ACI 318M-08 Building Code Requirements For Structural Concrete (ACI 318M-08) and Commentary
ACI 318M-08 Building Code Requirements For Structural Concrete (ACI 318M-08) and Commentary
Copyright by the American Concrete Institute, Farmington Hills, MI. All rights reserved. This material
may not be reproduced or copied, in whole or part, in any printed, mechanical, electronic, film, or other
distribution and storage media, without the written consent of ACI.
The technical committees responsible for ACI committee reports and standards strive to avoid ambiguities,
omissions, and errors in these documents. In spite of these efforts, the users of ACI documents occa-
sionally find information or requirements that may be subject to more than one interpretation or may be
incomplete or incorrect. Users who have suggestions for the improvement of ACI documents are
requested to contact ACI.
ACI committee documents are intended for the use of individuals who are competent to evaluate the
significance and limitations of its content and recommendations and who will accept responsibility for the
application of the material it contains. Individuals who use this publication in any way assume all risk and
accept total responsibility for the application and use of this information.
All information in this publication is provided “as is” without warranty of any kind, either express or implied,
including but not limited to, the implied warranties of merchantability, fitness for a particular purpose or
non-infringement.
ACI and its members disclaim liability for damages of any kind, including any special, indirect, incidental,
or consequential damages, including without limitation, lost revenues or lost profits, which may result
from the use of this publication.
It is the responsibility of the user of this document to establish health and safety practices appropriate to
the specific circumstances involved with its use. ACI does not make any representations with regard to
health and safety issues and the use of this document. The user must determine the applicability of all
regulatory limitations before applying the document and must comply with all applicable laws and regula-
tions, including but not limited to, United States Occupational Safety and Health Administration (OSHA)
health and safety standards.
Order information: ACI documents are available in print, by download, on CD-ROM, through electronic
subscription, or reprint and may be obtained by contacting ACI.
Most ACI standards and committee reports are gathered together in the annually revised ACI Manual of
Concrete Practice (MCP).
ISBN 978-0-87031-283-0
BUILDING CODE REQUIREMENTS FOR
STRUCTURAL CONCRETE (ACI 318M-08)
AND COMMENTARY
REPORTED BY ACI COMMITTEE 318
ACI Committee 318
Structural Building Code
Subcommittee Members
Neal S. Anderson David Darwin Andres Lepage Suzanne D. Nakaki David H. Sanders
Mark A. Aschheim Robert J. Frosch LeRoy A. Lutz Theodore L. Neff Guillermo Santana
F. Michael Bartlett Harry A. Gleich James G. MacGregor Andrzej S. Nowak Andrew Scanlon
John F. Bonacci R. Doug Hooton Joe Maffei Gustavo J. Parra-Montesinos John F. Stanton
JoAnn P. Browning L. S. Paul Johal Karl F. Meyer Jose A. Pincheira Fernando Reboucas Stucchi
Nicholas J. Carino Michael E. Kreger Denis Mitchell Randall W. Poston Raj Valluvan
Ronald A. Cook Jason J. Krohn Vilas S. Mujumdar Bruce W. Russell John W. Wallace
Juan P. Covarrubias Daniel A. Kuchma
Liaison Members
Consulting Members
PREFACE
The “Building Code Requirements for Structural Concrete” (“Code”) covers the materials, design, and construction
of structural concrete used in buildings and where applicable in nonbuilding structures. The Code also covers the
strength evaluation of existing concrete structures.
Among the subjects covered are: drawings and specifications; inspection; materials; durability requirements;
concrete quality, mixing, and placing; formwork; embedded pipes; construction joints; reinforcement details; analysis
and design; strength and serviceability; flexural and axial loads; shear and torsion; development and splices of
reinforcement; slab systems; walls; footings; precast concrete; composite flexural members; prestressed concrete; shells
and folded plate members; strength evaluation of existing structures; provisions for seismic design; structural plain
concrete; strut-and-tie modeling in Appendix A; alternative design provisions in Appendix B; alternative load and
strength reduction factors in Appendix C; and anchoring to concrete in Appendix D.
The quality and testing of materials used in construction are covered by reference to the appropriate ASTM standard
specifications. Welding of reinforcement is covered by reference to the appropriate AWS standard.
Uses of the Code include adoption by reference in general building codes, and earlier editions have been widely used
in this manner. The Code is written in a format that allows such reference without change to its language. Therefore,
background details or suggestions for carrying out the requirements or intent of the Code portion cannot be included.
The Commentary is provided for this purpose. Some of the considerations of the committee in developing the Code
portion are discussed within the Commentary, with emphasis given to the explanation of new or revised provisions.
Much of the research data referenced in preparing the Code is cited for the user desiring to study individual questions
in greater detail. Other documents that provide suggestions for carrying out the requirements of the Code are also cited.
Keywords: admixtures; aggregates; anchorage (structural); beam-column frame; beams (supports); building codes; cements; cold weather construction;
columns (supports); combined stress; composite construction (concrete and steel); composite construction (concrete to concrete); compressive strength;
concrete construction; concrete slabs; concretes; construction joints; continuity (structural); contraction joints; cover; curing; deep beams; deflections; drawings;
earthquake-resistant structures; embedded service ducts; flexural strength; floors; folded plates; footings; formwork (construction); frames; hot weather
construction; inspection; isolation joints; joints (junctions); joists; lightweight concretes; load tests (structural); loads (forces); materials; mixing; mixture proportioning;
modulus of elasticity; moments; pipe columns; pipes (tubing); placing; plain concrete; precast concrete; prestressed concrete; prestressing steels; quality control;
reinforced concrete; reinforcing steels; roofs; serviceability; shear strength; shear walls; shells (structural forms); spans; specifications; splicing; strength; strength
analysis; stresses; structural analysis; structural concrete; structural design; structural integrity; T-beams; torsion; walls; water; welded wire reinforcement.
ACI 318M-08 was adopted as a standard of the American Concrete disclaims any and all responsibility for the stated principles. The Institute
Institute November 2007 to supersede ACI 318M-05 in accordance with the shall not be liable for any loss or damage arising therefrom. Reference to
Institute’s standardization procedure and was published July 2008. this Commentary shall not be made in contract documents. If items found
A complete U.S. Customary unit companion to ACI 318M has been in this Commentary are desired by the licensed design professional to be
developed, 318; therefore, no U.S. Customary unit equivalents are included a part of the contract documents, they shall be restated and incorporated
in mandatory language.
in this document.
Copyright © 2008, American Concrete Institute.
ACI Committee Reports, Manuals, Guides, Standard Practices, and
All rights reserved including rights of reproduction and use in any form
Commentaries are intended for guidance in planning, designing, executing,
or by any means, including the making of copies by any photo process, or
and inspecting construction. This Commentary is intended for the use of by any electronic or mechanical device, printed or written or oral, or
individuals who are competent to evaluate the significance and limitations recording for sound or visual reproduction or for use in any knowledge or
of its content and recommendations and who will accept responsibility for retrieval system or device, unless permission in writing is obtained from the
the application of the material it contains. The American Concrete Institute copyright proprietors.
CONTENTS
INTRODUCTION ...................................................................................................................................... 7
CHAPTER 3—MATERIALS................................................................................................................... 41
3.1—Tests of materials.......................................................................................................................................................... 41
3.2—Cementitious materials.................................................................................................................................................. 41
3.3—Aggregates.................................................................................................................................................................... 42
3.4—Water............................................................................................................................................................................. 42
3.5—Steel reinforcement ....................................................................................................................................................... 43
3.6—Admixtures .................................................................................................................................................................... 49
3.7—Storage of materials ...................................................................................................................................................... 49
3.8—Referenced standards................................................................................................................................................... 49
21.6—Special moment frame members subjected to bending and axial load ..................................................................... 339
21.7—Joints of special moment frames............................................................................................................................... 343
21.8—Special moment frames constructed using precast concrete.................................................................................... 347
21.9—Special structural walls and coupling beams ............................................................................................................ 349
21.10—Special structural walls constructed using precast concrete ................................................................................... 356
21.11—Structural diaphragms and trusses ......................................................................................................................... 357
21.12—Foundations ............................................................................................................................................................ 362
21.13—Members not designated as part of the seismic-force-resisting system ................................................................. 365
INDEX................................................................................................................................................... 467
The ACI Building Code Requirements for Structural Concrete (“Code”) and Commentary are presented in a side-by-side
column format, with Code text placed in the left column and the corresponding Commentary text aligned in the right column.
To further distinguish the Code from the Commentary, the Code has been printed in Helvetica, the same type face in which
this paragraph is set.
This paragraph is set in Times Roman, and all portions of the text exclusive to the Commentary are printed in this type face. Commentary
section numbers are preceded by an “R” to further distinguish them from Code section numbers.
Except for Chapters 4 and 21, substantive changes from 318M-05 are indicated with vertical lines in the margin (editorial
changes not indicated). Changes to the provisions of Chapters 4 and 21 are not indicated by a vertical line because the
provisions were renumbered for this edition.
The Commentary is not intended to provide a complete The Code provides a means of establishing minimum standards
historical background concerning the development of the for acceptance of designs and construction by legally
Code,* nor is it intended to provide a detailed résumé of the appointed building officials or their designated representatives.
studies and research data reviewed by the committee in The Code and Commentary are not intended for use in settling
formulating the provisions of the Code. However, references disputes between the owner, engineer, architect, contractor, or
to some of the research data are provided for those who wish their agents, subcontractors, material suppliers, or testing
to study the background material in depth. agencies. Therefore, the Code cannot define the contract
responsibility of each of the parties in usual construction.
As the name implies, “Building Code Requirements for General references requiring compliance with the Code in the
Structural Concrete” is meant to be used as part of a legally project specifications should be avoided since the contractor is
adopted building code and as such must differ in form and rarely in a position to accept responsibility for design details or
substance from documents that provide detailed specifications, construction requirements that depend on a detailed knowledge
recommended practice, complete design procedures, or of the design. Design-build construction contractors, however,
design aids. typically combine the design and construction responsibility.
Generally, the drawings, specifications, and contract documents
The Code is intended to cover all buildings of the usual
should contain all of the necessary requirements to ensure
types, both large and small. Requirements more stringent
compliance with the Code. In part, this can be accomplished
than the Code provisions may be desirable for unusual
by reference to specific Code sections in the project specifi-
construction. The Code and Commentary cannot replace
cations. Other ACI publications, such as “Specifications for
sound engineering knowledge, experience, and judgment.
Structural Concrete (ACI 301M)” are written specifically for
A building code states only the minimum requirements use as contract documents for construction.
necessary to provide for public health and safety. The Code
is based on this principle. For any structure, the owner or the It is recommended to have testing and certification programs
licensed design professional may require the quality of for the individual parties involved with the execution of
materials and construction to be higher than the minimum work performed in accordance with this Code. Available for
this purpose are the plant certification programs of the
Precast/Prestressed Concrete Institute, the Post-Tensioning
Institute, and the National Ready Mixed Concrete Associa-
*
For a history of the ACI Building Code see Kerekes, F., and Reid, H. B., Jr., “Fifty tion; the personnel certification programs of the American
Years of Development in Building Code Requirements for Reinforced Concrete,” ACI
JOURNAL, Proceedings V. 50, No. 6, Feb. 1954, p. 441. For a discussion of code philos- Concrete Institute and the Post-Tensioning Institute; and the
ophy, see Siess, C. P., “Research, Building Codes, and Engineering Practice,” ACI
JOURNAL, Proceedings V. 56, No. 5, May 1960, p. 1105. Concrete Reinforcing Steel Institute’s Voluntary Certification
Program for Fusion-Bonded Epoxy Coating Applicator The chapters on foundations provide design tables for square
Plants. In addition, “Standard Specification for Agencies footings, pile caps, drilled piers (caissons), and cantilevered
Engaged in Construction Inspecting and/or Testing” (ASTM retaining walls. Other design aids are presented for crack
E329-06a) specifies performance requirements for inspection control; and development of reinforcement and lap splices.)
and testing agencies.
“Reinforcement Anchorages and Splices,” Concrete
Design reference materials illustrating applications of the Reinforcing Steel Institute, Schaumburg, IL, 4th Edition,
Code requirements may be found in the following documents. 1997, 100 pp. (This provides accepted practices in splicing
The design aids listed may be obtained from the sponsoring reinforcement. The use of lap splices, mechanical splices,
organization. and welded splices are described. Design data are presented
for development and lap splicing of reinforcement.)
Design aids:
“Structural Welded Wire Reinforcement Manual of Stan-
“ACI Design Handbook,” Publication SP-17(97), Amer- dard Practice,” Wire Reinforcement Institute, Hartford, CT,
ican Concrete Institute, Farmington Hills, MI, 1997, 482 pp. 6th Edition, Apr. 2001, 38 pp. (This describes welded wire
(This provides tables and charts for design of eccentrically reinforcement material, gives nomenclature and wire size
loaded columns by the Strength Design Method of the 1995 and weight tables. Lists specifications and properties and
Code. Provides design aids for use in the engineering design manufacturing limitations. Book has latest code require-
and analysis of reinforced concrete slab systems carrying ments as code affects welded wire. Also gives development
loads by two-way action. Design aids are also provided for length and splice length tables. Manual contains customary
the selection of slab thickness and for reinforcement required units and soft metric units.)
to control deformation and assure adequate shear and
“Structural Welded Wire Reinforcement Detailing
flexural strengths.)
Manual,” Wire Reinforcement Institute, Hartford, CT,
1994, 252 pp. (The manual, in addition to including ACI 318
“ACI Detailing Manual—2004,” ACI Committee 315,
provisions and design aids, also includes: detailing guidance
Publication SP-66(04), American Concrete Institute, Farm-
on welded wire reinforcement in one-way and two-way
ington Hills, MI, 2004, 212 pp. (Includes the standard, ACI
slabs; precast/prestressed concrete components; columns
315-99, and report, ACI 315R-04. Provides recommended
and beams; cast-in-place walls; and slabs-on-ground. In
methods and standards for preparing engineering drawings,
addition, there are tables to compare areas and spacings of
typical details, and drawings placing reinforcing steel in
high-strength welded wire with conventional reinforcing.)
reinforced concrete structures. Separate sections define
responsibilities of both engineer and reinforcing bar detailer.) “Strength Design of Reinforced Concrete Columns,”
Portland Cement Association, Skokie, IL, 1978, 48 pp. (This
“Guide to Durable Concrete (ACI 201.2R-01),” ACI
provides design tables of column strength in terms of load in
Committee 201, American Concrete Institute, Farmington
kips versus moment in ft-kips for concrete strength of 5000 psi
Hills, MI, 2001, 41 pp. (This describes specific types of
and Grade 60 reinforcement. Design examples are included.
concrete deterioration. It contains a discussion of the mech-
Note that the PCA design tables do not include the strength
anisms involved in deterioration and the recommended reduction factor φ in the tabulated values; Mu /φ and Pu /φ
requirements for individual components of the concrete,
must be used when designing with this aid.)
quality considerations for concrete mixtures, construction
procedures, and influences of the exposure environment. “PCI Design Handbook—Precast and Prestressed
Concrete,” Precast/Prestressed Concrete Institute, Chicago, IL,
“Guide for the Design of Durable Parking Structures 6th Edition, 2004, 736 pp. (This provides load tables for
(362.1R-97 (Reapproved 2002)),” ACI Committee 362, common industry products, and procedures for design and
American Concrete Institute, Farmington Hills, MI, 1997, 33 pp. analysis of precast and prestressed elements and structures
(This summarizes practical information regarding design of composed of these elements. Provides design aids and examples.)
parking structures for durability. It also includes information
about design issues related to parking structure construction “Design and Typical Details of Connections for Precast and
and maintenance.) Prestressed Concrete,” Precast/Prestressed Concrete Institute,
Chicago, IL, 2nd Edition, 1988, 270 pp. (This updates available
“CRSI Handbook,” Concrete Reinforcing Steel Institute, information on design of connections for both structural and
Schaumburg, IL, 9th Edition, 2002, 648 pp. (This provides architectural products, and presents a full spectrum of typical
tabulated designs for structural elements and slab systems. details. This provides design aids and examples.)
Design examples are provided to show the basis of and use
of the load tables. Tabulated designs are given for beams; “Post-Tensioning Manual,” Post-Tensioning Institute,
square, round, and rectangular columns; one-way slabs; and Phoenix, AZ, 6th Edition, 2006, 354 pp. (This provides
one-way joist construction. The design tables for two-way comprehensive coverage of post-tensioning systems, speci-
slab systems include flat plates, flat slabs, and waffle slabs. fications, design aids, and construction concepts.)
CODE COMMENTARY
1.1 — Scope R1.1 — Scope
1.1.1 — This Code provides minimum requirements The American Concrete Institute “Building Code Require-
for design and construction of structural concrete ments for Structural Concrete (ACI 318M-08),” referred to
members of any structure erected under requirements as the Code or 2008 Code, provides minimum requirements
of the legally adopted general building code of which for structural concrete design or construction.
this Code forms a part. In areas without a legally
adopted building code, this Code defines minimum The 2008 Code revised the previous standard “Building
acceptable standards for materials, design, and Code Requirements for Structural Concrete (ACI
construction practice. This Code also covers the 318M-05).” This standard includes in one document the
strength evaluation of existing concrete structures. rules for all concrete used for structural purposes including
both plain and reinforced concrete. The term “structural
For structural concrete, fc′ shall not be less than 17 MPa. concrete” is used to refer to all plain or reinforced concrete
No maximum value of fc′ shall apply unless restricted used for structural purposes. This covers the spectrum of
by a specific Code provision. structural applications of concrete from nonreinforced
concrete to concrete containing nonprestressed reinforce-
ment, prestressing steel, or composite steel shapes, pipe, or
tubing. Requirements for structural plain concrete are in
Chapter 22.
1
CODE COMMENTARY
Appendix C of the Code allows the use of the factored load
combinations given in Chapter 9 of the 1999 Code.
1.1.2 — This Code supplements the general building R1.1.2 — The American Concrete Institute recommends
code and shall govern in all matters pertaining to that the Code be adopted in its entirety; however, it is recog-
design and construction of structural concrete, except nized that when the Code is made a part of a legally adopted
wherever this Code is in conflict with requirements in general building code, the general building code may
the legally adopted general building code. modify provisions of this Code.
1.1.4 — For cast-in-place footings, foundation walls, R1.1.4 — “Requirements for Residential Concrete
and slabs-on-ground for one- and two-family dwellings Construction (ACI 332) and Commentary” reported by
and multiple single-family dwellings (townhouses) and ACI Committee 332.1.1 (This addresses only the design and
their accessory structures, design and construction in construction of cast-in-place footings, foundation walls
accordance with ACI 332 shall be permitted. supported on continuous footings, and slabs-on-ground for
one- and two-family dwellings and multiple single-family
dwellings [townhouses], and their accessory structures.)
1.1.5 — For unusual structures, such as arches, bins
and silos, blast-resistant structures, and chimneys, R1.1.5 — Some structures involve unique design and
provisions of this Code shall govern where applicable. construction problems that are not covered by the Code.
See also 22.1.3. However, many Code provisions, such as the concrete
quality and design principles, are applicable for these struc-
tures. Detailed recommendations for design and construc-
tion of some special structures are given in the following
ACI publications:
CODE COMMENTARY 1
“Code for Concrete Containments” reported by Joint
ACI-ASME Committee 359.1.5 (This provides requirements
for the design, construction, and use of concrete reactor
vessels and concrete containment structures for nuclear
power plants.)
1.1.6 — This Code does not govern design and instal- R1.1.6 — The design and installation of piling fully
lation of portions of concrete piles, drilled piers, and embedded in the ground is regulated by the general building
caissons embedded in ground except for structures code. For portions of piling in air or water, or in soil not
assigned to Seismic Design Categories D, E, and F. capable of providing adequate lateral restraint throughout
See 21.12.4 for requirements for concrete piles, drilled the piling length to prevent buckling, the design provisions
piers, and caissons in structures assigned to Seismic of this code govern where applicable.
Design Categories D, E, and F.
Recommendations for concrete piles are given in detail in
“Recommendations for Design, Manufacture, and
Installation of Concrete Piles” reported by ACI
Committee 543.1.6 (This provides recommendations for the
design and use of most types of concrete piles for many
kinds of construction.)
1.1.7 — This Code does not govern design and R1.1.7 — Detailed recommendations for design and
construction of slabs-on-ground, unless the slab construction of slabs-on-ground and floors that do not
transmits vertical loads or lateral forces from other transmit vertical loads or lateral forces from other portions
portions of the structure to the soil. of the structure to the soil, and residential post-tensioned
slabs-on-ground, are given in the following publications:
1
CODE COMMENTARY
1.1.8 — Concrete on steel deck R1.1.8 — Concrete on steel deck
1.1.8.1 — Design and construction of structural R1.1.8.1 — In its most basic application, the noncomposite
concrete slabs cast on stay-in-place, noncomposite steel deck serves as a form, and the concrete slab is designed
steel deck are governed by this Code. to carry all superimposed loads.
1.1.8.2 — This Code does not govern the composite R1.1.8.2 — Another type of steel deck commonly used
design of structural concrete slabs cast on stay-in- develops composite action between the concrete and steel
place, composite steel deck. Concrete used in the deck. In this type of construction, the steel deck serves as
construction of such slabs shall be governed by the positive moment reinforcement. The design of
Chapters 1 through 6 of this Code, where applicable. composite slabs on steel deck is described in “Standard for
Portions of such slabs designed as reinforced concrete the Structural Design of Composite Slabs” (ANSI/
are governed by this Code. ASCE 3).1.11 The standard refers to the appropriate portions of
ACI 318 for the design and construction of the concrete
portion of the composite assembly. Guidelines for the
construction of composite steel deck slabs are given in
“Standard Practice for the Construction and Inspection
of Composite Slabs” (ANSI/ASCE 9).1.12 Reference 1.13
also provides guidance for design of composite slabs on steel
deck. The design of negative moment reinforcement to make
a slab continuous is a common example where a portion of
the slab is designed in conformance with this Code.
1.1.9 —Provisions for earthquake resistance R1.1.9 — Provisions for earthquake resistance
1.1.9.1 — The seismic design category of a structure R1.1.9.1 — Design requirements for an earthquake-resis-
shall be determined in accordance with the legally tant structure in this Code are determined by the Seismic
adopted general building code of which this Code forms Design Category (SDC) to which the structure is assigned.
a part, or determined by other authority having jurisdic- In general, the SDC relates to seismic hazard level, soil
tion in areas without a legally adopted building code. type, occupancy, and use of the building. Assignment of a
building to a SDC is under the jurisdiction of a general
building code rather than ACI 318.
CODE COMMENTARY 1
TABLE R1.1.9.1 — CORRELATION BETWEEN
SEISMIC-RELATED TERMINOLOGY IN MODEL
CODES
Level of seismic risk or assigned
Code, standard, or resource seismic performance or design
document and edition categories as defined in the Code
ACI 318-08; IBC 2000, 2003, 2006; SDC*
NFPA 5000, 2003, 2006; ASCE 7-98, SDC C SDC
A, B D, E, F
7-02, 7-05; NEHRP 1997, 2000, 2003
Low Moderate/ High
ACI 318-05 and previous editions seismic intermediate seismic
risk seismic risk risk
BOCA National Building Code 1993,
1996, 1999; Standard Building Code †
A, B SPC C SPC D, E
1994, 1997, 1999; ASCE 7-93; 7-95; SPC
NEHRP 1991, 1994
Uniform Building Code Seismic Seismic Seismic
1991, 1994, 1997 Zone 0, 1 Zone 2 Zone 3, 4
*
SDC= Seismic design category as defined in code, standard, or resource document.
†
SPC = Seismic performance category as defined in code, standard, or resource document.
1.1.9.2 — All structures shall satisfy the applicable R1.1.9.2 — Structures assigned to Seismic design category
provisions of Chapter 21 except those assigned to (SDC) A have the lowest seismic hazard and performance
Seismic Design Category A and those otherwise requirements. Provisions of Chapters 1 through 19 and
exempted by the legally adopted general building Chapter 22 are considered sufficient for these structures. For
code. See 21.1.1. structures assigned to other SDCs, the design requirements
of Chapter 21 apply, as delineated in 21.1.
1.1.10 — This Code does not govern design and R1.1.10 — Code Requirements for Environmental Engi-
construction of tanks and reservoirs. neering Concrete Structures” reported by ACI Committee
350.1.21 (This gives material, design and construction
recommendations for concrete tanks, reservoirs, and other
structures commonly used in water and waste treatment
works where dense, impermeable concrete with high resis-
tance to chemical attack is required. Special emphasis is
placed on a structural design that minimizes the possibility
of cracking and accommodates vibrating equipment and
other special loads. Proportioning of concrete, placement,
curing, and protection against chemicals are also described.
Design and spacing of joints receive special attention.)
1.2.1 — Copies of design drawings, typical details, and R1.2.1 — The provisions for preparation of design drawings
specifications for all structural concrete construction and specifications are, in general, consistent with those of
shall bear the seal of a licensed design professional. most general building codes and are intended as supplements.
These drawings, details, and specifications shall show:
The Code lists some of the more important items of infor-
(a) Name and date of issue of code and supplement mation that should be included in the design drawings,
to which design conforms; details, or specifications. The Code does not imply an all-
inclusive list, and additional items may be required by the
(b) Live load and other loads used in design; building official.
1
CODE COMMENTARY
(c) Specified compressive strength of concrete at
stated ages or stages of construction for which each
part of structure is designed;
1.2.2 — Calculations pertinent to design shall be filed R1.2.2 — Documented computer output is acceptable
with the drawings when required by the building official. instead of manual calculations. The extent of input and
Analyses and designs using computer programs shall output information required will vary according to the
be permitted provided design assumptions, user input, specific requirements of individual building officials.
and computer-generated output are submitted. Model However, when a computer program has been used, only
analysis shall be permitted to supplement calculations. skeleton data should normally be required. This should
consist of sufficient input and output data and other infor-
mation to allow the building official to perform a detailed
review and make comparisons using another program or
manual calculations. Input data should be identified as to
member designation, applied loads, and span lengths. The
related output data should include member designation and
the shears, moments, and reactions at key points in the span.
For column design, it is desirable to include moment magni-
fication factors in the output where applicable.
CODE COMMENTARY 1
performed well. Inspection is necessary to confirm that the
construction is in accordance with the design drawings and
project specifications. Proper performance of the structure
depends on construction that accurately represents the
design and meets code requirements within the tolerances
allowed. Qualification of the inspectors can be obtained
from a certification program, such as the ACI Certification
Program for Concrete Construction Special Inspector.
1.3.1 — Concrete construction shall be inspected as R1.3.1 — Inspection of construction by or under the
required by the legally adopted general building code. In supervision of the licensed design professional responsible
the absence of such inspection requirements, concrete for the design should be considered because the person in
construction shall be inspected throughout the various charge of the design is usually the best qualified to determine if
Work stages by or under the supervision of a licensed construction is in conformance with construction documents.
design professional or by a qualified inspector. When such an arrangement is not feasible, inspection of
construction through other licensed design professionals or
through separate inspection organizations with demonstrated
capability for performing the inspection may be used.
1.3.2 — The inspector shall require compliance with R1.3.2 — By inspection, the Code does not mean that the
design drawings and specifications. Unless specified inspector should supervise the construction. Rather, it means
otherwise in the legally adopted general building code, that the one employed for inspection should visit the project
inspection records shall include: with the frequency necessary to observe the various stages
1
CODE COMMENTARY
(a) Delivery, placement, and testing reports docu- of Work and ascertain that it is being done in compliance
menting the quantity, location of placement, fresh with contract documents and Code requirements. The
concrete tests, strength, and other test of all classes frequency should be at least enough to provide general
of concrete mixtures; knowledge of each operation, whether this is several times a
day or once in several days.
(b) Construction and removal of forms and reshoring;
(c) Placing of reinforcement and anchors; Inspection in no way relieves the contractor from the obligation
to follow the plans and specifications and to provide the
(d) Mixing, placing, and curing of concrete; designated quality and quantity of materials and workman-
ship for all job stages. Some of the information regarding
(e) Sequence of erection and connection of precast designated concrete mixtures on a project is often provided
members; in a preconstruction submittal to the licensed design profes-
(f) Tensioning of tendons; sional. For instance, concrete mixture ingredients and
composition are often described in detail in the submittal
(g) Any significant construction loadings on and are subsequently identified by a mixture designation
completed floors, members, or walls; (reflected on a delivery ticket) that can also identify the
placement location in the structure. The inspector should be
(h) General progress of Work. present as frequently as necessary to judge whether the
quality, as measured by quality assurance tests, quantity, and
placement of the concrete comply with the contract docu-
ments; to counsel on possible ways of obtaining the desired
results; to see that the general system proposed for form-
work appears proper (though it remains the contractor’s
responsibility to design and build adequate forms and to
leave them in place until it is safe to remove them); to see
that reinforcement is properly installed; to see that concrete
is delivered as required and is of the correct quality, properly
placed, and cured; and to see that tests for quality assurance
are being made as specified.
1.3.3 — When the ambient temperature falls below R1.3.3 — The term “ambient temperature” means the
4 °C or rises above 35 °C a record shall be kept of temperature of the environment to which the concrete is
concrete temperatures and of protection given to directly exposed. Concrete temperature as used in this
concrete during placement and curing. section may be taken as the surface temperature of the
CODE COMMENTARY 1
concrete. Surface temperatures may be determined by
placing temperature sensors in contact with concrete
surfaces or between concrete surfaces and covers used for
curing, such as insulation blankets or plastic sheeting.
1.3.4 — Records of inspection required in 1.3.2 and R1.3.4 — A record of inspection in the form of a job diary is
1.3.3 shall be preserved by the inspecting engineer or required in case questions subsequently arise concerning the
architect for 2 years after completion of the project. performance or safety of the structure or members. Photo-
graphs documenting job progress may also be desirable.
1.3.5 — For special moment frames designed in R1.3.5 — The purpose of this section is to ensure that the
accordance with Chapter 21, continuous inspection of detailing required in special moment frames is properly
the placement of the reinforcement and concrete shall executed through inspection by personnel who are qualified
be made by a qualified inspector. The inspector shall to do this Work. Qualifications of inspectors should be accept-
be under the supervision of the licensed design able to the jurisdiction enforcing the general building code.
professional responsible for the structural design or
under the supervision of a licensed design profes-
sional with demonstrated capability for supervising
inspection of construction of special moment frames.
Sponsors of any system of design or construction New methods of design, new materials, and new uses of
within the scope of this Code, the adequacy of which materials should undergo a period of development before
has been shown by successful use or by analysis or being specifically covered in a code. Hence, good systems
test, but which does not conform to or is not covered or components might be excluded from use by implication if
by this Code, shall have the right to present the data means were not available to obtain acceptance.
on which their design is based to the building official or
to a board of examiners appointed by the building official. For special systems considered under this section, specific
This board shall be composed of competent engineers tests, load factors, deflection limits, and other pertinent
and shall have authority to investigate the data so requirements should be set by the board of examiners, and
submitted, to require tests, and to formulate rules should be consistent with the intent of the Code.
governing design and construction of such systems to
meet the intent of this Code. These rules, when The provisions of this section do not apply to model tests
approved by the building official and promulgated, used to supplement calculations under 1.2.2 or to strength
shall be of the same force and effect as the provisions evaluation of existing structures under Chapter 20.
of this Code.
As,min = minimum area of flexural reinforcement, bt = width of that part of cross section containing
mm2, see 10.5, Chapter 10 the closed stirrups resisting torsion, mm,
Ast = total area of nonprestressed longitudinal Chapter 11
2 reinforcement (bars or steel shapes), mm2, bv = width of cross section at contact surface
Chapters 10, 21 being investigated for horizontal shear, mm,
Asx = area of structural steel shape, pipe, or tubing Chapter 17
in a composite section, mm2, Chapter 10 bw = web width, or diameter of circular section,
At = area of one leg of a closed stirrup resisting mm, Chapters 10-12, 21, 22, Appendix B
torsion within spacing s, mm2, Chapter 11 b1 = dimension of the critical section bo measured
Atp = area of prestressing steel in a tie, mm2, in the direction of the span for which
Appendix A moments are determined, mm, Chapter 13
Atr = total cross-sectional area of all transverse b2 = dimension of the critical section bo measured
reinforcement within spacing s that crosses in the direction perpendicular to b1, mm,
the potential plane of splitting through the Chapter 13
reinforcement being developed, mm2, Bn = nominal bearing strength, N, Chapter 22
Chapter 12 Bu = factored bearing load, N, Chapter 22
Ats = area of nonprestressed reinforcement in a c = distance from extreme compression fiber to
tie, mm2, Appendix A neutral axis, mm, Chapters 9, 10, 14, 21
Av = area of shear reinforcement spacing s, mm2, cac = critical edge distance required to develop the
Chapters 11, 17 basic concrete breakout strength of a post-
AVc = projected concrete failure area of a single installed anchor in uncracked concrete
anchor or group of anchors, for calculation of without supplementary reinforcement to
strength in shear, mm2, see D.6.2.1, control splitting, mm, see D.8.6, Appendix D
Appendix D ca,max = maximum distance from center of an anchor
AVco = projected concrete failure area of a single shaft to the edge of concrete, mm, Appendix D
anchor, for calculation of strength in shear, if ca,min = minimum distance from center of an anchor
not limited by corner influences, spacing, or shaft to the edge of concrete, mm, Appendix D
member thickness, mm2, see D.6.2.1, ca1 = distance from the center of an anchor shaft
Appendix D to the edge of concrete in one direction, mm.
Avd = total area of reinforcement in each group of If shear is applied to anchor, ca1 is taken in
diagonal bars in a diagonally reinforced the direction of the applied shear. If tension
coupling beam, mm2, Chapter 21 is applied to the anchor, ca1 is the minimum
Avf = area of shear-friction reinforcement, mm2, edge distance, Appendix D
Chapters 11, 21 ca2 = distance from center of an anchor shaft to
Avh = area of shear reinforcement parallel to flex- the edge of concrete in the direction perpen-
ural tension reinforcement within spacing s2, dicular to ca1, mm, Appendix D
mm2, Chapter 11 cb = smaller of: (a) the distance from center of a
Av,min = minimum area of shear reinforcement within bar or wire to nearest concrete surface, and
spacing s, mm2, see 11.4.6.3 and 11.4.6.4, (b) one-half the center-to-center spacing of
Chapter 11 bars or wires being developed, mm, Chapter 12
A1 = loaded area, mm2, Chapters 10, 22 cc = clear cover of reinforcement, mm, see
A2 = area of the lower base of the largest frustum 10.6.4, Chapter 10
of a pyramid, cone, or tapered wedge ct = distance from the interior face of the column
contained wholly within the support and to the slab edge measured parallel to c1, but
having for its upper base the loaded area, not exceeding c1, mm, Chapter 21
and having side slopes of 1 vertical to 2 c1 = dimension of rectangular or equivalent
horizontal, mm2 , Chapters 10, 22 rectangular column, capital, or bracket
b = width of compression face of member, mm, measured in the direction of the span for
Chapter 10, Appendix B which moments are being determined, mm,
bc = cross-sectional dimension of member core Chapters 11, 13, 21
measured to the outside edges of the trans- c2 = dimension of rectangular or equivalent
verse reinforcement composing area Ash , mm, rectangular column, capital, or bracket
Chapter 21 measured in the direction perpendicular to
bo = perimeter of critical section for shear in slabs c1, mm, Chapter 13
and footings, mm, see 11.11.1.2, Chapters 11, C = cross-sectional constant to define torsional
22 properties of slab and beam, see 13.6.4.2,
bs = width of strut, mm, Appendix A Chapter 13
loads using gross section properties, MPa, about centroidal axis defined for calculating
see 18.3.3, Chapter 18 αf and βt , mm4, Chapter 13
futa = specified tensile strength of anchor steel, Ise = moment of inertia of reinforcement about
2 MPa, Appendix D centroidal axis of member cross section,
fy = specified yield strength of reinforcement, mm4, Chapter 10
MPa, Chapters 3, 7, 9-12, 14, 17-19, 21, Isx = moment of inertia of structural steel shape,
Appendixes A-C pipe, or tubing about centroidal axis of
fya = specified yield strength of anchor steel, MPa, composite member cross section, mm4,
Appendix D Chapter 10
fyt = specified yield strength fy of transverse k = effective length factor for compression
reinforcement, MPa, Chapters 10-12, 21 members, Chapters 10, 14
F = loads due to weight and pressures of fluids kc = coefficient for basic concrete breakout
with well-defined densities and controllable strength in tension, Appendix D
maximum heights, or related internal kcp = coefficient for pryout strength, Appendix D
moments and forces, Chapter 9, Appendix C K = wobble friction coefficient per meter of
Fn = nominal strength of a strut, tie, or nodal tendon, Chapter 18
zone, N, Appendix A Ktr = transverse reinforcement index, see 12.2.3,
Fnn = nominal strength at face of a nodal zone, N, Chapter 12
Appendix A l = span length of beam or one-way slab; clear
Fns = nominal strength of a strut, N, Appendix A projection of cantilever, mm, see 8.7, Chapter 9
Fnt = nominal strength of a tie, N, Appendix A la = additional embedment length beyond center-
Fu = factored force acting in a strut, tie, bearing line of support or point of inflection, mm,
area, or nodal zone in a strut-and-tie model, Chapter 12
N, Appendix A lc = length of compression member in a frame,
h = overall thickness or height of member, mm, measured center-to-center of the joints in the
Chapters 9-12, 14, 17, 18, 20-22, Appen- frame, mm, Chapters 10, 14, 22
dixes A, C ld = development length in tension of deformed
ha = thickness of member in which an anchor is bar, deformed wire, plain and deformed
located, measured parallel to anchor axis, welded wire reinforcement, or pretensioned
mm, Appendix D strand, mm, Chapters 7, 12, 19, 21
hef = effective embedment depth of anchor, mm, ldc = development length in compression of
see D.8.5, Appendix D deformed bars and deformed wire, mm,
hv = depth of shearhead cross section, mm, Chapter 12
Chapter 11 ldh = development length in tension of deformed
hw = height of entire wall from base to top or bar or deformed wire with a standard hook,
height of the segment of wall considered, measured from critical section to outside end
mm, Chapters 11, 21 of hook (straight embedment length between
hx = maximum center-to-center horizontal critical section and start of hook [point of
spacing of crossties or hoop legs on all faces tangency] plus inside radius of bend and one
of the column, mm, Chapter 21 bar diameter), mm, see 12.5 and 21.7.5,
H = loads due to weight and pressure of soil, Chapters 12, 21
water in soil, or other materials, or related ldt = development length in tension of headed
internal moments and forces, Chapter 9, deformed bar, measured from the critical
Appendix C section to the bearing face of the head, mm,
I = moment of inertia of section about centroidal see 12.6, Chapter 12
axis, mm4, Chapters 10, 11 le = load bearing length of anchor for shear, mm,
Ib = moment of inertia of gross section of beam see D.6.2.2, Appendix D
about centroidal axis, mm4, see 13.6.1.6, ln = length of clear span measured face-to-face of
Chapter 13 supports, mm, Chapters 8-11, 13, 16, 18, 21
Icr = moment of inertia of cracked section trans- lo = length, measured from joint face along axis
formed to concrete, mm4 , Chapter 9 of structural member, over which special
Ie = effective moment of inertia for computation of transverse reinforcement must be
deflection, mm4, see 9.5.2.3, Chapter 9 provided, mm, Chapter 21
Ig = moment of inertia of gross concrete section lpx = distance from jacking end of prestressing
about centroidal axis, neglecting reinforcement, steel element to point under consideration,
mm4,Chapters 9, 10, 14 m, see 18.6.2, Chapter 18
Is = moment of inertia of gross section of slab lt = span of member under load test, taken as
the shorter span for two-way slab systems, assuming a tensile stress in the longitudinal
mm. Span is the smaller of: (a) distance bars of at least 1.25fy and a strength reduction
between centers of supports, and (b) clear factor, φ, of 1.0, N⋅mm, Chapter 21
distance between supports plus thickness h Ms = factored moment due to loads causing 2
of member. Span for a cantilever shall be appreciable sway, N⋅mm, Chapter 10
taken as twice the distance from face of Mslab = portion of slab factored moment balanced by
support to cantilever end, Chapter 20 support moment, N⋅mm, Chapter 21
lu = unsupported length of compression member, Mu = factored moment at section, N⋅mm, Chapters
mm, see 10.10.1.1, Chapter 10 10, 11, 13, 14, 21, 22
lv = length of shearhead arm from centroid of Mua = moment at midheight of wall due to factored
concentrated load or reaction, mm, Chapter 11 lateral and eccentric vertical loads, not
lw = length of entire wall or length of segment of including PΔ effects, N⋅mm, Chapter 14
wall considered in direction of shear force, Mv = moment resistance contributed by shear-
mm, Chapters 11, 14, 21 head reinforcement, N⋅mm, Chapter 11
l1 = length of span in direction that moments are M1 = smaller factored end moment on a compres-
being determined, measured center-to- sion member, to be taken as positive if
center of supports, mm, Chapter 13 member is bent in single curvature, and
l2 = length of span in direction perpendicular to negative if bent in double curvature, N⋅mm,
l1, measured center-to-center of supports, Chapter 10
mm, see 13.6.2.3 and 13.6.2.4, Chapter 13 M1ns = factored end moment on a compression
L = live loads, or related internal moments and member at the end at which M1 acts, due to
forces, Chapters 8, 9, 20, 21, Appendix C loads that cause no appreciable sidesway,
Lr = roof live load, or related internal moments calculated using a first-order elastic frame
and forces, Chapter 9 analysis, N⋅mm, Chapter 10
Ma = maximum moment in member due to service M1s = factored end moment on compression
loads at stage deflection is computed, N⋅mm, member at the end at which M1 acts, due to
Chapters 9, 14 loads that cause appreciable sidesway,
Mc = factored moment amplified for the effects of calculated using a first-order elastic frame
member curvature used for design of analysis, N⋅mm, Chapter 10
compression member, N⋅mm, see 10.10.6, M2 = larger factored end moment on compression
Chapter 10 member. If transverse loading occurs
Mcr = cracking moment, N⋅mm, see 9.5.2.3, between supports, M2 is taken as the largest
Chapters 9, 14 moment occurring in member. Value of M2 is
Mcre = moment causing flexural cracking at section always positive, N⋅mm, Chapter 10
due to externally applied loads, N⋅mm, M2,min = minimum value of M2, N⋅mm, Chapter 10
Chapter 11 M2ns = factored end moment on compression
Mm = factored moment modified to account for member at the end at which M2 acts, due to
effect of axial compression, N⋅mm, see loads that cause no appreciable sidesway,
11.2.2.2, Chapter 11 calculated using a first-order elastic frame
Mmax = maximum factored moment at section due to analysis, N⋅mm, Chapter 10
externally applied loads, N⋅mm, Chapter 11 M2s = factored end moment on compression
Mn = nominal flexural strength at section, N⋅mm, member at the end at which M2 acts, due to
Chapters 11, 12, 14, 18, 21, 22 loads that cause appreciable sidesway,
Mnb = nominal flexural strength of beam including calculated using a first-order elastic frame
slab where in tension, framing into joint, analysis, N⋅mm, Chapter 10
N⋅mm, see 21.6.2.2, Chapter 21 n = number of items, such as strength tests,
Mnc = nominal flexural strength of column framing bars, wires, monostrand anchorage devices,
into joint, calculated for factored axial force, anchors, or shearhead arms, Chapters 5, 11,
consistent with the direction of lateral forces 12, 18, Appendix D
considered, resulting in lowest flexural Nb = basic concrete breakout strength in tension
strength, N⋅mm, see 21.6.2.2, Chapter 21 of a single anchor in cracked concrete, N,
Mo = total factored static moment, N⋅mm, Chapter 13 see D.5.2.2, Appendix D
Mp = required plastic moment strength of shear- Nc = tension force in concrete due to unfactored
head cross section, N⋅mm, Chapter 11 dead load plus live load, N, Chapter 18
Mpr = probable flexural strength of members, with Ncb = nominal concrete breakout strength in
or without axial load, determined using the tension of a single anchor, N, see D.5.2.1,
properties of the member at the joint faces Appendix D
Ncbg = nominal concrete breakout strength in Q = stability index for a story, see 10.10.5.2,
tension of a group of anchors, N, see Chapter 10
D.5.2.1, Appendix D r = radius of gyration of cross section of a
2 Nn = nominal strength in tension, N, Appendix D compression member, mm, Chapter 10
Np = pullout strength in tension of a single anchor R = rain load, or related internal moments and
in cracked concrete, N, see D.5.3.4 and forces, Chapter 9
D.5.3.5, Appendix D s = center-to-center spacing of items, such as
Npn = nominal pullout strength in tension of a longitudinal reinforcement, transverse
single anchor, N, see D.5.3.1, Appendix D reinforcement, prestressing tendons, wires,
Nsa = nominal strength of a single anchor or group or anchors, mm, Chapters 10-12, 17-21,
of anchors in tension as governed by the Appendix D
steel strength, N, see D.5.1.1 and D.5.1.2, si = center-to-center spacing of reinforcement in
Appendix D the i-th layer adjacent to the surface of the
Nsb = side-face blowout strength of a single member, mm, Appendix A
anchor, N, Appendix D so = center-to-center spacing of transverse rein-
Nsbg = side-face blowout strength of a group of forcement within the length lo , mm, Chapter 21
anchors, N, Appendix D ss = sample standard deviation, MPa, Chapter 5,
Nu = factored axial force normal to cross section Appendix D
occurring simultaneously with Vu or Tu ; to be s2 = center-to-center spacing of longitudinal shear
taken as positive for compression and or torsion reinforcement, mm, Chapter 11
negative for tension, N, Chapter 11 S = snow load, or related internal moments and
Nua = factored tensile force applied to anchor or forces, Chapters 9, 21
group of anchors, N, Appendix D Se = moment, shear, or axial force at connection
Nuc = factored horizontal tensile force applied at corresponding to development of probable
top of bracket or corbel acting simulta- strength at intended yield locations, based
neously with Vu , to be taken as positive for on the governing mechanism of inelastic
tension, N, Chapter 11 lateral deformation, considering both gravity
pcp = outside perimeter of concrete cross section, and earthquake load effects, Chapter 21
mm, see 11.5.1, Chapter 11 Sm = elastic section modulus, mm3, Chapter 22
ph = perimeter of centerline of outermost closed Sn = nominal flexural, shear, or axial strength of
transverse torsional reinforcement, mm, connection, Chapter 21
Chapter 11 Sy = yield strength of connection, based on fy , for
Pb = nominal axial strength at balanced strain moment, shear, or axial force, Chapter 21
conditions, N, see 10.3.2, Chapters 9, 10, t = wall thickness of hollow section, mm,
Appendixes B, C Chapter 11
Pc = critical buckling load, N, see 10.10.6, T = cumulative effect of temperature, creep,
Chapter 10 shrinkage, differential settlement, and
Pn = nominal axial strength of cross section, N, shrinkage-compensating concrete, Chapter 9,
Chapters 9, 10, 14, 22, Appendixes B, C Appendix C
Pn,max = maximum allowable value of Pn, N, see Tn = nominal torsional moment strength, N⋅mm,
10.3.6, Chapter 10 Chapter 11
Po = nominal axial strength at zero eccentricity, N, Tu = factored torsional moment at section, N⋅mm,
Chapter 10 Chapter 11
Ppj = prestressing force at jacking end, N, Chapter 18 U = required strength to resist factored loads or
Ppu = factored prestressing force at anchorage related internal moments and forces,
device, N, Chapter 18 Chapter 9, Appendix C
Ppx = prestressing force evaluated at distance lpx vn = nominal shear stress, MPa, see 11.11.6.2,
from the jacking end, N, Chapter 18 Chapters 11, 21
Ps = unfactored axial load at the design Vb = basic concrete breakout strength in shear of
(midheight) section including effects of self- a single anchor in cracked concrete, N, see
weight, N, Chapter 14 D.6.2.2 and D.6.2.3, Appendix D
Pu = factored axial force; to be taken as positive Vc = nominal shear strength provided by
for compression and negative for tension, N, concrete, N, Chapters 8, 11, 13, 21
Chapters 10, 14, 21, 22 Vcb = nominal concrete breakout strength in shear
qDu = factored dead load per unit area, Chapter 13 of a single anchor, N, see D.6.2.1, Appendix D
qLu = factored live load per unit area, Chapter 13 Vcbg = nominal concrete breakout strength in shear of
qu = factored load per unit area, Chapter 13 a group of anchors, N, see D.6.2.1, Appendix D
Vci = nominal shear strength provided by concrete concrete strength to nominal wall shear
when diagonal cracking results from strength, see 21.9.4.1, Chapter 21
combined shear and moment, N, Chapter 11 αf = ratio of flexural stiffness of beam section to
Vcp = nominal concrete pryout strength of a single flexural stiffness of a width of slab bounded 2
anchor, N, see D.6.3.1, Appendix D laterally by centerlines of adjacent panels (if
Vcpg = nominal concrete pryout strength of a group any) on each side of the beam, see 13.6.1.6,
of anchors, N, see D.6.3.1, Appendix D Chapters 9, 13
Vcw = nominal shear strength provided by concrete αfm = average value of αf for all beams on edges of
when diagonal cracking results from high a panel, Chapter 9
principal tensile stress in web, N, Chapter 11 αf1 = αf in direction of l1, Chapter 13
Vd = shear force at section due to unfactored αf2 = αf in direction of l2, Chapter 13
dead load, N, Chapter 11 αi = angle between the axis of a strut and the
Ve = design shear force corresponding to the bars in the i-th layer of reinforcement
development of the probable moment crossing that strut, Appendix A
strength of the member, N, see 21.5.4.1 and αpx = total angular change of tendon profile from
21.6.5.1, Chapter 21 tendon jacking end to point under consider-
Vi = factored shear force at section due to externally ation, radians, Chapter 18
applied loads occurring simultaneously with αs = constant used to compute Vc in slabs and
Mmax , N, Chapter 11 footings, Chapter 11
Vn = nominal shear strength, N, Chapters 8, 10, αv = ratio of flexural stiffness of shearhead arm to
11, 21, 22, Appendix D that of the surrounding composite slab
Vnh = nominal horizontal shear strength, N, section, see 11.11.4.5, Chapter 11
Chapter 17 β = ratio of long to short dimensions: clear spans
Vp = vertical component of effective prestress for two-way slabs, see 9.5.3.3 and 22.5.4;
force at section, N, Chapter 11 sides of column, concentrated load or reaction
Vs = nominal shear strength provided by shear area, see 11.11.2.1; or sides of a footing,
reinforcement, N, Chapter 11 see 15.4.4.2, Chapters 9, 11, 15, 22
Vsa = nominal strength in shear of a single anchor βb = ratio of area of reinforcement cut off to total
or group of anchors as governed by the steel area of tension reinforcement at section,
strength, N, see D.6.1.1 and D.6.1.2, Chapter 12
Appendix D βdns = ratio used to account for reduction of stiff-
Vu = factored shear force at section, N, Chapters ness of columns due to sustained axial
11-13, 17, 21, 22 loads, see 10.10.6.2, Chapter 10
Vua = factored shear force applied to a single βds = ratio used to account for reduction of stiffness
anchor or group of anchors, N, Appendix D of columns due to sustained lateral loads,
Vug = factored shear force on the slab critical see 10.10.4.2, Chapter 10
section for two-way action due to gravity βn = factor to account for the effect of the
loads, N, see 21.13.6 anchorage of ties on the effective compressive
Vus = factored horizontal shear in a story, N, strength of a nodal zone, Appendix A
Chapter 10 βp = factor used to compute Vc in prestressed
wc = density (unit weight) of normalweight slabs, Chapter 11
concrete or equilibrium density of light- βs = factor to account for the effect of cracking
weight concrete, kg/m3 , Chapters 8, 9 and confining reinforcement on the effective
wu = factored load per unit length of beam or one- compressive strength of the concrete in a
way slab, Chapter 8 strut, Appendix A
W = wind load, or related internal moments and βt = ratio of torsional stiffness of edge beam
forces, Chapter 9, Appendix C section to flexural stiffness of a width of slab
x = shorter overall dimension of rectangular part equal to span length of beam, center-to-
of cross section, mm, Chapter 13 center of supports, see 13.6.4.2, Chapter 13
y = longer overall dimension of rectangular part β1 = factor relating depth of equivalent rectan-
of cross section, mm, Chapter 13 gular compressive stress block to neutral
yt = distance from centroidal axis of gross axis depth, see 10.2.7.3, Chapters 10, 18,
section, neglecting reinforcement, to tension Appendix B
face, mm, Chapters 9, 11 γf = factor used to determine the unbalanced
α = angle defining the orientation of reinforce- moment transferred by flexure at slab-column
ment, Chapters 11, 21, Appendix A connections, see 13.5.3.2, Chapters 11,
αc = coefficient defining the relative contribution of 13, 21
γp = factor for type of prestressing steel, see all relative to normalweight concrete of the
18.7.2, Chapter 18 same compressive strength, see 8.6.1,
γs = factor used to determine the portion of 11.6.4.3, 12.2.4(d), 12.5.2, Chapters 9, 11,
2 reinforcement located in center band of 12,19, 21, 22, and Appendixes A, D
footing, see 15.4.4.2, Chapter 15 λΔ = multiplier for additional deflection due to
γv = factor used to determine the unbalanced long-term effects, see 9.5.2.5, Chapter 9
moment transferred by eccentricity of shear μ = coefficient of friction, see 11.6.4.3, Chapters
at slab-column connections, see 11.11.7.1, 11, 21
Chapter 11 μp = post-tensioning curvature friction coefficient,
δ = moment magnification factor to reflect effects Chapter 18
of member curvature between ends of ξ = time-dependent factor for sustained load,
compression member, Chapter 10 see 9.5.2.5, Chapter 9
δs = moment magnification factor for frames not ρ = ratio of As to bd, Chapters 11, 13, 21,
braced against sidesway, to reflect lateral Appendix B
drift resulting from lateral and gravity loads, ρ′ = ratio of As′ to bd, Chapter 9, Appendix B
Chapter 10 ρb = ratio of As to bd producing balanced strain
δu = design displacement, mm, Chapter 21 conditions, see 10.3.2, Chapters 10, 13, 14,
Δcr = computed, out-of-plane deflection at Appendix B
midheight of wall corresponding to cracking ρl = ratio of area of distributed longitudinal
moment, Mcr , mm, Chapter 14 reinforcement to gross concrete area
Δfp = increase in stress in prestressing steel due perpendicular to that reinforcement ,
to factored loads, MPa, Appendix A Chapters 11, 14, 21
Δfps = stress in prestressing steel at service loads ρp = ratio of Aps to bdp , Chapter 18
less decompression stress, MPa, Chapter 18 ρs = ratio of volume of spiral reinforcement to
Δn = computed, out-of-plane deflection at total volume of core confined by the spiral
midheight of wall corresponding to nominal (measured out-to-out of spirals), Chapters
flexural strength, Mn , mm, Chapter 14 10, 21
Δo = relative lateral deflection between the top ρt = ratio of area distributed transverse reinforce-
and bottom of a story due to lateral forces ment to gross concrete area perpendicular to
computed using a first-order elastic frame that reinforcement, Chapters 11, 14, 21
analysis and stiffness values satisfying ρv = ratio of tie reinforcement area to area of
10.10.5.2, mm, Chapter 10 contact surface, see 17.5.3.3, Chapter 17
Δr = difference between initial and final (after load ρw = ratio of As to bwd, Chapter 11
removal) deflections for load test or repeat φ = strength reduction factor, see 9.3, Chapters
load test, mm, Chapter 20 8-11, 13, 14, 17-22, Appendixes A-D
Δs = computed, out-of-plane deflection at ψc,N = factor used to modify tensile strength of
midheight of wall due to service loads, mm, anchors based on presence or absence of
Chapter 14 cracks in concrete, see D.5.2.6, Appendix D
Δu = computed deflection at midheight of wall due ψc,P = factor used to modify pullout strength of
to factored loads, mm, Chapter 14 anchors based on presence or absence of
Δ1 = measured maximum deflection during first cracks in concrete, see D.5.3.6, Appendix D
load test, mm, see 20.5.2, Chapter 20 ψc,V = factor used to modify shear strength of
Δ2 = maximum deflection measured during anchors based on presence or absence of
second load test relative to the position of cracks in concrete and presence or absence
the structure at the beginning of second load of supplementary reinforcement, see D.6.2.7
test, mm, see 20.5.2, Chapter 20 for anchors in shear, Appendix D
εt = net tensile strain in extreme layer of longitudinal ψcp,N = factor used to modify tensile strength of post-
tension steel at nominal strength, excluding installed anchors intended for use in
strains due to effective prestress, creep, uncracked concrete without supplementary
shrinkage, and temperature, Chapters 8-10, reinforcement, see D.5.2.7, Appendix D
Appendix C ψe = factor used to modify development length
θ = angle between axis of strut, compression based on reinforcement coating, see 12.2.4,
diagonal, or compression field and the Chapter 12
tension chord of the member, Chapter 11, ψec,N = factor used to modify tensile strength of
Appendix A anchors based on eccentricity of applied
λ = modification factor reflecting the reduced loads, see D.5.2.4, Appendix D
mechanical properties of lightweight concrete, ψec,V = factor used to modify shear strength of
CODE COMMENTARY
2.2 — Definitions R2.2 — Definitions
2
The following terms are defined for general use in this For consistent application of the Code, it is necessary that
Code. Specialized definitions appear in individual terms be defined where they have particular meanings in the
chapters. Code. The definitions given are for use in application of this
Code only and do not always correspond to ordinary usage.
Admixture — Material other than water, aggregate, or A glossary of most-used terms relating to cement manufac-
hydraulic cement, used as an ingredient of concrete turing, concrete design and construction, and research in
and added to concrete before or during its mixing to concrete is contained in “Cement and Concrete Termi-
modify its properties. nology” available on the ACI website.
Anchorage device — In post-tensioning, the hard- Anchorage device — Most anchorage devices for post-
ware used for transferring a post-tensioning force from tensioning are standard manufactured devices available
the prestressing steel to the concrete. from commercial sources. In some cases, “special” details
or assemblages are developed that combine various wedges
and wedge plates for anchoring prestressing steel. These
informal designations as standard anchorage devices or
special anchorage devices have no direct relation to the
Code and AASHTO “Standard Specifications for Highway
Bridges” classification of anchorage devices as Basic
Anchorage Devices or Special Anchorage Devices.
Anchorage zone — In post-tensioned members, the Anchorage zone — The terminology “ahead of” and “behind”
portion of the member through which the concen- the anchorage device is illustrated in Fig. R18.13.1(b).
trated prestressing force is transferred to the
concrete and distributed more uniformly across the
section. Its extent is equal to the largest dimension
of the cross section. For anchorage devices located
away from the end of a member, the anchorage
zone includes the disturbed regions ahead of and
behind the anchorage devices.
Basic monostrand anchorage device — Anchorage Basic anchorage devices — Devices that are so propor-
device used with any single strand or a single 15 mm tioned that they can be checked analytically for compliance
or smaller diameter bar that satisfies 18.21.1 and the with bearing stress and stiffness requirements without
anchorage device requirements of ACI 423.7. having to undergo the acceptance-testing program required
of special anchorage devices.
CODE COMMENTARY
Basic multistrand anchorage device — Anchorage
device used with multiple strands, bars, or wires, or with 2
single bars larger than 15 mm diameter, that satisfies
18.21.1 and the bearing stress and minimum plate
stiffness requirements of AASHTO Bridge Specifica-
tions, Division I, Articles 9.21.7.2.2 through 9.21.7.2.4.
Building official — The officer or other designated Building official — The term used by many general
authority charged with the administration and enforce- building codes to identify the person charged with adminis-
ment of this Code, or a duly authorized representative. tration and enforcement of provisions of the building code.
Such terms as building commissioner or building inspector
are variations of the title and the term “building official” as
used in this Code, is intended to include those variations, as
well as others that are used in the same sense.
Column — Member with a ratio of height-to-least Column — The term “compression member” is used in the
lateral dimension exceeding 3 used primarily to Code to define any member in which the primary stress is
support axial compressive load. For a tapered longitudinal compression. Such a member need not be
member, the least lateral dimension is the average of vertical but may have any orientation in space. Bearing walls,
the top and bottom dimensions of the smaller side. columns, and pedestals qualify as compression members
under this definition.
CODE COMMENTARY
While a wall always encloses or separates spaces, it may
2 also be used to resist horizontal or vertical forces or
bending. For example, a retaining wall or a basement wall
also supports various combinations of loads.
Concrete, lightweight — Concrete containing light- Concrete, lightweight — In 2000, ASTM C567 adopted
weight aggregate and an equilibrium density, as deter- “equilibrium density” as the measure for determining
mined by ASTM C567, between 1140 and 1840 kg/m3. compliance with specified in-service density requirements.
According to ASTM C567, equilibrium density may be
determined by measurement or approximated by calculation
using either the measured oven-dry density or the oven-dry
density calculated from the mixture proportions. Unless spec-
ified otherwise, ASTM C567 requires that equilibrium density
be approximated by calculation.
CODE COMMENTARY
Concrete, normalweight — Concrete containing only Concrete, normalweight — Normalweight concrete typi-
aggregate that conforms to ASTM C33. cally has a density (unit weight) between 2155 and 2555 kg/m3, 2
and is normally taken as 2315 to 2400 kg/m3.
Cover, specified concrete — The distance between Cover, specified concrete — Tolerances on specified concrete
the outermost surface of embedded reinforcement and cover are provided in 7.5.2.1.
the closest outer surface of the concrete indicated on
design drawings or in project specifications.
CODE COMMENTARY
Deformed reinforcement — Deformed reinforcing bars, Deformed reinforcement — Deformed reinforcement is
2 bar mats, deformed wire, and welded wire reinforcement defined as that meeting the deformed reinforcement specifi-
conforming to 3.5.3. cations of 3.5.3.1, or the specifications of 3.5.3.3, 3.5.3.4,
3.5.3.5, 3.5.3.6, or 3.5.3.7. No other reinforcement qualifies.
This definition permits accurate statement of anchorage
lengths. Bars or wire not meeting the deformation require-
ments or welded wire reinforcement not meeting the
spacing requirements are “plain reinforcement,” for code
purposes, and may be used only for spirals.
Design displacement — Total lateral displacement Design displacement — The design displacement is an
expected for the design-basis earthquake, as required index of the maximum lateral displacement expected in
by the governing code for earthquake-resistant design. design for the design-basis earthquake. In documents such
See Chapter 21. as ASCE/SEI 7-05 and the 2006 International Building
Code, the design displacement is calculated using static or
dynamic linear elastic analysis under code-specified actions
considering effects of cracked sections, effects of torsion,
effects of vertical forces acting through lateral displacements,
and modification factors to account for expected inelastic
response. The design displacement generally is larger than
the displacement calculated from design-level forces
applied to a linear-elastic model of the building.
CODE COMMENTARY
Equilibrium density — Density of lightweight
concrete after exposure to a relative humidity of 50 2
± 5 percent and a temperature of 23 ± 2 °C for a
period of time sufficient to reach constant density (see
ASTM C567).
Headed deformed bars — Deformed reinforcing bars Headed deformed bars — The bearing area of a headed
with heads attached at one or both ends. Heads are deformed bar is, for the most part, perpendicular to the bar
attached to the bar end by means such as welding or axis, as shown in Fig. R3.5.9. In contrast, the bearing area of
forging onto the bar, internal threads on the head the head of headed stud reinforcement is a nonplanar spatial
mating to threads on the bar end, or a separate surface of revolution, as shown in Fig. R3.5.5. The two types
threaded nut to secure the head of the bar. The net of reinforcement differ in other ways. The shanks of headed
bearing area of headed deformed bar equals the gross studs are smooth, not deformed as with headed deformed
area of the head minus the larger of the area of the bar bars. The minimum net bearing area of the head of a headed
and the area of any obstruction. deformed bar is permitted to be as small as four times the bar
area. In contrast, the minimum stud head area is not specified
in terms of the bearing area, but by the total head area which
must be at least 10 times the area of the shank.
CODE COMMENTARY
licensing laws of the state or jurisdiction in which the
2 project is to be constructed and who is in responsible
charge of the structural design; in other documents,
also referred to as registered design professional.
Load, dead — Dead weight supported by a member, Loads — A number of definitions for loads are given as the
as defined by general building code of which this Code Code contains requirements that are to be met at various
forms a part (without load factors). load levels. The terms “dead load” and “live load” refer to
the unfactored loads (service loads) specified or defined by
Load, factored — Load, multiplied by appropriate load the general building code. Service loads (loads without load
factors, used to proportion members by the strength factors) are to be used where specified in the Code to propor-
design method of this Code. See 8.1.1 and 9.2. tion or investigate members for adequate serviceability, as
in 9.5, Control of Deflections. Loads used to proportion a
Load, live — Live load specified by general building member for adequate strength are defined as factored loads.
code of which this Code forms a part (without load Factored loads are service loads multiplied by the appro-
factors). priate load factors specified in 9.2 for required strength. The
term “design loads,” as used in the 1971 Code edition to
Load, service — Load specified by general building refer to loads multiplied by the appropriate load factors, was
code of which this Code forms a part (without load discontinued in the 1977 Code to avoid confusion with the
factors). design load terminology used in general building codes to
denote service loads, or posted loads in buildings. The
factored load terminology, first adopted in the 1977 Code,
clarifies when the load factors are applied to a particular
load, moment, or shear value as used in the Code provisions.
CODE COMMENTARY
Pedestal — Member with a ratio of height-to-least Pedestal — In the 2008 Code, the definitions for column
lateral dimension less than or equal to 3 used primarily and pedestal were revised to provide consistency between 2
to support axial compressive load. For a tapered the definitions.
member, the least lateral dimension is the average of
the top and bottom dimensions of the smaller side.
Plain concrete — Structural concrete with no reinforce- Plain concrete — The presence of reinforcement
ment or with less reinforcement than the minimum (nonprestressed or prestressed) does not prohibit the
amount specified for reinforced concrete. member from being classified as plain concrete, provided all
requirements of Chapter 22 are satisfied.
Prestressed concrete — Structural concrete in which Prestressed concrete — Reinforced concrete is defined to
internal stresses have been introduced to reduce include prestressed concrete. Although the behavior of a
potential tensile stresses in concrete resulting from prestressed member with unbonded tendons may vary from
loads. that of members with continuously bonded tendons, bonded
and unbonded prestressed concrete are combined with
conventionally reinforced concrete under the generic term
“reinforced concrete.” Provisions common to both prestressed
and conventionally reinforced concrete are integrated to avoid
overlapping and conflicting provisions.
CODE COMMENTARY
Reinforcement — Material that conforms to 3.5,
2 excluding prestressing steel unless specifically
included.
Sheathing — A material encasing prestressing steel Sheathing — Typically, sheathing is a continuous, seam-
to prevent bonding of the prestressing steel with the less, high-density polyethylene material extruded directly
surrounding concrete, to provide corrosion protection, on the coated prestressing steel.
and to contain the corrosion inhibiting coating.
Special anchorage device — Anchorage device that Special anchorage devices — Special anchorage devices
satisfies 18.15.1 and the standardized acceptance are any devices (monostrand or multistrand) that do not
tests of AASHTO “Standard Specifications for Highway meet the relevant PTI or AASHTO bearing stress and,
Bridges,” Division II, Article 10.3.2.3. where applicable, stiffness requirements. Most commer-
cially marketed multibearing surface anchorage devices are
special anchorage devices. As provided in 18.15.1, such
devices can be used only when they have been shown exper-
imentally to be in compliance with the AASHTO require-
ments. This demonstration of compliance will ordinarily be
furnished by the device manufacturer.
CODE COMMENTARY
Special boundary element — Boundary element
required by 21.9.6.2 or 21.9.6.3. 2
Steel fiber-reinforced concrete — Concrete containing Steel fiber-reinforced concrete — In the Code, discontinuous
dispersed randomly oriented steel fibers. steel fiber reinforcement conforming to 3.5.8 is permitted
only in normalweight concrete proportioned, mixed, sampled,
and evaluated in accordance with Chapter 5.
Strength, nominal — Strength of a member or cross Strength, nominal — Strength of a member or cross section
section calculated in accordance with provisions and calculated using standard assumptions and strength equations,
assumptions of the strength design method of this and nominal (specified) values of material strengths and
Code before application of any strength reduction dimensions is referred to as “nominal strength.” The subscript
factors. See 9.3.1. n is used to denote the nominal strengths; nominal axial
load strength Pn , nominal moment strength Mn, and
nominal shear strength Vn. “Design strength” or usable
strength of a member or cross section is the nominal
strength reduced by the strength reduction factor φ.
CODE COMMENTARY
The basic requirement for strength design may be expressed
2 as follows:
φPn ≥ Pu
φMn ≥ Mu
φVn ≥ Vu
Intermediate precast structural wall — A wall Intermediate precast structural wall — The provisions of
complying with all applicable requirements of 21.4 are intended to result in an intermediate precast struc-
Chapters 1 through 18 in addition to 21.4. tural wall having minimum strength and toughness equiva-
lent to that for an ordinary reinforced concrete structural
wall of cast-in-place concrete. A precast concrete wall satis-
fying only the requirements of Chapters 1 through 18 and
not additional requirements of 21.4 or 21.10 is considered to
have ductility and structural integrity less than that for an
intermediate precast structural wall.
CODE COMMENTARY
Special structural wall — A cast-in-place or Special precast structural wall — The provisions of 21.10
precast wall complying with the requirements of are intended to result in a special precast structural wall 2
21.1.3 through 21.1.7, 21.9, and 21.10, as appli- having minimum strength and toughness equivalent to that
cable, in addition to the requirements for ordinary for a special reinforced concrete structural wall of cast-in-
reinforced concrete structural walls. place concrete.
CODE COMMENTARY
Yield strength — Specified minimum yield strength or
2 yield point of reinforcement. Yield strength or yield
point shall be determined in tension according to
applicable ASTM standards as modified by 3.5 of this
Code.
CHAPTER 3 — MATERIALS
CODE COMMENTARY 3
3.1 — Tests of materials R3.1 — Tests of materials
3.1.3 — A complete record of tests of materials and of R3.1.3 — The record of tests of materials and of concrete
concrete shall be retained by the inspector for 2 years should be retained for at least 2 years after completion of
after completion of the project, and made available for the project. Completion of the project is the date at which
inspection during the progress of the Work. the owner accepts the project or when the certificate of
occupancy is issued, whichever date is later. Local legal
requirements may require longer retention of such records.
3.2.1 — Cementitious materials shall conform to the R3.2.1 — Type IS (≥70) is a blended cement under ASTM
relevant specifications as follows: C595 that contains ground-granulated blast-furnace slag as
an interground component in a quantity equal to or
(a) Portland cement: ASTM C150; exceeding 70 percent by weight. This was called Type S or
Type SA cement in versions of ASTM C595 before 2006.
(b) Blended hydraulic cements: ASTM C595
excluding Type IS (≥70), which is not intended as
principal cementing constituents of structural concrete;
3.2.2 — Cementitious materials used in the Work R3.2.2 — Depending on the circumstances, the provision of
shall correspond to those used as the basis for 3.2.2 may require the same type of cementitious materials or
selecting concrete mixture proportions. See 5.2. may require cementitious materials from the same respective
sources. The latter would be the case if the sample standard
deviation3.1 of strength tests used in establishing the required
strength margin was based on cementitious materials from a
particular source. If the sample standard deviation was based
on tests involving cementitious materials obtained from
several sources, the former interpretation would apply.
