAS-37-400
RAAS-50-100
RAAS-50-125
RAAS-50-150
RAAS-50-175
RAAS-50-200
RAAS-50-250
RAAS-50-300
RAAS-50-350
RAAS-50-400
RAAS-50-450
RAAS-50-500
RAAS-50-550
RAAS-50-600
RAAS-62-150
RAAS-62-175
RAAS-62-200
RAAS-62-250
RAAS-62-300
RAAS-62-350
RAAS-62-400
RAAS-62-450
RAAS-62-500
RAAS-62-550
RAAS-62-600
17-4 SS
Part #
RACH-37-050
RACH-37-075
RACH-37-100
RACH-37-125
RACH-37-150
RACH-37-175
RACH-37-200
RACH-37-250
RACH-37-300
RACH-37-350
RACH-37-400
RACH-50-100
RACH-50-125
RACH-50-150
RACH-50-175
RACH-50-200
RACH-50-250
RACH-50-300
RACH-50-350
RACH-50-400
RACH-50-450
RACH-50-500
RACH-50-550
RACH-50-600
RACH-62-150
RACH-62-175
RACH-62-200
RACH-62-250
RACH-62-300
RACH-62-350
RACH-62-400
RACH-62-450
RACH-62-500
RACH-62-550
RACH-62-600
300 Series SS
Part #
RACS-37-050
RACS-37-075
RACS-37-100
RACS-37-125
RACS-37-150
RACS-37-175
RACS-37-200
RACS-37-250
RACS-37-300
RACS-37-350
RACS-37-400
RACS-50-100
RACS-50-125
RACS-50-150
RACS-50-175
RACS-50-200
RACS-50-250
RACS-50-300
RACS-50-350
RACS-50-400
RACS-50-450
RACS-50-500
RACS-50-550
RACS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
D
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
G
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
H
.65
.65
.65
.65
.65
.65
.65
.65
.65
.65
.65
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
J
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
K
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
21
MA MODIFICATIONS
AVAILABLE
Aluminum Ring Handle | Metric

Dia
E X PA N D E D
LINE
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
890
1,023
2,268
2,558
5,160
9,207
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
available in 4130 steel with zinc plating or 17-4PH stainless steel. The handles for the pins listed below are made from 2024-T4 aluminum and anodized black. Stainless
handles are also available. The pins are supplied with a stainless steel split ring for attaching a cable assembly. For specific application requirements, custom
modifications are available for this product line. See page 3 for complete specifications. RoHS compliant.
4130 Steel
Part #
MRAAS-05-010
MRAAS-05-015
MRAAS-05-020
MRAAS-05-025
MRAAS-05-030
MRAAS-05-035
MRAAS-05-040
MRAAS-05-045
MRAAS-05-050
MRAAS-05-060
MRAAS-05-070
MRAAS-05-080
MRAAS-05-090
MRAAS-05-100
MRAAS-06-010
MRAAS-06-015
MRAAS-06-020
MRAAS-06-025
MRAAS-06-030
MRAAS-06-035
MRAAS-06-040
MRAAS-06-045
MRAAS-06-050
MRAAS-06-060
MRAAS-06-070
MRAAS-06-080
MRAAS-06-090
MRAAS-06-100
MRAAS-08-010
MRAAS-08-015
MRAAS-08-020
MRAAS-08-025
MRAAS-08-030
MRAAS-08-035
MRAAS-08-040
MRAAS-08-045
MRAAS-08-050
MRAAS-08-060
MRAAS-08-070
MRAAS-08-080
MRAAS-08-090
MRAAS-08-100
22
17-4 SS
Part #
MRACH-05-010
MRACH-05-015
MRACH-05-020
MRACH-05-025
MRACH-05-030
MRACH-05-035
MRACH-05-040
MRACH-05-045
MRACH-05-050
MRACH-05-060
MRACH-05-070
MRACH-05-080
MRACH-05-090
MRACH-05-100
MRACH-06-010
MRACH-06-015
MRACH-06-020
MRACH-06-025
MRACH-06-030
MRACH-06-035
MRACH-06-040
MRACH-06-045
MRACH-06-050
MRACH-06-060
MRACH-06-070
MRACH-06-080
MRACH-06-090
MRACH-06-100
MRACH-08-010
MRACH-08-015
MRACH-08-020
MRACH-08-025
MRACH-08-030
MRACH-08-035
MRACH-08-040
MRACH-08-045
MRACH-08-050
MRACH-08-060
MRACH-08-070
MRACH-08-080
MRACH-08-090
MRACH-08-100
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
G
mm
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
H
mm
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
K
mm
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
MA MODIFICATIONS
AVAILABLE
Aluminum Ring Handle | Metric (continued)

Dia
E X PA N D E D
LINE
4130 Steel
Part #
MRAAS-10-015
MRAAS-10-020
MRAAS-10-025
MRAAS-10-030
MRAAS-10-035
MRAAS-10-040
MRAAS-10-045
MRAAS-10-050
MRAAS-10-060
MRAAS-10-070
MRAAS-10-080
MRAAS-10-090
MRAAS-10-100
MRAAS-12-020
MRAAS-12-025
MRAAS-12-030
MRAAS-12-035
MRAAS-12-040
MRAAS-12-045
MRAAS-12-050
MRAAS-12-060
MRAAS-12-070
MRAAS-12-080
MRAAS-12-090
MRAAS-12-100
MRAAS-16-025
MRAAS-16-030
MRAAS-16-035
MRAAS-16-040
MRAAS-16-045
MRAAS-16-050
MRAAS-16-060
MRAAS-16-070
MRAAS-16-080
MRAAS-16-090
MRAAS-16-100
17-4 SS
Part #
MRACH-10-015
MRACH-10-020
MRACH-10-025
MRACH-10-030
MRACH-10-035
MRACH-10-040
MRACH-10-045
MRACH-10-050
MRACH-10-060
MRACH-10-070
MRACH-10-080
MRACH-10-090
MRACH-10-100
MRACH-12-020
MRACH-12-025
MRACH-12-030
MRACH-12-035
MRACH-12-040
MRACH-12-045
MRACH-12-050
MRACH-12-060
MRACH-12-070
MRACH-12-080
MRACH-12-090
MRACH-12-100
MRACH-16-025
MRACH-16-030
MRACH-16-035
MRACH-16-040
MRACH-16-045
MRACH-16-050
MRACH-16-060
MRACH-16-070
MRACH-16-080
MRACH-16-090
MRACH-16-100
mm
5
6
8
10
12
16
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
19
19
19
19
19
19
19
19
19
19
19
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
D
mm
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
Min. Pull-Out
Strength (N)
4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
890
1,023
2,268
2,558
5,160
9,207
F
mm
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
G
mm
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
H
mm
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
K
mm
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
23
MA MODIFICATIONS
AVAILABLE
Stainless Steel Ring Handle | Inch

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
two types of stainless steel to meet your application. The handles and actuator buttons for the pins listed below are made from 303 stainless steel. The pins are supplied
with a stainless steel split ring for attaching a cable assembly. In addition to the standard sizes shown below, custom solutions and additional sizes are available as
special order. See page 3 for complete specifications.
17-4 SS
Part #
RCCH-18-050
RCCH-18-075
RCCH-18-100
RCCH-18-125
RCCH-18-150
RCCH-18-175
RCCH-18-200
RCCH-18-250
RCCH-18-300
RCCH-18-350
RCCH-18-400
RCCH-25-050
RCCH-25-075
RCCH-25-100
RCCH-25-125
RCCH-25-150
RCCH-25-175
RCCH-25-200
RCCH-25-250
RCCH-25-300
RCCH-25-350
RCCH-25-400
RCCH-31-050
RCCH-31-075
RCCH-31-100
RCCH-31-125
RCCH-31-150
RCCH-31-175
RCCH-31-200
RCCH-31-250
RCCH-31-300
RCCH-31-350
RCCH-31-400
24
300 Series SS
Part #
RCCS-25-050
RCCS-25-075
RCCS-25-100
RCCS-25-125
RCCS-25-150
RCCS-25-175
RCCS-25-200
RCCS-25-250
RCCS-25-300
RCCS-25-350
RCCS-25-400
RCCS-31-050
RCCS-31-075
RCCS-31-100
RCCS-31-125
RCCS-31-150
RCCS-31-175
RCCS-31-200
RCCS-31-250
RCCS-31-300
RCCS-31-350
RCCS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
92
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
G
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
H
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
.59
J
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
K
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
MA MODIFICATIONS
AVAILABLE
Stainless Steel Ring Handle | Inch (continued)

