Professional Documents
Culture Documents
OSI: Physical Layer
OSI: Physical Layer
Layer
Layer Name
Layer task
Number
7
Application
Provide platform to access network
6
Presentation
Format data
5
Session
Configure and open network connection
4
Transport
Break large data file in small segments
3
Network
Find route for IP address
2
Data Link
Pack data for transmission
1
Physical
Transmit or receive data
The physical layer of the OSI model defines connector and interface
specifications, as well as the medium (cable) requirements .Electrical, mechanical,
functional and procedural specifications are provided for sending a bit stream on a
computer network.
Sample Components
Hub
NIC
make up a Data Link layer frame. This layer accepts a complete frame from the Data Link layer
and encodes it as a series of signals that are transmitted onto the local media. The encoded bits
that comprise a frame are received by either an end device or an intermediate device.
The delivery of frames across the local media requires the following Physical layer elements:
At this stage of the communication process, the user data has been segmented by the Transport
layer, placed into packets by the Network layer, and further encapsulated as frames by the Data
Link layer. The purpose of the Physical layer is to create the electrical, optical, or
microwave signal that represents the bits in each frame. These signals are then sent on the
media one at a time. It is also the job of the Physical layer to retrieve these individual signals
from the media, restore them to their bit representations, and pass the bits up to the Data Link
layer as a complete frame.
Copper cable
Fiber
Wireless
The representation of the bits - that is, the type of signal - depends on the type of media. For
copper cable media, the signals are patterns of electrical pulses. For fiber, the signals are patterns
of light. For wireless media, the signals are patterns of radio transmissions.
Identifying a Frame
When the Physical layer encodes the bits into the signals for a particular medium, it must also
distinguish where one frame ends and the next frame begins. Otherwise, the devices on the
media would not recognize when a frame has been fully received. In that case, the destination
device would only receive a string of signals and would not be able to properly reconstruct the
frame. As described in the previous chapter, indicating the beginning of frame is often a function
of the Data Link layer. However, in many technologies, the Physical layer may add its own
signals to indicate the beginning and end of the frame. To enable a receiving device to clearly
recognize a frame boundary, the transmitting device adds signals to designate the start and end of
a frame. These signals represent particular bit patterns that are only used to denote the start or
end of a frame. The process of encoding a frame of data from the logical bits into the physical
signals on the media, and the characteristics of particular physical media, are covered in detail in
the following sections of this chapter.
Hardware components such as network adapters (NICs), interfaces and connectors, cable
materials, and cable designs are all specified in standards associated with the Physical layer.
Data encoding
Signaling
The physical elements are the electronic hardware devices, media and connectors that transmit
and carry the signals to represent the bits.
Encoding
Encoding is a method of converting a stream of data bits into a predefined code. Codes are
groupings of bits used to provide a predictable pattern that can be recognized by both the sender
and the received. Using predictable patterns helps to distinguish data bits from control bits and
provide better media error detection. In addition to creating codes for data, encoding methods at
the Physical layer may also provide codes for control purposes such as identifying the beginning
and end of a frame. The transmitting host will transmit the specific pattern of bits or a code to
identify the beginning and end of the frame.
Signaling
The Physical layer must generate the electrical, optical, or wireless signals that represent the "1"
and "0" on the media. The method of representing the bits is called the signaling method. The
Physical layer standards must define what type of signal represents a "1" and a "0". This can be
as simple as a change in the level of an electrical signal or optical pulse or a more complex
signaling method.
Signaling Methods
Bits are represented on the medium by changing one or more of the following characteristics of a
signal:
Amplitude
Frequency
Phase
The nature of the actual signals representing the bits on the media will depend on the signaling
method in use. Some methods may use one attribute of signal to represent a single 0 and use
another attribute of signal to represent a single 1. As an example, with Non-Return to Zero
(NRZ), a 0 may be represented by one voltage level on the media during the bit time and a 1
might be represented by a different voltage on the media during the bit time. There are also
methods of signaling that use transitions, or the absence of transitions, to indicate a logic level.