CODE COMMENTARY
3.3 — Aggregates R3.3 — Aggregates
3.3.1 — Concrete aggregates shall conform to one of R3.3.1 — Aggregates conforming to ASTM specifications are
3 the following specifications: not always economically available and, in some instances,
noncomplying materials have a long history of satisfactory
(a) Normalweight: ASTM C33; performance. Such nonconforming materials are permitted
when acceptable evidence of satisfactory performance is
(b) Lightweight: ASTM C330. provided. Satisfactory performance in the past, however,
Exception: Aggregates that have been shown by test does not guarantee good performance under other conditions
or actual service to produce concrete of adequate and in other localities. Whenever possible, aggregates
strength and durability and approved by the building conforming to the designated specifications should be used.
official.
3.3.2 — Nominal maximum size of coarse aggregate R3.3.2 — The size limitations on aggregates are provided to
shall be not larger than: ensure proper encasement of reinforcement and to minimize
honeycombing. Note that the limitations on maximum size
(a) 1/5 the narrowest dimension between sides of of the aggregate may be waived if, in the judgment of the
forms, nor licensed design professional, the workability and methods
of consolidation of the concrete are such that the concrete
(b) 1/3 the depth of slabs, nor can be placed without honeycombs or voids.
(c) 3/4 the minimum clear spacing between indi-
vidual reinforcing bars or wires, bundles of bars, indi-
vidual tendons, bundled tendons, or ducts.
3.4.1 — Water used in mixing concrete shall conform R3.4.1 — Almost any natural water that is drinkable
to ASTM C1602M. (potable) and has no pronounced taste or odor is satisfactory
as mixing water for making concrete. Excessive impurities
in mixing water may affect not only setting time, concrete
strength, and volume stability (length change), but may also
cause efflorescence or corrosion of reinforcement. Where
possible, water with high concentrations of dissolved solids
should be avoided.
CODE COMMENTARY
3.4.2 — Mixing water for prestressed concrete or for
concrete that will contain aluminum embedments,
including that portion of mixing water contributed in the
form of free moisture on aggregates, shall not contain 3
deleterious amounts of chloride ion. See 4.3.1.
3.5.1 — Reinforcement shall be deformed reinforcement, R3.5.1 — Discontinuous deformed steel fibers are
except that plain reinforcement shall be permitted for permitted only for resisting shear in flexural members (see
spirals or prestressing steel; and reinforcement 11.4.6.3). Fiber-reinforced polymer (FRP) reinforcement is
consisting of headed shear studs, structural steel, not addressed in this Code. ACI Committee 440 has developed
steel pipe, or steel tubing shall be permitted as specified guidelines for the use of FRP reinforcement.3.2, 3.3
in this Code. Discontinuous deformed steel fibers shall
be permitted only for resisting shear under conditions Materials permitted for use as reinforcement are specified.
specified in 11.4.6.3. Other metal elements, such as inserts, anchor bolts, or plain
bars for dowels at isolation or contraction joints, are not
normally considered to be reinforcement under the provisions
of this Code.
3.5.2 — Welding of reinforcing bars shall conform to R3.5.2 — When welding of reinforcing bars is required, the
AWS D1.4. Type and location of welded splices and weldability of the steel and compatible welding procedures
other required welding of reinforcing bars shall be indi- need to be considered. The provisions in AWS D1.4
cated on the design drawings or in the project specifi- Welding Code cover aspects of welding reinforcing bars,
cations. ASTM specifications for bar reinforcement, including criteria to qualify welding procedures.
except for ASTM A706M, shall be supplemented to
require a report of material properties necessary to Weldability of the steel is based on its chemical composition
conform to the requirements in AWS D1.4. or carbon equivalent (CE). The Welding Code establishes
preheat and interpass temperatures for a range of carbon
equivalents and reinforcing bar sizes. Carbon equivalent is
calculated from the chemical composition of the reinforcing
bars. The Welding Code has two expressions for calculating
carbon equivalent. A relatively short expression, considering
only the elements carbon and manganese, is to be used for
bars other than ASTM A706M material. A more comprehen-
sive expression is given for ASTM A706M bars. The CE
formula in the Welding Code for ASTM A706M bars is
identical to the CE formula in ASTM A706M.
CODE COMMENTARY
to the requirements of the Welding Code. Appendix A of the
Welding Code contains a suggested form that shows the
information required for such a specification for each joint
3 welding procedure.
3.5.3.1 — Deformed reinforcing bars shall conform R3.5.3.1 — ASTM A615M covers deformed carbon-steel
to the requirements for deformed bars in one of the reinforcing bars that are currently the most widely used type
following specifications, except as permitted by 3.5.3.3: of steel bar in reinforced concrete construction in the United
States. The specification requires that the bars be marked
(a) Carbon steel: ASTM A615M; with the letter S for type of steel.
(b) Low-alloy steel: ASTM A706M; ASTM A706M covers low-alloy steel deformed bars
(c) Stainless steel: ASTM A955M; intended for applications where controlled tensile properties,
restrictions on chemical composition to enhance weldability,
(d) Rail steel and axle steel: ASTM A996M. Bars or both, are required. The specification requires that the bars
from rail steel shall be Type R. be marked with the letter W for type of steel.
CODE COMMENTARY
Stainless steel bars are used in applications where high
corrosion resistance or controlled magnetic permeability are
required. The physical and mechanical property require-
ments for stainless steel bars under ASTM A955M are the 3
same as those for carbon-steel bars under ASTM A615M.
Rail steel reinforcing bars used with this Code are required
to conform to ASTM A996M including the provisions for
Type R bars, and marked with the letter R for type of steel.
Type R bars are required to meet more restrictive provisions
for bend tests.
3.5.3.2 — Deformed reinforcing bars shall conform to R3.5.3.2 — ASTM A615M includes provisions for
one of the ASTM specifications listed in 3.5.3.1, except Grade 520 bars in sizes No. 19 through 57.
that for bars with fy exceeding 420 MPa, the yield
strength shall be taken as the stress corresponding to a The 0.35 percent strain limit is necessary to ensure that the
strain of 0.35 percent. See 9.4. assumption of an elasto-plastic stress-strain curve in 10.2.4
will not lead to unconservative values of the member strength.
3.5.3.5 — Deformed wire for concrete reinforcement R3.5.3.5 — An upper limit is placed on the size of
shall conform to ASTM A496M, except that wire shall deformed wire because tests show that MD290 wire will
not be smaller than size MD25 or larger than size achieve only approximately 60 percent of the bond strength
MD200 unless as permitted in 3.5.3.7. For wire with fy in tension given by Eq. (12-1).3.5
exceeding 420 MPa, the yield strength shall be taken
as the stress corresponding to a strain of 0.35 percent.
CODE COMMENTARY
3.5.3.6 — Welded plain wire reinforcement shall R3.5.3.6 — Welded plain wire reinforcement is made of
conform to ASTM A185M, except that for wire with fy wire conforming to ASTM A82M, which specifies a
exceeding 420 MPa, the yield strength shall be taken as minimum yield strength of 485 MPa. The Code has
3 the stress corresponding to a strain of 0.35 percent. assigned a yield strength value of 420 MPa, but makes
Spacing of welded intersections shall not exceed 300 mm provision for the use of higher yield strengths provided the
in direction of calculated stress, except for welded wire stress corresponds to a strain of 0.35 percent.
reinforcement used as stirrups in accordance with
12.13.2.
3.5.3.7 — Welded deformed wire reinforcement shall R3.5.3.7 — Welded deformed wire reinforcement should
conform to ASTM A497M, except that for wire with fy be made of wire conforming to ASTM A497M, which
exceeding 420 MPa, the yield strength shall be taken specifies a minimum yield strength of 485 MPa. The Code
as the stress corresponding to a strain of 0.35 percent. has assigned a yield strength value of 420 MPa, but makes
Spacing of welded intersections shall not exceed 400 mm provision for the use of higher yield strengths provided the
in direction of calculated stress, except for welded stress corresponds to a strain of 0.35 percent.
deformed wire reinforcement used as stirrups in accor-
dance with 12.13.2. Deformed wire larger than MD200
is permitted when used in welded wire reinforcement
conforming to ASTM A497M, but shall be treated as
plain wire for development and splice design.
3.5.3.8 — Galvanized reinforcing bars shall conform R3.5.3.8 — Galvanized reinforcing bars (ASTM A767M)
to ASTM A767M. Epoxy-coated reinforcing bars shall and epoxy-coated reinforcing bars (ASTM A775M) were
comply with ASTM A775M or with ASTM A934M. Bars added to the 1983 Code, and epoxy-coated prefabricated
to be galvanized or epoxy-coated shall conform to one reinforcing bars (ASTM A934M) were added to the 1995
of the specifications listed in 3.5.3.1. Code recognizing their usage, especially for conditions
where corrosion resistance of reinforcement is of particular
concern. They have typically been used in parking decks,
bridge structures, and other highly corrosive environments.
3.5.3.10 — Deformed stainless-steel wire and R3.5.3.10 — Stainless steel wire and welded wire are
deformed and plain stainless-steel welded wire for used in applications where high corrosion resistance or
concrete reinforcement shall conform to ASTM controlled magnetic permeability are required. The physical
A1022M, except deformed wire shall not be smaller than and mechanical property requirements for deformed stainless
size MD25 or larger than size MD200, and the yield steel wire and deformed and plain welded wire under
strength for wire with fy exceeding 420 MPa shall be ASTM A1022M are the same as those for deformed wire,
taken as the stress corresponding to a strain of 0.35 deformed welded wire, and plain welded wire under ASTM
percent. Deformed wire larger than MD200 is permitted A496M, A497M, and A185M, respectively.
where used in welded wire reinforcement conforming
to ASTM A1022M, but shall be treated as plain wire for
development and splice design. Spacing of welded
intersections shall not exceed 300 mm for plain welded
wire and 400 mm for deformed welded wire in direction
of calculated stress, except for welded wire reinforce-
ment used as stirrups in accordance with 12.13.2.
3.5.4.1 — Plain bars for spiral reinforcement shall Plain bars and plain wire are permitted only for spiral
conform to the specification listed in 3.5.3.1(a) or (b). reinforcement (either as lateral reinforcement for compression
CODE COMMENTARY
members, for torsion members, or for confining reinforcement
for splices).
3.5.5 — Headed shear stud reinforcement R3.5.5 — The configuration of the studs for headed shear
stud reinforcement differs from the configuration of the
3.5.5.1 — Headed studs and headed stud assem- headed-type shear studs prescribed in Section 7 of AWS
blies shall conform to ASTM A1044M. D1.1 and referenced for use in Appendix D of this Code
(Fig. R3.5.5). Ratios of the head to shank cross-sectional
areas of the AWS D1.1 studs range from about 2.5 to 4. In
contrast, ASTM A1044M requires the area of the head of
headed shear reinforcement studs to be at least 10 times the
area of the shank. Thus, according to 3.5.5.1, the AWS D1.1
headed studs are not suitable for use as headed shear stud
reinforcement. The base rail, where provided, anchors one
end of the studs; ASTM A1044M specifies material width
and thickness of the base rail that are sufficient to provide
the required anchorage without yielding for stud shank diame-
ters of 9.5, 12.7, 15.9, and 19 mm. In ASTM A1044M, the
minimum specified yield strength of headed shear studs is
360 MPa.
3.5.6.1 — Steel for prestressing shall conform to one R3.5.6.1 — Because low-relaxation prestressing steel is
of the following specifications: addressed in a supplement to ASTM A421M, which applies
only when low-relaxation material is specified, the appropriate
(a) Wire: ASTM A421M; ASTM reference is listed as a separate entity.
(b) Low-relaxation wire: ASTM A421M, including
Supplement “Low Relaxation Wire”;
(b) High-strength low-alloy steel: ASTM A242M; Fig. R3.5.5—Configurations of stud heads.
CODE COMMENTARY
(c) High-strength, low-alloy, Colombium-Vanadium
steel: ASTM A572M;
3.5.8 — Steel discontinuous fiber reinforcement for R3.5.8 — Deformations in steel fibers enhance mechanical
concrete shall be deformed and conform to ASTM anchorage with the concrete. The lower and upper limits for
A820M. Steel fibers have a length-to-diameter ratio the fiber length-to-diameter ratio are based on available test
not smaller than 50 and not greater than 100. data.3.6 Because data are not available on the potential for
corrosion problems due to galvanic action, the use of
deformed steel fibers in members reinforced with stainless-
steel bars or galvanized steel bars is not recommended.
3.5.9 — Headed deformed bars shall conform to R3.5.9 — The 2db limitation is due to a lack of test data for
ASTM A970M and obstructions or interruptions of the headed deformed bars that do not meet this requirement.
bar deformations, if any, shall not extend more than Figure R3.5.9 shows a headed bar that has an obstruction of
2db from the bearing face of the head. the deformations that extends less than a distance 2db from
the bearing face of the head and, thus, meets the limitation
expressed in 3.5.9. The figure also illustrates that, because
the diameter of the obstruction is larger than the diameter of
the bar, the net bearing area of the head may be less than the
gross area of the head minus the area of the bar.
CODE COMMENTARY
3.6 — Admixtures R3.6 — Admixtures
3.6.4 — Calcium chloride or admixtures containing R3.6.4 — Admixtures containing any chloride, other than
chloride from sources other than impurities in admix- impurities from admixture ingredients, should not be used
ture ingredients shall not be used in prestressed in prestressed concrete or in concrete with aluminum
concrete, in concrete containing embedded aluminum, embedments. Concentrations of chloride ion may produce
or in concrete cast against stay-in-place galvanized corrosion of embedded aluminum (e.g., conduit), especially
steel forms. See 4.3.1 and 6.3.2. if the aluminum is in contact with embedded steel and the
concrete is in a humid environment. Corrosion of galva-
nized steel sheet and galvanized steel stay-in-place forms
occurs, especially in humid environments or where drying is
inhibited by the thickness of the concrete or coatings or
impermeable coverings. See 4.4.1 for specific limits on
chloride ion concentration in concrete. See 6.3.2 for require-
ments of embedded aluminum.
3.6.5 — Admixtures used in concrete containing expan- R3.6.5 — The use of admixtures in concrete containing ASTM
sive cements conforming to ASTM C845 shall be C845 expansive cements has resulted in reduced levels of
compatible with the cement and produce no deleterious expansion or increased shrinkage values. See ACI 223.3.7
effects.
3.8.1 — Standards of ASTM International referred to in ASTM standards are available from ASTM International.
this Code are listed below with their serial designations,
including year of adoption or revision, and are declared The ASTM standards listed are the latest editions at the time
to be part of this Code as if fully set forth herein: these code provisions were adopted. Because these standards
are revised frequently, generally in minor details only, the
A36/A36M-05 Standard Specification for Carbon user of the Code should check directly with ASTM Inter-
Structural Steel national (www.astm.org) if it is desired to reference the
latest edition. However, such a procedure obligates the user
A53/A53M-07 Standard Specification for Pipe, of the standard to evaluate if any changes in the later edition
Steel, Black and Hot-Dipped, Zinc- are significant in the use of the standard.
Coated, Welded and Seamless
CODE COMMENTARY
A82/A82M-07 Standard Specification for Steel Many of the ASTM standards are combined standards as
Wire, Plain, for Concrete Rein- denoted by the dual designation, such as ASTM A36/
forcement A36M. In 3.8, the complete designation is given because
3 that is the official designation for the standard.
A184/A184M-06 Standard Specification for Welded
Deformed Steel Bar Mats for Standard specifications or other material to be legally
Concrete Reinforcement adopted by reference into a building code should refer to a
specific document. This can be done by simply using the
A185/A185M-07 Standard Specification for Steel complete serial designation since the first part indicates the
Welded Wire Reinforcement, subject and the second part the year of adoption. All stan-
Plain, for Concrete dard documents referenced in this Code are listed in 3.8,
with the title and complete serial designation. In other
A242/A242M-04ε1 Standard Specification for High- sections of the code, the designations do not include the date
Strength Low-Alloy Structural so that all may be kept up-to-date by simply revising 3.8.
Steel
Type R rail-steel bars are considered a mandatory require-
A307-07a Standard Specification for Carbon ment whenever ASTM A996M is referenced in the Code.
Steel Bolts and Studs, 60,000 psi
Tensile Strength
CODE COMMENTARY
A615/A615M-07 Standard Specification for
Deformed and Plain Carbon Steel
Bars for Concrete Reinforcement
3
A706/A706M-06a Standard Specification for Low-
Alloy Steel Deformed and Plain
Bars for Concrete Reinforcement
CODE COMMENTARY
A1044/A1044M-05 Standard Specification for Steel
Stud Assemblies for Shear Rein-
forcement of Concrete
3
C29/C29M-97(2003)Standard Test Method for Bulk
Density (“Unit Weight”) and Voids
in Aggregate
CODE COMMENTARY
C494/C494M-05a Standard Specification for
Chemical Admixtures for Concrete
CODE COMMENTARY
C1609/C1609M-06 Standard Test Method for Flexural
Performance of Fiber-Reinforced
Concrete (Using Beam With
3 Third-Point Loading)
3.8.2 — “Structural Welding Code—Reinforcing Steel R3.8.2 — “Structural Welding Code—Reinforcing Steel
(AWS D1.4/D1.4M:2005)” of the American Welding (AWS D1.4/D1.4M:2005)” is available from the American
Society is declared to be part of this Code as if fully set Welding Society.
forth herein.
3.8.3 — Section 2.3.3, Load Combinations Including R3.8.3 — ASCE/SEI 7-05 is available from ASCE.
Flood Loads, and 2.3.4, Load Combinations Including
Atmospheric Ice Loads, of “Minimum Design Loads for
Buildings and Other Structures” (ASCE/SEI 7-05) is
declared to be part of this code as if fully set forth
herein, for the purpose cited in 9.2.4.
3.8.5 — Articles 9.21.7.2 and 9.21.7.3 of Division I and R3.8.5 — The 2002 17th Edition of the AASHTO “Stan-
Article 10.3.2.3 of Division II of AASHTO “Standard dard Specification for Highway Bridges” is available from
Specification for Highway Bridges” (AASHTO 17th AASHTO.
Edition, 2002) are declared to be a part of this Code as
if fully set forth herein, for the purpose cited in 18.15.1.
3.8.6 — “Qualification of Post-Installed Mechanical R3.8.6 — Parallel to development of the 2005 Code provisions
Anchors in Concrete (ACI 355.2-07)” is declared to be for anchoring to concrete, ACI 355 developed a test method
part of this Code as if fully set forth herein, for the to define the level of performance required for post-installed
purpose cited in Appendix D. anchors. This test method, ACI 355.2, contains require-
ments for the testing and evaluation of post-installed anchors
for both cracked and uncracked concrete applications.
3.8.7 — “Structural Welding Code—Steel (AWS D1.1/ R3.8.7 — “Structural Welding Code—Steel (AWS D1.1/
D1.1M:2006)” of the American Welding Society is D1.1M:2006)” is available from the American Welding
declared to be part of this Code as if fully set forth Society.
herein.
4.1.1 —The value of fc′ shall be the greatest of the R4.1.1 — Maximum water-cementitious material ratios
values required by (a) 1.1.1, (b) for durability in (w/cm) of 0.40 to 0.50 that may be required for concretes
Chapter 4, and (c) for structural strength requirements exposed to freezing and thawing, sulfate soils or waters, or
and shall apply for mixture proportioning in 5.3 and for for corrosion protection of reinforcement will typically be
evaluation and acceptance of concrete in 5.6. equivalent to requiring an fc′ of 35 to 28 MPa, respectively.
Concrete mixtures shall be proportioned to comply Generally, the required average compressive strengths, fcr′ ,
with the maximum water-cementitious material ratio will be 3.5 to 5 MPa higher than the specified compressive
(w/cm) and other requirements based on the exposure strength, fc′ . Because it is difficult to accurately determine
class assigned to the concrete structural member. All the w/cm of concrete, the fc′ specified should be reasonably
cementitious materials specified in 3.2.1 and the consistent with the w/cm required for durability. Selection
combinations of these materials shall be included in of an fc′ that is consistent with the maximum permitted
calculating the w/cm of the concrete mixture. w/cm for durability will help ensure that the maximum w/cm
is not exceeded in the field. For example, a maximum w/cm
of 0.45 and fc′ of 21 MPa should not be specified for the
same concrete mixture. Because the usual emphasis during
inspection is on concrete compressive strength, test results
substantially higher than the specified compressive strength
may lead to a lack of concern for quality and could result in
production and delivery of concrete that exceeds the
maximum w/cm.
4.1.2 — The maximum w /cm limits in Chapter 4 do not R4.1.2 — Maximum w/cm is not specified for lightweight
apply to lightweight concrete. concrete because of the uncertainty in determining the
amount of mixing water that is absorbed by lightweight
aggregates before concrete sets. This makes the calculation
of the w/cm uncertain. The use of a minimum specified
compressive strength, fc′ , will ensure the use of a high-
quality cement paste. For normalweight concrete, the use of
both minimum strength and maximum w/cm provide
additional assurance that the paste is of high quality.
4.2 — Exposure categories and classes R4.2 — Exposure categories and classes
CODE COMMENTARY
finishes. These items are beyond the scope of the Code and
should be covered specifically in the project specifications.
Concrete ingredients and proportions are to be selected to
meet the minimum requirements stated in the Code and the
additional requirements of contract documents.
4
4.2.1 — The licensed design professional shall assign R4.2.1 — The Code addresses four exposure categories that
exposure classes based on the severity of the antici- affect the requirements for concrete to ensure adequate
pated exposure of structural concrete members for durability:
each exposure category according to Table 4.2.1.
Exposure Category F applies to exterior concrete that is
exposed to moisture and cycles of freezing and thawing,
with or without deicing chemicals.
TABLE 4.2.1 — EXPOSURE CATEGORIES AND
CLASSES
Exposure Category S applies to concrete in contact with
Category Severity Class Condition soil or water containing deleterious amounts of water-
Not F0 Concrete not exposed to freezing- soluble sulfate ions as defined in 4.2.1.
applicable and-thawing cycles
Concrete exposed to freezing-and-
Moderate F1 thawing cycles and occasional Exposure Category P applies to concrete in contact with
exposure to moisture water requiring low permeability.
F
Freezing Concrete exposed to freezing-and-
and thawing Severe F2 thawing cycles and in continuous
contact with moisture Exposure Category C applies to reinforced and prestressed
Concrete exposed to freezing-and- concrete exposed to conditions that require additional
Very thawing and in continuous contact protection against corrosion of reinforcement.
F3
severe with moisture and exposed to deicing
chemicals
Water-soluble Severity of exposure within each category is defined by
sulfate (SO4) in Dissolved classes with increasing numerical values representing
soil, percent by sulfate (SO4) in
weight water, ppm increasingly severe exposure conditions. A classification of
Not
S0 SO4 < 0.10 SO4 < 150
“0” is assigned when the exposure severity has negligible
applicable effect or does not apply to the structural member.
S
Sulfate 150 ≤ SO4 <1500
Moderate S1 0.10 ≤ SO4 < 0.20
Seawater
1500 ≤ SO4 ≤
Exposure Category F is subdivided into four exposure
Severe S2 0.20 ≤ SO4 ≤ 2.00 10,000 classes: Exposure Class F0 is assigned to concrete that will
Very
S3 SO4 > 2.00 SO4 > 10,000
not be exposed to cycles of freezing and thawing. Exposure
severe Class F1 is assigned to concrete exposed to cycles of
P Not P0 In contact with water where low freezing and thawing and that will be occasionally exposed
Requiring applicable permeability is not required
low In contact with water where low
to moisture before freezing. Examples of Class F1 are exterior
permeability Required P1
permeability is required. walls, beams, girders, and slabs not in direct contact with
Not Concrete dry or protected from
C0 moisture
soil. Exposure Class F2 is assigned to concrete exposed to
applicable cycles of freezing and thawing that is in continuous contact
C
Moderate C1 Concrete exposed to moisture but with moisture before freezing. An example is an exterior
Corrosion not to external sources of chlorides
protection
Concrete exposed to moisture and
water tank or vertical members in contact with soil.
of reinforce- Exposure Classes F1 and F2 are conditions where exposure
an external source of chlorides from
ment
Severe C2 deicing chemicals, salt, brackish to deicing salt is not anticipated. Exposure Class F3 is
water, seawater, or spray from these
sources assigned to concrete exposed to cycles of freezing and
thawing, in continuous contact with moisture, and where
exposure to deicing chemicals is anticipated. Examples are
horizontal members in parking structures.
CODE COMMENTARY
from Exposure Class S1 to S3 based on the more critical
value of measured water-soluble sulfate concentration in
soil or the concentration of dissolved sulfate in water. Sea
water exposure is classified as Exposure Class S1.
4.3 — Requirements for concrete mixtures R4.3 — Requirements for concrete mixtures
4.3.1 — Based on the exposure classes assigned from R4.3.1 — Table 4.3.1 gives the requirements for concrete on
Table 4.2.1, concrete mixtures shall comply with the the basis of the assigned exposure classes. When a structural
most restrictive requirements according to Table 4.3.1. concrete member is assigned more than one exposure class,
the most restrictive requirements are applicable. For
example, a prestressed concrete member assigned to Exposure
Class C2 and Exposure Class F3 would require concrete to
comply with a maximum w/cm of 0.40 and minimum fc′ of
35 MPa, respectively. In this case, the requirement for
corrosion protection is more restrictive than the requirement
for resistance to freezing and thawing.
CODE COMMENTARY
TABLE 4.3.1 — REQUIREMENTS FOR CONCRETE the principal consideration is its tricalcium aluminate (C3A)
BY EXPOSURE CLASS content. For Exposure Class S1 (moderate exposure), Type II
Expo- Min. cement is limited to a maximum C3A content of 8.0 percent
sure Max. fc′ , under ASTM C150. The blended cements under ASTM
Class w/cm* MPa Additional minimum requirements
C595 with the MS designation are appropriate for use in
4 Limits on
cementi- Exposure Class S1. The appropriate types under ASTM
tious C595 are IP(MS) and IS(<70)(MS) and under C1157 is
Air content materials
Type MS. For Exposure Class S2 (severe exposure), Type V
F0 N/A 17 N/A N/A
cement with a maximum C3A content of 5 percent is speci-
F1 0.45 31 Table 4.4.1 N/A
fied. Blended cements Types IP (HS) and IS (<70) (HS)
F2 0.45 31 Table 4.4.1 N/A
under ASTM C595 and Type HS under ASTM C1157 can
Table
F3 0.45 31 Table 4.4.1 also be used. In certain areas, the C3A content of other
4.4.2
Cementitious materials†—types available types such as Type III or Type I may be less than 8
Calcium
ASTM ASTM ASTM chloride or 5 percent and are usable in moderate or severe sulfate
C150 C595 C1157 admixture exposures. Note that sulfate-resisting cement will not
No Type No Type No Type No increase resistance to some chemically aggressive solutions,
S0 N/A 17
restriction restriction restriction restriction
for example, sulfuric acid. The project specifications should
IP(MS),
No cover all special cases.
S1 0.50 28 II‡ IS (<70) MS
restriction
(MS)
IP (HS) The use of fly ash (ASTM C618, Class F), natural pozzolans
Not
S2 0.45 31 V§ IS (<70) HS
permitted
(HS) (ASTM C618, Class N), silica fume (ASTM C1240), or
IP (HS) + ground-granulated blast-furnace slag (ASTM C989) also has
pozzolan or been shown to improve the sulfate resistance of concrete.4.1-4.3
V+ slag|| or IS HS +
Not
S3 0.45 31 pozzolan or (<70) pozzolan ASTM C1012 can be used to evaluate the sulfate resistance of
|| permitted
slag (HS) + or slag|| mixtures using combinations of cementitious materials as
pozzolan or
slag|| determined in 4.5.1. For Exposure Class S3, the alternative in
ACI 318-05 allowing use of Type V plus pozzolan, based on
P0 N/A 17 None records of successful service, instead of meeting the testing
P1 0.50 28 None requirements of 4.5.1, still exists and has been expanded to
Maximum water-soluble consider the use of slag and the blended cements.
chloride ion (Cl–)
content in concrete,
percent by weight of Table 4.3.1 lists seawater under Exposure Class S1 (moderate
cement# exposure), even though it generally contains more than
Reinforced Prestressed 1500 ppm SO4. Portland cement with higher C3A content
concrete concrete Related provisions
improves binding of chlorides present in seawater and the
C0 N/A 17 1.00 0.06
None Code permits other types of portland cement with C3A up to
C1 N/A 17 0.30 0.06
10 percent if the maximum w/cm is reduced to 0.40.
C2 0.40 35 0.15 0.06 7.7.6, 18.16**
*For lightweight concrete, see 4.1.2.
†
Alternative combinations of cementitious materials of those listed in Table 4.3.1 In addition to the proper selection of cementitious materials,
shall be permitted when tested for sulfate resistance and meeting the criteria in
4.5.1. other requirements for durable concrete exposed to water-
‡
For seawater exposure, other types of portland cements with tricalcium alumi- soluble sulfate are essential, such as low w/cm, strength,
nate (C3A) contents up to 10 percent are permitted is the w/cm does not
exceed 0.40.
§
adequate air entrainment, adequate consolidation, uniformity,
Other available types of cement such as Type III or Type I are permitted in
Exposure Classes S1 or S2 if the C3A contents are less than 8 or 5 percent, adequate cover of reinforcement, and sufficient moist curing
respectively. to develop the potential properties of the concrete.
||
The amount of the specific source of the pozzolan or slag to be used shall not
be less than the amount that has been determined by service record to improve
sulfate resistance when used in concrete containing Type V cement. Alterna-
tively, the amount of the specific source of the pozzolan or slag to be used shall Exposure Class P1: The Code includes an Exposure Class
not be less than the amount tested in accordance with ASTM C1012 and
meeting the criteria in 4.5.1. P1 for concrete that needs to have a low permeability when
#
Water-soluble chloride ion content that is contributed from the ingredients in direct contact with water and where the other exposure
including water, aggregates, cementitious materials, and admixtures shall be
determined on the concrete mixture by ASTM C1218M at age between 28 and conditions defined in Table 4.2.1 do not apply. The primary
42 days.
**
Requirements of 7.7.6 shall be satisfied. See 18.16 for unbonded tendons. means to obtain low permeability is to use a low w/cm. Low
permeability can be also achieved by optimizing the cemen-
titious materials used in the concrete mixture. One standard
method that provides a performance-based indicator of low
permeability of concrete is ASTM C1202, which is more reli-
able in laboratory evaluations than for field-based acceptance.
CODE COMMENTARY
Exposure Class C2: For reinforced and prestressed
concrete in Exposure Class C2, the maximum w/cm,
minimum specified compressive strength, and minimum
cover are the basic requirements to be considered. Condi-
tions in structures where chlorides may be applied should be
evaluated, such as in parking structures where chlorides 4
may be tracked in by vehicles, or in structures near seawater.
Epoxy- or zinc-coated bars or cover greater than the
minimum required in 7.7 may be desirable. Use of slag
meeting ASTM C989 or fly ash meeting ASTM C618 and
increased levels of specified compressive strength provide
increased protection. Use of silica fume meeting ASTM
C1240 with an appropriate high-range water reducer,
ASTM C494M, Types F and G, or ASTM C1017M can also
provide additional protection.4.4 The use of ASTM C12024.5
to test concrete mixtures proposed for use will provide
additional information on the performance of the mixtures.
Exposure Classes C0, C1, and C2: For Exposure Classes C0,
C1, and C2, the chloride ion limits apply. For reinforced
concrete, the permitted maximum amount of water-soluble
chloride ions incorporated into the concrete, measured by
ASTM C1218M at ages between 28 and 42 days, depend on
the degree of exposure to an anticipated external source of
moisture and chlorides. For prestressed concrete, the same
limit of 0.06 percent chloride ion by weight of cement
applies regardless of exposure.
CODE COMMENTARY
Table R4.3.1 — Chloride limits for new construction
(adapted from Table 3.1 of ACI 222R4.7)
Chloride limit, percent by mass
Test method
4.4.1 — Normalweight and lightweight concrete subject R4.4.1 — A table of required air contents for concrete to
to Exposure Classes F1, F2, or F3 shall be air-entrained resist damage from cycles of freezing and thawing is
with air content indicated in Table 4.4.1. Tolerance on included in the Code, based on guidance provided for
air content as delivered shall be ±1.5 percent. For fc′ proportioning concrete mixtures in ACI 211.1.4.9 Target
greater than 35 MPa, reduction of air content indicated values are provided for Exposure Class F1 (moderate) and
in Table 4.4.1 by 1.0 percent shall be permitted. both Exposure Classes F2 and F3 (severe) exposures
depending on the exposure to moisture or deicing salts.
Entrained air will not protect concrete containing coarse
aggregates that undergo disruptive volume changes when
TABLE 4.4.1 — TOTAL AIR CONTENT FOR frozen in a saturated condition.
CONCRETE EXPOSED TO CYCLES OF FREEZING
AND THAWING Section 4.4.1 permits 1 percent lower air content for
Air content, percent concrete with fc′ greater than 35 MPa. Such high-strength
Nominal maximum Exposure Classes concretes will have a lower w/cm and porosity and, there-
aggregate size, mm* Exposure Class F1 F2 and F3
fore, improved resistance to cycles of freezing and thawing.
9.5 6 7.5
12.5 5.5 7
19.0 5 6
25.0 4.5 6
37.5 4.5 5.5
50† 4 5
75† 3.5 4.5
*See ASTM C33 for tolerance on oversize for various nominal maximum size
designations.
†
Air contents apply to total mixture. When testing concretes, however, aggre-
gate particles larger than 40 mm are removed by sieving and air content is
measured on the sieved fraction (tolerance on air content as delivered applies
to this value). Air content of total mixture is computed from value measured
on the sieved fraction passing the 40 mm sieve in accordance with ASTM C231.
CODE COMMENTARY
4.4.2 —The quantity of pozzolans, including fly ash and R4.4.2 — Table 4.4.2 establishes limitations on the amount
silica fume, and slag in concrete subject to Exposure of fly ash, other pozzolans, silica fume, and slag that can be
Class F3, shall not exceed the limits in Table 4.4.2. included in concrete exposed to deicing chemicals (Exposure
Class F3) based on research studies.4.10,4.11
TABLE 4.4.2 — REQUIREMENTS FOR CONCRETE 4
SUBJECT TO EXPOSURE CLASS F3
Maximum percent of
total cementitious
Cementitious materials materials by weight*
Fly ash or other pozzolans conforming to
25
ASTM C618
Slag conforming to ASTM C989 50
Silica fume conforming to ASTM C1240 10
Total of fly ash or other pozzolans, slag, and
50†
silica fume
Total of fly ash or other pozzolans and
35†
silica fume
*The
total cementitious material also includes ASTM C150, C595, C845, and
C1157 cement.
The maximum percentages above shall include:
(a) Fly ash or other pozzolans in Type IP, blended cement, ASTM C595, or
ASTM C1157;
(b) Slag used in the manufacture of an IS blended cement, ASTM C595, or
ASTM C1157;
(c) Silica fume, ASTM C1240, present in a blended cement.
†
Fly ash or other pozzolans and silica fume shall constitute no more than 25
and 10 percent, respectively, of the total weight of the cementitious materials.
4.5.1 — Alternative combinations of cementitious R4.5.1 — In the 2008 version of the Code, ASTM C1012 is
materials to those listed in Table 4.3.1 shall be permitted to be used to evaluate the sulfate resistance of
permitted when tested for sulfate resistance and concrete mixtures using alternative combinations of cemen-
meeting the criteria in Table 4.5.1. titious materials to those listed in Table 4.3.1 for all classes
of sulfate exposure. More detailed guidance on qualification
of such mixtures using ASTM C1012 is given in ACI
TABLE 4.5.1 — REQUIREMENTS FOR 201.2R.4.6 The expansion criteria in Table 4.5.1, for testing
ESTABLISHING SUITABILITY OF CEMENTITIOUS according to ASTM C1012, are the same as those in ASTM
MATERIALS COMBINATIONS EXPOSED TO C595 for moderate sulfate resistance (Optional Designation
WATER-SOLUBLE SULFATE MS) in Exposure Class S1 and for high sulfate resistance
Maximum expansion when tested (Optional Designation HS) in Exposure Class S2, and the
using ASTM C1012
Exposure same as in ASTM C1157 for Type MS in Exposure Class S1
Class At 6 months At 12 months At 18 months
and Type HS in Exposure Class S2.
S1 0.10 percent
S2 0.05 percent 0.10 percent*
S3 0.10 percent
*
The 12-month expansion limit applies only when the measured expansion
exceeds the 6-month maximum expansion limit.
CODE COMMENTARY
5.1 — General R5.1 — General
5.1.1 — Concrete shall be proportioned to provide an R5.1.1 — The basic premises governing the designation and
average compressive strength, fcr′ , as prescribed in evaluation of concrete strength are presented. It is empha-
5.3.2 and shall satisfy the durability criteria of Chapter 4. sized that the average compressive strength of concrete
Concrete shall be produced to minimize the frequency produced should always exceed the specified value of fc′
of strength tests below fc′ , as prescribed in 5.6.3.3. used in the structural design calculations. This is based on
For concrete designed and constructed in accordance probabilistic concepts, and is intended to ensure that
with the Code, fc′ shall not be less than 17 MPa. adequate concrete strength will be developed in the structure.
The durability requirements prescribed in Chapter 4 are to
be satisfied in addition to attaining the average concrete
strength in accordance with 5.3.2.
5.1.4 — Where design criteria in 8.6.1, 12.2.4(d), and R5.1.4 — Equations throughout the code that contain the
22.5.6.1 provide for use of a splitting tensile strength f c′ term have been modified, as necessary, for use with
value of concrete, laboratory tests shall be made in lightweight concrete. Two alternative modification proce-
accordance with ASTM C330 to establish a value of dures are provided. One alternative is based on laboratory
′ corresponding to fc′.
fct tests to determine the relationship between average splitting
tensile strength fct and specified compressive strength fc′ for
the lightweight concrete. For a lightweight aggregate from a
given source, it is intended that appropriate values of fct be
obtained in advance of design.
5.1.5 — Splitting tensile strength tests shall not be R5.1.5 — Tests for splitting tensile strength of concrete (as
used as a basis for field acceptance of concrete. required by 5.1.4) are not intended for control of, or accep-
tance of, the strength of concrete in the field. Indirect
control will be maintained through the normal compressive
strength test requirements provided by 5.6.
CODE COMMENTARY
5.1.6 — Steel fiber-reinforced concrete shall conform
to ASTM C1116. The minimum fc′ for steel fiber-
reinforced concrete shall conform to 5.1.1.
5.2.1 — Proportions of materials for concrete shall be R5.2.1 — The selected water-cementitious material ratio
established to: should be low enough, or in the case of lightweight concrete
the compressive strength, high enough to satisfy both the
(a) Provide workability and consistency to permit strength criteria (see 5.3 or 5.4) and the requirements for
concrete to be worked readily into forms and around applicable exposure categories of Chapter 4. The code does
reinforcement under conditions of placement to be not include provisions for especially severe exposure
employed, without segregation or excessive bleeding; conditions, such as acids or high temperatures, and is not
concerned with aesthetic considerations such as surface
(b) Meet requirements for applicable exposure finishes. These items are beyond the scope of the Code and
categories of Chapter 4; should be covered specifically in the project specifications.
(c) Conform to strength test requirements of 5.6. Concrete ingredients and proportions are to be selected to
meet the minimum requirements stated in the Code and the
5.2.2 — Where different materials are to be used for additional requirements of the contract documents.
different portions of proposed Work, each combination
shall be evaluated.
5.2.3 — Concrete proportions shall be established in R5.2.3 — The Code emphasizes the use of field experience
accordance with 5.3 or, alternatively, 5.4, and shall or laboratory trial mixtures (see 5.3) as the preferred method
meet applicable requirements of Chapter 4. for selecting concrete mixture proportions.
5.3 — Proportioning on the basis of field R5.3 — Proportioning on the basis of field
experience or trial mixtures, or both experience or trial mixtures, or both
CODE COMMENTARY
5.3.1 — Sample standard deviation R5.3.1 — Sample standard deviation
5.3.1.1 — Where a concrete production facility has When a concrete production facility has a suitable record of
strength test records not more than 12 months old, a 30 consecutive tests of similar materials and conditions
sample standard deviation, ss , shall be established. expected, the sample standard deviation, ss, is calculated
Test records from which ss is calculated: from those results in accordance with the following
formula:
5 (a) Shall represent materials, quality control proce-
dures, and conditions similar to those expected and 2 1/2
changes in materials and proportions within the test Σ ( xi – x )
ss = ------------------------
records shall not have been more restricted than those (n – 1)
for proposed Work;
where
(b) Shall represent concrete produced to meet a ss = sample standard deviation, MPa
specified compressive strength or strengths within 7 MPa xi = individual strength tests as defined in 5.6.2.4
of fc′ ; x = average of n strength test results
n = number of consecutive strength tests
(c) Shall consist of at least 30 consecutive tests or two
groups of consecutive tests totaling at least 30 tests as The sample standard deviation is used to determine the
defined in 5.6.2.4, except as provided in 5.3.1.2. average strength required in 5.3.2.1.
5.3.1.2 — Where a concrete production facility does If two test records are used to obtain at least 30 tests, the
not have strength test records meeting requirements sample standard deviation used shall be the statistical
of 5.3.1.1(c), but does have test records not more than average of the values calculated from each test record in
12 months old based on 15 to 29 consecutive tests, a accordance with the following formula:
sample standard deviation ss shall be established as
the product of the calculated sample standard deviation 2 2 1/2
and modification factor of Table 5.3.1.2. To be accept- ( n 1 – 1 ) ( s s1 ) + ( n 2 – 1 ) ( s s2 )
ss = ---------------------------------------------------------------------------
-
able, test records shall meet requirements (a) and (b) ( n1 + n2 – 2 )
of 5.3.1.1, and represent only a single record of
consecutive tests that span a period of not less than
where
45 calendar days.
ss = statistical average standard deviation where two
test records are used to estimate the sample standard
deviation
TABLE 5.3.1.2 —MODIFICATION FACTOR FOR ss1, ss2= sample standard deviations calculated from two
SAMPLE STANDARD DEVIATION WHEN LESS test records, 1 and 2, respectively
THAN 30 TESTS ARE AVAILABLE n1, n2 = number of tests in each test record, respectively
Modification factor for sample
No. of tests* standard deviation† If less than 30 tests, but at least 15 tests are available, the
Less than 15 Use Table 5.3.2.2 calculated sample standard deviation is increased by the
15 1.16 factor given in Table 5.3.1.2. This procedure results in a
20 1.08 more conservative (increased) required average strength.
25 1.03 The factors in Table 5.3.1.2 are based on the sampling
30 or more 1.00 distribution of the sample standard deviation and provide
*
Interpolate for intermediate numbers of tests.
†Modified sample standard deviation, s , to be
s used to determined required protection (equivalent to that from a record of 30 tests)
average strength, fcr′ , from 5.3.2.1 against the possibility that the smaller sample underestimates
the true or universe population standard deviation.
CODE COMMENTARY
made with the same general types of ingredients under no
more restrictive conditions of control over material quality
and production methods than on the proposed Work, and if
its specified strength does not deviate more than 7 MPa
from the fc′ required [see 5.3.1.1(b)]. A change in the type
of concrete or a major increase in the strength level may
increase the sample standard deviation. Such a situation
might occur with a change in type of aggregate (i.e., from 5
natural aggregate to lightweight aggregate or vice versa) or
a change from non-air-entrained concrete to air-entrained
concrete. Also, there may be an increase in sample standard
deviation when the average strength level is raised by a
significant amount, although the increment of increase in
sample standard deviation should be somewhat less than
directly proportional to the strength increase. When there is
reasonable doubt, any estimated sample standard deviation
used to calculate the required average strength should
always be on the conservative (high) side.
5.3.2.1 — Required average compressive strength R5.3.2.1 — Once the sample standard deviation has been
fcr′ used as the basis for selection of concrete propor- determined, the required average compressive strength, fcr′ ,
tions shall be determined from Table 5.3.2.1 using the is obtained from the larger value computed from Eq. (5-1)
sample standard deviation, ss , calculated in accor- and (5-2) for fc′ of 35 MPa or less, or the larger value
dance with 5.3.1.1 or 5.3.1.2. computed from Eq. (5-1) and (5-3) for fc′ over 35 MPa.
Equation (5-1) is based on a probability of 1-in-100 that the
TABLE 5.3.2.1 — REQUIRED AVERAGE average of three consecutive tests may be below the specified
COMPRESSIVE STRENGTH WHEN DATA ARE compressive strength fc′ . Equation (5-2) is based on a
AVAILABLE TO ESTABLISH A SAMPLE similar probability that an individual test may be more than
STANDARD DEVIATION 3.5 MPa below the specified compressive strength fc′ .
Equation (5-3) is based on the same 1-in-100 probability
Specified compressive Required average compressive
strength, MPa strength, MPa that an individual test may be less than 0.90fc′ . These equations
Use the larger value computed assume that the sample standard deviation used is equal to
from Eq. (5-1) and (5-2) the population value appropriate for an infinite or very large
fc′ ≤ 35 fcr′ = fc′ + 1.34ss (5-1)
number of tests. For this reason, use of sample standard
fcr′ = fc′ + 2.33ss – 3.5 (5-2)
deviations estimated from records of 100 or more tests is
Use the larger value computed
from Eq. (5-1) and (5-3) desirable. When 30 tests are available, the probability of
fc′ > 35 fcr′ = fc′ + 1.34ss (5-1) failure will likely be somewhat greater than 1-in-100. The
fcr′ = 0.90fc′ + 2.33ss (5-3)
additional refinements required to achieve the 1-in-100
probability are not considered necessary because of the
CODE COMMENTARY
uncertainty inherent in assuming that conditions operating
when the test record was accumulated will be similar to
conditions when the concrete will be produced.
Documentation that proposed concrete proportions Once the required average compressive strength fcr′ is
will produce an average compressive strength equal to known, the next step is to select mixture proportions that
or greater than required average compressive strength will produce an average strength at least as great as the
fcr′ (see 5.3.2) shall consist of a field strength test required average strength, and also meet requirements for
record, several strength test records, or trial mixtures. applicable exposure categories of Chapter 4. The documen-
tation may consist of a strength test record, several strength
5.3.3.1 — When test records in accordance with test records, or suitable laboratory or field trial mixtures.
5.3.1.1 or 5.3.1.2 are used to demonstrate that Generally, if a test record is used, it will be the same one
proposed concrete proportions will produce fcr′ (see that was used for computation of the standard deviation.
5.3.2), such records shall represent materials and However, if this test record shows either lower or higher
conditions similar to those expected. Changes in average compressive strength than the required average
materials, conditions, and proportions within the test compressive strength, different proportions may be necessary
records shall not have been more restricted than those or desirable. In such instances, the average from a record of
for proposed Work. For the purpose of documenting as few as 10 tests may be used, or the proportions may be
average strength potential, test records consisting of established by interpolation between the strengths and
less than 30 but not less than 10 consecutive tests are proportions of two such records of consecutive tests. All test
acceptable provided test records encompass a period records for establishing proportions necessary to produce the
of time not less than 45 days. Required concrete average compressive strength are to meet the requirements of
proportions shall be permitted to be established by 5.3.3.1 for “similar materials and conditions.”
interpolation between the strengths and proportions of
two or more test records, each of which meets other For strengths over 35 MPa where the average compressive
requirements of this section. strength documentation is based on laboratory trial
mixtures, it may be appropriate to increase fcr′ calculated in
Table 5.3.2.2 to allow for a reduction in strength from
laboratory trials to actual concrete production.
5.3.3.2 — When an acceptable record of field test R5.3.3.2 — This section of the Code was modified in ACI
results is not available, concrete proportions established 318-08 to clarify the requirements for making trial batches.
from trial mixtures meeting the following requirements
shall be permitted: (b) For concrete made with more than one type of cemen-
titious material, the concrete supplier must establish not
CODE COMMENTARY
(a) Materials shall be those for proposed Work; only the water-cementitious material ratio but also the
relative proportions of cementitious materials and admix-
(b) Trial mixtures with a range of proportions that will tures, if any, that will produce the required average
produce a range of compressive strengths encom- compressive strength and satisfy the durability requirements
passing fcr′ and meet the durability requirements of of Chapter 4. This will require multiple trial batches with
Chapter 4; different mixture proportions. The exact number of
(c) Trial mixtures shall have slumps within the range batches will depend on the number of cementitious
materials and the range of their relative proportions. 5
specified for the proposed Work; for air-entrained
concrete, air content shall be within the tolerance (d) Starting with the 2008 Code, 5.6.2.4 permits two
specified for the proposed Work; cylinder sizes for preparing test specimens for field
(d) For each trial mixture, at least two 150 by 300 mm or acceptance testing.
three 100 by 200 mm cylinders shall be made and (e) The compressive strength test results may be analyzed
cured in accordance with ASTM C192M. Cylinders shall graphically or using regression models to determine the
be tested at 28 days or at test age designated for fc′ ; water-cementitious material ratio and the relative
(e) The compressive strength results, at designated proportions of cementitious materials, if other materials
test age, from the trial mixtures shall be used to in addition to portland cement are used, that will produce
establish the composition of the concrete mixture concrete satisfying the required average compressive
proposed for the Work. The proposed concrete strength fcr′ .
mixture shall achieve an average compressive
strength as required in 5.3.2 and satisfy the appli-
cable durability criteria of Chapter 4.
CODE COMMENTARY
(b) Fifteen to 29 test results are available and
average of test results exceeds that required by
5.3.2.1 using a sample standard deviation calculated
in accordance with 5.3.1.2; and
Once the mixture proportions have been selected and the job
started, the criteria for evaluation and acceptance of the
concrete can be obtained from 5.6.
5.6.1 — Concrete shall be tested in accordance with R5.6.1 — Laboratory and field technicians can establish
the requirements of 5.6.2 through 5.6.5. Qualified field qualifications by becoming certified through certification
testing technicians shall perform tests on fresh programs. Field technicians in charge of sampling concrete;
concrete at the job site, prepare specimens required testing for slump, unit weight, yield, air content, and
for curing under field conditions, prepare specimens temperature; and making and curing test specimens should
required for testing in the laboratory, and record the be certified in accordance with the requirements of ACI
temperature of the fresh concrete when preparing Concrete Field Testing Technician—Grade 1 Certification
specimens for strength tests. Qualified laboratory Program, or the requirements of ASTM C1077,5.3 or an
technicians shall perform all required laboratory tests. equivalent program. Concrete testing laboratory personnel
should be certified in accordance with the requirements of ACI
Concrete Laboratory Testing Technician, Concrete Strength
Testing Technician, or the requirements of ASTM C1077.
5.6.2.1 — Samples for strength tests of each class R5.6.2.1 — The following three criteria establish the
of concrete placed each day shall be taken not less required minimum sampling frequency for each class of
than once a day, nor less than once for each 110 m3 of concrete:
concrete, nor less than once for each 460 m2 of
surface area for slabs or walls. (a) Once each day a given class is placed, nor less than
(b) Once for each 110 m3 of each class placed each day,
nor less than
CODE COMMENTARY
5.6.2.2 — On a given project, if total volume of R5.6.2.2 — Samples for strength tests are to be taken on
concrete is such that frequency of testing required by a strictly random basis if they are to measure properly the
5.6.2.1 would provide less than five strength tests for a acceptability of the concrete. To be representative, the
given class of concrete, tests shall be made from at choice of times of sampling, or the batches of concrete to be
least five randomly selected batches or from each sampled, are to be made on the basis of chance alone, within
batch if fewer than five batches are used. the period of placement. Batches should not be sampled on
the basis of appearance, convenience, or other possibly
biased criteria, because the statistical analyses will lose their 5
validity. Not more than one test (as defined in 5.6.2.4)
should be taken from a single batch, and water may not be
added to the concrete after the sample is taken.
5.6.2.4 — A strength test shall be the average of the R5.6.2.4 — More than the minimum number of specimens
strengths of at least two 150 by 300 mm cylinders or at may be desirable to allow for discarding an outlying indi-
least three 100 by 200 mm cylinders made from the vidual cylinder strength in accordance with ACI 214R.5.5
same sample of concrete and tested at 28 days or at When individual cylinder strengths are discarded in accor-
test age designated for determination of fc′ . dance with ACI 214R, a strength test is valid provided at
least two individual 150 by 300 mm cylinder strengths or at
least three 100 by 200 mm cylinders are averaged. All indi-
vidual cylinder strengths that are not discarded in accor-
dance with ACI 214R are to be used to calculate the average
strength. The size and number of specimens representing a
strength test should remain constant for each class of concrete.
5.6.3.2 — Cylinders for strength tests shall be R5.6.3.2 — The cylinder size should be agreed upon by
molded and standard-cured in accordance with ASTM the owner, licensed design professional, and testing agency
C31M and tested in accordance with ASTM C39M. before construction.
Cylinders shall be 100 by 200 mm or 150 by 300 mm.
5.6.3.3 — Strength level of an individual class of R5.6.3.3 — A single set of criteria is given for accept-
concrete shall be considered satisfactory if both of the ability of strength and is applicable to all concrete used in
following requirements are met: structures designed in accordance with the Code, regardless
of design method used. The concrete strength is considered
(a) Every arithmetic average of any three consecutive to be satisfactory as long as averages of any three consecutive
strength tests (see 5.6.2.4) equals or exceeds fc′ ; strength tests remain above the specified fc′ and no individual
CODE COMMENTARY
(b) No strength test (see 5.6.2.4) falls below fc′ by strength test falls below the specified fc′ by more than 3.5 MPa
more than 500 psi when fc′ is 35 MPa or less; or by if fc′ is 35 MPa or less, or falls below fc′ by more than 10
more than 0.10fc′ when fc′ is more than 35 MPa. percent if fc′ is over 35 MPa. Evaluation and acceptance of
the concrete can be judged immediately as test results are
received during the course of the Work. Strength tests failing
to meet these criteria will occur occasionally (probably about
once in 100 tests) even though concrete strength and
5 uniformity are satisfactory. Allowance should be made for
such statistically expected variations in deciding whether
the strength level being produced is adequate.
5.6.3.4 — If either of the requirements of 5.6.3.3 is R5.6.3.4 — When concrete fails to meet either of the
not met, steps shall be taken to increase the average strength requirements of 5.6.3.3, steps should be taken to
of subsequent strength test results. Requirements of increase the average of the concrete test results. If sufficient
5.6.5 shall be observed if requirement of 5.6.3.3(b) is concrete has been produced to accumulate at least 15 tests,
not met. these should be used to establish a new target average
strength as described in 5.3.
CODE COMMENTARY
(NVLAP), Cement and Concrete Reference Laboratory
(CCRL), or their equivalent.
5.6.4.1 — If required by the building official, results R5.6.4.1 — Strength tests of cylinders cured under field
of strength tests of cylinders cured under field conditions conditions may be required to check the adequacy of curing
shall be provided. and protection of concrete in the structure. 5
5.6.4.4 — Procedures for protecting and curing R5.6.4.4 — Positive guidance is provided in the Code
concrete shall be improved when strength of field- concerning the interpretation of tests of field-cured cylinders.
cured cylinders at test age designated for determina- Research has shown that cylinders protected and cured to
tion of fc′ is less than 85 percent of that of companion simulate good field practice should test not less than about
laboratory-cured cylinders. The 85 percent limitation 85 percent of standard laboratory moist-cured cylinders.
shall not apply if field-cured strength exceeds fc′ by This percentage has been set as a rational basis for judging
more than 3.5 MPa. the adequacy of field curing. The comparison is made
between the actual measured strengths of companion job-
cured and laboratory-cured cylinders, not between job-
cured cylinders and the specified value of fc′ . However,
results for the job-cured cylinders are considered satisfac-
tory if the job-cured cylinders exceed the specified fc′ by
more than 3.5 MPa, even though they fail to reach 85 percent
of the strength of companion laboratory-cured cylinders.
5.6.5 — Investigation of low-strength test results R5.6.5 — Investigation of low-strength test results
5.6.5.1 — If any strength test (see 5.6.2.4) of Instructions are provided concerning the procedure to be
laboratory-cured cylinders falls below fc′ by more than followed when strength tests have failed to meet the speci-
the values given in 5.6.3.3(b) or if tests of field-cured fied acceptance criteria. For obvious reasons, these instruc-
cylinders indicate deficiencies in protection and curing tions cannot be dogmatic. The building official should apply
(see 5.6.4.4), steps shall be taken to ensure that load- judgment as to the significance of low test results and
carrying capacity of the structure is not jeopardized. whether they indicate need for concern. If further investigation
is deemed necessary, such investigation may include
5.6.5.2 — If the likelihood of low-strength concrete is nondestructive tests or, in extreme cases, strength tests of
confirmed and calculations indicate that load-carrying cores taken from the structure.
capacity is significantly reduced, tests of cores drilled
from the area in question in accordance with ASTM Nondestructive tests of the concrete in place, such as by
C42M shall be permitted. In such cases, three cores probe penetration, impact hammer, ultrasonic pulse velocity
shall be taken for each strength test that falls below or pullout may be useful in determining whether or not a
the values given in 5.6.3.3(b). portion of the structure actually contains low-strength
concrete. Such tests are of value primarily for comparisons
5.6.5.3 — Cores shall be obtained, moisture condi- within the same job rather than as quantitative measures of
tioned by storage in watertight bags or containers, strength. For cores, if required, conservatively safe acceptance
transported to the laboratory, and tested in accor- criteria are provided that should ensure structural adequacy
dance with ASTM C42M. Cores shall be tested no for virtually any type of construction.5.7-5.10 Lower strength
earlier than 48 hours and not later than 7 days after may, of course, be tolerated under many circumstances, but
coring unless approved by the licensed design profes- this again becomes a matter of judgment on the part of the
sional. The specifier of tests referenced in ASTM building official and licensed design professional. When the
C42M shall be the licensed design professional. core tests performed in accordance with 5.6.5.4 fail to
CODE COMMENTARY
5.6.5.4 — Concrete in an area represented by core provide assurance of structural adequacy, it may be prac-
tests shall be considered structurally adequate if the tical, particularly in the case of floor or roof systems, for the
average of three cores is equal to at least 85 percent building official to require a load test (Chapter 20). Short of
of fc′ and if no single core is less than 75 percent of fc′ . load tests, if time and conditions permit, an effort may be
Additional testing of cores extracted from locations made to improve the strength of the concrete in place by
represented by erratic core strength results shall be supplemental wet curing. Effectiveness of such a treatment
permitted. should be verified by further strength evaluation using
5 procedures previously discussed.
5.6.5.5 — If criteria of 5.6.5.4 are not met and if the
structural adequacy remains in doubt, the responsible The use of a water-cooled bit results in a core with a moisture
authority shall be permitted to order a strength evaluation gradient between the exterior surface and the interior. This
in accordance with Chapter 20 for the questionable gradient lowers the apparent compressive strength of the
portion of the structure, or take other appropriate action. core.5.11 The restriction on the commencement of core
testing provides a minimum time for the moisture gradient
to dissipate. The maximum time between coring and testing
is intended to ensure timely testing of cores when strength
of concrete is in question. Research5.11 has also shown that
procedures for soaking or drying cores that were required
before ACI 318-02 affect measured compressive strength
and result in conditions that are not representative of
structures that are dry or wet in service. Thus, to provide
reproducible moisture conditions that are representative of
in-place conditions, a common moisture conditioning
procedure that permits dissipation of moisture gradients is
prescribed for cores. ASTM C42M permits the specifier of
tests to modify the default duration of moisture conditioning
before testing.
5.6.6.1 — Acceptance of steel fiber-reinforced R5.6.6.1 — The performance criteria are based on results
concrete used in beams in accordance with 11.4.6.1(f) from flexural tests5.12 conducted on steel fiber-reinforced
shall be determined by testing in accordance with concretes with fiber types and contents similar to those used
ASTM C1609. In addition, strength testing shall be in in the tests of beams that served as the basis for 11.4.6.1(f).
accordance with 5.6.1.
CODE COMMENTARY
5.6.6.2 — Steel fiber-reinforced concrete shall be R5.6.6.2(b),(c) — The term “residual strength” is defined
considered acceptable for shear resistance if condi- in ASTM C1609.
tions (a), (b), and (c) are satisfied:
5.7 — Preparation of equipment and place R5.7 — Preparation of equipment and place
of deposit of deposit
5.7.1 — Preparation before concrete placement shall Recommendations for mixing, handling and transporting,
include the following: and placing concrete are given in detail in ACI 304R.5.13
(This presents methods and procedures for control, handling
(a) All equipment for mixing and transporting and storage of materials, measurement, batching tolerances,
concrete shall be clean; mixing, methods of placing, transporting, and forms.)
(b) All debris and ice shall be removed from spaces Attention is directed to the need for using clean equipment
to be occupied by concrete; and for cleaning forms and reinforcement thoroughly before
(c) Forms shall be properly coated; beginning to deposit concrete. In particular, sawdust, nails,
wood pieces, and other debris that may collect inside the forms
(d) Masonry filler units that will be in contact with should be removed. Reinforcement should be thoroughly
concrete shall be well drenched; cleaned of ice, dirt, loose rust, mill scale, or other coatings.
Water should be removed from the forms.
(e) Reinforcement shall be thoroughly clean of ice or
other deleterious coatings;
CODE COMMENTARY
5.8 — Mixing R5.8 — Mixing
5.8.1 — All concrete shall be mixed until there is a Concrete of uniform and satisfactory quality requires the
uniform distribution of materials and shall be materials to be thoroughly mixed until uniform in appear-
discharged completely before mixer is recharged. ance and all ingredients are distributed. Samples taken from
different portions of a batch should have essentially the
5.8.2 — Ready-mixed concrete shall be mixed and same unit weight, air content, slump, and coarse aggregate
5 delivered in accordance with requirements of ASTM content. Test methods for uniformity of mixing are given in
C94M or C685M. ASTM C94M. The necessary time of mixing will depend on
many factors including batch size, stiffness of the batch,
5.8.3 — Job-mixed concrete shall be mixed in accor- size and grading of the aggregate, and the efficiency of the
dance with (a) through (e): mixer. Excessively long mixing times should be avoided to
guard against grinding of the aggregates.
(a) Mixing shall be done in a batch mixer of
approved type;
5.9.1 — Concrete shall be conveyed from mixer to Each step in the handling and transporting of concrete needs
place of final deposit by methods that will prevent to be controlled to maintain uniformity within a batch and
separation or loss of materials. from batch to batch. It is essential to avoid segregation of
the coarse aggregate from the mortar or of water from the
5.9.2 — Conveying equipment shall be capable of other ingredients.
providing a supply of concrete at site of placement
without separation of ingredients and without interrup- The Code requires the equipment for handling and trans-
tions sufficient to permit loss of plasticity between porting concrete to be capable of supplying concrete to the
successive increments. place of deposit continuously and reliably under all conditions
and for all methods of placement. The provisions of 5.9
apply to all placement methods, including pumps, belt
conveyors, pneumatic systems, wheelbarrows, buggies,
crane buckets, and tremies.
CODE COMMENTARY
much as 50 percent. Hence, equipment made of aluminum
or aluminum alloys should not be used for pump lines,
tremies, or chutes other than short chutes such as those used
to convey concrete from a truck mixer.
5.10.1 — Concrete shall be deposited as nearly as Rehandling concrete can cause segregation of the materials. 5
practical in its final position to avoid segregation due to Hence, the Code cautions against this practice. Retempering
rehandling or flowing. of partially set concrete with the addition of water should
not be permitted unless authorized. This does not preclude
5.10.2 — Concreting shall be carried on at such a rate the practice (recognized in ASTM C94M) of adding water
that concrete is at all times plastic and flows readily to mixed concrete to bring it up to the specified slump range
into spaces between reinforcement. so long as prescribed limits on the maximum mixing time
and w/cm are not violated.
5.10.3 — Concrete that has partially hardened or been
contaminated by foreign materials shall not be deposited Section 5.10.4 of the 1971 Code contained a requirement
in the structure. that “where conditions make consolidation difficult or
where reinforcement is congested, batches of mortar
5.10.4 — Retempered concrete or concrete that has containing the same proportions of cement, sand, and water
been remixed after initial set shall not be used unless as used in the concrete, shall first be deposited in the forms
approved by the licensed design professional. to a depth of at least 1 in. [25 mm].” That requirement was
deleted from the 1977 Code since the conditions for which it
5.10.5 — After concreting is started, it shall be carried was applicable could not be defined precisely enough to justify
on as a continuous operation until placing of a panel or its inclusion as a code requirement. The practice, however,
section, as defined by its boundaries or predetermined has merit and should be incorporated in job specifications
joints, is completed except as permitted or prohibited where appropriate, with the specific enforcement the
by 6.4. responsibility of the job inspector. The use of mortar batches
aids in preventing honeycomb and poor bonding of the
5.10.6 — Top surfaces of vertically formed lifts shall be concrete with the reinforcement. The mortar should be placed
generally level. immediately before depositing the concrete and should be
plastic (neither stiff nor fluid) when the concrete is placed.
5.10.7 — When construction joints are required, joints
shall be made in accordance with 6.4. Recommendations for consolidation of concrete are given in
detail in ACI 309R.5.15 (This presents current information
5.10.8 — All concrete shall be thoroughly consolidated on the mechanism of consolidation and gives recommenda-
by suitable means during placement and shall be thor- tions on equipment characteristics and procedures for
oughly worked around reinforcement and embedded various classes of concrete.)
fixtures and into corners of forms.
5.11.1 — Concrete (other than high-early-strength) Recommendations for curing concrete are given in detail in
shall be maintained above 10 °C and in a moist ACI 308R.5.16 (This presents basic principles of proper
condition for at least the first 7 days after placement, curing and describes the various methods, procedures, and
except when cured in accordance with 5.11.3. materials for curing of concrete.)
CODE COMMENTARY
5.11.3 — Accelerated curing R5.11.3 — Accelerated curing
5.11.3.1 — Curing by high-pressure steam, steam at The provisions of this section apply whenever an accelerated
atmospheric pressure, heat and moisture, or other curing method is used, whether for precast or cast-in-place
accepted processes, shall be permitted to accelerate elements. The compressive strength of steam-cured concrete
strength gain and reduce time of curing. is not as high as that of similar concrete continuously cured
under moist conditions at moderate temperatures. Also, the
5 5.11.3.2 — Accelerated curing shall provide a modulus of elasticity Ec of steam-cured specimens may
compressive strength of the concrete at the load stage vary from that of specimens moist-cured at normal
considered at least equal to required design strength temperatures. When steam curing is used, it is advisable to
at that load stage. base the concrete mixture proportions on steam-cured test
cylinders.
5.11.3.3 — Curing process shall be such as to
produce concrete with a durability at least equivalent Accelerated curing procedures require careful attention to
to the curing method of 5.11.1 or 5.11.2. obtain uniform and satisfactory results. Preventing moisture
loss during the curing is essential.
5.11.4 — When required by the licensed design R5.11.4 — In addition to requiring a minimum curing
professional, supplementary strength tests in accor- temperature and time for normal- and high-early-strength
dance with 5.6.4 shall be performed to assure that concrete, the Code provides a specific criterion in 5.6.4 for
curing is satisfactory. judging the adequacy of field curing. At the test age for
which the compressive strength is specified (usually 28 days),
field-cured cylinders should produce strength not less than
85 percent of that of the standard, laboratory-cured cylinders.
For a reasonably valid comparison to be made, field-cured
cylinders and companion laboratory-cured cylinders should
come from the same sample. Field-cured cylinders should
be cured under conditions identical to those of the structure.
If the structure is protected from the elements, the cylinder
should be protected.
5.12.1 — Adequate equipment shall be provided for Recommendations for cold weather concreting are given
heating concrete materials and protecting concrete in detail in ACI 306R.5.17 (This presents requirements and
during freezing or near-freezing weather. methods for producing satisfactory concrete during cold
weather.)
5.12.2 — All concrete materials and all reinforcement,
forms, fillers, and ground with which concrete is to
come in contact shall be free from frost.
CODE COMMENTARY
5.13 — Hot weather requirements R5.13 — Hot weather requirements
During hot weather, proper attention shall be given to Recommendations for hot weather concreting are given in
ingredients, production methods, handling, placing, detail in ACI 305R.5.18 (This defines the hot weather factors
protection, and curing to prevent excessive concrete that affect concrete properties and construction practices
temperatures or water evaporation that could impair and recommends measures to eliminate or minimize the
required strength or serviceability of the member or undesirable effects.)
structure. 5
6.1.1 — Forms shall result in a final structure that Only minimum performance requirements for formwork,
conforms to shapes, lines, and dimensions of the necessary to provide for public health and safety, are
members as required by the design drawings and prescribed in Chapter 6. Formwork for concrete, including
specifications. proper design, construction, and removal, demands sound 6
judgment and planning to achieve adequate forms that are
6.1.2 — Forms shall be substantial and sufficiently both economical and safe. Detailed information on form-
tight to prevent leakage of mortar. work for concrete is given in: “Guide to Formwork for
Concrete,” reported by Committee 347.6.1 (This provides
6.1.3 — Forms shall be properly braced or tied recommendations for design, construction, and materials for
together to maintain position and shape. formwork, forms for special structures, and formwork for
special methods of construction. Directed primarily to
6.1.4 — Forms and their supports shall be designed contractors, the suggested criteria will aid in preparing
so as not to damage previously placed structure. project specifications for the contractors.)
6.1.5 — Design of formwork shall include consider- Formwork for Concrete,6.2 reported by ACI Committee 347.
ation of the following factors: (This is a how-to-do-it handbook for contractors, engineers,
and architects following the guidelines established in ACI
(a) Rate and method of placing concrete; 347. Planning, building, and using formwork are discussed,
including tables, diagrams, and formulas for form design
(b) Construction loads, including vertical, horizontal, loads.)
and impact loads;
6.2 — Removal of forms, shores, and R6.2 — Removal of forms, shores, and
reshoring reshoring
6.2.1 — Removal of forms In determining the time for removal of forms, consideration
should be given to the construction loads and to the possibilities
Forms shall be removed in such a manner as not to of deflections.6.3 The construction loads are frequently at
impair safety and serviceability of the structure. least as great as the specified live loads. At early ages, a
Concrete exposed by form removal shall have sufficient structure may be adequate to support the applied loads but
strength not to be damaged by removal operation. may deflect sufficiently to cause permanent damage.
6.2.2 — Removal of shores and reshoring Evaluation of concrete strength during construction may be
demonstrated by field-cured test cylinders or other procedures
The provisions of 6.2.2.1 through 6.2.2.3 shall apply to approved by the building official such as:
slabs and beams except where cast on the ground.
(a) Tests of cast-in-place cylinders in accordance with
6.2.2.1 — Before starting construction, the ASTM C873.6.4 (This method is limited to use in slabs
contractor shall develop a procedure and schedule for where the depth of concrete is from 120 to 300 mm);
removal of shores and installation of reshores and for
calculating the loads transferred to the structure during (b) Penetration resistance in accordance with ASTM
the process. C803M6.5;
CODE COMMENTARY
(a) The structural analysis and concrete strength (c) Pullout strength in accordance with ASTM C9006.6;
data used in planning and implementing form
removal and shoring shall be furnished by the (d) Maturity index measurements and correlation in
contractor to the building official when so requested; accordance with ASTM C1074.6.7
(b) No construction loads shall be supported on, nor Procedures (b), (c), and (d) require sufficient data, using job
any shoring removed from, any part of the structure materials, to demonstrate correlation of measurements on
under construction except when that portion of the the structure with compressive strength of molded cylinders
structure in combination with remaining forming and or drilled cores.