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
17-4 SS
Part #
RCCH-37-050
RCCH-37-075
RCCH-37-100
RCCH-37-125
RCCH-37-150
RCCH-37-175
RCCH-37-200
RCCH-37-250
RCCH-37-300
RCCH-37-350
RCCH-37-400
RCCH-50-100
RCCH-50-125
RCCH-50-150
RCCH-50-175
RCCH-50-200
RCCH-50-250
RCCH-50-300
RCCH-50-350
RCCH-50-400
RCCH-50-450
RCCH-50-500
RCCH-50-550
RCCH-50-600
RCCH-62-150
RCCH-62-175
RCCH-62-200
RCCH-62-250
RCCH-62-300
RCCH-62-350
RCCH-62-400
RCCH-62-450
RCCH-62-500
RCCH-62-550
RCCH-62-600
300 Series SS
Part #
RCCS-37-050
RCCS-37-075
RCCS-37-100
RCCS-37-125
RCCS-37-150
RCCS-37-175
RCCS-37-200
RCCS-37-250
RCCS-37-300
RCCS-37-350
RCCS-37-400
RCCS-50-100
RCCS-50-125
RCCS-50-150
RCCS-50-175
RCCS-50-200
RCCS-50-250
RCCS-50-300
RCCS-50-350
RCCS-50-400
RCCS-50-450
RCCS-50-500
RCCS-50-550
RCCS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
D
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.01
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.27
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
1.65
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
G
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
H
.65
.65
.65
.65
.65
.65
.65
.65
.65
.65
.65
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
J
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
2.57
K
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.43
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
1.72
25
MA MODIFICATIONS
AVAILABLE
Stainless Steel Ring Handle | Metric

Dia
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
Calculated
Double Shear (N)
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or removed into or out of a hole. The handles for the
pins listed below are made from 303 stainless steel. The shanks are made from 17-4PH stainless steel. The pins are supplied with a stainless steel split ring for attaching
a cable assembly. For specific application requirements, custom modifications are available for this product line. See page 3 for complete specifications.
RoHS compliant.
17-4 SS
Part #
MRCCH-05-010
MRCCH-05-015
MRCCH-05-020
MRCCH-05-025
MRCCH-05-300
MRCCH-05-035
MRCCH-05-040
MRCCH-05-045
MRCCH-05-050
MRCCH-05-060
MRCCH-05-070
MRCCH-05-080
MRCCH-05-090
MRCCH-05-100
MRCCH-06-010
MRCCH-06-015
MRCCH-06-020
MRCCH-06-025
MRCCH-06-030
MRCCH-06-035
MRCCH-06-040
MRCCH-06-045
MRCCH-06-050
MRCCH-06-060
MRCCH-06-070
MRCCH-06-080
MRCCH-06-090
MRCCH-06-100
MRCCH-08-010
MRCCH-08-015
MRCCH-08-020
MRCCH-08-025
MRCCH-08-030
MRCCH-08-035
MRCCH-08-040
MRCCH-08-045
MRCCH-08-050
MRCCH-08-060
MRCCH-08-070
MRCCH-08-080
MRCCH-08-090
MRCCH-08-100
26
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.1
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
23.4
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
G
mm
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
H
mm
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
J
mm
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
36.8
K
mm
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
MA MODIFICATIONS
AVAILABLE
Stainless Steel Ring Handle | Metric (continued)

Dia
mm
5
6
8
10
12
16
17-4 SS
Part #
MRCCH-10-015
MRCCH-10-020
MRCCH-10-025
MRCCH-10-030
MRCCH-10-035
MRCCH-10-040
MRCCH-10-045
MRCCH-10-050
MRCCH-10-060
MRCCH-10-070
MRCCH-10-080
MRCCH-10-090
MRCCH-10-100
MRCCH-12-020
MRCCH-12-025
MRCCH-12-030
MRCCH-12-035
MRCCH-12-040
MRCCH-12-045
MRCCH-12-050
MRCCH-12-060
MRCCH-12-070
MRCCH-12-080
MRCCH-12-090
MRCCH-12-100
MRCCH-16-025
MRCCH-16-030
MRCCH-16-035
MRCCH-16-040
MRCCH-16-045
MRCCH-16-050
MRCCH-16-060
MRCCH-16-070
MRCCH-16-080
MRCCH-16-090
MRCCH-16-100
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
19
19
19
19
19
19
19
19
19
19
19
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
D
mm
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
32.3
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
41.9
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
G
mm
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
H
mm
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
J
mm
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
38.6
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
65.3
Mn. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
Calculated
Double Shear (N)
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
K
mm
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
43.7
27
MA MODIFICATIONS
AVAILABLE
Stainless Steel Nautical Recessed Handle | Inch

Dia
3/16
1/4
5/16
3/8
1/2
5/8
Hole Size
Max
.1940
.2540
.3165
.3790
.5050
.6300
Min
.1900
.2500
.3125
.3750
.5000
.6250
Min. Pull-Out
Strength (lbs)
200
230
510
575
1,160
2,070

17-4
300 Series SS*
Stainless
Stainless
5,150
9,200
2,200
14,400
3,500
20,600
4,500
36,800
11,500
57,500

two stainless shank materials to meet your application. The handles are designed to prevent accidental release and are machined from 303 stainless steel. These pins
are not supplied with stainless steel split rings. For specific application requirements, custom modifications are available for this product line. See page 3 for complete
specifications. If a lanyard is ordered with the recessed handle, the lanyard will be attached directly to the pin without a split ring.
17-4 SS
Part #
NCCH-18-050
NCCH-18-075
NCCH-18-100
NCCH-18-125
NCCH-18-150
NCCH-18-175
NCCH-18-200
NCCH-18-250
NCCH-18-300
NCCH-18-350
NCCH-18-400
NCCH-25-050
NCCH-25-075
NCCH-25-100
NCCH-25-125
NCCH-25-150
NCCH-25-175
NCCH-25-200
NCCH-25-250
NCCH-25-300
NCCH-25-350
NCCH-25-400
NCCH-31-050
NCCH-31-075
NCCH-31-100
NCCH-31-125
NCCH-31-150
NCCH-31-175
NCCH-31-200
NCCH-31-250
NCCH-31-300
NCCH-31-350
NCCH-31-400
28
300 Series SS
Part #
NCCS-25-050
NCCS-25-075
NCCS-25-100
NCCS-25-125
NCCS-25-150
NCCS-25-175
NCCS-25-200
NCCS-25-250
NCCS-25-300
NCCS-25-350
NCCS-25-400
NCCS-31-050
NCCS-31-075
NCCS-31-100
NCCS-31-125
NCCS-31-150
NCCS-31-175
NCCS-31-200
NCCS-31-250
NCCS-31-300
NCCS-31-350
NCCS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
.97
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
F
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
.64
Button
G
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
.23
H
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
MA MODIFICATIONS
AVAILABLE
Stainless Steel Nautical Recessed Handle | Inch (continued)

Dia
3/16
1/4
5/16
3/8
1/2
5/8
Hole Size
Max
.1940
.2540
.3165
.3790
.5050
.6300
Min
.1900
.2500
.3125
.3750
.5000
.6250
Min. Pull-Out
Strength (lbs)
200
230
510
575
1,160
2,070

17-4
300 Series SS*
Stainless
Stainless
5,150
9,200
2,200
14,400
3,500
20,600
4,500
36,800
11,500
57,500