For example, Manchester Encoding indicates a 0 by a high to low voltage transition in the
middle of the bit time. For a 1 there is a low to high voltage transition in the middle of the bit
time. The signaling method used must be compatible with a standard so that the receiver can
detect the signals and decode them. The standard contains an agreement between the transmitter
and the receiver on how to represent 1s and 0s. If there is no signaling agreement - that is, if
different standards are used at each end of the transmission - communication across the physical
medium will fail. Signaling methods to represent bits on the media can be complex. We will look
at two of the simpler techniques to illustrate the concept.
NRZ Signaling
As a first example, we will examine a simple signaling method, Non Return to Zero (NRZ). In
NRZ, the bit stream is transmitted as a series of voltage values, as shown in the figure. A low
voltage value represents a logical 0 and a high voltage value represents a logical 1. The voltage
range depends on the particular Physical layer standard in use.
This simple method of signaling is only suited for slow speed data links. NRZ signaling uses
bandwidth inefficiently and is susceptible to electromagnetic interference. Additionally, the
boundaries between individual bits can be lost when long strings of 1s or 0s are transmitted
consecutively. In that case, no voltage transitions are detectable on the media. Therefore, the
receiving nodes do not have a transition to use in resynchronizing bit times with the transmitting
node.
Manchester Encoding
Instead of representing bits as pulses of simple voltage values, in the Manchester Encoding
scheme, bit values are represented as voltage transitions. For example, a transition from a low
voltage to a high voltage represents a bit value of 1. A transition from a high voltage to a low
voltage represents a bit value of 0. As shown in the figure, one voltage transition must occur in
the middle of each bit time. This transition can be used to ensure that the bit times in the
receiving nodes are synchronized with the transmitting node. The transition in the middle of the
bit time will be either the up or down direction for each unit of time in which a bit is transmitted.
For consecutive bit values, a transition on the bit boundary "sets up" the appropriate mid-bit time
transition that represents the bit value.
Although Manchester Encoding is not efficient enough to be used at higher signaling
speeds, it is the signaling method employed by 10BaseT Ethernet (Ethernet running at 10
Megabits per second).
Signal Patterns
One way to provide frame detection is to begin each frame with a pattern of signals representing
bits that the Physical layer recognizes as denoting the start of a frame. Another pattern of bits
will signal the end of the frame. Signal bits not framed in this manner are ignored by the Physical
layer standard being used. Valid data bits need to be grouped into a frame; otherwise, data bits
will be received without any context to give them meaning to the upper layers of the networking
model. This framing method can be provided by the Data Link layer, the Physical layer, or by
both. The figure depicts some of the purposes of signaling patterns. Signal patterns can indicate:
start of frame, end of frame, and frame contents. These signal patterns can be decoded into bits.
The bits are interpreted as codes. The codes indicate where the frames start and stop.
Code Groups
Encoding techniques use bit patterns called symbols. The Physical layer may use a set of
encoded symbols - called code groups - to represent encoded data or control information. A code
group is a consecutive sequence of code bits that are interpreted and mapped as data bit
patterns. For example, code bits 10101 could represent the data bits 0011. As shown in the
figure, code groups are often used as an intermediary encoding technique for higher speed LAN
technologies. This step occurs at the Physical layer prior to the generation of signals of voltages,
light pulses, or radio frequencies. By transmitting symbols, the error detection capabilities and
timing synchronization between transmitting and receiving devices are enhanced. These are
important considerations in supporting high speed transmission over the media. Although using
code groups introduces overhead in the form of extra bits to transmit, they improve the
robustness of a communications link. This is particularly true for higher speed data transmission.
Advantages using code groups include:
Data symbols - Symbols that represent the data of the frame as it is passed down to the
Physical layer.
Control symbols - Special codes injected by the Physical layer used to control
transmission. These include end-of-frame and idle media symbols.
Invalid symbols - Symbols that have patterns not allowed on the media. The receipt of an
invalid symbol indicates a frame error.
The symbols encoded onto the media are all unique. The symbols representing the data being
sent through the network have different bit patterns than the symbols used for control. These
differences allow the Physical layer in the receiving node to immediately distinguish data from
control information.