6 shoring system has sufficient strength to support
Where the structure is adequately supported on shores, the
safely its weight and loads placed thereon;
side forms of beams, girders, columns, walls, and similar
(c) Sufficient strength shall be demonstrated by vertical forms may generally be removed after 12 hours of
structural analysis considering proposed loads, cumulative curing time, provided the side forms support no
strength of forming and shoring system, and loads other than the lateral pressure of the plastic concrete.
concrete strength data. Concrete strength data shall Cumulative curing time represents the sum of time intervals,
be based on tests of field-cured cylinders or, when not necessarily consecutive, during which the temperature
approved by the building official, on other proce- of the air surrounding the concrete is above 10 °C. The
dures to evaluate concrete strength. 12-hour cumulative curing time is based on regular cements
and ordinary conditions; the use of special cements or
6.2.2.2 — No construction loads exceeding the unusual conditions may require adjustment of the given
combination of superimposed dead load plus specified limits. For example, concrete made with Type II or V
live load shall be supported on any unshored portion (ASTM C150) or ASTM C595 cements, concrete containing
of the structure under construction, unless analysis retarding admixtures, and concrete to which ice was added
indicates adequate strength to support such additional during mixing (to lower the temperature of fresh concrete)
loads. may not have sufficient strength in 12 hours and should be
investigated before removal of formwork.
6.2.2.3 — Form supports for prestressed concrete
members shall not be removed until sufficient The removal of formwork for multistory construction
prestressing has been applied to enable prestressed should be a part of a planned procedure considering the
members to carry their dead load and anticipated temporary support of the entire structure as well as that of
construction loads. each individual member. Such a procedure should be
worked out prior to construction and should be based on a
structural analysis taking into account the following items,
as a minimum:
CODE COMMENTARY
6.3 — Embedments in concrete R6.3 — Embedments in concrete
6.3.1 — Embedments of any material not harmful to R6.3.1 — Any embedments (e.g, conduits, pipes, and
concrete and within limitations of 6.3 shall be sleeves) not harmful to concrete can be placed in the
permitted in concrete with approval of the licensed concrete, but the Work should be done in such a manner that
design professional, provided they are not considered the structure will not be endangered. Empirical rules are
to replace structurally the displaced concrete, except given in 6.3 for safe installations under common conditions;
as provided in 6.3.6. for other than common conditions, special designs should
be made. Many general building codes have adopted ANSI/
ASME piping codes B 31.1 for power piping6.8 and B 31.3 6
for chemical and petroleum piping.6.9 The licensed design
professional should be sure that the appropriate piping
codes are used in the design and testing of the system. The
contractor should not be permitted to install conduits, pipes,
ducts, or sleeves that are not shown on the design drawings
or not approved by the licensed design professional.
6.3.2 — Any aluminum embedments in structural R6.3.2 — The Code prohibits the use of aluminum in
concrete shall be coated or covered to prevent structural concrete unless it is effectively coated or covered.
aluminum-concrete reaction or electrolytic action Aluminum reacts with concrete and, in the presence of
between aluminum and steel. chloride ions, may also react electrolytically with steel,
causing cracking and/or spalling of the concrete. Aluminum
electrical conduits present a special problem since stray electric
current accelerates the adverse reaction. Provision 3.6.3
prohibits calcium chloride or any admixture containing
chloride from being used in concrete with aluminum
embedments.
CODE COMMENTARY
6.3.5.3 — They shall not impair significantly the
strength of the construction.
6.3.7 — Pipes and fittings shall be designed to resist R6.3.7 — The 1983 Code limited the maximum pressure in
effects of the material, pressure, and temperature to embedded pipe to 1.4 MPa, which was considered too
which they will be subjected. restrictive. Nevertheless, the effects of such pressures and
the expansion of embedded pipe should be considered in the
design of the concrete member.
6.4.1 — Surface of concrete construction joints shall For the integrity of the structure, it is important that all
be cleaned and laitance removed. construction joints be defined in construction documents
and constructed as required. Any deviations should be
approved by the licensed design professional.
CODE COMMENTARY
6.4.2 — Immediately before new concrete is placed, R6.4.2 — The requirements of the 1977 Code for the use of
all construction joints shall be wetted and standing neat cement on vertical joints have been removed, since it is
water removed. rarely practical and can be detrimental where deep forms
and steel congestion prevent proper access. Often wet
blasting and other procedures are more appropriate.
Because the Code sets only minimum standards, the
licensed design professional may have to specify additional
procedures if conditions warrant. The degree to which
mortar batches are needed at the start of concrete placement
depend on concrete proportions, congestion of steel, 6
vibrator access, and other factors.
6.4.3 — Construction joints shall be so made and R6.4.3 — Construction joints should be located where they
located as not to impair the strength of the structure. will cause the least weakness in the structure. When shear
Provision shall be made for transfer of shear and other due to gravity load is not significant, as is usually the case in
forces through construction joints. See 11.6.9. the middle of the span of flexural members, a simple
vertical joint may be adequate. Lateral force design may
require special design treatment of construction joints.
Shear keys, intermittent shear keys, diagonal dowels, or the
shear transfer method of 11.7 may be used whenever a force
transfer is required.
6.4.6 — Beams, girders, or slabs supported by R6.4.6 — Delay in placing concrete in members supported
columns or walls shall not be cast or erected until by columns and walls is necessary to prevent cracking at the
concrete in the vertical support members is no longer interface of the slab and supporting member caused by
plastic. bleeding and settlement of plastic concrete in the supporting
member.
6.4.7 — Beams, girders, haunches, drop panels, shear R6.4.7 — Separate placement of slabs and beams,
caps, and capitals shall be placed monolithically as haunches, and similar elements is permitted when shown on
part of a slab system, unless otherwise shown in the drawings and where provision has been made to transfer
design drawings or specifications. forces as required in 6.4.3.
CODE COMMENTARY
7.1 — Standard hooks R7.1 — Standard hooks
The term “standard hook” as used in this Code shall Recommended methods and standards for preparing design
mean one of the following: drawings, typical details, and drawings for the fabrication
and placing of reinforcing steel in reinforced concrete struc-
7.1.1 — 180-degree bend plus 4db extension, but not tures are given in the ACI Detailing Manual, reported by
less than 65 mm at free end of bar. ACI Committee 315.7.1
7
7.1.2 — 90-degree bend plus 12db extension at free All provisions in the Code relating to bar, wire, or strand
end of bar. diameter (and area) are based on the nominal dimensions of
the reinforcement as given in the appropriate ASTM specifi-
cation. Nominal dimensions are equivalent to those of a
circular area having the same weight per foot as the ASTM
designated bar, wire, or strand sizes. Cross-sectional area of
reinforcement is based on nominal dimensions.
7.1.3 — For stirrup and tie hooks R7.1.3 — Standard stirrup and tie hooks are limited to No. 25
bars and smaller, and the 90-degree hook with 6db extension
(a) No. 16 bar and smaller, 90-degree bend plus 6db is further limited to No. 16 bars and smaller, in both cases as
extension at free end of bar; or the result of research showing that larger bar sizes with
90-degree hooks and 6db extensions tend to pop out under
(b) No. 19, No. 22, and No. 25 bar, 90-degree bend high load.
plus 12db extension at free end of bar; or
7.2.1 — Diameter of bend measured on the inside of Standard bends in reinforcing bars are described in terms
the bar, other than for stirrups and ties in sizes No. 10 of the inside diameter of bend because this is easier to
through No. 16, shall not be less than the values in measure than the radius of bend. The primary factors
Table 7.2. affecting the minimum bend diameter are feasibility of
bending without breakage and avoidance of crushing the
concrete inside the bend.
7.2.2 — Inside diameter of bend for stirrups and ties R7.2.2 — The minimum 4db bend for the bar sizes
shall not be less than 4db for No. 16 bar and smaller. commonly used for stirrups and ties is based on accepted
For bars larger than No. 16, diameter of bend shall be industry practice in the United States. Use of a stirrup bar
in accordance with Table 7.2. size not greater than No. 16 for either the 90-degree or
135-degree standard stirrup hook will permit multiple
bending on standard stirrup bending equipment.
7.2.3 — Inside diameter of bend in welded wire R7.2.3 — Welded wire reinforcement can be used for stirrups
reinforcement for stirrups and ties shall not be less and ties. The wire at welded intersections does not have the
than 4db for deformed wire larger than MD40 and 2db same uniform ductility and bendability as in areas that were
for all other wires. Bends with inside diameter of less not heated. These effects of the welding temperature are
than 8db shall not be less than 4db from nearest usually dissipated in a distance of approximately four wire
welded intersection. diameters. Minimum bend diameters permitted are in most
cases the same as those required in the ASTM bend tests for
wire material (ASTM A82M and A496M).
ACI 318 Building Code and Commentary
88 CHAPTER 7
CODE COMMENTARY
TABLE 7.2 — MINIMUM DIAMETERS OF BEND
Bar size Minimum diameter
No. 10 through No. 25 6db
No. 29, No. 32, and No. 36 8db
No. 43 and No. 57 10db
7.3.1 — All reinforcement shall be bent cold, unless R7.3.1 — For unusual bends with inside diameters less than
otherwise permitted by the licensed design professional. ASTM bend test requirements, special fabrication may be
7 required.
7.3.2 — Reinforcement partially embedded in R7.3.2 — Construction conditions may make it necessary to
concrete shall not be field bent, except as shown on bend bars that have been embedded in concrete. Such field
the design drawings or permitted by the licensed bending should not be done without authorization of the
design professional. licensed design professional. Contract documents should
specify whether the bars will be permitted to be bent cold or
if heating should be used. Bends should be gradual and
should be straightened as required.
Tests7.2,7.3 have shown that A615M Grade 280 and Grade 420
reinforcing bars can be cold bent and straightened up to
90 degrees at or near the minimum diameter specified in
7.2. If cracking or breakage is encountered, heating to a
maximum temperature of 820 °C may avoid this condition
for the remainder of the bars. Bars that fracture during bending
or straightening can be spliced outside the bend region.
7.4.1—At the time concrete is placed, reinforcement Specific limits on rust are based on tests,7.4 plus a review
shall be free from mud, oil, or other nonmetallic coatings of earlier tests and recommendations. Reference 7.4
that decrease bond. Epoxy-coating of steel reinforce- provides guidance with regard to the effects of rust and
ment in accordance with standards referenced in mill scale on bond characteristics of deformed reinforcing
3.5.3.8 and 3.5.3.9 shall be permitted. bars. Research has shown that a normal amount of rust
increases bond. Normal rough handling generally removes
7.4.2 — Except for prestressing steel, steel reinforce- rust that is loose enough to injure the bond between the
ment with rust, mill scale, or a combination of both concrete and reinforcement.
shall be considered satisfactory, provided the minimum
dimensions (including height of deformations) and
weight of a hand-wire-brushed test specimen comply
with applicable ASTM specifications referenced in 3.5.
CODE COMMENTARY
7.4.3 — Prestressing steel shall be clean and free of R7.4.3 — Guidance for evaluating the degree of rusting on
oil, dirt, scale, pitting and excessive rust. A light strand is given in Reference 7.5.
coating of rust shall be permitted.
7.5.1 — Reinforcement, including tendons, and post- R7.5.1 — Reinforcement, including tendons, and post-
tensioning ducts shall be accurately placed and tensioning ducts should be adequately supported in the
adequately supported before concrete is placed, and forms to prevent displacement by concrete placement or
shall be secured against displacement within tolerances workers. Beam stirrups should be supported on the bottom
permitted in 7.5.2. form of the beam by positive supports such as continuous
longitudinal beam bolsters. If only the longitudinal beam 7
bottom reinforcement is supported, construction traffic can
dislodge the stirrups as well as any prestressing tendons tied
to the stirrups.
7.5.2 — Unless otherwise specified by the licensed R7.5.2 — Generally accepted practice, as reflected in ACI
design professional, reinforcement, including tendons, 117,7.6 has established tolerances on total depth (formwork
and post-tensioning ducts shall be placed within the or finish) and fabrication of truss bent reinforcing bars and
tolerances in 7.5.2.1 and 7.5.2.2. closed ties, stirrups, and spirals. The licensed design profes-
sional should specify more restrictive tolerances than those
permitted by the Code when necessary to minimize the
accumulation of tolerances resulting in excessive reduction
in effective depth or cover.
7.5.2.1 — Tolerances for d and for concrete cover in R7.5.2.1 — The Code permits a reinforcement placement
flexural members, walls, and compression members tolerance on effective depth d, which is directly related to the
shall be as follows: flexural and shear strength of the member. Because reinforcing
steel is placed with respect to edges of members and form-
Tolerance on specified work surfaces, d is not always conveniently measured in the
Tolerance on d concrete cover
field. Placement tolerances for cover are also provided. For
d ≤ 200 mm ±10 mm –10 mm
guidance on including field tolerances in project specifications,
d > 200 mm ±13 mm –13 mm
see ACI 117.7.6
except that tolerance for the clear distance to formed
soffits shall be minus 6 mm. In addition, tolerance for
cover shall also not exceed minus 1/3 the concrete
cover specified in the design drawings and project
specifications.
CODE COMMENTARY
the discontinuous ends of other members. The toler-
ance for concrete cover of 7.5.2.1 shall also apply at
discontinuous ends of members.
7.6 — Spacing limits for reinforcement R7.6 — Spacing limits for reinforcement
7.6.1 — The minimum clear spacing between parallel Although the minimum bar spacings are unchanged in this
bars in a layer shall be db , but not less than 25 mm. Code, the development lengths given in Chapter 12 became
See also 3.3.2. a function of the bar spacings since the 1989 Code. As a
result, it may be desirable to use larger than minimum bar
7.6.2 — Where parallel reinforcement is placed in two spacings in some cases. The minimum limits were origi-
or more layers, bars in the upper layers shall be placed nally established to permit concrete to flow readily into
directly above bars in the bottom layer with clear spaces between bars and between bars and forms without
distance between layers not less than 25 mm. honeycomb, and to ensure against concentration of bars on a
line that may cause shear or shrinkage cracking. Use of
7.6.3 — In spirally reinforced or tied reinforced nominal bar diameter to define minimum spacing permits a
compression members, clear distance between longi- uniform criterion for all bar sizes.
tudinal bars shall be not less than 1.5db nor less than
40 mm. See also 3.3.2.
7.6.6.1 — Groups of parallel reinforcing bars Bond research7.8 showed that bar cutoffs within bundles
bundled in contact to act as a unit shall be limited to should be staggered. Bundled bars should be tied, wired, or
four in any one bundle. otherwise fastened together to ensure remaining in position
whether vertical or horizontal.
7.6.6.2 — Bundled bars shall be enclosed within A limitation that bars larger than No. 36 not be bundled in
stirrups or ties. beams or girders is a practical limit for application to building
size members. (The “Standard Specifications for Highway
7.6.6.3 — Bars larger than No. 36 shall not be Bridges”7.9 permits two-bar bundles for No. 43 and No. 57
bundled in beams. bars in bridge girders.) Conformance to the crack control
requirements of 10.6 will effectively preclude bundling of
CODE COMMENTARY
7.6.6.4 — Individual bars within a bundle terminated bars larger than No. 36 as tensile reinforcement. The Code
within the span of flexural members shall terminate at phrasing “bundled in contact to act as a unit,” is intended to
different points with at least 40db stagger. preclude bundling more than two bars in the same plane.
Typical bundle shapes are triangular, square, or L-shaped
7.6.6.5 — Where spacing limitations or concrete patterns for three- or four-bar bundles. As a practical caution,
cover requirements are based on bar diameter, db , a bundles more than one bar deep in the plane of bending
unit of bundled bars shall be treated as a single bar of should not be hooked or bent as a unit. Where end hooks are
a diameter derived from the equivalent total area. required, it is preferable to stagger the individual bar hooks
within a bundle.
7.6.7.2 — Bundling of post-tensioning ducts shall be R7.6.7.2 — When ducts for prestressing steel in a beam are
permitted if shown that concrete can be satisfactorily arranged closely together vertically, provision should be
placed and if provision is made to prevent the made to prevent the prestressing steel from breaking through
prestressing steel, when tensioned, from breaking the duct when tensioned. Horizontal disposition of ducts
through the duct. should allow proper placement of concrete. A clear spacing
of one and one-third times the size of the coarse aggregate,
but not less than 25 mm, has proven satisfactory. Where
concentration of tendons or ducts tends to create a weakened
plane in the concrete cover, reinforcement should be provided
to control cracking.
7.7 — Concrete protection for reinforcement R7.7 — Concrete protection for reinforcement
CODE COMMENTARY
Beams, columns: Alternative methods of protecting the reinforcement from
Primary reinforcement, ties, stirrups, weather may be provided if they are equivalent to the
spirals ...............................................................40 additional concrete cover required by the Code. When
Shells, folded plate members: approved by the building official under the provisions of 1.4,
No. 19 bar and larger .......................................20 reinforcement with alternative protection from the weather
No. 16 bar, MW200 or MD200 wire, and smaller ..13 may have concrete cover not less than the cover required for
reinforcement not exposed to weather.
7.7.2 — Cast-in-place concrete (prestressed)
The development length given in Chapter 12 is now a function
Unless a greater concrete cover is required by 7.7.6 or of the bar cover. As a result, it may be desirable to use larger
7.7.8, specified cover for prestressed and nonpre- than minimum cover in some cases.
7 stressed reinforcement, ducts, and end fittings shall
not be less than the following:
Concrete
cover, mm
(a) Concrete cast against and
permanently exposed to earth...............................75
7.7.3 — Precast concrete (manufactured under R7.7.3 — Precast concrete (manufactured under plant
plant control conditions) control conditions)
Unless a greater cover is required by 7.7.6 or 7.7.8, The lesser cover thicknesses for precast construction reflect
specified cover for prestressed and nonprestressed the greater convenience of control for proportioning, placing,
reinforcement, ducts, and end fittings shall not be less and curing inherent in precasting. The term “manufactured
than the following: under plant control conditions” does not specifically imply
that precast members should be manufactured in a plant.
Concrete Structural elements precast at the job site will also qualify
cover, mm under this section if the control of form dimensions, placing
of reinforcement, quality control of concrete, and curing
(a) Concrete exposed to earth or weather:
procedure are equal to that normally expected in a plant.
Wall panels:
No. 43 and No. 57 bars, prestressing
Concrete cover to pretensioned strand as described in this
tendons larger than 40 mm diameter ...............40
section is intended to provide minimum protection against
No. 36 bar and smaller, prestressing
weather and other effects. Such cover may not be sufficient to
tendons 40 mm diameter and smaller,
transfer or develop the stress in the strand, and it may be
MW200 and MD200 wire and smaller ..............20
necessary to increase the cover accordingly.
Other members:
No. 43 and No. 57 bars, prestressing
tendons larger than 40 mm diameter ...............50
No. 19 through No. 36 bars, prestressing
tendons larger than 16 mm diameter
through 40 mm diameter ..................................40
CODE COMMENTARY
No. 16 bar and smaller, prestressing tendons
16 mm diameter and smaller, MW200
and MD200 wire, and smaller .......................... 30
7.7.5 — Headed shear stud reinforcement R.7.7.5 — Headed shear stud reinforcement
For headed shear stud reinforcement, specified The shanks, the heads, and the base rails need to be
concrete cover for the heads or base rails shall not be protected by the specified concrete cover. For efficiency in
less than that required for the reinforcement in the type controlling inclined shear cracks, the overall height of the
of member in which the headed shear stud reinforce- headed stud assembly should be as large as permissible
ment is placed. (R11.11.5). The maximum overall height of the headed
study assembly is equal to the thickness of the member less
the sum of the specified concrete covers required for the
heads and base rails as shown in Fig. R7.7.5.
CODE COMMENTARY
7.7.6 — Corrosive environments R7.7.6 — Corrosive environments
In corrosive environments or other severe exposure Where concrete will be exposed to external sources of
conditions, amount of concrete protection shall be chlorides in service, such as deicing salts, brackish water,
suitably increased, and the pertinent requirements for seawater, or spray from these sources, concrete should be
concrete based on applicable exposure categories in proportioned to satisfy the requirements for the applicable
Chapter 4 shall be met, or other protection shall be exposure class in Chapter 4. These include minimum air
provided. content, maximum w/cm, minimum strength for normal-
weight and lightweight concrete, maximum chloride ion in
concrete, and cement type. Additionally, for corrosion
protection, a specified concrete cover for reinforcement not
7 less than 50 mm for walls and slabs and not less than 65 mm
for other members is recommended. For precast concrete
members manufactured under plant control conditions, a
specified concrete cover not less than 40 mm for walls and
slabs and not less than 50 mm for other members is
recommended.
7.7.6.1 — For prestressed concrete members R7.7.6.1 — Corrosive environments are defined in
exposed to corrosive environments or other severe Sections 4.2, R4.2.1, and R4.3.1. Additional information on
exposure categories such as those defined in Chapter 4, corrosion in parking structures is given in ACI 362.1R.7.12
and which are classified as Class T or C in 18.3.3,
specified concrete cover shall not be less than 1.5
times the cover for prestressed reinforcement required
by 7.7.2 and 7.7.3. This requirement shall be
permitted to be waived if the precompressed tensile
zone is not in tension under sustained loads.
7.8 — Reinforcement details for columns R7.8 — Reinforcement details for columns
CODE COMMENTARY
designed to resist 1-1/2 times the horizontal component
of the computed force in the inclined portion of an
offset bar. Lateral ties or spirals, if used, shall be
placed not more than 150 mm from points of bend.
Load transfer in structural steel cores of composite The 50 percent limit on transfer of compressive load by end
compression members shall be provided by the bearing on ends of structural steel cores is intended to provide
following: some tensile strength at such splices (up to 50 percent),
since the remainder of the total compressive stress in the
7.8.2.1 — Ends of structural steel cores shall be steel core are to be transmitted by dowels, splice plates,
accurately finished to bear at end bearing splices, with welds, etc. This provision should ensure that splices in
positive provision for alignment of one core above the composite compression members meet essentially the same
other in concentric contact. tensile strength as required for conventionally reinforced
concrete compression members.
7.8.2.2 — At end bearing splices, bearing shall be
considered effective to transfer not more than 50 percent
of the total compressive stress in the steel core.
7.9.1 — At connections of principal framing elements Confinement is essential at connections to ensure that the
(such as beams and columns), enclosure shall be flexural strength of the members can be developed without
provided for splices of continuing reinforcement and deterioration of the joint under repeated loadings.7.13,7.14
for anchorage of reinforcement terminating in such
connections.
CODE COMMENTARY
7.10 — Lateral reinforcement for R7.10 — Lateral reinforcement for
compression members compression members
7.10.3 — It shall be permitted to waive the lateral R7.10.3 — Precast columns with cover less than 40 mm,
reinforcement requirements of 7.10, 10.13, and 18.11 prestressed columns without longitudinal bars, columns
where tests and structural analysis show adequate smaller than minimum dimensions prescribed in earlier
strength and feasibility of construction. Code editions, columns of concrete with small size coarse
aggregate, wall-like columns, and other unusual cases may
require special designs for lateral reinforcement. Wire,
MW25, MD25, or larger, may be used for ties or spirals. If
such unusual columns are considered as spiral columns for
load strength in design, the volumetric reinforcement ratio
for the spiral, ρs, is to conform to 10.9.3.
Spiral reinforcement for compression members shall For practical considerations in cast-in-place construction,
conform to 10.9.3 and to the following: the minimum diameter of spiral reinforcement is 10 mm
(10 mm round, No. 10 bar, or equivalent deformed or plain
7.10.4.1 — Spirals shall consist of evenly spaced wire). This is the smallest size that can be used in a column
continuous bar or wire of such size and so assembled with 40 mm or more cover and having concrete compressive
to permit handling and placing without distortion from strengths of 21 MPa or more if the minimum clear spacing
designed dimensions. for placing concrete is to be maintained.
7.10.4.2 — For cast-in-place construction, size of Standard spiral sizes are 10, 13, and 16 mm diameter for hot
spirals shall not be less than 10 mm diameter. rolled or cold drawn material, plain or deformed.
7.10.4.3 — Clear spacing between spirals shall not The Code allows spirals to be terminated at the level of
exceed 75 mm, nor be less than 25 mm. See also 3.3.2. lowest horizontal reinforcement framing into the column.
However, if one or more sides of the column are not
7.10.4.4 — Anchorage of spiral reinforcement shall enclosed by beams or brackets, ties are required from the
be provided by 1-1/2 extra turns of spiral bar or wire at termination of the spiral to the bottom of the slab, drop
each end of a spiral unit. panel, or shear cap. If beams or brackets enclose all sides of
the column but are of different depths, the ties should extend
7.10.4.5 — Spiral reinforcement shall be spliced, if from the spiral to the level of the horizontal reinforcement
needed, by any one of the following methods: of the shallowest beam or bracket framing into the column.
These additional ties are to enclose the longitudinal column
(a) Lap splices not less than the larger of 300 mm and reinforcement and the portion of bars from beams bent into
the length indicated in one of (1) through (5) below: the column for anchorage. See also 7.9.
(1) deformed uncoated bar or wire............... 48db
Spirals should be held firmly in place, at proper pitch and
(2) plain uncoated bar or wire ...................... 72db
alignment, to prevent displacement during concrete placement.
(3) epoxy-coated deformed bar or wire ........ 72db
The Code has traditionally required spacers to hold the
(4) plain uncoated bar or wire with
fabricated spiral cage in place but was changed in 1989 to
a standard stirrup or tie hook in
allow alternate methods of installation. When spacers are
accordance with 7.1.3 at ends
used, the following may be used for guidance: for spiral bar
of lapped spiral reinforcement.
CODE COMMENTARY
The hooks shall be embedded
within the core confined by the spiral
reinforcement.......................................... 48db
(5) epoxy-coated deformed bar or wire
with a standard stirrup or tie hook
in accordance with 7.1.3 at ends
of lapped spiral reinforcement.
The hooks shall be embedded
within the core confined by the
spiral reinforcement ................................ 48db
(b) Full mechanical or welded splices in accordance
with 12.14.3. Fig. R7.10.5—Sketch to clarify measurements between
7
laterally supported column bars.
7.10.4.6 — Spirals shall extend from top of footing or
slab in any story to level of lowest horizontal reinforce-
ment in members supported above. or wire smaller than 16 mm diameter, a minimum of two
spacers should be used for spirals less than 500 mm in diameter,
7.10.4.7 — Where beams or brackets do not frame into three spacers for spirals 500 to 750 mm in diameter, and
all sides of a column, ties shall extend above termination four spacers for spirals greater than 750 mm in diameter.
of spiral to bottom of slab, drop panel, or shear cap. For spiral bar or wire 16 mm diameter or larger, a minimum
of three spacers should be used for spirals 600 mm or less in
7.10.4.8 — In columns with capitals, spirals shall diameter, and four spacers for spirals greater than 600 mm
extend to a level at which the diameter or width of in diameter. The project specifications or subcontract agree-
capital is two times that of the column. ments should be clearly written to cover the supply of
spacers or field tying of the spiral reinforcement. In the
7.10.4.9 — Spirals shall be held firmly in place and 1999 Code, splice requirements were modified for epoxy-
true to line. coated and plain spirals and to allow mechanical splices.
Tie reinforcement for compression members shall All longitudinal bars in compression should be enclosed
conform to the following: within lateral ties. Where longitudinal bars are arranged in a
circular pattern, only one circular tie per specified spacing is
7.10.5.1 — All nonprestressed bars shall be required. This requirement can be satisfied by a continuous
enclosed by lateral ties, at least No. 10 in size for circular tie (helix) at larger pitch than required for spirals
longitudinal bars No. 32 or smaller, and at least No. 13 under 10.9.3, the maximum pitch being equal to the
in size for No. 36, No. 43, No. 57, and bundled longitu- required tie spacing (see also 7.10.4.3).
dinal bars. Deformed wire or welded wire reinforcement
of equivalent area shall be permitted. The 1956 Code required “lateral support equivalent to that
provided by a 90-degree corner of a tie,” for every vertical
7.10.5.2 — Vertical spacing of ties shall not exceed 16 bar. Tie requirements were liberalized in 1963 by increasing
longitudinal bar diameters, 48 tie bar or wire diameters, the permissible included angle from 90 to 135 degrees and
or least dimension of the compression member. exempting bars that are located within 150 mm clear on
each side along the tie from adequately tied bars (see
7.10.5.3 — Ties shall be arranged such that every Fig. R7.10.5). Limited tests7.15 on full-size, axially-loaded,
corner and alternate longitudinal bar shall have lateral tied columns containing full-length bars (without splices)
support provided by the corner of a tie with an showed no appreciable difference between ultimate strengths
included angle of not more than 135 degrees and no of columns with full tie requirements and no ties at all.
bar shall be farther than 150 mm clear on each side
along the tie from such a laterally supported bar. Since spliced bars and bundled bars were not included in the
Where longitudinal bars are located around the perimeter tests of Reference 7.15, it is prudent to provide a set of ties
of a circle, a complete circular tie shall be permitted. at each end of lap spliced bars, above and below end-
bearing splices, and at minimum spacings immediately
7.10.5.4 — Ties shall be located vertically not more below sloping regions of offset bent bars.
than one-half a tie spacing above the top of footing or
slab in any story, and shall be spaced as provided
CODE COMMENTARY
herein to not more than one-half a tie spacing below Standard tie hooks are intended for use with deformed bars
the lowest horizontal reinforcement in slab, drop panel, only, and should be staggered where possible. See also 7.9.
or shear cap above.
Continuously wound bars or wires can be used as ties
provided their pitch and area are at least equivalent to the area
and spacing of separate ties. Anchorage at the end of a contin-
uously wound bar or wire should be by a standard hook as for
separate bars or by one additional turn of the tie pattern. A
circular continuously wound bar or wire is considered a spiral
if it conforms to 7.10.4, otherwise it is considered a tie.
7 7.10.5.5 — Where beams or brackets frame from R7.10.5.5 — With the 1983 Code, the wording of this
four directions into a column, termination of ties not more section was modified to clarify that ties may be terminated
than 75 mm below lowest reinforcement in shallowest of only when elements frame into all four sides of square and
such beams or brackets shall be permitted. rectangular columns; for round or polygonal columns, such
elements frame into the column from four directions.
7.10.5.6 — Where anchor bolts are placed in the top R7.10.5.6 — Provisions for confinement of anchor bolts
of columns or pedestals, the bolts shall be enclosed by that are placed in the top of columns or pedestals were
lateral reinforcement that also surrounds at least four added in the 2002 Code. Confinement improves load
vertical bars of the column or pedestal. The lateral transfer from the anchor bolts to the column or pier for
reinforcement shall be distributed within 125 mm of the situations where the concrete cracks in the vicinity of the bolts.
top of the column or pedestal, and shall consist of at Such cracking can occur due to unanticipated forces caused by
least two No. 13 or three No. 10 bars. temperature, restrained shrinkage, and similar effects.
7.11 — Lateral reinforcement for flexural R7.11 — Lateral reinforcement for flexural
members members
7.11.1 — Compression reinforcement in beams shall R7.11.1 — Compression reinforcement in beams and
be enclosed by ties or stirrups satisfying the size and girders should be enclosed to prevent buckling; similar
spacing limitations in 7.10.5 or by welded wire reinforce- requirements for such enclosure have remained essentially
ment of equivalent area. Such ties or stirrups shall be unchanged through several editions of the Code, except for
provided throughout the distance where compression minor clarification.
reinforcement is required.
7.12.1 — Reinforcement for shrinkage and temperature R7.12.1 — Shrinkage and temperature reinforcement is
stresses normal to flexural reinforcement shall be required at right angles to the principal reinforcement to
provided in structural slabs where the flexural reinforce- minimize cracking and to tie the structure together to ensure
ment extends in one direction only. it is acting as assumed in the design. The provisions of this
section are intended for structural slabs only; they are not
intended for slabs-on-ground.
CODE COMMENTARY
7.12.1.1 — Shrinkage and temperature reinforcement
shall be provided in accordance with either 7.12.2 or
7.12.3.
7.12.1.2 — Where shrinkage and temperature R7.12.1.2 — The area of shrinkage and temperature
movements are significantly restrained, the require- reinforcement required by 7.12.2.1 has been satisfactory where
ments of 8.2.4 and 9.2.3 shall be considered. shrinkage and temperature movements are permitted to
occur. Where structural walls or columns provide significant
restraint to shrinkage and temperature movements, the
restrain of volume changes causes tension in slabs, as well as
displacements, shear forces, and flexural moments in columns
or walls. In these cases, it may be necessary to increase the 7
amount of slab reinforcement required by 7.12.2.1 due to the
shrinkage and thermal effects in both principal directions (see
References 7.7 and 7.16). Topping slabs also experience
tension due to restraint of differential shrinkage between the
topping and the precast elements or metal deck (which has
zero shrinkage) that should be considered in reinforcing the
slab. Consideration should be given to strain demands on
reinforcement crossing joints of precast elements where most
of the restraint is likely to be relieved. Top and bottom rein-
forcement are both effective in controlling cracks. Control
strips during the construction period, which permit initial
shrinkage to occur without causing an increase in stresses, are
also effective in reducing cracks caused by restraint.
7.12.2 — Deformed reinforcement conforming to 3.5.3 R7.12.2 — The amounts specified for deformed bars and
used for shrinkage and temperature reinforcement welded wire reinforcement are empirical but have been used
shall be provided in accordance with the following: satisfactorily for many years. The area of reinforcement
given by 7.12.2.1 may be distributed near the top or bottom
7.12.2.1 — Area of shrinkage and temperature of the slab, or may be allocated between the two faces of the
reinforcement shall provide at least the following ratios slab as deemed appropriate for specific conditions. Splices
of reinforcement area to gross concrete area, but not and end anchorages of shrinkage and temperature reinforce-
less than 0.0014: ment are to be designed for the full specified yield strength
in accordance with 12.1, 12.15, 12.18, and 12.19.
(a) Slabs where Grade 280 or 530
deformed bars are used ................................. 0.0020
CODE COMMENTARY
7.12.3 — Prestressing steel conforming to 3.5.6 used R7.12.3 — Prestressed reinforcement requirements have
for shrinkage and temperature reinforcement shall be been selected to provide an effective force on the slab
provided in accordance with the following: approximately equal to the yield strength force for nonpre-
stressed shrinkage and temperature reinforcement. This
7.12.3.1 — Tendons shall be proportioned to provide amount of prestressing, 0.7 MPa on the gross concrete area,
a minimum average compressive stress of 0.7 MPa on has been successfully used on a large number of projects.
gross concrete area using effective prestress, after When the spacing of tendons used for shrinkage and
losses, in accordance with 18.6. temperature reinforcement exceeds 1.4 m, additional
bonded reinforcement is required at slab edges where the
7.12.3.2 — Spacing of tendons shall not exceed 1.8 m. prestressing forces are applied in order to adequately rein-
force the area between the slab edge and the point where
7.12.3.3 — When spacing of tendons exceeds 1.4 m, compressive stresses behind individual anchorages have
additional bonded shrinkage and temperature reinforce- spread sufficiently such that the slab is uniformly in
ment conforming to 7.12.2 shall be provided between compression. Application of the provisions of 7.12.3 to
the tendons at slab edges extending from the slab monolithic cast-in-place post-tensioned beam and slab
edge for a distance equal to the tendon spacing. construction is illustrated in Fig. R7.12.3.
7.13 — Requirements for structural integrity R7.13 — Requirements for structural integrity
7.13.1 — In the detailing of reinforcement and connec- Experience has shown that the overall integrity of a structure
tions, members of a structure shall be effectively tied can be substantially enhanced by minor changes in detailing
together to improve integrity of the overall structure. of reinforcement. It is the intent of this section of the Code
CODE COMMENTARY
to improve the redundancy and ductility in structures so that
in the event of damage to a major supporting element or an
abnormal loading event, the resulting damage may be
confined to a relatively small area and the structure will
have a better chance to maintain overall stability.
7.13.2 — For cast-in-place construction, the following R7.13.2 — With damage to a support, top reinforcement
shall constitute minimum requirements: that is continuous over the support, but not confined by
stirrups, will tend to tear out of the concrete and will not
7.13.2.1 — In joist construction, as defined in 8.13.1 provide the catenary action needed to bridge the damaged
through 8.13.3, at least one bottom bar shall be support. By making a portion of the bottom reinforcement
continuous or shall be spliced with a Class B tension continuous, catenary action can be provided. 7
splice or a mechanical or welded splice satisfying
12.14.3 and at noncontinuous supports shall be Requiring continuous top and bottom reinforcement in
anchored to develop fy at the face of the support using perimeter or spandrel beams provides a continuous tie
a standard hook satisfying 12.5 or headed deformed around the structure. It is not the intent to require a tensile
bar satisfying 12.6. tie of continuous reinforcement of constant size around the
entire perimeter of a structure, but simply to require that one
7.13.2.2 — Beams along the perimeter of the struc- half of the top flexural reinforcement required to extend past
ture shall have continuous reinforcement over the span the point of inflection by 12.12.3 be further extended and
length passing through the region bounded by the spliced at or near midspan. Similarly, the bottom reinforce-
longitudinal reinforcement of the column consisting of ment required to extend into the support by 12.11.1 should
(a) and (b): be made continuous or spliced with bottom reinforcement
from the adjacent span. If the depth of a continuous beam
(a) at least one-sixth of the tension reinforcement changes at a support, the bottom reinforcement in the deeper
required for negative moment at the support, but not member should be terminated with a standard hook and
less than two bars; bottom reinforcement in the shallower member should be
extended into and fully developed in the deeper member.
(b) at least one-quarter of the tension reinforcement
required for positive moment at midspan, but not less In the 2002 Code, provisions were added to permit the use
than two bars. of mechanical or welded splices for splicing reinforcement,
At noncontinuous supports, the reinforcement shall and the detailing requirements for the longitudinal reinforce-
be anchored to develop fy at the face of the support ment and stirrups in beams were revised. Section 7.13.2 was
using a standard hook satisfying 12.5 or headed revised in 2002 to require U-stirrups with not less than
deformed bar satisfying 12.6. 135-degree hooks around the continuous bars, or one-piece
closed stirrups to prevent the top continuous bars from
7.13.2.3 — The continuous reinforcement required in tearing out of the top of the beam. Section 7.13.2 was
7.13.2.2 shall be enclosed by transverse reinforcement revised in 2008 to require that the transverse reinforcement
of the type specified in 11.5.4.1. The transverse used to enclose the continuous reinforcement be of the type
reinforcement shall be anchored as specified in specified in 11.5.4.1 and anchored according to 11.5.4.2.
11.5.4.2. The transverse reinforcement need not be Figure R7.13.2 shows an example of a two-piece stirrup that
extended through the column. satisfies these requirements. Pairs of U-stirrups lapping one
another as defined in 12.13.5 are not permitted in perimeter
7.13.2.4 — Where splices are required to satisfy or spandrel beams. In the event of damage to the side
7.13.2.2, the top reinforcement shall be spliced at or concrete cover, the stirrups and top longitudinal reinforce-
near midspan and bottom reinforcement shall be ment may tend to tear out of the concrete. Thus, the top
spliced at or near the support. Splices shall be Class B longitudinal reinforcement will not provide the catenary
tension splices, or mechanical or welded splices satis- action needed to bridge over a damaged region. Further,
fying 12.14.3. lapped U-stirrups will not be effective at high torque (see
R11.5.4.1).
7.13.2.5 — In other than perimeter beams, where
transverse reinforcement as defined in 7.13.2.3 is Lap splices were changed from Class A to Class B in ACI
provided, there are no additional requirements for 318-08 to provide similar strength to that provided by
longitudinal integrity reinforcement. Where such trans- mechanical and welded splices satisfying 12.14.3. Class B
verse reinforcement is not provided, at least one- lap splices provide a higher level of reliability for abnormal
loading events.
CODE COMMENTARY
quarter of the positive moment reinforcement required
at midspan, but not less than two bars, shall pass
through the region bounded by the longitudinal reinforce-
ment of the column and shall be continuous or shall be
spliced over or near the support with a Class B tension
splice, or a mechanical or welded splice satisfying
12.14.3. At noncontinuous supports, the reinforcement
shall be anchored to develop fy at the face of the
support using a standard hook satisfying 12.5 or
headed deformed bar satisfying 12.6.
7.13.3 — For precast concrete construction, tension R7.13.3 — The Code requires tension ties for precast
ties shall be provided in the transverse, longitudinal, concrete buildings of all heights. Details should provide
and vertical directions and around the perimeter of the connections to resist applied loads. Connection details that
structure to effectively tie elements together. The rely solely on friction caused by gravity forces are not
provisions of 16.5 shall apply. permitted.
8.1.1 — In design of structural concrete, members R8.1.1 — The strength design method requires service
shall be proportioned for adequate strength in accor- loads or related internal moments and forces to be increased
dance with provisions of this Code, using load factors by specified load factors (required strength) and computed
and strength reduction factors φ specified in Chapter 9. nominal strengths to be reduced by specified strength reduc-
tion factors φ (design strength).
8.1.2 — Design of reinforced concrete using the R8.1.2 — Designs in accordance with Appendix B are
provisions of Appendix B shall be permitted. equally acceptable, provided the provisions of Appendix B 8
are used in their entirety.
8.1.3 — Anchors within the scope of Appendix D R8.1.3 — The Code included specific provisions for
installed in concrete to transfer loads between connected anchoring to concrete for the first time in the 2002 edition.
elements shall be designed using Appendix D. As has been done in the past with a number of new sections
and chapters, new material has been presented as an appendix.
8.2.1 — Design provisions of this Code are based on The provisions in the Code are for live, wind, and earth-
the assumption that structures shall be designed to quake loads such as those recommended in “Minimum
resist all applicable loads. Design Loads for Buildings and Other Structures”
(ASCE/SEI 7),8.1 formerly known as ANSI A58.1. If the
8.2.2 — Service loads shall be in accordance with the service loads specified by the general building code (of
general building code of which this Code forms a part, which this Code forms a part) differ from those of ASCE/
with such live load reductions as are permitted in the SEI 7, the general building code governs. However, if the
general building code. nature of the loads contained in a general building code differs
considerably from ASCE/SEI 7 loads, some provisions of
this Code may need modification to reflect the difference.
8.2.3 — In design for wind and earthquake loads, integral R8.2.3 — Any reinforced concrete wall that is monolithic
structural parts shall be designed to resist the total with other structural elements is considered to be an “integral
lateral loads. part.” Partition walls may or may not be integral structural
CODE COMMENTARY
parts. If partition walls may be removed, the primary lateral
load-resisting system should provide all of the required
resistance without contribution of the removable partition.
However, the effects of all partition walls attached to the
structure should be considered in the analysis of the struc-
ture because they may lead to increased design forces in
some or all elements. Provisions for seismic design are
given in Chapter 21.
8.2.4 — Consideration shall be given to effects of R8.2.4 — Information is reported on the magnitudes of
forces due to prestressing, crane loads, vibration, these various effects, especially the effects of column creep
impact, shrinkage, temperature changes, creep, and shrinkage in tall structures,8.2 and on procedures for
expansion of shrinkage-compensating concrete, and including the forces resulting from these effects in design.
8 unequal settlement of supports.
As described in R7.12.1.2, restraint of shrinkage and
temperature movements can cause significant tension in
slabs, as well as displacements, shear forces, and flexural
moments in columns or walls. In cases of restraint,
shrinkage and temperature reinforcement requirements may
exceed flexural reinforcement requirements.
8.3.1 — All members of frames or continuous construc- R8.3.1 — Factored loads are service loads multiplied by appro-
tion shall be designed for the maximum effects of priate load factors. For the strength design method, elastic
factored loads as determined by the theory of elastic analysis is used to obtain moments, shears, and reactions.
analysis, except as modified according to 8.4. It shall
be permitted to simplify design by using the assumptions
specified in 8.7 through 8.11.
8.3.3 — As an alternate to frame analysis, the following R8.3.3 — The approximate moments and shears give
approximate moments and shears shall be permitted reasonably conservative values for the stated conditions if
for design of continuous beams and one-way slabs the flexural members are part of a frame or continuous
(slabs reinforced to resist flexural stresses in only one construction. Because the load patterns that produce critical
direction), provided (a) through (e) are satisfied: values for moments in columns of frames differ from those
for maximum negative moments in beams, column
(a) There are two or more spans; moments should be evaluated separately.
(b) Spans are approximately equal, with the larger of
two adjacent spans not greater than the shorter by
more than 20 percent;
CODE COMMENTARY
Positive moment
End spans
Discontinuous end unrestrained ............. wu ln2/11
Discontinuous end integral with support .... wu ln2/14
Interior spans ............................................ wu ln2/16
8.3.4 — Strut-and-tie models shall be permitted to be R8.3.4 — The strut-and-tie model in Appendix A is based
used in the design of structural concrete. See on the assumption that portions of concrete structures can
Appendix A. be analyzed and designed using hypothetical pin-jointed
trusses consisting of struts and ties connected at nodes. This
design method can be used in the design of regions where
the basic assumptions of flexure theory are not applicable,
such as regions near force discontinuities arising from
concentrated forces or reactions, and regions near geometric
discontinuities, such as abrupt changes in cross section.
8.4.1 — Except where approximate values for Moment redistribution is dependent on adequate ductility in
moments are used, it shall be permitted to decrease plastic hinge regions. These plastic hinge regions develop at
factored moments calculated by elastic theory at sections of maximum positive or negative moment and
sections of maximum negative or maximum positive cause a shift in the elastic moment diagram. The usual result
moment in any span of continuous flexural members is a reduction in the values of maximum negative moments
for any assumed loading arrangement by not more in the support regions and an increase in the values of posi-
than 1000εt percent, with a maximum of 20 percent. tive moments between supports from those computed by
elastic analysis. However, because negative moments are
8.4.2 — Redistribution of moments shall be made only determined for one loading arrangement and positive
when εt is equal to or greater than 0.0075 at the moments for another (see 13.7.6 for an exception), econo-
section at which moment is reduced. mies in reinforcement can sometimes be realized by
reducing maximum elastic positive moments and increasing
negative moments, thus narrowing the envelope of
maximum negative and positive moments at any section in
the span. 8.3 The plastic hinges permit the utilization of the
CODE COMMENTARY
8.4.3 — The reduced moment shall be used for calcu- full capacity of more cross sections of a flexural member at
lating redistributed moments at all other sections ultimate loads.
within the spans. Static equilibrium shall be main-
tained after redistribution of moments for each loading Before 2008, the Code addressed moment redistribution by
arrangement. permitting an increase or decrease of factored negative
moments above or below elastically calculated values,
within specified limits. A decrease in negative moment
strength implies inelastic behavior in the negative moment
region at the support. By increasing the negative moment
strength, the positive moments can be reduced but the result
is that inelastic behavior will occur in the positive moment
region of the member and the percentage change in the positive
moment section could be much larger than the 20 percent
8 permitted for negative moment sections.8.3 The 2008
change places the same percentage limitations on both
positive and negative moments.
CODE COMMENTARY
Moment redistribution as permitted by 8.4 is not intended
for moments in two-way slab systems that are analyzed
using the pattern loadings given in 13.7.6.3 or for use where
approximate values of bending moments are used. For the
Direct Design Method, 10 percent modification is allowed
by 13.6.7.
8.5.1 — Modulus of elasticity, Ec , for concrete shall be R8.5.1 — Studies leading to the expression for modulus of
permitted to be taken as wc1.50.043 f c′ (in MPa) for elasticity of concrete in 8.5.1 are summarized in Reference
values of wc between 1440 and 2560 kg/m3. For 8.7 where Ec was defined as the slope of the line drawn
normalweight concrete, Ec shall be permitted to be from a stress of zero to a compressive stress of 0.45fc′ . The
taken as 4700 f c′ . modulus of elasticity for concrete is sensitive to the
modulus of elasticity of the aggregate and may differ from
the specified value. Measured values range typically from
120 to 80 percent of the specified value. Methods for deter-
mining the modulus of elasticity for concrete are described
in Reference 8.8.
8.6.1 — To account for the use of lightweight concrete, R8.6.1 — Factor λ reflects the lower tensile strength of light-
unless specifically noted otherwise, a modification weight concrete, which can reduce shear strength, friction
factor λ appears as a multiplier of f c′ in all applicable properties, splitting resistance, bond between concrete and
equations and sections of this Code, where λ = 0.85 reinforcement, and increase development length, compared
for sand-lightweight concrete and 0.75 for all-light- with normalweight concrete of the same compressive strength.
weight concrete. Linear interpolation between 0.75
and 0.85 shall be permitted, on the basis of volumetric Two alternative procedures are provided to determine λ. The
fractions, when a portion of the lightweight fine first alternative is based on the assumption that the tensile
aggregate is replaced with normalweight fine aggregate. strength of lightweight concrete is a fixed fraction of the
Linear interpolation between 0.85 and 1.0 shall be tensile strength of normalweight concrete.8.9 The multipliers
permitted, on the basis of volumetric fractions, for are based on data from tests on many types of structural
concrete containing normalweight fine aggregate and lightweight aggregate.
a blend of lightweight and normalweight coarse
aggregates. For normalweight concrete, λ = 1.0. If The second alternative is based on laboratory tests to deter-
average splitting tensile strength of lightweight mine the relationship between average splitting tensile
concrete, fct , is specified, λ = fct /(0.56 f c′ ) ≤ 1.0. strength fct and the specified compressive strength fc′ for the
lightweight concrete being used. For normalweight concrete,
the average splitting tensile strength fct is approximately
equal to 0.56 f c′ .8.9,8.10
CODE COMMENTARY
8.7 — Stiffness R8.7 — Stiffness
8.7.1 — Use of any set of reasonable assumptions R8.7.1 — Ideally, the member stiffnesses Ec I and GJ
shall be permitted for computing relative flexural and should reflect the degree of cracking and inelastic action
torsional stiffnesses of columns, walls, floors, and roof that has occurred along each member before yielding.
systems. The assumptions adopted shall be consistent However, the complexities involved in selecting different
throughout analysis. stiffnesses for all members of a frame would make frame
analyses inefficient in design offices. Simpler assumptions
are required to define flexural and torsional stiffnesses.
8.7.2 — Effect of haunches shall be considered both in R8.7.2 — Stiffness and fixed-end moment coefficients for
determining moments and in design of members. haunched members may be obtained from Reference 8.11.
8.8.1 — Lateral deflections of reinforced concrete R8.8.1 — The selection of appropriate effective stiffness
building systems resulting from service lateral loads values depends on the intended performance of the structure.
shall be computed by either a linear analysis with For wind loading, it is desirable to maintain elastic behavior
member stiffness determined using 1.4 times the flexural in members at service load conditions. When analyzing a
stiffness defined in 8.8.2 and 8.8.3 or by a more structure subjected to earthquake events at short recurrence
detailed analysis. Member properties shall not be intervals, some yielding without significant damage to the
taken greater than the gross section properties. members may be a tolerable performance objective. As with
lateral stability analysis of concrete structures (R10.10.4), a
factor of 1.4 times the stiffness used for analysis under
factored lateral loads is adequate to model effective section
properties for lateral deflection analysis under service loads.
Alternatively, a more accurate level of stiffness based on the
expected element performance can be determined.
8.8.2 — Lateral deflections of reinforced concrete R8.8.2 — The lateral deflection a structure sustains under
building systems resulting from factored lateral loads factored lateral loads can be substantially different from that
shall be computed either by linear analysis with calculated using linear analysis in part because of the
member stiffness defined by (a) or (b), or by a more inelastic response of the members and the decrease in effective
CODE COMMENTARY
detailed analysis considering the reduced stiffness of stiffness. The selection of appropriate effective stiffness for
all members under the loading conditions: reinforced concrete frame members has dual purposes: to
provide realistic estimates of lateral deflection and to
(a) By section properties defined in 10.10.4.1(a) determine deflection-imposed actions on the gravity system
through (c); or of the structure. A detailed nonlinear analysis of the struc-
ture would adequately capture these two effects. A simple
(b) 50 percent of stiffness values based on gross way to estimate an equivalent nonlinear lateral deflection
section properties. (δem at the top story in IBC 2006) using linear analysis is to
reduce the modeled stiffness of the concrete members in the
structure. The type of lateral load analysis affects the selection
of appropriate effective stiffness values. For analyses with
wind loading, where it is desirable to prevent nonlinear
action in the structure, effective stiffness representative of
pre-yield behavior may be appropriate. For earthquake 8
loading, a level of nonlinear behavior is tolerable depending
on the intended structural performance and earthquake
recurrence interval.
8.8.3 — Where two-way slabs without beams are R8.8.3 — Analysis of buildings with two-way slab systems
designated as part of the seismic-force-resisting without beams requires that the model represent the transfer
system, lateral deflections resulting from factored of lateral loads between vertical members. The model
lateral loads shall be permitted to be computed by should result in prediction of stiffness in substantial agree-
using linear analysis. The stiffness of slab members ment with results of comprehensive tests and analysis.
shall be defined by a model that is in substantial Several acceptable models have been proposed to accom-
agreement with results of comprehensive tests and plish this action.8.14-8.16
analysis and the stiffness of other frame members
shall be as defined in 8.8.2.
8.9.1 — Span length of members not built integrally Beam moments calculated at support centers may be
with supports shall be considered as the clear span reduced to the moments at support faces for design of
CODE COMMENTARY
plus the depth of the member, but need not exceed beams. Reference 8.17 provides an acceptable method of
distance between centers of supports. reducing moments at support centers to those at support
faces.
8.9.2 — In analysis of frames or continuous construction
for determination of moments, span length shall be
taken as the distance center-to-center of supports.
8.10.1 — Columns shall be designed to resist the axial Section 8.10 has been developed with the intent of making
forces from factored loads on all floors or roof and the certain that the most demanding combinations of axial load
maximum moment from factored loads on a single and moments be identified for design.
adjacent span of the floor or roof under consideration.
Loading condition giving the maximum ratio of Section 8.10.4 has been included to make certain that
moment to axial load shall also be considered. moments in columns are recognized in the design if the
girders have been proportioned using 8.3.3. The moment in
8.10.2 — In frames or continuous construction, 8.10.4 refers to the difference between the moments in a
consideration shall be given to the effect of unbalanced given vertical plane, exerted at column centerline by
floor or roof loads on both exterior and interior members framing into that column.
columns and of eccentric loading due to other causes.
8.11.1 — It shall be permitted to assume that: For determining column, wall, and beam moments and
shears caused by gravity loads, the Code permits the use of
(a) The live load is applied only to the floor or roof a model limited to the beams in the level considered and the
under consideration; and columns above and below that level. Far ends of columns
are to be considered as fixed for the purpose of analysis
(b) The far ends of columns built integrally with the under gravity loads. This assumption does not apply to
structure are considered to be fixed. lateral load analysis. However, in analysis for lateral loads,
8.11.2 — It shall be permitted to assume that the simplified methods (such as the portal method) may be used
arrangement of live load is limited to combinations of: to obtain the moments, shears, and reactions for structures
that are symmetrical and satisfy the assumptions used for
(a) Factored dead load on all spans with full factored such simplified methods. For unsymmetrical and high-rise
live load on two adjacent spans; and structures, rigorous methods recognizing all structural
displacements should be used.
CODE COMMENTARY
(b) Factored dead load on all spans with full factored The most demanding sets of design forces should be estab-
live load on alternate spans. lished by investigating the effects of live load placed in
various critical patterns.
8.12.1 — In T-beam construction, the flange and web This section contains provisions identical to those of
shall be built integrally or otherwise effectively bonded previous Codes for limiting dimensions related to stiffness
together. and flexural calculations. Provisions related to T-beams and 8
other flanged members are stated in 11.5.1 with regard to
8.12.2 — Width of slab effective as a T-beam flange torsion.
shall not exceed one-quarter of the span length of the
beam, and the effective overhanging flange width on
each side of the web shall not exceed:
CODE COMMENTARY
8.13 — Joist construction R8.13 — Joist construction
8.13.1 — Joist construction consists of a monolithic The size and spacing limitations for concrete joist construction
combination of regularly spaced ribs and a top slab meeting the limitations of 8.13.1 through 8.13.3 are based
arranged to span in one direction or two orthogonal on successful performance in the past.
directions.
8.13.3 — Clear spacing between ribs shall not exceed R8.13.3 — A limit on the maximum spacing of ribs is
750 mm. required because of the provisions permitting higher shear
8 strengths and less concrete protection for the reinforcement
for these relatively small, repetitive members.
CODE COMMENTARY
8.13.8 — For joist construction, Vc shall be permitted R8.13.8 — The increase in shear strength permitted by
to be 10 percent more than that specified in Chapter 11. 8.13.8 is justified on the basis of: (1) satisfactory perfor-
mance of joist construction with higher shear strengths,
designed under previous Codes, which allowed comparable
shear stresses, and (2) redistribution of local overloads to
adjacent joists.
8.14.1 — A floor finish shall not be included as part of The Code does not specify an additional thickness for
a structural member unless placed monolithically with wearing surfaces subjected to unusual conditions of wear.
the floor slab or designed in accordance with require- The need for added thickness for unusual wear is left to the
ments of Chapter 17. discretion of the licensed design professional.
8
8.14.2 — It shall be permitted to consider all concrete As in previous editions of the Code, a floor finish may be
floor finishes as part of required cover or total thickness considered for strength purposes only if it is cast mono-
for nonstructural considerations. lithically with the slab. Permission is given to include a
separate finish in the structural thickness if composite action
is provided for in accordance with Chapter 17.
9.1.1 — Structures and structural members shall be In the 2002 Code, the load factor combinations and strength
designed to have design strengths at all sections at reduction factors of the 1999 Code were revised and moved
least equal to the required strengths calculated for the to Appendix C. The 1999 combinations were replaced with
factored loads and forces in such combinations as are those of SEI/ASCE 7-02.9.1 The strength reduction factors
stipulated in this Code. were replaced with those of the 1999 Appendix C, except
that the factor for flexure was increased.
9.1.2 — Members also shall meet all other require-
ments of this Code to ensure adequate performance at The changes were made to further unify the design profession
service load levels. on one set of load factors and combinations, and to facilitate
the proportioning of concrete building structures that 9
9.1.3 — Design of structures and structural members include members of materials other than concrete. When
using the load factor combinations and strength reduc- used with the strength reduction factors in 9.3, the designs
tion factors of Appendix C shall be permitted. Use of for gravity loads will be comparable to those obtained using
load factor combinations from this chapter in conjunction the strength reduction and load factors of the 1999 and
with strength reduction factors of Appendix C shall not earlier Codes. For combinations with lateral loads, some
be permitted. designs will be different, but the results of either set of load
factors are considered acceptable.
φ (Nominal Strength) ≥ U
9.2.1 — Required strength U shall be at least equal to The required strength U is expressed in terms of factored
the effects of factored loads in Eq. (9-1) through (9-7). loads, or related internal moments and forces. Factored
The effect of one or more loads not acting simulta- loads are the loads specified in the general building code
neously shall be investigated. multiplied by appropriate load factors.
U = 1.4(D + F ) (9-1) The factor assigned to each load is influenced by the degree
of accuracy to which the load effect usually can be calculated
U = 1.2(D + F + T) + 1.6(L + H) (9-2) and the variation that might be expected in the load during
the lifetime of the structure. Dead loads, because they are
+ 0.5(Lr or S or R) more accurately determined and less variable, are assigned a
lower load factor than live loads. Load factors also account
U = 1.2D + 1.6(Lr or S or R) + (1.0L or 0.8W) (9-3) for variability in the structural analysis used to compute
moments and shears.
U = 1.2D + 1.6W + 1.0L + 0.5(Lr or S or R) (9-4)
The Code gives load factors for specific combinations of
loads. In assigning factors to combinations of loading, some
CODE COMMENTARY
U = 1.2D + 1.0E + 1.0L + 0.2S (9-5) consideration is given to the probability of simultaneous
occurrence. While most of the usual combinations of loadings
U = 0.9D + 1.6W + 1.6H (9-6) are included, it should not be assumed that all cases are
covered.
U = 0.9D + 1.0E + 1.6H (9-7)
Due regard is to be given to sign in determining U for
except as follows: combinations of loadings, as one type of loading may
produce effects of opposite sense to that produced by another
(a) The load factor on the live load L in Eq. (9-3) to type. The load combinations with 0.9D are specifically
(9-5) shall be permitted to be reduced to 0.5 except for included for the case where a higher dead load reduces the
garages, areas occupied as places of public assembly, effects of other loads. The loading case may also be critical
and all areas where L is greater than 4.8 kN/m2. for tension-controlled column sections. In such a case, a
reduction in axial load and an increase in moment may
(b) Where wind load W has not been reduced by a result in a critical load combination.
directionality factor, it shall be permitted to use 1.3W
9 in place of 1.6W in Eq. (9-4) and (9-6). Consideration should be given to various combinations of
loading to determine the most critical design condition. This
(c) Where E, the load effects of earthquake, is based is particularly true when strength is dependent on more than
on service-level seismic forces, 1.4E shall be used in one load effect, such as strength for combined flexure and
place of 1.0E in Eq. (9-5) and (9-7). axial load or shear strength in members with axial load.
(d) The load factor on H, loads due to weight and
pressure of soil, water in soil, or other materials, If unusual circumstances require greater reliance on the
shall be set equal to zero in Eq. (9-6) and (9-7) if the strength of particular members than encountered in usual
structural action due to H counteracts that due to W practice, some reduction in the stipulated strength reduction
or E. Where lateral earth pressure provides resis- factors φ or increase in the stipulated load factors may be
tance to structural actions from other forces, it shall appropriate for such members.
not be included in H but shall be included in the
design resistance. R9.2.1(a) — The load modification factor of 9.2.1(a) is
different than the live load reductions based on the loaded
area that may be allowed in the legally adopted general
building code. The live load reduction, based on loaded
area, adjusts the nominal live load (L0 in ASCE/SEI 7) to L.
The live load reduction as specified in the legally adopted
general building code can be used in combination with the
0.5 load factor specified in 9.2.1(a).
9.2.2 — If resistance to impact effects is taken into R9.2.2 — If the live load is applied rapidly, as may be the
account in design, such effects shall be included with L. case for parking structures, loading docks, warehouse floors,
CODE COMMENTARY
elevator shafts, etc., impact effects should be considered. In all
equations, substitute (L + impact) for L when impact should
be considered.
9.2.3 — Estimations of differential settlement, creep, R9.2.3 — The effects of differential settlement, creep,
shrinkage, expansion of shrinkage-compensating shrinkage, temperature, and shrinkage-compensating concrete
concrete, or temperature change shall be based on a should be considered. The term “realistic assessment” is
realistic assessment of such effects occurring in used to indicate that the most probable values rather than the
service. upper bound values of the variables should be used.
9.2.4 — If a structure is in a flood zone, or is subjected R9.2.4 — Areas subject to flooding are defined by flood
to forces from atmospheric ice loads, the flood or ice hazard maps, usually maintained by local governmental
loads and the appropriate load combinations of ASCE/ jurisdictions.
SEI 7 shall be used.
9.2.5 — For post-tensioned anchorage zone design, a R9.2.5 — The load factor of 1.2 applied to the maximum
9
load factor of 1.2 shall be applied to the maximum tendon jacking force results in a design load of about
prestressing steel jacking force. 113 percent of the specified prestressing steel yield strength
but not more than 96 percent of the nominal ultimate strength
of the prestressing steel. This compares well with the
maximum attainable jacking force, which is limited by the
anchor efficiency factor.
9.3.1 — Design strength provided by a member, its R9.3.1 — The design strength of a member refers to the
connections to other members, and its cross sections, nominal strength calculated in accordance with the
in terms of flexure, axial load, shear, and torsion, shall requirements stipulated in this Code multiplied by a
be taken as the nominal strength calculated in accor- strength reduction factor φ, which is always less than 1.
dance with requirements and assumptions of this
The purposes of the strength reduction factor φ are: (1) to
Code, multiplied by the strength reduction factors φ in
allow for the probability of under-strength members due to
9.3.2, 9.3.4, and 9.3.5.
variations in material strengths and dimensions, (2) to allow
for inaccuracies in the design equations, (3) to reflect the
degree of ductility and required reliability of the member
under the load effects being considered, and (4) to reflect
the importance of the member in the structure.9.7,9.8
CODE COMMENTARY
9.3.2 — Strength reduction factor φ shall be as given in
9.3.2.1 through 9.3.2.7:
9.3.2.1 — Tension-controlled sections as R9.3.2.1 — In applying 9.3.2.1 and 9.3.2.2, the axial
defined in 10.3.4 ....................................................0.90 tensions and compressions to be considered are those
(See also 9.3.2.7) caused by external forces. Effects of prestressing forces are
not included.
9.3.2.2 — Compression-controlled sections, as R9.3.2.2 — Before the 2002 edition, the Code specified
defined in 10.3.3: the magnitude of the φ-factor for cases of axial load or
flexure, or both, in terms of the type of loading. For these
(a) Members with spiral reinforcement cases, the φ-factor is now determined by the strain conditions
conforming to 10.9.3...........................................0.75 at a cross section, at nominal strength.
(b) Other reinforced members ............................0.65 A lower φ-factor is used for compression-controlled
9 For sections in which the net tensile strain in the sections than is used for tension-controlled sections because
extreme tension steel at nominal strength, εt , is compression-controlled sections have less ductility, are
between the limits for compression-controlled and more sensitive to variations in concrete strength, and generally
tension-controlled sections, φ shall be permitted to be occur in members that support larger loaded areas than
linearly increased from that for compression-controlled members with tension-controlled sections. Members with
sections to 0.90 as εt increases from the compression- spiral reinforcement are assigned a higher φ than tied
controlled strain limit to 0.005. columns because they have greater ductility or toughness.
Alternatively, when Appendix B is used, for members For sections subjected to axial load with flexure, design
in which fy does not exceed 420 MPa, with symmetric strengths are determined by multiplying both Pn and Mn by
reinforcement, and with (d – d′)/h not less than 0.70, φ the appropriate single value of φ. Compression-controlled
shall be permitted to be increased linearly to 0.90 as and tension-controlled sections are defined in 10.3.3 and
φPn decreases from 0.10fc′ Ag to zero. For other 10.3.4 as those that have net tensile strain in the extreme
reinforced members, φ shall be permitted to be tension steel at nominal strength less than or equal to the
increased linearly to 0.90 as φPn decreases from compression-controlled strain limit, and equal to or greater
0.10fc′ Ag or φPb , whichever is smaller, to zero. than 0.005, respectively. For sections with net tensile strain
εt in the extreme tension steel at nominal strength between
the above limits, the value of φ may be determined by linear
interpolation, as shown in Fig. R9.3.2. The concept of net
tensile strain εt is discussed in R10.3.3.
CODE COMMENTARY
Since the compressive strain in the concrete at nominal
strength is assumed in 10.2.3 to be 0.003, the net tensile
strain limits for compression-controlled members may also
be stated in terms of the ratio c/dt , where c is the depth of
the neutral axis at nominal strength, and dt is the distance
from the extreme compression fiber to the extreme tension
steel. The c/dt limits for compression-controlled and
tension-controlled sections are 0.6 and 0.375, respectively.
The 0.6 limit applies to sections reinforced with Grade 420
steel and to prestressed sections. Figure R9.3.2 also gives
equations for φ as a function of c/dt.
9.3.2.5 — Post-tensioned anchorage zones ...... 0.85 R9.3.2.5 — The φ-factor of 0.85 reflects the wide scatter of
results of experimental anchorage zone studies. Since 18.13.4.2
limits the nominal compressive strength of unconfined
concrete in the general zone to 0.7λfci′, the effective design
strength for unconfined concrete is 0.85 × 0.7λfci′ ≈ 0.6λfci′ .
9.3.2.6 — Strut-and-tie models (Appendix A), R9.3.2.6 — The φ-factor used in strut-and-tie models is
and struts, ties, nodal zones, and bearing taken equal to the φ-factor for shear. The value of φ for strut-
areas in such models ............................................ 0.75 and-tie models is applied to struts, ties, and bearing areas in
such models.
9.3.2.7 — Flexural sections in pretensioned R9.3.2.7 — If a critical section occurs in a region where
members where strand embedment is less than the strand is not fully developed, failure may be by bond slip.
development length as provided in 12.9.1.1: Such a failure resembles a brittle shear failure; hence, the
requirements for a reduced φ. For sections between the end
(a) From the end of the member to the end of the transfer length and the end of the development length,
of the transfer length .......................................... 0.75 the value of φ may be determined by linear interpolation, as
shown in Fig. R9.3.2.7(a) and (b).
(b) From the end of the transfer length to
the end of the development length φ Where bonding of one or more strands does not extend to
shall be permitted to be linearly the end of the member, instead of a more rigorous analysis,
increased from ........................................ 0.75 to 0.9. φ may be conservatively taken as 0.75 from the end of the
Where bonding of a strand does not extend to the member to the end of the transfer length of the strand with the
end of the member, strand embedment shall be longest debonded length. Beyond this point, φ may be varied
assumed to begin at the end of the debonded linearly to 0.9 at the location where all strands are developed,
length. See also 12.9.3. as shown in Fig. R9.3.2.7(b). Alternatively, the contribution of
the debonded strands may be ignored until they are fully
developed. Embedment of debonded strand is considered to
begin at the termination of the debonding sleeves. Beyond
this point, the provisions of 12.9.3 are applicable.
CODE COMMENTARY
9.3.3 — Development lengths specified in Chapter 12
do not require a φ-factor.
9.3.4 — For structures that rely on intermediate R9.3.4 — Section 9.3.4(a) refers to brittle members such as
precast structural walls in Seismic Design Category D, low-rise walls, portions of walls between openings, or
E, or F, special moment frames, or special structural diaphragms that are impractical to reinforce to raise their
walls to resist earthquake effects, E, φ shall be modified nominal shear strength above nominal flexural strength for
as given in (a) through (c): the pertinent loading conditions.
(a) For any structural member that is designed to Short structural walls were the primary vertical elements of
resist E, φ for shear shall be 0.60 if the nominal the lateral-force-resisting system in many of the parking
shear strength of the member is less than the shear structures that sustained damage during the 1994
corresponding to the development of the nominal Northridge earthquake. Section 9.3.4(b) requires the shear
flexural strength of the member. The nominal flexural strength reduction factor for diaphragms to be 0.60 if the
strength shall be determined considering the most shear strength reduction factor for the walls is 0.60.
critical factored axial loads and including E;
CODE COMMENTARY
9.3.5 — In Chapter 22, φ shall be 0.60 for flexure, R9.3.5 — The strength reduction factor φ for structural plain
compression, shear, and bearing of structural plain concrete design is the same for all strength conditions. Since
concrete. both flexural tension strength and shear strength for plain
concrete depend on the tensile strength characteristics of the
concrete, with no reserve strength or ductility possible due to
the absence of reinforcement, equal strength reduction factors
for both bending and shear are considered appropriate. In
the 2008 Code, the factor was increased to 0.60 based on
reliability analyses and statistical study of concrete prop-
erties,9.10 as well as calibration to past practice.
9.4 — Design strength for reinforcement R9.4 — Design strength for reinforcement
The values of fy and fyt used in design calculations In addition to the upper limit of 550 MPa for yield strength
shall not exceed 550 MPa, except for prestressing of nonprestressed reinforcement, there are limitations on
steel and for transverse reinforcement in 10.9.3 and yield strength in other sections of the Code. 9
21.1.5.4.
In 11.4.2, 11.5.3.4, 11.6.6, and 18.9.3.2, the maximum
value of fy or fyt that may be used in design is 420 MPa,
except that fy or fyt up to 550 MPa may be used for shear
reinforcement meeting the requirements of ASTM A497M.
9.5.1 — Reinforced concrete members subjected to R9.5.1 — The provisions of 9.5 are concerned only with
flexure shall be designed to have adequate stiffness to deflections or deformations that may occur at service load
limit deflections or any deformations that adversely levels. When long-term deflections are computed, only the
affect strength or serviceability of a structure. dead load and that portion of the live load that is sustained
need be considered.
CODE COMMENTARY
9.5.2 — One-way construction (nonprestressed) R9.5.2 — One-way construction (nonprestressed)
9.5.2.1 — Minimum thickness stipulated in Table 9.5(a) R9.5.2.1 — The minimum thicknesses of Table 9.5(a)
shall apply for one-way construction not supporting or apply for nonprestressed beams and one-way slabs (see
attached to partitions or other construction likely to be 9.5.2), and for composite members (see 9.5.5). These
damaged by large deflections, unless computation of minimum thicknesses apply only to members not supporting
deflection indicates a lesser thickness can be used or attached to partitions and other construction likely to be
without adverse effects. damaged by deflection.
