Professional Documents
Culture Documents
Válvula de Control Auxiliar
Válvula de Control Auxiliar
Pgina 1 de 11
Cerrar SIS
Pantalla anterior
Producto: EXCAVATOR
Modelo: 323D L EXCAVATOR SDC
Configuracin: 323D & 323D L Excavator SDC00001-UP (MACHINE)
POWERED BY 3066 Engine
Pruebas y Ajustes
320D, 320D LRR, 321D LCR, 323D, 324D, 325D, 328D LCR, 329D, 330D and 336D Excavators
Tool Control System
Nmero de medio -RENR7389-16
System 17: Relief Valve (Line) - Test and Adjust - Auxiliary Control
Valve
SMCS - 5117-036-L9
S/N - BFC1-UP
S/N - BTK1-UP
S/N - BYM1-UP
S/N - CWG1-UP
S/N - CYD1-UP
S/N - CYW1-UP
S/N - CZF1-UP
S/N - DKW1-UP
S/N - DTS1-UP
S/N - DTZ1-UP
S/N - EBM1-UP
S/N - EJC1-UP
S/N - ERN1-UP
S/N - GBC1-UP
S/N - GBR1-UP
S/N - GGE1-UP
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 2 de 11
S/N - GPB1-UP
S/N - JBF1-UP
S/N - JLG1-UP
S/N - KDJ1-UP
S/N - LAL1-UP
S/N - LRM1-UP
S/N - M4T1-UP
S/N - MCL1-UP
S/N - MKR1-UP
S/N - MYG1-UP
S/N - MYP1-UP
S/N - NDE1-UP
S/N - NES1-UP
S/N - PBD1-UP
S/N - PBM1-UP
S/N - PKE1-UP
S/N - PPN1-UP
S/N - RAC1-UP
S/N - RAS1-UP
S/N - SBZ1-UP
S/N - SCY1-UP
S/N - SDC1-UP
S/N - SED1-UP
S/N - SYM1-UP
S/N - T2D1-UP
S/N - T2S1-UP
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 3 de 11
S/N - T2Y1-UP
S/N - THJ1-UP
S/N - TPM1-UP
S/N - TRH1-UP
S/N - WET1-UP
S/N - WGC1-UP
S/N - WLT1-UP
S/N - WNE1-UP
S/N - XDB1-UP
S/N - YFW1-UP
S/N - YSD1-UP
S/N - ZMF1-UP
Test for the Line Relief Valve on the Attachment Control Valve
Note: A temporary setting of the main relief valve pressure is required before any line relief valve pressure
setting is adjusted. Refer to the temporary setting of the main relief valve pressure in Testing and Adjusting,
"Relief Valve (Main) - Test and Adjust" for the machine.
Illustration 1
g01197980
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 4 de 11
(1) Up key
(2) Right key
(3) Home key
(4) Main menu key
(5) Left key
(6) Down key
(7) Cancel key
(8) OK key
Illustration 2
Pump Compartment 320D, 323D, 324D, 325D, 328D and 329D
g01534994
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 5 de 11
Illustration 3
Pump Compartment 330D and 336D
g01240884
3. Install a pressure gauge with a 6000 kPa (870 psi) capacity on pressure tap (11) for the power shift.
4. Install a pressure gauge with a 60000 kPa (8700 psi) capacity on pressure tap (9) for the drive pump.
5. Start the engine.
6. Place the machine controls at the following settings: engine speed dial 10 and AEC switch OFF. Refer
to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the machine for engine rpm
settings.
7. Warm the hydraulic oil to 50 C (122 F).
8. Set the pilot pressure to the specifications in Testing and Adjusting, "Relief Valve (Pilot) - Test and
Adjust" for the machine.
9. Use the following procedure to access the "SERVICE" mode of the monitor.
a. From the default screen, press the main menu key (4) .
b. Use the right key (2) or the left key (5) in order to scroll through the menu options.
c. When the "SERVICE" option is highlighted, press the OK key (8) .
Note: In order to access the "SERVICE" screen, the password for service must be entered.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 6 de 11
d. When "PASSWORD" screen appears, use the right key (2) and the left key (5) in order to scroll
through the characters. When the desired character is highlighted, press the OK key (8). Enter
the password for service FFF2 in order to continue to the "SERVICE" screen.
e. After the password has been entered the "SERVICE" screen should appear. Refer to Illustration
4.