Better Media Error Detection
In addition to the data symbols and control symbols, code groups contain invalid symbols. These
are the symbols that could create long series of 1s or 0s on the media; therefore, they are not used
by the transmitting node. If a receiving node receives one of these patterns, the Physical layer
can determine that there has been an error in data reception.
4B/5B
An example, we will examine a simple code group called 4B/5B. Code groups that are currently
used in modern networks are generally more complex. In this technique, 4 bits of data are turned
into 5-bit code symbols for transmission over the media system. In 4B/5B, each byte to be
transmitted is broken into four-bit pieces or nibbles and encoded as five-bit values known as
symbols. These symbols represent the data to be transmitted as well as a set of codes that help
control transmission on the media. Among the codes are symbols that indicate the beginning and
end of the frame transmission. Although this process adds overhead to the bit transmissions, it
also adds features that aid in the transmission of data at higher speeds. 4B/5B ensures that there
is at least one level change per code to provide synchronization. Most of the codes used in 4B/5B
balance the number of 1s and 0s used in each symbol. As shown in the figure, 16 of the possible
32 combinations of code groups are allocated for data bits, and the remaining code groups are
used for control symbols and invalid symbols. Six of the symbols are used for special functions
identifying the transition from idle to frame data and end of stream delimiter. The remaining 10
symbols indicate invalid codes.
Bandwidth
Throughput
Goodput
Bandwidth
The capacity of a medium to carry data is described as the raw data bandwidth of the media.
Digital bandwidth measures the amount of information that can flow from one place to another
in a given amount of time. Bandwidth is typically measured in kilobits per second (kbps) or
megabits per second (Mbps). The practical bandwidth of a network is determined by a
combination of factors: the properties of the physical media and the technologies chosen for
signaling and detecting network signals. Physical media properties, current technologies, and the
laws of physics all play a role in determining available bandwidth.
Throughput
Throughput is the measure of the transfer of bits across the media over a given period of
time. Due to a number of factors, throughput usually does not match the specified bandwidth in
Physical layer implementations such as Ethernet. Many factors influence throughput. Among
these factors are the amount of traffic, the type of traffic, and the number of network devices
encountered on the network being measured. In a multi-access topology such as Ethernet, nodes
are competing for media access and its use. Therefore, the throughput of each node is degraded
as usage of the media increases. In an internetwork or network with multiple segments,
throughput cannot be faster than the slowest link of the path from source to destination. Even if
all or most of the segments have high bandwidth, it will only take one segment in the path with
low throughput to create a bottleneck to the throughput of the entire network.
Goodput
A third measurement has been created to measure the transfer of usable data. That measure is
known as goodput. Goodput is the measure of usable data transferred over a given period of
time, and is therefore the measure that is of most interest to network users. As shown in the
figure, goodput measures the effective transfer of user data between Application layer entities,
such as between a source web server process and a destination web browser device. Unlike
throughput, which measures the transfer of bits and not the transfer of usable data, goodput
accounts for bits devoted to protocol overhead. Goodput is throughput minus traffic overhead for
Copper Media
The most commonly used media for data communications is cabling that uses copper wires to
signal data and control bits between network devices. Cabling used for data communications
usually consists of a series of individual copper wires that form circuits dedicated to specific
signaling purposes. Other types of copper cabling, known as coaxial cable, have a single
conductor that runs through the center of the cable that is encased by, but insulated from, the
other shield. The copper media type chosen is specified by the Physical layer standard required
to link the Data Link layers of two or more network devices. These cables can be used to connect
nodes on a LAN to intermediate devices, such as routers and switches. Cables are also used to
connect WAN devices to a data services provider such as a telephone company. Each type of
connection and the accompanying devices have cabling requirements stipulated by Physical layer
standards. Networking media generally make use of modular jacks and plugs, which provide
easy connection and disconnection. Also, a single type of physical connector may be used for
multiple types of connections. For example, the RJ-45 connector is used widely in LANs with
one type of media and in some WANs with another media type.