9.5.2.2 — Where deflections are to be computed, R9.5.2.2 — For calculation of immediate deflections of
deflections that occur immediately on application of uncracked prismatic members, the usual methods or
load shall be computed by usual methods or formulas formulas for elastic deflections may be used with a constant
for elastic deflections, considering effects of cracking value of EcIg along the length of the member. However, if
and reinforcement on member stiffness. the member is cracked at one or more sections, or if its
depth varies along the span, a more exact calculation
becomes necessary.
CODE COMMENTARY
9.5.2.3 — Unless stiffness values are obtained by a R9.5.2.3 — The effective moment of inertia procedure
more comprehensive analysis, immediate deflection described in the Code and developed in Reference 9.15 was
shall be computed with the modulus of elasticity for selected as being sufficiently accurate for use to control
concrete, Ec , as specified in 8.5.1 (normalweight or deflections.9.16-9.18 The effective moment of inertia Ie was
lightweight concrete) and with the effective moment of developed to provide a transition between the upper and
inertia, Ie , as follows, but not greater than Ig lower bounds of Ig and Icr as a function of the ratio Mcr /Ma.
For most cases, Ie will be less than Ig.
M cr⎞ 3 M cr⎞ 3
I e = ⎛ ---------
- I g + 1 – ⎛ --------- I (9-8)
⎝M ⎠ ⎝ M -⎠ cr
a a
where
fr Ig
M cr = --------
- (9-9)
yt
9
and
fr = 0.62λ f c′ (9-10)
9.5.2.4 — For continuous members, Ie shall be R9.5.2.4 — For continuous members, the Code procedure
permitted to be taken as the average of values suggests a simple averaging of Ie values for the positive and
obtained from Eq. (9-8) for the critical positive and negative moment sections. The use of the midspan section
negative moment sections. For prismatic members, Ie properties for continuous prismatic members is considered
shall be permitted to be taken as the value obtained satisfactory in approximate calculations primarily because
from Eq. (9-8) at midspan for simple and continuous the midspan rigidity (including the effect of cracking) has
spans, and at support for cantilevers. the dominant effect on deflections, as shown by ACI
Committee 4359.19,9.20 and SP-43.9.13
9.5.2.5 — Unless values are obtained by a more R9.5.2.5 — Shrinkage and creep due to sustained loads
comprehensive analysis, additional long-term deflection cause additional long-term deflections over and above those
resulting from creep and shrinkage of flexural members that occur when loads are first placed on the structure. Such
(normalweight or lightweight concrete) shall be deter- deflections are influenced by temperature, humidity, curing
mined by multiplying the immediate deflection caused conditions, age at time of loading, quantity of compression
by the sustained load considered, by the factor λΔ reinforcement, and magnitude of the sustained load. The
expression given in this section is considered satisfactory
ξ for use with the Code procedures for the calculation of
λ Δ = ---------------------- (9-11) immediate deflections, and with the limits given in Table
1 + 50ρ′
9.5(b). The deflection computed in accordance with this
where ρ′ shall be the value at midspan for simple and section is the additional long-term deflection due to the
continuous spans, and at support for cantilevers. It dead load and that portion of the live load that will be
shall be permitted to assume ξ, the time-dependent sustained for a sufficient period to cause significant time-
factor for sustained loads, to be equal to: dependent deflections.
CODE COMMENTARY
9.5.2.6 — Deflection computed in accordance with R9.5.2.6 — It should be noted that the limitations given
9.5.2.2 through 9.5.2.5 shall not exceed limits stipulated in this table relate only to supported or attached nonstruc-
9 in Table 9.5(b). tural elements. For those structures in which structural
members are likely to be affected by deflection or deformation
of members to which they are attached in such a manner as
to affect adversely the strength of the structure, these
deflections and the resulting forces should be considered
explicitly in the analysis and design of the structures as
required by 9.5.1. (See Reference 9.18.)
CODE COMMENTARY
9.5.3.2 — For slabs without interior beams spanning R9.5.3.2 — The minimum thicknesses in Table 9.5(c) are
between the supports and having a ratio of long to short those that have been developed through the years. Slabs
span not greater than 2, the minimum thickness shall be conforming to those limits have not resulted in systematic
in accordance with the provisions of Table 9.5(c) and problems related to stiffness for short- and long-term loads.
shall not be less than the following values: These limits apply to only the domain of previous experience
in loads, environment, materials, boundary conditions, and
(a) Slabs without drop panels as spans.
defined in 13.2.5.......................................... 125 mm;
(b) Slabs with drop panels as defined
in 13.2.5 ...................................................... 100 mm.
9.5.3.3 — For slabs with beams spanning between R9.5.3.3 — For panels having a ratio of long to short span
the supports on all sides, the minimum thickness, h, greater than 2, the use of Eq. (9-12) and (9-13), which express
shall be as follows: the minimum thickness as a fraction of the long span, may
give unreasonable results. For such panels, the rules
(a) For αfm equal to or less than 0.2, the provisions applying to one-way construction in 9.5.2 should be used. 9
of 9.5.3.2 shall apply;
(b) For αfm greater than 0.2 but not greater than 2.0, The requirement in 9.5.3.3(a) for αfm equal to 0.2 made it
h shall not be less than possible to eliminate Eq. (9-13) of the 1989 Code. That
equation gave values essentially the same as those in
Table 9.5(c), as does Eq. (9-12) at a value of αfm equal to 0.2.
fy ⎞
l n ⎛ 0.8 + ------------ -
⎝ 1400⎠
h = ------------------------------------------------- (9-12)
36 + 5β ( α fm – 0.2 )
(c) For αfm greater than 2.0, h shall not be less than
fy ⎞
l n ⎛ 0.8 + ------------ -
⎝ 1400⎠
h = --------------------------------------- (9-13)
36 + 9β
CODE COMMENTARY
shall be increased by at least 10 percent in the panel
with a discontinuous edge.
9.5.3.4 — Slab thickness less than the minimum R9.5.3.4 — The calculation of deflections for slabs is
required by 9.5.3.1, 9.5.3.2, and 9.5.3.3 shall be complicated even if linear elastic behavior can be assumed.
permitted where computed deflections do not exceed For immediate deflections, the values of Ec and Ie specified
the limits of Table 9.5(b). Deflections shall be computed in 9.5.2.3 may be used.9.18 However, other procedures and
taking into account size and shape of the panel, condi- other values of the stiffness Ec Ie may be used if they result
tions of support, and nature of restraints at the panel in predictions of deflection in reasonable agreement with
edges. The modulus of elasticity of concrete, Ec , shall the results of comprehensive tests.
be as specified in 8.5.1. The effective moment of inertia,
9
Ie , shall be that given by Eq. (9-8); other values shall be Since available data on long-term deflections of slabs are too
permitted to be used if they result in computed deflec- limited to justify more elaborate procedures, the additional
tions in reasonable agreement with results of compre- long-term deflection for two-way construction is required to
hensive tests. Additional long-term deflection shall be be computed using the multipliers given in 9.5.2.5.
computed in accordance with 9.5.2.5.
9.5.4.1 — For flexural members designed in accor- R9.5.4.1 — Immediate deflections of Class U prestressed
dance with provisions of Chapter 18, immediate concrete members may be calculated by the usual methods
deflection shall be computed by usual methods or or formulas for elastic deflections using the moment of
formulas for elastic deflections, and the moment of inertia of the gross (uncracked) concrete section and the
inertia of the gross concrete section, Ig , shall be modulus of elasticity for concrete specified in 8.5.1.
permitted to be used for Class U flexural members, as
defined in 18.3.3.
9.5.4.2 — For Class C and Class T flexural R9.5.4.2 — Class C and Class T prestressed flexural
members, as defined in 18.3.3, deflection calculations members are defined in 18.3.3. Reference 9.23 gives infor-
shall be based on a cracked transformed section mation on deflection calculations using a bilinear moment-
analysis. It shall be permitted to base computations on deflection relationship and using an effective moment of
a bilinear moment-deflection relationship, or an effective inertia. Reference 9.24 gives additional information on
moment of inertia, Ie , as defined by Eq. (9-8). deflection of cracked prestressed concrete members.
CODE COMMENTARY
Prestressed concrete members shorten more with time than
similar nonprestressed members due to the precompression
in the slab or beam, which causes axial creep. This creep
together with concrete shrinkage results in significant short-
ening of the flexural members that continues for several
years after construction and should be considered in design.
The shortening tends to reduce the tension in the prestressing
steel, reducing the precompression in the member and thereby
causing increased long-term deflections.
9.5.5.1 — Shored construction Since few tests have been made to study the immediate and
long-term deflections of composite members, the rules
If composite flexural members are supported during given in 9.5.5.1 and 9.5.5.2 are based on the judgment of
construction so that, after removal of temporary ACI Committee 318 and on experience.
supports, dead load is resisted by the full composite
section, it shall be permitted to consider the composite If any portion of a composite member is prestressed or if the
member equivalent to a monolithically cast member for member is prestressed after the components have been cast,
computation of deflection. For nonprestressed the provisions of 9.5.4 apply and deflections are to be calcu-
members, the portion of the member in compression lated. For nonprestressed composite members, deflections
shall determine whether values in Table 9.5(a) for need to be calculated and compared with the limiting values
normalweight or lightweight concrete shall apply. If in Table 9.5(b) only when the thickness of the member or
deflection is computed, account shall be taken of the precast part of the member is less than the minimum
curvatures resulting from differential shrinkage of thickness given in Table 9.5(a). In unshored construction,
precast and cast-in-place components, and of axial the thickness of concern depends on whether the deflection
creep effects in a prestressed concrete member. before or after the attainment of effective composite action
is being considered. (In Chapter 17, it is stated that distinction
9.5.5.2 — Unshored construction need not be made between shored and unshored members.
This refers to strength calculations, not to deflections.)
If the thickness of a nonprestressed precast flexural
member meets the requirements of Table 9.5(a),
CODE COMMENTARY
deflection need not be computed. If the thickness of a
nonprestressed composite member meets the require-
ments of Table 9.5(a), it is not required to compute
deflection occurring after the member becomes
composite, but the long-term deflection of the precast
member shall be investigated for magnitude and duration
of load prior to beginning of effective composite action.
CODE COMMENTARY
10.1 — Scope
10.2.1 — Strength design of members for flexure and R10.2.1 — The strength of a member computed by the
axial loads shall be based on assumptions given in strength design method of the Code requires that two basic
10.2.2 through 10.2.7, and on satisfaction of applicable conditions be satisfied: (1) static equilibrium, and (2)
conditions of equilibrium and compatibility of strains. compatibility of strains. Equilibrium between the compressive
and tensile forces acting on the cross section at nominal
10
strength should be satisfied. Compatibility between the
stress and strain for the concrete and the reinforcement at
nominal strength conditions should also be established
within the design assumptions allowed by 10.2.
10.2.2 — Strain in reinforcement and concrete shall be R10.2.2 — Many tests have confirmed that the distribution
assumed directly proportional to the distance from the of strain is essentially linear across a reinforced concrete
neutral axis, except that, for deep beams as defined in cross section, even near ultimate strength.
10.7.1, an analysis that considers a nonlinear distri-
bution of strain shall be used. Alternatively, it shall be The strain in both reinforcement and in concrete is assumed
permitted to use a strut-and-tie model. See 10.7, 11.7, to be directly proportional to the distance from the neutral
and Appendix A. axis. This assumption is of primary importance in design for
determining the strain and corresponding stress in the
reinforcement.
10.2.3 — Maximum usable strain at extreme concrete R10.2.3 — The maximum concrete compressive strain at
compression fiber shall be assumed equal to 0.003. crushing of the concrete has been observed in tests of
various kinds to vary from 0.003 to higher than 0.008 under
special conditions. However, the strain at which ultimate
moments are developed is usually about 0.003 to 0.004 for
members of normal proportions and materials.
10.2.4 — Stress in reinforcement below fy shall be R10.2.4 — For deformed reinforcement, it is reasonably
taken as Es times steel strain. For strains greater than accurate to assume that the stress in reinforcement is
that corresponding to fy , stress in reinforcement shall proportional to strain below the specified yield strength fy.
be considered independent of strain and equal to fy . The increase in strength due to the effect of strain hardening
of the reinforcement is neglected for strength computations.
In strength computations, the force developed in tensile or
compressive reinforcement is computed as:
As fs = AsEsεs
when εs ≥ εy
As fs = As fy
CODE COMMENTARY
where εs is the value from the strain diagram at the location
of the reinforcement. For design, the modulus of elasticity
of steel reinforcement Es may be taken as 200,000 MPa
(see 8.5.2).
10.2.5 — Tensile strength of concrete shall be R10.2.5 — The tensile strength of concrete in flexure
neglected in axial and flexural calculations of reinforced (modulus of rupture) is a more variable property than the
concrete, except when meeting requirements of 18.4. compressive strength and is about 10 to 15 percent of the
compressive strength. Tensile strength of concrete in flexure
is neglected in strength design. For members with normal
percentages of reinforcement, this assumption is in good agree-
ment with tests. For very small percentages of reinforcement,
neglect of the tensile strength at ultimate is usually correct.
10 10.2.6 — The relationship between concrete R10.2.6 — This assumption recognizes the inelastic stress
compressive stress distribution and concrete strain distribution of concrete at high stress. As maximum stress is
shall be assumed to be rectangular, trapezoidal, approached, the stress-strain relationship for concrete is not
parabolic, or any other shape that results in prediction a straight line but some form of a curve (stress is not propor-
of strength in substantial agreement with results of tional to strain). The general shape of a stress-strain curve is
comprehensive tests. primarily a function of concrete strength and consists of a
rising curve from zero to a maximum at a compressive
strain between 0.0015 and 0.002 followed by a descending
curve to an ultimate strain (crushing of the concrete) from
0.003 to higher than 0.008. As discussed under R10.2.3, the
Code sets the maximum usable strain at 0.003 for design.
10.2.7 — Requirements of 10.2.6 are satisfied by an R10.2.7 — For design, the Code allows the use of an
equivalent rectangular concrete stress distribution equivalent rectangular compressive stress distribution
defined by the following: (stress block) to replace the more exact concrete stress
distribution. In the equivalent rectangular stress block, an
10.2.7.1 — Concrete stress of 0.85fc′ shall be average stress of 0.85fc′ is used with a rectangle of depth a =
assumed uniformly distributed over an equivalent β1c. The β1 of 0.85 for concrete with fc′ ≤ 28 MPa and 0.05
compression zone bounded by edges of the cross less for each 7 MPa of fc′ in excess of 28 MPa was deter-
section and a straight line located parallel to the mined experimentally.
neutral axis at a distance a = β 1c from the fiber of
maximum compressive strain. In the 1976 supplement to the 1971 Code, a lower limit of β1
equal to 0.65 was adopted for concrete strengths greater than
10.2.7.2 — Distance from the fiber of maximum 55 MPa. Research data from tests with high-strength
strain to the neutral axis, c, shall be measured in a concretes10.1,10.2 supported the equivalent rectangular stress
direction perpendicular to the neutral axis. block for concrete strengths exceeding 55 MPa, with a β1
CODE COMMENTARY
10.2.7.3 — For fc′ between 17 and 28 MPa, β 1 shall equal to 0.65. Use of the equivalent rectangular stress distri-
be taken as 0.85. For fc′ above 28 MPa, β 1 shall be bution specified in the 1971 Code, with no lower limit on β1 ,
reduced linearly at a rate of 0.05 for each 7 MPa of resulted in inconsistent designs for high-strength concrete for
strength in excess of 28 MPa, but β 1 shall not be taken members subject to combined flexure and axial load.
less than 0.65.
The equivalent rectangular stress distribution does not
represent the actual stress distribution in the compression
zone at ultimate, but does provide essentially the same
results as those obtained in tests.10.3
10.3 — General principles and requirements R10.3 — General principles and requirements
10.3.1 — Design of cross sections subject to flexure or R10.3.1 — Design strength equations for members subject
axial loads, or to combined flexure and axial loads, to flexure or combined flexure and axial load are derived in
shall be based on stress and strain compatibility using the paper, “Rectangular Concrete Stress Distribution in
assumptions in 10.2. Ultimate Strength Design.”10.3 Reference 10.3 and previous
editions of this Commentary also give the derivations of
strength equations for cross sections other than rectangular. 10
10.3.2 — Balanced strain conditions exist at a cross R10.3.2 — A balanced strain condition exists at a cross
section when tension reinforcement reaches the strain section when the maximum strain at the extreme compression
corresponding to fy just as concrete in compression fiber just reaches 0.003 simultaneously with the first yield
reaches its assumed ultimate strain of 0.003. strain fy /Es in the tension reinforcement. The reinforcement
ratio ρb, which produces balanced strain conditions under
flexure, depends on the shape of the cross section and the
location of the reinforcement.
10.3.3 — Sections are compression-controlled if the R10.3.3 — The nominal flexural strength of a member is
net tensile strain in the extreme tension steel, εt , is reached when the strain in the extreme compression fiber
equal to or less than the compression-controlled strain reaches the assumed strain limit 0.003. The net tensile strain
limit when the concrete in compression reaches its εt is the tensile strain in the extreme tension steel at nominal
assumed strain limit of 0.003. The compression- strength, exclusive of strains due to prestress, creep,
controlled strain limit is the net tensile strain in the shrinkage, and temperature. The net tensile strain in the
reinforcement at balanced strain conditions. For extreme tension steel is determined from a linear strain
Grade 420 reinforcement, and for all prestressed distribution at nominal strength, shown in Fig. R10.3.3,
reinforcement, it shall be permitted to set the using similar triangles.
compression-controlled strain limit equal to 0.002.
CODE COMMENTARY
When the net tensile strain in the extreme tension steel is
sufficiently large (equal to or greater than 0.005), the section
is defined as tension-controlled where ample warning of
failure with excessive deflection and cracking may be
expected. When the net tensile strain in the extreme tension
steel is small (less than or equal to the compression-
controlled strain limit), a brittle failure condition may be
expected, with little warning of impending failure. Flexural
members are usually tension-controlled, whereas compression
members are usually compression-controlled. Some sections,
such as those with small axial load and large bending moment,
will have net tensile strain in the extreme tension steel between
the above limits. These sections are in a transition region
between compression- and tension-controlled sections.
Section 9.3.2 specifies the appropriate strength reduction
factors for tension-controlled and compression-controlled
sections, and for intermediate cases in the transition region.
10
Before the development of these provisions, the limiting
tensile strain for flexural members was not stated, but was
implicit in the maximum tension reinforcement ratio that
was given as a fraction of ρb, which was dependent on the
yield strength of the reinforcement. The net tensile strain
limit of 0.005 for tension-controlled sections was chosen to
be a single value that applies to all types of steel
(prestressed and nonprestressed) permitted by this Code.
10.3.5 — For nonprestressed flexural members and R10.3.5 — The effect of this limitation is to restrict the
nonprestressed members with factored axial compres- reinforcement ratio in nonprestressed beams to about the
sive load less than 0.10fc′ Ag , εt at nominal strength same ratio as in editions of the Code before 2002. The
shall not be less than 0.004. reinforcement limit of 0.75ρb results in a net tensile strain
in extreme tension steel at nominal strength of 0.00376. The
limit of 0.004 is slightly more conservative. This limitation
does not apply to prestressed members.
CODE COMMENTARY
10.3.5.1 — Use of compression reinforcement shall
be permitted in conjunction with additional tension
reinforcement to increase the strength of flexural
members.
10.3.6 — Design axial strength φPn of compression R10.3.6 and R10.3.7 — The minimum design eccentricities
members shall not be taken greater than φPn,max , included in the 1963 and 1971 Codes were deleted from the
computed by Eq. (10-1) or (10-2). 1977 Code except for consideration of slenderness effects in
compression members with small or zero computed end
10.3.6.1 — For nonprestressed members with spiral moments (see 10.10.6.5). The specified minimum eccentricities
reinforcement conforming to 7.10.4 or composite were originally intended to serve as a means of reducing the
members conforming to 10.13: axial load design strength of a section in pure compression
to account for accidental eccentricities not considered in the
φPn,max = 0.85φ [0.85fc′ (Ag – Ast ) + fy Ast ] (10-1) analysis that may exist in a compression member, and to
recognize that concrete strength may be less than fc′ under
10.3.6.2 — For nonprestressed members with tie sustained high loads. The primary purpose of the minimum
reinforcement conforming to 7.10.5: eccentricity requirement was to limit the maximum design
axial strength of a compression member. This is now 10
φPn,max = 0.80φ [0.85fc′ (Ag – Ast ) + fy Ast ] (10-2) accomplished directly in 10.3.6 by limiting the design axial
strength of a section in pure compression to 85 or 80 percent
10.3.6.3 — For prestressed members, design axial of the nominal strength. These percentage values approximate
strength, φPn , shall not be taken greater than 0.85 (for the axial strengths at eccentricity-to-depth ratios of 0.05 and
members with spiral reinforcement) or 0.80 (for 0.10, specified in the earlier Codes for the spirally reinforced
members with tie reinforcement) of the design axial and tied members, respectively. The same axial load limita-
strength at zero eccentricity, φPo . tion applies to both cast-in-place and precast compression
members. Design aids and computer programs based on the
10.3.7 — Members subject to compressive axial load minimum eccentricity requirement of the 1963 and 1971
shall be designed for the maximum moment that can Codes are equally applicable.
accompany the axial load. The factored axial force Pu at
given eccentricity shall not exceed that given in 10.3.6. For prestressed members, the design axial strength in pure
The maximum factored moment Mu shall be magnified compression is computed by the strength design methods of
for slenderness effects in accordance with 10.10. Chapter 10, including the effect of the prestressing force.
1 1 1 1
-------- = --------- + --------- – -----
-
P ni P nx P ny P o
CODE COMMENTARY
where:
Pni = nominal axial load strength at given eccentricity
along both axes
Po = nominal axial load strength at zero eccentricity
Pnx = nominal axial load strength at given eccentricity
along x-axis
Pny = nominal axial load strength at given eccentricity
along y-axis
This relationship is most suitable when values Pnx and Pny
are greater than the balanced axial force Pb for the particular
axis.
10.4 — Distance between lateral supports R10.4 — Distance between lateral supports
of flexural members of flexural members
10.4.1 — Spacing of lateral supports for a beam shall Tests10.10,10.11 have shown that laterally unbraced reinforced
not exceed 50 times b, the least width of compression concrete beams of any reasonable dimensions, even when
10
flange or face. very deep and narrow, will not fail prematurely by lateral
buckling provided the beams are loaded without lateral
10.4.2 — Effects of lateral eccentricity of load shall be eccentricity that causes torsion.
taken into account in determining spacing of lateral
supports. Laterally unbraced beams are frequently loaded off center
(lateral eccentricity) or with slight inclination. Stresses and
deformations set up by such loading become detrimental for
narrow, deep beams, the more so as the unsupported length
increases. Lateral supports spaced closer than 50b may be
required by loading conditions.
10.5.1 — At every section of a flexural member where The provision for a minimum amount of reinforcement
tensile reinforcement is required by analysis, except as applies to flexural members, which for architectural or other
provided in 10.5.2, 10.5.3, and 10.5.4, As provided reasons, are larger in cross section than required for
shall not be less than that given by strength. With a very small amount of tensile reinforcement,
the computed moment strength as a reinforced concrete
0.25 f c′ section using cracked section analysis becomes less than
A s, min = ----------------------b wd (10-3) that of the corresponding unreinforced concrete section
fy computed from its modulus of rupture. Failure in such a
case can be sudden.
and not less than 1.4bwd/fy .
To prevent such a failure, a minimum amount of tensile
10.5.2 — For statically determinate members with a reinforcement is required by 10.5.1 in both positive and
flange in tension, As,min shall not be less than the negative moment regions. When concrete strength higher
value given by Eq. (10-3), except that bw is replaced than about 35 MPa is used, the 1.4/fy value previously
by either 2bw or the width of the flange, whichever is prescribed may not be sufficient. Equation (10-3) gives the
smaller. same amount of reinforcement as 1.4bw d/fy when fc′ equals
31 MPa. When the flange of a section is in tension, the
amount of tensile reinforcement needed to make the strength
of the reinforced section equal that of the unreinforced section
is about twice that for a rectangular section or that of a flanged
section with the flange in compression. A higher amount of
minimum tensile reinforcement is particularly necessary in
cantilevers and other statically determinate members where
there is no possibility for redistribution of moments.
CODE COMMENTARY
10.5.3 — The requirements of 10.5.1 and 10.5.2 need R10.5.3 — The minimum reinforcement required by Eq. (10-3)
not be applied if, at every section, As provided is at is to be provided wherever reinforcement is needed, except
least one-third greater than that required by analysis. where such reinforcement is at least one-third greater than
that required by analysis. This exception provides sufficient
additional reinforcement in large members where the
amount required by 10.5.1 or 10.5.2 would be excessive.
10.5.4 — For structural slabs and footings of uniform R10.5.4 — The minimum reinforcement required for slabs
thickness, As,min in the direction of the span shall be should be equal to the same amount as that required by
the same as that required by 7.12.2.1. Maximum 7.12.2.1 for shrinkage and temperature reinforcement.
spacing of this reinforcement shall not exceed three
times the thickness, nor 450 mm. Slabs-on-ground are not considered to be structural slabs in
the context of this section, unless they transmit vertical
loads or lateral forces from other parts of the structure to the
soil. Reinforcement, if any, in slabs-on-ground should be
proportioned with due consideration of all design forces.
Mat foundations and other slabs that help support the structure
vertically should meet the requirements of this section. 10
10.6.1 — This section prescribes rules for distribution R10.6.1 — Many structures designed by working stress
of flexural reinforcement to control flexural cracking in methods and with low steel stress served their intended
beams and in one-way slabs (slabs reinforced to resist functions with very limited flexural cracking. When high-
flexural stresses in only one direction). strength reinforcing steels are used at high service load
stresses, however, visible cracks should be expected, and
steps should be taken in detailing of the reinforcement to
control cracking. For reasons of durability and appearance,
many fine cracks are preferable to a few wide cracks.
CODE COMMENTARY
10.6.2 — Distribution of flexural reinforcement in two-
way slabs shall be as required by 13.3.
10.6.3 — Flexural tension reinforcement shall be well R10.6.3 — Several bars at moderate spacing are much more
distributed within maximum flexural tension zones of a effective in controlling cracking than one or two larger bars
member cross section as required by 10.6.4. of equivalent area.
10.6.4 — The spacing of reinforcement closest to the R10.6.4 — This section was updated in the 2005 edition to
tension face, s, shall not exceed that given by reflect the higher service stresses that occur in flexural
reinforcement with the use of the load combinations
introduced in the 2002 Code. The maximum bar spacing is
s = 380 ⎛ ----------⎞ – 2.5c c
280 (10-4)
⎝ f ⎠ specified directly to control cracking.10.15-10.17 For the usual
s
case of beams with Grade 420 reinforcement and 50 mm clear
cover to the main reinforcement, with fs = 280 MPa, the
but not greater than 300(280/fs ), where cc is the least
maximum bar spacing is 250 mm.
distance from surface of reinforcement or prestressing
steel to the tension face. If there is only one bar or wire
Crack widths in structures are highly variable. In Codes
10 nearest to the extreme tension face, s used in Eq. (10-4)
before the 1999 edition, provisions were given for distribution
is the width of the extreme tension face.
of reinforcement that were based on empirical equations
using a calculated maximum crack width of 0.4 mm. The
Calculated stress fs in reinforcement closest to the
current provisions for spacing are intended to limit surface
tension face at service load shall be computed based
cracks to a width that is generally acceptable in practice but
on the unfactored moment. It shall be permitted to take
may vary widely in a given structure.
fs as 2/3fy .
The role of cracks in the corrosion of reinforcement is
controversial. Research10.18,10.19 shows that corrosion is not
clearly correlated with surface crack widths in the range
normally found with reinforcement stresses at service load
levels. For this reason, the former distinction between interior
and exterior exposure has been eliminated.
10.6.5 — Provisions of 10.6.4 are not sufficient for R10.6.5 — Although a number of studies have been
structures subject to very aggressive exposure or conducted, clear experimental evidence is not available
designed to be watertight. For such structures, special regarding the crack width beyond which a corrosion danger
investigations and precautions are required. exists. Exposure tests indicate that concrete quality, adequate
compaction, and ample concrete cover may be of greater
importance for corrosion protection than crack width at the
concrete surface.
10.6.6 — Where flanges of T-beam construction are in R10.6.6 — In major T-beams, distribution of the negative
tension, part of the flexural tension reinforcement shall reinforcement for control of cracking should take into
be distributed over an effective flange width as defined account two considerations: (1) wide spacing of the reinforce-
in 8.12, or a width equal to one-tenth the span, which- ment across the full effective width of flange may cause
ever is smaller. If the effective flange width exceeds some wide cracks to form in the slab near the web, and (2)
one-tenth the span, some longitudinal reinforcement close spacing near the web leaves the outer regions of the
shall be provided in the outer portions of the flange. flange unprotected. The one-tenth limitation is to guard
against too wide a spacing, with some additional reinforce-
ment required to protect the outer portions of the flange.
10.6.7 — Where h of a beam or joist exceeds 900 mm, R10.6.7 — For relatively deep flexural members, some
longitudinal skin reinforcement shall be uniformly reinforcement should be placed near the vertical faces of the
distributed along both side faces of the member. Skin tension zone to control cracking in the web.10.20,10.21 (See
reinforcement shall extend for a distance h/2 from the Fig. R10.6.7.) Without such auxiliary steel, the width of the
tension face. The spacing s shall be as provided in cracks in the web may exceed the crack widths at the level
10.6.4, where cc is the least distance from the surface of the flexural tension reinforcement. This section was
CODE COMMENTARY
10
Fig. R10.6.7—Skin reinforcement for beams and joists with h > 900 mm.
of the skin reinforcement or prestressing steel to the modified in the 2005 edition to make the skin reinforcement
side face. It shall be permitted to include such reinforce- spacing consistent with that of the flexural reinforcement.
ment in strength computations if a strain compatibility The size of the skin reinforcement is not specified; research
analysis is made to determine stress in the individual has indicated that the spacing rather than bar size is of
bars or wires. primary importance.10.21 Bar sizes No. 10 to No. 16 (or
welded wire reinforcement with a minimum area of 210 mm2
per meter of depth) are typically provided.
10.7.1 — Deep beams are members loaded on one The span-to-depth ratios used to define deep beams in the
face and supported on the opposite face so that 1999 and earlier Codes were based on papers published in
compression struts can develop between the loads 1946 and 1953. The definitions of deep beams given in
and the supports, and have either: 10.7.1 and 11.8.1 of these earlier Codes were different from
each other and different from the current Code definition
(a) clear spans, ln , equal to or less than four times that is based on D-region behavior (see Appendix A). The
the overall member depth; or definitions of deep beams in Sections 10.7.1 and 11.8.1 are
consistent with each other and different from the definition
(b) regions with concentrated loads within twice the introduced in 2002, which is based on D-region behavior
member depth from the face of the support. (see Appendix A). Since 2002, the definitions of deep
Deep beams shall be designed either taking into beams in Sections 10.7.1 and 11.8.1 are consistent with
account nonlinear distribution of strain, or by Appendix A. each other.
(See also 11.7.1 and 12.10.6.) Lateral buckling shall
be considered. This Code does not contain detailed requirements for
designing deep beams for flexure except that nonlinearity of
10.7.2 — Vn of deep beams shall be in accordance strain distribution and lateral buckling is to be considered.
with 11.7. Suggestions for the design of deep beams for flexure are
given in References 10.22, 10.23, and 10.24.
10.7.3 — Minimum area of flexural tension reinforce-
ment, As,min , shall conform to 10.5.
CODE COMMENTARY
10.7.4 — Minimum horizontal and vertical reinforce-
ment in the side faces of deep beams shall satisfy
either A.3.3 or 11.7.4 and 11.7.5.
10.8 — Design dimensions for compression R10.8 — Design dimensions for compression
members members
10.8.1 — Isolated compression member with With the 1971 Code, minimum sizes for compression
multiple spirals members were eliminated to allow wider utilization of
reinforced concrete compression members in smaller size
Outer limits of the effective cross section of a and lightly loaded structures, such as low-rise residential
compression member with two or more interlocking and light office buildings. When small sections are used,
spirals shall be taken at a distance outside the there is a greater need for careful workmanship and
extreme limits of the spirals equal to the minimum shrinkage stresses have increased significance.
concrete cover required by 7.7.
10.8.2 — Compression member built R10.8.2, R10.8.3, and R10.8.4 — For column design,10.25
10
monolithically with wall the Code provisions for quantity of reinforcement, both
vertical and spiral, are based on the gross column area and
Outer limits of the effective cross section of a spirally core area, and the design strength of the column is based on
reinforced or tied reinforced compression member built the gross area of the column section. In some cases,
monolithically with a concrete wall or pier shall be however, the gross area is larger than necessary to carry the
taken not greater than 40 mm outside the spiral or tie factored load. The basis of 10.8.2, 10.8.3, and 10.8.4 is that
reinforcement. it is satisfactory to design a column of sufficient size to
carry the factored load and then simply add concrete around
10.8.3 — Equivalent circular compression member the designed section without increasing the reinforcement to
meet the minimum percentages required by 10.9.1. The
As an alternative to using the full gross area for design additional concrete should not be considered as carrying
of a compression member with a square, octagonal, or load; however, the effects of the additional concrete on
other shaped cross section, it shall be permitted to use member stiffness should be included in the structural analysis.
a circular section with a diameter equal to the least The effects of the additional concrete also should be
lateral dimension of the actual shape. Gross area considered in design of the other parts of the structure that
considered, required percentage of reinforcement, and interact with the oversize member.
design strength shall be based on that circular section.
10.9.1 — Area of longitudinal reinforcement, Ast , for R10.9.1 — This section prescribes the limits on the amount
noncomposite compression members shall be not less of longitudinal reinforcement for noncomposite compression
than 0.01Ag or more than 0.08Ag . members. If the use of high reinforcement ratios would
involve practical difficulties in the placing of concrete, a
lower percentage and hence a larger column, or higher
strength concrete or reinforcement (see R9.4) should be
CODE COMMENTARY
considered. The percentage of reinforcement in columns
should usually not exceed 4 percent if the column bars are
required to be lap spliced.
10.9.2 — Minimum number of longitudinal bars in R10.9.2 — For compression members, a minimum of four
compression members shall be 4 for bars within longitudinal bars are required when bars are enclosed by
rectangular or circular ties, 3 for bars within triangular rectangular or circular ties. For other shapes, one bar should
ties, and 6 for bars enclosed by spirals conforming to be provided at each apex or corner and proper lateral reinforce-
10.9.3. ment provided. For example, tied triangular columns require
three longitudinal bars, one at each apex of the triangular
ties. For bars enclosed by spirals, six bars are required.
CODE COMMENTARY
strength of eccentrically loaded columns and should be
considered in design.
10.9.3 — Volumetric spiral reinforcement ratio, ρs , R10.9.3 — The effect of spiral reinforcement in increasing
shall be not less than the value given by the load-carrying strength of the concrete within the core is
not realized until the column has been subjected to a load
Ag f c′ and deformation sufficient to cause the concrete shell
ρ s = 0.45 ⎛ ---------
- – 1⎞ ------ (10-5) outside the core to spall off. The amount of spiral reinforce-
⎝A ⎠f
ch yt
ment required by Eq. (10-5) is intended to provide additional
load-carrying strength for concentrically loaded columns
where the value of fyt used in Eq. (10-5) shall not equal to or slightly greater than the strength lost when the
exceed 700 MPa. For fyt greater than 420 MPa, lap shell spalls off. This principle was recommended by ACI
splices according to 7.10.4.5(a) shall not be used. Committee 10510.26 and has been a part of the Code since
1936. The derivation of Eq. (10-5) is given in the ACI
Committee 105 report. Tests and experience show that
columns containing the amount of spiral reinforcement
required by this section exhibit considerable toughness and
10 ductility. Research10.27-10.29 has indicated that 700 MPa
yield strength reinforcement can be used for confinement.
For the 2005 Code, the limit in yield strength for spiral
reinforcement was increased from 420 to 700 MPa.
10.10.1 — Slenderness effects shall be permitted to R10.10.1 — Second-order effects in many structures are
be neglected in the following cases: negligible. In these cases, it is not necessary to consider
slenderness effects and compression members can be
(a) for compression members not braced against designed based on forces determined from first-order analyses.
sidesway when: Slenderness effects can be neglected in both braced and
unbraced systems depending on the klu /r of the member. In
kl u evaluation of unbraced systems, moments are based on first-
-------- ≤ 22 (10-6) order elastic analysis.
r
The primary design aid to estimate the effective length
(b) for compression members braced against side-
factor k is the Jackson and Moreland Alignment Charts
sway when:
(Fig. R10.10.1.1), which allow a graphical determination of
k for a column of constant cross section in a multibay
kl u frame.10.4,10.30
-------- ≤ 34 – 12(M1 /M2) ≤ 40 (10-7)
r
Equation (10-7) is based on Eq. (10-11) assuming that a
where M1 /M2 is positive if the column is bent in single 5 percent increase in moments due to slenderness is accept-
curvature, and negative if the member is bent in able.10.31 As a first approximation, k may be taken equal to
double curvature. 1.0 in Eq. (10-7).
It shall be permitted to consider compression The Commentary used to state that a compression member
members braced against sidesway when bracing may be assumed braced if located in a story in which the
elements have a total stiffness, resisting lateral move- bracing elements have a total stiffness, resisting lateral
ment of that story, of at least 12 times the gross stiff- movement of the story, at least six times the sum of the stiff-
ness of the columns within the story. nesses of all the columns in the story. In ACI 318-95, the
CODE COMMENTARY
10
10.10.1.1 — The unsupported length of a compression language was changed to: “… the bracing elements have
member, lu , shall be taken as the clear distance such substantial lateral stiffness to resist the lateral deflections
between floor slabs, beams, or other members of the story that any resulting lateral deflection is not large
capable of providing lateral support in the direction enough to affect the column strength substantially.” The
being considered. Where column capitals or haunches change was made because of some concern that the
are present, lu shall be measured to the lower extremity multiplier of six might not be conservative enough. For the
of the capital or haunch in the plane considered. 2008 Code, a more conservative multiplier of 12 was
chosen. The stiffness of the lateral bracing is considered
10.10.1.2 — It shall be permitted to take the radius based on the principal directions of the framing system.
of gyration, r, equal to 0.30 times the overall dimension Bracing elements in typical building structures consist of
in the direction stability is being considered for rect- shear walls or lateral braces. Torsional eccentricity of the
angular compression members and 0.25 times the structural system can increase second-order effects and
diameter for circular compression members. For other should be considered.
shapes, it shall be permitted to compute r for the gross
concrete section.
CODE COMMENTARY
10.10.2 — When slenderness effects are not R10.10.2 — Design may be based on a nonlinear second-
neglected as permitted by 10.10.1, the design of order analysis, an elastic second-order analysis, or the
compression members, restraining beams, and other moment magnifier approach.10.31-10.33 The structure that is
supporting members shall be based on the factored analyzed should have members similar to those in the final
forces and moments from a second-order analysis structure. If the members in the final structure have cross-
satisfying 10.10.3, 10.10.4, or 10.10.5. These sectional dimensions more than 10 percent different from
members shall also satisfy 10.10.2.1 and 10.10.2.2. those assumed in the analysis, new member properties
The dimensions of each member cross section used in should be computed and the analysis repeated.
the analysis shall be within 10 percent of the dimensions
of the members shown on the design drawings or the
analysis shall be repeated.
10.10.2.1 — Total moment including second-order R10.10.2.1 — If the weight of a structure is high in
effects in compression members, restraining beams, proportion to its lateral stiffness, excessive PΔ effects
or other structural members shall not exceed 1.4 times (where secondary moments are more than 25 percent of the
the moment due to first-order effects. primary moments) may result, which will eventually
introduce singularities into the solution to the equations of
10 equilibrium, indicating physical structural instability.10.34
Analytical research10.35 on reinforced concrete frames
showed that the probability of stability failure increases
rapidly when the stability index Q exceeds 0.2, which is
equivalent to a secondary-to-primary moment ratio of 1.25.
According to ASCE/SEI 7-05,10.36 the maximum value of
the stability coefficient θ, which is close to the ACI stability
coefficient Q, is 0.25. This value is equivalent to a
secondary-to-primary moment ratio of 1.33. The upper limit
of 1.4 on the secondary-to-primary moment ratio was
chosen considering the above. By providing an upper limit
on the second-order moment, it is unnecessary to retain the
stability check given in 10.13.6 of the 2005 Code.
10.10.2.2 — Second-order effects shall be considered R10.10.2.2 — The maximum moment in a compression
along the length of compression members. It shall be member may occur between its ends. While second-order
permitted to account for these effects using the computer analysis programs may be used to evaluate magni-
moment magnification procedure outlined in 10.10.6. fication of the end moments, magnification between the
ends may not be accounted for unless the member is subdi-
vided along its length. The magnification may be evaluated
using the procedure outlined in 10.10.6.
Second-order analysis shall consider material The nonlinear second-order analysis procedure should have
nonlinearity, member curvature and lateral drift, duration been shown to predict ultimate loads within 15 percent of
of loads, shrinkage and creep, and interaction with the those reported in tests of indeterminate reinforced concrete
supporting foundation. The analysis procedure shall structures. At the very least, the comparison should include
have been shown to result in prediction of strength in tests of columns in planar nonsway frames, sway frames,
substantial agreement with results of comprehensive and frames with varying column stiffnesses. To allow for
tests of columns in statically indeterminate reinforced variability in the actual member properties and in the analysis,
concrete structures. the member properties used in analysis should be multiplied
by a stiffness reduction factor φK less than 1. The concept of
a stiffness reduction factor φK is discussed in R10.10.4. For
consistency with the second-order analysis in 10.10.4, the
stiffness reduction factor φK can be taken as 0.80.
CODE COMMENTARY
10.10.4 — Elastic second-order analysis R10.10.4 — Elastic second-order analysis
Elastic second-order analysis shall consider section The stiffnesses EI used in an analysis for strength design
properties determined taking into account the influ- should represent the stiffnesses of the members immediately
ence of axial loads, the presence of cracked regions prior to failure. This is particularly true for a second-order
along the length of the member, and the effects of load analysis that should predict the lateral deflections at loads
duration. approaching ultimate. The EI values should not be based
totally on the moment-curvature relationship for the most
highly loaded section along the length of each member.
Instead, they should correspond to the moment-end rotation
relationship for a complete member.
10.10.4.1 — It shall be permitted to use the following R10.10.4.1 — The values of Ec , I, and A have been
properties for the members in the structure: chosen from the results of frame tests and analyses and
include an allowance for the variability of the computed
(a) Modulus of elasticity ...................... Ec from 8.5.1 deflections. The modulus of elasticity of the concrete, Ec , is
(b) Moments of inertia, I based on the specified concrete compressive strength while
Compression members: the sway deflections are a function of the average concrete
Columns.................................................... 0.70Ig strength, which is higher. The moments of inertia are taken
Walls—Uncracked..................................... 0.70Ig from Reference 10.35, which are multiplied by the stiffness
—Cracked ........................................ 0.35Ig reduction factor φK = 0.875. For example, the moment of
Flexural members: inertia for columns is 0.875(0.80Ig) = 0.70Ig. These two
Beams....................................................... 0.35Ig effects result in an overestimation of the second-order
Flat plates and flat slabs ........................... 0.25Ig deflections on the order of 20 to 25 percent, corresponding
(c) Area ........................................................... 1.0Ag to an implicit stiffness reduction of 0.80 to 0.85 on the
stability calculation.
Alternatively, the moments of inertia of compression
and flexural members, I, shall be permitted to be The moment of inertia of T-beams should be based on the
computed as follows: effective flange width defined in 8.12. It is generally suffi-
Compression members: ciently accurate to take Ig of a T-beam as two times the Ig
for the web, 2(bwh3/12).
A st⎞ ⎛ Mu P
I = ⎛ 0.80 + 25 -------- - – 0.5 ------u⎞⎠ I g ≤ 0.875I g
1 – ---------- (10-8) If the factored moments and shears from an analysis based
⎝ Ag ⎠ ⎝ P h Po
u
on the moment of inertia of a wall, taken equal to 0.70Ig,
indicate that the wall will crack in flexure, based on the
where Pu and Mu shall be determined from the
modulus of rupture, the analysis should be repeated with I =
particular load combination under consideration, or
0.35Ig in those stories where cracking is predicted using
the combination of Pu and Mu determined in the
factored loads.
smallest value of I. I need not be taken less than
0.35Ig .
The values of the moments of inertia were derived for
Flexural members: nonprestressed members. For prestressed members, the
moments of inertia may differ depending on the amount,
b w⎞ location, and type of the reinforcement and the degree of
I = ( 0.10 + 25ρ ) ⎛ 1.2 – 0.2 ------
- I ≤ 0.5I g (10-9) cracking prior to ultimate. The stiffness values for
⎝ d⎠ g prestressed concrete members should include an allowance
for the variability of the stiffnesses.
CODE COMMENTARY
For continuous flexural members, I shall be permitted to Section 10.10 provides requirements for strength and
be taken as the average of values obtained from assumes frame analyses will be carried out using factored
Eq. (10-9) for the critical positive and negative moment loads. Analyses of deflections, vibrations, and building
sections. I need not be taken less than 0.25Ig . periods are needed at various service (unfactored) load
levels10.37,10.38 to determine the serviceability of the structure
The cross-sectional dimensions and reinforcement ratio and to estimate the wind forces in wind tunnel laboratories.
used in the above formulas shall be within 10 percent of The moments of inertia of the structural members in the
the dimensions and reinforcement ratio shown on the service load analyses should be representative of the degree
design drawings or the stiffness evaluation shall be of cracking at the various service load levels investigated.
repeated. Unless a more accurate estimate of the degree of cracking at
service load level is available, it is satisfactory to use
1.0/0.70 = 1.43 times the moments of inertia given here for
service load analyses.
10.10.4.2 — When sustained lateral loads are R10.10.4.2 — The unusual case of sustained lateral loads
present, I for compression members shall be divided might exist, for example, if there were permanent lateral
by (1 + βds ). The term βds shall be taken as the ratio of loads resulting from unequal earth pressures on two sides of
maximum factored sustained shear within a story to a building.
the maximum factored shear in that story associated
with the same load combination, but shall not be taken
greater than 1.0.
Columns and stories in structures shall be designated This section describes an approximate design procedure that
as nonsway or sway columns or stories. The design of uses the moment magnifier concept to account for slenderness
columns in nonsway frames or stories shall be based effects. Moments computed using an ordinary first-order
on 10.10.6. The design of columns in sway frames or frame analysis are multiplied by a moment magnifier that is
stories shall be based on 10.10.7. a function of the factored axial load Pu and the critical buckling
load Pc for the column. Nonsway and sway frames are
10.10.5.1 — It shall be permitted to assume a column treated separately. A first-order frame analysis is an elastic
in a structure is nonsway if the increase in column end analysis that does not include the internal force effects
moments due to second-order effects does not exceed resulting from deflections.
5 percent of the first-order end moments.
The moment magnifier design method requires the designer
10.10.5.2 — It also shall be permitted to assume a to distinguish between nonsway frames, which are designed
story within a structure is nonsway if: according to 10.10.6, and sway frames, which are designed
according to 10.10.7. Frequently this can be done by inspection
ΣP u Δ o by comparing the total lateral stiffness of the columns in a
- ≤ 0.05
Q = ----------------- (10-10) story to that of the bracing elements. A compression
V us l c
member may be assumed nonsway by inspection if it is
located in a story in which the bracing elements (shear
where ΣPu and Vus are the total factored vertical load walls, shear trusses, or other types of lateral bracing) have
and the horizontal story shear, respectively, in the such substantial lateral stiffness to resist the lateral deflections
story being evaluated, and Δo is the first-order relative of the story that any resulting lateral deflection is not large
lateral deflection between the top and the bottom of enough to affect the column strength substantially. If not
that story due to Vus .
ACI 318 Building Code and Commentary
CHAPTER 10 145
CODE COMMENTARY
readily apparent by inspection, 10.10.5.1 and 10.10.5.2 give
two possible ways of doing this. In 10.10.5.1, a story in a
frame is said to be nonsway if the increase in the lateral load
moments resulting from PΔ effects does not exceed 5 percent
of the first-order moments.10.35 Section 10.10.5.2 gives an
alternative method of determining this based on the stability
index for a story Q. In computing Q, ΣPu should correspond
to the lateral loading case for which ΣPu is greatest. A
frame may contain both nonsway and sway stories. This test
would not be suitable if Vus is zero.
Compression members shall be designed for factored The φ-factors used in the design of slender columns represent
axial force Pu and the factored moment amplified for two different sources of variability. First, the stiffness
the effects of member curvature Mc where reduction φK-factor accounts for the variability in the
stiffness EI and the moment magnification analysis.
Mc = δns M2 (10-11) Second, the strength reduction φ-factor for tied and spiral
columns accounts for the variability of the strength of the
where cross section. Studies reported in Reference 10.41 indicate
that the stiffness reduction factor φK and the cross-sectional
Cm strength reduction φ-factors do not have the same values.
δ ns = ---------------------------
- ≥ 1.0 (10-12) These studies suggest the stiffness reduction factor φK for an
Pu isolated column should be 0.75 for both tied and spiral
1 – ------------------
0.75P c columns. The 0.75 factor in Eq. (10-12) is the stiffness
reduction factor φK. The factor is based on the probability of
and understrength of a single isolated slender column. In the
case of a multistory frame, the column and frame deflections
2 depend on the average concrete strength, which is higher
π EI than the strength of the concrete in the critical single
P c = ---------------- (10-13)
2
( kl u ) understrength column. For this reason, the value of φK in
10.10.4 is 0.875.
10.10.6.1 — EI shall be taken as R10.10.6.1 — In defining the critical load, the main
problem is the choice of a stiffness EI that reasonably
( 0.2E c I g + E s I se ) approximates the variations in stiffness due to cracking,
EI = ----------------------------------------------
- (10-14) creep, and nonlinearity of the concrete stress-strain curve.
1 + β dns
Either Eq. (10-14) or (10-15) may be used to compute EI.
Equation (10-14) was derived for small eccentricity ratios
or and high levels of axial load where slenderness effects are
most pronounced. Equation (10-15) is a simplified approxi-
0.4E c I g mation to Eq. (10-14) and is less accurate.10.42 For
EI = ---------------------
- (10-15)
1 + β dns improved accuracy, EI can be approximated using the
suggested E and I values provided by Eq. (10-8) divided by
(1 + βdns).
Alternatively, EI shall be permitted to be computed using
the value of I from Eq. (10-8) divided by (1 + βdns ).
CODE COMMENTARY
10.10.6.2 — The term βdns shall be taken as the ratio R10.10.6.2 — Creep due to sustained load will increase
of maximum factored axial sustained load to maximum the lateral deflections of a column and hence the moment
factored axial load associated with the same load magnification. This is approximated for design by reducing
combination, but shall not be taken greater than 1.0. the stiffness EI used to compute Pc and hence δ by dividing
EI by (1 + β dns). Both the concrete and steel terms in
Eq. (10-14) are divided by (1 + βdns) to reflect the premature
yielding of steel in columns subjected to sustained load. For
simplification, it can be assumed that βdns = 0.6. In this
case, Eq. (10-15) becomes
EI = 0.25EcIg
10.10.6.3 — The effective length factor, k, shall be R10.10.6.3 — The effective length factor for a compression
permitted to be taken as 1.0. member considering braced behavior ranges from 0.5 and
1.0. While lower values can be justified, it is recommended
that a k value of 1.0 be used. If lower values are used, the
calculation of k should be based on analysis of the frame
10 using Ec and I values given in 10.10.4. The Jackson and
Moreland Alignment Charts (Fig. R10.10.1.1) can be used
to estimate lower values of k.10.4,10.30
10.10.6.4 — For members without transverse loads R10.10.6.4 — The factor Cm is a correction factor
between supports, Cm shall be taken as relating the actual moment diagram to an equivalent
uniform moment diagram. The derivation of the moment
M magnifier assumes that the maximum moment is at or near
C m = 0.6 + 0.4 -------1 (10-16) midheight of the column. If the maximum moment occurs at
M2
one end of the column, design should be based on an
equivalent uniform moment Cm M2 that would lead to the
where M1/M2 is positive if the column is bent in single same maximum moment when magnified.10.31
curvature, and negative if the member is bent in
double curvature. For members with transverse loads In the case of compression members that are subjected to
between supports, Cm shall be taken as 1.0. transverse loading between supports, it is possible that the
maximum moment will occur at a section away from the
end of the member. If this occurs, the value of the largest
calculated moment occurring anywhere along the member
should be used for the value of M2 in Eq. (10-11). Cm is to
be taken as 1.0 for this case.
10.10.6.5 — Factored moment, M2, in Eq. (10-11) R10.10.6.5 — In the Code, slenderness is accounted for
shall not be taken less than by magnifying the column end moments. If the factored
column moments are very small or zero, the design of
M2,min = Pu (0.6 + 0.03h) (10-17) slender columns should be based on the minimum eccentricity
given in this section. It is not intended that the minimum
about each axis separately, where 0.6 and h are in eccentricity be applied about both axes simultaneously.
inches. For members in which M2,min exceeds M2, the
value of Cm in Eq. (10-16) shall either be taken equal The factored column end moments from the structural analysis
to 1.0, or shall be based on the ratio of the computed are used in Eq. (10-16) in determining the ratio M1/M2 for
end moments, M1/M2. the column when the design should be based on minimum
eccentricity. This eliminates what would otherwise be a
discontinuity between columns with computed eccentricities
less than the minimum eccentricity and columns with
computed eccentricities equal to or greater than the
minimum eccentricity.
CODE COMMENTARY
10.10.7 — Moment magnification procedure — Sway R10.10.7 — Moment magnification procedure — Sway
Moments M1 and M2 at the ends of an individual The analysis described in this section deals only with plane
compression member shall be taken as frames subjected to loads causing deflections in that plane.
If torsional displacements are significant, a three-dimen-
M1 = M1ns + δsM1s (10-18) sional second-order analysis should be used.
10.10.7.1 — Flexural members shall be designed for R10.10.7.1 — The strength of a sway frame is governed
the total magnified end moments of the compression by the stability of the columns and by the degree of end
members at the joint. restraint provided by the beams in the frame. If plastic
hinges form in the restraining beam, the structure
approaches a failure mechanism and its axial load capacity
is drastically reduced. This section provides that the
10
designer make certain that the restraining flexural members
have the strength to resist the magnified column moments.
10.10.7.3 — The moment magnifier δs shall be R10.10.7.3 — The iterative PΔ analysis for second-order
calculated as moments can be represented by an infinite series. The solution
of this series is given by Eq. (10-20).10.35 Reference 10.43
1 shows that Eq. (10-20) closely predicts the second-order
δ s = -------------- ≥ 1 (10-20)
1–Q moments in a sway frame until δs exceeds 1.5.
If δs calculated by Eq. (10-20) exceeds 1.5, δs shall be The PΔ moment diagrams for deflected columns are curved,
calculated using second-order elastic analysis or with Δ related to the deflected shape of the columns.
10.10.7.4. Equation (10-20) and most commercially available second-
order frame analyses have been derived assuming that the
PΔ moments result from equal and opposite forces of PΔ/lc
applied at the bottom and top of the story. These forces give
a straight line PΔ moment diagram. The curved PΔ moment
diagrams lead to lateral displacements on the order of 15
percent larger than those from the straight line PΔ moment
diagrams. This effect can be included in Eq. (10-20) by
writing the denominator as (1 – 1.15Q) rather than (1 – Q).
The 1.15 factor has been left out of Eq. (10-20) for simplicity.
CODE COMMENTARY
are established using Eq. (10-20), selection of the cross
sections of the columns involves the strength reduction
factors φ from 9.3.2.2.
10.10.7.4 — Alternatively, it shall be permitted to R10.10.7.4 — To check the effects of story stability, δs is
calculate δs as computed as an averaged value for the entire story based on
use of ΣPu /ΣPc . This reflects the interaction of all sway-
1 resisting columns in the story in the PΔ effects since the
δ s = -------------------------------- ≥ 1 (10-21)
ΣP u lateral deflection of all columns in the story should be equal
1 – ---------------------- in the absence of torsional displacements about a vertical
0.75ΣP c
axis. In addition, it is possible that a particularly slender
individual column in a sway frame could have substantial
where ΣPu is the summation for all the factored midheight deflections even if adequately braced against
vertical loads in a story and ΣPc is the summation for lateral end deflections by other columns in the story. Such a
all sway-resisting columns in a story. Pc is calculated column should be checked using 10.10.6.
using Eq. (10-13) with k determined from 10.10.7.2
and EI from 10.10.6.1. If the lateral load deflections involve a significant torsional
10 displacement, the moment magnification in the columns
farthest from the center of twist may be underestimated by
the moment magnifier procedure. In such cases, a three-
dimensional second-order analysis should be considered.
If fc′ of a column is greater than 1.4 times that of the The requirements of this section are based on the effect of
floor system, transmission of load through the floor floor concrete strength on column strength.10.44 The provisions
system shall be provided by 10.12.1, 10.12.2, or mean that where the column concrete strength does not
10.12.3. exceed the floor concrete strength by more than 40 percent, no
special precautions need be taken. For higher column
concrete strengths, methods in 10.12.1 or 10.12.2 should be
used for corner or edge columns. Methods in 10.12.1,
10.12.2, or 10.12.3 should be used for interior columns with
adequate restraint on all four sides.
ACI 318 Building Code and Commentary
CHAPTER 10 149
CODE COMMENTARY
10.12.1 — Concrete of strength specified for the R10.12.1 — Application of the concrete placement procedure
column shall be placed in the floor at the column location. described in 10.12.1 requires the placing of two different
Top surface of the column concrete shall extend 2 ft concrete mixtures in the floor system. The lower-strength
into the slab from face of column. Column concrete mixture should be placed while the higher-strength concrete
shall be well integrated with floor concrete, and shall is still plastic and should be adequately vibrated to ensure
be placed in accordance with 6.4.6 and 6.4.7. the concretes are well integrated. This requires careful coordi-
nation of the concrete deliveries and the possible use of
retarders. In some cases, additional inspection services will
be required when this procedure is used. It is important that
the higher-strength concrete in the floor in the region of the
column be placed before the lower-strength concrete in the
remainder of the floor to prevent accidental placing of the
low-strength concrete in the column area. It is the responsi-
bility of the licensed design professional to indicate on the
drawings where the high- and low-strength concretes are to
be placed.
10.12.3 — For columns laterally supported on four R10.12.3 — Research10.45 has shown that heavily loaded
sides by beams of approximately equal depth or by slabs do not provide as much confinement as lightly loaded
slabs, it shall be permitted to base strength of the slabs when ratios of column concrete strength to slab
column on an assumed concrete strength in the concrete strength exceed about 2.5. Consequently, a limit is
column joint equal to 75 percent of column concrete placed on the concrete strength ratio assumed in design.
strength plus 35 percent of floor concrete strength. In
the application of 10.12.3, the ratio of column concrete
strength to slab concrete strength shall not be taken
greater than 2.5 for design.
10.13.1 — Composite compression members shall R10.13.1 — Composite columns are defined without reference
include all such members reinforced longitudinally with to classifications of combination, composite, or concrete-
structural steel shapes, pipe, or tubing with or without filled pipe column. Reference to other metals used for
longitudinal bars. reinforcement has been omitted because they are seldom
used in concrete construction.
10.13.2 — Strength of a composite member shall be R10.13.2 — The same rules used for computing the load-
computed for the same limiting conditions applicable moment interaction strength for reinforced concrete sections
to ordinary reinforced concrete members. can be applied to composite sections. Interaction charts for
concrete-filled tubing would have a form identical to those
of the ACI Design Handbook10.4 but with γ slightly greater
than 1.0.
CODE COMMENTARY
10.13.3 — Any axial load strength assigned to concrete R10.13.3 and R10.13.4 — Direct bearing or direct connection
of a composite member shall be transferred to the for transfer of forces between steel and concrete can be
concrete by members or brackets in direct bearing on developed through lugs, plates, or reinforcing bars welded
the composite member concrete. to the structural shape or tubing before the concrete is cast.
Flexural compressive stress need not be considered a part of
10.13.4 — All axial load strength not assigned to direct compression load to be developed by bearing. A
concrete of a composite member shall be developed concrete encasement around a structural steel shape may
by direct connection to the structural steel shape, pipe, stiffen the shape, but it would not necessarily increase its
or tube. strength.
10.13.5 — For evaluation of slenderness effects, R10.13.5 — Equation (10-22) is given because the rules of
radius of gyration, r, of a composite section shall be 10.10.1.2 for estimating the radius of gyration are overly
not greater than the value given by conservative for concrete-filled tubing and are not appli-
cable for members with enclosed structural shapes.
( E c I g /5 ) + E s I sx
r = ------------------------------------------------
- (10-22) In reinforced concrete columns subject to sustained loads,
( E c A g /5 ) + E s A sx creep transfers some of the load from the concrete to the
10 steel, increasing the steel stresses. In the case of lightly
and, as an alternative to a more accurate calculation, reinforced columns, this load transfer may cause the
EI in Eq. (10-13) shall be taken either as Eq. (10-14) or compression steel to yield prematurely, resulting in a loss in
the effective EI. Accordingly, both the concrete and steel
( E c I g /5 ) terms in Eq. (10-14) are reduced to account for creep. For
EI = ---------------------
- + E s I sx (10-23) heavily reinforced columns or for composite columns in
1 + βd
which the pipe or structural shape makes up a large
percentage of the cross section, the load transfer due to creep is
not significant. Accordingly, Eq. (10-23) was revised in the
1980 Code supplement so that only the EI of the concrete is
reduced for sustained load effects.
10.13.6 — Structural steel encased concrete core R10.13.6 — Structural steel-encased concrete core
10.13.6.1 — For a composite member with a Steel-encased concrete sections should have a metal wall
concrete core encased by structural steel, the thick- thickness large enough to attain longitudinal yield stress
ness of the steel encasement shall be not less than before buckling outward.
fy
- for each face of width b
b ---------
3E s
nor
fy
- for circular sections of diameter h
b ---------
8E s
10.13.7 — Spiral reinforcement around structural R10.13.7 — Spiral reinforcement around structural
steel core steel core
A composite member with spirally reinforced concrete Concrete that is laterally confined by a spiral has increased
around a structural steel core shall conform to strength, and the size of the spiral required can be regulated
10.13.7.1 through 10.13.7.4. on the basis of the strength of the concrete outside the
CODE COMMENTARY
10.13.7.1 — Design yield strength of structural steel spiral—the same reasoning that applies for columns reinforced
core shall be the specified minimum yield strength for only with longitudinal bars. The radial pressure provided by
the grade of structural steel used but not to exceed the spiral ensures interaction between concrete, reinforcing
350 MPa. bars, and steel core such that longitudinal bars will both
stiffen and strengthen the cross section.
10.13.7.2 — Spiral reinforcement shall conform to
10.9.3.
10.13.8 — Tie reinforcement around structural R10.13.8 — Tie reinforcement around structural
steel core steel core 10
A composite member with laterally tied concrete The yield strength of the steel core should be limited to that
around a structural steel core shall conform to which exists at strains below those that can be sustained
10.13.8.1 through 10.13.8.7. without spalling of the concrete. It has been assumed that
axially compressed concrete will not spall at strains less
10.13.8.1 — Design yield strength of structural steel than 0.0018. The yield strength of 0.0018 × 200,000, or
core shall be the specified minimum yield strength for 360 MPa, represents an upper limit of the useful maximum
the grade of structural steel used but not to exceed steel stress.
350 MPa.
Research10.46 has shown that the required amount of tie
10.13.8.2 — Lateral ties shall extend completely reinforcement around the structural steel core is sufficient
around the structural steel core. for the longitudinal steel bars to be included in the flexural
stiffness of the composite column.
10.13.8.3 — Lateral ties shall have a diameter not
less than 0.02 times the greatest side dimension of
composite member, except that ties shall not be
smaller than No. 10 and are not required to be larger
than No. 16. Welded wire reinforcement of equivalent
area shall be permitted.
CODE COMMENTARY
10.14 — Bearing strength R10.14 — Bearing strength
10.14.1 — Design bearing strength of concrete shall R10.14.1 — This section deals with bearing strength of
not exceed φ(0.85fc′ A1), except when the supporting concrete supports. The permissible bearing stress of 0.85fc′ is
surface is wider on all sides than the loaded area, then based on tests reported in Reference 10.47. (See also 15.8).
the design bearing strength of the loaded area shall be
permitted to be multiplied by A 2 /A 1 but by not more When the supporting area is wider than the loaded area on
than 2. all sides, the surrounding concrete confines the bearing area,
resulting in an increase in bearing strength. No minimum
depth is given for a supporting member. The minimum
depth of support will be controlled by the shear require-
ments of 11.11.
10.14.2 — Section 10.14 does not apply to post- R10.14.2 — Post-tensioning anchorages are usually laterally
tensioning anchorages. reinforced, in accordance with 18.13.
CODE COMMENTARY
10
10
CODE COMMENTARY
11.1 — Shear strength R11.1 — Shear strength
11.1.1 — Except for members designed in accordance This chapter includes shear and torsion provisions for both
with Appendix A, design of cross sections subject to nonprestressed and prestressed concrete members. The
shear shall be based on shear-friction concept (11.6) is particularly applicable to
design of reinforcement details in precast structures. Provisions
φVn ≥ Vu (11-1) are included for deep flexural members (11.7), brackets and
corbels (11.8), and shear walls (11.9). Shear provisions for
where Vu is the factored shear force at the section slabs and footings are given in 11.11.
considered and Vn is nominal shear strength
computed by The shear strength is based on an average shear stress on the
full effective cross section bw d. In a member without shear
Vn = Vc + Vs (11-2) reinforcement, shear is assumed to be carried by the
concrete web. In a member with shear reinforcement, a
where Vc is nominal shear strength provided by portion of the shear strength is assumed to be provided by 11
concrete calculated in accordance with 11.2, 11.3, or the concrete and the remainder by the shear reinforcement.
11.11, and Vs is nominal shear strength provided by The shear strength provided by concrete Vc is assumed to be the
shear reinforcement calculated in accordance with same for beams with and without shear reinforcement and is
11.4, 11.9.9, or 11.11. taken as the shear causing significant inclined cracking. These
assumptions are discussed in References 11.1, 11.2, and 11.3.
11.1.1.2 — In determining Vc , whenever applicable, R11.1.1.2 — In a member of variable depth, the internal
effects of axial tension due to creep and shrinkage in shear at any section is increased or decreased by the vertical
restrained members shall be considered and effects of component of the inclined flexural stresses. Computation
inclined flexural compression in variable depth methods are outlined in various textbooks and in the 1940
members shall be permitted to be included. Joint Committee Report.11.6
11.1.2 — The values of f c′ used in this chapter shall R11.1.2 — Because of a lack of test data and practical
not exceed 8.3 MPa except as allowed in 11.1.2.1. experience with concretes having compressive strengths
greater than 70 MPa, the 1989 edition of the Code imposed
a maximum value of 8.3 MPa on f c′ for use in the calcula-
tion of shear strength of concrete beams, joists, and slabs.
Exceptions to this limit were permitted in beams and joists
when the transverse reinforcement satisfied an increased
value for the minimum amount of web reinforcement. There
are limited test data on the two-way shear strength of high-
strength concrete slabs. Until more experience is obtained for
two-way slabs built with concretes that have strengths
greater than 70 MPa, it is prudent to limit f c′ to 8.3 MPa
for the calculation of shear strength.
CODE COMMENTARY
11.1.2.1 — Values of f c ′ greater than 8.3 MPa shall R11.1.2.1 — Based on the test results in References 11.7,
be permitted in computing Vc , Vci , and Vcw for reinforced 11.8, 11.9, 11.10, and 11.11, an increase in the minimum
or prestressed concrete beams and concrete joist amount of transverse reinforcement is required for high-
construction having minimum web reinforcement in strength concrete. These tests indicated a reduction in the
accordance with 11.4.6.3, 11.4.6.4, or 11.5.5.2. reserve shear strength as fc′ increased in beams reinforced
with the specified minimum amount of transverse reinforce-
ment, which is equivalent to an effective shear stress of
4.2 MPa. A provision introduced in the 1989 edition of the
Code required an increase in the minimum amount of
transverse reinforcement for concrete strengths between
70 and 105 MPa. This provision, which led to a sudden
increase in the minimum amount of transverse reinforcement
at a compressive strength of 70 MPa, has been replaced by a
gradual increase in the minimum Av as fc′ increases, as given
by Eq. (11-13).
11.1.3.1 — For nonprestressed members, sections R11.1.3.1 — The closest inclined crack to the support of
located less than a distance d from face of support the beam in Fig. R11.1.3.1(a) will extend upward from the
shall be permitted to be designed for Vu computed at a face of the support reaching the compression zone about d
distance d. from the face of the support. If loads are applied to the top of
this beam, the stirrups across this crack are stressed by loads
acting on the lower freebody in Fig. R11.1.3.1(a). The loads
applied to the beam between the face of the column and the
point d away from the face are transferred directly to the
support by compression in the web above the crack.
Accordingly, the Code permits design for a maximum
factored shear force Vu at a distance d from the support for
nonprestressed members, and at a distance h/2 for
prestressed members. Two things are emphasized: first,
stirrups are required across the potential crack designed for the
shear at d from the support, and second, a tension force exists
in the longitudinal reinforcement at the face of the support.
CODE COMMENTARY
CODE COMMENTARY
members supported by bearing at the bottom of the
member, such as shown in Fig. R11.1.3.1(c); and (2)
members framing monolithically into another member as
illustrated in Fig. R11.1.3.1(d).
11.1.3.2 — For prestressed members, sections R11.1.3.2 — Because d frequently varies in prestressed
located less than a distance h /2 from face of support members, the location of the critical section has arbitrarily
shall be permitted to be designed for Vu computed at a been taken as h/2 from the face of the support.
distance h /2.
11.2 — Shear strength provided by concrete R11.2 — Shear strength provided by concrete
for nonprestressed members for nonprestressed members
11.2.1.2 — For members subject to axial compression, R11.2.1.2 and R11.2.1.3 — See R11.2.2.2.
Nu ⎞
V c = 0.17 ⎛ 1 + -------------
- λ f c ′b w d (11-4)
⎝ 14A g⎠
CODE COMMENTARY
11.2.1.3 — For members subject to significant axial
tension, Vc shall be taken as zero unless a more
detailed analysis is made using 11.2.2.3.
11.2.2.1 — For members subject to shear and R11.2.2.1 — Equation (11-5) is the basic expression for
flexure only, shear strength of members without shear reinforcement.11.3
The three variables in Eq. (11-5), λ f c′ (as a measure of
V u d⎞ concrete tensile strength), ρw, and Vu d/Mu , are known to
V c = ⎛ 0.16λ f c ′ + 17ρ w ----------
- b d (11-5) affect shear strength, although some research data11.1,11.12
⎝ Mu ⎠ w
indicate that Eq. (11-5) overestimates the influence of fc′ and
underestimates the influence of ρw and Vud/Mu . Further
but not greater than 0.29λ f c′ bwd. When computing information11.13 has indicated that shear strength decreases
Vc by Eq. (11-5), Vud /Mu shall not be taken greater as the overall depth of the member increases.
than 1.0, where Mu occurs simultaneously with Vu at
section considered. The minimum value of Mu equal to Vud in Eq. (11-5) is to
limit Vc near points of inflection.
