1. The document provides design specifications for the scantling of a breasting pontoon. Key dimensions of the pontoon include a length of 8m, breadth of 4m, and maximum loaded draft of 0.5m.
2. Calculations are presented for determining the minimum required plate thicknesses of various pontoon components, including the deck, bottom, and side plating, based on structural standards.
3. Section modulus calculations are also shown for transverse and longitudinal girders and stiffeners to check their adequacy based on span, spacing, applied pressure and strength standards. Corrosion allowance of 3mm is considered for all components.
1. The document provides design specifications for the scantling of a breasting pontoon. Key dimensions of the pontoon include a length of 8m, breadth of 4m, and maximum loaded draft of 0.5m.
2. Calculations are presented for determining the minimum required plate thicknesses of various pontoon components, including the deck, bottom, and side plating, based on structural standards.
3. Section modulus calculations are also shown for transverse and longitudinal girders and stiffeners to check their adequacy based on span, spacing, applied pressure and strength standards. Corrosion allowance of 3mm is considered for all components.
1. The document provides design specifications for the scantling of a breasting pontoon. Key dimensions of the pontoon include a length of 8m, breadth of 4m, and maximum loaded draft of 0.5m.
2. Calculations are presented for determining the minimum required plate thicknesses of various pontoon components, including the deck, bottom, and side plating, based on structural standards.
3. Section modulus calculations are also shown for transverse and longitudinal girders and stiffeners to check their adequacy based on span, spacing, applied pressure and strength standards. Corrosion allowance of 3mm is considered for all components.
REVISION DATE BY CHECKED APPROVED REVISION DATE BY 1
CHECKED APPROVED4 . 06/08/2021 BAL BAL
1. PONTOON DESIGN
1.1 Pontoon Data
Pontoon Length = 8 m Pontoon Breadth = 4 m Ponroon Depth = 1.5 m Maximum Loaded Draft, hs = 0.5 m Maximum Stiffner Spacing = 0.7 m f 1 Stiffner Span 1 m Corrossion Allowance 3 mm
Environment Data 1.5 m
Water Depth = 6 m Water Density = 1025 kg/m3
1.2. Pontoon Scantling
1.2.1 Plating The minimum deck plate thickness is calculated as per DNVGL-RU-FD-Sec. 7.3.1.2 Minimum Plate Thickness td = t = s√LD/f1 (mm) 2.0 mm
1.2.2 Bottom Plating
The minimum bottom plate thickness is calculated as per DNVGL-RU-FD-Sec. 7.3.1.2 Bottom Plate Thickness = t=15.8kas√P/σ+tk 5.0 mm Spacing = 0.7 m ka = (1.1 - 0.25*s/l)2 1.0 (min, 07.2. max, 1.0) P = ρgh 5.0 kPa σ = 160ƒ1 160 MPa
1.2.3 Deck Plating
The minimum Deck plate thickness is calculated as per DNVGL-RU-FD-Sec. 7.3.1.2 Bottom Plate Thickness = t=15.8kas√P/σ+tk 5.0 mm Spacing = 0.7 m ka = (1.1 - 0.25*s/l)2 1.0 (min, 07.2. max, 1.0) P = ρgh 5.0 kPa σ = 160ƒ1 160 MPa PROJECT NO. ACTIVITY Marine Facilities PROJECT Breasting Pontoon Design FILE SUBJECT Pontoon Scantling SHEET OF ####
REVISION DATE BY CHECKED APPROVED REVISION DATE BY 2
CHECKED APPROVED4 . 06/08/2021 BAL BAL
1.2.4 Transverse Side Plating (Aft & Bow)