Selecting the cable type or category most suited to protect the data signals in a given
networking environment
Using cabling techniques that include the proper handling and termination of the cables
but opposite forces - have a cancellation effect on each other. Additionally, the different pairs of
wires that are twisted in the cable use a different number of twists per meter to help protect the
cable from crosstalk between pairs.
UTP Cabling Standards
The UTP cabling commonly found in workplaces, schools, and homes conforms to the standards
established jointly by the Telecommunications Industry Association (TIA) and the Electronics
Industries Alliance (EIA). TIA/EIA-568A stipulates the commercial cabling standards for LAN
installations and is the standard most commonly used in LAN cabling environments. Some of the
elements defined are:
Cable types
Cable lengths
Connectors
Cable termination
The electrical characteristics of copper cabling are defined by the Institute of Electrical and
Electronics Engineers (IEEE). IEEE rates UTP cabling according to its performance. Cables are
placed into categories according to their ability to carry higher bandwidth rates. For example,
Category 5 (Cat5) cable is used commonly in 100BASE-TX FastEthernet installations. Other
categories include Enhanced Category 5 (Cat5e) cable and Category 6 (Cat6). Cables in higher
categories are designed and constructed to support higher data rates. As new gigabit speed
Ethernet technologies are being developed and adopted, Cat5e is now the minimally acceptable
cable type, with Cat6 being the recommended type for new building installations. Some people
connect to data network using existing telephone systems. Often the cabling in these systems are
some form of UTP that are lower grade than the current Cat5+ standards. Installing less
expensive but lower rated cabling is potentially wasteful and shortsighted. If the decision is later
made to adopt a faster LAN technology, total replacement of the installed cable infrastructure
may be required.
Ethernet Straight-through
Ethernet Crossover
Rollover
Using a crossover or straight-through cable incorrectly between devices may not damage the
devices, but connectivity and communication between the devices will not take place. This is a
common error in the lab and checking that the device connections are correct should be the first
troubleshooting action if connectivity is not achieved.
provides better noise protection than UTP cabling, however at a significantly higher price. For
many years, STP was the cabling structure specified for use in Token Ring network installations.
With the use of Token Ring declining, the demand for shielded twisted-pair cabling has also
waned. The new 10 GB standard for Ethernet has a provision for the use of STP cabling. This
may provide a renewed interest in shielded twisted-pair cabling.
Cable insulation and sheaths may be flammable or produce toxic fumes when heated or burned.
Building authorities or organizations may stipulate related safety standards for cabling and
hardware installations.
Fiber Media
Fiber-optic cabling uses either glass or plastic fibers to guide light impulses from source to
destination. The bits are encoded on the fiber as light impulses. Optical fiber cabling is capable
of very large raw data bandwidth rates. Most current transmission standards have yet to approach
the potential bandwidth of this media.
More expensive (usually) than copper media over the same distance (but for a higher
capacity)
Different skills and equipment required to terminate and splice the cable infrastructure
At present, in most enterprise environments, optical fiber is primarily used as backbone cabling
for high-traffic point-to-point connections between data distribution facilities and for the
interconnection of buildings in multi-building campuses. Because optical fiber does not conduct
electricity and has low signal loss, it is well suited for these uses.
Cable Construction
Optical fiber cables consist of a PVC jacket and a series of strengthening materials that surround
the optical fiber and its cladding. The cladding surrounds the actual glass or plastic fiber and is
designed to prevent light loss from the fiber. Because light can only travel in one direction over
optical fiber, two fibers are required to support full duplex operation. Fiber-optic patch cables
bundle together two optical fiber cables and terminate them with a pair of standard single fiber
connectors. Some fiber connectors accept both the transmitting and receiving fibers in a single
connector.
Wireless Media
Wireless media carry electromagnetic signals at radio and microwave frequencies that represent
the binary digits of data communications. As a networking medium, wireless is not restricted to
conductors or pathways, as are copper and fiber media. Wireless data communication
technologies work well in open environments. However, certain construction materials used in
buildings and structures, and the local terrain, will limit the effective coverage. In addition,
wireless is susceptible to interference and can be disrupted by such common devices as
household cordless phones, some types of fluorescent lights, microwave ovens, and other
wireless communications. Further, because wireless communication coverage requires no access
to a physical strand of media, devices and users who are not authorized for access to the network
can gain access to the transmission. Therefore, network security is a major component of
wireless network administration.