11
For most designs, it is convenient to assume that the second
term of Eq. (11-5) equals 0.01 f c′ and use Vc equal to
0.17λ f c′ bwd as permitted in 11.2.1.1.
11.2.2.2 — For members subject to axial compression, R11.2.2.2 — Equations (11-6) and (11-7), for members
it shall be permitted to compute Vc using Eq. (11-5) subject to axial compression in addition to shear and flexure,
with Mm substituted for Mu and Vud /Mu not then are derived in the Joint ACI-ASCE Committee 326 report.11.3
limited to 1.0, where As Nu is increased, the value of Vc computed from Eq. (11-5)
and (11-6) will exceed the upper limit given by Eq. (11-7)
( 4h – d ) before the value of Mm given by Eq. (11-6) becomes negative.
M m = M u – N u --------------------- (11-6) The value of Vc obtained from Eq. (11-5) has no physical
8
significance if a negative value of Mm is substituted. For this
However, Vc shall not be taken greater than condition, Eq. (11-7) or Eq. (11-4) should be used to
calculate Vc . Values of Vc for members subject to shear and
axial load are illustrated in Fig. R11.2.2.2. The background
0.29N for these equations is discussed and comparisons are made
V c = 0.29λ f c ′b w d 1 + ------------------u- (11-7)
Ag with test data in Reference 11.2.
Nu /Ag shall be expressed in MPa. When Mm as Because of the complexity of Eq. (11-5) and (11-6), an
computed by Eq. (11-6) is negative, Vc shall be alternative design provision, Eq. (11-4), is permitted.
computed by Eq. (11-7).
CODE COMMENTARY
11.2.2.3 — For members subject to significant axial R11.2.2.3 — Equation (11-8) may be used to compute Vc
tension, for members subject to significant axial tension. Shear
reinforcement may then be designed for Vn – Vc. The term
0.29N “significant” is used to recognize judgment is required in
V c = 0.17 ⎛ 1 + ------------------u-⎞ λ f c ′b w d (11-8) deciding whether axial tension needs to be considered. Low
⎝ A ⎠
g levels of axial tension often occur due to volume changes,
but are not important in structures with adequate expansion
but not less than zero, where Nu is negative for joints and minimum reinforcement. It may be desirable to
tension. Nu /Ag shall be expressed in MPa. design shear reinforcement to carry total shear if there is
uncertainty about the magnitude of axial tension.
11.2.3 — For circular members, the area used to R11.2.3 — Shear tests of members with circular sections
compute Vc shall be taken as the product of the diameter indicate that the effective area can be taken as the gross area of
and effective depth of the concrete section. It shall be the section or as an equivalent rectangular area.11.1,11.14,11.15
permitted to take d as 0.80 times the diameter of the
concrete section.
11.3.2 — For members with effective prestress force R11.3.2 — Equation (11-9) offers a simple means of
not less than 40 percent of the tensile strength of flexural computing Vc for prestressed concrete beams.11.2 It may be
reinforcement, unless a more detailed calculation is applied to beams having prestressed reinforcement only, or
made in accordance with 11.3.3, to members reinforced with a combination of prestressed
reinforcement and nonprestressed deformed bars. Equation
V u d p⎞ (11-9) is most applicable to members subject to uniform
V c = ⎛ 0.05λ f c′ + 4.8 -------------
- b d (11-9) loading and may give conservative results when applied to
⎝ M ⎠ w u composite girders for bridges.
but Vc need not be taken less than 0.17λ f c′ bwd. Vc In applying Eq. (11-9) to simply supported members subject
shall not be taken greater than 0.42λ f c′ bwd or the to uniform loads, Vu dp /Mu can be expressed as
value given in 11.3.4 or 11.3.5. Vu d p /Mu shall not be
taken greater than 1.0, where Mu occurs simulta- Vu dp d p ( l – 2x )
neously with Vu at the section considered. ------------ = ------------------------
-
Mu x(l – x)
11.3.3 — Vc shall be permitted to be computed in R11.3.3 — Two types of inclined cracking occur in
accordance with 11.3.3.1 and 11.3.3.2, where Vc shall concrete beams: web-shear cracking and flexure-shear
be the lesser of Vci and Vcw. cracking. These two types of inclined cracking are illustrated
in Fig. R11.3.3.
CODE COMMENTARY
11.3.3.1 — Vci shall be computed by
V i M cre
V ci = 0.05λ f c′ b w d p + V d + ------------------
- (11-10)
M max
V i M cre
V = ------------------
-
M max
CODE COMMENTARY
plus an additional increment of shear required to change the
flexural crack to a flexure-shear crack. The externally
applied factored loads, from which Vi and Mmax are deter-
mined, include superimposed dead load, earth pressure, and
live load. In computing Mcre for substitution into Eq. (11-10), I
and γt are the properties of the section resisting the externally
applied loads.
Vi = Vu – Vd
11
Mmax = Mu – Md
V u M ct
V ci = 0.05λ f c′ b w d + ---------------
-
Mu
where
CODE COMMENTARY
Equation (11-12) is based on the assumption that web-shear
cracking occurs due to the shear causing a principal tensile
stress of approximately 0.33λ f c′ at the centroidal axis of
the cross section. Vp is calculated from the effective
prestress force without load factors.
11.3.4 — In a pretensioned member in which the R11.3.4 and R11.3.5 — The effect of the reduced prestress
section at a distance h/2 from face of support is closer near the ends of pretensioned beams on the shear strength
to the end of member than the transfer length of the should be taken into account. Section 11.3.4 relates to the
prestressing steel, the reduced prestress shall be shear strength at sections within the transfer length of
considered when computing Vcw . This value of Vcw prestressing steel when bonding of prestressing steel
shall also be taken as the maximum limit for Eq. (11-9). extends to the end of the member.
The prestress force shall be assumed to vary linearly
from zero at end of the prestressing steel, to a Section 11.3.5 relates to the shear strength at sections within
maximum at a distance from end of the prestressing the length over which some of the prestressing steel is not
steel equal to the transfer length, assumed to be 50 bonded to the concrete, or within the transfer length of the
diameters for strand and 100 diameters for single wire. prestressing steel for which bonding does not extend to the
end of the beam.
11.3.5 — In a pretensioned member where bonding of
some tendons does not extend to the end of member, 11
a reduced prestress shall be considered when
computing Vc in accordance with 11.3.2 or 11.3.3. The
value of Vcw calculated using the reduced prestress
shall also be taken as the maximum limit for Eq. (11-9).
The prestress force due to tendons for which bonding
does not extend to the end of member shall be
assumed to vary linearly from zero at the point at which
bonding commences to a maximum at a distance from
this point equal to the transfer length, assumed to be 50
diameters for strand and 100 diameters for single wire.
11.4 — Shear strength provided by shear R11.4 — Shear strength provided by shear
reinforcement reinforcement
CODE COMMENTARY
(c) Combinations of stirrups and bent longitudinal
reinforcement.
11.4.2 — The values of fy and fyt used in design of R11.4.2 — Limiting the values of fy and fyt used in design of
shear reinforcement shall not exceed 420 MPa, except shear reinforcement to 420 MPa provides a control on
the value shall not exceed 550 MPa for welded diagonal crack width. In the 1995 Code, the limitation of
deformed wire reinforcement. 420 MPa for shear reinforcement was raised to 550 MPa for
welded deformed wire reinforcement. Research11.18-11.20 has
indicated that the performance of higher-strength steels as
shear reinforcement has been satisfactory. In particular,
full-scale beam tests described in Reference 11.19 indicated
that the widths of inclined shear cracks at service load levels
were less for beams reinforced with smaller-diameter
welded deformed wire reinforcement cages designed on the
basis of a yield strength of 520 MPa than beams reinforced
with deformed Grade 420 stirrups.
11.4.3 — Where the provisions of 11.4 are applied to R11.4.3 — Although the value of d may vary along the span
prestressed members, d shall be taken as the of a prestressed beam, studies11.2 have shown that, for
11 distance from extreme compression fiber to centroid of prestressed concrete members, d need not be taken less than
the prestressed and nonprestressed longitudinal 0.80h. The beams considered had some straight tendons or
tension reinforcement, if any, but need not be taken reinforcing bars at the bottom of the section and had stirrups
less than 0.80h. that enclosed the steel.
11.4.4 — Stirrups and other bars or wires used as R11.4.4 — It is essential that shear (and torsion) reinforcement
shear reinforcement shall extend to a distance d from be adequately anchored at both ends to be fully effective on
extreme compression fiber and shall be developed at either side of any potential inclined crack. This generally
both ends according to 12.13. requires a hook or bend at the end of the reinforcement as
provided by 12.13.
11.4.6.1 — A minimum area of shear reinforcement, R11.4.6.1 — Shear reinforcement restrains the growth of
Av,min , shall be provided in all reinforced concrete inclined cracking. Ductility is increased and a warning of
flexural members (prestressed and nonprestressed) failure is provided. In an unreinforced web, the sudden
where Vu exceeds 0.5φVc , except in members satis- formation of inclined cracking might lead directly to failure
fying one or more of (a) through (f): without warning. Such reinforcement is of great value if a
member is subjected to an unexpected tensile force or an
(a) Footings and solid slabs; overload. Accordingly, a minimum area of shear reinforcement
CODE COMMENTARY
(b) Hollow-core units with total untopped depth not not less than that given by Eq. (11-13) or (11-14) is required
greater than 315 mm and hollow-core units where wherever Vu is greater than 0.5φVc. Solid slabs, footings and
Vu is not greater than 0.5φVcw ; joists are excluded from the minimum shear reinforcement
requirement because there is a possibility of load sharing
(c) Concrete joist construction defined by 8.13; between weak and strong areas. However, research11.21-11.23
(d) Beams with h not greater than 250 mm; has shown that deep, lightly reinforced one-way slabs and
beams, particularly if constructed with high-strength
(e) Beam integral with slabs with h not greater than concrete, or concrete having a small coarse aggregate size,
600 mm and not greater than the larger of 2.5 times may fail at shear loads less than Vc , calculated from Eq. (11-3)
thickness of flange, and 0.5 times width of web; especially if subjected to concentrated loads. Because of
this, the exclusion for certain beam types in 11.4.6.1(e) is
(f) Beams constructed of steel fiber-reinforced, restricted to cases in which h does not exceed 24 in. For
normalweight concrete with fc′ not exceeding 40 MPa, beams where fc′ is greater than 48 MPa, consideration should
h not greater than 600 mm, and Vu not greater than be given to providing minimum shear reinforcement when h
φ0.17 f c′ bwd. is greater than 450 mm and Vu is greater than 0.5φVc.
Even when Vu is less than 0.5φ Vc, the use of some web
reinforcement is recommended in all thin-web post-
tensioned prestressed concrete members (joists, waffle
slabs, beams, and T-beams) to reinforce against tensile 11
forces in webs resulting from local deviations from the
design tendon profile, and to provide a means of supporting
the tendons in the design profile during construction. If
sufficient support is not provided, lateral wobble and local
deviations from the smooth parabolic tendon profile
assumed in design may result during placement of the
concrete. In such cases, the deviations in the tendons tend to
straighten out when the tendons are stressed. This process
may impose large tensile stresses in webs, and severe
cracking may develop if no web reinforcement is provided.
Unintended curvature of the tendons, and the resulting
tensile stresses in webs, may be minimized by securely
tying tendons to stirrups that are rigidly held in place by
other elements of the reinforcing cage and held down in the
forms. The maximum spacing of stirrups used for this
purpose should not exceed the smaller of 1.5 h or 1.2 m.
When applicable, the shear reinforcement provisions of
11.4.5 and 11.4.6 will require closer stirrup spacings.
CODE COMMENTARY
R11.4.6.1(f) — This exception is intended to provide a
design alternative to the use of shear reinforcement, as
defined in 11.4.1.1, for members with longitudinal flexural
reinforcement in which Vu does not exceed φ 0.17 f c′ bwd.
Fiber-reinforced concrete beams with hooked or crimped
steel fibers in dosages as required by 5.6.6.2 have been
shown, through laboratory tests, to exhibit shear strengths
larger than 0.29 f c′ bwd.11.27 There are no data for the use
of steel fibers as shear reinforcement in concrete members
exposed to chlorides from deicing chemicals, salt, salt
water, brackish water, seawater, or spray from these sources.
Where steel fibers are used as shear reinforcement in
corrosive environments, corrosion protection should be
considered.
11.4.6.2 — Minimum shear reinforcement require- R11.4.6.2 — When a member is tested to demonstrate
ments of 11.4.6.1 shall be permitted to be waived if that its shear and flexural strengths are adequate, the actual
shown by test that required Mn and Vn can be devel- member dimensions and material strengths are known. The
oped when shear reinforcement is omitted. Such tests strength used as a basis for comparison should therefore be
11 shall simulate effects of differential settlement, creep, that corresponding to a strength reduction factor of unity (φ =
shrinkage, and temperature change, based on a real- 1.0), i.e. the required nominal strength Vn and Mn . This
istic assessment of such effects occurring in service. ensures that if the actual material strengths in the field were
less than specified, or the member dimensions were in error
such as to result in a reduced member strength, a satisfac-
tory margin of safety will be retained.
11.4.6.3 — Where shear reinforcement is required R11.4.6.3 — Previous versions of the Code have
by 11.4.6.1 or for strength and where 11.5.1 allows required a minimum area of transverse reinforcement that
torsion to be neglected, Av,min for prestressed (except is independent of concrete strength. Tests11.9 have indicated
as provided in 11.4.6.4) and nonprestressed members the need to increase the minimum area of shear reinforce-
shall be computed by ment as concrete strength increases to prevent sudden
shear failures when inclined cracking occurs. Equation
bw s (11-13) provides for a gradual increase in the minimum
A v, min = 0.062 f c ′ ----------
- (11-13) area of transverse reinforcement, while maintaining the
f yt
previous minimum value.
11.4.6.4 — For prestressed members with an effective R11.4.6.4 — Tests11.28 of prestressed beams with minimum
prestress force not less than 40 percent of the tensile web reinforcement based on Eq. (11-13) and (11-14) indicated
strength of the flexural reinforcement, Av,min shall not that the smaller Av from these two equations was sufficient
be less than the smaller value from Eq. (11-13) and to develop ductile behavior.
(11-14).
Equation (11-14) may be used only for prestressed members
A ps f pu s d meeting the minimum prestress force requirements given in
A v, min = ----------------------
- ------- (11-14) 11.4.6.4. This equation is discussed in Reference 11.28.
80f yt d b w
CODE COMMENTARY
11.4.7 — Design of shear reinforcement R11.4.7 — Design of shear reinforcement
11.4.7.1 — Where Vu exceeds φVc , shear reinforce- Design of shear reinforcement is based on a modified truss
ment shall be provided to satisfy Eq. (11-1) and (11-2), analogy. The truss analogy assumes that the total shear is
where Vs shall be computed in accordance with carried by shear reinforcement. However, considerable
11.4.7.2 through 11.4.7.9. research on both nonprestressed and prestressed members
has indicated that shear reinforcement needs to be designed
11.4.7.2 — Where shear reinforcement perpendicular to carry only the shear exceeding that which causes inclined
to axis of member is used, cracking, provided the diagonal members in the truss are
assumed to be inclined at 45 degrees.
A v f yt d
V s = -----------------
- (11-15) Equations (11-15), (11-16), and (11-17) are presented in
s
terms of nominal shear strength provided by shear reinforce-
ment Vs. When shear reinforcement perpendicular to axis of
where Av is the area of shear reinforcement within
member is used, the required area of shear reinforcement Av
spacing s.
and its spacing s are computed by
Av ( V u – φV c )
------ = --------------------------
-
s φf yt d 11
Research11.29,11.30 has shown that shear behavior of wide
beams with substantial flexural reinforcement is improved if
the transverse spacing of stirrup legs across the section is
reduced.
11.4.7.3 — Where circular ties, hoops, or spirals are R11.4.7.3 — Although the transverse reinforcement in a
used as shear reinforcement, Vs shall be computed circular section may not consist of straight legs, tests indicate
using Eq. (11-15) where d is defined in 11.2.3 for that Eq. (11-15) is conservative if d is taken as defined in
circular members, Av shall be taken as two times the 11.2.3.11.14,11.15
area of the bar in a circular tie, hoop, or spiral at a
spacing s, s is measured in a direction parallel to
longitudinal reinforcement, and fyt is the specified yield
strength of circular tie, hoop, or spiral reinforcement.
A v f yt ( sin α + cos α )d
V s = ---------------------------------------------------------
- (11-16)
s
CODE COMMENTARY
11.4.7.6 — Where shear reinforcement consists of
a series of parallel bent-up bars or groups of parallel
bent-up bars at different distances from the support,
Vs shall be computed by Eq. (11-16).
CODE COMMENTARY
of the member. In the thin-walled tube analogy, the resistance
is assumed to be provided by the outer skin of the cross
section roughly centered on the closed stirrups. Both hollow
and solid sections are idealized as thin-walled tubes both
before and after cracking.
It shall be permitted to neglect torsion effects if the Torques that do not exceed approximately one-quarter of the
factored torsional moment Tu is less than: cracking torque Tcr will not cause a structurally significant
reduction in either the flexural or shear strength and can be
(a) For nonprestressed members ignored. The cracking torsion under pure torsion Tcr is
derived by replacing the actual section with an equivalent
2
thin-walled tube with a wall thickness t prior to cracking of
⎛ A cp⎞ 0.75Acp /pcp and an area enclosed by the wall centerline Ao
φ0.083λ f c′ ⎜ ---------
-⎟
⎝ p cp ⎠ equal to 2Acp /3. Cracking is assumed to occur when the
principal tensile stress reaches 0.33λ f c′ . In a nonpre-
stressed beam loaded with torsion alone, the principal tensile
(b) For prestressed members stress is equal to the torsional shear stress, τ = T/(2Aot).
Thus, cracking occurs when τ reaches 0.33λ f c′ , giving
⎛ A cp⎞
2
f pc the cracking torque Tcr as
φ0.083λ f c′ ⎜ ---------
-⎟ 1 + --------------------------
⎝ p cp ⎠ 0.33λ f c ′
2
⎛ A cp⎞
(c) For nonprestressed members subjected to an T cr = 0.33λ f c′ ⎜ --------
-⎟
⎝ p cp ⎠
axial tensile or compressive force
2
For solid members, the interaction between the cracking
⎛ A cp⎞ Nu torsion and the inclined cracking shear is approximately
φ0.083λ f c′ ⎜ ---------
-⎟ 1 + ---------------------------------- circular or elliptical. For such a relationship, a torque of
⎝ p cp ⎠ 0.33A g λ f c ′
0.25Tcr , as used in 11.5.1, corresponds to a reduction of
CODE COMMENTARY
For members cast monolithically with a slab, the over- 3 percent in the inclined cracking shear. This reduction in the
hanging flange width used in computing Acp and pcp inclined cracking shear was considered negligible. The stress
shall conform to 13.2.4. For a hollow section, Ag shall at cracking 0.33λ f c′ has purposely been taken as a lower
be used in place of Acp in 11.5.1, and the outer bound value.
boundaries of the section shall conform to 13.2.4.
For prestressed members, the torsional cracking load is
11.5.1.1 — For isolated members with flanges and increased by the prestress. A Mohr’s Circle analysis based
for members cast monolithically with a slab, the over- on average stresses indicates the torque required to cause a
hanging flange width used to compute Acp and pcp principal tensile stress equal to 0.33λ f c′ is
shall conform to 13.2.4, except that the overhanging 1 + f pc ⁄ ( 0.33λ f c ′ ) times the corresponding torque in a
flanges shall be neglected in cases where the parameter nonprestressed beam. A similar modification is made in part
Acp2 /p (c) of 11.5.1 for members subjected to axial load and torsion.
cp calculated for a beam with flanges is less
than that computed for the same beam ignoring the
flanges. For torsion, a hollow member is defined as having one or
more longitudinal voids, such as a single-cell or multiple-cell
box girder. Small longitudinal voids, such as ungrouted post-
tensioning ducts that result in Ag /Acp greater than or equal to
0.95, can be ignored when computing the threshold torque in
11.5.1. The interaction between torsional cracking and shear
11 cracking for hollow sections is assumed to vary from the
elliptical relationship for members with small voids, to a
straight-line relationship for thin-walled sections with large
voids. For a straight-line interaction, a torque of 0.25Tcr
would cause a reduction in the inclined cracking shear of
about 25 percent. This reduction was judged to be excessive.
11.5.2 — Calculation of factored torsional moment R11.5.2 — Calculation of factored torsional moment
11.5.2.1 — If the factored torsional moment, Tu, in a R11.5.2.1 and R11.5.2.2 — In designing for torsion in
member is required to maintain equilibrium and reinforced concrete structures, two conditions may be
exceeds the minimum value given in 11.5.1, the identified:11.34,11.35
member shall be designed to carry Tu in accordance
with 11.5.3 through 11.5.6. (a) The torsional moment cannot be reduced by redistri-
bution of internal forces (11.5.2.1). This is referred to as
11.5.2.2 — In a statically indeterminate structure equilibrium torsion, since the torsional moment is
where reduction of the torsional moment in a member required for the structure to be in equilibrium.
can occur due to redistribution of internal forces upon
cracking, the maximum Tu shall be permitted to be For this condition, illustrated in Fig. R11.5.2.1, torsion
reduced to the values given in (a), (b), or (c), as applicable: reinforcement designed according to 11.5.3 through
11.5.6 must be provided to resist the total design torsional
(a) For nonprestressed members, at the sections moments.
described in 11.5.2.4
CODE COMMENTARY
2
⎛ A cp⎞
φ0.33λ f c′ ⎜ ---------
-⎟
⎝ p cp ⎠
2
⎛ A cp⎞ f pc
φ0.33λ f c′ ⎜ ---------
-⎟ 1 + --------------------------
⎝ p cp ⎠ 0.33λ f c′
CODE COMMENTARY
Section 11.5.2.2 applies to typical and regular framing
conditions. With layouts that impose significant torsional
rotations within a limited length of the member, such as a
heavy torque loading located close to a stiff column, or a
column that rotates in the reverse directions because of
other loading, a more exact analysis is advisable.
11.5.2.4 — In nonprestressed members, sections R11.5.2.4 and R11.5.2.5 — It is not uncommon for a
11 located less than a distance d from the face of a beam to frame into one side of a girder near the support of
support shall be designed for not less than Tu the girder. In such a case, a concentrated shear and torque
computed at a distance d. If a concentrated torque are applied to the girder.
occurs within this distance, the critical section for
design shall be at the face of the support.
11.5.3.1 — The cross-sectional dimensions shall be R11.5.3.1 — The size of a cross section is limited for two
such that: reasons: first, to reduce unsightly cracking, and second, to
prevent crushing of the surface concrete due to inclined
(a) For solid sections compressive stresses due to shear and torsion. In Eq. (11-18)
and (11-19), the two terms on the left-hand side are the
Vu ⎞ 2 ⎛ Tu ph ⎞ 2 Vc shear stresses due to shear and torsion. The sum of these
⎛ ---------- + ⎜ -------------------⎟ ≤ φ ⎛ ----------
- + 0.66 f c′ ⎞ (11-18)
⎝ b d-⎠ ⎝ b ⎠ stresses may not exceed the stress causing shear cracking
⎝ 1.7A ⎠ wd
2
w
oh plus 0.66 f c′ , similar to the limiting strength given in
11.4.7.9 for shear without torsion. The limit is expressed in
(b) For hollow sections terms of Vc to allow its use for nonprestressed or prestressed
concrete. It was originally derived on the basis of crack
control. It is not necessary to check against crushing of the
Vu ⎞ ⎛ Tu ph ⎞
⎛ ---------- Vc
- + ⎜ -------------------⎟ ≤ φ ⎛ ----------
- + 0.66 f c′ ⎞ (11-19) web because this happens at higher shear stresses.
⎝ b d⎠ ⎝ ⎝b d ⎠
1.7A ⎠
2
w w
oh
In a hollow section, the shear stresses due to shear and torsion
both occur in the walls of the box as shown in Fig. 11.5.3.1(a)
For prestressed members, d shall be determined in and hence are directly additive at point A as given in
accordance with 11.4.3. Eq. (11-19). In a solid section, the shear stresses due to
torsion act in the “tubular” outside section while the shear
stresses due to Vu are spread across the width of the section
as shown in Fig. R11.5.3.1(b). For this reason, stresses are
combined in Eq. (11-18) using the square root of the sum of
the squares rather than by direct addition.
CODE COMMENTARY
11
11.5.3.2 — If the wall thickness varies around the R11.5.3.2 — Generally, the maximum will be on the wall
perimeter of a hollow section, Eq. (11-19) shall be where the torsional and shearing stresses are additive [Point A
evaluated at the location where the left-hand side of in Fig. R11.5.3.1(a)]. If the top or bottom flanges are
Eq. (11-19) is a maximum. thinner than the vertical webs, it may be necessary to
evaluate Eq. (11-19) at points B and C in Fig. R11.5.3.1(a).
At these points, the stresses due to the shear force are
usually negligible.
Tu ⎞
⎛ ---------------------
⎝ 1.7A t ⎠
oh
11.5.3.4 — The values of fy and fyt used for R11.5.3.4 — Limiting the values of fy and fyt used in
design of torsional reinforcement shall not exceed design of torsion reinforcement to 420 MPa provides a
420 MPa. control on diagonal crack width.
11.5.3.5 — Where Tu exceeds the threshold torsion, R11.5.3.5 — The factored torsional resistance φTn must
design of the cross section shall be based on equal or exceed the torsion Tu due to the factored loads. In
the calculation of Tn, all the torque is assumed to be resisted
φTn ≥ Tu (11-20) by stirrups and longitudinal steel with Tc = 0. At the same
CODE COMMENTARY
time, the nominal shear strength provided by concrete, Vc ,
is assumed to be unchanged by the presence of torsion. For
beams with Vu greater than about 0.8φVc , the resulting
amount of combined shear and torsional reinforcement is
essentially the same as required by the 1989 Code. For
smaller values of Vu, more shear and torsion reinforcement
will be required.
11.5.3.6 — Tn shall be computed by R11.5.3.6 — Equation (11-21) is based on the space truss
analogy shown in Fig. R11.5.3.6(a) with compression diag-
2A o A t f yt onals at an angle θ, assuming the concrete carries no tension
T n = ------------------------ cot θ (11-21) and the reinforcement yields. After torsional cracking
s
develops, the torsional resistance is provided mainly by
closed stirrups, longitudinal bars, and compression diagonals.
where Ao shall be determined by analysis except that it
The concrete outside these stirrups is relatively ineffective.
shall be permitted to take Ao equal to 0.85Aoh ; θ shall
For this reason Ao , the gross area enclosed by the shear flow
not be taken smaller than 30 degrees nor larger than
path around the perimeter of the tube, is defined after
60 degrees. It shall be permitted to take θ equal to:
cracking in terms of Aoh , the area enclosed by the centerline
of the outermost closed transverse torsional reinforcement.
11 (a) 45 degrees for nonprestressed members or
The area Aoh is shown in Fig. R11.5.3.6(b) for various cross
members with less prestress than in (b); or
sections. In an I-, T-, or L-shaped section, Aoh is taken as that
(b) 37.5 degrees for prestressed members with an area enclosed by the outermost legs of interlocking stirrups as
effective prestress force not less than 40 percent of shown in Fig. R11.5.3.6(b). The expression for Ao given by
the tensile strength of the longitudinal reinforcement. Hsu11.36 may be used if greater accuracy is desired.
CODE COMMENTARY
in the individual sides of the tube or space truss, as shown in
Fig. R11.5.3.6(a).
11.5.3.7 — The additional area of longitudinal rein- R11.5.3.7 — Figure R11.5.3.6(a) shows the shear forces
forcement to resist torsion, Al , shall not be less than V1 to V4 resulting from the shear flow around the walls of the
tube. On a given wall of the tube, the shear flow Vi is resisted
A f yt⎞ by a diagonal compression component, Di = Vi /sinθ, in the
A l = ------t p h ⎛ ------
2
cot θ (11-22) concrete. An axial tension force, Ni = Vi (cotθ ), is needed
s ⎝f ⎠
y in the longitudinal steel to complete the resolution of Vi.
where θ shall be the same value used in Eq. (11-21) Figure R11.5.3.7 shows the diagonal compressive stresses and
and At /s shall be taken as the amount computed from the axial tension force, Ni , acting on a short segment along one
Eq. (11-21) not modified in accordance with 11.5.5.2 wall of the tube. Because the shear flow due to torsion is 11
or 11.5.5.3; fyt refers to closed transverse torsional constant at all points around the perimeter of the tube, the
reinforcement, and fy refers to longitudinal torsional resultants of Di and Ni act through the midheight of side i. As
reinforcement. a result, half of Ni can be assumed to be resisted by each of the
top and bottom chords as shown. Longitudinal reinforcement
with a strength Al fy should be provided to resist the sum of
the Ni forces, ΣNi , acting in all of the walls of the tube.
CODE COMMENTARY
11.5.3.8 — Reinforcement required for torsion shall R11.5.3.8 — The stirrup requirements for torsion and
be added to that required for the shear, moment, and shear are added and stirrups are provided to supply at least
axial force that act in combination with the torsion. The the total amount required. Since the stirrup area Av for shear
most restrictive requirements for reinforcement spacing is defined in terms of all the legs of a given stirrup while the
and placement shall be met. stirrup area At for torsion is defined in terms of one leg only,
the addition of stirrups is carried out as follows
Av + t A A
Total ⎛ -------------
-⎞ = -----v- + 2 -----t
⎝ s ⎠ s s
If a stirrup group had four legs for shear, only the legs adjacent
to the sides of the beam would be included in this summation
since the inner legs would be ineffective for torsion.
11.5.3.9 — It shall be permitted to reduce the area of R11.5.3.9 — The longitudinal tension due to torsion is
longitudinal torsion reinforcement in the flexural offset in part by the compression in the flexural compression
compression zone by an amount equal to Mu /(0.9df y ), zone, allowing a reduction in the longitudinal torsion steel
where Mu occurs at the section simultaneously with required in the compression zone.
Tu , except that the reinforcement provided shall not be
less than that required by 11.5.5.3 or 11.5.6.2.
(b) The spacing of the longitudinal reinforcement In a prestressed beam, the same technique (providing addi-
including tendons shall satisfy the requirements in tional reinforcing bars with capacity Al fy ) can be followed, or
11.5.6.2. overstrength of the prestressing steel can be used to resist
some of the axial force Al fy as outlined in the next paragraph.
CODE COMMENTARY
In a prestressed beam, the stress in the prestressing steel at
nominal strength will be between fse and fps. A portion of
the Al fy force can be resisted by a force of ApsΔfpt in the
prestressing steel, where Δfpt is the difference between the
stress which can be developed in the strand at the section
under consideration and the stress required to resist the bending
moment at this section, Mu. The stress required to resist the
bending moment can be calculated as [Mu /φ0.9dpAps)]. For
pretensioned strands, the stress which can be developed near
the free end of the strand can be calculated using the
procedure illustrated in Fig. R12.9. Note that near the ends
of a pretensioned member, the available stress in the
prestressing steel will need to be reduced to account for lack
of full development, and should be determined in conjunction
with 9.3.2.7.
11.5.4.1 — Torsion reinforcement shall consist of R11.5.4.1 — Both longitudinal and closed transverse
longitudinal bars or tendons and one or more of the reinforcement are required to resist the diagonal tension
following: stresses due to torsion. The stirrups must be closed, since
inclined cracking due to torsion may occur on all faces of a
(a) Closed stirrups or closed ties, perpendicular to member.
the axis of the member;
In the case of sections subjected primarily to torsion, the
(b) A closed cage of welded wire reinforcement with concrete side cover over the stirrups spalls off at high
transverse wires perpendicular to the axis of the torques.11.37 This renders lapped-spliced stirrups ineffec-
member; tive, leading to a premature torsional failure.11.38 In such
(c) In nonprestressed beams, spiral reinforcement. cases, closed stirrups should not be made up of pairs of
U-stirrups lapping one another.
11.5.4.2 — Transverse torsional reinforcement shall R11.5.4.2 — When a rectangular beam fails in torsion,
be anchored by one of the following: the corners of the beam tend to spall off due to the inclined
compressive stresses in the concrete diagonals of the
(a) A 135-degree standard hook, or seismic hook as space truss changing direction at the corner as shown in
defined in 2.2, around a longitudinal bar; Fig. R11.5.4.2(a). In tests,11.37 closed stirrups anchored
by 90-degree hooks failed when this occurred. For this
(b) According to 12.13.2.1, 12.13.2.2, or 12.13.2.3 in reason, 135-degree standard hooks or seismic hooks are
regions where the concrete surrounding the preferable for torsional stirrups in all cases. In regions
anchorage is restrained against spalling by a flange where this spalling is prevented by an adjacent slab or
or slab or similar member. flange, 11.5.4.2(b) relaxes this and allows 90-degree hooks
(see Fig. R11.5.4.2(b)).
CODE COMMENTARY
11
11.5.4.3 — Longitudinal torsion reinforcement shall R11.5.4.3 — If high torsion acts near the end of a beam,
be developed at both ends. the longitudinal torsion reinforcement should be adequately
anchored. Sufficient development length should be provided
outside the inner face of the support to develop the needed
tension force in the bars or tendons. In the case of bars, this
may require hooks or horizontal U-shaped bars lapped with
the longitudinal torsion reinforcement.
11.5.4.4 — For hollow sections in torsion, the R11.5.4.4 — The closed stirrups provided for torsion in a
distance from the centerline of the transverse torsional hollow section should be located in the outer half of the wall
reinforcement to the inside face of the wall of the thickness effective for torsion where the wall thickness can
hollow section shall not be less than 0.5Aoh /ph . be taken as Aoh /ph .
11.5.5.1 — A minimum area of torsional reinforce- R11.5.5.1 and R11.5.5.2 — If a member is subject to a
ment shall be provided in all regions where Tu exceeds factored torsional moment Tu greater than the values specified
the threshold torsion given in 11.5.1. in 11.5.1, the minimum amount of transverse web reinforce-
ment for combined shear and torsion is 0.35 bw s/fyt . The
11.5.5.2 — Where torsional reinforcement is differences in the definition of Av and the symbol At should
required by 11.5.5.1, the minimum area of transverse be noted; Av is the area of two legs of a closed stirrup
closed stirrups shall be computed by whereas At is the area of only one leg of a closed stirrup.
CODE COMMENTARY
for the minimum area of transverse closed stirrups has been
changed for consistency with calculations required for
minimum shear reinforcement.
11.5.5.3 — Where torsional reinforcement is R11.5.5.3 — Reinforced concrete beam specimens with
required by 11.5.5.1, the minimum total area of longi- less than 1 percent torsional reinforcement by volume have
tudinal torsional reinforcement, Al,min , shall be failed in pure torsion at torsional cracking.11.31 In the 1989
computed by and prior Codes, a relationship was presented that required
about 1 percent torsional reinforcement in beams loaded in
0.42 f c ′A cp ⎛ A t⎞ f yt pure torsion and less in beams with combined shear and
A l ,min = --------------------------------- – ------ p h ------ (11-24) torsion, as a function of the ratio of shear stresses due to
fy ⎝ s⎠ fy torsion and shear. Equation (11-24) was simplified by
assuming a single value of this reduction factor and results
where At /s shall not be taken less than 0.175bw /fyt ; in a volumetric ratio of about 0.5 percent.
fyt refers to closed transverse torsional reinforcement,
and fy refers to longitudinal reinforcement.
11.5.6.2 — The longitudinal reinforcement required R11.5.6.2 — In R11.5.3.7, it was shown that longitudinal
for torsion shall be distributed around the perimeter of reinforcement is needed to resist the sum of the longitudinal
the closed stirrups with a maximum spacing of 300 mm. tensile forces due to torsion in the walls of the thin-walled
The longitudinal bars or tendons shall be inside the tube. Since the force acts along the centroidal axis of the
stirrups. There shall be at least one longitudinal bar or section, the centroid of the additional longitudinal reinforce-
tendon in each corner of the stirrups. Longitudinal bars ment for torsion should approximately coincide with the
shall have a diameter at least 0.042 times the stirrup centroid of the section. The Code accomplishes this by
spacing, but not less than No. 10. requiring the longitudinal torsional reinforcement to be
distributed around the perimeter of the closed stirrups.
Longitudinal bars or tendons are required in each corner of
the stirrups to provide anchorage for the legs of the stirrups.
Corner bars have also been found to be very effective in
developing torsional strength and in controlling cracks.
11.5.6.3 — Torsional reinforcement shall be R11.5.6.3 — The distance (bt + d) beyond the point theoret-
provided for a distance of at least (bt + d) beyond the ically required for torsional reinforcement is larger than that
point required by analysis. used for shear and flexural reinforcement because torsional
diagonal tension cracks develop in a helical form.
11.5.7 — Alternative design for torsion R11.5.7 — Alternative design for torsion
For torsion design of solid sections within the scope of Examples of such procedures are to be found in References
this Code with an aspect ratio, h/bt , of 3 or greater, it 11.39 to 11.41, which have been extensively and successfully
shall be permitted to use another procedure, the used for design of precast, prestressed concrete beams with
adequacy of which has been shown by analysis and ledges. The procedure described in References 11.39 and 11.40
substantial agreement with results of comprehensive is an extension to prestressed concrete sections of the torsion
tests. Sections 11.5.4 and 11.5.6 shall apply. procedures of pre-1995 editions of the Code. The sixth edition
of the PCI Design Handbook11.16 describes the procedure of
References 11.40 and 11.41. This procedure was experi-
mentally verified by the tests described in Reference 11.42.
CODE COMMENTARY
11.6 — Shear-friction R11.6 — Shear-friction
11.6.1 — Provisions of 11.6 are to be applied where it R11.6.1 — With the exception of 11.6, virtually all provisions
is appropriate to consider shear transfer across a regarding shear are intended to prevent diagonal tension
given plane, such as: an existing or potential crack, an failures rather than direct shear transfer failures. The
interface between dissimilar materials, or an interface purpose of 11.6 is to provide design methods for conditions
between two concretes cast at different times. where shear transfer should be considered: an interface
between concretes cast at different times, an interface
between concrete and steel, reinforcement details for precast
concrete structures, and other situations where it is consid-
ered appropriate to investigate shear transfer across a plane
in structural concrete. (See References 11.43 and 11.44.)
11.6.3 — A crack shall be assumed to occur along the R11.6.3 — Although uncracked concrete is relatively strong
11 shear plane considered. The required area of shear- in direct shear, there is always the possibility that a crack will
friction reinforcement Avf across the shear plane shall form in an unfavorable location. The shear-friction concept
be designed using either 11.6.4 or any other shear assumes that such a crack will form, and that reinforcement
transfer design methods that result in prediction of must be provided across the crack to resist relative displace-
strength in substantial agreement with results of ment along it. When shear acts along a crack, one crack face
comprehensive tests. slips relative to the other. If the crack faces are rough and
irregular, this slip is accompanied by separation of the crack
11.6.3.1 — Provisions of 11.6.5 through 11.6.10 shall faces. At ultimate, the separation is sufficient to stress the
apply for all calculations of shear transfer strength. reinforcement crossing the crack to its yield point. The
reinforcement provides a clamping force Avf fy across the
crack faces. The applied shear is then resisted by friction
between the crack faces, by resistance to the shearing off of
protrusions on the crack faces, and by dowel action of the
reinforcement crossing the crack. Successful application of
11.6 depends on proper selection of the location of an
assumed crack.11.16,11.43
Vn = 0.8Avf fy + AcK1
CODE COMMENTARY
In this equation, the first term represents the contribution of
friction to shear-transfer resistance (0.8 representing the
coefficient of friction). The second term represents the sum
of the resistance to shearing of protrusions on the crack
faces and the dowel action of the reinforcement.
CODE COMMENTARY
Equation (11-26) should be used only when the shear force
component parallel to the reinforcement produces tension in
the reinforcement, as shown in Fig. R11.6.4. When α is
greater than 90 degrees, the relative movement of the surfaces
tends to compress the bar and Eq. (11-26) is not valid.
11.6.4.3 — The coefficient of friction μ in Eq. (11-25) R11.6.4.3 — In the shear-friction method of calculation,
and Eq. (11-26) shall be taken as: it is assumed that all the shear resistance is due to the friction
between the crack faces. It is therefore necessary to use
Concrete placed monolithically.......................... 1.4λ artificially high values of the coefficient of friction in the
shear-friction equations so that the calculated shear strength
Concrete placed against hardened will be in reasonable agreement with test results. For concrete
concrete with surface intentionally roughened cast against hardened concrete not roughened in accordance
as specified in 11.6.9......................................... 1.0λ with 11.6.9, shear resistance is primarily due to dowel
Concrete placed against hardened action of the reinforcement and tests11.47 indicate that
concrete not intentionally roughened................. 0.6λ reduced value of μ = 0.6λ specified for this case is appropriate.
Concrete anchored to as-rolled structural The value of μ for concrete placed against as-rolled structural
steel by headed studs or by steel relates to the design of connections between precast
11 reinforcing bars (see 11.6.10)............................ 0.7λ concrete members, or between structural steel members and
structural concrete members. The shear-transfer reinforce-
where λ = 1.0 for normalweight concrete and 0.75 for ment may be either reinforcing bars or headed stud shear
all lightweight concrete. Otherwise, λ shall be deter- connectors; also, field welding to steel plates after casting of
mined based on volumetric proportions of lightweight concrete is common. The design of shear connectors for
and normalweight aggregates as specified in 8.6.1, composite action of concrete slabs and steel beams is not
but shall not exceed 0.85. covered by these provisions, but should be in accordance
with Reference 11.48.
11.6.5 — For normalweight concrete either placed R11.6.5 — These upper limits on shear friction strength are
monolithically or placed against hardened concrete necessary as Eq. (11-25) and (11-26) may become uncon-
with surface intentionally roughened as specified in servative for some cases. Test data11.49,11.50 on normal-
11.6.9, Vn shall not exceed the smallest of 0.2fc′ Ac , weight concrete either placed monolithically or placed
(3.3 + 0.08fc′ )Ac and 11Ac , where Ac is area of against hardened concrete with surface intentionally rough-
concrete section resisting shear transfer. For all other ened as specified in 11.6.9 show that a higher upper limit
cases, Vn shall not exceed the smaller of 0.2fc′ Ac or can be used on shear friction strength for concrete with fc′
5.5Ac . Where concretes of different strengths are cast greater than 28 MPa than was allowed before the 2008 revi-
against each other, the value of fc′ used to evaluate Vn sions. In higher-strength concretes, additional effort may be
shall be that of the lower-strength concrete. required to achieve the roughness specified in 11.6.9.
11.6.7 — Net tension across shear plane shall be R11.6.7 — If a resultant tensile force acts across a shear
resisted by additional reinforcement. Permanent net plane, reinforcement to carry that tension should be
compression across shear plane shall be permitted to provided in addition to that provided for shear transfer.
be taken as additive to Avf fy , the force in the shear- Tension may be caused by restraint of deformations due to
friction reinforcement, when calculating required Avf . temperature change, creep, and shrinkage. Such tensile
forces have caused failures, particularly in beam bearings.
CODE COMMENTARY
of shear-transfer reinforcement provided in the flexural
tension zone. This has been demonstrated experimentally.11.51
11.6.8 — Shear-friction reinforcement shall be appro- R11.6.8 — If no moment acts across the shear plane,
priately placed along the shear plane and shall be reinforcement should be uniformly distributed along the
anchored to develop fy on both sides by embedment, shear plane to minimize crack widths. If a moment acts across
hooks, or welding to special devices. the shear plane, it is desirable to distribute the shear-transfer
reinforcement primarily in the flexural tension zone.
11.7.1 — The provisions of 11.7 shall apply to R11.7.1 — The behavior of a deep beam is discussed in
members with ln not exceeding four times the overall References 11.5 and 11.46. For a deep beam supporting
member depth or regions of beams with concentrated gravity loads, this section applies if the loads are applied on
loads within twice the member depth from the support the top of the beam and the beam is supported on its bottom
that are loaded on one face and supported on the face. If the loads are applied through the sides or bottom of
opposite face so that compression struts can develop such a member, the design for shear should be the same as
between the loads and supports. See also 12.10.6. for ordinary beams.
CODE COMMENTARY
embedment, hooks, or welding to special devices. Bent-up
bars are not recommended.
11.7.2 — Deep beams shall be designed using either R11.7.2 — Deep beams can be designed using strut-and-tie
nonlinear analysis as permitted in 10.7.1, or Appendix A. models, regardless of how they are loaded and supported.
Section 10.7.1 allows the use of nonlinear stress fields when
proportioning deep beams. Such analyses should consider
the effects of cracking on the stress distribution.
11.7.3 — Vn for deep beams shall not exceed R11.7.3 — In the 1999 and earlier Codes, a sliding
0.83 f c′ bwd. maximum shear strength was specified. A re-examination of
the test data suggests that this strength limit was derived
from tests in which the beams failed due to crushing of
support regions. This possibility is specifically addressed in
the design process specified in this Code.
11.7.4 — The area of shear reinforcement perpendicular R11.7.4 and R11.7.5 — The relative amounts of horizontal
to the flexural tension reinforcement, Av, shall not be and vertical shear reinforcement have been interchanged
less than 0.0025bw s, and s shall not exceed the from those required in the 1999 and earlier Codes because
11 smaller of d/5 and 300 mm. tests11.52-11.54 have shown that vertical shear reinforcement
is more effective than horizontal shear reinforcement. The
11.7.5 — The area of shear reinforcement parallel to maximum spacing of bars has been reduced from 450 to
the flexural tension reinforcement, Avh , shall not be 300 mm because this steel is provided to restrain the width
less than 0.0015bws2, and s2 shall not exceed the of the cracks.
smaller of d/5 and 300 mm.
11.8 — Provisions for brackets and corbels R11.8 — Provisions for brackets and corbels
11.8.1 — Brackets and corbels with a shear span-to- R11.8.1 — An upper limit of 1.0 for av /d is imposed for
depth ratio av /d less than 2 shall be permitted to be design by 11.8.3 and 11.8.4 for two reasons. First, for av /d
designed using Appendix A. Design shall be permitted shear span-to-depth ratios exceeding unity, the diagonal
using 11.8.3 and 11.8.4 for brackets and corbels with: tension cracks are less steeply inclined and the use of hori-
zontal stirrups alone as specified in 11.8.4 is not appro-
(a) av /d not greater than 1, and priate. Second, this method of design has only been
validated experimentally for av /d of unity or less. An
(b) subject to factored horizontal tensile force, Nuc , upper limit is provided for Nuc because this method of
not larger than Vu . design has only been validated experimentally for Nuc less
than or equal to Vu , including Nuc equal to zero.
CODE COMMENTARY
The requirements of 11.8.2, 11.8.3.2.1, 11.8.3.2.2,
11.8.5, 11.8.6, and 11.8.7 shall apply to design of
brackets and corbels. Effective depth d shall be deter-
mined at the face of the support.
11
Fig. R11.8.1—Structural action of a corbel.
11.8.2 — Depth at outside edge of bearing area shall R11.8.2 — A minimum depth is required at the outside edge
not be less than 0.5d. of the bearing area so that a premature failure will not occur
due to a major diagonal tension crack propagating from
below the bearing area to the outer sloping face of the corbel
or bracket. Failures of this type have been observed11.55 in
corbels having depths at the outside edge of the bearing area
less than required in this section of the Code.
11.8.3.1 — In all design calculations in accordance R11.8.3.1 — Corbel and bracket behavior is predomi-
with 11.8, φ shall be taken equal to 0.75. nantly controlled by shear; therefore, a single value of φ =
0.75 is required for all design conditions.
CODE COMMENTARY
11.8.3.2 — Design of shear-friction reinforcement,
Avf , to resist Vu shall be in accordance with 11.6.
11.8.3.2.2 — For all-lightweight or sand-lightweight R11.8.3.2.2 — Tests11.56 have shown that the maximum
concrete, Vn shall not be taken greater than the smaller shear strength of lightweight concrete corbels or brackets is
of (0.2 – 0.07av /d)fc′ bwd and (5.5 – 1.9av /d)bwd. a function of both fc′ and av /d. No data are available for
corbels or brackets made of sand-lightweight concrete. As a
result, the same limitations have been placed on both all-
lightweight and sand-lightweight brackets and corbels.
11 11.8.3.4 — Reinforcement An to resist factored R11.8.3.4 — Because the magnitude of horizontal forces
tensile force Nuc shall be determined from φAnfy ≥ acting on corbels or brackets cannot usually be determined
Nuc . Factored tensile force, Nuc , shall not be taken with great accuracy, it is required that Nuc be regarded as a
less than 0.2Vu unless provisions are made to avoid live load.
tensile forces. Nuc shall be regarded as a live load
even if tension results from restraint of creep,
shrinkage, or temperature change.
11.8.3.5 — Area of primary tension reinforcement R11.8.3.5 — Tests11.56 suggest that the total amount of
Asc shall not be less than the larger of (Af + An) and reinforcement (Asc + Ah) required to cross the face of
(2Avf /3 + An). support should be the greater of:
11.8.4 — Total area, Ah , of closed stirrups or ties R11.8.4 — Closed stirrups parallel to the primary tension
parallel to primary tension reinforcement shall not be reinforcement are necessary to prevent a premature diagonal
less than 0.5(Asc – An). Distribute Ah uniformly within tension failure of the corbel or bracket. The required area of
(2/3)d adjacent to primary tension reinforcement. closed stirrups Ah = 0.5 (Asc – An) automatically yields the
appropriate amounts, as discussed in R11.8.3.5 above.
CODE COMMENTARY
11.8.5 — Asc /bd shall not be less than 0.04(fc′ /fy). R11.8.5 — A minimum amount of reinforcement is
required to prevent the possibility of sudden failure should
the bracket or corbel concrete crack under the action of flexural
moment and outward tensile force Nuc.
11.8.6 — At front face of bracket or corbel, primary R11.8.6 — Because the horizontal component of the
tension reinforcement shall be anchored by one of the inclined concrete compression strut (see Fig. R11.8.1) is
following: transferred to the primary tension reinforcement at the location
of the vertical load, the primary tension reinforcement is
(a) By a structural weld to a transverse bar of at least essentially uniformly stressed from the face of the support
equal size; weld to be designed to develop fy of to the point where the vertical load is applied. It should,
primary tension reinforcement; therefore, be anchored at its outer end and in the supporting
column, so as to be able to develop its specified yield
(b) By bending primary tension reinforcement back strength from the face of support to the vertical load. Satis-
to form a horizontal loop; or factory anchorage at the outer end can be obtained by
(c) By some other means of positive anchorage. bending the primary tension reinforcement bars in a horizontal
loop as specified in (b), or by welding a bar of equal diameter
or a suitably sized angle across the ends of the primary
tension reinforcement bars. The welds should be designed
to develop the yield strength of the primary tension rein- 11
forcement. The weld detail used successfully in the corbel
tests reported in Reference 11.56 is shown in Fig. R11.8.6.
The primary tension reinforcement should be anchored
within the supporting column in accordance with the
requirements of Chapter 12. See additional discussion on
end anchorage in R12.10.6.
11.8.7 — Bearing area on bracket or corbel shall not R11.8.7 — The restriction on the location of the bearing
project beyond straight portion of primary tension area is necessary to ensure development of the specified
reinforcement, nor project beyond interior face of yield strength of the primary tension reinforcement near the
transverse anchor bar (if one is provided). load. When corbels are designed to resist horizontal forces,
the bearing plate should be welded to the primary tension
reinforcement.
CODE COMMENTARY
11.9 — Provisions for walls R11.9 — Provisions for walls
11.9.1 — Design for shear forces perpendicular to face R11.9.1 — Shear in the plane of the wall is primarily of
of wall shall be in accordance with provisions for slabs importance for shear walls with a small height-to-length
in 11.11. Design for horizontal in-plane shear forces in ratio. The design of higher walls, particularly walls with
a wall shall be in accordance with 11.9.2 through uniformly distributed reinforcement, will probably be
11.9.9. Alternatively, it shall be permitted to design controlled by flexural considerations.
walls with a height not exceeding two times the length
of the wall for horizontal shear forces in accordance
with Appendix A and 11.9.9.2 through 11.9.9.5.
11.9.3 — Vn at any horizontal section for shear in R11.9.3 — Although the width-to-depth ratio of shear walls
plane of wall shall not be taken greater than is less than that for ordinary beams, tests11.57 on shear walls
0.83 f c′ hd, where h is thickness of wall, and d is with a thickness equal to lw / 25 have indicated that ultimate
11 defined in 11.9.4. shear stresses in excess of 0.83 f c′ can be obtained.
11.9.5 — Unless a more detailed calculation is made R11.9.5 and R11.9.6 — Equations (11-27) and (11-28)
in accordance with 11.9.6, Vc shall not be taken may be used to determine the inclined cracking strength
greater than 0.17λ f c′ hd for walls subject to axial at any section through a shear wall. Equation (11-27) corre-
compression, or Vc shall not be taken greater than the sponds to the occurrence of a principal tensile stress of
value given in 11.2.2.3 for walls subject to axial approximately 0.33λ f c′ at the centroid of the shear wall
tension. cross section. Equation (11-28) corresponds approximately to
the occurrence of a flexural tensile stress of 0.5λ f c′ at a
11.9.6 — Vc shall be permitted to be the lesser of the section lw /2 above the section being investigated. As the term
values computed from Eq. (11-27) and (11-28)
⎛M l
-------u- – ----w-⎞
Nu d ⎝V 2⎠
V c = 0.27λ f c′ hd + ----------
- (11-27) u
4l w
decreases, Eq. (11-27) will control before this term becomes
or negative. When this term becomes negative, Eq. (11-27)
should be used.
Nu ⎞
l w ⎛ 0.1λ f c′ + 0.2 ---------
⎝ l w h⎠
V c = 0.05λ f c′ + ------------------------------------------------------------ hd (11-28)
Mu lw
-------- – -----
Vu 2
CODE COMMENTARY
11.9.7 — Sections located closer to wall base than a R11.9.7 — The values of Vc computed from Eq. (11-27)
distance lw /2 or one-half the wall height, whichever is and (11-28) at a section located a lesser distance of lw / 2 or
less, shall be permitted to be designed for the same Vc hw / 2 above the base apply to that and all sections between
as that computed at a distance lw /2 or one-half the this section and the base. However, the maximum factored
height. shear force Vu at any section, including the base of the wall,
is limited to φVn in accordance with 11.9.3.
11.9.9 — Design of shear reinforcement for walls R11.9.9 — Design of shear reinforcement for walls
11.9.9.1 — Where Vu exceeds φVc , horizontal shear Both horizontal and vertical shear reinforcement are required
reinforcement shall be provided to satisfy Eq. (11-1) for all walls. The notation used to identify the direction of the
and (11-2), where Vs shall be computed by distributed shear reinforcement in walls was updated in 2005
to eliminate conflicts between the notation used for ordinary
Av fy d structural walls in Chapters 11 and 14 and the notation used 11
V s = ---------------
- (11-29) for special structural walls in Chapter 21. The distributed
s
reinforcement is now identified as being oriented parallel to
either the longitudinal or transverse axis of the wall.
where Av is area of horizontal shear reinforcement
Therefore, for vertical wall segments, the notation used to
within spacing s, and d is determined in accordance
describe the horizontal distributed reinforcement ratio is ρ t,
with 11.9.4. Vertical shear reinforcement shall be
and the notation used to describe the vertical distributed
provided in accordance with 11.9.9.4.
reinforcement ratio is ρ l.
11.9.9.2 — Ratio of horizontal shear reinforcement
For low walls, test data11.58 indicate that horizontal shear
area to gross concrete area of vertical section, ρt ,
reinforcement becomes less effective with vertical reinforce-
shall not be less than 0.0025.
ment becoming more effective. This change in effectiveness
of the horizontal versus vertical reinforcement is recognized in
11.9.9.3 — Spacing of horizontal shear reinforce-
Eq. (11-30); if hw/ lw is less than 0.5, the amount of vertical
ment shall not exceed the smallest of lw /5, 3h, and
reinforcement is equal to the amount of horizontal reinforce-
450 mm, where lw is the overall length of the wall.
ment. If hw / lw is greater than 2.5, only a minimum amount of
vertical reinforcement is required (0.0025sh).
11.9.9.4 — Ratio of vertical shear reinforcement
area to gross concrete area of horizontal section, ρl ,
Equation (11-29) is presented in terms of shear strength Vs
shall not be less than the larger of
provided by the horizontal shear reinforcement for direct
application in Eq. (11-1) and (11-2).
h w⎞
ρl = 0.0025 + 0.5 ⎛ 2.5 – ------
- (ρ – 0.0025) (11-30)
⎝ lw ⎠ t Vertical shear reinforcement also should be provided in
accordance with 11.9.9.4 within the spacing limitation of
and 0.0025, The value of ρl calculated by Eq. (11-30) 11.9.9.5.
need not be greater than ρt required by 11.9.9.1. In
Eq. (11-30), lw is the overall length of the wall, and hw
is the overall height of the wall.
CODE COMMENTARY
11.10 — Transfer of moments to columns R11.10 — Transfer of moments to columns
11.10.1 — When gravity load, wind, earthquake, or R11.10.1 — Tests11.59 have shown that the joint region of a
other lateral forces cause transfer of moment at beam-to-column connection in the interior of a building
connections of framing elements to columns, the does not require shear reinforcement if the joint is confined
shear resulting from moment transfer shall be consid- on four sides by beams of approximately equal depth.
ered in the design of lateral reinforcement in the However, joints without lateral confinement, such as at the
columns. exterior of a building, need shear reinforcement to prevent
deterioration due to shear cracking.11.60
11.11 — Provisions for slabs and footings R11.11 — Provisions for slabs and footings
11.11.1 — The shear strength of slabs and footings in R11.11.1 — Differentiation should be made between a long
the vicinity of columns, concentrated loads, or reactions and narrow slab or footing acting as a beam, and a slab or
is governed by the more severe of two conditions: footing subject to two-way action where failure may occur
by punching along a truncated cone or pyramid around a
11.11.1.1 — Beam action where each critical section concentrated load or reaction area.
to be investigated extends in a plane across the entire
width. For beam action, the slab or footing shall be
designed in accordance with 11.1 through 11.4.
11.11.1.2 — For two-way action, each of the critical R11.11.1.2 — The critical section for shear in slabs
sections to be investigated shall be located so that its subjected to bending in two directions follows the perim-
perimeter bo is a minimum but need not approach eter at the edge of the loaded area.11.3 The shear stress
closer than d/2 to: acting on this section at factored loads is a function of
f c′ and the ratio of the side dimension of the column to
(a) Edges or corners of columns, concentrated the effective slab depth. A much simpler design equation
loads, or reaction areas; and results by assuming a pseudocritical section located at a
distance d/2 from the periphery of the concentrated load.
(b) Changes in slab thickness such as edges of When this is done, the shear strength is almost independent of
capitals, drop panels, or shear caps. the ratio of column size to slab depth. For rectangular
For two-way action, the slab or footing shall be columns, this critical section was defined by straight lines
designed in accordance with 11.11.2 through 11.11.6. drawn parallel to and at a distance d/2 from the edges of
the loaded area. Section 11.11.1.3 allows the use of a
rectangular critical section.
CODE COMMENTARY
For edge columns at points where the slab cantilevers
beyond the column, the critical perimeter will either be
three-sided or four-sided.
11.11.2.1 — For nonprestressed slabs and footings, R11.11.2.1 — For square columns, the shear stress due to
Vc shall be the smallest of (a), (b), and (c): ultimate loads in slabs subjected to bending in two directions is
limited to 0.33λ f c′ . However, tests11.61 have indicated
that the value of 0.33λ f c′ is unconservative when the ratio 11
V c = 0.17 ⎛ 1 + ---⎞ λ f c′ b o d
2
(a) (11-31) β of the lengths of the long and short sides of a rectangular
⎝ β⎠
column or loaded area is larger than 2.0. In such cases, the
actual shear stress on the critical section at punching shear
where β is the ratio of long side to short side of the
failure varies from a maximum of about 0.33λ f c′ around
column, concentrated load or reaction area;
the corners of the column or loaded area, down to
0.17λ f c′ or less along the long sides between the two end
αs d sections. Other tests11.62 indicate that vc decreases as the
(b) V c = 0.083 ⎛ ---------
- + 2⎞ λ f c′ b o d (11-32)
⎝ b ⎠ ratio bo /d increases. Equations (11-31) and (11-32) were devel-
o
oped to account for these two effects. The words “interior,”
where αs is 40 for interior columns, 30 for edge “edge,” and “corner columns” in 11.11.2.1(b) refer to critical
columns, 20 for corner columns; and sections with four, three, and two sides, respectively.
11.11.2.2 — At columns of two-way prestressed R11.11.2.2 — For prestressed slabs and footings, a
slabs and footings that meet the requirements of modified form of Code Eq. (11-31) and (11-34) is specified
18.9.3 for two-way action shear strength. Research11.63,11.64 indicates
that the shear strength of two-way prestressed slabs around
V c = ( β p λ f c′ + 0.3f pc )b o d + V p (11-34) interior columns is conservatively predicted by Eq. (11-34).
Vc from Eq. (11-34) corresponds to a diagonal tension
failure of the concrete initiating at the critical section
where βp is the smaller of 3.5 and 0.083(αsd/bo + defined in 11.11.1.2. The mode of failure differs from a
1.5), αs is 40 for interior columns, 30 for edge punching shear failure of the concrete compression zone
columns, and 20 for corner columns, bo is perimeter of around the perimeter of the loaded area predicted by Eq.
critical section defined in 11.11.1.2, fpc is taken as the (11-31). Consequently, the term β does not enter into Eq.
average value of fpc for the two directions, and Vp is (11-34). Values for f c′ and fpc are restricted in design due
the vertical component of all effective prestress forces to limited test data available for higher values. When
crossing the critical section. Vc shall be permitted to computing fpc, loss of prestress due to restraint of the slab
be computed by Eq. (11-34) if the following are satisfied; by shear walls and other structural elements should be taken
otherwise, 11.11.2.1 shall apply: into account.
CODE COMMENTARY
(a) No portion of the column cross section shall be
closer to a discontinuous edge than four times the
slab thickness;
(c) In each direction, fpc shall not be less than 0.9 MPa,
nor be taken greater than 3.5 MPa.
11
Fig. R11.11.2—Value of β for a nonrectangular loaded area.
11.11.3 — Shear reinforcement consisting of bars or R11.11.3 — Research11.65-11.69 has shown that shear
wires and single- or multiple-leg stirrups shall be reinforcement consisting of properly anchored bars or wires
permitted in slabs and footings with d greater than or and single- or multiple-leg stirrups, or closed stirrups, can
equal to 150 mm, but not less than 16 times the shear increase the punching shear resistance of slabs. The spacing
reinforcement bar diameter. Shear reinforcement shall limits given in 11.11.3.3 correspond to slab shear reinforce-
be in accordance with 11.11.3.1 through 11.11.3.4. ment details that have been shown to be effective. Sections
12.13.2 and 12.13.3 give anchorage requirements for stirrup-
11.11.3.1 — Vn shall be computed by Eq. (11-2), type shear reinforcement that should also be applied for bars
where Vc shall not be taken greater than 0.17λ f c′ bod, or wires used as slab shear reinforcement. It is essential that
and Vs shall be calculated in accordance with 11.4. In this shear reinforcement engage longitudinal reinforcement at
Eq. (11-15), Av shall be taken as the cross-sectional both the top and bottom of the slab, as shown for typical
area of all legs of reinforcement on one peripheral line details in Fig. R11.11.3(a) to (c). Anchorage of shear
that is geometrically similar to the perimeter of the reinforcement according to the requirements of 12.13 is
column section. difficult in slabs thinner than 250 mm. Shear reinforcement
consisting of vertical bars mechanically anchored at each end
11.11.3.2 — Vn shall not be taken greater than by a plate or head capable of developing the yield strength of
0.5 f c′ bod. the bars has been used successfully.11.69
CODE COMMENTARY
CODE COMMENTARY
11.11.3.3 — The distance between the column face
and the first line of stirrup legs that surround the
column shall not exceed d/2. The spacing between
adjacent stirrup legs in the first line of shear reinforce-
ment shall not exceed 2d measured in a direction
parallel to the column face. The spacing between
successive lines of shear reinforcement that surround
the column shall not exceed d/2 measured in a direc-
tion perpendicular to the column face.
11
11.11.4 — Shear reinforcement consisting of structural R11.11.4 — Based on reported test data,11.70 design proce-
steel I- or channel-shaped sections (shearheads) shall dures are presented for shearhead reinforcement consisting
be permitted in slabs. The provisions of 11.11.4.1 of structural steel shapes. For a column connection transferring
through 11.11.4.9 shall apply where shear due to gravity moment, the design of shearheads is given in 11.11.7.3.
load is transferred at interior column supports. Where
moment is transferred to columns, 11.11.7.3 shall apply. Three basic criteria should be considered in the design of
shearhead reinforcement for connections transferring shear
11.11.4.1 — Each shearhead shall consist of steel due to gravity load. First, a minimum flexural strength
shapes fabricated by welding with a full penetration should be provided to ensure that the required shear strength
weld into identical arms at right angles. Shearhead of the slab is reached before the flexural strength of the
arms shall not be interrupted within the column section. shearhead is exceeded. Second, the shear stress in the slab at
CODE COMMENTARY
11.11.4.2 — A shearhead shall not be deeper than
70 times the web thickness of the steel shape.
11
the end of the shearhead reinforcement should be limited.
Third, after these two requirements are satisfied, the
negative moment slab reinforcement can be reduced in
proportion to the moment contribution of the shearhead at
the design section.
11.11.4.5 — The ratio αv between the flexural stiff- R11.11.4.5 and R11.11.4.6 — The assumed idealized
ness of each shearhead arm and that of the shear distribution along an arm of a shearhead at an interior
surrounding composite cracked slab section of width column is shown in Fig. R11.11.4.5. The shear along each of
(c2 + d) shall not be less than 0.15. the arms is taken as αvφVc /n, where Vc is defined in
11.11.2.1(c). However, the peak shear at the face of the
11.11.4.6 — Plastic moment strength, Mp , required column is taken as the total shear considered per arm Vu /n
for each arm of the shearhead shall be computed by minus the shear considered carried to the column by the
concrete compression zone of the slab. The latter term is
Vu c expressed as φ(Vc /n)(1 – αv), so that it approaches zero for a
M p = ---------- h v + α v ⎛ l v – -----1-⎞ (11-35) heavy shearhead and approaches Vu /n when a light shear-
2φn ⎝ 2⎠
head is used. Equation (11-35) then follows from the
assumption that φVc is about one-half the factored shear
where φ is for tension-controlled members, n is
force Vu. In this equation, Mp is the required plastic moment
number of shearhead arms, and lv is minimum length
strength of each shearhead arm necessary to ensure that Vu
of each shearhead arm required to comply with
is attained as the moment strength of the shearhead is
requirements of 11.11.4.7 and 11.11.4.8.
reached. The quantity lv is the length from the center of the
column to the point at which the shearhead is no longer
required, and the distance c1 /2 is one-half the dimension of
the column in the direction considered.
11.11.4.7 — The critical slab section for shear shall R11.11.4.7 — The test results11.70 indicated that slabs
be perpendicular to the plane of the slab and shall containing under-reinforcing shearheads failed at a shear
cross each shearhead arm at three-quarters the stress on a critical section at the end of the shearhead
distance [lv – (c1/2)] from the column face to the end reinforcement less than 0.33 f c′ . Although the use of over-
of the shearhead arm. The critical section shall be reinforcing shearheads brought the shear strength back to
located so that its perimeter bo is a minimum, but need about the equivalent of 0.33 f c′ , the limited test data suggest
not be closer than the perimeter defined in 11.11.1.2(a). that a conservative design is desirable. Therefore, the shear
strength is calculated as 0.33 f c′ on an assumed critical
section located inside the end of the shearhead reinforcement.
CODE COMMENTARY
11
11.11.4.9 — Moment resistance Mv contributed to R11.11.4.9 — If the peak shear at the face of the column
each slab column strip by a shearhead shall not be is neglected, and φVc is again assumed to be about one-half
taken greater than of Vu , the moment resistance contribution of the shearhead
Mv can be conservatively computed from Eq. (11-36), in
φα v V u ⎛ c which φ is the factor for flexure.
- l v – -----1-⎞
M v = ---------------- (11-36)
2n ⎝ 2⎠
CODE COMMENTARY
(b) The change in column strip moment over the
length lv ;
11.11.5 — Headed shear stud reinforcement, placed R11.11.5 — Headed shear stud reinforcement was intro-
perpendicular to the plane of a slab or footing, shall be duced in the 2008 Code. Using headed stud assemblies, as
permitted in slabs and footings in accordance with shear reinforcement in slabs and footings, requires speci-
11.11.5.1 through 11.11.5.4. The overall height of the fying the stud shank diameter, the spacing of the studs, and
shear stud assembly shall not be less than the thick- the height of the assemblies for the particular applications.
ness of the member less the sum of: (1) the concrete
cover on the top flexural reinforcement; (2) the Tests11.69 show that vertical studs mechanically anchored as
concrete cover on the base rail; and (3) one-half the close as possible to the top and bottom of slabs are effective in
bar diameter of the tension flexural reinforcement. resisting punching shear. The bounds of the overall specified
Where flexural tension reinforcement is at the bottom height achieve this objective while providing a reasonable
of the section, as in a footing, the overall height of the tolerance in specifying that height as shown in Fig. R7.7.5.
11
shear stud assembly shall not be less than the thick-
ness of the member less the sum of: (1) the concrete Compared with a leg of a stirrup having bends at the ends, a
cover on the bottom flexural reinforcement; (2) the stud head exhibits smaller slip, and thus results in smaller
concrete cover on the head of the stud; and (3) one-half shear crack widths. The improved performance results in
the bar diameter of the bottom flexural reinforcement. larger limits for shear strength and spacing between peripheral
lines of headed shear stud reinforcement. Typical
arrangements of headed shear stud reinforcement are shown
in Fig. R11.11.5. The critical section beyond the shear
reinforcement generally has a polygonal shape. Equations
for calculating shear stresses on such sections are given in
Reference 11.69.
11.11.5.1 — For the critical section defined in R11.11.5.1 — When there is unbalanced moment
11.11.1.2, Vn shall be computed using Eq. (11-2), with transfer, the design will be based on stresses. The maximum
Vc and Vn not exceeding 0.25λ f c′ bod and shear stress due to a combination of Vu and the fraction of
0.66 f c′ bod, respectively. Vs shall be calculated unbalanced moment γvMu should not exceed φvn, where vn
using Eq. (11-15) with Av equal to the cross-sectional is taken as the sum of 0.25λ f c′ and Av fyt /(bos).
area of all the shear reinforcement on one peripheral
line that is approximately parallel to the perimeter of
the column section, where s is the spacing of the
peripheral lines of headed shear stud reinforcement.
Avfyt /(bos) shall not be less than 0.17 f c′ .
11.11.5.2 — The spacing between the column face R11.11.5.2 — The specified spacings between peripheral
and the first peripheral line of shear reinforcement lines of shear reinforcement are justified by experiments.11.69
shall not exceed d/2. The spacing between peripheral The clear spacing between the heads of the studs should be
lines of shear reinforcement, measured in a direction adequate to permit placing of the flexural reinforcement.
perpendicular to any face of the column, shall be
constant. For prestressed slabs or footings satisfying
11.11.2.2, this spacing shall not exceed 0.75d; for all
other slabs and footings, the spacing shall be based
on the value of the shear stress due to factored shear
force and unbalanced moment at the critical section
defined in 11.11.1.2, and shall not exceed:
CODE COMMENTARY
11
Fig. R11.11.5—Typical arrangements of headed shear stud reinforcement and critical sections.