17-4 SS
Part #
NCCH-37-050
NCCH-37-075
NCCH-37-100
NCCH-37-125
NCCH-37-150
NCCH-37-175
NCCH-37-200
NCCH-37-250
NCCH-37-300
NCCH-37-350
NCCH-37-400
NCCH-50-100
NCCH-50-125
NCCH-50-150
NCCH-50-175
NCCH-50-200
NCCH-50-250
NCCH-50-300
NCCH-50-350
NCCH-50-400
NCCH-50-450
NCCH-50-500
NCCH-50-550
NCCH-50-600
NCCH-62-150
NCCH-62-175
NCCH-62-200
NCCH-62-250
NCCH-62-300
NCCH-62-350
NCCH-62-400
NCCH-62-450
NCCH-62-500
NCCH-62-550
NCCH-62-600
300 Series SS
Part #
NCCS-37-050
NCCS-37-075
NCCS-37-100
NCCS-37-125
NCCS-37-150
NCCS-37-175
NCCS-37-200
NCCS-37-250
NCCS-37-300
NCCS-37-350
NCCS-37-400
NCCS-50-100
NCCS-50-125
NCCS-50-150
NCCS-50-175
NCCS-50-200
NCCS-50-250
NCCS-50-300
NCCS-50-350
NCCS-50-400
NCCS-50-450
NCCS-50-500
NCCS-50-550
NCCS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
D
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.31
1.69
1.69
1.69
1.69
1.69
1.69
1.69
1.69
1.69
1.69
1.69
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
F
.66
.66
.66
.66
.66
.66
.66
.66
.66
.66
.66
.89
.89
.89
.89
.89
.89
.89
.89
.89
.89
.89
.89
.89
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
Button
G
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.29
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.42
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
.54
H
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
29
MA MODIFICATIONS
AVAILABLE
Stainless Steel Nautical Recessed Handle | Metric

Dia
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
Calculated
Double Shear (N)
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or removed into or out of a hole. The handles are
designed to prevent accidental release and are machined from 303 stainless steel. The shafts are made from 17-4PH stainless steel. These pins are not supplied with
stainless steel split rings. For specific application requirements, custom modifications are available for this product line. See page 3 for complete specifications. RoHS
compliant. If a lanyard is ordered with the recessed handle, the lanyard will be attached directly to the pin without a split ring.
17-4 SS
Part #
MNCCH-05-010
MNCCH-05-015
MNCCH-05-020
MNCCH-05-025
MNCCH-05-030
MNCCH-05-035
MNCCH-05-040
MNCCH-05-045
MNCCH-05-050
MNCCH-05-060
MNCCH-05-070
MNCCH-05-080
MNCCH-05-090
MNCCH-05-100
MNCCH-06-010
MNCCH-06-015
MNCCH-06-020
MNCCH-06-025
MNCCH-06-030
MNCCH-06-035
MNCCH-06-040
MNCCH-06-045
MNCCH-06-050
MNCCH-06-060
MNCCH-06-070
MNCCH-06-080
MNCCH-06-090
MNCCH-06-100
MNCCH-08-010
MNCCH-08-015
MNCCH-08-020
MNCCH-08-025
MNCCH-08-030
MNCCH-08-035
MNCCH-08-040
MNCCH-08-045
MNCCH-08-050
MNCCH-08-060
MNCCH-08-070
MNCCH-08-080
MNCCH-08-090
MNCCH-08-100
30
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
16.3
Button
G
mm
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
5.8
H
mm
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
Stainless Steel Nautical Recessed Handle | Metric (continued)

Dia
mm
5
6
8
10
12
16
17-4 SS
Part #
MNCCH-10-015
MNCCH-10-020
MNCCH-10-025
MNCCH-10-030
MNCCH-10-035
MNCCH-10-040
MNCCH-10-045
MNCCH-10-050
MNCCH-10-060
MNCCH-10-070
MNCCH-10-080
MNCCH-10-090
MNCCH-10-100
MNCCH-12-020
MNCCH-12-025
MNCCH-12-030
MNCCH-12-035
MNCCH-12-040
MNCCH-12-045
MNCCH-12-050
MNCCH-12-060
MNCCH-12-070
MNCCH-12-080
MNCCH-12-090
MNCCH-12-100
MNCCH-16-025
MNCCH-16-030
MNCCH-16-035
MNCCH-16-040
MNCCH-16-045
MNCCH-16-050
MNCCH-16-060
MNCCH-16-070
MNCCH-16-080
MNCCH-16-090
MNCCH-16-100
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
19
19
19
19
19
19
19
19
19
19
19
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
D
mm
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
23.8
23.8
23.8
23.8
23.8
23.8
23.8
23.8
23.8
23.8
23.8
F
mm
16.8
16.8
16.8
16.8
16.8
16.8
16.8
16.8
16.8
16.8
16.8
16.8
16.8
22.6
22.6
22.6
22.6
22.6
22.6
22.6
22.6
22.6
22.6
22.6
22.6
28.5
28.5
28.5
28.5
28.5
28.5
28.5
28.5
28.5
28.5
28.5
Button
G
mm
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
10.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
13.7
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
MA MODIFICATIONS
AVAILABLE
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
Calculated
Double Shear (N)
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
H
mm
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
36.5
36.5
36.5
36.5
36.5
36.5
36.5
36.5
36.5
36.5
36.5
31
MA MODIFICATIONS
AVAILABLE
Aluminum Dome Handle | Inch

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
three shank materials to meet your application. The dome actuator buttons are made from 2024-T4 aluminum and clear anodized. The handles are made from 2024-T4
aluminum and anodized black. Handle has hole for optional wire lanyard attachment. The large ergonomic dome actuator button facilitates easy installation and removal
of the pin. They are ideal in applications where there is repetitive or frequent use of the pin. In addition, they can be used in situations where the operator is wearing
gloves or has limited range of hand motion. They also add a unique look and feel that is not available with other pin styles and offer a large area for engraving or stamping
to add logos, instructions, etc. For specific application requirements, custom modifications are available for this product line. See page 3 for complete specifications.
4130 Steel
Part #
DAAS-18-050
DAAS-18-075
DAAS-18-100
DAAS-18-125
DAAS-18-150
DAAS-18-175
DAAS-18-200
DAAS-18-250
DAAS-18-300
DAAS-18-350
DAAS-18-400
DAAS-25-050
DAAS-25-075
DAAS-25-100
DAAS-25-125
DAAS-25-150
DAAS-25-175
DAAS-25-200
DAAS-25-250
DAAS-25-300
DAAS-25-350
DAAS-25-400
DAAS-31-050
DAAS-31-075
DAAS-31-100
DAAS-31-125
DAAS-31-150
DAAS-31-175
DAAS-31-200
DAAS-31-250
DAAS-31-300
DAAS-31-350
DAAS-31-400
32
17-4 SS
Part #
DACH-18-050
DACH-18-075
DACH-18-100
DACH-18-125
DACH-18-150
DACH-18-175
DACH-18-200
DACH-18-250
DACH-18-300
DACH-18-350
DACH-18-400
DACH-25-050
DACH-25-075
DACH-25-100
DACH-25-125
DACH-25-150
DACH-25-175
DACH-25-200
DACH-25-250
DACH-25-300
DACH-25-350
DACH-25-400
DACH-31-050
DACH-31-075
DACH-31-100
DACH-31-125
DACH-31-150
DACH-31-175
DACH-31-200
DACH-31-250
DACH-31-300
DACH-31-350
DACH-31-400
300 Series SS
Part #
DACS-25-050
DACS-25-075
DACS-25-100
DACS-25-125
DACS-25-150
DACS-25-175
DACS-25-200
DACS-25-250
DACS-25-300
DACS-25-350
DACS-25-400
DACS-31-050
DACS-31-075
DACS-31-100
DACS-31-125
DACS-31-150
DACS-31-175
DACS-31-200
DACS-31-250
DACS-31-300
DACS-31-350
DACS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
F
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
G
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
H
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
MA MODIFICATIONS
AVAILABLE
Aluminum Dome Handle | Inch (continued)