Standard IEEE 802.15 - Wireless Personal Area Network (WPAN) standard, commonly
known as "Bluetooth", uses a device pairing process to communicate over distances from
1 to 100 meters.
Other wireless technologies such as satellite communications provide data network connectivity
for locations without another means of connection. Protocols including GPRS enable data to be
transferred between earth stations and satellite links. In each of the above examples, Physical
layer specifications are applied to areas that include: data to radio signal encoding, frequency and
power of transmission, signal reception and decoding requirements, and antenna design and
construction.
Wireless Access Point (AP) - Concentrates the wireless signals from users and connects,
usually through a copper cable, to the existing copper-based network infrastructure such
as Ethernet.
As the technology has developed, a number of WLAN Ethernet-based standards have emerged.
Care needs to be taken in purchasing wireless devices to ensure compatibility and
interoperability.
Standards include:
IEEE 802.11a - Operates in the 5 GHz frequency band and offers speeds of up to 54 Mbps.
Because this standard operates at higher frequencies, it has a smaller coverage area and is less
effective at penetrating building structures. Devices operating under this standard are not
interoperable with the 802.11b and 802.11g standards described below.
IEEE 802.11b - Operates in the 2.4 GHz frequency band and offers speeds of up to 11 Mbps.
Devices implementing this standard have a longer range and are better able to penetrate building
structures than devices based on 802.11a.
IEEE 802.11g - Operates in the 2.4 GHz frequency band and offers speeds of up to 54 Mbps.
Devices implementing this standard therefore operate at the same radio frequency and range as
802.11b but with the bandwidth of 802.11a.
IEEE 802.11n
The IEEE 802.11n standard is currently in draft form. The proposed standard defines frequency
of 2.4 Ghz or 5 GHz. The typical expected data rates are 100 Mbps to 210 Mbps with a distance
range of up to 70 meters. The benefits of wireless data communications technologies are evident,
especially the savings on costly premises wiring and the convenience of host mobility. However,
network administrators need to develop and apply stringent security policies and processes to
protect wireless LANs from unauthorized access and damage. These wireless standards and
Wireless LAN implementations will be covered in more detail in the LAN Switching and
Wireless course.
Common Copper Media Connectors
Different Physical layer standards specify the use of different connectors. These standards
specify the mechanical dimensions of the connectors and the acceptable electrical properties of
each type for the different implementations in which they are employed. Although some
connectors may look the same, they may be wired differently according to the Physical layer
specification for which they were designed. The ISO 8877 specified RJ-45 connector is used for
a range of Physical layer specifications, one of which is Ethernet. Another specification, EIATIA 568, describes the wire color codes to pin assignments (pinouts) for Ethernet straightthrough and crossover cables. Although many types of copper cables can be purchased pre-made,
in some situations, especially in LAN installations, the termination of copper media may be
performed onsite. These terminations include crimped connections to terminate Cat5 media with
RJ-45 plugs to make patch cables, and the use of punched down connections on 110 patch panels
and RJ-45 jacks. The figure shows some of the Ethernet wiring components.
Misalignment - the fiber-optic media are not precisely aligned to one another when
joined.
End gap - the media do not completely touch at the splice or connection.
End finish - the media ends are not well polished or dirt is present at the termination.
It is recommended that an Optical Time Domain Reflectometer (OTDR) be used to test each
fiber-optic cable segment. This device injects a test pulse of light into the cable and measures
back scatter and reflection of light detected as a function of time. The OTDR will calculate the
approximate distance at which these faults are detected along the length of the cable. A field test
can be performed by shining a bright flashlight into one end of the fiber while observing the
other end of the fiber. If light is visible, then the fiber is capable of passing light. Although this
does not ensure the performance of the fiber, it is a quick and inexpensive way to find a broken
fiber.