CODE COMMENTARY
11.11.6 — Openings in slabs R11.11.6 — Openings in slabs
When openings in slabs are located at a distance less Provisions for design of openings in slabs (and footings) were
than 10 times the slab thickness from a concentrated developed in Reference 11.3. The locations of the effective
load or reaction area, or when openings in flat slabs portions of the critical section near typical openings and free
are located within column strips as defined in edges are shown by the dashed lines in Fig. R11.11.6.
Chapter 13, the critical slab sections for shear defined Additional research11.61 has confirmed that these provisions
in 11.11.1.2 and 11.11.4.7 shall be modified as follows: are conservative.
11.11.7.1 — Where gravity load, wind, earthquake, R11.11.7.1 — In Reference 11.71 it was found that where
or other lateral forces cause transfer of unbalanced moment is transferred between a column and a slab, 60 percent
moment Mu between a slab and column, γf Mu shall be of the moment should be considered transferred by flexure
transferred by flexure in accordance with 13.5.3. The across the perimeter of the critical section defined in
remainder of the unbalanced moment, γv Mu , shall be 11.11.1.2, and 40 percent by eccentricity of the shear about
considered to be transferred by eccentricity of shear the centroid of the critical section. For rectangular columns,
about the centroid of the critical section defined in the portion of the moment transferred by flexure increases as
11.11.1.2 where the width of the face of the critical section resisting the
moment increases, as given by Eq. (13-1).
γv = (1 – γf ) (11-37)
CODE COMMENTARY
11
11.11.7.2 — The shear stress resulting from R11.11.7.2 — The stress distribution is assumed as illus-
moment transfer by eccentricity of shear shall be trated in Fig. R11.11.7.2 for an interior or exterior column.
assumed to vary linearly about the centroid of the critical The perimeter of the critical section, ABCD, is determined
sections defined in 11.11.1.2. The maximum shear in accordance with 11.11.1.2. The factored shear force Vu
stress due to Vu and Mu shall not exceed φvn: and unbalanced factored moment Mu are determined at the
centroidal axis c-c of the critical section. The maximum
(a) For members without shear reinforcement, factored shear stress may be calculated from
CODE COMMENTARY
3 3 2
d ( c1 + d ) ( c 1 + d )d d ( c2 + d ) ( c1 + d )
= ------------------------
- + ------------------------
- + --------------------------------------------
-
6 6 2
Similar equations may be developed for Ac and Jc for
columns located at the edge or corner of a slab.
11
12.1.1 — Calculated tension or compression in reinforce- The development length concept for anchorage of reinforce-
ment at each section of structural concrete members ment was first introduced in the 1971 Code, to replace the
shall be developed on each side of that section by dual requirements for flexural bond and anchorage bond
embedment length, hook, headed deformed bar or contained in earlier editions. It is no longer necessary to
mechanical device, or a combination thereof. Hooks consider the flexural bond concept, which placed emphasis
and heads shall not be used to develop bars in on the computation of nominal peak bond stresses. Consid-
compression. eration of an average bond resistance over a full development
length of the reinforcement is more meaningful, partially
12.1.2 — The values of f c′ used in this chapter shall because all bond tests consider an average bond resistance
not exceed 8.3 MPa. over a length of embedment of the reinforcement, and
partially because uncalculated extreme variations in local
12.1.3 — In addition to requirements in this chapter that bond stresses exist near flexural cracks.12.1
affect detailing of reinforcement, structural integrity
requirements of 7.13 shall be satisfied. The development length concept is based on the attainable
12
average bond stress over the length of embedment of the
reinforcement. Development lengths are required because of
the tendency of highly stressed bars to split relatively thin
sections of restraining concrete. A single bar embedded in a
mass of concrete should not require as great a development
length; although a row of bars, even in mass concrete, can
create a weakened plane with longitudinal splitting along
the plane of the bars.
CODE COMMENTARY
12.2 — Development of deformed bars R12.2 — Development of deformed bars
and deformed wire in tension and deformed wire in tension
12.2.1 — Development length for deformed bars and The general development length equation (Eq. (12-1)) is
deformed wire in tension, ld , shall be determined from given in 12.2.3. The equation is based on the expression for
either 12.2.2 or 12.2.3 and applicable modification development length previously endorsed by Committee
factors of 12.2.4 and 12.2.5, but ld shall not be less 408.12.2,12.3 In Eq. (12-1), cb is a factor that represents the
than 300 mm. smallest of the side cover, the cover over the bar or wire (in
both cases measured to the center of the bar or wire), or one-
12.2.2 — For deformed bars or deformed wire, ld shall half the center-to-center spacing of the bars or wires. Ktr is a
be as follows: factor that represents the contribution of confining reinforce-
ment across potential splitting planes. ψt is the traditional
No. 19 and reinforcement location factor to reflect the adverse effects of
smaller bars and No. 22 and
Spacing and cover deformed wires larger bars the top reinforcement casting position. ψe is a coating factor
Clear spacing of bars or wires reflecting the effects of epoxy coating. There is a limit on the
being developed or spliced not product ψtψe. The reinforcement size factor ψs reflects the
less than db , clear cover not
more favorable performance of smaller-diameter reinforce-
less than db , and stirrups or ties
throughout ld not less than the ⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞ ment. In 2008, a revision was made to the λ term which is
Code minimum ⎜ -----------------------⎟ d b ⎜ -----------------------⎟ d b essentially the inverse of the λ used previously in Chapter 12.
or ⎝ 2.1λ f c′ ⎠ ⎝ 1.7λ f c′ ⎠
Clear spacing of bars or wires
A limit of 2.5 is placed on the term (cb + Ktr)/db. When (cb +
being developed or spliced not Ktr)/db is less than 2.5, splitting failures are likely to occur.
12 less than 2db and clear cover For values above 2.5, a pullout failure is expected and an
not less than db
increase in cover or transverse reinforcement is unlikely to
⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞ increase the anchorage capacity.
Other cases ⎜ -----------------------⎟ d b ⎜ -----------------------⎟ d b
⎝ 1.4λ f c′ ⎠ ⎝ 1.1λ f c′ ⎠
Equation (12-1) includes the effects of all variables controlling
the development length. Terms in Eq. (12-1) may be
12.2.3 — For deformed bars or deformed wire, ld shall be
disregarded when such omission results in longer and
hence, more conservative, development lengths.
⎛ ⎞
⎜ fy ψt ψe ψs ⎟
ld = ⎜ ----------------------- ---------------------------⎟ d b (12-1) The provisions of 12.2.2 and 12.2.3 give a two-tier
⎜ 1.1λ f c′ ⎛ c b + K tr⎞ ⎟ approach. The user can either calculate ld based on the
⎝ ⎝ --------------------
db ⎠ ⎠
-
actual (cb + Ktr)/db (12.2.3) or calculate ld using 12.2.2,
which is based on two preselected values of (cb + Ktr)/db.
in which the confinement term (cb + Ktr )/db shall not
be taken greater than 2.5, and Section 12.2.2 recognizes that many current practical
construction cases utilize spacing and cover values along
with confining reinforcement, such as stirrups or ties, that
40A tr
K tr = --------------
- (12-2) result in a value of (cb + Ktr)/db of at least 1.5. Examples
sn include a minimum clear cover of db along with either
minimum clear spacing of 2db, or a combination of
where n is the number of bars or wires being spliced minimum clear spacing of db and minimum ties or stirrups.
or developed along the plane of splitting. It shall be For these frequently occurring cases, the development
permitted to use Ktr = 0 as a design simplification even length for larger bars can be taken as ld = [fyψtψe /
if transverse reinforcement is present. (1.7 f c′ )]db. In the development of ACI 318-95, a compar-
ison with past provisions and a check of a database of exper-
imental results maintained by ACI Committee 40812.2
indicated that for No. 19 deformed bars and smaller, as well
as for deformed wire, the development lengths could be
reduced 20 percent using ψs = 0.8. This is the basis for the
middle column of the table in 12.2.2. With less cover and in
the absence of minimum ties or stirrups, the minimum clear
spacing limits of 7.6.1 and the minimum concrete cover
requirements of 7.7 result in minimum values of cb equal to
db. Thus, for “other cases,” the values are based on using
(cb + Ktr)/db = 1.0 in Eq. (12-1).
CODE COMMENTARY
The user may easily construct simple, useful expressions.
For example, in all structures with normalweight concrete
(λ = 1.0), uncoated reinforcement (ψe = 1.0), No. 22 or
larger bottom bars (ψt = 1.0) with fc′ = 28 MPa and
Grade 420 reinforcement, the equations reduce to
(420)(1.0)(1.0)
l d = ------------------------------------ d b = 47d b
1.7 ( 1.0 ) 28
oder
(420)(1.0)(1.0)
l d = ------------------------------------ d b = 72d b
1.1 ( 1.0 ) 28
Before ACI 318-08, Eq. (12-2) for Ktr included the yield
strength of transverse reinforcement. The current expression
includes only the area and spacing of the transverse reinforce-
ment and the number of wires or bars being developed or lap
spliced because tests demonstrate that transverse reinforce-
ment rarely yields during a bond failure.12.4
12.2.4 — The factors used in the expressions for R12.2.4 — The reinforcement location factor ψt accounts
development of deformed bars and deformed wires in for position of the reinforcement in freshly placed concrete.
tension in 12.2 are as follows: The factor was reduced to 1.3 in the 1989 Code to reflect
research.12.5,12.6
(a) Where horizontal reinforcement is placed such
that more than 300 mm of fresh concrete is cast The factor λ for lightweight concrete was made the same for
below the development length or splice, ψt = 1.3. For all types of lightweight aggregates in the 1989 Code.
other situations, ψt = 1.0. Research on hooked bar anchorages did not support the
variations in previous Codes for all-lightweight and sand-
(b) For epoxy-coated bars or wires with cover less lightweight concrete and a single value, 1.3 (used at that
than 3db , or clear spacing less than 6db , ψe = 1.5. time as a multiplier in the numerator of development length
For all other epoxy-coated bars or wires, ψe = 1.2. equations), was selected. A unified definition of λ was
For uncoated and zinc-coated (galvanized) reinforce- adopted in the 2008 Code. Because a single definition of λ
ment, ψe = 1.0. is now used in the Code, the term λ has been moved from
However, the product ψtψe need not be greater than 1.7. the numerator to the denominator in the development length
equations (1/0.75 = 1.33). Section 12.2.4 allows a higher
(c) For No. 19 and smaller bars and deformed wires, factor to be used when the splitting tensile strength of the
ψs = 0.8. For No. 22 and larger bars, ψs = 1.0. lightweight concrete is specified. See 5.1.4.
CODE COMMENTARY
(d) Where lightweight concrete is used, λ shall not Studies12.7-12.9 of the anchorage of epoxy-coated bars show
exceed 0.75 unless fct is specified (see 8.6.1). that bond strength is reduced because the coating prevents
Where normalweight concrete is used, λ = 1.0. adhesion and friction between the bar and the concrete. The
factors reflect the type of anchorage failure likely to occur.
When the cover or spacing is small, a splitting failure can
occur and the anchorage or bond strength is substantially
reduced. If the cover and spacing between bars is large, a
splitting failure is precluded and the effect of the epoxy
coating on anchorage strength is not as large. Studies12.10
have shown that although the cover or spacing may be
small, the anchorage strength may be increased by adding
transverse steel crossing the plane of splitting, and
restraining the splitting crack.
Reduction in ld shall be permitted where reinforce- The reduction factor based on area is not to be used in those
ment in a flexural member is in excess of that cases where anchorage development for full fy is required.
required by analysis except where anchorage or For example, the excess reinforcement factor does not apply
development for fy is specifically required or the for development of positive moment reinforcement at
reinforcement is designed under provisions of supports according to 12.11.2, for development of shrinkage
21.1.1.6..................... (As required)/(As provided). and temperature reinforcement according to 7.12.2.3, or for
development of reinforcement provided according to 7.13
and 13.3.8.5.
12.3.1 — Development length for deformed bars and The weakening effect of flexural tension cracks is not
deformed wire in compression, ldc , shall be determined present for bars and wire in compression, and usually end
from 12.3.2 and applicable modification factors of bearing of the bars on the concrete is beneficial. Therefore,
12.3.3, but ldc shall not be less than 200 mm. shorter development lengths are specified for compression
than for tension. The development length may be reduced
12.3.2 — For deformed bars and deformed wire, ldc 25 percent when the reinforcement is enclosed within
shall be taken as the larger of (0.24fy /λ f c′ )db and spirals or ties. A reduction in development length is also
(0.043fy)db , with λ as given in 12.2.4(d) and the permitted if excess reinforcement is provided.
constant 0.043 carries the unit of mm2/N.
In 2008, the term λ was added to the expression for develop-
12.3.3 — Length ldc in 12.3.2 shall be permitted to be ment in 12.3.2 recognizing that there is no known test data
multiplied by the applicable factors for: on compression development in lightweight concrete but
that splitting is more likely in lightweight concrete.
CODE COMMENTARY
(a) Reinforcement in excess of that required by
analysis.................... (As required)/(As provided)
12.4.1 — Development length of individual bars within R12.4.1 — An increased development length for individual
a bundle, in tension or compression, shall be that for bars is required when three or four bars are bundled
the individual bar, increased 20 percent for three-bar together. The extra extension is needed because the grouping
bundle, and 33 percent for four-bar bundle. makes it more difficult to mobilize bond resistance from the
core between the bars.
12.4.2 — For determining the appropriate spacing and R12.4.2 — Although splice and development lengths of
cover values in 12.2.2, the confinement term in 12.2.3, bundled bars are a multiple of the diameter of the individual
and the ψe factor in 12.2.4(b), a unit of bundled bars bars being spliced increased by 20 or 33 percent, as appro-
shall be treated as a single bar of a diameter derived priate, it is necessary to use an equivalent diameter of the
from the equivalent total area and having a centroid entire bundle derived from the equivalent total area of bars
that coincides with that of the bundled bars. when determining the spacing and cover values in 12.2.2,
the confinement term, [(cb + Ktr)/db], in 12.2.3, and the ψe
factor in 12.2.4(b). For bundled bars, bar diameter, db,
outside the brackets in the expressions of 12.2.2 and of
Eq. (12-1) is that of a single bar.
12.5.1 — Development length for deformed bars in The provisions for hooked bar anchorage were extensively
tension terminating in a standard hook (see 7.1), ldh , revised in the 1983 Code. Study of failures of hooked bars
shall be determined from 12.5.2 and the applicable indicate that splitting of the concrete cover in the plane of
modification factors of 12.5.3, but ldh shall not be less the hook is the primary cause of failure and that splitting
than the larger of 8db and 150 mm. originates at the inside of the hook where the local stress
concentrations are very high. Thus, hook development is a
12.5.2 — For deformed bars, ldh shall be (0.24ψefy / direct function of bar diameter db,which governs the magni-
λ f c′ )db with ψe taken as 1.2 for epoxy-coated tude of compressive stresses on the inside of the hook. Only
reinforcement, and λ taken as 0.75 for lightweight standard hooks (see 7.1) are considered and the influence of
concrete. For other cases, ψe and λ shall be taken as 1.0. larger radius of bend cannot be evaluated by 12.5.
12.5.3 — Length ldh in 12.5.2 shall be permitted to be The hooked bar anchorage provisions give the total hooked
multiplied by the following applicable factors: bar embedment length as shown in Fig. R12.5. The develop-
ment length ldh is measured from the critical section to the
(a) For No. 36 bar and smaller hooks with side cover outside end (or edge) of the hook.
(normal to plane of hook) not less than 65 mm, and
CODE COMMENTARY
for 90-degree hook with cover on bar extension
beyond hook not less than 50 mm....................... 0.7
In 12.5.3(b) and 12.5.3(c), db is the diameter of the The development length for standard hooks ldh of 12.5.2 can
hooked bar, and the first tie or stirrup shall enclose the be reduced by all applicable modification factors of 12.5.3.
12 bent portion of the hook, within 2db of the outside of As an example, if the conditions of both 12.5.3(a) and (c)
the bend. are met, both factors may be applied.
CODE COMMENTARY
12
12.5.4 — For bars being developed by a standard R12.5.4 — Bar hooks are especially susceptible to a
hook at discontinuous ends of members with both side concrete splitting failure if both side cover (normal to plane
cover and top (or bottom) cover over hook less than of hook) and top or bottom cover (in plane of hook) are
65 mm, the hooked bar shall be enclosed within ties or small. See Fig. R12.5.4. With minimum confinement
stirrups perpendicular to the bar being developed, provided by concrete, additional confinement provided by
spaced not greater than 3db along ldh . The first tie or ties or stirrups is essential, especially if full bar strength
stirrup shall enclose the bent portion of the hook, should be developed by a hooked bar with such small cover.
within 2db of the outside of the bend, where db is the Cases where hooks may require ties or stirrups for confinement
diameter of the hooked bar. For this case, the factors are at ends of simply supported beams, at free end of
of 12.5.3(b) and (c) shall not apply. cantilevers, and at ends of members framing into a joint
CODE COMMENTARY
where members do not extend beyond the joint. In contrast, if
calculated bar stress is so low that the hook is not needed for
bar anchorage, the ties or stirrups are not necessary. Also,
provisions of 12.5.4 do not apply for hooked bars at discon-
tinuous ends of slabs with confinement provided by the slab
continuous on both sides normal to the plane of the hook.
12.5.5 — Hooks shall not be considered effective in R12.5.5 — In compression, hooks are ineffective and may
developing bars in compression. not be used as anchorage.
12.6.1 — Development length for headed deformed The development of headed deformed bars and the develop-
bars in tension, ldt , shall be determined from 12.6.2. ment and anchorage of reinforcement through the use of
Use of heads to develop deformed bars in tension mechanical devices within concrete are addressed in 12.6.
shall be limited to conditions satisfying (a) through (f): As used in 12.6, development describes cases in which the
force in the bar is transferred to the concrete through a
(a) Bar fy shall not exceed 420 MPa; combination of a bearing force at the head and bond forces
12 along the bar, such cases are covered in 12.6.1 and 12.6.2. In
(b) Bar size shall not exceed No. 36; contrast, anchorage describes cases in which the force in the
(c) Concrete shall be normalweight; bar is transferred through bearing to the concrete at the head
alone. General provisions for anchorage are given in
(d) Net bearing area of head Abrg shall not be less Appendix D. The limitation on obstructions and interrup-
than 4Ab; tions of the deformations is included in 3.5.9 because there
is a wide variety of methods to attach heads to bars, some of
(e) Clear cover for bar shall not be less than 2db ; which involve obstructions or interruptions of the deformations
and that extend more than 2db from the bearing face of the head.
(f) Clear spacing between bars shall not be less These systems were not evaluated in the tests used to formulate
than 4db . the provisions in 12.6.2, which were limited to systems that
meet the criteria in 3.5.9.
12.6.2 — For headed deformed bars satisfying 3.5.9,
development length in tension ldt shall be (0.19ψefy / The provisions for headed deformed bars were written with
f c′ )db , where the value of fc′ used to calculate ldt due consideration of the provisions for anchorage in
shall not exceed 40 MPa, and factor ψe shall be taken Appendix D and the bearing strength provisions of
as 1.2 for epoxy-coated reinforcement and 1.0 for 10.14.12.15,12.16 Appendix D contains provisions for headed
other cases. Where reinforcement provided is in anchors related to the individual failure modes of concrete
excess of that required by analysis, except where breakout, side-face blowout, and pullout, all of which were
development of fy is specifically required, a factor of considered in the formulation of 12.6.2. The restrictions on
(As required)/(As provided) may be applied to the normalweight concrete, maximum bar size of No. 36, and
expression for ldt . Length ldt shall not be less than the upper limit of 420 MPa for fy are based on the available data
larger of 8db and 150 mm. from tests.12.15-12.17
CODE COMMENTARY
12
CODE COMMENTARY
improving the anchorage of headed deformed bars,12.15-12.17
additional reductions in development length, such as those
allowed for standard hooks with additional confinement
provided by transverse reinforcement in 12.5.3, are not used
for headed deformed reinforcing bars. Transverse reinforce-
ment, however, helps limit splitting cracks in the vicinity of
the head and for that reason is recommended.
12.6.3 — Heads shall not be considered effective in R12.6.3 — No data are available that demonstrate that the
developing bars in compression. use of heads adds significantly to anchorage strength in
12 compression.
12.6.4 — Any mechanical attachment or device R12.6.4 — Headed deformed reinforcement that does not
capable of developing fy of reinforcement is allowed, meet the requirements in 3.5.9, including the limitation on
provided that test results showing the adequacy of obstructions and interruptions of the deformations, or is not
such attachment or device are approved by the anchored in accordance with 12.6.1 and 12.6.2 may be used
building official. Development of reinforcement shall be if tests demonstrate the ability of the head and bar system to
permitted to consist of a combination of mechanical develop or anchor the desired force in the bar, as described
anchorage plus additional embedment length of in 12.6.4.
reinforcement between the critical section and the
mechanical attachment or device.
12.7.1 — Development length for welded deformed wire Figure R12.7 shows the development requirements for welded
reinforcement in tension, ld , measured from the point of deformed wire reinforcement with one cross wire within the
critical section to the end of wire shall be computed as development length. ASTM A497M for welded deformed
the product of ld , from 12.2.2 or 12.2.3, times welded wire reinforcement requires the same strength of the weld as
deformed wire reinforcement factor, ψw , from 12.7.2 or required for welded plain wire reinforcement (ASTM A185M).
12.7.3. It shall be permitted to reduce ld in accordance Some of the development is assigned to welds and some
with 12.2.5 when applicable, but ld shall not be less than assigned to the length of deformed wire. The development
200 mm except in computation of lap splices by 12.18. computations are simplified from earlier Code provisions for
When using ψw from 12.7.2, it shall be permitted to use
an epoxy-coating factor ψe of 1.0 for epoxy-coated
welded deformed wire reinforcement in 12.2.2 and 12.2.3.
CODE COMMENTARY
and wire development by assuming that only one cross wire is
contained in the development length. The welded deformed
5d b⎞ wire reinforcement factor, ψw, in 12.7.2 is applied to the
⎛ ---------
⎝ s -⎠ deformed wire development length computed from 12.2. The
factor ψw was derived using the general relationships between
welded deformed wire reinforcement and deformed wires in
but not greater than 1.0, where s is the spacing
the ldb values of the 1983 Code.
between the wires to be developed.
Tests12.18 have indicated that epoxy-coated welded wire
12.7.3 — For welded deformed wire reinforcement
reinforcement has essentially the same development and
with no cross wires within ld or with a single cross wire
splice strengths as uncoated welded wire reinforcement
less than 50 mm from the point of the critical section,
because the cross wires provide the primary anchorage for
ψw shall be taken as 1.0, and ld shall be determined
the wire. Therefore, an epoxy-coating factor of 1.0 is used
as for deformed wire.
for development and splice lengths of epoxy-coated welded
wire reinforcement with cross wires within the splice or
12.7.4 — Where any plain wires, or deformed wires
development length.
larger than D-31, are present in the welded deformed
wire reinforcement in the direction of the development
Deformed wire larger than D-31 is treated as plain wire
length, the reinforcement shall be developed in accor-
because tests show that D-45 wire will achieve only approx-
dance with 12.8.
imately 60 percent of the bond strength in tension given by
Eq. (12-1).12.19
12
12.8—Development of welded plain wire R12.8 — Development of welded plain wire
reinforcement in tension reinforcement in tension
Yield strength of welded plain wire reinforcement shall Figure R12.8 shows the development requirements for
be considered developed by embedment of two cross welded plain wire reinforcement with development primarily
wires with the closer cross wire not less than 50 mm dependent on the location of cross wires. For welded plain
from the point of the critical section. However, ld shall wire reinforcement made with the smaller wires, an
not be less than embedment of at least two cross wires 50 mm or more
beyond the point of critical section is adequate to develop
A fy the full yield strength of the anchored wires. However, for
l d = 3.3 ------b- -------------
- (12-3) welded plain wire reinforcement made with larger closely
s λ f′
c spaced wires, a longer embedment is required and a minimum
development length is provided for this reinforcement.
where ld is measured from the point of the critical
section to the outermost crosswire, s is the spacing
between the wires to be developed, and λ as given in
12.2.4(d). Where reinforcement provided is in excess
of that required, ld may be reduced in accordance with
12.2.5. Length, ld , shall not be less than 150 mm
except in computation of lap splices by 12.19.
CODE COMMENTARY
12.9 — Development of prestressing strand R12.9 — Development of prestressing strand
12.9.1 — Except as provided in 12.9.1.1, seven-wire The development requirements for prestressing strand are
strand shall be bonded beyond the critical section, a intended to provide bond integrity for the strength of the
distance not less than member. The provisions are based on tests performed on
normalweight concrete members with a minimum cover of
f se⎞ f –f 50 mm. These tests may not represent the behavior of strand
l d = ⎛ ------- d + ⎛ ps se-⎞ d b (12-4)
⎝ 21 ⎠ b ⎝ ---------------------
7 ⎠ in low water-cementitious material ratio, no-slump,
concrete. Fabrication methods should ensure consolidation
of concrete around the strand with complete contact
The expressions in parentheses are used as constants
between the steel and concrete. Extra precautions should be
without units.
exercised when low water-cementitious material ratio, no-
slump concrete is used.
12.9.1.1 — Embedment less than ld shall be R12.9.1.1 — Figure R12.9 shows the relationship between
permitted at a section of a member provided the steel stress and the distance over which the strand is bonded
design strand stress at that section does not exceed to the concrete represented by Eq. (12-4). This idealized
values obtained from the bilinear relationship defined variation of strand stress may be used for analyzing sections
by Eq. (12-4). within the development region.12.22,12.23 The expressions for
transfer length, and for the additional bonded length neces-
sary to develop an increase in stress of (fps – fse), are based on
tests of members prestressed with clean, 6.4, 9.5, and 12.7 mm
diameter strands for which the maximum value of fps was
1900 MPa. See References 12.24, 12.25, and 12.26.
CODE COMMENTARY
12.9.2 — Limiting the investigation to cross sections R12.9.2 — Where bonding of one or more strands does not
nearest each end of the member that are required to extend to the end of the member, critical sections may be at
develop full design strength under specified factored locations other than where full design strength is required to
loads shall be permitted except where bonding of one be developed, and detailed analysis may be required.
or more strands does not extend to the end of the References 12.22 and 12.23 show a method that may be
member, or where concentrated loads are applied used in the case of strands with different points of full
within the strand development length. development. Conservatively, only the strands that are fully
developed at a section may be considered effective at that
section. If critical sections occur in the transfer region,
additional considerations may be necessary. Some loading
conditions, such as where heavy concentrated loads occur
within the strand development length, may cause critical
sections to occur away from the section that is required to
develop full design strength.
12.9.3 — Where bonding of a strand does not extend to R12.9.3 — Exploratory tests conducted in 196512.24 that
end of member, and design includes tension at service study the effect of debonded strand (bond not permitted to
load in precompressed tensile zone as permitted by extend to the ends of members) on performance of
18.4.2, ld specified in 12.9.1 shall be doubled. pretensioned girders indicated that the performance of these
girders with embedment lengths twice those required by
12.9.1 closely matched the flexural performance of similar
pretensioned girders with strand fully bonded to ends of
girders. Accordingly, doubled development length is
required for strand not bonded through to the end of a
member. Subsequent tests12.27 indicated that in pretensioned
members designed for zero tension in the concrete under
service load conditions (see 18.4.2), the development length
for debonded strands need not be doubled. For analysis of
sections with debonded strands at locations where strand is
not fully developed, it is usually assumed that both the
transfer length and development length are doubled.
CODE COMMENTARY
12.10 — Development of flexural R12.10 — Development of flexural
reinforcement — General reinforcement — General
12.10.2 — Critical sections for development of reinforce- R12.10.2 — Critical sections for a typical continuous beam
ment in flexural members are at points of maximum are indicated with a “c” or an “x” in Fig. R12.10.2. For
stress and at points within the span where adjacent uniform loading, the positive reinforcement extending into
reinforcement terminates, or is bent. Provisions of the support is more apt to be governed by the requirements
12.11.3 must be satisfied. of 12.11.3 rather than by development length measured
from a point of maximum moment or bar cutoff.
12.10.3 — Reinforcement shall extend beyond the R12.10.3 — The moment diagrams customarily used in
point at which it is no longer required to resist flexure design are approximate; some shifting of the location of
for a distance equal to d or 12db , whichever is greater, maximum moments may occur due to changes in loading,
except at supports of simple spans and at free end of settlement of supports, lateral loads, or other causes. A
cantilevers. diagonal tension crack in a flexural member without stirrups
may shift the location of the calculated tensile stress
12
approximately a distance d toward a point of zero moment.
When stirrups are provided, this effect is less severe,
although still present to some extent.
CODE COMMENTARY
To provide for shifts in the location of maximum moments,
the Code requires the extension of reinforcement a distance
d or 12db beyond the point at which it is theoretically no
longer required to resist flexure, except as noted.
12.10.4 — Continuing reinforcement shall have an R12.10.4 — Peak stresses exist in the remaining bars wherever
embedment length not less than ld beyond the point adjacent bars are cut off, or bent, in tension regions. In
where bent or terminated tension reinforcement is no Fig. R12.10.2, an “x” is used to indicate the peak stress
longer required to resist flexure. points remaining in continuing bars after part of the bars
have been cut off. If bars are cut off as short as the moment
diagrams allow, these peak stresses become the full fy,
which requires a full ld extension as indicated. This extension 12
may exceed the length required for flexure.
12.10.5 — Flexural reinforcement shall not be termi- R12.10.5 — Reduced shear strength and loss of ductility
nated in a tension zone unless 12.10.5.1, 12.10.5.2, or when bars are cut off in a tension zone, as in Fig. R12.10.2,
12.10.5.3 is satisfied. have been reported. The Code does not permit flexural
reinforcement to be terminated in a tension zone unless
12.10.5.1 — Vu at the cutoff point does not exceed additional conditions are satisfied. Flexure cracks tend to
(2/3)φVn . open early wherever any reinforcement is terminated in a
tension zone. If the steel stress in the continuing reinforcement
12.10.5.2 — Stirrup area in excess of that required and the shear strength are each near their limiting values,
for shear and torsion is provided along each termi- diagonal tension cracking tends to develop prematurely
nated bar or wire over a distance (3/4)d from the termi- from these flexure cracks. Diagonal cracks are less likely to
nation point. Excess stirrup area shall be not less than form where shear stress is low (see 12.10.5.1). Diagonal
0.41bw s/fyt . Spacing s shall not exceed d/(8βb). cracks can be restrained by closely spaced stirrups (see
12.10.5.2). A lower steel stress reduces the probability of
12.10.5.3 — For No. 36 bars and smaller, such diagonal cracking (see 12.10.5.3). These requirements
continuing reinforcement provides double the area are not intended to apply to tension splices that are covered
required for flexure at the cutoff point and Vu does not by 12.2, 12.13.5, and the related 12.15.
exceed (3/4)φVn .
12.10.6 — Adequate anchorage shall be provided for R12.10.6 — Brackets, members of variable depth, and other
tension reinforcement in flexural members where members where fs, calculated stress in reinforcement at
reinforcement stress is not directly proportional to service loads, does not decrease linearly in proportion to a
moment, such as: sloped, stepped, or tapered footings; decreasing moment, require additional consideration for
brackets; deep flexural members; or members in which proper development of the flexural reinforcement. For the
tension reinforcement is not parallel to compression face. bracket shown in Fig. R12.10.6, the stress at ultimate in the
See 12.11.4 and 12.12.4 for deep flexural members. reinforcement is almost constant at approximately fy from
the face of support to the load point. In such a case, develop-
ment of the flexural reinforcement depends largely on the
end anchorage provided at the loaded end. Reference 12.1
suggests a welded cross bar of equal diameter as a means of
providing effective end anchorage. An end hook in the
vertical plane, with the minimum diameter bend, is not
totally effective because an essentially plain concrete corner
CODE COMMENTARY
will exist near loads applied close to the corner. For wide
12 brackets (perpendicular to the plane of the figure) and loads
not applied close to the corners, U-shaped bars in a hori-
zontal plane provide effective end hooks.
12.11.1 — At least one-third the positive moment R12.11.1 — Positive moment reinforcement is carried into
reinforcement in simple members and one-fourth the the support to provide for some shifting of the moments due
positive moment reinforcement in continuous to changes in loading, settlement of supports, and lateral
members shall extend along the same face of member loads.
into the support. In beams, such reinforcement shall
extend into the support at least 150 mm.
12.11.2 — When a flexural member is part of a R12.11.2 — When a flexural member is part of a primary
primary seismic-load-resisting system, positive moment seismic-load-resisting system, loads greater than those
reinforcement required to be extended into the support anticipated in design may cause reversal of moment at
by 12.11.1 shall be anchored to develop fy in tension supports; some positive reinforcement should be well
at the face of support. anchored into the support. This anchorage is required to
ensure ductility of response in the event of serious over-
stress, such as from blast or earthquake. It is not sufficient to
use more reinforcement at lower stresses.
12.11.3 — At simple supports and at points of inflection, R12.11.3 — At simple supports and points of inflection
positive moment tension reinforcement shall be limited such as “P.I.” in Fig. R12.10.2, the diameter of the positive
to a diameter such that ld computed for fy by 12.2 reinforcement should be small enough so that computed
satisfies Eq. (12-5); except, Eq. (12-5) need not be development length of the bar ld does not exceed Mn /Vu +
satisfied for reinforcement terminating beyond center- la, or under favorable support conditions, 1.3Mn / Vu + la.
line of simple supports by a standard hook, or a Figure R12.11.3(a) illustrates the use of the provision.
mechanical anchorage at least equivalent to a standard
hook. At the point of inflection, the value of la should not exceed
the actual bar extension used beyond the point of zero
M moment. The Mn /Vu portion of the available length is a
l d ≤ -------n- + l a (12-5) theoretical quantity not generally associated with an
Vu
obvious maximum stress point. Mn is the nominal flexural
CODE COMMENTARY
where: strength of the cross section without the φ-factor and is not
Mn is calculated assuming all reinforcement at the the applied factored moment.
section to be stressed to fy;
Vu is calculated at the section; The length Mn /Vu corresponds to the development length
la at a support shall be the embedment length beyond for the maximum size bar obtained from the previously used
center of support; or flexural bond equation Σo = V/ujd, where u is bond stress,
la at a point of inflection shall be limited to d or 12db , and jd is the moment arm. In the 1971 Code, this anchorage
whichever is greater. requirement was relaxed from previous Codes by crediting
An increase of 30 percent in the value of Mn /Vu shall the available end anchorage length la and by including a
be permitted when the ends of reinforcement are 30 percent increase for Mn /Vu when the ends of the reinforce-
confined by a compressive reaction. ment are confined by a compressive reaction.
CODE COMMENTARY
data are not available to show that a long end anchorage
length will be fully effective in developing a bar that has
only a short length between a point of inflection and a point
of maximum stress.
12.11.4 — At simple supports of deep beams, positive R12.11.4 — The use of the strut-and-tie model for the
moment tension reinforcement shall be anchored to design of reinforced concrete deep flexural members clari-
develop fy in tension at the face of the support except fies that there is significant tension in the reinforcement at
that if design is carried out using Appendix A, the positive the face of the support. This requires the tension reinforce-
moment tension reinforcement shall be anchored in ment to be continuous or be developed through and beyond
accordance with A.4.3. At interior supports of deep the support.12.28
beams, positive moment tension reinforcement shall
be continuous or be spliced with that of the adjacent
spans.
12.12.1 — Negative moment reinforcement in a Figure R12.12 illustrates two methods of satisfying
continuous, restrained, or cantilever member, or in any requirements for anchorage of tension reinforcement
member of a rigid frame, shall be anchored in or beyond the face of support. For anchorage of reinforcement
12
through the supporting member by embedment length, with hooks, see R12.5.
hooks, or mechanical anchorage.
Section 12.12.3 provides for possible shifting of the
12.12.2 — Negative moment reinforcement shall have moment diagram at a point of inflection, as discussed under
an embedment length into the span as required by R12.10.3. This requirement may exceed that of 12.10.3, and
12.1 and 12.10.3. the more restrictive of the two provisions governs.
12.13.1 — Web reinforcement shall be as close to the R12.13.1 — Stirrups should be carried as close to the
compression and tension surfaces of the member as compression face of the member as possible because near
cover requirements and proximity of other reinforce- ultimate load the flexural tension cracks penetrate deeply.
ment permits.
12.13.2 — Ends of single leg, simple U-, or multiple U- R12.13.2 — The anchorage or development requirements
stirrups shall be anchored as required by 12.13.2.1 for stirrups composed of bars or deformed wire were
through 12.13.2.5. changed in the 1989 Code to simplify the requirements. The
straight anchorage was deleted as this stirrup is difficult to
hold in place during concrete placement and the lack of a
hook may make the stirrup ineffective as it crosses shear
cracks near the end of the stirrup.
CODE COMMENTARY
12
12.13.2.1 — For No. 16 bar and MD200 wire, and R12.13.2.1 — For a No. 16 bar or smaller, anchorage is
smaller, and for No. 19, No. 22, and No. 25 bars with provided by a standard stirrup hook, as defined in 7.1.3,
fyt of 280 MPa or less, a standard hook around longitu- hooked around a longitudinal bar. The 1989 Code eliminated
dinal reinforcement. the need for a calculated straight embedment length in addition
to the hook for these small bars, but 12.13.1 requires a full-
depth stirrup. Likewise, larger stirrups with fyt equal to or
less than 280 MPa are sufficiently anchored with a standard
stirrup hook around the longitudinal reinforcement.
12.13.2.2 — For No. 19, No. 22, and No. 25 stirrups R12.13.2.2 — Since it is not possible to bend a No. 19,
with fyt greater than 280 MPa, a standard stirrup hook No. 22, or No. 25 stirrup tightly around a longitudinal bar
around a longitudinal bar plus an embedment between and due to the force in a bar with a design stress greater than
midheight of the member and the outside end of the 280 MPa, stirrup anchorage depends on both the value of the
hook equal to or greater than 0.17dbfyt /(λ f c′ ). hook and whatever development length is provided. A
CODE COMMENTARY
longitudinal bar within a stirrup hook limits the width of any
flexural cracks, even in a tensile zone. Since such a stirrup hook
cannot fail by splitting parallel to the plane of the hooked
bar, the hook strength as utilized in 12.5.2 has been adjusted
to reflect cover and confinement around the stirrup hook.
12.13.2.3 — For each leg of welded plain wire R12.13.2.3 — The requirements for anchorage of
reinforcement forming simple U-stirrups, either: welded plain wire reinforcement stirrups are illustrated
in Fig. R12.13.2.3.
(a) Two longitudinal wires spaced at a 50 mm
spacing along the member at the top of the U; or
12.13.2.4 — For each end of a single leg stirrup of R12.13.2.4 — Use of welded wire reinforcement for
welded wire reinforcement, two longitudinal wires at a shear reinforcement has become commonplace in the
minimum spacing of 50 mm and with the inner wire at precast, prestressed concrete industry. The rationale for
least the greater of d/4 or 50 mm from d/2. Outer acceptance of straight sheets of welded wire reinforcement
longitudinal wire at tension face shall not be farther as shear reinforcement is presented in a report by a joint
from the face than the portion of primary flexural rein- PCI/WRI Ad Hoc Committee on Welded Wire Fabric for
forcement closest to the face. Shear Reinforcement.12.29
CODE COMMENTARY
12.13.2.5 — In joist construction as defined in 8.11, R12.13.2.5 — In joists, a small bar or wire can be
for No. 13 bar and MD130 wire and smaller, a standard anchored by a standard hook not engaging longitudinal
hook. reinforcement, allowing a continuously bent bar to form a
series of single-leg stirrups in the joist.
12.13.5 — Pairs of U-stirrups or ties so placed as to R12.13.5 — These requirements for lapping of double
form a closed unit shall be considered properly spliced U-stirrups to form closed stirrups control over the provisions
when length of laps are 1.3ld. In members at least of 12.15.
450 mm deep, such splices with Abfyt not more than
40 kN per leg shall be considered adequate if stirrup
legs extend the full available depth of member.
CODE COMMENTARY
12.14 — Splices of reinforcement — General R12.14 — Splices of reinforcement — General
12.14.1 — Splices of reinforcement shall be made only Splices should, if possible, be located away from points of
as required or permitted on design drawings, or in maximum tensile stress. The lap splice requirements of
specifications, or as authorized by the licensed design 12.15 encourage this practice.
professional.
12.14.2.1 — Lap splices shall not be used for bars R12.14.2.1 — Because of lack of adequate experimental
larger than No. 36 except as provided in 12.16.2 and data on lap splices of No. 43 and No. 57 bars in compression
15.8.2.3. and in tension, lap splicing of these bar sizes is prohibited
except as permitted in 12.16.2 and 15.8.2.3 for compression
lap splices of No. 43 and No. 57 bars with smaller bars.
12.14.2.2 — Lap splices of bars in a bundle shall be R12.14.2.2 — The increased length of lap required for
based on the lap splice length required for individual bars in bundles is based on the reduction in the exposed
bars within the bundle, increased in accordance with perimeter of the bars. Only individual bars are lap spliced
12.4. Individual bar splices within a bundle shall not along the bundle.
overlap. Entire bundles shall not be lap spliced.
12 12.14.2.3 — Bars spliced by noncontact lap splices R12.14.2.3 — If individual bars in noncontact lap splices
in flexural members shall not be spaced transversely are too widely spaced, an unreinforced section is created.
farther apart than the smaller of one-fifth the required Forcing a potential crack to follow a zigzag line (5-to-1
lap splice length, and 150 mm. slope) is considered a minimum precaution. The 150 mm
maximum spacing is added because most research available
on the lap splicing of deformed bars was conducted with
reinforcement within this spacing.
12.14.3 — Mechanical and welded splices R12.14.3 — Mechanical and welded splices
12.14.3.2 — A full mechanical splice shall develop in R12.14.3.2 — The maximum reinforcement stress used in
tension or compression, as required, at least 1.25fy of design under the Code is the specified yield strength. To
the bar. ensure sufficient strength in splices so that yielding can be
achieved in a member and thus brittle failure avoided, the
25 percent increase above the specified yield strength was
selected as both an adequate minimum for safety and a
practicable maximum for economy.
12.14.3.3 — Except as provided in this Code, all R12.14.3.3 — See R3.5.2 for discussion on welding.
welding shall conform to “Structural Welding Code—
Reinforcing Steel” (AWS D1.4).
12.14.3.4 — A full welded splice shall develop at R12.14.3.4 — A full welded splice is primarily intended
least 1.25fy of the bar. for large bars (No. 19 and larger) in main members. The
tensile strength requirement of 125 percent of specified
yield strength is intended to provide sound welding that is
also adequate for compression. See the discussion on strength
in R12.14.3.2. The 1995 Code eliminated a requirement that
the bars be butted since indirect butt welds are permitted by
AWS D1.4, although AWS D1.4 does indicate that wherever
practical, direct butt splices are preferable for No. 22 bars
and larger.
CODE COMMENTARY
12.14.3.5 — Mechanical or welded splices not R12.14.3.5 — The use of mechanical or welded splices of
meeting requirements of 12.14.3.2 or 12.14.3.4 shall less strength than 125 percent of specified yield strength is
be permitted only for No. 16 bars and smaller and in permitted if the minimum design criteria of 12.15.5 are met.
accordance with 12.15.5. Therefore, lap welds of reinforcing bars, either with or
without backup material, welds to plate connections, and
end-bearing splices are allowed under certain conditions.
The 1995 Code limited these lower strength welds and
connections to No. 16 bars and smaller due to the poten-
tially brittle nature of failure at these welds.
12.15 — Splices of deformed bars and R12.15 — Splices of deformed bars and
deformed wire in tension deformed wire in tension
12.15.1 — Minimum length of lap for tension lap R12.15.1 — Lap splices in tension are classified as Type A
splices shall be as required for Class A or B splice, but or B, with length of lap a multiple of the tensile development
not less than 300 mm, where: length ld calculated in accordance with 12.2.2 or 12.2.3. The
development length ld used to obtain lap length should be
Class A splice................................................... 1.0ld based on fy because the splice classifications already reflect
any excess reinforcement at the splice location; therefore,
Class B splice................................................... 1.3ld the factor from 12.2.5 for excess As should not be used.
where ld is calculated in accordance with 12.2 to When multiple bars located in the same plane are spliced at
12
develop fy, but without the 300 mm minimum of 12.2.1 the same section, the clear spacing is the minimum clear
and without the modification factor of 12.2.5. distance between the adjacent splices. For splices in
columns with offset bars, Fig. R12.15.1(a) illustrates the
clear spacing to be used. For staggered splices, the clear
spacing is taken as the minimum distance between adjacent
splices [Fig. R12.15.1(b)].
CODE COMMENTARY
The 1989 Code contained several changes in development
length in tension that eliminated many of the concerns
regarding tension splices due to closely spaced bars with
minimal cover. Thus, the Class C splice was eliminated
although development lengths, on which splice lengths are
based, have in some cases increased. Committee 318
considered suggestions from many sources, including ACI
Committee 408, but has retained a two-level splice length
primarily to encourage splicing bars at points of minimum
stress and staggering splices to improve behavior of critical
details.
12.15.2 — Lap splices of deformed bars and deformed R12.15.2 — The tension lap splice requirements of 12.15.1
wire in tension shall be Class B splices except that encourage the location of splices away from regions of high
Class A splices are allowed when: tensile stress to locations where the area of steel provided is
at least twice that required by analysis. Table R12.15.2
(a) the area of reinforcement provided is at least presents the splice requirements in tabular form as presented
twice that required by analysis over the entire length in earlier Code editions.
of the splice; and
(b) one-half or less of the total reinforcement is
12 spliced within the required lap length.
12.15.4 — Mechanical or welded splices used where R12.15.4 — A mechanical or welded splice should develop
area of reinforcement provided is less than twice that at least 125 percent of the specified yield strength when
required by analysis shall meet requirements of located in regions of high tensile stress in the reinforcement.
12.14.3.2 or 12.14.3.4. Such splices need not be staggered, although such staggering
is encouraged where the area of reinforcement provided is
less than twice that required by the analysis.
12.15.5 — Mechanical or welded splices not meeting R12.15.5 — See R12.14.3.5. Section 12.15.5 concerns the
the requirements of 12.14.3.2 or 12.14.3.4 shall be situation where mechanical or welded splices of strength less
permitted for No. 16 bars and smaller if the require- than 125 percent of the specified yield strength of the rein-
ments of 12.15.5.1 through 12.15.5.3 are met: forcement may be used. It provides a relaxation in the splice
requirements where the splices are staggered and excess
12.15.5.1 — Splices shall be staggered at least reinforcement area is available. The criterion of twice the
600 mm. computed tensile force is used to cover sections containing
partial tensile splices with various percentages of total
12.15.5.2 — In computing the tensile forces that can continuous steel. The usual partial tensile splice is a flare
be developed at each section, the spliced reinforce- groove weld between bars or bar and structural steel piece.
ment stress shall be taken as the specified splice
strength, but not greater than fy . The stress in the To detail such welding, the length of weld should be specified.
unspliced reinforcement shall be taken as fy times the Such welds are rated at the product of total weld length
ratio of the shortest length embedded beyond the
section to ld , but not greater than fy . TABLE R12.15.2 — TENSION LAP SPLICES
Maximum percent of As spliced within
12.15.5.3 — The total tensile force that can be A s provided* required lap length
---------------------------------
developed at each section must be at least twice that A s required 50 100
required by analysis, and at least 140 MPa times the Equal to or greater than 2 Class A Class B
total area of reinforcement provided. Less than 2 Class B Class B
*Ratio of area of reinforcement provided to area of reinforcement required by analysis at
splice locations.
CODE COMMENTARY
times effective size of groove weld (established by bar size)
times allowable stress permitted by “Structural Welding
Code—Reinforcing Steel” (AWS D1.4).
12.15.6 — Splices in tension tie members shall be R12.15.6 — A tension tie member has the following charac-
made with a full mechanical or full welded splice in teristics: member having an axial tensile force sufficient to
accordance with 12.14.3.2 or 12.14.3.4 and splices in create tension over the cross section; a level of stress in the
adjacent bars shall be staggered at least 750 mm. reinforcement such that every bar must be fully effective;
and limited concrete cover on all sides. Examples of
members that may be classified as tension ties are arch ties,
hangers carrying load to an overhead supporting structure,
and main tension elements in a truss.
12.16.1 — Compression lap splice length shall be R12.16.1 — Essentially, lap requirements for compression
0.071fy db , for fy of 420 MPa or less, or (0.13fy – splices have remained the same since the 1963 Code.
24)db for fy greater than 420 MPa, but not less than
300 mm. For fc′ less than 21 MPa, length of lap shall The 1963 Code values were modified in the 1971 Code to
be increased by one-third. recognize various degrees of confinement and to permit
design with reinforcement having a specified yield strength
up to 550 MPa. Tests12.1,12.30 have shown that splice
strengths in compression depend considerably on end
bearing and do not increase proportionally in strength when
the splice length is doubled. Accordingly, for specified yield
strengths above 420 MPa, compression lap lengths are
significantly increased, except where spiral enclosures are
used (as in spiral columns) the where the increase is about
10 percent for an increase in specified yield strength from
420 to 520 MPa.
CODE COMMENTARY
12.16.2 — When bars of different size are lap spliced R12.16.2 — The lap splice length is to be computed based
in compression, splice length shall be the larger of ldc on the larger of the compression splice length of the smaller
of larger bar and compression lap splice length of bar; or the compression development length of the larger
smaller bar. Lap splices of No. 43 and No. 57 bars to bar. Lap splices are generally prohibited for No. 43 or
No. 36 and smaller bars shall be permitted. No. 57 bars; however, for compression only, lap splices are
permitted for No. 43 or No. 57 bars to No. 36 or smaller bars.
12.16.4.1 — In bars required for compression only, R12.16.4.1 — Experience with end-bearing splices has
transmission of compressive stress by bearing of been almost exclusively with vertical bars in columns. If
square cut ends held in concentric contact by a suitable bars are significantly inclined from the vertical, attention is
device shall be permitted. required to ensure that adequate end-bearing contact can be
achieved and maintained.
12.16.4.2 — Bar ends shall terminate in flat surfaces R12.16.4.2 — These tolerances were added in the 1971
within 1.5 degrees of a right angle to the axis of the Code, representing practice based on tests of full-size
12 bars and shall be fitted within 3 degrees of full bearing members containing No. 57 bars.
after assembly.
12.16.4.3 — End-bearing splices shall be used only R12.16.4.3 — This limitation was added in the 1971
in members containing closed ties, closed stirrups, or Code to ensure a minimum shear resistance in sections
spirals. containing end-bearing splices.
12.17 — Splice requirements for columns R12.17 — Splice requirements for columns
12.17.1 — Lap splices, mechanical splices, butt- In columns subject to flexure and axial loads, tension
welded splices, and end-bearing splices shall be used stresses may occur on one face of the column for moderate
with the limitations of 12.17.2 through 12.17.4. A splice and large eccentricities as shown in Fig. R12.17. When such
shall satisfy requirements for all load combinations for tensions occur, 12.17 requires tension splices to be used or
the column. an adequate tensile resistance to be provided. Furthermore,
a minimum tension strength is required in each face of all
columns even where analysis indicates compression only.
CODE COMMENTARY
The 1989 Code clarifies this section on the basis that a
compressive lap splice has a tension strength of at least one-
quarter fy, which simplifies the calculation requirements in
previous Codes.
12.17.2.1 — Where the bar stress due to factored R12.17.2.1 — The 1989 Code was simplified for column
loads is compressive, lap splices shall conform to bars always in compression on the basis that a compressive
12.16.1, 12.16.2, and, where applicable, to 12.17.2.4 lap splice is adequate for sufficient tension to preclude
or 12.17.2.5. special requirements.
12.17.2.4 — In tied reinforced compression R12.17.2.4 — Reduced lap lengths are allowed when the
members, where ties throughout the lap splice length splice is enclosed throughout its length by minimum ties.
have an effective area not less than 0.0015hs in both
directions, lap splice length shall be permitted to be The tie legs perpendicular to each direction are computed
multiplied by 0.83, but lap length shall not be less than separately and the requirement satisfied in each direction
300 mm. Tie legs perpendicular to dimension h shall to apply the 0.83 reduction factor. This is illustrated in
be used in determining effective area. Fig. R12.17.2, where four legs are effective in one direction
and two legs in the other direction. This calculation is
critical in one direction, which normally can be determined
by inspection.
12.17.2.5 — In spirally reinforced compression R12.17.2.5 — Compression lap lengths may be reduced
members, lap splice length of bars within a spiral shall when the lap splice is enclosed throughout its length by
be permitted to be multiplied by 0.75, but lap length spirals because of increased splitting resistance. Spirals
shall not be less than 300 mm. should meet requirements of 7.10.4 and 10.9.3.
12.17.3 — Mechanical or welded splices in columns R12.17.3 — Mechanical or welded splices in columns
Mechanical or welded splices in columns shall meet Mechanical or welded splices are allowed for splices in
the requirements of 12.14.3.2 or 12.14.3.4. columns but should be designed as a full mechanical splice
or a full welded splice developing 125 percent fy as required
by 12.14.3.2 or 12.14.3.4. Splice strength is traditionally
tested in tension and full strength is required to reflect the
high compression loads possible in column reinforcement
CODE COMMENTARY
End-bearing splices complying with 12.16.4 shall be End-bearing splices used to splice column bars always in
permitted to be used for column bars stressed in compression should have a tension strength of 25 percent of
compression provided the splices are staggered or the specified yield strength of the steel area on each face of
additional bars are provided at splice locations. The the column, either by staggering the end-bearing splices or
continuing bars in each face of the column shall have a by adding additional steel through the splice location. The
tensile strength, based on fy , not less than 0.25fy times end-bearing splice should conform to 12.16.4.
the area of the vertical reinforcement in that face.
12.18 — Splices of welded deformed wire R12.18 — Splices of welded deformed wire
reinforcement in tension reinforcement in tension
12.18.1 — Minimum lap splice length of welded Splice provisions for welded deformed wire reinforcement
deformed wire reinforcement measured between the are based on available tests.12.31 The requirements were
ends of each reinforcement sheet shall be not less simplified (1976 Code supplement) from provisions of the
than the larger of 1.3ld and 200 mm, and the overlap 1971 Code by assuming that only one cross wire of each
measured between outermost cross wires of each welded wire reinforcement sheet is overlapped and by
reinforcement sheet shall be not less than 50 mm, where computing the splice length as 1.3ld . The development
ld is calculated in accordance with 12.7 to develop fy . length ld is that computed in accordance with the provisions
of 12.7 without regard to the 200 mm minimum. The 8 in.
12.18.2 — Lap splices of welded deformed wire applies to the overall splice length. See Fig. R12.18. If no
reinforcement, with no cross wires within the lap splice cross wires are within the lap length, the provisions for
length, shall be determined as for deformed wire. deformed wire apply.
12.18.3 — Where any plain wires, or deformed wires Deformed wire larger than MD200 is treated as plain wire
larger than MD200, are present in the welded deformed because tests show that MD290 wire will achieve only
wire reinforcement in the direction of the lap splice or approximately 60 percent of the bond strength in tension
where welded deformed wire reinforcement is lap given by Eq. (21-1).12.19
spliced to welded plain wire reinforcement, the rein-
forcement shall be lap spliced in accordance with 12.19.
CODE COMMENTARY
12.19 — Splices of welded plain wire R12.19 — Splices of welded plain wire
reinforcement in tension reinforcement in tension
Minimum length of lap for lap splices of welded plain The strength of lap splices of welded plain wire reinforce-
wire reinforcement shall be in accordance with 12.19.1 ment is dependent primarily on the anchorage obtained
and 12.19.2. from the cross wires rather than on the length of wire in the
splice. For this reason, the lap is specified in terms of
12.19.1 — Where As provided is less than twice that overlap of cross wires rather than in wire diameters or
required by analysis at splice location, length of inches. The 50 mm additional lap required is to assure
overlap measured between outermost cross wires of overlapping of the cross wires and to provide space for satis-
each reinforcement sheet shall be not less than the factory consolidation of the concrete between cross wires.
largest of one spacing of cross wires plus 50 mm, Research12.32 has shown an increased splice length is
1.5ld, and 150 mm, where ld is calculated in accor- required when welded wire reinforcement of large, closely
dance with 12.8 to develop fy . spaced wires is lapped and, as a consequence, additional
splice length requirements are provided for this reinforce-
12.19.2 — Where As provided is at least twice that ment in addition to an absolute minimum of 150 mm. The
required by analysis at splice location, length of development length ld is that computed in accordance with
overlap measured between outermost cross wires of the provisions of 12.8 without regard to the 150 mm
each reinforcement sheet shall not be less than the minimum. Splice requirements are illustrated in Fig. R12.19.
larger of 1.5ld , and 50 mm, where ld is calculated in
accordance with 12.8 to develop fy .
12
12
CODE COMMENTARY
13.1 — Scope R13.1 — Scope
13.1.1 — Provisions of Chapter 13 shall apply for The design methods given in Chapter 13 are based on analysis
design of slab systems reinforced for flexure in more of the results of an extensive series of tests13.1-13.7 and the
than one direction, with or without beams between well-established performance record of various slab
supports. systems. Much of Chapter 13 is concerned with the selection
and distribution of flexural reinforcement. Safety of a slab
13.1.2 — For a slab system supported by columns or system requires consideration of the transmission of load
walls, dimensions c1, c2, and ln shall be based on an from the slab to the columns by flexure, torsion, and shear.
effective support area defined by the intersection of Design criteria for shear and torsion in slabs are given in
the bottom surface of the slab, or of the drop panel or Chapter 11.
shear cap if present, with the largest right circular
cone, right pyramid, or tapered wedge whose surfaces The fundamental design principles contained in Chapter 13
are located within the column and the capital or are applicable to all planar structural systems subjected to
bracket and are oriented no greater than 45 degrees to transverse loads. Some of the specific design rules, as well
the axis of the column. as historical precedents, limit the types of structures to
which Chapter 13 applies. General characteristics of slab
13.1.3 — Solid slabs and slabs with recesses or systems that may be designed according to Chapter 13 are
pockets made by permanent or removable fillers described in this section. These systems include flat slabs,
between ribs or joists in two directions are included flat plates, two-way slabs, and waffle slabs. Slabs with 13
within the scope of Chapter 13. paneled ceilings are two-way wide-band beam systems.
13.1.4 — Minimum thickness of slabs designed in True one-way slabs, slabs reinforced to resist flexural stresses
accordance with Chapter 13 shall be as required by in only one direction, are excluded. Also excluded are slabs-
9.5.3. on-ground that do not transmit vertical loads from other parts
of the structure to the soil.
CODE COMMENTARY
13.2 — General R13.2 — General
13.2.3 — A panel is bounded by column, beam, or wall R13.2.3 — A panel includes all flexural elements between
centerlines on all sides. column centerlines. Thus, the column strip includes the
beam, if any.
13.2.4 — For monolithic or fully composite construction, R13.2.4 — For monolithic or fully composite construction,
a beam includes that portion of slab on each side of the beams include portions of the slab as flanges. Two
the beam extending a distance equal to the projection examples of the rule are provided in Fig. R13.2.4.
of the beam above or below the slab, whichever is
greater, but not greater than four times the slab
thickness.
13.2.5 — When used to reduce the amount of negative R13.2.5-R13.2.6 — Drop panel dimensions specified in
moment reinforcement over a column or minimum 13.2.5 are necessary when reducing the amount of negative
13 required slab thickness, a drop panel shall: moment reinforcement following 13.3.7 or to satisfy some
minimum slab thicknesses permitted in 9.5.3. If the
(a) project below the slab at least one-quarter of the dimensions are less than specified in 13.2.5, the projection
adjacent slab thickness; and may be used as a shear cap to increase the shear strength of
(b) extend in each direction from the centerline of the slab. For slabs with changes in thickness it is necessary
support a distance not less than one-sixth the span to check the shear strength at several sections. See 11.11.1.2.
length measured from center-to-center of supports
in that direction.
CODE COMMENTARY
13.3 — Slab reinforcement R13.3 — Slab reinforcement
13.3.2 — Spacing of reinforcement at critical sections R13.3.2 — The requirement that the center-to-center
shall not exceed two times the slab thickness, except spacing of the reinforcement be not more than two times the
for portions of slab area of cellular or ribbed construction. slab thickness applies only to the reinforcement in solid
In the slab over cellular spaces, reinforcement shall be slabs, and not to reinforcement joists or waffle slabs. This
provided as required by 7.12. limitation is to ensure slab action, cracking, and provide for
the possibility of loads concentrated on small areas of the
slab. See also R10.6.
13.3.3 — Positive moment reinforcement perpendic- R13.3.3-R13.3.5 — Bending moments in slabs at spandrel
ular to a discontinuous edge shall extend to the edge beams can be subject to great variation. If spandrel beams are
of slab and have embedment, straight or hooked, at built solidly into walls, the slab approaches complete fixity.
least 150 mm in spandrel beams, columns, or walls. Without an integral wall, the slab could approach simply
supported, depending on the torsional rigidity of the spandrel
13.3.4 — Negative moment reinforcement perpendicular beam or slab edge. These requirements provide for unknown
to a discontinuous edge shall be bent, hooked, or conditions that might normally occur in a structure.
otherwise anchored in spandrel beams, columns, or
walls, and shall be developed at face of support 13
according to provisions of Chapter 12.
13.3.6 — At exterior corners of slabs supported by R13.3.6 — Unrestrained corners of two-way slabs tend to lift
edge walls or where one or more edge beams have a when loaded. If this lifting tendency is restrained by edge
value of αf greater than 1.0, top and bottom slab walls or beams, bending moments result in the slab. This
reinforcement shall be provided at exterior corners in section provides steel to resist these moments and control
accordance with 13.3.6.1 through 13.3.6.4. cracking. Reinforcement provided for flexure in the primary
directions may be used to satisfy this requirement. See
13.3.6.1 — Corner reinforcement in both top and Fig. R13.3.6.
bottom of slab shall be sufficient to resist a moment
per unit of width equal to the maximum positive
moment per unit width in the slab panel.
CODE COMMENTARY
Alternatively, reinforcement shall be placed in two
layers parallel to the sides of the slab in both the top
and bottom of the slab.
13
13.3.8 — Details of reinforcement in slabs without R13.3.8 — Details of reinforcement in slabs without
beams beams
13.3.8.1 — In addition to the other requirements of In the 1989 Code, bent bars were removed from Fig. 13.3.8.
13.3, reinforcement in slabs without beams shall have This was done because bent bars are seldom used and are
minimum extensions as prescribed in Fig. 13.3.8. difficult to place properly. Bent bars are permitted, however,
if they comply with 13.3.8.3. Refer to 13.4.8 of the 1983
13.3.8.2 — Where adjacent spans are unequal, Code.
extensions of negative moment reinforcement beyond
the face of support as prescribed in Fig. 13.3.8 shall
be based on requirements of the longer span.
CODE COMMENTARY
13
Fig. 13.3.8—Minimum extensions for reinforcement in slabs without beams. (See 12.11.1 for reinforcement extension
into supports).
13.3.8.4 — In frames where two-way slabs act as R13.3.8.4 — For moments resulting from combined
primary members resisting lateral loads, lengths of lateral and gravity loadings, the minimum lengths and
reinforcement shall be determined by analysis but extensions of bars in Fig. 13.3.8 may not be sufficient.
shall not be less than those prescribed in Fig. 13.3.8.
13.3.8.5 — All bottom bars or wires within the R13.3.8.5 — The continuous column strip bottom reinforce-
column strip, in each direction, shall be continuous or ment provides the slab some residual ability to span to the
spliced with Class B tension splices or with mechanical adjacent supports should a single support be damaged. The
or welded splices satisfying 12.14.3. Splices shall be two continuous column strip bottom bars or wires through
located as shown in Fig. 13.3.8. At least two of the the column may be termed “integrity steel,” and are
column strip bottom bars or wires in each direction provided to give the slab some residual strength following a
shall pass within the region bounded by the longitu- single punching shear failure at a single support.13.9 In the
dinal reinforcement of the column and shall be 2002 Code, mechanical and welded splices were explicitly
anchored at exterior supports. recognized as alternative methods of splicing reinforcement.
CODE COMMENTARY
13.3.8.6 — In slabs with shearheads and in lift-slab R13.3.8.6 — In the 1992 Code, this provision was added
construction where it is not practical to pass the to require the same integrity steel as for other two-way slabs
bottom bars required by 13.3.8.5 through the column, without beams in case of a punching shear failure at a
at least two bonded bottom bars or wires in each support.
direction shall pass through the shearhead or lifting
collar as close to the column as practicable and be In some instances, there is sufficient clearance so that the
continuous or spliced with a Class A splice. At exterior bonded bottom bars can pass under shearheads and through
columns, the reinforcement shall be anchored at the the column. Where clearance under the shearhead is
shearhead or lifting collar. inadequate, the bottom bars should pass through holes in
the shearhead arms or within the perimeter of the lifting
collar. Shearheads should be kept as low as possible in the
slab to increase their effectiveness.
13.5.1 — A slab system shall be designed by any proce- R13.5.1 — This section permits a design to be based
dure satisfying conditions of equilibrium and geometric directly on fundamental principles of structural mechanics,
compatibility, if shown that the design strength at every provided it can be demonstrated explicitly that all strength
section is at least equal to the required strength set and serviceability criteria are satisfied. The design of the
forth in 9.2 and 9.3, and that all serviceability condi- slab may be achieved through the combined use of classic
tions, including limits on deflections, are met. solutions based on a linearly elastic continuum, numerical
CODE COMMENTARY
solutions based on discrete elements, or yield-line analyses,
including, in all cases, evaluation of the stress conditions
around the supports in relation to shear and torsion as well
as flexure. The design of a slab system involves more than
its analysis, and any deviations in physical dimensions of
the slab from common practice should be justified on the
basis of knowledge of the expected loads and the reliability
of the calculated stresses and deformations of the structure.
13.5.1.1 — Design of a slab system for gravity loads, R13.5.1.1 — For gravity load analysis of two-way slab
including the slab and beams (if any) between systems, two analysis methods are given in 13.6 and 13.7.
supports and supporting columns or walls forming The specific provisions of both design methods are limited
orthogonal frames, by either the Direct Design Method in application to orthogonal frames subject to gravity loads
of 13.6 or the Equivalent Frame Method of 13.7, shall only. Both methods apply to two-way slabs with beams as
be permitted. well as to flat slabs and flat plates. In both methods, the
distribution of moments to the critical sections of the slab
reflects the effects of reduced stiffness of elements due to
cracking and support geometry.
13.5.1.2 — For lateral loads, analysis of frames shall R13.5.1.2 — During the life of a structure, construction
take into account effects of cracking and reinforcement loads, ordinary occupancy loads, anticipated overloads, and
on stiffness of frame members. volume changes will cause cracking of slabs. Cracking reduces
stiffness of slab members, and increases lateral flexibility when
lateral loads act on the structure. Cracking of slabs should be 13
considered in stiffness assumptions so that drift caused by
wind or earthquake is not grossly underestimated.
CODE COMMENTARY
13.5.2 — The slab and beams (if any) between
supports shall be proportioned for factored moments
prevailing at every section.
13.5.3 — When gravity load, wind, earthquake, or R13.5.3 — This section is concerned primarily with slab
other lateral forces cause transfer of moment between systems without beams. Tests and experience have shown
slab and column, a fraction of the unbalanced moment that, unless measures are taken to resist the torsional and
shall be transferred by flexure in accordance with shear stresses, all reinforcement resisting that part of the
13.5.3.2 through 13.5.3.4. moment to be transferred to the column by flexure should be
placed between lines that are one and one-half the slab or
13.5.3.1 — The fraction of unbalanced moment not drop panel thickness, 1.5h, on each side of the column. The
transferred by flexure shall be transferred by eccen- calculated shear stresses in the slab around the column are
tricity of shear in accordance with 11.11.7. required to conform to the requirements of 11.11.2. See
R11.11.1.2 and R11.11.2.1 for more details on application
13.5.3.2 — A fraction of the unbalanced moment of this section.
given by γf Mu shall be considered to be transferred by
flexure within an effective slab width between lines that
are one and one-half slab or drop panel thickness
(1.5h) outside opposite faces of the column or capital,
where Mu is the factored moment to be transferred and
1
γ f = ----------------------------------------------- (13-1)
1 + ( 2 ⁄ 3 ) b1 ⁄ b2
13
13.5.3.3 — For nonprestressed slabs with unbalanced R13.5.3.3 — The 1989 Code procedures remain unchanged,
moments transferred between the slab and columns, it except that under certain conditions it is permitted to adjust the
shall be permitted to increase the value of γf given by level of moment transferred by shear without revising member
Eq. (13-1) in accordance with the following: sizes. Tests indicate that some flexibility in distribution of
unbalanced moments transferred by shear and flexure at both
(a) For edge columns with unbalanced moments exterior and interior supports is possible. Interior, exterior, and
about an axis parallel to the edge, γf = 1.0 provided corner supports refer to slab-column connections for which the
that Vu at an edge support does not exceed critical perimeter for rectangular columns has four, three, or
0.75φVc , or at a corner support does not exceed two sides, respectively. Changes in the 1995 Code recognized,
0.5φVc. to some extent, design practices before the 1971 Code.13.13
(b) For unbalanced moments at interior supports, At exterior supports, for unbalanced moments about an axis
and for edge columns with unbalanced moments parallel to the edge, the portion of moment transferred by
about an axis perpendicular to the edge, increase γf eccentricity of shear γv Mu may be reduced provided that the
to as much as 1.25 times the value from Eq. (13-1), factored shear at the support (excluding the shear produced
but not more than γf = 1.0, provided that Vu at the by moment transfer) does not exceed 75 percent of the shear
support does not exceed 0.4φVc. The net tensile strength φVc as defined in 11.12.2.1 for edge columns or
strain εt calculated for the effective slab width 50 percent for corner columns. Tests13.14,13.15 indicate that
defined in 13.5.3.2 shall not be less than 0.010. there is no significant interaction between shear and
The value of Vc in items (a) and (b) shall be calculated unbalanced moment at the exterior support in such cases.
in accordance with 11.11.2.1. Note that as γv Mu is decreased, γf Mu is increased.
CODE COMMENTARY
When the factored shear for a slab-column connection is
large, the slab-column joint cannot always develop all of the
reinforcement provided in the effective width. The modifi-
cations for interior slab-column connections in 13.5.3.3 are
permitted only when the reinforcement (within the effective
width) required to develop the unbalanced moment γf Mu
has a net tensile strain εt not less than 0.010. The use of
Eq. (13-1) without the modification permitted in 13.5.3.3
will generally indicate overstress conditions on the joint.
The provisions of 13.5.3.3 are intended to improve ductile
behavior of the slab-column joint. When a reversal of
moments occurs at opposite faces of an interior support,
both top and bottom reinforcement should be concen-
trated within the effective width. A ratio of top to bottom
reinforcement of approximately 2 has been observed to
be appropriate.
CODE COMMENTARY
13.6.1 — Limitations R13.6.1 — Limitations
Design of slab systems within the limitations of The direct design method was developed from considerations
13.6.1.1 through 13.6.1.8 by the direct design method of theoretical procedures for the determination of moments
shall be permitted. in slabs with and without beams, requirements for simple
design and construction procedures, and precedents
supplied by performance of slab systems. Consequently, the
slab systems to be designed using the direct design method
should conform to the limitations in this section.
13.6.1.1 — There shall be a minimum of three R13.6.1.1 — The primary reason for the limitation in this
continuous spans in each direction. section is the magnitude of the negative moments at the
interior support in a structure with only two continuous
spans. The rules given for the direct design method assume
that the slab system at the first interior negative moment
section is neither fixed against rotation nor discontinuous.
