JIS Section
JIS Section
日本标准
SS 330 Steel plates and - - 0.05 0.05 205 195 175 330 to 430 Steel plates and sheets, coils and flats
(SS 34) sheets, coils, flats and t£5
bars Steel plates and sheets, coils and flats
5<t£16
Steel plates and sheets, coils and flats
16<t£50
Steel plates and sheets, and flats
t>40
Steel bars t£25 in diameter, side or distance across flats
SS 400 Steel plates and - - 0.05 0.05 245 235 215 400 to 510 Steel plates and sheets, coils, flats and sections
(SS 41) sheets, coils, sections, t£5
flats and bars Steel plates and sheets, coils, flats and sections
5<t£16
Steel plates and sheets, coils, flats and sections
16<t£50
Steel plates and sheets, flats and sections
t>40
Steel bars t£25 in diameter, side or distance across flats
SS 490 Steel plates and - - 0.05 0.05 285 275 255 490 to 610 Steel plates and sheets, coils, flats and sections
(SS 50) sheets, coils, sections, t£5
flats and bars Steel plates and sheets, coils, flats and sections
5<t£16
Steel plates and sheets, coils, flats and sections
16<t£50
Steel plates and sheets, flats and sections
t>40
Steel bars t£25 in diameter, side or distance across flats
SS 540 Steel plates and 0.30 1.60 0.04 0.04 400 390 - 540 Steel plates and sheets, coils, flats and sections
(SS 55) sheets, coils, sections, t£5
and flats 40mm or
under in thickness and Steel plates and sheets, coils, flats and sections
steel bars 40mm or 5<t£16
under in diameter, side
length or distance Steel plates and sheets, coils, flats and sections
across flats 16<t£40
SM490YA
t£100 0.20 0.55 1.60 0.035 0.035 365
(SM50YA) Steel plate, coil, section
SM490YB and flat
t£100 0.20 0.55 1.60 0.035 0.035 365
(SM50YB)
SM520C Steel plate, coil and t£100 0.20 0.55 1.60 0.035 0.035 365
section
https://www.leonghuat.com/specifications/jis_g3101_1995.htm 2/14/2019
JIS G3101 1995 Page 2 of 2
£40 40£t£100 6£t<12 12£t<16 = 16 16<t£40 40<t£100 6£t<12 12£t<16 = 16 16<t£40 40<t£100 6£t£16 16£<t£50 40
SN400A 6£t£100 0.24 - - 0.05 0.05 - - 235 235 235 235 215 - - - - - 17 21
6£t£50 0.6 to 2352) to 2352) to
0.20 0.35 0.03 0.015 0.36 0.36 235 235 to 355 215 to 355 - 803) 803) 80 80 18 22
CSW5) =0.26 1.4 355 355
SN400B 2)
50<t£100 0.6 to 235 to 2352) to
0.22 0.35 0.03 0.015 0.36 0.36 235 235 to 355 215 to 355 400 to 510 - 803) 803) 80 80 18 22
CSW5) =0.26 1.4 355 355
6£t£50
0.20 0.35
0.6 to
0.02 0.008 0.36 0.36 N.A. N.A. 2352) to 235 to 355 215 to 355 N.A. N.A. 3)
80 80 18 22
80
CSW5) =0.26 1.4 355
SN400C
50<t£100
0.22 0.35
0.6 to
0.02 0.008 0.36 0.36 N.A. N.A. 2352) to 235 to 355 215 to 355 N.A. N.A. 3)
80 80 18 22
80
CSW5) =0.26 1.4 355
6£t£50 3252) to 3252) to
0.18 0.55 1.6 0.03 0.015 0.44 0.46 325 325 to 445 295 to 415 - 803) 803) 80 80 17 21
CSW5) =0.29 445 445
SN490B
50<t£100 3252) to 3252) to
0.20 0.55 1.6 0.03 0.015 0.44 0.46 325 325 to 445 295 to 415 - 803) 803) 80 80 17 21
CSW5) =0.29 445 445
490 to 610
6£t£50
0.18 0.55 1.6 0.02 0.008 0.44 0.46 N.A. N.A. 3252) to 325 to 445 295 to 415 N.A. N.A. 3)
80 80 17 21
80
CSW5) =0.29 445
SN490C
50<t£100 3252) to
0.20 0.55 1.6 0.02 0.008 0.44 0.46 N.A. N.A. 325 to 445 295 to 415 N.A. N.A. 803) 80 80 17 21
CSW5) =0.29 445
Notes : 1), 2), 3), 4), 5) references shall be made to JIS Handbook, Ferrous Materials & Metallurgy II, 1998
SPCD 270 34 36 38 39 40 41
No.5 in rolling direction
SPCE3) 270 36 38 40 41 42 43
Notes :
1) The tensile test value is not applicable to SPPC. When (SPCCT) is specified, values in parentheses shall be applied.
2) For those less than 0.60mm in thickness, the tensile test is omitted.
3) When the steel sheet and coil of standard tempered grade in quality SPCE are specified non-aging property (SPCEN), this shall be guaranteed for 6 months after shipment from the manufacturer's factory.
https://www.leonghuat.com/specifications/jis_g3101_1995.htm 2/14/2019