Dia
Hole Size
Min. Pull-Out
Max
Min
Strength (lbs)
3/16
.1940 .1900
200
4,600
5,150
1/4
.2540 .2500
230
8,200
9,200
2,200
5/16
.3165 .3125
510
12,800
14,400
3,500
3/8
.3790 .3750
575
18,400
20,600
4,500
1/2
.5050 .5000
1,160
32,800
36,800
11,500
5/8
.6300 .6250
2,070
51,200
57,500
4130 Steel
Part #
DAAS-37-050
DAAS-37-075
DAAS-37-100
DAAS-37-125
DAAS-37-150
DAAS-37-175
DAAS-37-200
DAAS-37-250
DAAS-37-300
DAAS-37-350
DAAS-37-400
DAAS-50-100
DAAS-50-125
DAAS-50-150
DAAS-50-175
DAAS-50-200
DAAS-50-250
DAAS-50-300
DAAS-50-350
DAAS-50-400
DAAS-50-450
DAAS-50-500
DAAS-50-550
DAAS-50-600
DAAS-62-150
DAAS-62-175
DAAS-62-200
DAAS-62-250
DAAS-62-300
DAAS-62-350
DAAS-62-400
DAAS-62-450
DAAS-62-500
DAAS-62-550
DAAS-62-600
17-4 SS
Part #
DACH-37-050
DACH-37-075
DACH-37-100
DACH-37-125
DACH-37-150
DACH-37-175
DACH-37-200
DACH-37-250
DACH-37-300
DACH-37-350
DACH-37-400
DACH-50-100
DACH-50-125
DACH-50-150
DACH-50-175
DACH-50-200
DACH-50-250
DACH-50-300
DACH-50-350
DACH-50-400
DACH-50-450
DACH-50-500
DACH-50-550
DACH-50-600
DACH-62-150
DACH-62-175
DACH-62-200
DACH-62-250
DACH-62-300
DACH-62-350
DACH-62-400
DACH-62-450
DACH-62-500
DACH-62-550
DACH-62-600
300 Series SS
Part #
DACS-37-050
DACS-37-075
DACS-37-100
DACS-37-125
DACS-37-150
DACS-37-175
DACS-37-200
DACS-37-250
DACS-37-300
DACS-37-350
DACS-37-400
DACS-50-100
DACS-50-125
DACS-50-150
DACS-50-175
DACS-50-200
DACS-50-250
DACS-50-300
DACS-50-350
DACS-50-400
DACS-50-450
DACS-50-500
DACS-50-550
DACS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
.6235
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
.6220
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
.750
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
.580
D
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
1.84
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
.94
F
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
1.10
G
.932
.932
.932
.932
.932
.932
.932
.932
.932
.932
.932
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
H
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
33
MA MODIFICATIONS
AVAILABLE
Aluminum Dome Handle | Metric

Dia
E X PA N D E D
LINE
mm
5
6
8
10
12
16
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
available in 4130 steel with zinc plating or 17-4PH stainless steel. Handle has hole for optional wire lanyard attachment. The dome actuator buttons are made from
2024-T4 aluminum and clear anodized. The handles are made from 2024-T4 aluminum and anodized black. The large ergonomic dome actuator button facilitates easy
installation and removal of the pin. They are ideal in applications where there is repetitive or frequent use of the pin. In addition, they can be used in situations where
the operator is wearing gloves or has limited range of hand motion. They also add a unique look and feel that is not available with other pin styles and offer a large area
for engraving or stamping to add logos, instructions, etc. For specific application requirements, custom modifications are available for this product line. See page 3 for
complete specifications. RoHS compliant.
4130 Steel
Part #
MDAAS-05-010
MDAAS-05-015
MDAAS-05-020
MDAAS-05-025
MDAAS-05-030
MDAAS-05-035
MDAAS-05-040
MDAAS-05-045
MDAAS-05-050
MDAAS-05-060
MDAAS-05-070
MDAAS-05-080
MDAAS-05-090
MDAAS-05-100
MDAAS-06-010
MDAAS-06-015
MDAAS-06-020
MDAAS-06-025
MDAAS-06-030
MDAAS-06-035
MDAAS-06-040
MDAAS-06-045
MDAAS-06-050
MDAAS-06-060
MDAAS-06-070
MDAAS-06-080
MDAAS-06-090
MDAAS-06-100
MDAAS-08-010
MDAAS-08-015
MDAAS-08-020
MDAAS-08-025
MDAAS-08-030
MDAAS-08-035
MDAAS-08-040
MDAAS-08-045
MDAAS-08-050
MDAAS-08-060
MDAAS-08-070
MDAAS-08-080
MDAAS-08-090
MDAAS-08-100
34
17-4 SS
Part #
MDACH-05-010
MDACH-05-015
MDACH-05-020
MDACH-05-025
MDACH-05-030
MDACH-05-035
MDACH-05-040
MDACH-05-045
MDACH-05-050
MDACH-05-060
MDACH-05-070
MDACH-05-080
MDACH-05-090
MDACH-05-100
MDACH-06-010
MDACH-06-015
MDACH-06-020
MDACH-06-025
MDACH-06-030
MDACH-06-035
MDACH-06-040
MDACH-06-045
MDACH-06-050
MDACH-06-060
MDACH-06-070
MDACH-06-080
MDACH-06-090
MDACH-06-100
MDACH-08-010
MDACH-08-015
MDACH-08-020
MDACH-08-025
MDACH-08-030
MDACH-08-035
MDACH-08-040
MDACH-08-045
MDACH-08-050
MDACH-08-060
MDACH-08-070
MDACH-08-080
MDACH-08-090
MDACH-08-100
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
G
mm
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
H
mm
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
MA MODIFICATIONS
AVAILABLE
Aluminum Dome Handle | Metric (continued)

Dia
E X PA N D E D
LINE
4130 Steel
Part #
MDAAS-10-015
MDAAS-10-020
MDAAS-10-025
MDAAS-10-030
MDAAS-10-035
MDAAS-10-040
MDAAS-10-045
MDAAS-10-050
MDAAS-10-060
MDAAS-10-070
MDAAS-10-080
MDAAS-10-090
MDAAS-10-100
MDAAS-12-020
MDAAS-12-025
MDAAS-12-030
MDAAS-12-035
MDAAS-12-040
MDAAS-12-045
MDAAS-12-050
MDAAS-12-060
MDAAS-12-070
MDAAS-12-080
MDAAS-12-090
MDAAS-12-100
MDAAS-16-025
MDAAS-16-030
MDAAS-16-035
MDAAS-16-040
MDAAS-16-045
MDAAS-16-050
MDAAS-16-060
MDAAS-16-070
MDAAS-16-080
MDAAS-16-090
MDAAS-16-100
17-4 SS
Part #
MDACH-10-015
MDACH-10-020
MDACH-10-025
MDACH-10-030
MDACH-10-035
MDACH-10-040
MDACH-10-045
MDACH-10-050
MDACH-10-060
MDACH-10-070
MDACH-10-080
MDACH-10-090
MDACH-10-100
MDACH-12-020
MDACH-12-025
MDACH-12-030
MDACH-12-035
MDACH-12-040
MDACH-12-045
MDACH-12-050
MDACH-12-060
MDACH-12-070
MDACH-12-080
MDACH-12-090
MDACH-12-100
MDACH-16-025
MDACH-16-030
MDACH-16-035
MDACH-16-040
MDACH-16-045
MDACH-16-050
MDACH-16-060
MDACH-16-070
MDACH-16-080
MDACH-16-090
MDACH-16-100
mm
5
6
8
10
12
16
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
15.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
15.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
19
19
19
19
19
19
19
19
19
19
19
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
D
mm
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
46.7
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
16.1
16.0
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
23.9
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
9,207
F
mm
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9
27.9

4130 Steel
21,600
31,686
56,712
88,977
128,050
228,602
G
mm
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
33
33
33
33
33
33
33
33
33
33
33
33
42.7
42.7
42.7
42.7
42.7
42.7
42.7
42.7
42.7
42.7
42.7
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
257,179
H
mm
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
35
MA MODIFICATIONS
AVAILABLE
Stainless Dome Handle | Inch

Dia
Hole Size
Min. Pull-Out
Strength (lbs)
17-4
300 Series SS*
Max Min
Stainless
Stainless
3/16 .1940 .1900
200
5,150
1/4 .2540 .2500

230
9,200
2,200
5/16 .3165 .3125
510
14,400
3,500
3/8 .3790 .3750
575
20,600
4,500
1/2 .5050 .5000
1,160
36,800
11,500
two types of stainless steel to meet your application. Handle has hole for optional wire lanyard attachment. The handles and dome actuator buttons for the pins listed
below are made from 303 stainless steel. The large ergonomic dome actuator button facilitates easy installation and removal of the pin. They are ideal in applications
where there is repetitive or frequent use of the pin. In addition, they can be used in situations where the operator is wearing gloves or has limited range of hand motion.
They also add a unique look and feel that is not available with other pin styles and offer a large area for engraving or stamping to add logos, instructions, etc. For
specific application requirements, custom modifications are available for this product line. See page 3 for complete specifications.
17-4 SS
Part #
DCCH-18-050
DCCH-18-075
DCCH-18-100
DCCH-18-125
DCCH-18-150
DCCH-18-175
DCCH-18-200
DCCH-18-250
DCCH-18-300
DCCH-18-350
DCCH-18-400
DCCH-25-050
DCCH-25-075
DCCH-25-100
DCCH-25-125
DCCH-25-150
DCCH-25-175
DCCH-25-200
DCCH-25-250
DCCH-25-300
DCCH-25-350
DCCH-25-400
DCCH-31-050
DCCH-31-075
DCCH-31-100
DCCH-31-125
DCCH-31-150
DCCH-31-175
DCCH-31-200
DCCH-31-250
DCCH-31-300
DCCH-31-350
DCCH-31-400
36
300 Series SS
Part #
DCCS-25-050
DCCS-25-075
DCCS-25-100
DCCS-25-125
DCCS-25-150
DCCS-25-175
DCCS-25-200
DCCS-25-250
DCCS-25-300
DCCS-25-350
DCCS-25-400
DCCS-31-050
DCCS-31-075
DCCS-31-100
DCCS-31-125
DCCS-31-150
DCCS-31-175
DCCS-31-200
DCCS-31-250
DCCS-31-300
DCCS-31-350
DCCS-31-400
Nominal
Diameter
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
A
Max
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.1885
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.2485
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
.3110
A
Min
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.1870
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.2470
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
.3095
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
+/-.005
B
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.220
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.289
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
.375
+.000/-.030
C
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.260
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.290
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
.330
D
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
E
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
.47
F
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
.63
G
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
H
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
.81
MA MODIFICATIONS
AVAILABLE
Stainless Dome Handle | Inch (continued)