13.6.1.2 — Panels shall be rectangular, with a ratio R13.6.1.2 — If the ratio of the two spans (long span/short
of longer to shorter span center-to-center of supports span) of a panel exceeds 2, the slab resists the moment in
within a panel not greater than 2. the shorter span essentially as a one-way slab.
13.6.1.3 — Successive span lengths center-to- R13.6.1.3 — The limitation in this section is related to the
center of supports in each direction shall not differ by possibility of developing negative moments beyond the
13 more than one-third the longer span. point where negative moment reinforcement is terminated,
as prescribed in Fig. 13.3.8.
13.6.1.4 — Offset of columns by a maximum of 10 R13.6.1.4 — Columns can be offset within specified
percent of the span (in direction of offset) from either limits from a regular rectangular array. A cumulative total
axis between centerlines of successive columns shall offset of 20 percent of the span is established as the upper
be permitted. limit.
13.6.1.5 — All loads shall be due to gravity only and R13.6.1.5 — The direct design method is based on
uniformly distributed over an entire panel. The tests13.16 for uniform gravity loads and resulting column
unfactored live load shall not exceed two times the reactions determined by statics. Lateral loads such as wind
unfactored dead load. or seismic require a frame analysis. Inverted foundation
mats designed as two-way slabs (see 15.10) involve application
of known column loads. Therefore, even where the soil
reaction is assumed to be uniform, a frame analysis should
be performed.
2
α f 1l2
0.2 ≤ -------------- ≤ 5.0 (13-2)
2
α f 2l1
CODE COMMENTARY
E cb I b
α f = --------------
- (13-3)
E cs I s
13.6.1.8 — Variations from the limitations of 13.6.1 R13.6.1.8 — It is permitted to use the direct design method
shall be permitted if demonstrated by analysis that even if the structure does not fit the limitations in this section,
requirements of 13.5.1 are satisfied. provided it can be shown by analysis that the particular
limitation does not apply to that structure. For a slab system
carrying a nonmovable load (such as a water reservoir in
which the load on all panels is expected to be the same), live
load limitation of 13.6.1.5 need not be satisfied.
13.6.2 — Total factored static moment for a span R13.6.2 — Total factored static moment for a span
13.6.2.5 — Clear span ln shall extend from face to R13.6.2.5 — If a supporting member does not have a
face of columns, capitals, brackets, or walls. Value of rectangular cross section or if the sides of the rectangle are
ln used in Eq. (13-4) shall not be less than 0.65l1. not parallel to the spans, it is to be treated as a square
Circular or regular polygon-shaped supports shall be support having the same area, as illustrated in Fig. R13.6.2.5.
treated as square supports with the same area.
13.6.3 — Negative and positive factored moments R13.6.3 — Negative and positive factored moments
CODE COMMENTARY
13.6.3.3 — In an end span, total factored static R13.6.3.3 — The moment coefficients for an end span are
moment, Mo , shall be distributed as follows: based on the equivalent column stiffness expressions from
References 13.18, 13.19, and 13.20. The coefficients for an
13 (1) (2) (3) (4) (5) unrestrained edge would be used, for example, if the slab
Slab without beams were simply supported on a masonry or concrete wall.
between interior
supports
Those for a fully restrained edge would apply if the slab
Slab with
beams Without Exterior
were constructed integrally with a concrete wall having a
Exterior edge between all edge With edge edge fully flexural stiffness so large compared to that of the slab that
unrestrained supports beam beam restrained
little rotation occurs at the slab-to-wall connection.
Interior
negative
0.75 0.70 0.70 0.70 0.65 For other than unrestrained or fully restrained edges,
factored
moment coefficients in the table were selected to be near the upper
Positive bound of the range for positive moments and interior negative
factored 0.63 0.57 0.52 0.50 0.35
moment moments. As a result, exterior negative moments were usually
Exterior closer to a lower bound. The exterior negative moment
negative strength for most slab systems is governed by minimum
0 0.16 0.26 0.30 0.65
factored
moment reinforcement to control cracking. The final coefficients in
the table have been adjusted so that the absolute sum of the
positive and average moments equal Mo.
CODE COMMENTARY
13.6.3.4 — Negative moment sections shall be R13.6.3.4 — The differences in slab moment on either
designed to resist the larger of the two interior nega- side of a column or other type of support should be
tive factored moments determined for spans framing accounted for in the design of the support. If an analysis is
into a common support unless an analysis is made to made to distribute unbalanced moments, flexural stiffness
distribute the unbalanced moment in accordance with may be obtained on the basis of the gross concrete section
stiffnesses of adjoining elements. of the members involved.
13.6.3.5 — Edge beams or edges of slab shall be R13.6.3.5 — Moments perpendicular to, and at the edge
proportioned to resist in torsion their share of exterior of, the slab structure should be transmitted to the supporting
negative factored moments. columns or walls. Torsional stresses caused by the moment
assigned to the slab should be investigated.
13.6.4 — Factored moments in column strips R13.6.4, R13.6.5, and R13.6.6 — Factored moments in
column strips, beams, and middle strips
13.6.4.1 — Column strips shall be proportioned to
resist the following portions in percent of interior negative The rules given for assigning moments to the column strips,
factored moments: beams, and middle strips are based on studies13.21 of
moments in linearly elastic slabs with different beam stiffness
l2 /l 1 0.5 1.0 2.0 tempered by the moment coefficients that have been used
(αf1l2 /l 1) = 0 75 75 75 successfully. 13
(αf1l 2 /l 1) ≥ 1.0 90 75 45
For the purpose of establishing moments in the half column
Linear interpolations shall be made between values strip adjacent to an edge supported by a wall, ln in Eq. (13-4)
shown. may be assumed equal to ln of the parallel adjacent column
to column span, and the wall may be considered as a beam
having a moment of inertia Ib equal to infinity.
13.6.4.2 — Column strips shall be proportioned to R13.6.4.2 — The effect of the torsional stiffness param-
resist the following portions in percent of exterior eter βt is to assign all of the exterior negative factored
negative factored moments: moment to the column strip, and none to the middle strip,
unless the beam torsional stiffness is high relative to the
l 2/l 1 0.5 1.0 2.0 flexural stiffness of the supported slab. In the definition of
βt = 0 100 100 100 βt , the shear modulus has been taken as Ecb /2.
(αf1l 2/l 1) = 0
βt ≥ 2.5 075 075 075
βt = 0 100 100 100 Where walls are used as supports along column lines, they
(αf1l2/l1) ≥ 1.0
βt ≥ 2.5 090 075 045 can be regarded as very stiff beams with an αf1l2/l1 value
greater than 1. Where the exterior support consists of a wall
Linear interpolations shall be made between values perpendicular to the direction in which moments are being
shown, where βt is calculated in Eq. (13-5) and C is determined, βt may be taken as zero if the wall is of
calculated in Eq. (13-6). masonry without torsional resistance, and βt may be taken
as 2.5 for a concrete wall with great torsional resistance that
E cb C is monolithic with the slab.
β t = -----------------
- (13-5)
2E cs I s
3
∑ ⎛⎝ 1 – 0.63 --y-⎞⎠ ---------
x x y
C = (13-6)
3
CODE COMMENTARY
13.6.4.3 — Where supports consist of columns or
walls extending for a distance equal to or greater than
(0.75)l2 used to compute Mo , negative moments shall
be considered to be uniformly distributed across l2.
13 13.6.5.1 — Beams between supports shall be Loads assigned directly to beams are in addition to the
proportioned to resist 85 percent of column strip uniform dead load of the slab; uniform superimposed dead
moments if αf1l2 /l1 is equal to or greater than 1.0. loads, such as the ceiling, floor finish, or assumed equivalent
partition loads; and uniform live loads. All of these loads are
13.6.5.2 — For values of αf1l2 /l1 between 1.0 and normally included with qu in Eq. (13-4). Linear loads
zero, proportion of column strip moments resisted by applied directly to beams include partition walls over or
beams shall be obtained by linear interpolation along beam centerlines and additional dead load of the
between 85 and zero percent. projecting beam stem. Concentrated loads include posts
above or hangers below the beams. For the purpose of
13.6.5.3 — In addition to moments calculated for assigning directly applied loads, only loads located within
uniform loads according to 13.6.2.2, 13.6.5.1, and the width of the beam stem should be considered as directly
13.6.5.2, beams shall be proportioned to resist all applied to the beams. (The effective width of a beam as
moments caused by concentrated or linear loads defined in 13.2.4 is solely for strength and relative stiffness
applied directly to beams, including weight of projecting calculations.) Line loads and concentrated loads located on
beam stem above or below the slab. the slab away from the beam stem require consideration to
determine their apportionment to slab and beams.
CODE COMMENTARY
13.6.7 — Modification of factored moments R13.6.7 — Modification of factored moments
Modification of negative and positive factored This section permits a reduction of 10 percent in negative or
moments by 10 percent shall be permitted provided positive factored moments, calculated in accordance with
the total static moment for a panel, Mo , in the direction 13.6.3, provided that the total static moment for a panel in
considered is not less than that required by Eq. (13-4). the direction considered is not less than Mo required by
Eq. (13-4). This is intended to recognize a limited amount
of inelastic behavior and moment redistribution can occur in
slabs that were analyzed with the direct design method.
13.6.8 — Factored shear in slab systems with beams R13.6.8 — Factored shear in slab systems with beams
13.6.8.1 — Beams with αf1l2 /l1 equal to or greater The tributary area for computing shear on an interior beam
than 1.0 shall be proportioned to resist shear caused is shown shaded in Fig. R13.6.8. If the stiffness for the
by factored loads on tributary areas which are beam αf1l2 /l1 is less than 1.0, the shear on the beam may be
bounded by 45-degree lines drawn from the corners of obtained by linear interpolation. In such cases, the beams
the panels and the centerlines of the adjacent panels framing into the column will not account for all of the shear
parallel to the long sides. force applied on the column. The remaining shear force will
produce shear stresses in the slab around the column that
13.6.8.2 — In proportioning beams with αf1l2/l1 less should be checked in the same manner as for flat slabs, as
than 1.0 to resist shear, linear interpolation, assuming required by 13.6.8.4. Sections 13.6.8.1 through 13.6.8.3 do
beams carry no load at αf1 = 0, shall be permitted. not apply to the calculation of torsional moments on the
beams. These moments should be based on the calculated
13.6.8.3 — In addition to shears calculated flexural moments acting on the sides of the beam. 13
according to 13.6.8.1 and 13.6.8.2, beams shall be
proportioned to resist shears caused by factored loads
applied directly on beams.
CODE COMMENTARY
13.6.9 — Factored moments in columns and walls R13.6.9 — Factored moments in columns and walls
13.6.9.1 — Columns and walls built integrally with a Equation (13-7) refers to two adjoining spans, with one span
slab system shall resist moments caused by factored longer than the other, and with full dead load plus one-half
loads on the slab system. live load applied on the longer span and only dead load
applied on the shorter span.
13.6.9.2 — At an interior support, supporting elements
above and below the slab shall resist the factored Design and detailing of the reinforcement transferring the
moment specified by Eq. (13-7) in direct proportion to moment from the slab to the edge column is critical to both
their stiffnesses unless a general analysis is made. the performance and the safety of flat slabs or flat plates
without edge beams or cantilever slabs. It is important that
Mu = 0.07[(qDu + 0.5qLu ) l2 l 2n – qDu′ l2′(ln′)2] (13-7) complete design details be shown on design drawings, such
as concentration of reinforcement over the column by closer
where qDu′ , l2′, and ln′ refer to shorter span. spacing or additional reinforcement.
13.7.1 — Design of slab systems by the equivalent The equivalent frame method involves the representation of
frame method shall be based on assumptions given in the three-dimensional slab system by a series of two-
13.7.2 through 13.7.6, and all sections of slabs and dimensional frames that are then analyzed for loads acting
supporting members shall be proportioned for in the plane of the frames. The negative and positive
moments and shears thus obtained. moments so determined at the critical design sections of the
13 frame are distributed to the slab sections in accordance with
13.7.1.1 — Where metal column capitals are used, it 13.6.4 (column strips), 13.6.5 (beams), and 13.6.6 (middle
shall be permitted to take account of their contributions strips). The equivalent frame method is based on studies
to stiffness and resistance to moment and to shear. reported in References 13.18, 13.19, and 13.20. Many of the
details of the equivalent frame method given in the Commen-
13.7.1.2 — It shall be permitted to neglect the tary in the 1989 Code were removed in the 1995 Code.
change in length of columns and slabs due to direct
stress, and deflections due to shear.
13.7.2.1 — The structure shall be considered to be Application of the equivalent frame to a regular structure is
made up of equivalent frames on column lines taken illustrated in Fig. R13.7.2. The three-dimensional building
longitudinally and transversely through the building. is divided into a series of two-dimensional frame bents
(equivalent frames) centered on column or support centerlines
CODE COMMENTARY
13.7.2.2 — Each frame shall consist of a row of with each frame extending the full height of the building.
columns or supports and slab-beam strips, bounded The width of each equivalent frame is bounded by the
laterally by the centerline of panel on each side of the centerlines of the adjacent panels. The complete analysis of
centerline of columns or supports. a slab system for a building consists of analyzing a series of
equivalent (interior and exterior) frames spanning longitudi-
13.7.2.3 — Columns or supports shall be assumed nally and transversely through the building.
to be attached to slab-beam strips by torsional
members (see 13.7.5) transverse to the direction of The equivalent frame comprises three parts: (1) the hori-
the span for which moments are being determined and zontal slab strip, including any beams spanning in the direction
extending to bounding lateral panel centerlines on of the frame, (2) the columns or other vertical supporting
each side of a column. members, extending above and below the slab, and (3) the
elements of the structure that provide moment transfer
13.7.2.4 — Frames adjacent and parallel to an edge between the horizontal and vertical members.
shall be bounded by that edge and the centerline of
adjacent panel.
13.7.3.3 — Moment of inertia of slab-beams from R13.7.3.3 — A support is defined as a column, capital,
center of column to face of column, bracket, or capital bracket, or wall. A beam is not considered to be a support
shall be assumed equal to the moment of inertia of the member for the equivalent frame.
slab-beam at face of column, bracket, or capital
divided by the quantity (1 – c2/l 2)2, where c2 and l 2
are measured transverse to the direction of the span
for which moments are being determined.
13.7.4.1 — Determination of the moment of inertia Column stiffness is based on the length of the column from
of columns at any cross section outside of joints or mid-depth of slab above to mid-depth of slab below.
column capitals using the gross area of concrete shall Column moment of inertia is computed on the basis of its
be permitted. cross section, taking into account the increase in stiffness
provided by the capital, if any.
13.7.4.2 — Variation in moment of inertia along axis
of columns shall be taken into account. When slab-beams are analyzed separately for gravity loads,
the concept of an equivalent column, combining the stiffness
CODE COMMENTARY
13.7.4.3 — Moment of inertia of columns from top to of the slab-beam and torsional member into a composite
bottom of the slab-beam at a joint shall be assumed to element, is used. The column flexibility is modified to
be infinite. account for the torsional flexibility of the slab-to-column
connection that reduces its efficiency for transmission of
moments. The equivalent column consists of the actual
columns above and below the slab-beam, plus attached
torsional members on each side of the columns extending to the
centerline of the adjacent panels as shown in Fig. R13.7.4.
13.7.5.1 — Torsional members (see 13.7.2.3) shall Computation of the stiffness of the torsional member
be assumed to have a constant cross section requires several simplifying assumptions. If no transverse
throughout their length consisting of the largest of (a), beam frames into the column, a portion of the slab equal to
(b), and (c): the width of the column or capital is assumed to be the
torsional member. If a beam frames into the column, T-beam
(a) A portion of slab having a width equal to that of or L-beam action is assumed, with the flanges extending on
the column, bracket, or capital in the direction of the each side of the beam a distance equal to the projection of
span for which moments are being determined; the beam above or below the slab but not greater than four
times the thickness of the slab. Furthermore, it is assumed
(b) For monolithic or fully composite construction, that no torsional rotation occurs in the beam over the width
the portion of slab specified in (a) plus that part of of the support.
the transverse beam above and below the slab;
13 The member sections to be used for calculating the torsional
(c) The transverse beam as defined in 13.2.4.
stiffness are defined in 13.7.5.1. Up to the 1989 Code,
13.7.5.2 — Where beams frame into columns in the Eq. (13-6) specified the stiffness coefficient Kt of the
direction of the span for which moments are being torsional members. In 1995, the approximate expression for
determined, the torsional stiffness shall be multiplied Kt was moved to the Commentary.
by the ratio of the moment of inertia of the slab with
such a beam to the moment of inertia of the slab
without such a beam.
CODE COMMENTARY
9E C
Kt = Σ --------------------------
⎛
cs
c 2⎞ 3
- 13
l 2 1 – -----
⎝ l ⎠ 2
13.7.6.1 — When the loading pattern is known, the The use of only three-quarters of the full factored live load
equivalent frame shall be analyzed for that load. for maximum moment loading patterns is based on the fact
that maximum negative and maximum positive live load
13.7.6.2 — When the unfactored live load is variable moments cannot occur simultaneously and that redistribution
but does not exceed three-quarters of the unfactored of maximum moments is thus possible before failure occurs.
dead load, or the nature of live load is such that all This procedure, in effect, permits some local overstress
panels will be loaded simultaneously, it shall be under the full factored live load if it is distributed in the
permitted to assume that maximum factored moments prescribed manner, but still ensures that the design strength
occur at all sections with full factored live load on of the slab system after redistribution of moment is not less
entire slab system. than that required to carry the full factored dead and live
loads on all panels.
13.7.6.3 — For loading conditions other than those
defined in 13.7.6.2, it shall be permitted to assume
that maximum positive factored moment near midspan
of a panel occurs with three-quarters of the full factored
live load on the panel and on alternate panels; and it
shall be permitted to assume that maximum negative
factored moment in the slab at a support occurs with
three-quarters of the full factored live load on adjacent
panels only.
CODE COMMENTARY
13.7.7 — Factored moments R13.7.7 — Factored moments
13.7.7.1 — At interior supports, the critical section R13.7.7.1-R13.7.7.3 — These Code sections adjust the
for negative factored moment (in both column and negative factored moments to the face of the supports. The
middle strips) shall be taken at face of rectilinear adjustment is modified at an exterior support to limit reductions
supports, but not farther away than 0.175l1 from the in the exterior negative moment. Figure R13.6.2.5 illustrates
center of a column. several equivalent rectangular supports for use in establishing
faces of supports for design with nonrectangular supports.
13.7.7.2 — At exterior supports with brackets or
capitals, the critical section for negative factored
moment in the span perpendicular to an edge shall be
taken at a distance from face of supporting element
not greater than one-half the projection of bracket or
capital beyond face of supporting element.
13.7.7.4 — Where slab systems within limitations of R13.7.7.4 — Previous Codes have contained this section.
13.6.1 are analyzed by the equivalent frame method, it It is based on the principle that if two different methods are
shall be permitted to reduce the resulting computed prescribed to obtain a particular answer, the Code should
13 moments in such proportion that the absolute sum of the not require a value greater than the least acceptable value.
positive and average negative moments used in design Due to the long satisfactory experience with designs having
need not exceed the value obtained from Eq. (13-4). total factored static moments not exceeding those given by
Eq. (13-4), it is considered that these values are satisfactory
for design when applicable limitations are met.
CHAPTER 14 — WALLS
CODE COMMENTARY
14.1 — Scope R14.1 — Scope
14.1.1 — Provisions of Chapter 14 shall apply for Chapter 14 applies generally to walls as vertical load-
design of walls subjected to axial load, with or without carrying members. Cantilever retaining walls are designed
flexure. according to the flexural design provisions of Chapter 10.
Walls designed to resist shear forces, such as shear walls,
14.1.2 — Cantilever retaining walls are designed should be designed in accordance with Chapter 14 and 11.9
according to flexural design provisions of Chapter 10 as applicable.
with minimum horizontal reinforcement according to
14.3.3. In the 1977 Code, walls could be designed according to
Chapter 14 or 10.15. In the 1983 Code, these two were
combined in Chapter 14.
14.2.1 — Walls shall be designed for eccentric loads Walls should be designed to resist all loads to which they
and any lateral or other loads to which they are are subjected, including eccentric axial loads and lateral
subjected. forces. Design is to be carried out in accordance with 14.4
unless the wall meets the requirements of 14.5.1.
14.2.2 — Walls subject to axial loads shall be
designed in accordance with 14.2, 14.3, and either
14.4, 14.5, or 14.8. 14
14.2.3 — Design for shear shall be in accordance with
11.9.
CODE COMMENTARY
14.3 — Minimum reinforcement R14.3 — Minimum reinforcement
14.3.1 — Minimum vertical and horizontal reinforce- The requirements of 14.3 are similar to those in previous
ment shall be in accordance with 14.3.2 and 14.3.3 codes. These apply to walls designed according to 14.4,
unless a greater amount is required for shear by 14.5, or 14.8. For walls resisting horizontal shear forces in
11.9.8 and 11.9.9. the plane of the wall, reinforcement designed according to
11.9.9.2 and 11.9.9.4 may exceed the minimum reinforcement
14.3.2 — Minimum ratio of vertical reinforcement area in 14.3.
to gross concrete area, ρl, shall be:
The notation used to identify the direction of the distributed
(a) 0.0012 for deformed bars not larger than No. 16 reinforcement in walls was updated in 2005 to eliminate
with fy not less than 420 MPa; or conflicts between the notation used for ordinary structural
walls in Chapters 11 and 14 and the notation used for
(b) 0.0015 for other deformed bars; or special structural walls in Chapter 21. The distributed rein-
(c) 0.0012 for welded wire reinforcement not larger forcement is now identified as being oriented parallel to
than MW200 or MD200. either the longitudinal or transverse axis of the wall. There-
fore, for vertical wall segments, the notation used to
14.3.3 — Minimum ratio of horizontal reinforcement describe the horizontal distributed reinforcement ratio is ρt,
area to gross concrete area, ρt , shall be: and the notation used to describe the vertical distributed
reinforcement ratio is ρl.
(a) 0.0020 for deformed bars not larger than No. 16
with fy not less than 420 MPa; or
CODE COMMENTARY
and one No. 16 bar in walls having a single layer of
reinforcement in both directions shall be provided
around window, door, and similar sized openings.
Such bars shall be anchored to develop fy in tension at
the corners of the openings.
14.5.1 — Walls of solid rectangular cross section shall The empirical design method applies only to solid rectangular
be permitted to be designed by the empirical provisions cross sections. All other shapes should be designed
of 14.5 if the resultant of all factored loads is located according to 14.4.
within the middle third of the overall thickness of the
wall and all limits of 14.2, 14.3, and 14.5 are satisfied. Eccentric loads and lateral forces are used to determine the
total eccentricity of the factored axial force Pu. When the
14.5.2 — Design axial strength φPn of a wall satisfying resultant load for all applicable load combinations falls
limitations of 14.5.1 shall be computed by Eq. (14-1) within the middle third of the wall thickness (eccentricity
unless designed in accordance with 14.4. not greater than h/6) at all sections along the length of the 14
undeformed wall, the empirical design method may be
kl c ⎞ 2 used. The design is then carried out considering Pu as the
φ P n = 0.55φf c′ A g 1 – ⎛ ---------
- (14-1) concentric load. The factored axial force Pu should be less
⎝ 32h⎠
than or equal to the design axial strength φPn computed by
Eq. (14-1), Pu ≤ φPn.
where φ shall correspond to compression-controlled
sections in accordance with 9.3.2.2 and effective
With the 1980 Code supplement, Eq. (14-1) was revised to
length factor k shall be:
reflect the general range of end conditions encountered in
wall designs. The wall strength equation in the 1977 Code
For walls braced top and bottom against lateral
was based on the assumption of a wall with top and bottom
translation and
fixed against lateral movement, and with moment restraint
at one end corresponding to an effective length factor
(a) Restrained against rotation at one or both ends
between 0.8 and 0.9. Axial strength values determined from
(top, bottom, or both)............................................0.8
the original equation were unconservative when compared
(b) Unrestrained against rotation at both ends.....1.0 to test results14.1 for walls with pinned conditions at both
ends, as occurs with some precast and tilt-up applications,
For walls not braced against lateral translation ....... 2.0 or when the top of the wall is not effectively braced against
translation, as occurs with free-standing walls or in large
structures where significant roof diaphragm deflections
occur due to wind and seismic loads. Equation (14-1) gives
the same results as the 1977 Code for walls braced against
translation and with reasonable base restraint against
rotation.14.2 Values of effective length factors k are given for
commonly occurring wall end conditions. The end condition
“restrained against rotation” required for a k of 0.8 implies
attachment to a member having flexural stiffness EI/l at
least as large as that of the wall.
CODE COMMENTARY
14
14.5.3 — Minimum thickness of walls designed by R14.5.3 — Minimum thickness of walls designed by
empirical design method empirical design method
14.5.3.1 — Thickness of bearing walls shall not be The minimum thickness requirements need not be applied
less than 1/25 the supported height or length, which- to walls designed according to 14.4.
ever is shorter, nor less than 100 mm.
CODE COMMENTARY
14.8 — Alternative design of slender walls R14.8 — Alternative design of slender walls
14.8.1 — When flexural tension controls the out-of- Section 14.8 was introduced in the 1999 edition and the
plane design of a wall, the requirements of 14.8 are provisions are based on requirements in the 1997 Uniform
considered to satisfy 10.10. Building Code (UBC)14.3 and experimental research.14.4
Changes were included in the 2008 edition to reduce
14.8.2 — Walls designed by the provisions of 14.8 differences in the serviceability provisions and ensure that
shall satisfy 14.8.2.1 through 14.8.2.6. the intent of the UBC provisions is included in future
editions of the International Building Code.
14.8.2.1 — The wall panel shall be designed as a
simply supported, axially loaded member subjected to The procedure is presented as an alternative to the require-
an out-of-plane uniform lateral load, with maximum ments of 10.10 for the out-of-plane design of slender wall
moments and deflections occurring at midspan. panels, where the panels are restrained against overturning
at the top.
14.8.2.2 — The cross section shall be constant over
the height of the panel. Panels that have windows or other large openings are not
considered to have constant cross section over the height of
the panel. Such walls are to be designed taking into account
the effects of openings.
14.8.2.3 — The wall shall be tension-controlled. R14.8.2.3 — This section was updated in the 2005 Code
to reflect the change in design approach that was introduced
in 10.3 of the 2002 Code. The previous requirement that the 14
reinforcement ratio should not exceed 0.6ρbal was replaced
by the requirement that the wall be tension-controlled,
leading to approximately the same reinforcement ratio.
CODE COMMENTARY
14.8.3 — Design moment strength φMn for combined R14.8.3 — Before the 2008 edition, the effective area of
flexure and axial loads at midheight shall be longitudinal reinforcement in a slender wall for obtaining an
approximate cracked moment of inertia was calculated
φMn ≥ Mu (14-3) using an effective area of tension reinforcement defined as
where P
A se, w = A s + -----u-
fy
Mu = Mua + PuΔu (14-4)
Mua is the maximum factored moment at midheight of However, this term overestimated the contribution of axial
wall due to lateral and eccentric vertical loads, not load in many cases where two layers of reinforcement were
including PΔ effects, and Δu is used in the slender wall. Therefore, the effective area of
longitudinal reinforcement was modified in 2008
2
5M u l c P h/2
Δ u = -------------------------------------
( 0.75 )48E c I cr
(14-5) A se, w = A s + -----u- ⎛ --------⎞
fy ⎝ d ⎠
Mu shall be obtained by iteration of deflections, or by The neutral axis depth, c, in Eq. (14-7) corresponds to this
Eq. (14-6). effective area of longitudinal reinforcement.
M ua
M u = ----------------------------------------------
- (14-6)
2
5P u l c
1 – -------------------------------------
( 0.75 )48E c I cr
14
where
3
E P h 2 lw c
I cr = ------s ⎛ A s + ------u- -------⎞ ( d – c ) + -----------
- (14-7)
E ⎝ c f 2d⎠ y 3
14.8.4 — Maximum out-of-plane deflection, Δs , due to R14.8.4 — Before the 2008 edition, out-of-plane deflections
service loads, including PΔ effects, shall not exceed in wall panels were calculated using the procedures in
lc /150. Section 9.5.2.3. However, re-evaluation of the original test
data14.4 demonstrated that out-of-plane deflections increase
rapidly when the service-level moment exceeds 2/3Mcr. A
If Ma , maximum moment at midheight of wall due to
linear interpolation between Δcr and Δn is used to determine
service lateral and eccentric vertical loads, including
Δs to simplify the design of slender walls if Ma > 2/3Mcr.
PΔ effects, exceeds (2/3)Mcr , Δs shall be calculated by
Eq. (14-8)
Service-level load combinations are not defined in Chapter 9 of
ACI 318, but they are discussed in Appendix C of ASCE/
( M a – ( 2/3 )M cr ) SEI 7-05.14.7 Unlike ACI 318, however, appendixes to
- ( Δ – ( 2/3 )Δ cr ) (14-8)
Δ s = ( 2/3 )Δ cr + -----------------------------------------
( M n – ( 2/3 )M cr ) n ASCE/SEI 7 are not considered to be mandatory parts of the
standard. For calculating service-level lateral deflections of
If Ma does not exceed (2/3)Mcr , Δs shall be calculated structures, Appendix C of ASCE/SEI 7-05 recommends
by Eq. (14-9) using the following load combination
Ma ⎞ D + 0.5L + 0.7W
Δ s = ⎛ --------- Δ (14-9)
⎝ M -⎠ cr
cr which corresponds to a 5 percent annual probability of
exceedance. If the slender wall is designed to resist earth-
CODE COMMENTARY
where quake effects, E, and E is based on strength-level seismic
forces, the following load combination is considered to be
2 appropriate for evaluating the service-level lateral deflections
5M cr l c
Δ cr = ------------------
- (14-10)
48E c I g D + 0.5L + 0.7E
2
5M n l c
Δ n = --------------------
- (14-11)
48E c I cr
14
14
CHAPTER 15 — FOOTINGS
CODE COMMENTARY
15.1 — Scope R15.1 — Scope
15.1.1 — Provisions of Chapter 15 shall apply for While the provisions of Chapter 15 apply to isolated footings
design of isolated footings and, where applicable, to supporting a single column or wall, most of the provisions
combined footings and mats. are generally applicable to combined footings and mats
supporting several columns or walls or a combination
15.1.2 — Additional requirements for design of thereof.15.1,15.2
combined footings and mats are given in 15.10.
15.2.1 — Footings shall be proportioned to resist the Footings are required to be proportioned to sustain the
factored loads and induced reactions, in accordance applied factored loads and induced reactions, which include
with the appropriate design requirements of this Code axial loads, moments, and shears that have to be resisted at
and as provided in Chapter 15. the base of the footing or pile cap.
15.2.2 — Base area of footing or number and arrange- After the permissible soil pressure or the permissible pile
ment of piles shall be determined from unfactored capacity has been determined by principles of soil
forces and moments transmitted by footing to soil or mechanics and in accord with the general building code, the
piles and permissible soil pressure or permissible pile size of the base area of a footing on soil or the number and
capacity determined through principles of soil arrangement of the piles should be established on the basis
mechanics. of unfactored (service) loads such as D, L, W, and E in
whatever combination that governs the design.
15
15.2.3 — For footings on piles, computations for
moments and shears shall be permitted to be based Only the computed end moments that exist at the base of a
on the assumption that the reaction from any pile is column (or pedestal) need to be transferred to the footing;
concentrated at pile center. the minimum moment requirement for slenderness consid-
erations given in 10.6.5 need not be considered for transfer
of forces and moments to footings.
CODE COMMENTARY
In the case of eccentric loading, load factors may cause
eccentricities and reactions that are different from those
obtained by unfactored loads.
15.4.4 — In two-way rectangular footings, reinforce- R15.4.4 — In previous Codes, the reinforcement in the short
ment shall be distributed in accordance with 15.4.4.1 direction of rectangular footings should be distributed so that
and 15.4.4.2. an area of steel given by Eq. (15-1) is provided in a band
width equal to the length of the short side of the footing. The
15.4.4.1 — Reinforcement in long direction shall be band width is centered about the column centerline.
distributed uniformly across entire width of footing.
The remaining reinforcement required in the short direction
15.4.4.2 — For reinforcement in short direction, a is to be distributed equally over the two segments outside
portion of the total reinforcement, γsAs , shall be the band width, one-half to each segment.
distributed uniformly over a band width (centered on
centerline of column or pedestal) equal to the length of
short side of footing. Remainder of reinforcement
required in short direction, (1 – γs)As , shall be distributed
uniformly outside center band width of footing.
CODE COMMENTARY
2
γ s = ------------------ (15-1)
(β + 1)
15.5.1 — Shear strength of footings supported on soil R15.5.1 and R15.5.2 — The shear strength of footings are
or rock shall be in accordance with 11.11. determined for the more severe condition of 11.11.1.1 or
11.11.1.2. The critical section for shear is measured from
15.5.2 — Location of critical section for shear in accor- the face of supported member (column, pedestal, or wall),
dance with Chapter 11 shall be measured from face of except for supported members on steel base plates.
column, pedestal, or wall, for footings supporting a
column, pedestal, or wall. For footings supporting a Computation of shear requires that the soil reaction qs be
column or pedestal with steel base plates, the critical obtained from the factored loads and the design be in
section shall be measured from location defined in accordance with the appropriate equations of Chapter 11.
15.4.2(c).
Where necessary, shear around individual piles may be
investigated in accordance with 11.11.1.2. If shear perime-
ters overlap, the modified critical perimeter bo should be
taken as that portion of the smallest envelope of individual
shear perimeter that will actually resist the critical shear for
the group under consideration. One such situation is illus-
trated in Fig. R15.5.
15.5.3 — Where the distance between the axis of any R15.5.3 — Pile caps supported on piles in more than one
pile to the axis of the column is more than two times plane can be designed using three-dimensional strut-and-tie 15
the distance between the top of the pile cap and the models satisfying Appendix A.15.3 The effective concrete
top of the pile, the pile cap shall satisfy 11.11 and compressive strength is from A.3.2.2(b) because it is generally
15.5.4. Other pile caps shall satisfy either Appendix A, not feasible to provide confining reinforcement satisfying
or both 11.11 and 15.5.4. If Appendix A is used, the A.3.3.1 and A.3.3.2 in a pile cap.
effective concrete compression strength of the struts,
fce , shall be determined using A.3.2.2(b).
15.5.4 —Computation of shear on any section through R15.5.4 — When piles are located inside the critical sections
a footing supported on piles shall be in accordance d or d/2 from face of column, for one-way or two-way shear,
with 15.5.4.1, 15.5.4.2, and 15.5.4.3. respectively, an upper limit on the shear strength at a section
adjacent to the face of the column should be considered.
15.5.4.1 — Entire reaction from any pile with its The CRSI Handbook15.4 offers guidance for this situation.
center located dpile /2 or more outside the section shall
be considered as producing shear on that section.
CODE COMMENTARY
15.6 — Development of reinforcement in
footings
15.8 — Transfer of force at base of column, R15.8 — Transfer of force at base of column,
wall, or reinforced pedestal wall, or reinforced pedestal
15
15.8.1 — Forces and moments at base of column, Section 15.8 provides the specific requirements for force
wall, or pedestal shall be transferred to supporting transfer from a column, wall, or pedestal (supported
pedestal or footing by bearing on concrete and by member) to a pedestal or footing (supporting member).
reinforcement, dowels, and mechanical connectors. Force transfer should be by bearing on concrete (compressive
force only) and by reinforcement (tensile or compressive
force). Reinforcement may consist of extended longitudinal
bars, dowels, anchor bolts, or suitable mechanical connectors.
15.8.1.1 — Bearing stress on concrete at contact R15.8.1.1 — Compressive force may be transmitted to a
surface between supported and supporting member supporting pedestal or footing by bearing on concrete. For
shall not exceed concrete bearing strength for either strength design, allowable bearing stress on the loaded area
surface as given by 10.14. is equal to 0.85φfc′ , if the loaded area is equal to the area on
which it is supported.
CODE COMMENTARY
extended into the footing. The unit bearing stress on the
column will normally be 0.85φ fc′ . The permissible bearing
strength on the footing may be increased in accordance with
10.14 and will usually be two times 0.85φfc′ . The compressive
force that exceeds that developed by the permissible bearing
strength at the base of the column or at the top of the footing
should be carried by dowels or extended longitudinal bars.
15.8.1.2 — Reinforcement, dowels, or mechanical R15.8.1.2 — All tensile forces, whether created by uplift,
connectors between supported and supporting moment, or other means, should be transferred to supporting
members shall be adequate to transfer: pedestal or footing entirely by reinforcement or suitable
mechanical connectors. Generally, mechanical connectors
(a) All compressive force that exceeds concrete would be used only in precast construction.
bearing strength of either member;
15.8.1.3 — If calculated moments are transferred to R15.8.1.3 — If computed moments are transferred from
supporting pedestal or footing, then reinforcement, the column to the footing, the concrete in the compression
dowels, or mechanical connectors shall be adequate zone of the column will be stressed to 0.85φfc′ under
to satisfy 12.17. factored load conditions and, as a result, all the reinforce-
ment will generally have to be doweled into the footing.
15.8.1.4 — Lateral forces shall be transferred to R15.8.1.4 — The shear-friction method given in 11.6 may
supporting pedestal or footing in accordance with be used to check for transfer of lateral forces to supporting
15
shear-friction provisions of 11.6, or by other appro- pedestal or footing. Shear keys may be used, provided that the
priate means. reinforcement crossing the joint satisfies 15.8.2.1, 15.8.3.1,
and the shear-friction requirements of 11.6. In precast
construction, resistance to lateral forces may be provided by
shear-friction, shear keys, or mechanical devices.
15.8.2.1 — For cast-in-place columns and pedestals, R15.8.2.1 and R15.8.2.2 — A minimum amount of
area of reinforcement across interface shall be not less reinforcement is required between all supported and
than 0.005Ag , where Ag is the gross area of the supporting members to ensure ductile behavior. The Code
supported member. does not require that all bars in a column be extended
through and be anchored into a footing. However, reinforce-
15.8.2.2 — For cast-in-place walls, area of reinforce- ment with an area of 0.005 times the column area or an
ment across interface shall be not less than minimum equal area of properly spliced dowels is required to extend
vertical reinforcement given in 14.3.2. into the footing with proper anchorage. This reinforcement
is required to provide a degree of structural integrity during
the construction stage and during the life of the structure.
15.8.2.3 — At footings, it shall be permitted to lap R15.8.2.3 — Lap splices of No. 43 and No. 57 longitu-
splice No. 43 and No. 57 longitudinal bars, in dinal bars in compression only to dowels from a footing are
compression only, with dowels to provide reinforce- specifically permitted in 15.8.2.3. The dowel bars should be
ment required to satisfy 15.8.1. Dowels shall not be No. 36 or smaller in size. The dowel lap splice length should
larger than No. 36 bar and shall extend into supported meet the larger of the two criteria: (a) be able to transfer the
CODE COMMENTARY
member a distance not less than the larger of ldc , of stress in the No. 43 and No. 57 bars, and (b) fully develop
No. 43 or No. 57 bars and compression lap splice the stress in the dowels as a splice.
length of the dowels, whichever is greater, and into the
footing a distance not less than ldc of the dowels. This provision is an exception to 12.14.2.1, which prohibits
lap splicing of No. 43 and No. 57 bars. This exception
results from many years of successful experience with the
lap splicing of these large column bars with footing dowels
of the smaller size. The reason for the restriction on dowel
bar size is recognition of the anchorage length problem of
the large bars, and to allow use of the smaller size dowels. A
similar exception is allowed for compression splices
between different size bars in 12.16.2.
15.8.3.1 — Connection between precast columns or R15.8.3.1 and R15.8.3.2 — For cast-in-place columns,
pedestals and supporting members shall meet the 15.8.2.1 requires a minimum area of reinforcement equal to
requirements of 16.5.1.3(a). 0.005Ag across the column-footing interface to provide
some degree of structural integrity. For precast columns,
15.8.3.2 — Connection between precast walls and this requirement is expressed in terms of an equivalent
15 supporting members shall meet the requirements of tensile force that should be transferred. Thus, across the
16.5.1.3(b) and (c). joint, As fy = 1.4Ag [see 16.5.1.3(a)]. The minimum tensile
strength required for precast wall-to-footing connection [see
16.5.1.3(b)] is somewhat less than that required for
columns, since an overload would be distributed laterally
and a sudden failure would be less likely. Since the tensile
strength values of 16.5.1.3 have been arbitrarily chosen, it is
not necessary to include a strength reduction factor φ for
these calculations.
CODE COMMENTARY
15.10 — Combined footings and mats R15.10 — Combined footings and mats
15.10.1 — Footings supporting more than one column, R15.10.1 — Any reasonable assumption with respect to the
pedestal, or wall (combined footings or mats) shall be distribution of soil pressure or pile reactions can be used as
proportioned to resist the factored loads and induced long as it is consistent with the type of structure and the
reactions, in accordance with appropriate design properties of the soil, and conforms with established principles
requirements of the code. of soil mechanics (see 15.1). Similarly, as prescribed in
15.2.2 for isolated footings, the base area or pile arrangement
of combined footings and mats should be determined using
the unfactored forces, moments, or both, transmitted by the
footing to the soil, considering permissible soil pressures
and pile reactions.
15.10.4 — Minimum reinforcing steel in nonprestressed R15.10.4 — Minimum reinforcing steel may be distributed
mat foundations shall meet the requirements of 7.12.2 near the top or bottom of the section, or may be allocated
in each principal direction. Maximum spacing shall not between the two faces of the section as deemed appropriate
exceed 450 mm. for specific conditions, such that the total area of continuous
reinforcing steel satisfies 7.12.2.
15
CODE COMMENTARY
16.1 — Scope R16.1 — Scope
16.1.1 — All provisions of this Code, not specifically R16.1.1 — See 2.2 for definition of precast concrete.
excluded and not in conflict with the provisions of
Chapter 16, shall apply to structures incorporating Design and construction requirements for precast concrete
precast concrete structural members. structural members differ in some respects from those for
cast-in-place concrete structural members and these differ-
ences are addressed in this chapter. Where provisions for
cast-in-place concrete applied to precast concrete, they have
not been repeated. Similarly, items related to composite
concrete in Chapter 17 and to prestressed concrete in
Chapter 18 that apply to precast concrete are not restated.
16.2.1 — Design of precast members and connections R16.2.1 — Stresses developed in precast members during
shall include loading and restraint conditions from the period from casting to final connection may be greater
initial fabrication to end use in the structure, including than the service load stresses. Handling procedures may
form removal, storage, transportation, and erection. cause undesirable deformations. Care should be given to the
methods of storing, transporting, and erecting precast
16
members so that performance at service loads and strength
under factored loads meet Code requirements.
16.2.2 — When precast members are incorporated R16.2.2 — The structural behavior of precast members may
into a structural system, the forces and deformations differ substantially from that of similar members that are
occurring in and adjacent to connections shall be cast-in-place. Design of connections to minimize or
included in the design. transmit forces due to shrinkage, creep, temperature change,
elastic deformation, differential settlement, wind, and earth-
quake require consideration in precast construction.
16.2.3 — Tolerances for both precast members and R16.2.3 — Design of precast members and connections is
interfacing members shall be specified. Design of particularly sensitive to tolerances on the dimensions of
precast members and connections shall include the individual members and on their location in the structure. To
effects of these tolerances. prevent misunderstanding, the tolerances used in design
should be specified in the contract documents. Instead of
specifying individual tolerances, the tolerance standard
assumed in design may be specified. It is important to specify
any deviations from accepted standards.
CODE COMMENTARY
16.2.4 — In addition to the requirements for drawings R16.2.4 — The additional requirements may be included in
and specifications in 1.2, (a) and (b) shall be included either contract documents or shop drawings, depending on
in either the contract documents or shop drawings: the assignment of responsibility for design.
16.3.1 — Distribution of forces that are perpendicular R16.3.1 — Concentrated point and line loads can be distributed
to the plane of members shall be established by among members provided they have sufficient torsional
analysis or by test. stiffness and that shear can be transferred across joints.
Torsionally stiff members such as hollow-core or solid slabs
have more favorable load distribution properties than do
torsionally flexible members such as double tees with thin
flanges. The actual distribution of the load depends on many
factors discussed in detail in References 16.13 through
16.19. Large openings can cause significant changes in
distribution of forces.
16.3.2 — Where the system behavior requires in- R16.3.2 — In-plane forces result primarily from diaphragm
plane forces to be transferred between the members action in floors and roofs, causing tension or compression in
of a precast floor or wall system, 16.3.2.1 and 16.3.2.2 the chords and shear in the body of the diaphragm. A
shall apply. continuous path of steel, steel reinforcement, or both, using
16 lap splices, mechanical or welded splices, or mechanical
16.3.2.1 — In-plane force paths shall be continuous connectors, should be provided to carry the tension, whereas
through both connections and members. the shear and compression may be carried by the net
concrete section. A continuous path of steel through a
16.3.2.2 — Where tension forces occur, a contin- connection includes bolts, weld plates, headed studs, or
uous path of steel or steel reinforcement shall be other steel devices. Tension forces in the connections are to
provided. be transferred to the primary reinforcement in the members.
16.4.1 — In one-way precast floor and roof slabs and R16.4.1 — For prestressed concrete members not wider
in one-way precast, prestressed wall panels, all not than 3.7 m, such as hollow-core slabs, solid slabs, or slabs
wider than 3.7 m, and where members are not mechani- with closely spaced ribs, there is usually no need to provide
cally connected to cause restraint in the transverse transverse reinforcement to withstand shrinkage and
direction, the shrinkage and temperature reinforcement temperature stresses in the short direction. This is generally
CODE COMMENTARY
requirements of 7.12 in the direction normal to the flex- true also for nonprestressed floor and roof slabs. The 3.7 m
ural reinforcement shall be permitted to be waived. width is less than that in which shrinkage and temperature
This waiver shall not apply to members that require stresses can build up to a magnitude requiring transverse
reinforcement to resist transverse flexural stresses. reinforcement. In addition, much of the shrinkage occurs
before the members are tied into the structure. Once in the
final structure, the members are usually not as rigidly
connected transversely as monolithic concrete, thus the
transverse restraint stresses due to both shrinkage and
temperature change are significantly reduced.
16.4.2 — For precast, nonprestressed walls the R16.4.2 — This minimum area of wall reinforcement,
reinforcement shall be designed in accordance with instead of the minimum values in 14.3, has been used for
the provisions of Chapters 10 or 14, except that the many years and is recommended by the PCI 16.4 and the
area of horizontal and vertical reinforcement each Canadian Building Code.16.20 The provisions for reduced
shall be not less than 0.001Ag , where Ag is the gross minimum reinforcement and greater spacing recognize that
cross-sectional area of the wall panel. Spacing of rein- precast wall panels have very little restraint at their edges
forcement shall not exceed 5 times the wall thickness nor during early stages of curing and develop less shrinkage
750 mm for interior walls nor 450 mm for exterior walls. stress than comparable cast-in-place walls.
16.5.1 — Except where the provisions of 16.5.2 R16.5.1 — The provisions of 7.13.3 apply to all precast
govern, the minimum provisions of 16.5.1.1 through concrete structures. Sections 16.5.1 and 16.5.2 give minimum
16.5.1.4 for structural integrity shall apply to all precast requirements to satisfy 7.13.3. It is not intended that these
concrete structures. minimum requirements override other applicable provisions
of the Code for design of precast concrete structures.
16
The overall integrity of a structure can be substantially
enhanced by minor changes in the amount, location, and
detailing of member reinforcement and in the detailing of
connection hardware.
16.5.1.1 — Longitudinal and transverse ties required R16.5.1.1 — Individual members may be connected into
by 7.13.3 shall connect members to a lateral load- a lateral load-resisting system by alternative methods. For
resisting system. example, a load-bearing spandrel could be connected to a
diaphragm (part of the lateral load-resisting system). Struc-
tural integrity could be achieved by connecting the spandrel
into all or a portion of the deck members forming the
diaphragm. Alternatively, the spandrel could be connected
only to its supporting columns, which in turn is connected to
the diaphragm.
16.5.1.2 — Where precast elements form floor or R16.5.1.2 — Diaphragms are typically provided as part
roof diaphragms, the connections between diaphragm of the lateral load-resisting system. The ties prescribed in
and those members being laterally supported shall 16.5.1.2 are the minimum required to attach members to the
have a nominal tensile strength capable of resisting floor or roof diaphragms. The tie force is equivalent to the
not less than 4.4 kN per linear m. service load value of 3 kN/m given in the Uniform
Building Code.
16.5.1.3 — Vertical tension tie requirements of R16.5.1.3 — Base connections and connections at
7.13.3 shall apply to all vertical structural members, horizontal joints in precast columns and wall panels,
except cladding, and shall be achieved by providing including shear walls, are designed to transfer all design
CODE COMMENTARY
connections at horizontal joints in accordance with forces and moments. The minimum tie requirements of
(a) through (c): 16.5.1.3 are not additive to these design requirements.
Common practice is to place the wall ties symmetrically
(a) Precast columns shall have a nominal strength in about the vertical centerline of the wall panel and within the
tension not less than 1.4Ag , in lb. For columns with outer quarters of the panel width, wherever possible.
a larger cross section than required by consideration
of loading, a reduced effective area Ag, based on
cross section required but not less than one-half the
total area, shall be permitted;
16.5.1.4 — Connection details that rely solely on R16.5.1.4 — In the event of damage to a beam, it is
friction caused by gravity loads shall not be used. important that displacement of its supporting members be
minimized, so that other members will not lose their load-
carrying ability. This situation shows why connection
details that rely solely on friction caused by gravity loads
are not used. An exception could be heavy modular unit
structures (one or more cells in cell-type structures) where
resistance to overturning or sliding in any direction has a
large factor of safety. Acceptance of such systems should be
based on the provisions of 1.4.
16 16.5.2 — For precast concrete bearing wall structures R16.5.2 — The structural integrity minimum tie provisions
three or more stories in height, the minimum provi- for bearing wall structures, often called large panel structures,
sions of 16.5.2.1 through 16.5.2.5 shall apply. are intended to provide catenary hanger supports in case of
loss of a bearing wall support, as shown by test.16.21 Forces
induced by loading, temperature change, creep, and wind or
seismic action may require a larger amount of tie force. It is
intended that the general precast concrete provisions of
16.5.1 apply to bearing wall structures less than three stories
in height.
16.5.2.1 — Longitudinal and transverse ties shall be R16.5.2.1 — Longitudinal ties may project from slabs
provided in floor and roof systems to provide a nominal and be lap spliced, welded, or mechanically connected, or
strength of 22 kN per meter of width or length. Ties they may be embedded in grout joints, with sufficient length
shall be provided over interior wall supports and and cover to develop the required force. Bond length for
between members and exterior walls. Ties shall be unstressed prestressing steel should be sufficient to develop
positioned in or within 600 mm of the plane of the floor the yield strength.16.23 It is not uncommon to have ties
or roof system. positioned in the walls reasonably close to the plane of the
floor or roof system.
CODE COMMENTARY
16.5.2.3 — Transverse ties perpendicular to floor or R16.5.2.3 — Transverse ties may be uniformly spaced
roof slab spans shall be spaced not greater than the either encased in the panels or in a topping, or they may be
bearing wall spacing. concentrated at the transverse bearing walls.
16.5.2.4 — Ties around the perimeter of each floor R16.5.2.4 —The perimeter tie requirements need not be
and roof, within 1.2 m of the edge, shall provide a additive with the longitudinal and transverse tie requirements. 16
nominal strength in tension not less than 71 kN.
16.6 — Connection and bearing design R16.6 — Connection and bearing design
16.6.1 — Forces shall be permitted to be transferred R16.6.1 — The Code permits a variety of methods for
between members by grouted joints, shear keys, connecting members. These are intended for transfer of
mechanical connectors, reinforcing steel connections, forces both in-plane and perpendicular to the plane of the
reinforced topping, or a combination of these means. members.
16.6.1.2 — When designing a connection using mate- R16.6.1.2 — Various components in a connection (such
rials with different structural properties, their relative stiff- as bolts, welds, plates, and inserts) have different properties
nesses, strengths, and ductilities shall be considered. that can affect the overall behavior of the connection.
CODE COMMENTARY
16.6.2 — Bearing for precast floor and roof members
on simple supports shall satisfy 16.6.2.1 and 16.6.2.2.
16.6.2.1—The allowable bearing stress at the R16.6.2.1 — When tensile forces occur in the plane of the
contact surface between supported and supporting bearing, it may be desirable to reduce the allowable bearing
members and between any intermediate bearing stress, provide confinement reinforcement, or both. Guide-
elements shall not exceed the bearing strength for lines are provided in Reference 16.4.
either surface or the bearing element, or both.
Concrete bearing strength shall be as given in 10.14.
16.6.2.2 — Unless shown by test or analysis that R16.6.2.2 — This section differentiates between bearing
performance will not be impaired, (a) and (b) shall be length and length of the end of a precast member over the
met: support (Fig. R16.6.2). Bearing pads distribute concentrated
loads and reactions over the bearing area, and allow limited
(a) Each member and its supporting system shall horizontal and rotational movements for stress relief. To
have design dimensions selected so that, after prevent spalling under heavily loaded bearing areas, bearing
consideration of tolerances, the distance from the pads should not extend to the edge of the support unless the
edge of the support to the end of the precast edge is armored. Edges can be armored with anchored steel
member in the direction of the span is at least ln /180, plates or angles. Section 11.9.7 gives requirements for
but not less than: bearing on brackets or corbels.
For solid or hollow-core slabs .........................50 mm
For beams or stemmed members ..................75 mm
16.6.2.3 — The requirements of 12.11.1 shall not R16.6.2.3 — It is unnecessary to develop positive bending
16 apply to the positive bending moment reinforcement moment reinforcement beyond the ends of the precast
for statically determinate precast members, but at element if the system is statically determinate. Tolerances
least one-third of such reinforcement shall extend to need to be considered to avoid bearing on structural plain
the center of the bearing length, taking into account concrete where reinforcement has been discontinued.
permitted tolerances in 7.5.2.2 and 16.2.3.
CODE COMMENTARY
16.7 — Items embedded after concrete R16.7 — Items embedded after concrete
placement placement
16.7.1 — When approved by the licensed design R16.7.1 — Section 16.7.1 is an exception to the provisions of
professional, embedded items (such as dowels or 7.5.1. Many precast products are manufactured in such a way
inserts) that either protrude from the concrete or that it is difficult, if not impossible, to position reinforcement
remain exposed for inspection shall be permitted to be that protrudes from the concrete before the concrete is placed.
embedded while the concrete is in a plastic state Such items as ties for horizontal shear and inserts can be
provided that 16.7.1.1, 16.7.1.2, and 16.7.1.3 are met. placed while the concrete is plastic, if proper precautions are
taken. This exception is not applicable to reinforcement that
16.7.1.1 — Embedded items are not required to be is completely embedded, or to embedded items that will be
hooked or tied to reinforcement within the concrete. hooked or tied to embedded reinforcement.
16.9.2 — During erection, precast members and struc- R16.9.2 — All temporary erection connections, bracing,
tures shall be adequately supported and braced to shoring as well as the sequencing of removal of these items
ensure proper alignment and structural integrity until are shown on contract or erection drawings.
permanent connections are completed.
16.10.1 — A precast element to be made composite The strength evaluation procedures of Chapter 20 are
with cast-in-place concrete shall be permitted to be applicable to precast members.
tested in flexure as a precast element alone in
accordance with 16.10.1.1 and 16.10.1.2.
CODE COMMENTARY
16.10.1.1 — Test loads shall be applied only when
calculations indicate the isolated precast element will
not be critical in compression or buckling.
16
CODE COMMENTARY
17.1 — Scope R17.1 — Scope
17.1.1 — Provisions of Chapter 17 shall apply for R17.1.1 — The scope of Chapter 17 is intended to include
design of composite concrete flexural members defined all types of composite concrete flexural members. In some
as precast concrete, cast-in-place concrete elements, or cases with fully cast-in-place concrete, it may be necessary
both, constructed in separate placements but so inter- to design the interface of consecutive placements of
connected that all elements respond to loads as a unit. concrete as required for composite members. Composite
structural steel-concrete members are not covered in this
chapter. Design provisions for such composite members are
covered in Reference 17.1.
17.2.4 — In strength computations of composite R17.2.4 — Tests have indicated that the strength of a
members, no distinction shall be made between composite member is the same whether or not the first element
shored and unshored members. cast is shored during casting and curing of the second element.
17.2.6 — Reinforcement shall be provided as required R17.2.6 — The extent of cracking is dependent on such
to minimize cracking and to prevent separation of factors as environment, aesthetics, and occupancy. In addition,
individual elements of composite members. composite action should not be impaired.
17.2.7 — Composite members shall meet requirements R17.2.7 — The premature loading of precast elements can
for control of deflections in accordance with 9.5.5. cause excessive creep and shrinkage deflections. This is
especially so at early ages when the moisture content is high
and the strength low.
CODE COMMENTARY
17.3 — Shoring R17.3 — Shoring
When used, shoring shall not be removed until The provisions of 9.5.5 cover the requirements pertaining to
supported elements have developed design properties deflections of shored and unshored members.
required to support all loads and limit deflections and
cracking at time of shoring removal.
17.5.1 — In a composite member, full transfer of R17.5.1 — Full transfer of horizontal shear between segments
horizontal shear forces shall be ensured at contact of composite members should be ensured by horizontal shear
surfaces of interconnected elements. strength at contact surfaces or properly anchored ties, or both.
17.5.2 — For the provisions of 17.5, d shall be taken R17.5.2 — Prestressed members used in composite
as the distance from extreme compression fiber for construction may have variations in depth of tension reinforce-
17 entire composite section to centroid of prestressed ment along member length due to draped or depressed
and nonprestressed longitudinal tension reinforce- tendons. Because of this variation, the definition of d used in
ment, if any, but need not be taken less than 0.80h for Chapter 11 for determination of vertical shear strength is
prestressed concrete members. also appropriate when determining horizontal shear strength.
17.5.3 — Unless calculated in accordance with 17.5.4, R17.5.3 — The nominal horizontal shear strengths Vnh apply
design of cross sections subject to horizontal shear when the design is based on the load factors and φ-factors of
shall be based on Chapter 9.
Vu ≤ φVnh (17-1)
CODE COMMENTARY
17.5.3.3 — Where ties are provided in accordance R17.5.3.3 — The permitted horizontal shear strengths
with 17.6, and contact surfaces are clean, free of and the requirement of 6 mm amplitude for intentional
laitance, and intentionally roughened to a full ampli- roughness are based on tests discussed in References 17.2
tude of approximately 6 mm, Vnh shall be taken equal through 17.4.
to (1.8 + 0.6ρvfy)λbvd, but not greater than 3.5bvd.
Values for λ in 11.6.4.3 shall apply and ρv is Av /(bvs).
17.5.4.1 — Where ties provided to resist horizontal R17.5.4.1 — The distribution of horizontal shear stresses
shear are designed to satisfy 17.5.4, the tie area to tie along the contact surface in a composite member will reflect
spacing ratio along the member shall approximately the distribution of shear along the member. Horizontal shear
reflect the distribution of shear forces in the member. failure will initiate where the horizontal shear stress is a
maximum and will spread to regions of lower stress.
Because the slip at peak horizontal shear resistance is small
for a concrete-to-concrete contact surface, longitudinal
redistribution of horizontal shear resistance is very limited.
The spacing of the ties along the contact surface should,
therefore, be such as to provide horizontal shear resistance
distributed approximately as the shear acting on the member 17
is distributed.
17.5.5 — Where tension exists across any contact R17.5.5 — Proper anchorage of ties extending across inter-
surface between interconnected elements, shear faces is required to maintain contact of the interfaces.
transfer by contact shall be permitted only when
minimum ties are provided in accordance with 17.6.
17.6 — Ties for horizontal shear R17.6 — Ties for horizontal shear
17.6.1 — Where ties are provided to transfer hori- The minimum areas and maximum spacings are based on
zontal shear, tie area shall not be less than that test data given in References 17.2 through 17.6.
required by 11.4.6.3, and tie spacing shall not exceed
four times the least dimension of supported element,
nor exceed 600 mm.
17
CODE COMMENTARY
18.1 — Scope R18.1 — Scope
18.1.1 — Provisions of Chapter 18 shall apply to R18.1.1 — The provisions of Chapter 18 were developed
members prestressed with wire, strands, or bars primarily for structural members such as slabs, beams, and
conforming to provisions for prestressing steel in 3.5.6. columns that are commonly used in buildings. Many of the
provisions may be applied to other types of construction,
such as pressure vessels, pavements, pipes, and crossties.
Application of the provisions is left to the judgment of the
licensed design professional in cases not specifically cited
in the Code.
18.1.2 — All provisions of this Code not specifically
excluded, and not in conflict with provisions of Chapter 18,
shall apply to prestressed concrete.
18.1.3 — The following provisions of this Code shall R18.1.3 — Some sections of the Code are excluded from
not apply to prestressed concrete, except as specifi- use in the design of prestressed concrete for specific
cally noted: Sections 6.4.4, 7.6.5, 8.12.2, 8.12.3, reasons. The following discussion provides explanation for
8.12.4, 8.13, 10.5, 10.6, 10.9.1, and 10.9.2; Chapter 13; such exclusions:
and Sections 14.3, 14.5, and 14.6, except that certain
sections of 10.6 apply as noted in 18.4.4. Section 6.4.4 — Tendons of continuous post-tensioned
beams and slabs are usually stressed at a point along the
span where the tendon profile is at or near the centroid of
the concrete cross section. Therefore, interior construction
joints are usually located within the end thirds of the span,
rather than the middle third of the span as required by 6.4.4.
Construction joints located as described in continuous post-
tensioned beams and slabs have a long history of satisfactory
performance. Thus, 6.4.4 is excluded from application to
prestressed concrete. 18
CODE COMMENTARY
Sections 8.12.1 and 8.12.5 provide general requirements for
T-beams that are also applicable to prestressed concrete
members. The spacing limitations for slab reinforcement are
based on flange thickness, which for tapered flanges can be
taken as the average thickness.
18.2.1 — Prestressed members shall meet the R18.2.1 and R18.2.2 — The design investigation should
strength requirements of this Code. include all stages that may be significant. The three major
stages are: (1) jacking stage, or prestress transfer stage—
18.2.2 — Design of prestressed members shall be when the tensile force in the prestressing steel is transferred
based on strength and on behavior at service condi- to the concrete and stress levels may be high relative to
tions at all stages that will be critical during the life of concrete strength; (2) service load stage—after long-term
the structure from the time prestress is first applied. volume changes have occurred; and (3) the factored load
stage—when the strength of the member is checked. There
may be other load stages that require investigation. For
example, if the cracking load is significant, this load stage
may require study, or the handling and transporting stage
may be critical.
CODE COMMENTARY
Service load stage refers to the loads defined in the general
building code (without load factors), such as live load and
dead load, while the factored load stage refers to loads
multiplied by the appropriate load factors.
18.2.6 — In computing section properties before R18.2.6 — In considering the area of the open ducts, the
bonding of prestressing steel, effect of loss of area due critical sections should include those that have coupler
to open ducts shall be considered. sheaths that may be of a larger size than the duct containing
the prestressing steel. Also, in some instances, the trumpet
or transition piece from the conduit to the anchorage may be
18
of such a size as to create a critical section. If the effect of
the open duct area on design is deemed negligible, section
properties may be based on total area.
CODE COMMENTARY
18.3.2.1 — Strains vary linearly with depth through
the entire load range.
18.3.3 — Prestressed flexural members shall be classi- R18.3.3 — This section defines three classes of behavior of
fied as Class U, Class T, or Class C based on ft , the prestressed flexural members. Class U members are
computed extreme fiber stress in tension in the assumed to behave as uncracked members. Class C
precompressed tensile zone calculated at service members are assumed to behave as cracked members. The
loads, as follows: behavior of Class T members is assumed to be in transition
between uncracked and cracked. The serviceability require-
(a) Class U: ft ≤ 0.62 f c′ ments for each class are summarized in Table R18.3.3. For
(b) Class T: 0.62 f c′ < ft ≤ 1.0 f c′ comparison, Table R18.3.3 also shows corresponding
(c) Class C: ft > 1.0 f c′ requirements for nonprestressed members.
Prestressed two-way slab systems shall be designed These classes apply to both bonded and unbonded
as Class U with ft ≤ 0.50 f c′ . prestressed flexural members, but prestressed two-way slab
systems must be designed as Class U.
18.3.4 — For Class U and Class T flexural members, R18.3.4 — A method for computing stresses in a cracked
stresses at service loads shall be permitted to be section is given in Reference 18.1.
calculated using the uncracked section. For Class C
flexural members, stresses at service loads shall be
calculated using the cracked transformed section.
18
18.3.5 — Deflections of prestressed flexural members R18.3.5 — Reference 18.2 provides information on
shall be calculated in accordance with 9.5.4. computing deflections of cracked members.
18.4.1 — Stresses in concrete immediately after R18.4.1 — The concrete stresses at this stage are caused by the
prestress transfer (before time-dependent prestress force in the prestressing steel at transfer reduced by the losses
losses): due to elastic shortening of the concrete, relaxation of the
prestressing steel, seating at transfer, and the stresses due to the
(a) Extreme fiber stress in compression except as weight of the member. Generally, shrinkage and creep effects
permitted in (b) shall not exceed ................ 0.60fci′ are not included at this stage. These stresses apply to both
pretensioned and post-tensioned concrete with proper modifi-
(b) Extreme fiber stress in compression at ends of
cations of the losses at transfer. The compressive transfer stress
simply support members shall not exceed ...... 0.70fci′
at ends of simply supported members was raised from 0.60fci′
(c) Where computed concrete tensile strength, ft , to 0.70fci′ in the 2008 Code to reflect research in the precast,
exceeds 0.5 f ci′ at ends of simply supported prestressed concrete industry practice.18.3-18.5
CODE COMMENTARY
TABLE R18.3.3 — SERVICEABILITY DESIGN REQUIREMENTS
Prestressed
Class U Class T Class C Nonprestressed
Transition between
Assumed behavior Uncracked Cracked Cracked
uncracked and cracked
Section properties for stress calculation at
Gross section 18.3.4 Gross section 18.3.4 Cracked section 18.3.4 No requirement
service loads
Allowable stress at transfer 18.4.1 18.4.1 18.4.1 No requirement
Allowable compressive stress based on
uncracked section properties 18.4.2 18.4.2 No requirement No requirement
Tensile stress at service loads 18.3.3 ≤ 0.62 f c ′ 0.62 f c ′ < ft ≤ fc ′ No requirement No requirement
members, or 0.25 f ci′ at other locations, additional R18.4.1(c) — The tension stress limits of 0.25 f ci ′ and
bonded reinforcement shall be provided in the ′ refer to tensile stress at locations other than the
0.5 f ci
tensile zone to resist the total tensile force in precompressed tensile zone. Where tensile stresses exceed the
concrete computed with the assumption of an permissible values, the total force in the tensile stress zone
uncracked section. may be calculated and reinforcement proportioned on the basis
of this force at a stress of 0.6 fy , but not more than 210 MPa.
The effects of creep and shrinkage begin to reduce the tensile
stress almost immediately; however, some tension remains in
these areas after allowance is made for all prestress losses.
18.4.2 — For Class U and Class T prestressed flexural R18.4.2(a) and (b) — The compression stress limit of 0.45fc′
members, stresses in concrete at service loads (based was conservatively established to decrease the probability of
on uncracked section properties, and after allowance failure of prestressed concrete members due to repeated
for all prestress losses) shall not exceed the following: loads. This limit seemed reasonable to preclude excessive
creep deformation. At higher values of stress, creep strains
(a) Extreme fiber stress in compression due tend to increase more rapidly as applied stress increases. 18
to prestress plus sustained load.................... 0.45fc′
The change in allowable stress in the 1995 Code recognized
(b) Extreme fiber stress in compression due that fatigue tests of prestressed concrete beams have shown
to prestress plus total load ............................ 0.60fc′ that concrete failures are not the controlling criterion.
Designs with transient live loads that are large compared to
sustained live and dead loads have been penalized by the
previous single compression stress limit. Therefore, the
stress limit of 0.60fc′ permits a one-third increase in allowable
compression stress for members subject to transient loads.
CODE COMMENTARY
18.4.3 — Permissible stresses in 18.4.1 and 18.4.2 R18.4.3 — This section provides a mechanism whereby
shall be permitted to be exceeded if shown by test or development of new products, materials, and techniques in
analysis that performance will not be impaired. prestressed concrete construction need not be inhibited by
Code limits on stress. Approvals for the design should be in
accordance with 1.4 of the Code.
18.4.4 — For Class C prestressed flexural members R18.4.4 — Spacing requirements for prestressed members
not subject to fatigue or to aggressive exposure, the with calculated tensile stress exceeding 1.0 f c′ were intro-
spacing of bonded reinforcement nearest the extreme duced in the 2002 edition of the Code.
tension face shall not exceed that given by 10.6.4.
For conditions of corrosive environments, defined as an
For structures subject to fatigue or exposed to corrosive environment in which chemical attack (such as seawater,
environments, investigations and precautions are corrosive industrial atmosphere, or sewer gas) is encountered,
required. cover greater than that required by 7.7.2 should be used, and
tension stresses in the concrete reduced to eliminate
possible cracking at service loads. Judgment should be used
to determine the amount of increased cover and whether
reduced tension stresses are required.
18.4.4.1 — The spacing requirements shall be met R18.4.4.1 — Only tension steel nearest the tension face need
by nonprestressed reinforcement and bonded tendons. be considered in selecting the value of cc used in computing
The spacing of bonded tendons shall not exceed 2/3 of spacing requirements. To account for prestressing steel, such as
the maximum spacing permitted for nonprestressed strand, having bond characteristics less effective than deformed
reinforcement. reinforcement, a 2/3 effectiveness factor is used.
Where both reinforcement and bonded tendons are For post-tensioned members designed as cracked members,
used to meet the spacing requirement, the spacing it will usually be advantageous to provide crack control by
between a bar and a tendon shall not exceed 5/6 of the use of deformed reinforcement, for which the provisions
that permitted by 10.6.4. See also 18.4.4.3. of 10.6 may be used directly. Bonded reinforcement
required by other provisions of this Code may also be used
as crack control reinforcement.
18.4.4.2 — In applying Eq. (10-4) to prestressing R18.4.4.2 — It is conservative to take the decompression
18 tendons, Δfps shall be substituted for fs , where Δfps stress fdc equal to fse, the effective stress in the prestressing
shall be taken as the calculated stress in the steel.
prestressing steel at service loads based on a cracked
section analysis minus the decompression stress fdc .
It shall be permitted to take fdc equal to the effective
stress in the prestressing steel fse . See also 18.4.4.3.
18.4.4.3 — In applying Eq. (10-4) to prestressing R18.4.4.3 — The maximum limitation of 250 MPa for
tendons, the magnitude of Δfps shall not exceed Δfps and the exemption for members with Δ fps less than
250 MPa. When Δfps is less than or equal to 140 MPa, 140 MPa are intended to be similar to the Code require-
the spacing requirements of 18.4.4.1 and 18.4.4.2 ments before the 2002 edition.
shall not apply.
18.4.4.4 — Where h of a beam exceeds 900 mm, R18.4.4.4 — The steel area of reinforcement, bonded
the area of longitudinal skin reinforcement consisting tendons, or a combination of both may be used to satisfy
of reinforcement or bonded tendons shall be provided this requirement.
as required by 10.6.7.