Note: For more detailed steps with entering passwords or entering the service mode, refer to
Testing and Adjusting, "Service Mode - Enter" for the Tool Control System.
Illustration 4
Typical example of the "SERVICE" menu for the monitor
g01200022
10. Use the down key (6) in order to scroll through the menu options.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 7 de 11
11. When the "DEVICE TEST" option is highlighted, press the OK key (8) .
Illustration 5
g01200028
12. After the OK key is pressed, the "DEVICE TEST" menu should appear.
13. Use the down key (6) in order to scroll through the menu options.
14. When the "POWER SHIFT PRESS" option is highlighted, press the OK key (8) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 8 de 11
Illustration 6
g01200030
15. Use the down key (6) in order to highlight the value of the power shift pressure.
16. Use the right key (2) in order to decrease the value of the power shift pressure. Use the left key (5) in
order to increase the value of the power shift pressure.
Pressing the left key (5) one time decreases the power shift pressure 10 kPa (1.5 psi). Pressing the
right key (2) one time increases the power shift pressure 10 kPa (1.5 psi).
Note: The value for power shift pressure on the monitor may not always match the pressure reading on
the pressure gauge. Adjust the value on the monitor until the desired power shift pressure is attained
on the pressure gauge that is connected to the pressure tap for power shift pressure. The actual power
shift pressure must be 2900 kPa (420 psi) on the pressure gauge.
Note: To prevent a change in power shift pressure during the adjustment of the line relief valve for the
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine(... Pgina 9 de 11
attachment control valve, do not turn the engine start switch to the OFF position.
Note: Refer to Systems Operation, "Monitoring System" for the machine for additional information on
Service Mode.
17. Set the main relief valve to specifications. Refer to Testing and Adjusting, "Relief Valve (Main) - Test
and Adjust" for the machine.
18. Calibrate the power shift pressure. Refer to Testing and Adjusting, "Calibration" for the Machine
Electronic Control System.
19. The pressure setting for the top line relief valve and for the bottom line relief valve for the attachment
control valve is 37000 1000 kPa (5350 145 psi).
Note: After relief valve adjustments, cancel Service Mode.
Note: Return the main relief valve pressure to the specified setting after testing and adjusting any line relief
valve. Refer to Testing and Adjusting, "Relief Valve (Main) - Test and Adjust" for the machine for the main
relief valve pressure setting.
Note: To prevent oil flow to the work tool during this testing and adjusting procedure, close the stop valves
in the lines for the work tool.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engi... Pgina 10 de 11
Illustration 7
Line relief valve (Typical example)
g01199900
(12) Locknut
(13) Adjustment screw
5. Loosen locknut (12) on the line relief valve for the work tool. The relief valve is located on the top
side of the main control valve. Turn adjustment screw (13) until the pressure gauge reading at pressure
tap (11) is 37000 1000 kPa (5350 145 psi).
6. To adjust the line relief valve pressure setting of the lower work tool, push the thumb wheel on the
right joystick BACKWARD. Hold the thumb wheel in this position.
7. Check the pressure in the work tool at pressure tap (11) .
8. Return the thumb wheel to the NEUTRAL position.
9. Compare the pressure reading to the specification 37000 1000 kPa (5350 145 psi). If the pressure
reading is within the specification, no further adjustment is necessary. If the pressure reading is not
within the specification, then proceed to Step 10.
10. Loosen locknut (12) on the line relief valve for the work tool. The relief valve is located on the bottom
of the main control valve. Turn adjustment screw (13) until the pressure gauge reading at pressure tap
(11) is 37000 1000 kPa (5350 145 psi).
11. After completion of line relief valve adjustment, tighten locknut (12) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engi... Pgina 11 de 11
Note: Turning adjustment screw (13) clockwise increases the pressure. Turning adjustment screw (13)
counterclockwise decreases the pressure.
Note: Always make final pressure adjustment on pressure rise.
Note: After relief valve adjustments, cancel Service Mode.
Note: Return the main relief valve pressure to the specified setting after testing and adjusting any line relief
valve. Refer to Testing and Adjusting, "Relief Valve (Main) - Test and Adjust" for the machine for the main
relief valve pressure setting.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 17/08/2014