Dia
Hole Size
Min. Pull-Out
Strength (lbs)
17-4
300 Series SS*
Max Min
Stainless
Stainless
3/16 .1940 .1900
200
5,150
1/4 .2540 .2500

230
9,200
2,200
5/16 .3165 .3125
510
14,400
3,500
3/8 .3790 .3750
575
20,600
4,500
1/2 .5050 .5000
1,160
36,800
11,500
17-4 SS
Part #
DCCH-37-050
DCCH-37-075
DCCH-37-100
DCCH-37-125
DCCH-37-150
DCCH-37-175
DCCH-37-200
DCCH-37-250
DCCH-37-300
DCCH-37-350
DCCH-37-400
DCCH-50-100
DCCH-50-125
DCCH-50-150
DCCH-50-175
DCCH-50-200
DCCH-50-250
DCCH-50-300
DCCH-50-350
DCCH-50-400
DCCH-50-450
DCCH-50-500
DCCH-50-550
DCCH-50-600
300 Series SS
Part #
DCCS-37-050
DCCS-37-075
DCCS-37-100
DCCS-37-125
DCCS-37-150
DCCS-37-175
DCCS-37-200
DCCS-37-250
DCCS-37-300
DCCS-37-350
DCCS-37-400
DCCS-50-100
DCCS-50-125
DCCS-50-150
DCCS-50-175
DCCS-50-200
DCCS-50-250
DCCS-50-300
DCCS-50-350
DCCS-50-400
DCCS-50-450
DCCS-50-500
DCCS-50-550
DCCS-50-600
Nominal
Diameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
A
Max
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.3735
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
.4985
A
Min
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.3720
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
.4970
Grip
Length
.50
.75
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
+/-.005
B
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.440
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
.594
+.000/-.030
C
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.365
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
.460
D
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.41
E
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.56
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
.72
F
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.70
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
.85
G
.93
.93
.93
.93
.93
.93
.93
.93
.93
.93
.93
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
H
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
37
MA MODIFICATIONS
AVAILABLE
Stainless Dome Handle | Metric

Dia
mm
5
6
8
10
12
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
Calculated
Double Shear (N)
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or removed into or out of a hole. The shanks are made
from 17-4PH stainless steel. Handle has hole for optional wire lanyard attachment. The handles and dome actuator buttons for the pins listed below are made from 303
stainless steel. The large ergonomic dome actuator button facilitates easy installation and removal of the pin. They are ideal in applications where there is repetitive or
frequent use of the pin. In addition, they can be used in situations where the operator is wearing gloves or has limited range of hand motion. They also add a unique look
and feel that is not available with other pin styles and offer a large area for engraving or stamping to add logos, instructions, etc. For specific application requirements,
custom modifications are available for this product line. See page 3 for complete specifications. RoHS compliant.
17-4 SS
Part #
MDCCH-05-010
MDCCH-05-015
MDCCH-05-020
MDCCH-05-025
MDCCH-05-030
MDCCH-05-035
MDCCH-05-040
MDCCH-05-045
MDCCH-05-050
MDCCH-05-060
MDCCH-05-070
MDCCH-05-080
MDCCH-05-090
MDCCH-05-100
MDCCH-06-010
MDCCH-06-015
MDCCH-06-020
MDCCH-06-025
MDCCH-06-030
MDCCH-06-035
MDCCH-06-040
MDCCH-06-045
MDCCH-06-050
MDCCH-06-060
MDCCH-06-070
MDCCH-06-080
MDCCH-06-090
MDCCH-06-100
MDCCH-08-010
MDCCH-08-015
MDCCH-08-020
MDCCH-08-025
MDCCH-08-030
MDCCH-08-035
MDCCH-08-040
MDCCH-08-045
MDCCH-08-050
MDCCH-08-060
MDCCH-08-070
MDCCH-08-080
MDCCH-08-090
MDCCH-08-100
38
Nominal
Diameter
mm
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
A
Max
mm
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
4.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
5.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
7.96
A
Min
mm
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
4.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
7.92
Grip
Length
mm
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
10
15
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
5.54
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
6.99
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
9.42
+/-1.0
C
mm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
D
mm
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
E
mm
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
11.9
F
mm
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
G
mm
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
H
mm
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
MA MODIFICATIONS
AVAILABLE
Stainless Dome Handle | Metric (continued)

