Scribd Logo
Hochladen

Welcome to Scribd!

  • 765 views

    Compliance Statement - Section 26 Paint

    Uploaded by

    Mariam Mousa
    1. The document provides product and application details for Hempadur 85671 primer paint to be used on the Baladna Dairy Farm Phase 2 project. 2. Hempadur 85671 is a two-component, amine adduct cured phenolic epoxy primer that provides good adhesion and resistance to heat, water, and chemicals. 3. The primer requires proper surface preparation including removal of oils, grease, salts, and other contaminants before application at the specified dry film thickness.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Flag for inappropriate content

    Compliance Statement - Section 26 Paint

    Uploaded by

    Mariam Mousa
    765 views2 pages
    1. The document provides product and application details for Hempadur 85671 primer paint to be used on the Baladna Dairy Farm Phase 2 project. 2. Hempadur 85671 is a two-component, amine adduct cured phenolic epoxy primer that provides good adhesion and resistance to heat, water, and chemicals. 3. The primer requires proper surface preparation including removal of oils, grease, salts, and other contaminants before application at the specified dry film thickness.

    Original Description:

    compliance statement paint

    Original Title

    Compliance Statement - Section 26 Paint

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. The document provides product and application details for Hempadur 85671 primer paint to be used on the Baladna Dairy Farm Phase 2 project. 2. Hempadur 85671 is a two-component, amine adduct cured phenolic epoxy primer that provides good adhesion and resistance to heat, water, and chemicals. 3. The primer requires proper surface preparation including removal of oils, grease, salts, and other contaminants before application at the specified dry film thickness.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as docx, pdf, or txt
    765 views2 pages

    Compliance Statement - Section 26 Paint

    Uploaded by

    Mariam Mousa
    1. The document provides product and application details for Hempadur 85671 primer paint to be used on the Baladna Dairy Farm Phase 2 project. 2. Hempadur 85671 is a two-component, amine adduct cured phenolic epoxy primer that provides good adhesion and resistance to heat, water, and chemicals. 3. The primer requires proper surface preparation including removal of oils, grease, salts, and other contaminants before application at the specified dry film thickness.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as docx, pdf, or txt
    of 2

    MATERIAL SUBMITTAL FOR

    PRIMER PAINT HEMPADUR 85671


    BALADNA DAIRY FARM PHASE 2

    U0733BDF2-TTC-MAS-A-00XX Rev.00 25/12/2019

    COMPLIANCE STATEMENT
    QCS 2014 Section 26: Painting and Decorating Titanium 4 Material Status Remarks
    Part 03: Primers, Paints and Coatings Submittal
    3 PRIMERS, PAINTS AND COATINGS
    3.1 GENERAL REQUIREMENTS
    3.1.2 References
    1 The following Standards are referred to in this Section:
    BS 4652...................... Metallic zinc-rich priming paint Part of Group Assortment.
    (organic media) Local availability subject to
    BS 4756...................... Ready-mixed aluminium priming confirmation.
    paints for woodwork In accordance with
    BS 5082...................... Water-borne priming paints for ARAMCO's specification
    woodwork APCS 2A, 2B and 2C.
    BS 5358...................... Solvent-borne priming paints for Conforms to Norsok M-501,
    woodwork. system no. 3C, 3D, 3E and
    3F.Complies with Section
    175.300 of the Code of
    Federal Regulations Title 21
    – Liquid and Dry Foodstuff.
    Consult Hempel for details.
    Approved by WRAS for
    potable water up to
    23°C/73°F. Shades:11150 /
    50900
    3.2 APPLICATION
    3.2.1 General Noted. Please refer to below
    1.Coatings are to be applied in accordance with the manufacturer recommended
    manufacturer’s instruction to clean, dry application. SURFACE
    surfaces, in dust free and dry atmospheric conditions and PREPARATION: New steel:
    after any previous coats have Remove oil and grease etc.
    Hardened. thoroughly with suitable
    2.All brand of primers, paints and coatings are to be detergent. Remove salts and
    approved and shall comply with the other contaminants by high
    relevant British Standards. pressure fresh water
    3. Paints of of different brands are not to be mixed or used cleaning. Abrasive blasting
    in the same coating system. to near white metal Sa 2½
    4.No dilution of painting materials is to be allowed except (ISO8501-1:2007) with a
    strictly as detailed by the surface profile
    manufacturers and as approved by the Engineer corresponding to Rugotest
    5.No primed or undercoated woodwork and metalwork is to No. 3, BN10a, Keane-Tator
    be left in an exposed or unsuitable Comparator
    location for any undue period before completion of the 3.0 G/S, or ISO Comparator
    painting process. No exterior or Medium (G).
    MATERIAL SUBMITTAL FOR
    PRIMER PAINT HEMPADUR 85671
    BALADNA DAIRY FARM PHASE 2

    U0733BDF2-TTC-MAS-A-00XX Rev.00 25/12/2019

    exposed painting is to be carried out under adverse weather


    conditions, such as rain,
    extreme humidity, dust storms, etc.
    3.3 PRIMERS AND UNDERCOATINGS
    3.3.1 Materials HEMPADUR 85671 is a two-
    1. Primers for plaster and rendering are to be alkali resistant. component, amine adduct
    Primers for other surfaces shall cured phenolic epoxy
    comply with Table 3.1. QCS (novolac) coating with
    very good adhesion and high
    temperature, water and
    chemical resistance.
    3.3.2 Workmanship Main contractor will ensure
    1 Priming coats are to be applied by brush unless other that surface preparation
    methods are approved taking care to should be stable, firm, dry,
    work the primer into the surface, joints, angles and end and free of dust, sand, loose
    grain. old paint, laitance, dirt,
    2 Any primed surfaces which have deteriorated on site or in grease and oil. It is
    transit are to be touched up to the recommended to apply a
    approval of the Engineer. primer/sealer prior to the
    3 All surfaces of joinery which have not been primed in the application of the specified
    workshop are to be primed filler. Touch-up with
    immediately on arrival at site and before fixing. primer/sealer on areas
    4 Undercoats are to be applied as an even film over all repaired with filler is recom-
    exposed surfaces avoiding an uneven mended prior to application
    thickness at edges and angles. of topcoat
    5 All priming and undercoats are to be rubbed down to a
    smooth surface with fine abrasive
    paper and cleaned of all dust before the application of the
    next coat

    END OF PART

    You might also like