The minimum Deck plate thickness is calculated as per DNVGL-RU-FD-Sec. 7.3.1.2 Bottom Plate Thickness = t=15.8kas√P/σ+tk 5.0 mm Spacing = 0.7 m ka = (1.1 - 0.25*s/l)2 1.0 (min, 07.2. max, 1.0) P = ρgh 5.0 kPa σ = 160ƒ1 160 MPa 1.2.4 Midship Plating The minimum Deck plate thickness is calculated as per DNVGL-RU-FD-Sec. 7.3.1.2 Bottom Plate Thickness = t=15.8kas√P/σ+tk 5.0 mm Spacing = 0.7 m ka = (1.1 - 0.25*s/l)2 1.0 (min, 07.2. max, 1.0) P = ρgh 5.0 kPa σ = 160ƒ1 160 MPa
1.2.5 Longitudinal Side Plating (Port&Starboard)
The minimum Deck plate thickness is calculated as per DNVGL-RU-FD-Sec. 7.3.1.2 Bottom Plate Thickness = t=15.8kas√P/σ+tk = 4.1 mm Spacing = 0.4 m ka = (1.1 - 0.25*s/l)2 = 1.0 (min, 07.2. max, 1.0) P = ρgh = 5.0 kPa σ = 160ƒ1 = 160 MPa
1.2.6 Longitudinal Bulkhead Plating
The minimum Deck plate thickness is calculated as per DNVGL-RU-FD-Sec. 7.3.1.2 Bottom Plate Thickness = t=15.8kas√P/σ+tk = 4.4 mm Spacing = 0.5 m ka = (1.1 - 0.25*s/l)2 = 1.0 (min, 07.2. max, 1.0) P = ρgh = 5.0 kPa σ = 160ƒ1 = 160 MPa PROJECT NO. ACTIVITY Marine Facilities PROJECT Breasting Pontoon Design FILE SUBJECT Pontoon Scantling SHEET OF ####
REVISION DATE BY CHECKED APPROVED REVISION DATE BY 3
CHECKED APPROVED4 . 06/08/2021 BAL BAL
1.2.7 Girders and Stiffeners Check
Bottom & Deck Tranverse Girder The minimum section modulus of the bottom girder is calculated as per DNVGL-RU-FD-Sec. 7.3.2.1 The minimum section modulus, Z = (1000/σm)l2spwk = 16.2 cm3 Girder Span l = 2 m Girder Spacing s 1.375 m m = 10
p=ρgh 5.028 kPa
σ = 160ƒ1 = 222.4 MPa f1 = 1.39 w = 1 + 0.05(tkw + tkf) = 1.3 tkw, tkf = 3 mm
1.2.8 Bottom & Deck Longitudinal Stiffeners
The minimum section modulus of the bottom girder is calculated as per DNVGL-RU-FD-Sec. 7.3.2.1 The minimum section modulus, Z = (1000/σm)l2spwk = 3.9 cm3 Stiffener Span l = 1.375 m Stiffener Spacing s 0.7 m m = 10 p=ρgh 5.028 kPa σ = 160ƒ1 = 222.4 MPa f1 = 1.39 w = 1 + 0.05(tkw + tkf) = 1.3 tkw, tkf = 3 mm
1.2.9 Transverse & Midship Stiffeners
The minimum section modulus of the bottom girder is calculated as per DNVGL-RU-FD-Sec. 7.3.2.1 The minimum section modulus, Z = (1000/σm)l2spwk = 4.6 cm3 Stiffener Span l = 1.5 m Stiffener Spacing s 0.7 m m = 10 p=ρgh 5.028 kPa σ = 160ƒ1 = 222.4 MPa f1 = 1.39 w = 1 + 0.05(tkw + tkf) = 1.3 tkw, tkf = 3 mm PROJECT NO. ACTIVITY Marine Facilities PROJECT Breasting Pontoon Design FILE SUBJECT Pontoon Scantling SHEET OF ####
REVISION DATE BY CHECKED APPROVED REVISION DATE BY 4
CHECKED APPROVED4 . 06/08/2021 BAL BAL
1.2.10 Longitudinal Side Stiffeners
The minimum section modulus of the bottom girder is calculated as per DNVGL-RU-FD-Sec. 7.3.2.1 The minimum section modulus, Z = (1000/σm)l2spwk = 2.1 cm3 Stiffener Span l = 1.375 m Stiffener Spacing s 0.375 m m = 10 p=ρgh 5.028 kPa σ = 160ƒ1 = 222.4 MPa f1 = 1.39 w = 1 + 0.05(tkw + tkf) = 1.3 tkw, tkf = 3 mm
1.2.11 Longitudinal Bulkhead Side Stiffeners
The minimum section modulus of the bottom girder is calculated as per DNVGL-RU-FD-Sec. 7.3.2.1 The minimum section modulus, Z = (1000/σm)l2spwk = 2.8 cm3 Stiffener Span l = 1.375 m Stiffener Spacing s 0.5 m m = 10 p=ρgh 5.028 kPa σ = 160ƒ1 = 222.4 MPa f1 = 1.39 w = 1 + 0.05(tkw + tkf) = 1.3 tkw, tkf = 3 mm