Dia
mm
5
6
8
10
12
17-4 SS
Part #
MDCCH-10-015
MDCCH-10-020
MDCCH-10-025
MDCCH-10-030
MDCCH-10-035
MDCCH-10-040
MDCCH-10-045
MDCCH-10-050
MDCCH-10-060
MDCCH-10-070
MDCCH-10-080
MDCCH-10-090
MDCCH-10-100
MDCCH-12-020
MDCCH-12-025
MDCCH-12-030
MDCCH-12-035
MDCCH-12-040
MDCCH-12-045
MDCCH-12-050
MDCCH-12-060
MDCCH-12-070
MDCCH-12-080
MDCCH-12-090
MDCCH-12-100
Nominal
Diameter
mm
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
A
Max
mm
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
9.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
11.96
A
Min
mm
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
9.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
11.92
Grip
Length
mm
15
20
25
30
35
40
45
50
60
70
80
90
100
20
25
30
35
40
45
50
60
70
80
90
100
+/-0.25
B
mm
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
11.86
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
14.45
+/-1.0
C
mm
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
D
mm
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
28.4
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
35.9
E
mm
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
14.2
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
18.3
F
mm
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
17.8
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
21.6
G
mm
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
23.6
33
33
33
33
33
33
33
33
33
33
33
33
Hole Size
Max Min
mm
mm
5.1
5.0
6.1
6.0
8.1
8.0
10.1
10.0
12.1
12.0
Min. Pull-Out
Strength (N)
890
1,023
2,268
2,558
5,160
Calculated
Double Shear (N)
17-4 Stainless
24,400
35,640
63,804
100,101
144,060
H
mm
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
34.7
39
BALL LOCK PIN FLANGE RECEPTACLES
Diamond
Oblong
Rectangle
Round
The flanged receptacles provide a permanent and proper mating hole for quick release ball lock pins. They are designed for use on materials and in applications where
the pin does not have anything to lock against. Because the pin does not protrude through the bottom of the receptacles, they are ideal for blind-hole applications. The
receptacles can be mounted with screws, rivets or bolts. They are made from 303 stainless steel. The Grip Length Reduction is the amount of pin that is inside the
receptacle and reducing the useable length of the pin by this amount. The quick release ball lock pins are inserted from the flanged end.
INCH
Part #
DIFR-187
DIFR-250
DIFR-312
DIFR-375
DIFR-500
OBFR-187
OBFR-250
OBFR-312
OBFR-375
OBFR-500
REFR-187
REFR-250
REFR-312
REFR-375
ROFR-187
ROFR-250
ROFR-312
ROFR-375
ROFR-500
For Use
With Pin
Diameter
3/16
1/4
5/16
3/8
1/2
3/16
1/4
5/16
3/8
1/2
3/16
1/4
5/16
3/8
3/16
1/4
5/16
3/8
1/2
Flange
Style
Diamond
Diamond
Diamond
Diamond
Diamond
Oblong
Oblong
Oblong
Oblong
Oblong
Rectangle
Rectangle
Rectangle
Rectangle
Round
Round
Round
Round
Round
+.000/
-.005
A
.650
.650
.783
.913
1.195
.650
.650
.783
.913
1.195
.650
.650
.783
.913
.650
.650
.783
.913
1.195
+/-.005
B
.375
.375
.469
.562
.750
.375
.375
.469
.562
.750
.375
.375
.469
.562
.375
.375
.469
.562
.750
+/-.005
C
.060
.060
.060
.060
.100
.060
.060
.060
.060
.100
.060
.060
.060
.060
.060
.060
.060
.060
.100
+/-.005
D
1.000
1.000
1.000
1.000
1.125
1.000
1.000
1.000
1.000
1.125
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.125
+/-.010
E
.625
.625
.625
.625
.875
.625
.625
.625
.625
.875
.625
.625
.625
.625
F
6-32
6-32
6-32
6-32
10-32
6-32
6-32
6-32
6-32
10-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
10-32
+/-.010
G
1.250
1.250
1.250
1.250
1.500
1.250
1.250
1.250
1.250
1.500
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.250
1.500
Grip Length
Reduction
.375
.375
.500
.562
.750
.375
.375
.500
.562
.750
.375
.375
.500
.562
.375
.375
.500
.562
.750
Flange
Style
Diamond
Diamond
Diamond
Diamond
Diamond
Oblong
Oblong
Oblong
Oblong
Oblong
Rectangle
Rectangle
Rectangle
Rectangle
Round
Round
Round
Round
Round
+0.00/
-0.13
A
mm
16.51
16.51
19.89
23.19
30.35
16.51
16.51
19.89
23.19
30.35
16.51
16.51
19.89
23.19
16.51
16.51
19.89
23.19
30.35
+/-0.13
B
mm
9.53
9.53
11.91
14.29
19.05
9.53
9.53
11.91
14.29
19.05
9.53
9.53
11.91
14.29
9.53
9.53
11.91
14.29
19.05
+/-0.13
C
mm
1.52
1.52
1.52
1.52
2.54
1.52
1.52
1.52
1.52
2.54
1.52
1.52
1.52
1.52
1.52
1.52
1.52
1.52
2.54
+/-0.13
D
mm
25
25
25
25
29
25
25
25
25
29
25
25
25
25
25
25
25
25
29
+/-0.25
E
mm
15.88
15.88
15.88
15.88
22.23
15.88
15.88
15.88
15.88
22.23
15.88
15.88
15.88
15.88
F
mm
M4
M4
M4
M4
M5
M4
M4
M4
M4
M5
M4
M4
M4
M4
M4
M4
M4
M4
M5
+/-0.25
G
mm
31.75
31.75
31.75
31.75
38.10
31.75
31.75
31.75
31.75
38.10
31.75
31.75
31.75
31.75
31.75
31.75
31.75
31.75
38.10
Grip Length
Reduction
mm
10
10
13
15
20
10
10
13
15
20
10
10
13
15
10
10
13
15
20
METRIC
Part#
MDIFR-05
MDIFR-06
MDIFR-08
MDIFR-10
MDIFR-12
MOBFR-05
MOBFR-06
MOBFR-08
MOBFR-10
MOBFR-12
MREFR-05
MREFR-06
MREFR-08
MREFR-10
MROFR-05
MROFR-06
MROFR-08
MROFR-10
MROFR-12
40
For Use
With Pin
Diameter
5mm
6mm
8mm
10mm
12mm
5mm
6mm
8mm
10mm
12mm
5mm
6mm
8mm
10mm
5mm
6mm
8mm
10mm
12mm
BALL LOCK PIN END CAPS
These end caps fit over the end of the quick release ball lock pin and allow the pins to be used in applications where the receiving hole is not within tolerance or is out
of round. The receiver caps can replace cotter pins and hitch pins to allow you to take advantage of quick changing and fieldwork without tools. The caps are made
from 303 stainless steel. The Grip Length Reduction is the amount of pin that is inside the end cap which reduces the useable length of the pin by this amount. The end
caps with the tapped ends allow the user to attach a lanyard to the end cap so it does not get lost while not in use. A stainless button head cap screw is included with
the tapped hole style.
INCH
Plain End
Part #
RC-187
RC-250
RC-312
RC-375
RC-500
RC-625
Tapped End
Part #
RCT-187
RCT-250
RCT-312
RCT-375
RCT-500
RCT-625
For Use
With Pin
Diameter
3/16
1/4
5/16
3/8
1/2
5/8
A
Diameter
.375
.375
.500
.563
.750
1.000
B
Length
.580
.580
.625
.730
1.000
1.250
C*
Screw
Depth
.12
.12
.12
.18
.18
.18
D
Thread
10-32
10-32
10-32
10-32
10-32
1/4-28
Grip
Length
Reduction
.125
.125
.125
.187
.250
.250
For Use
With Pin
Diameter
5mm
6mm
8mm
10mm
12mm
16mm
A
Diameter
mm
9.53
9.53
12.70
14.29
19.05
25.40
B
Length
mm
14.73
14.73
15.88
18.54
25.40
31.75
C*
Screw
Depth
mm
3
3
3
4
4
5
D
Thread
mm
M5
M5
M5
M5
M5
M6
Grip
Length
Reduction
mm
3
3
3
5
6
6
* Maximum Screw Depth

METRIC
Plain End
Part #
MRC-05
MRC-06
MRC-08
MRC-10
MRC-12
MRC-16
Tapped End
Part #
MRCT-05
MRCT-06
MRCT-08
MRCT-10
MRCT-12
MRCT-16
* Maximum Screw Depth
How To Use
How To Use
41
WIRE ROPE LANYARD ASSEMBLIES
MA MODIFICATIONS
AVAILABLE
Wire Rope Lanyard Assembly Specifications
Wire Rope:
Tab Styles
Rectangular Stainless
Tab
R20 (A =.20)
R28 (A =.28)
Rectangular Aluminum
Tab
RA13 (A=.13)
RA20 (A=.20)
Teardrop Stainless
Tab
T13 (A=.13)
T20 (A =.20)
T28 (A =.28)
7x7 Stainless Steel Wire

(RR-W-410)
Covering:
Vinyl (MIL-I-631)
Covered Wire Sizes:
3/64" Wire Covering to 1/16"

1/16" Wire Covering to 1/8"
Rated Strength with Tabs:
3/64" Wire = 270 lbs.

1/16" Wire = 480 lbs.
Rated Strength with Eyelets:
30 lbs.
Sleeves:
Copper - Zinc Plated (MIL-51844)

Stainless Steel (MIL-51844)
Tabs: R20, R28, T13, T20, T28
300 Series Stainless Steel

(ASTM AA240/A666)
Tabs: RA13, RA20
2024 T3/T4 Aluminum,

Clear Anodized Finish
Eyelets: E20
300 Series Stainless Steel
Wire rope lanyard assemblies are used to attach quick release pins to a fixture or frame, to prevent the pins from being misplaced while they are not in use. All of the
wire rope lanyard assemblies listed below are supplied with 7 x 7 stainless steel wire and are available either uncovered (bare cable) or covered. The vinyl covered
assemblies are available in either clear, black, or green and have a temperature range of -30/+180F. Tabs are available in both 300 series stainless steel and aluminum.
The eyelets are manufactured from 300 series stainless steel. The assemblies are available with either zinc-plated or stainless sleeves. For specific application
requirements, custom modifications are available for this product line. To order loop-tab parts, add desired tab style to part number. Sample LCL-3-06-R20.
Loop Tab
ZINC-PLATED SLEEVES
Clear
Part #
LCL-3-06-*
LCL-3-08-*
LCL-3-10-*
LCL-3-12-*
LCL-1-06-*
LCL-1-08-*
LCL-1-10-*
LCL-1-12-*
Black
Part #
LBK-3-06-*
LBK-3-08-*
LBK-3-10-*
LBK-3-12-*
LBK-1-06-*
LBK-1-08-*
LBK-1-10-*
LBK-1-12-*
Green
Part #
LGR-3-06-*
LGR-3-08-*
LGR-3-10-*
LGR-3-12-*
LGR-1-06-*
LGR-1-08-*
LGR-1-10-*
LGR-1-12-*
Uncovered
Part #
LNC-3-06-*
LNC-3-08-*
LNC-3-10-*
LNC-3-12-*
LNC-1-06-*
LNC-1-08-*
LNC-1-10-*
LNC-1-12-*
Wire
Diameter
3/64
3/64
3/64
3/64
1/16
1/16
1/16
1/16
Wire
Length
6
8
10
12
6
8
10
12
Tab
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
Green
Part #
LGRC3-06*
LGRC3-08*
LGRC3-10*
LGRC3-12*
LGRC1-06*
LGRC1-08*
LGRC1-10*
LGRC1-12*
Uncovered
Part #
LNCC3-06*
LNCC3-08*
LNCC3-10*
LNCC3-12*
LNCC1-06*
LNCC1-08*
LNCC1-10*
LNCC1-12*
Wire
Diameter
3/64
3/64
3/64
3/64
1/16
1/16
1/16
1/16
Wire
Length
6
8
10
12
6
8
10
12
Tab
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
R20 / R28 / RA13 / RA20 / T13 / T20 / T28
* Add the desired tab style.

STAINLESS STEEL SLEEVES
Clear
Part #
LCLC3-06*
LCLC3-08*
LCLC3-10*
LCLC3-12*
LCLC1-06*
LCLC1-08*
LCLC1-10*
LCLC1-12*
Black
Part #
LBKC3-06*
LBKC3-08*
LBKC3-10*
LBKC3-12*
LBKC1-06*
LBKC1-08*
LBKC1-10*
LBKC1-12*
* Add the desired tab style.
42
WIRE ROPE LANYARD ASSEMBLIES (cont.)
MA MODIFICATIONS
AVAILABLE
Loop Eyelet
ZINC-PLATED SLEEVES
Clear
Black
Part #
Part #
LCL-3-06-E20
LBK-3-06-E20
LCL-3-08-E20
LBK-3-08-E20
LCL-3-10-E20
LBK-3-10-E20
LCL-3-12-E20
LBK-3-12-E20
LCL-1-06-E20
LBK-1-06-E20
LCL-1-08-E20
LBK-1-08-E20
LCL-1-10-E20
LBK-1-10-E20
LCL-1-12-E20
LBK-1-12-E20
Green
Part #
LGR-3-06-E20
LGR-3-08-E20
LGR-3-10-E20
LGR-3-12-E20
LGR-1-06-E20
LGR-1-08-E20
LGR-1-10-E20
LGR-1-12-E20
Uncovered
Part #
LNC-3-06-E20
LNC-3-08-E20
LNC-3-10-E20
LNC-3-12-E20
LNC-1-06-E20
LNC-1-08-E20
LNC-1-10-E20
LNC-1-12-E20
Wire
Diameter
3/64
3/64
3/64
3/64
1/16
1/16
1/16
1/16
Wire
Length
6
8
10
12
6
8
10
12
A
.33
.33
.33
.33
.41
.41
.41
.41
B
.04
.04
.04
.04
.06
.06
.06
.06
Eyelet
Hole Size
.20
.20
.20
.20
.20
.20
.20
.20

Clear
Black
Part #
Part #
LCLC3-06E20
LBKC3-06E20
LCLC3-08E20
LBKC3-08E20
LCLC3-10E20
LBKC3-10E20
LCLC3-12E20
LBKC3-12E20
LCLC1-06E20
LBKC1-06E20
LCLC1-08E20
LBKC1-08E20
LCLC1-10E20
LBKC1-10E20
LCLC1-12E20
LBKC1-12E20
Green
Part #
LGRC3-06E20
LGRC3-08E20
LGRC3-10E20
LGRC3-12E20
LGRC1-06E20
LGRC1-08E20
LGRC1-10E20
LGRC1-12E20
Uncovered
Part #
LNCC3-06E20
LNCC3-08E20
LNCC3-10E20
LNCC3-12E20
LNCC1-06E20
LNCC1-08E20
LNCC1-10E20
LNCC1-12E20
Wire
Diameter
3/64
3/64
3/64
3/64
1/16
1/16
1/16
1/16
Wire
Length
6
8
10
12
6
8
10
12
A
.33
.33
.33
.33
.41
.41
.41
.41
B
.04
.04
.04
.04
.06
.06
.06
.06
Eyelet
Hole Size
.20
.20
.20
.20
.20
.20
.20
.20
Loop Loop
ZINC-PLATED SLEEVES
Clear
Black
Part #
Part #
LCL-3-06
LBK-3-06
LCL-3-08
LBK-3-08
LCL-3-10
LBK-3-10
LCL-3-12
LBK-3-12
LCL-1-06
LBK-1-06
LCL-1-08
LBK-1-08
LCL-1-10
LBK-1-10
LCL-1-12
LBK-1-12
Green
Part #
LGR-3-06
LGR-3-08
LGR-3-10
LGR-3-12
LGR-1-06
LGR-1-08
LGR-1-10
LGR-1-12
Uncovered
Part #
LNC-3-06
LNC-3-08
LNC-3-10
LNC-3-12
LNC-1-06
LNC-1-08
LNC-1-10
LNC-1-12
Wire
Diameter
3/64
3/64
3/64
3/64
1/16
1/16
1/16
1/16
Wire
Length
6
8
10
12
6
8
10
12

Clear
Black
Part #
Part #
LCLC3-06
LBKC3-06
LCLC3-08
LBKC3-08
LCLC3-10
LBKC3-10
LCLC3-12
LBKC3-12
LCLC1-06
LBKC1-06
LCLC1-08
LBKC1-08
LCLC1-10
LBKC1-10
LCLC1-12
LBKC1-12
Green
Part #
LGRC3-06
LGRC3-08
LGRC3-10
LGRC3-12
LGRC1-06
LGRC1-08
LGRC1-10
LGRC1-12
Uncovered
Part #
LNCC3-06
LNCC3-08
LNCC3-10
LNCC3-12
LNCC1-06
LNCC1-08
LNCC1-10
LNCC1-12
Wire
Diameter
3/64
3/64
3/64
3/64
1/16
1/16
1/16
1/16
Wire
Length
6
8
10
12
6
8
10
12
Split Rings
Used for attaching ball lock pins to a lanyard. Prevents the pin from being lost when not in use. Made from 302 stainless steel.
Part #
RSC-37
D
.962
D1
.072
43
PULL PINS
T-Handle
Round Handle
Threaded
These spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations. They consist of two parts which
include a housing (barrel) and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling
on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. The lockout style allows
you to pull and rotate the handle 1/4 turn to hold the plunger in the retracted position. The style without handles feature a 3/8-16 threaded end so the user can add a
different handle or other method of actuation. The zinc plated steel plunger assemblies are made from C1038 steel on all sizes except the 5/8 which is made from 12L15
steel. The steel housing is made from 12L15 steel for welding to the fixture and is not plated. The aluminum housings are made from 6061-T6. The stainless steel models
(plunger assembly and housing) are made from 303 stainless steel. Pull up force is approximately 5 lbs. Handles are made from black plastic.
T-HANDLE - NON-LOCKING
Steel Plunger
Steel Plunger
Steel Housing
Alum Housing
Part #
Part #
CP-K25T
CP-K25TAL
CP-K100T
CP-K100TAL
CP-K200T
CP-K200TAL
CP-K320T
CP-K320TAL
CP-K420T
CP-K420TAL
SS Plunger
SS Housing
Part #
CP-K100TSS
CP-K200TSS
CP-K320TSS
+.012
-.010
A
1/4
3/8
1/2
1/2
5/8
T-HANDLE - WITH LOCKOUT

Steel Plunger
Steel Plunger
Steel Housing
Alum Housing
Part #
Part #
CP-K25TLO
CP-K25TLOAL
CP-K100TLO
CP-K100TLOAL
CP-K200TLO
CP-K200TLOAL
CP-K320TLO
CP-K320TLOAL
CP-K420TLO
CP-K420TLOAL
SS Plunger
SS Housing
Part #
CP-K100TLOSS
CP-K200TLOSS
CP-K320TLOSS
+.012
-.010
A
1/4
3/8
1/2
1/2
5/8
ROUND HANDLE - NON-LOCKING

Steel Plunger
Steel Plunger
Steel Housing
Alum Housing
Part #
Part #
CP-K25R
CP-K25RAL
CP-K100R
CP-K100RAL
CP-K200R
CP-K200RAL
CP-K320R
CP-K320RAL
CP-K420R
CP-K420RAL
SS Plunger
SS Housing
Part #
CP-K100RSS
CP-K200RSS
CP-K320RSS
+.012
-.010
A
1/4
3/8
1/2
1/2
5/8
ROUND HANDLE - WITH LOCKOUT

Steel Plunger
Steel Plunger
Steel Housing
Alum Housing
Part #
Part #
CP-K25RLO
CP-K25RLOAL
CP-K100RLO
CP-K100RLOAL
CP-K200RLO
CP-K200RLOAL
CP-K320RLO
CP-K320RLOAL
CP-K420RLO
CP-K420RLOAL
SS Plunger
SS Housing
Part #
CP-K100RLOSS
CP-K200RLOSS
CP-K320RLOSS
+.012
-.010
A
1/4
3/8
1/2
1/2
5/8
THREADED END - NON-LOCKING

Steel Plunger
Steel Plunger
SS Plunger
Steel Housing
Alum Housing
SS Housing
Part #
Part #
Part #
CP-K25NK
CP-K25NKAL
CP-K100NK
CP-K100NKAL
CP-K100NKSS
CP-K200NK
CP-K200NKAL
CP-K200NKSS
CP-K320NK
CP-K320NKAL
CP-K320NKSS
CP-K420NK
CP-K420NKAL
44
B
9/16
9/16
9/16
9/16
9/16
B
9/16
9/16
9/16
9/16
9/16
B
9/16
9/16
9/16
9/16
9/16
B
9/16
9/16
9/16
9/16
9/16
C
1-1/2
1-1/2
1-1/2
2-1/4
2-1/4
+.000
-.005
D
1.000
1.000
1.000
1.000
1.000
E
3/16
3/16
3/16
3/16
3/16
F
1-7/16
1-7/16
1-7/16
1-7/16
1-7/16
G
2-1/4
2-1/4
2-1/4
2-1/4
2-1/4
C
1-1/2
1-1/2
1-1/2
2-1/4
2-1/4
+.000
-.005
D
1.000
1.000
1.000
1.000
1.000
E
3/16
3/16
3/16
3/16
3/16
F
1-7/16
1-7/16
1-7/16
1-7/16
1-7/16
G
2-1/4
2-1/4
2-1/4
2-1/4
2-1/4
C
1-1/2
1-1/2
1-1/2
2-1/4
2-1/4
+.000
-.005
D
1.000
1.000
1.000
1.000
1.000
E
3/16
3/16
3/16
3/16
3/16
F
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
C
1-1/2
1-1/2
1-1/2
2-1/4
2-1/4
+.000
-.005
D
1.000
1.000
1.000
1.000
1.000
E
3/16
3/16
3/16
3/16
3/16
F
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
HOUSINGS ONLY
+.012
-.010
A
1/4
3/8
1/2
1/2
5/8
B
9/16
9/16
9/16
9/16
9/16
C
1-1/2
1-1/2
1-1/2
2-1/4
2-1/4
+.000
-.005
D
1.000
1.000
1.000
1.000
1.000
E
3/16
3/16
3/16
3/16
3/16
Steel Housing
Part #
CP-K102-BO
CP-K102L-BO
Alum Housing
Part #
CP-K102AL-BO
CP-K102LAL-BO
SS Housing
Part #
CP-K102SS-BO
CP-K102LSS-BO
Internal
Thread
3/4-10
3/4-10
Length
1-1/2
2-1/4
Doing Business with Fairlane Products

Purchasing From Fairlane Products
All items listed in this catalog are sold through a network of
approved distributors. Original Equipment Manufacturers (OEM)
may be able to purchase directly based on quantity, item and
other criteria. Please call us at 586-294-6100 for assistance with
any questions about purchasing or locating a distributor.
Website
Our website at www.fairlaneproducts.com was developed to
allow users easy access to a full array of services. Within our
website you can easily search our entire product line for the exact
part to fit your application. Full product information including
materials, dimension and other technical data is available. In
addition, CAD models can be viewed and downloaded in a variety
of formats so you can integrate the parts directly into your CAD
database or projects.
Business Hours
Representatives are available to assist you from 8:00 a.m. to
4:30 p.m. Eastern Time, Monday through Friday.
Preisgestaltung
OEM quantity price discounts are available for many items and
apply to the quantity of each specific part. We do our best to hold
pricing, however, any published prices are subject to change
without notice. Quoted prices will be valid for 30 days.
Shipments
All items in this catalog are normally stocked. Backordered parts
are always given a high priority and will ship as soon as they
become available. For OEM customers, normal shipment is UPS
FOB Fraser Michigan unless otherwise noted. Shipping charges
are prepaid and added to the invoice. Special charges and
guidelines apply to shipments outside the United States. Buyers
are responsible for all applicable taxes and duties on international
shipments.
Material Data Safety Sheets

Material Data Safety Sheets are available upon request.
Specifications
We do our best to represent our products as accurately as
possible in both our catalogs and website, however, all
specifications are subject to change without notice.
Choice of Law
The terms of sale for purchases from Fairlane Products shall be
governed by and construed in accordance with the laws of the
State of Michigan as applied to contracts made and to be
performed in Michigan. Any action arising out of such purchases
must be brought in courts in Michigan. Purchasers consent to the
jurisdiction of the courts in Michigan and to service of process by
registered mail, return receipt requested, or by other manner
proved by law.
Entire Agreement
By placement of an order or by acceptance of goods ordered,
buyer signifies agreement that no terms, conditions or warranties
other than those stated here, and no agreement or understanding,
oral or written, in any way purporting to modify these terms,
conditions and or warranties, whether contained in buyers
purchase order or elsewhere, shall be binding on Fairlane
Products.
Customer Comments
Everyone at Fairlane Products takes great pride in their work and
truly strives for complete customer satisfaction. If you ever have
any comments or suggestions on our products, service, catalogs
or website, please let us know. They are appreciated and taken
seriously.
Returns
An RGA number must be issued before returning any products. All
returns must be shipped via UPS and reference the RGA number
on the outside of the box. Custom products cannot be returned.
Custom Products
Some products may be modified to meet your exact
specifications. Please inquire for pricing. Once custom made
products are in process, the order may not be cancelled. Custom
made products cannot be returned.
45

Fairlane Pins

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fairlane Pins

Uploaded by

Copyright:

Available Formats

INDEX

End Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Button Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-19

Wire Lanyards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42-43

Ring Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-27

Pull Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Nautical Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-31

Dome Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-39

QUICK RELEASE BALL LOCK PINS

Selecting the proper Quick Release Ball Lock Pin

2. Select the proper grip length.

The grip length (also referred to as the useable length) is

3. Select the proper shank material.

4. Select the proper handle style.

5. Select lanyard assembly.

QUICK RELEASE BALL LOCK PINS

300 SERIES SS PINS

CRES 17-4PH (Stainless Steel)

STEEL ALLOY 4130 PINS

Aluminum 380 Die Cast

Hole Size / Performance Data

Calculated Double Shear (lbs)

Calculated Double Shear (N)

QUICK RELEASE BALL LOCK PINS

Calculated Double Shear (lbs)

17-4 Stainless 300 Series SS*

QUICK RELEASE BALL LOCK PINS

T-Handle | Inch (continued)

Calculated Double Shear (lbs)

17-4 Stainless 300 Series SS*

QUICK RELEASE BALL LOCK PINS

Calculated Double Shear (N)

QUICK RELEASE BALL LOCK PINS

T-Handle | Metric (continued)

Calculated Double Shear (N)

QUICK RELEASE BALL LOCK PINS

Calculated Double Shear (lbs)

17-4 Stainless 300 Series SS*

QUICK RELEASE BALL LOCK PINS

L-Handle | Inch (continued)

Calculated Double Shear (lbs)

17-4 Stainless 300 Series SS*

QUICK RELEASE BALL LOCK PINS

Calculated Double Shear (N)

QUICK RELEASE BALL LOCK PINS

L-Handle | Metric (continued)

Calculated Double Shear (N)

QUICK RELEASE BALL LOCK PINS

Aluminum Button Handle | Inch

Calculated Double Shear (lbs)

QUICK RELEASE BALL LOCK PINS

Aluminum Button Handle | Inch (continued)

Calculated Double Shear (lbs)

QUICK RELEASE BALL LOCK PINS

Aluminum Button Handle | Metric

Calculated Double Shear (N)

QUICK RELEASE BALL LOCK PINS

Aluminum Button Handle | Metric (continued)

Calculated Double Shear (N)

QUICK RELEASE BALL LOCK PINS

Stainless Steel Button Handle | Inch

1/4 .2540 .2500

QUICK RELEASE BALL LOCK PINS