CODE COMMENTARY
18.5 — Permissible stresses in prestressing R18.5 — Permissible stresses in prestressing
steel steel
18.6.1 — To determine effective stress in the R18.6.1 — For an explanation of how to compute prestress
prestressing steel, fse , allowance for the following losses, see References 18.6 through 18.9. Lump sum values
sources of loss of prestress shall be considered: of prestress losses for both pretensioned and post-tensioned
members that were indicated before the 1983 Commentary
(a) Prestressing steel seating at transfer; are considered obsolete. Reasonably accurate estimates of
prestress losses can be calculated in accordance with the
(b) Elastic shortening of concrete; recommendations in Reference 18.9, which include consider-
CODE COMMENTARY
(c) Creep of concrete; ation of initial stress level (0.7fpu or higher), type of steel
(stress-relieved or low-relaxation wire, strand, or bar), exposure
(d) Shrinkage of concrete; conditions, and type of construction (pretensioned, bonded
(e) Relaxation of prestressing steel stress; post-tensioned, or unbonded post-tensioned).
(f) Friction loss due to intended or unintended Actual losses, greater or smaller than the computed values,
curvature in post-tensioning tendons. have little effect on the design strength of the member, but
affect service load behavior (deflections, camber, cracking
load) and connections. At service loads, overestimation of
prestress losses can be almost as detrimental as underestima-
tion, since the former can result in excessive camber and
horizontal movement.
18.6.2 — Friction loss in post-tensioning tendons R18.6.2 — Friction loss in post-tensioning tendons
18.6.2.1 — Ppx , force in post-tensioning tendons a The coefficients tabulated in Table R18.6.2 give a range that
distance lpx from the jacking end shall be computed by generally can be expected. Due to the many types of
prestressing steel ducts and sheathing available, these values
– ( Kl px + μ p α px ) can only serve as a guide. Where rigid conduit is used, the
Ppx = Ppj e (18-1) wobble coefficient K can be considered as zero. For large-
diameter prestressing steel in semirigid type conduit, the
Where (Klpx + μpαpx) is not greater than 0.3, Ppx shall wobble factor can also be considered zero. Values of the
be permitted to be computed by coefficients to be used for the particular types of
prestressing steel and particular types of ducts should be
Ppx = Ppj (1 + Klpx + μpαpx)–1 (18-2) obtained from the manufacturers of the tendons. An unreal-
istically low evaluation of the friction loss can lead to
18.6.2.2 — Friction loss shall be based on experi- improper camber of the member and inadequate prestress.
mentally determined wobble K and curvature μp friction Overestimation of the friction may result in extra
coefficients, and shall be verified during tendon prestressing force. This could lead to excessive camber and
stressing operations. excessive shortening of a member. If the friction factors are
determined to be less than those assumed in the design, the
tendon stressing should be adjusted to give only that
prestressing force in the critical portions of the structure
18 required by the design.
CODE COMMENTARY
18.6.2.3 — Values of K and μp used in design shall R18.6.2.3 — When the safety or serviceability of the
be shown on design drawings. structure may be involved, the acceptable range of
prestressing steel jacking forces or other limiting requirements
should either be given or approved by the licensed design
professional in conformance with the permissible stresses of
18.4 and 18.5.
18.7.1 — Design moment strength of flexural R18.7.1 — Design moment strength of prestressed flexural
members shall be computed by the strength design members may be computed using strength equations similar
methods of the Code. For prestressing steel, fps shall to those for nonprestressed concrete members. The 1983
be substituted for fy in strength computations. Code provided strength equations for rectangular and
flanged sections, with tension reinforcement only and with
tension and compression reinforcement. When part of the
prestressing steel is in the compression zone, a method
based on applicable conditions of equilibrium and compati-
bility of strains at a factored load condition should be used.
18.7.2 — As an alternative to a more accurate R18.7.2 — Equation (18-3) may underestimate the strength
determination of fps based on strain compatibility, the of beams with high percentages of reinforcement and, for
following approximate values of fps shall be permitted more accurate evaluations of their strength, the strain
to be used if fse is not less than 0.5fpu . compatibility and equilibrium method should be used. Use
of Eq. (18-3) is appropriate when all of the prestressed
18
(a) For members with bonded tendons reinforcement is in the tension zone. When part of the
prestressed reinforcement is in the compression zone, a
strain compatibility and equilibrium method should be used.
⎧ γp f pu d ⎫
fps = fpu ⎪⎨ 1 – -----
β1
- ρ p -------- + ------ ( ω – ω′ )
fc ′ dp
⎪
⎬ (18-3)
By inclusion of the ω′ term, Eq. (18-3) reflects the increased
value of fps obtained when compression reinforcement is
⎪ ⎪
⎩ ⎭ provided in a beam with a large reinforcement index. When
the term [ρp (fpu /fc′ ) + (d/dp)(ω – ω′)] in Eq. (18-3) is small,
where ω is ρfy /fc′ , ω′ is ρ′fy /fc′ , and γp is 0.55 for the neutral axis depth is small, the compressive reinforce-
fpy /fpu not less than 0.80; 0.40 for fpy /fpu not less ment does not develop its yield strength, and Eq. (18-3)
than 0.85; and 0.28 for fpy /fpu not less than 0.90. becomes unconservative. This is the reason why the term
[ρp (fpu /fc′ ) + (d/dp)(ω – ω′)] in Eq. (18-3) may not be taken
If any compression reinforcement is taken into less than 0.17 if compression reinforcement is taken into
account when calculating fps by Eq. (18-3), the term account when computing fps. If the compression reinforce-
ment is neglected when using Eq. (18-3), ω′ is taken as zero,
f pu d then the term [ρp(fpu /fc′ ) + (d/dp)ω] may be less than 0.17
ρ p -------
- + ------ ( ω – ω′ ) and an increased and correct value of fps is obtained.
fc ′ dp
When d′ is large, the strain in compression reinforcement
shall be taken not less than 0.17 and d ′ shall be no can be considerably less than its yield strain. In such a case,
greater than 0.15dp . the compression reinforcement does not influence fps as
CODE COMMENTARY
(b) For members with unbonded tendons and with a favorably as implied by Eq. (18-3). For this reason, the
span-to-depth ratio of 35 or less: applicability of Eq. (18-3) is limited to beams in which d′ is
less than or equal to 0.15dp.
f c′ The term [ρp (fpu /fc′ ) + (d/dp)(ω _ ω′)] in Eq. (18-3) may
f ps = f se + 70 + ---------------- (18-4)
100ρ p also be written [ρp (fpu /fc′ ) + As fy /(bdp fc′) _ As′fy /(bdp fc′)].
This form may be more convenient, such as when there is no
but fps in Eq. (18-4) shall not be taken greater than unprestressed tension reinforcement.
the lesser of fpy and (fse + 420). Equation (18-5) reflects results of tests on members with
(c) For members with unbonded tendons and with a unbonded tendons and span-to-depth ratios greater than 35
span-to-depth ratio greater than 35: (one-way slabs, flat plates, and flat slabs).18.10 These tests also
indicate that Eq. (18-4), formerly used for all span-depth ratios,
overestimates the amount of stress increase in such members.
f c′
f ps = f se + 70 + ---------------- (18-5) Although these same tests indicate that the moment strength of
300ρ p those shallow members designed using Eq. (18-4) meets the
factored load strength requirements, this reflects the effect of
but fps in Eq. (18-5) shall not be taken greater than the Code requirements for minimum bonded reinforcement, as
the lesser of fpy and (fse + 210). well as the limitation on concrete tensile stress that often
controls the amount of prestressing force provided.
18.8 — Limits for reinforcement of flexural R18.8 — Limits for reinforcement of flexural
members members
18 18.8.1 — Prestressed concrete sections shall be R18.8.1 — The net tensile strain limits for compression- and
classified as either tension-controlled, transition, or tension-controlled sections given in 10.3.3 and 10.3.4 apply
compression-controlled sections, in accordance with to prestressed sections. These provisions take the place of
10.3.3 and 10.3.4. The appropriate strength reduction maximum reinforcement limits used in the 1999 Code.
factors, φ, from 9.3.2 shall apply.
The net tensile strain limits for tension-controlled sections
given in 10.3.4 may also be stated in terms of ωp as defined
in the 1999 and earlier editions of the Code. The net tensile
strain limit of 0.005 corresponds to ωp = 0.32β1 for
prestressed rectangular sections.
18.8.2 — Total amount of prestressed and nonpre- R18.8.2 — This provision is a precaution against abrupt flex-
stressed reinforcement in members with bonded ural failure developing immediately after cracking. A flexural
prestressed reinforcement shall be adequate to member designed according to Code provisions requires
develop a factored load at least 1.2 times the cracking considerable additional load beyond cracking to reach its
load computed on the basis of the modulus of rupture flexural strength. Thus, considerable deflection would warn
fr specified in 9.5.2.3. This provision shall be permitted that the member strength is approaching. If the flexural
to be waived for flexural members with shear and strength were reached shortly after cracking, the warning
flexural strength at least twice that required by 9.2. deflection would not occur. Transfer of force between the
concrete and the prestressing steel, and abrupt flexural failure
immediately after cracking, does not occur when the
prestressing steel is unbonded18.11; therefore, this require-
ment does not apply to members with unbonded tendons.
CODE COMMENTARY
18.8.3 — Part or all of the bonded reinforcement R18.8.3 — Some bonded steel is required to be placed near
consisting of bars or tendons shall be provided as the tension face of prestressed flexural members. The
close as practicable to the tension face in prestressed purpose of this bonded steel is to control cracking under full
flexural members. In members prestressed with service loads or overloads.
unbonded tendons, the minimum bonded reinforce-
ment consisting of bars or tendons shall be as
required by 18.9.
18.9.1 — A minimum area of bonded reinforcement R18.9.1 — Some bonded reinforcement is required by the
shall be provided in all flexural members with unbonded Code in members prestressed with unbonded tendons to ensure
tendons as required by 18.9.2 and 18.9.3. flexural performance at ultimate member strength, rather than
as a tied arch, and to limit crack width and spacing at service
load when concrete tensile stresses exceed the modulus of
rupture. Providing the minimum bonded reinforcement as
stipulated in 18.9 helps to ensure adequate performance.
18.9.2 — Except as provided in 18.9.3, minimum area R18.9.2 — The minimum amount of bonded reinforcement
of bonded reinforcement shall be computed by for members other than two-way flat slab systems is based
on research comparing the behavior of bonded and 18
As = 0.004Act (18-6) unbonded post-tensioned beams.18.12 Based on this
research, it is advisable to apply the provisions of 18.9.2
where Act is area of that part of cross section between also to one-way slab systems.
the flexural tension face and center of gravity of gross
section.
18.9.3 — For two-way flat slab systems, minimum area R18.9.3 — The minimum amount of bonded reinforcement
and distribution of bonded reinforcement shall be as in two-way flat slab systems is based on reports by Joint
required in 18.9.3.1, 18.9.3.2, and 18.9.3.3. ACI-ASCE Committee 423.18.6,18.11 Limited research avail-
able for two-way flat slabs with drop panels18.13 indicates
that behavior of these particular systems is similar to the
behavior of flat plates. Reference 18.11 was revised by
Committee 423 in 1983 to clarify that Section 18.9.3 applies
to two-way flat slab systems.
CODE COMMENTARY
18.9.3.1 — Bonded reinforcement shall not be R18.9.3.1 — For usual loads and span lengths, flat plate
required in positive moment areas where ft , the tests summarized in the Committee 423 report18.3 and
extreme fiber stress in tension in the precompressed experience since the 1963 Code was adopted indicate
tensile zone at service loads, (after allowance for all satisfactory performance without bonded reinforcement in
prestress losses) does not exceed 0.17 f c′ . the areas described in 18.9.3.1.
18.9.3.2 — In positive moment areas where R18.9.3.2 — In positive moment areas, where the
computed tensile stress in concrete at service load concrete tensile stresses are between 0.17 f c′ and
exceeds 0.17 f c′ , minimum area of bonded reinforce- 0.5 f c′ , a minimum bonded reinforcement area proportioned
ment shall be computed by according to Eq. (18-7) is required. The tensile force Nc is
computed at service load on the basis of an uncracked,
Nc homogeneous section.
A s = ------------
- (18-7)
0.5f y
18.9.3.3 — In negative moment areas at column R18.9.3.3 — Research on unbonded post-tensioned two-way
supports, the minimum area of bonded reinforcement flat slab systems evaluated by Committee 42318.1,18.6,18.11,18.13
As in the top of the slab in each direction shall be shows that bonded reinforcement in negative moment
computed by regions, proportioned on the basis of 0.075 percent of the
cross-sectional area of the slab-beam strip, provides sufficient
As = 0.00075Acf (18-8) ductility and reduces crack width and spacing. To account for
different adjacent tributary spans, Eq. (18-8) is given on the
where Acf is the larger gross cross-sectional area of basis of the equivalent frame as defined in 13.7.2 and pictured
the slab-beam strips in two orthogonal equivalent in Fig. R13.7.2. For rectangular slab panels, Eq. (18-8) is
frames intersecting at a column in a two-way slab. conservatively based upon the larger of the cross-sectional
areas of the two intersecting equivalent frame slab-beam
Bonded reinforcement required by Eq. (18-8) shall be strips at the column. This ensures that the minimum
distributed between lines that are 1.5h outside opposite percentage of steel recommended by research is provided in
18 faces of the column support. At least four bars or wires both directions. Concentration of this reinforcement in the top
shall be provided in each direction. Spacing of bonded of the slab directly over and immediately adjacent to the
reinforcement shall not exceed 300 mm. column is important. Research also shows that where low
tensile stresses occur at service loads, satisfactory behavior
has been achieved at factored loads without bonded reinforce-
ment. However, the Code requires minimum bonded rein-
forcement regardless of service load stress levels to help
ensure flexural continuity and ductility, and to limit crack
widths and spacing due to overload, temperature, or
shrinkage. Research on post-tensioned flat plate-to-column
connections is reported in References 18.14 through 18.18.
18.9.4 — Minimum length of bonded reinforcement R18.9.4 — Bonded reinforcement should be adequately
required by 18.9.2 and 18.9.3 shall be as required in anchored to develop factored load forces. The requirements
18.9.4.1, 18.9.4.2, and 18.9.4.3. of Chapter 12 will ensure that bonded reinforcement
required for flexural strength under factored loads in accor-
18.9.4.1 — In positive moment areas, minimum length dance with 18.7.3, or for tensile stress conditions at service
of bonded reinforcement shall be one-third the clear span load in accordance with 18.9.3.2, will be adequately
length, ln , and centered in positive moment area. anchored to develop tension or compression forces. The
minimum lengths apply for bonded reinforcement required
18.9.4.2 — In negative moment areas, bonded by 18.9.2 or 18.9.3.3, but not required for flexural strength
reinforcement shall extend one-sixth the clear span, in accordance with 18.7.3. Research18.13 on continuous
ln , on each side of support. spans shows that these minimum lengths provide adequate
behavior under service load and factored load conditions.
ACI 318 Building Code and Commentary
CHAPTER 18 293
CODE COMMENTARY
18.9.4.3 — Where bonded reinforcement is provided
for φMn in accordance with 18.7.3, or for tensile stress
conditions in accordance with 18.9.3.2, minimum length
also shall conform to provisions of Chapter 12.
18.10.3 — Moments used to compute required R18.10.3 — For statically indeterminate structures, the
strength shall be the sum of the moments due to moments due to reactions induced by prestressing forces,
reactions induced by prestressing (with a load factor of referred to as secondary moments, are significant in both the
1.0) and the moments due to factored loads. Adjust- elastic and inelastic states (see References 18.19 through
ment of the sum of these moments shall be permitted 18.21). The elastic deformations caused by a nonconcordant
as allowed in 18.10.4. tendon change the amount of inelastic rotation required to
obtain a given amount of moment redistribution.
Conversely, for a beam with a given inelastic rotational
capacity, the amount by which the moment at the support
may be varied is changed by an amount equal to the
secondary moment at the support due to prestressing. Thus,
the Code requires that secondary moments be included in
determining design moments.
18.10.4.1 — Where bonded reinforcement is The provisions for redistribution of moments given in 8.4
provided at supports in accordance with 18.9, it shall apply equally to prestressed members. See Reference 18.22
be permitted to decrease negative or positive for a comparison of research results and to Section 18.10.4
moments calculated by elastic theory for any assumed of the 1999 Code.
loading, in accordance with 8.4.
For the moment redistribution principles of 18.10.4 to be
18.10.4.2 — The reduced moment shall be used for applicable to beams with unbonded tendons, it is necessary
calculating redistributed moments at all other sections that such beams contain sufficient bonded reinforcement to
within the spans. Static equilibrium shall be main- ensure they will act as beams after cracking and not as a
tained after redistribution of moments for each loading series of tied arches. The minimum bonded reinforcement
arrangement. requirements of 18.9 serves this purpose.
ACI 318 Building Code and Commentary
294 CHAPTER 18
CODE COMMENTARY
18.11 — Compression members — R18.11 — Compression members —
Combined flexure and axial loads Combined flexure and axial loads
18.11.2 — Limits for reinforcement of prestressed R18.11.2 — Limits for reinforcement of prestressed
compression members compression members
18.11.2.3 — For walls with average compressive R18.11.2.3 — The minimum amounts of reinforcement in
stress in concrete due to effective prestress force only 14.3 need not apply to prestressed concrete walls, provided
equal to or greater than 1.6 MPa, minimum reinforce- the average compressive stress in concrete due to effective
ment required by 14.3 shall not apply where structural prestress force only is 1.6 MPa or greater and a structural
analysis shows adequate strength and stability. analysis is performed to show adequate strength and
stability with lower amounts of reinforcement.
18.12.1 — Factored moments and shears in R18.12.1 — Use of the equivalent frame method of analysis
prestressed slab systems reinforced for flexure in (see 13.7) or more precise analysis procedures is required
more than one direction shall be determined in accor- for determination of both service and factored moments and
dance with provisions of 13.7 (excluding 13.7.7.4 and shears for prestressed slab systems. The equivalent frame
13.7.7.5), or by more detailed design procedures. method of analysis has been shown by tests of large structural
CODE COMMENTARY
models to satisfactorily predict factored moments and
shears in prestressed slab systems. (See References 18.14
through 18.16, and 18.23 through 18.25.) The referenced
research also shows that analysis using prismatic sections or
other approximations of stiffness may provide erroneous
results on the unsafe side. Section 13.7.7.4 is excluded from
application to prestressed slab systems because it relates to
reinforced slabs designed by the direct design method, and
because moment redistribution for prestressed slabs is
covered in 18.10.4. Section 13.7.7.5 does not apply to
prestressed slab systems because the distribution of
moments between column strips and middle strips required
by 13.7.7.5 is based on tests for nonprestressed concrete
slabs. Simplified methods of analysis using average coeffi-
cients do not apply to prestressed concrete slab systems.
18.12.2 — φMn of prestressed slabs required by 9.3 at R18.12.2 — Tests indicate that the moment and shear
every section shall be greater than or equal to Mu consid- strength of prestressed slabs is controlled by total prestessing
ering 9.2, 18.10.3, and 18.10.4. φVn of prestressed slabs steel strength and by the amount and location of nonprestressed
at columns required by 9.3 shall be greater than or equal reinforcement, rather than by tendon distribution. (See Refer-
to Vu considering 9.2, 11.1, 11.11.2, and 11.11.6.2. ences 18.14 through 18.16, and 18.23 through 18.25.)
18.12.3 — At service load conditions, all service- R18.12.3 — For prestressed flat slabs continuous over two or
ability limitations, including limits on deflections, shall more spans in each direction, the span-thickness ratio generally
be met, with appropriate consideration of the factors should not exceed 42 for floors and 48 for roofs; these limits
listed in 18.10.2. may be increased to 48 and 52, respectively, if calculations
verify that both short- and long-term deflection, camber, and
vibration frequency and amplitude are not objectionable.
18.12.4 — For uniformly distributed loads, spacing of R18.12.4 — This section provides specific guidance
tendons or groups of tendons in at least one direction concerning tendon distribution that will permit the use of
shall not exceed the smaller of eight times the slab banded tendon distributions in one direction. This method of
thickness and 1.5 m. Spacing of tendons also shall tendon distribution has been shown to provide satisfactory
provide a minimum average effective prestress of performance by structural research. The minimum average
0.9 MPa on the slab section tributary to the tendon or effective prestress of 0.9 MPa was used in two-way test panels
tendon group. For slabs with varying cross section in the early 70s to address punching shear concerns of
along the slab span, either parallel or perpendicular to lightly reinforced slabs. For this reason, the minimum effec-
the tendon or tendon group, the minimum average tive prestress must be provided at every cross section.
effective prestress of 0.9 MPa is required at every cross
section tributary to the tendon or tendon group along If the slab thickness varies along the span of a slab or
the span. Concentrated loads and opening in slabs perpendicular to the span of a slab, resulting in a varying
shall be considered when determining tendon spacing. slab cross section, the 0.9 MPa minimum effective prestress
and the maximum tendon spacing is required at every cross
section tributary to the tendon or group of tendons along the
span, considering both the thinner and the thicker slab
sections. Note that this may result in higher than the
minimum fpc in thinner cross sections, and tendons spaced
CODE COMMENTARY
at less than the maximum in thicker cross sections along a
span with varying thickness, due to the practical aspects of
tendon placement in the field.
18.12.6 — Except as permitted in 18.12.7, in slabs R18.12.6 — Unbonded prestressing tendons that pass
with unbonded tendons, a minimum of two 12.7 mm through the slab-column joint at any location over the depth
diameter or larger, seven-wire post-tensioned strands of the slab suspend the slab following a punching shear
shall be provided in each direction at columns, either failure, provided the tendons are continuous through or
passing through or anchored within the region anchored within the region bounded by the longitudinal
bounded by the longitudinal reinforcement of the reinforcement of the column and are prevented from
column. Outside column and shear cap faces, these bursting through the top surface of the slab.18.26 Between
two structural integrity tendons shall pass under any column or shear cap faces, structural integrity tendons
orthogonal tendons in adjacent spans. Where the two should pass below the orthogonal tendons from adjacent
structural integrity tendons are anchored within the spans so that vertical movements of the integrity tendons are
region bounded by the longitudinal reinforcement of the restrained by the orthogonal tendons. Where tendons are
column, the anchorage shall be located beyond the distributed in one direction and banded in the orthogonal
column centroid and away from the anchored span. direction, this requirement can be satisfied by first placing
the integrity tendons for the distributed tendon direction and
then placing the banded tendons. Where tendons are
distributed in both directions, weaving of tendons is necessary
and use of 18.12.7 may be an easier approach.
18.12.7 — Prestressed slabs not satisfying 18.12.6 R18.12.7 — In some prestressed slabs, tendon layout
shall be permitted provided they contain bottom constraints make it difficult to provide the structural integrity
reinforcement in each direction passing within the tendons required by 18.12.6. In such situations, the structural
region bounded by the longitudinal reinforcement of integrity tendons can be replaced by deformed bar bottom
the column and anchored at exterior supports as reinforcement.18.26
required by 13.3.8.5. The area of bottom reinforce-
ment in each direction shall be not less than 1.5 times
18 that required by Eq. (10-3) and not less than 2.1bwd/fy ,
where bw is the width of the column face through
which the reinforcement passes. Minimum extension
of these bars beyond the column or shear cap face
shall be equal to or greater than the bar development
length required by 12.2.1.
CODE COMMENTARY
The anchorage zone shall be considered as composed Based on the Principle of Saint-Venant, the extent of the
of two zones: anchorage zone may be estimated as approximately equal to
the largest dimension of the cross section. Local zones and
(a) The local zone is the rectangular prism (or equiva- general zones are shown in Fig. R18.13.1(a). When anchorage
lent rectangular prism for circular or oval anchorages) devices located away from the end of the member are tensioned,
of concrete immediately surrounding the anchorage large tensile stresses exist locally behind and ahead of the
device and any confining reinforcement; device. These tensile stresses are induced by incompatibility
CODE COMMENTARY
(b) The general zone is the anchorage zone as of deformations ahead of [as shown in Fig. R.18.13.1(b)] and
defined in 2.2 and includes the local zone. behind the anchorage device. The entire shaded region
should be considered, as shown in Fig. R18.13.1(b).
18.13.2.1 — Design of local zones shall be based The local zone resists the very high local stresses introduced
upon the factored prestressing force, Ppu, and the by the anchorage device and transfers them to the remainder
requirements of 9.2.5 and 9.3.2.5. of the anchorage zone. The behavior of the local zone is
strongly influenced by the specific characteristics of the
18.13.2.2 — Local-zone reinforcement shall be anchorage device and its confining reinforcement, and less
provided where required for proper functioning of the influenced by the geometry and loading of the overall
anchorage device. structure. Local-zone design sometimes cannot be
completed until specific anchorage devices are determined
18.13.2.3 — Local-zone requirements of 18.13.2.2 at the shop drawing stage. When special anchorage devices
are satisfied by 18.14.1 or 18.15.1 and 18.15.2. are used, the anchorage device supplier should furnish the
test information to show the device is satisfactory under
AASHTO “Standard Specifications for Highway Bridges,”
Division II, Article 10.3.2.3 and provide information
regarding necessary conditions for use of the device. The
main considerations in local-zone design are the effects of
the high bearing pressure and the adequacy of any confining
reinforcement provided to increase the capacity of the
concrete resisting bearing stresses.
18.13.3.1 — Design of general zones shall be based Within the general zone, the usual assumption of beam
upon the factored prestressing force, Ppu, and the theory that plane sections remain plane is not valid.
requirements of 9.2.5 and 9.3.2.5.
Design should consider all regions of tensile stresses that can
18.13.3.2 — General-zone reinforcement shall be be caused by the tendon anchorage device, including bursting,
provided where required to resist bursting, spalling, spalling, and edge tension as shown in Fig. R18.13.1(c). Also,
and longitudinal edge tension forces induced by the compressive stresses immediately ahead [as shown in
anchorage devices. Effects of abrupt change in section Fig. R18.13.1(b)] of the local zone should be checked.
shall be considered. Sometimes, reinforcement requirements cannot be deter-
mined until specific tendon and anchorage device layouts
18.13.3.3 — The general-zone requirements of are determined at the shop-drawing stage. Design and
18.13.3.2 are satisfied by 18.13.4, 18.13.5, 18.13.6 approval responsibilities should be clearly assigned in the
and whichever one of 18.14.2 or 18.14.3 or 18.15.3 is project drawings and specifications.
applicable.
Abrupt changes in section can cause substantial deviation in
force paths. These deviations can greatly increase tension
forces as shown in Fig. R18.13.3.
CODE COMMENTARY
18.13.4.1 — Tensile stress at nominal strength of Some inelastic deformation of concrete is expected because
bonded reinforcement is limited to fy for nonprestressed anchorage zone design is based on a strength approach. The
reinforcement and to fpy for prestressed reinforcement. low value for the nominal compressive strength for unconfined
Tensile stress at nominal strength of unbonded concrete reflects this possibility. For well-confined concrete, 18
prestressed reinforcement for resisting tensile forces the effective compressive strength could be increased (See
in the anchorage zone shall be limited to fps = fse + 70. Reference 18.28). The value for nominal tensile strength of
bonded prestressing steel is limited to the yield strength of
18.13.4.2 — Except for concrete confined within the prestressing steel because Eq. (18-3) may not apply to
spirals or hoops providing confinement equivalent to these nonflexural applications. The value for unbonded
that corresponding to Eq. (10-5), compressive strength prestressing steel is based on the values of 18.7.2(b) and (c),
in concrete at nominal strength in the general zone but is somewhat limited for these short-length, nonflexural
shall be limited to 0.7λfci′. applications. Test results given in Reference 18.28 indicate
that the compressive stress introduced by auxiliary
18.13.4.3 — Compressive strength of concrete at prestressing applied perpendicular to the axis of the main
time of post-tensioning shall be specified in the tendons is effective in increasing the anchorage zone
contract documents. Unless oversize anchorage strength. The inclusion of the λ factor for lightweight
devices are sized to compensate for the lower concrete reflects its lower tensile strength, which is an indirect
compressive strength or the prestressing steel is factor in limiting compressive stresses, as well as the wide
stressed to no more than 50 percent of the final scatter and brittleness exhibited in some lightweight
prestressing force, prestressing steel shall not be concrete anchorage zone tests.
stressed until compressive strength of concrete as
indicated by tests consistent with the curing of the To limit early shrinkage cracking, monostrand tendons are
member, is at least 28 MPa for multistrand tendons or sometimes stressed at concrete strengths less than 17 MPa.
at least 17 MPa for single-strand or bar tendons. In such cases, either oversized monostrand anchorages are
used, or the strands are stressed in stages, often to levels 1/3
to 1/2 the final prestressing force.
CODE COMMENTARY
18.13.5 — Design methods R18.13.5 — Design methods
18.13.5.1 — The following methods shall be The list of design methods in 18.13.5.1 includes those
permitted for the design of general zones provided that procedures for which fairly specific guidelines have been
the specific procedures used result in prediction of given in References 18.27 and 18.28. These procedures have
strength in substantial agreement with results of been shown to be conservative predictors of strength when
comprehensive tests: compared to test results.18.28 The use of strut-and-tie models
is especially helpful for general zone design.18.28 In many
(a) Equilibrium-based plasticity models (strut-and-tie anchorage applications, where substantial or massive
models); concrete regions surround the anchorages, simplified
equations can be used except in the cases noted in 18.13.5.2.
(b) Linear stress analysis (including finite element
analysis or equivalent); or For many cases, simplified equations based on References
(c) Simplified equations where applicable. 18.27 and 18.28 can be used. Values for the magnitude of the
bursting force, Tburst , and for its centroidal distance from the
18.13.5.2 — Simplified equations shall not be used major bearing surface of the anchorage, dburst , may be esti-
where member cross sections are nonrectangular, mated from Eq. (R18-1) and (R18-2), respectively. The terms
where discontinuities in or near the general zone of Eq. (R18-1) and (R18-2) are shown in Fig. R18.13.5 for a
cause deviations in the force flow path, where prestressing force with small eccentricity. In the applications
minimum edge distance is less than 1-1/2 times the of Eq. (R18-1) and (R18-2), the specified stressing sequence
anchorage device lateral dimension in that direction, or should be considered if more than one tendon is present.
where multiple anchorage devices are used in other
than one closely spaced group. h
T burst = 0.25ΣP pu ⎛ 1 – ----------
anc⎞
- (R18-1)
⎝ h ⎠
where
ΣPpu = the sum of the Ppu forces from the individual
tendons, N;
hanc = the depth of anchorage device or single group of
closely spaced devices in the direction considered,
18 mm;
eanc = the eccentricity (always taken as positive) of the
anchorage device or group of closely spaced
devices with respect to the centroid of the cross
section, mm;
h = the depth of the cross section in the direction
considered, mm.
CODE COMMENTARY
Anchorage devices should be treated as closely spaced if
their center-to-center spacing does not exceed 1.5 times the
width of the anchorage device in the direction considered.
The spalling force for tendons for which the centroid lies
within the kern of the section may be estimated as 2 percent
of the total factored prestressing force, except for multiple
anchorage devices with center-to-center spacing greater
than 0.4 times the depth of the section. For large spacings
and for cases where the centroid of the tendons is located
outside the kern, a detailed analysis is required. In addition,
in the post-tensioning of thin sections, or flanged sections, or
irregular sections, or when the tendons have appreciable
curvature within the general zone, more general procedures
such as those of AASHTO Articles 9.21.4 and 9.21.5 will be
required. Detailed recommendations for design principles
that apply to all design methods are given in Article 9.21.3.4
of Reference 18.27.
18.13.5.3 — The stressing sequence shall be specified R18.13.5.3 — The sequence of anchorage device
on the design drawings and considered in the design. stressing can have a significant effect on the general zone
stresses. Therefore, it is important to consider not only the
final stage of a stressing sequence with all tendons stressed,
but also intermediate stages during construction. The most
critical bursting forces caused by each of the sequentially
post-tensioned tendon combinations, as well as that of the
entire group of tendons, should be taken into account.
18.13.5.5 — For anchorage devices located away R18.13.5.5 — Where anchorages are located away from
from the end of the member, bonded reinforcement the end of a member, local tensile stresses are generated
shall be provided to transfer at least 0.35Ppu into the behind these anchorages (see Fig. R18.13.1(b)) due to
concrete section behind the anchor. Such reinforcement compatibility requirements for deformations ahead of and
shall be placed symmetrically around the anchorage behind the anchorages. Bonded tie-back reinforcement is
devices and shall be fully developed both behind and required in the immediate vicinity of the anchorage to limit
ahead of the anchorage devices. the extent of cracking behind the anchorage. The requirement
of 0.35Ppu was developed using 25 percent of the unfactored
prestressing force being resisted by reinforcement at 0.6fy.
CODE COMMENTARY
minimum reinforcement with a nominal tensile strength
equal to 2 percent of each factored prestressing force
shall be provided in orthogonal directions parallel to
the back face of all anchorage zones to limit spalling.
18.14 — Design of anchorage zones for R18.14 — Design of anchorage zones for
monostrand or single 16 mm monostrand or single 16 mm
diameter bar tendons diameter bar tendons
18.14.2 — General-zone design for slab tendons R18.14.2 — General-zone design for slab tendons
18.14.2.1 — For anchorage devices for 12.7 mm or For monostrand slab tendons, the general-zone minimum
smaller diameter strands in normalweight concrete reinforcement requirements are based on the recommenda-
18 slabs, minimum reinforcement meeting the require- tions of Joint ACI-ASCE Committee 423,18.11 which shows
ments of 18.14.2.2 and 18.14.2.3 shall be provided typical details. The horizontal bars parallel to the edge
unless a detailed analysis satisfying 18.13.5 shows required by 18.14.2.2 should be continuous where possible.
such reinforcement is not required.
The tests on which the recommendations of Reference 18.28
18.14.2.2 — Two horizontal bars at least No. 13 in were based were limited to anchorage devices for 13 mm
size shall be provided parallel to the slab edge. They diameter, 1860 MPa strand, unbonded tendons in normal-
shall be permitted to be in contact with the front face of weight concrete. Thus, for larger strand anchorage devices
the anchorage device and shall be within a distance of and for all use in lightweight concrete slabs, Committee 423
1/2h ahead of each device. Those bars shall extend at recommended that the amount and spacing of reinforcement
least 150 mm either side of the outer edges of each should be conservatively adjusted to provide for the larger
device. anchorage force and smaller splitting tensile strength of
lightweight concrete.18.11
18.14.2.3 — If the center-to-center spacing of
anchorage devices is 300 mm or less, the anchorage Both References 18.11 and 18.28 recommend that hairpin
devices shall be considered as a group. For each bars also be furnished for anchorages located within 300 mm
group of six or more anchorage devices, n + 1 hairpin of slab corners to resist edge tension forces. The words “ahead
bars or closed stirrups at least No. 10 in size shall be of” in 18.14.2.3 have the meaning shown in Fig. R18.13.1.
provided, where n is the number of anchorage
devices. One hairpin bar or stirrup shall be placed In those cases where multistrand anchorage devices are used
between each anchorage device and one on each side for slab tendons, 18.15 is applicable.
of the group. The hairpin bars or stirrups shall be
CODE COMMENTARY
placed with the legs extending into the slab perpen- The bursting reinforcement perpendicular to the plane of the
dicular to the edge. The center portion of the hairpin slab required by 18.14.2.3 for groups of relatively closely
bars or stirrups shall be placed perpendicular to the spaced tendons should also be provided in the case of
plane of the slab from 3h/8 to h/2 ahead of the widely spaced tendons if an anchorage device failure could
anchorage devices. cause more than local damage.
18.14.3 — General-zone design for groups of R18.14.3 — General-zone design for groups of
monostrand tendons in beams and girders monostrand tendons in beams and girders
Design of general zones for groups of monostrand Groups of monostrand tendons with individual monostrand
tendons in beams and girders shall meet the require- anchorage devices are often used in beams and girders.
ments of 18.13.3 through 18.13.5. Anchorage devices can be treated as closely spaced if their
center-to-center spacing does not exceed 1.5 times the width
of the anchorage device in the direction considered. If a
beam or girder has a single anchorage device or a single
group of closely spaced anchorage devices, the use of
simplified equations such as those given in R18.13.5 is
allowed, unless 18.13.5.2 governs. More complex conditions
can be designed using strut-and-tie models. Detailed
recommendations for use of such models are given in
References 18.26 and 18.29 as well as in R18.13.5.
18.15 — Design of anchorage zones for R18.15 — Design of anchorage zones for
multistrand tendons multistrand tendons
18.15.2 — Use of special anchorage devices R18.15.2 — Use of special anchorage devices
Where special anchorage devices are to be used, Skin reinforcement is reinforcement placed near the outer faces
supplemental skin reinforcement shall be furnished in in the anchorage zone to limit local crack width and spacing.
the corresponding regions of the anchorage zone, in Reinforcement in the general zone for other actions (flexure,
addition to the confining reinforcement specified for the shear, shrinkage, temperature, and similar) may be used in
anchorage device. This supplemental reinforcement satisfying the supplementary skin reinforcement requirement.
shall be similar in configuration and at least equivalent Determination of the supplementary skin reinforcement
in volumetric ratio to any supplementary skin reinforce- depends on the anchorage device hardware used and frequently
ment used in the qualifying acceptance tests of the cannot be determined until the shop-drawing stage.
anchorage device.
CODE COMMENTARY
18.15.3 — General-zone design
18.16.1 — Unbonded prestressing steel shall be encased R18.16.1 — Suitable material for corrosion protection of
with sheathing. The prestressing steel shall be completely unbonded prestressting steel should have the properties
coated and the sheathing around the prestressing steel identified in Section 5.1 of Reference 18.29.
filled with suitable material to inhibit corrosion.
18.16.2 — Sheathing shall be watertight and contin- R18.16.2 — Typically, sheathing is a continuous, seamless,
uous over entire length to be unbonded. high-density polythylene material that is extruded directly
onto the coated prestressing steel.
18.17.4 — Ducts shall be maintained free of ponded R18.17.4 — Water in ducts may cause distress to the
water if members to be grouted are exposed to surrounding concrete upon freezing. When strands are
temperatures below freezing prior to grouting. present, ponded water in ducts should also be avoided. A
corrosion inhibitor should be used to provide temporary
corrosion protection if prestressing steel is exposed to
prolonged periods of moisture in the ducts before
grouting.18.30
18.18 — Grout for bonded tendons R18.18 — Grout for bonded tendons
18.18.1 — Grout shall consist of portland cement and Proper grout and grouting procedures are critical to post-
water; or portland cement, sand, and water. tensioned construction.18.31,18.32 Grout provides bond
between the prestressing steel and the duct, and provides
corrosion protection to the prestressing steel.
CODE COMMENTARY
Past success with grout for bonded tendons has been with
portland cement. A blanket endorsement of all cementitious
materials (defined in 2.1) for use with this grout is deemed
inappropriate because of a lack of experience or tests with
cementitious materials other than portland cement and a
concern that some cementitious materials might introduce
chemicals listed as harmful to tendons in R18.18.2. Thus,
portland cement in 18.18.1 and water-cement ratio in
18.18.3.3 are retained in the Code.
18.18.2 — Materials for grout shall conform to R18.18.2 — The limitations on admixtures in 3.6 apply to
18.18.2.1 through 18.18.2.4. grout. Substances known to be harmful to tendons, grout, or
concrete are chlorides, fluorides, sulfites, and nitrates.
18.18.2.1 — Portland cement shall conform to 3.2. Aluminum powder or other expansive admixtures, when
approved, should produce an unconfined expansion of 5 to
18.18.2.2 — Water shall conform to 3.4. 10 percent. Neat cement grout is used in almost all building
construction. Use of finely graded sand in the grout should
18.18.2.3 — Sand, if used, shall conform to ASTM only be considered with large ducts having large void areas.
C144 except that gradation shall be permitted to be
modified as necessary to obtain satisfactory workability.
18.18.3.1 — Proportions of materials for grout shall Grout proportioned in accordance with these provisions will
be based on either (a) or (b): generally lead to 7-day compressive strength on standard
50 mm cubes in excess of 17 MPa and 28-day strengths of
(a) Results of tests on fresh and hardened grout about 28 MPa. The handling and placing properties of grout
prior to beginning grouting operations; or are usually given more consideration than strength when
designing grout mixtures. 18
(b) Prior documented experience with similar
materials and equipment and under comparable field
conditions.
18.18.4 — Mixing and pumping grout R18.18.4 — Mixing and pumping grout
18.18.4.1 — Grout shall be mixed in equipment In an ambient temperature of 2 °C, grout with an initial
capable of continuous mechanical mixing and agitation minimum temperature of 16 °C may require as much as 5 days
that will produce uniform distribution of materials, to reach 5.5 MPa. A minimum grout temperature of 16 °C is
passed through screens, and pumped in a manner suggested because it is consistent with the recommended
that will completely fill the ducts. minimum temperature for concrete placed at an ambient
CODE COMMENTARY
18.18.4.2 — Temperature of members at time of temperature of 2 °C. Quickset grouts, when approved, may
grouting shall be above 2 °C and shall be maintained require shorter periods of protection, and the recommenda-
above 2 °C until field-cured 50 mm cubes of grout tions of the suppliers should be followed. Test cubes should
reach a minimum compressive strength of 5.5 MPa. be cured under temperature and moisture conditions as close
as possible to those of the grout in the member. Grout temper-
18.18.4.3 — Grout temperatures shall not be above atures in excess of 32 °C will lead to difficulties in pumping.
32 °C during mixing and pumping.
18.20.1 — Prestressing force shall be determined by R18.20.1 — Elongation measurements for prestressed
both of (a) and (b): elements should be in accordance with the procedures
outlined in the Manual for Quality Control for Plants and
(a) Measurement of steel elongation. Required elon- Production Structural Precast Concrete Products, published
gation shall be determined from average load-elon- by the Precast/Prestressed Concrete Institute.18.33
gation curves for the prestressing steel used;
Section 18.18.1 of the 1989 Code was revised to permit
(b) Observation of jacking force on a calibrated gage 7 percent tolerance in prestressing steel force determined by
or load cell or by use of a calibrated dynamometer. gauge pressure and elongation measurements for post-
tensioned construction. Elongation measurements for post-
Cause of any difference in force determination tensioned construction are affected by several factors that
between (a) and (b) that exceeds 5 percent for preten- are less significant, or that do not exist, for pretensioned
sioned elements or 7 percent for post-tensioned elements. The friction along prestressing steel in post-
construction shall be ascertained and corrected. tensioning applications may be affected to varying degrees
18 by placing tolerances and small irregularities in tendon
profile due to concrete placement. The friction coefficients
between the prestressing steel and the duct are also subject
to variation. The 5 percent tolerance that has appeared since
the 1963 Code was proposed by Committee 423 in 1958,18.6
and primarily reflected experience with production of
pretensioned concrete elements. Because the tendons for
pretensioned elements are usually stressed in the air with
minimal friction effects, the 5 percent tolerance for such
elements was retained.
CODE COMMENTARY
18.20.4 — Total loss of prestress due to unreplaced R18.20.4 — This provision applies to all prestressed
broken prestressing steel shall not exceed 2 percent of concrete members. For cast-in-place post-tensioned slab
total prestress. systems, a member should be that portion considered as an
element in the design, such as the joist and effective slab
width in one-way joist systems, or the column strip or
middle strip in two-way flat plate systems.
18.21.1 — Anchorages and couplers for bonded and R18.21.1 — In the 1986 interim Code, the separate provisions
unbonded tendons shall develop at least 95 percent of for strength of unbonded and bonded tendon anchorages and
the fpu when tested in an unbonded condition, without couplers presented in 18.19.1 and 18.19.2 of the 1983 Code
exceeding anticipated set. For bonded tendons, were combined into a single revised 18.19.1 covering
anchorages and couplers shall be located so that 100 anchorages and couplers for both unbonded and bonded
percent of fpu shall be developed at critical sections tendons. Since the 1989 Code, the required strength of the
after the prestressing steel is bonded in the member. tendon-anchorage or tendon-coupler assemblies for both
unbonded and bonded tendons, when tested in an unbonded
state, is based on 95 percent of the specified breaking
strength of the prestressing steel in the test. The prestressing
steel material should comply with the minimum provisions
of the applicable ASTM specifications as outlined in 3.5.5.
The specified strength of anchorages and couplers exceeds
the maximum design strength of the prestressing steel by a
substantial margin and, at the same time, recognizes the
stress-riser effects associated with most available post-
tensioning anchorages and couplers. Anchorage and coupler
strength should be attained with a minimum amount of
permanent deformation and successive set, recognizing that
some deformation and set will occur when testing to failure.
Tendon assemblies should conform to the 2 percent elongation
requirements in ACI 30118.34 and industry recommenda-
tions.18.29 Anchorages and couplers for bonded tendons that
18
develop less than 100 percent of the specified breaking
strength of the prestressing steel should be used only where
the bond transfer length between the anchorage or coupler
and critical sections equals or exceeds that required to
develop the prestressing steel strength. This bond length may
be calculated by the results of tests of bond characteristics of
untensioned prestressing strand,18.35 or by bond tests on
other prestressing steel materials, as appropriate.
18.21.3 — In unbonded construction subject to repetitive R18.21.3 — For discussion on fatigue loading, see Refer-
loads, attention shall be given to the possibility of ence 18.36.
fatigue in anchorages and couplers.
For detailed recommendations on tests for static and cyclic
loading conditions for tendons and anchorage fittings of
unbonded tendons, see Section 4.1.3 of Reference 18.11,
and Section 15.2.2 of Reference 18.34.
CODE COMMENTARY
18.21.4 — Anchorages, couplers, and end fittings shall R18.21.4 — For recommendations regarding protection see
be permanently protected against corrosion. Sections 4.2 and 4.3 of Reference 18.11, and Sections 3.4,
3.6, 5, 6, and 8.3 of Reference 18.29.
18.22.1 — Post-tensioning tendons shall be permitted External attachment of tendons is a versatile method of
to be external to any concrete section of a member. providing additional strength, or improving serviceability,
The strength and serviceability design methods of this or both, in existing structures. It is well suited to repair or
Code shall be used in evaluating the effects of external upgrade existing structures and permits a wide variety of
tendon forces on the concrete structure. tendon arrangements.
18.22.2 — External tendons shall be considered as Additional information on external post-tensioning is given
unbonded tendons when computing flexural strength in Reference 18.37.
unless provisions are made to effectively bond the
external tendons to the concrete section along its
entire length.
18.22.3 — External tendons shall be attached to the R18.22.3 — External tendons are often attached to the
concrete member in a manner that maintains the concrete member at various locations between anchorages
desired eccentricity between the tendons and the (such as midspan, quarter points, or third points) for desired
concrete centroid throughout the full range of antici- load balancing effects, for tendon alignment, or to address
pated member deflection. tendon vibration concerns. Consideration should be given to
the effects caused by the tendon profile shifting in relationship
to the concrete centroid as the member deforms under
effects of post-tensioning and applied load.
18.22.4 — External tendons and tendon anchorage R18.22.4 — Permanent corrosion protection can be
regions shall be protected against corrosion, and the achieved by a variety of methods. The corrosion protection
details of the protection method shall be indicated on provided should be suitable to the environment in which the
the drawings or in the project specifications. tendons are located. Some conditions will require that the
prestressing steel be protected by concrete cover or by
cement grout in polyethylene or metal tubing; other conditions
18 will permit the protection provided by coatings such as paint
or grease. Corrosion protection methods should meet the
fire protection requirements of the general building code,
unless the installation of external post-tensioning is to only
improve serviceability.
CODE COMMENTARY
19.1 — Scope and definitions R19.1 — Scope and definitions
19.1.1 — Provisions of Chapter 19 shall apply to thin R19.1.1 — Discussion of the application of thin shells in
shell and folded plate concrete structures, including structures such as cooling towers and circular prestressed
ribs and edge members. concrete tanks may be found in the reports of ACI
Committee 33419.4 and ACI Committee 373.19.5
19.1.3 — Thin shells — Three-dimensional spatial R19.1.3 — Common types of thin shells are domes
structures made up of one or more curved slabs or (surfaces of revolution),19.6,19.7 cylindrical shells,19.7 barrel 19
folded plates whose thicknesses are small compared vaults,19.8 conoids,19.8 elliptical paraboloids,19.8 hyperbolic
to their other dimensions. Thin shells are characterized paraboloids,19.9 and groined vaults.19.9
by their three-dimensional load-carrying behavior,
which is determined by the geometry of their forms, by
the manner in which they are supported, and by the
nature of the applied load.
19.1.4 — Folded plates — A class of shell structure R19.1.4 — Folded plates may be prismatic,19.6,19.7 nonpris-
formed by joining flat, thin slabs along their edges to matic,19.7 or faceted. The first two types consist generally of
create a three-dimensional spatial structure. planar thin slabs joined along their longitudinal edges to
form a beam-like structure spanning between supports.
Faceted folded plates are made up of triangular or polygonal
planar thin slabs joined along their edges to form three-
dimensional spatial structures.
CODE COMMENTARY
19.1.5 — Ribbed shells — Spatial structures with R19.1.5 — Ribbed shells19.8,19.9 generally have been used
material placed primarily along certain preferred rib for larger spans where the increased thickness of the curved
lines, with the area between the ribs filled with thin slab alone becomes excessive or uneconomical. Ribbed
slabs or left open. shells are also used because of the construction techniques
employed and to enhance the aesthetic impact of the
completed structure.
19.1.6 — Auxiliary members — Ribs or edge beams R19.1.6 — Most thin shell structures require ribs or edge
that serve to strengthen, stiffen, or support the shell; beams at their boundaries to carry the shell boundary forces,
usually, auxiliary members act jointly with the shell. to assist in transmitting them to the supporting structure,
and to accommodate the increased amount of reinforcement
in these areas.
19.1.7 — Elastic analysis — An analysis of deforma- R19.1.7 — Elastic analysis of thin shells and folded plates
tions and internal forces based on equilibrium, can be performed using any method of structural analysis
compatibility of strains, and assumed elastic behavior, based on assumptions that provide suitable approximations
and representing to a suitable approximation the to the three-dimensional behavior of the structure. The
three-dimensional action of the shell together with its method should determine the internal forces and displace-
auxiliary members. ments needed in the design of the shell proper, the rib or
edge members, and the supporting structure. Equilibrium of
internal forces and external loads and compatibility of
deformations should be satisfied.
19.1.8 — Inelastic analysis — An analysis of deforma- R19.1.8 — Inelastic analysis of thin shells and folded plates
tions and internal forces based on equilibrium, can be performed using a refined method of analysis based
nonlinear stress-strain relations for concrete and on the specific nonlinear material properties, nonlinear
reinforcement, consideration of cracking and time- behavior due to the cracking of concrete, and time-depen-
dependent effects, and compatibility of strains. The dent effects such as creep, shrinkage, temperature, and load
analysis shall represent to a suitable approximation history. These effects are incorporated in order to trace the
three-dimensional action of the shell together with its response and crack propagation of a reinforced concrete
auxiliary members. shell through the elastic, inelastic, and ultimate ranges. Such
analyses usually require incremental loading and iterative
procedures to converge on solutions that satisfy both
equilibrium and strain compatibility. 19.12,19.13
CODE COMMENTARY
19.2 — Analysis and design R19.2 — Analysis and design
19.2.1 — Elastic behavior shall be an accepted basis R19.2.1 — For types of shell structures where experience,
for determining internal forces and displacements of tests, and analyses have shown that the structure can sustain
thin shells. This behavior shall be permitted to be reasonable overloads without undergoing brittle failure,
established by computations based on an analysis of elastic analysis is an acceptable procedure. In such cases, it
the uncracked concrete structure in which the material may be assumed that reinforced concrete is ideally elastic,
is assumed linearly elastic, homogeneous, and homogeneous, and isotropic, having identical properties in
isotropic. Poisson’s ratio of concrete shall be permitted all directions. An analysis should be performed for the shell
to be taken equal to zero. considering service load conditions. The analysis of shells
of unusual size, shape, or complexity should consider
behavior through the elastic, cracking, and inelastic stages.
19.2.2 — Inelastic analyses shall be permitted to be R19.2.2 — Several inelastic analysis procedures contain
used where it can be shown that such methods possible solution methods.19.12,19.13
provide a safe basis for design.
19.2.4 — Experimental or numerical analysis procedures R19.2.4 — Experimental analysis of elastic models19.14 has
shall be permitted where it can be shown that such been used as a substitute for an analytical solution of a
procedures provide a safe basis for design. complex shell structure. Experimental analysis of reinforced
microconcrete models through the elastic, cracking,
inelastic, and ultimate stages should be considered for
important shells of unusual size, shape, or complexity.
19.2.5 — Approximate methods of analysis shall be R19.2.5 — Solutions that include both membrane and bending
permitted where it can be shown that such methods effects and satisfy conditions of compatibility and equilibrium
provide a safe basis for design. are encouraged. Approximate solutions that satisfy statics but
not the compatibility of strains may be used only when extensive
experience has proved that safe designs have resulted from their
use. Such methods include beam-type analysis for barrel shells
and folded plates having large ratios of span to either width or
radius of curvature, simple membrane analysis for shells of
revolution, and others in which the equations of equilibrium
are satisfied, while the strain compatibility equations are not.
19.2.6 — In prestressed shells, the analysis shall also R19.2.6 — If the shell is prestressed, the analysis should
consider behavior under loads induced during include its strength at factored loads as well as its adequacy
prestressing, at cracking load, and at factored load. under service loads, under the load that causes cracking, and
Where tendons are draped within a shell, design shall under loads induced during prestressing. Axial forces due to
take into account force components on the shell draped tendons may not lie in one plane, and due consider-
resulting from the tendon profile not lying in one plane. ation should be given to the resulting force components. The
effects of post-tensioning of shell-supporting members
should be taken into account.
CODE COMMENTARY
19.2.7 — The thickness of a shell and its reinforce- R19.2.7 — The thin shell’s thickness and reinforcement are
ment shall be proportioned for the required strength required to be proportioned to satisfy the strength provisions
and serviceability, using either the strength design of this Code, and to resist internal forces obtained from an
method of 8.1.1 or the design method of 8.1.2. analysis, an experimental model study, or a combination
thereof. Reinforcement sufficient to minimize cracking
under service load conditions should be provided. The
thickness of the shell is often dictated by the required
reinforcement and the construction constraints, by 19.2.8,
or by the Code minimum thickness requirements.
19.2.8 — Shell instability shall be investigated and R19.2.8 — Thin shells, like other structures that experience in-
shown by design to be precluded. plane membrane compressive forces, are subject to buckling
when the applied load reaches a critical value. Because of the
surface-like geometry of shells, the problem of calculating
buckling load is complex. If one of the principal membrane
forces is tensile, the shell is less likely to buckle than if both
principal membrane forces are compressive. The kinds of
membrane forces that develop in a shell depend on its initial
shape and the manner in which the shell is supported and
loaded. In some types of shells, post-buckling behavior should
be considered in determining safety against instability.19.2
19.2.10 — Strength design of shell slabs for R19.2.10 — The stresses and strains in the shell slab used
membrane and bending forces shall be based on the for design are those determined by analysis (elastic or
distribution of stresses and strains as determined from inelastic) multiplied by appropriate load factors. Because of
either an elastic or an inelastic analysis. detrimental effects of membrane cracking, the computed
tensile strain in the reinforcement under factored loads
should be limited.
CODE COMMENTARY
19.2.11 — In a region where membrane cracking is R19.2.11 — When principal tensile stress produces
predicted, the nominal compressive strength parallel membrane cracking in the shell, experiments indicate the
to the cracks shall be taken as 0.4fc′ . attainable compressive strength in the direction parallel to
the cracks is reduced.19.16,19.17
19.4.1 — Shell reinforcement shall be provided to R19.4.1 — At any point in a shell, two different kinds of
resist tensile stresses from internal membrane forces, internal forces may occur simultaneously: those associated
to resist tension from bending and twisting moments, with membrane action, and those associated with bending of
to limit shrinkage and temperature crack width and the shell. The membrane forces are assumed to act in the
spacing, and as reinforcement at shell boundaries, tangential plane midway between the surfaces of the shell,
load attachments, and shell openings. and are the two axial forces and the membrane shears. Flexural
effects include bending moments, twisting moments, and
the associated transverse shears. Limiting membrane crack
width and spacing due to shrinkage, temperature, and
service load conditions is a major design consideration.
19.4.2 — Tensile reinforcement shall be provided in R19.4.2 — The requirement of ensuring strength in all
two or more directions and shall be proportioned such directions is based on safety considerations. Any method
that its resistance in any direction equals or exceeds that ensures sufficient strength consistent with equilibrium
the component of internal forces in that direction. is acceptable. The direction of the principal membrane
tensile force at any point may vary depending on the direction,
Alternatively, reinforcement for the membrane forces in magnitudes, and combinations of the various applied loads.
the slab shall be calculated as the reinforcement
required to resist axial tensile forces plus the tensile The magnitude of the internal membrane forces, acting at
force due to shear-friction required to transfer shear any point due to a specific load, is generally calculated on
the basis of an elastic theory in which the shell is assumed 19
across any cross section of the membrane. The
assumed coefficient of friction, μ, shall not exceed that as uncracked. The computation of the required amount of
specified in 11.6.4.3. reinforcement to resist the internal membrane forces has
been traditionally based on the assumption that concrete
does not resist tension. The associated deflections, and the
possibility of cracking, should be investigated in the
serviceability phase of the design. Achieving this may
require a working stress design for steel selection.
CODE COMMENTARY
that shear integrity of a shell should be maintained at
factored loads. It is not necessary to calculate principal
stresses if the alternative approach is used.
19.4.3 — The area of shell reinforcement at any R19.4.3 — Minimum membrane reinforcement corresponding
section as measured in two orthogonal directions shall to slab shrinkage and temperature reinforcement are to be
not be less than the slab shrinkage or temperature provided in at least two approximately orthogonal directions
reinforcement required by 7.12. even if the calculated membrane forces are compressive in
one or more directions.
19.4.5 — The area of shell tension reinforcement shall R19.4.5 — The requirement that the tensile reinforcement
be limited so that the reinforcement will yield before yields before the concrete crushes anywhere is consistent
either crushing of concrete in compression or shell with 10.3.3. Such crushing can also occur in regions near
buckling can take place. supports and, for some shells, where the principal membrane
forces are approximately equal and opposite in sign.
19.4.6 — In regions of high tension, membrane R19.4.6 — Generally, for all shells, and particularly in
reinforcement shall, if practical, be placed in the regions of substantial tension, the orientation of reinforcement
general directions of the principal tensile membrane should approximate the directions of the principal tensile
forces. Where this is not practical, it shall be permitted membrane forces. However, in some structures it is not
to place membrane reinforcement in two or more possible to detail the reinforcement to follow the stress
component directions. trajectories. For such cases, orthogonal component reinforce-
ment is allowed.
19.4.7 — If the direction of reinforcement varies more R19.4.7 — When the directions of reinforcement deviate
than 10 degrees from the direction of principal tensile significantly (more than 10 degrees) from the directions of
membrane force, the amount of reinforcement shall be the principal membrane forces, higher strains in the shell
reviewed in relation to cracking at service loads. occur to develop the reinforcement. This might lead to the
development of unacceptable wide cracks. The crack width
should be estimated and limited if necessary.
19
Permissible crack widths for service loads under different
environmental conditions are given in a report of ACI
Committee 224.19.20 Crack width can be limited by an
increase in the amount of reinforcement used, by reducing
the stress at the service load level, by providing reinforcement
in three or more directions in the plane of the shell, or by
using closer spacing of smaller-diameter bars.
19.4.8 — Where the magnitude of the principal tensile R19.4.8 — The practice of concentrating tensile reinforcement
membrane stress within the shell varies greatly over in the regions of maximum tensile stress has led to a number
the area of the shell surface, reinforcement resisting of successful and economical designs, primarily for long
the total tension shall be permitted to be concentrated folded plates, long barrel vault shells, and for domes. The
in the regions of largest tensile stress where it can be requirement of providing the minimum reinforcement in the
shown that this provides a safe basis for design. remaining tensile zone is intended to limit crack width and
However, the ratio of shell reinforcement in any portion spacing.
of the tensile zone shall be not less than 0.0035 based
on the overall thickness of the shell.
CODE COMMENTARY
19.4.9 — Reinforcement required to resist shell R19.4.9 — The design method should ensure that the
bending moments shall be proportioned with due concrete sections, including consideration of the reinforcement,
regard to the simultaneous action of membrane axial are capable of developing the internal forces required by the
forces at the same location. Where shell reinforcement equations of equilibrium.19.21 The sign of bending moments
is required in only one face to resist bending moments, may change rapidly from point to point of a shell. For this
equal amounts shall be placed near both surfaces of reason, reinforcement to resist bending, where required, is
the shell even though a reversal of bending moments to be placed near both outer surfaces of the shell. In many
is not indicated by the analysis. cases, the thickness required to provide proper cover and
spacing for the multiple layers of reinforcement may govern
the design of the shell thickness.
19.4.10 — Shell reinforcement in any direction shall R19.4.10 — The value of φ to be used is that prescribed in
not be spaced farther apart than 450 mm nor farther 9.3.2.1 for axial tension.
apart than five times the shell thickness. Where the
principal membrane tensile stress on the gross
concrete area due to factored loads exceeds
0.33φλ f c′ , reinforcement shall not be spaced farther
apart than three times the shell thickness.
19.4.11 — Shell reinforcement at the junction of the R19.4.11 and R19.4.12 — On curved shell surfaces it is
shell and supporting members or edge members shall difficult to control the alignment of precut reinforcement.
be anchored in or extended through such members in This should be considered to avoid insufficient splice and
accordance with the requirements of Chapter 12, development lengths. Sections 19.4.11 and 19.4.12 require
except that the minimum development length shall be extra reinforcement length to maintain the minimum lengths
1.2ld but not less than 450 mm. on curved surfaces.
19.5.1 — When removal of formwork is based on a R19.5.1 — When early removal of forms is necessary, the
specific modulus of elasticity of concrete because of magnitude of the modulus of elasticity at the time of
stability or deflection considerations, the value of the proposed form removal should be investigated to ensure
modulus of elasticity, Ec , used shall be determined safety of the shell with respect to buckling, and to restrict
from flexural tests of field-cured beam specimens. The deflections.19.3,19.22 The value of the modulus of elasticity
number of test specimens, the dimensions of test Ec should be obtained from a flexural test of field-cured
beam specimens, and test procedures shall be specified specimens. It is not sufficient to determine the modulus
by the licensed design professional. from the formula in 8.5.1, even if the compressive strength
of concrete is determined for the field-cured specimen.
19.5.2 — Contract documents shall specify the R19.5.2 — In some types of shells, small local deviations from
tolerances for the shape of the shell. If construction the theoretical geometry of the shell can cause relatively large
results in deviations from the shape greater than the changes in local stresses and in overall safety against instability.
specified tolerances, an analysis of the effect of the These changes can result in local cracking and yielding that may
deviations shall be made and any required remedial make the structure unsafe or can greatly affect the critical load,
actions shall be taken to ensure safe behavior. producing instability. The effect of such deviations should be
evaluated and any necessary remedial actions should be taken.
Attention is needed when using air-supported form systems.19.23
19
20.1.1 — If there is doubt that a part or all of a structure Chapter 20 does not cover load testing for the approval of
meets the safety requirements of this Code, a strength new design or construction methods. (See 16.10 for recom-
evaluation shall be carried out as required by the mendations on strength evaluation of precast concrete
licensed design professional or building official. members.) Provisions of Chapter 20 may be used to evaluate
whether a structure or a portion of a structure satisfies the
safety requirements of this Code. A strength evaluation may
be required if the materials are considered to be deficient in
quality, if there is evidence indicating faulty construction, if
a structure has deteriorated, if a building will be used for a
new function, or if, for any reason, a structure or a portion
of it does not appear to satisfy the requirements of the Code.
In such cases, Chapter 20 provides guidance for investigating
the safety of the structure.
20.1.2 — If the effect of the strength deficiency is well R20.1.2 — Strength considerations related to axial load,
understood and if it is feasible to measure the flexure, and combined axial load and flexure are well under-
dimensions and material properties required for analysis, stood. There are reliable theories relating strength and short-
analytical evaluations of strength based on those term displacement to load in terms of dimensional and
measurements shall suffice. Required data shall be material data for the structure.
determined in accordance with 20.2.
To determine the strength of the structure by analysis, calcu- 20
lations should be based on data gathered on the actual
dimensions of the structure, properties of the materials in
place, and all pertinent details. Requirements for data
collection are in 20.2.
20.1.3 — If the effect of the strength deficiency is not R20.1.3 — If the shear or bond strength of an element is
well understood or if it is not feasible to establish the critical in relation to the doubt expressed about safety, a test
required dimensions and material properties by may be the most efficient solution to eliminate or confirm
measurement, a load test shall be required if the the doubt. A test may also be appropriate if it is not feasible
structure is to remain in service. to determine the material and dimensional properties
required for analysis, even if the cause of the concern relates
to flexure or axial load.
CODE COMMENTARY
20.1.4 — If the doubt about safety of a part or all of a R20.1.4 — For a deteriorating structure, the acceptance
structure involves deterioration, and if the observed provided by the load test may not be assumed to be without
response during the load test satisfies the acceptance limits in terms of time. In such cases, a periodic inspection
criteria, the structure or part of the structure shall be program is useful. A program that involves physical tests
permitted to remain in service for a specified time and periodic inspection can justify a longer period in
period. If deemed necessary by the licensed design service. Another option for maintaining the structure in
professional, periodic reevaluations shall be conducted. service, while the periodic inspection program continues, is
to limit the live load to a level determined to be appropriate.
20.2.1 — Dimensions of the structural elements shall R20.2.1 — Critical sections are where each type of stress
be established at critical sections. calculated for the load in question reaches its maximum value.
20.2.2 — Locations and sizes of the reinforcing bars, R20.2.2 — For individual elements, amount, size, arrangement,
welded wire reinforcement, or tendons shall be deter- and location should be determined at the critical sections for
mined by measurement. It shall be permitted to base reinforcement or tendons, or both, designed to resist applied
reinforcement locations on available drawings if spot load. Nondestructive investigation methods are acceptable. In
checks are made confirming the information on the large structures, determination of these data for approximately
drawings. 5 percent of the reinforcement or tendons in critical regions
may suffice if these measurements confirm the data
20
provided in the construction drawings.
20.2.3 — If required, concrete strength shall be based R20.2.3 — ACI Committee 214 has developed two methods
on results of cylinder tests from the original construc- for determining fc′ from cores taken from an existing structure.
tion or tests of cores removed from the part of the These methods are described in ACI 214.4R20.1 and rely on
structure where the strength is in question. For statistical analysis techniques. The procedures described are
strength evaluation of an existing structure, cylinder or only appropriate where the determination of an equivalent
core test data shall be used to estimate an equivalent fc′ is necessary for the strength evaluation of an existing
fc′ . The method for obtaining and testing cores shall structure and should not be used to investigate low cylinder
be in accordance with ASTM C42M. strength test results in new construction, which is considered
in 5.6.5.
CODE COMMENTARY
20.2.4 — If required, reinforcement or prestressing steel R20.2.4 — The number of tests required depends on the
strength shall be based on tensile tests of representative uniformity of the material and is best determined by the
samples of the material in the structure in question. licensed design profession responsible for the evaluation.
20.2.5 — If the required dimensions and material R20.2.5 — Strength reduction factors given in 20.2.5 are
properties are determined through measurements and larger than those specified in Chapter 9. These increased
testing, and if calculations can be made in accordance values are justified by the use of accurate field-obtained
with 20.1.2, it shall be permitted to increase φ from material properties, actual in-place dimensions, and well-
those specified in 9.3, but φ shall not be more than: understood methods of analysis.
Tension-controlled sections, The strength reduction factors in 20.2.5 were changed for
as defined in 10.3.4.............................................. 1.0 the 2002 edition to be compatible with the load combinations
and strength reduction factors of Chapter 9, which were
Compression-controlled sections, revised at that time. For the 2008 edition, the strength reduction
as defined in 10.3.3: factor in 20.2.5 for members with spiral reinforcement was
Members with spiral reinforcement increased to correspond to an increase in this strength
conforming to 10.9.3.......................................... 0.9 reduction factor in Chapter 9.
The number and arrangement of spans or panels It is important to apply the load at locations so that its
loaded shall be selected to maximize the deflection and effects on the suspected defect are a maximum and the prob-
stresses in the critical regions of the structural elements ability of unloaded members sharing the applied load is a
of which strength is in doubt. More than one test load minimum. In cases where it is shown by analysis that
arrangement shall be used if a single arrangement will adjoining unloaded elements will help carry some of the
not simultaneously result in maximum values of the load, the load should be placed to develop effects consistent
effects (such as deflection, rotation, or stress) necessary with the intent of the load factor.
to demonstrate the adequacy of the structure.
CODE COMMENTARY
20.3.3 — A load test shall not be made until that
portion of the structure to be subjected to load is at
least 56 days old. If the owner of the structure, the
contractor, and all involved parties agree, it shall be
permitted to make the test at an earlier age.
20.4.2 — Test load shall be applied in not less than R20.4.2 — Inspecting the structure after each load increment
four approximately equal increments. is advisable.
20.4.3 — Uniform test load shall be applied in a manner R20.4.3 — Arching refers to the tendency for the load to be
to ensure uniform distribution of the load transmitted to transmitted nonuniformly to the flexural element being
the structure or portion of the structure being tested. tested. For example, if a slab is loaded by a uniform
Arching of the applied load shall be avoided. arrangement of bricks with the bricks in contact, arching
would results in reduction of the load on the slab near the
midspan of the slab.
20.5.1 — The portion of the structure tested shall R20.5.1 — A general acceptance criterion for the behavior of
show no evidence of failure. Spalling and crushing of a structure under the test load is that it does not show
compressed concrete shall be considered an indication evidence of failure. Evidence of failure includes cracking,
of failure. spalling, or deflection of such magnitude and extent that the
observed result is obviously excessive and incompatible with
the safety requirements of the structure. No simple rules have
been developed for application to all types of structures and
conditions. If sufficient damage has occurred so that the
structure is considered to have failed that test, retesting is not
permitted because it is considered that damaged members
should not be put into service even at a lower load rating.
CODE COMMENTARY
of the state of the structure and should be observed to help
determine whether the structure is satisfactory. However,
exact prediction or measurement of crack widths in reinforced
concrete elements is not likely to be achieved under field
conditions. Establish criteria before the test, relative to the
types of cracks anticipated; where the cracks will be
measured; how they will be measured; and approximate
limits or criteria to evaluate new cracks or limits for the
changes in crack width.
20.5.2 — Measured deflections shall satisfy either R20.5.2 — The deflection limits and the retest option
Eq. (20-1) or (20-2): follow past practice. If the structure shows no evidence of
failure, recovery of deflection after removal of the test load
2 is used to determine whether the strength of the structure is
lt
Δ 1 ≤ ----------------------- (20-1) satisfactory. In the case of a very stiff structure, however, the
20, 000h errors in measurements under field conditions may be of the
same order as the actual deflections and recovery. To avoid
Δ penalizing a satisfactory structure in such a case, recovery
Δ r ≤ -----1- (20-2) measurements are waived if the maximum deflection is less
4
than lt2/(20,000h). The residual deflection Δr is the differ-
If the measured maximum and residual deflections, Δ1 ence between the initial and final (after load removal)
and Δr , do not satisfy Eq. (20-1) or (20-2), it shall be deflections for the load test or the repeat load test.
permitted to repeat the load test.
Δ
Δ r ≤ -----2- (20-3)
5
20.5.4 — In regions of structural members without R20.5.4 — The intent of 20.5.4 is to make the professionals
transverse reinforcement, appearance of structural in charge of the test pay attention to the structural implication
cracks inclined to the longitudinal axis and having a of observed inclined cracks that may lead to brittle collapse
horizontal projection longer than the depth of the in members without transverse reinforcement.
member at midpoint of the crack shall be evaluated.
CODE COMMENTARY
20.5.5 — In regions of anchorage and lap splices, the R20.5.5 — Cracking along the axis of the reinforcement in
appearance along the line of reinforcement of a series anchorage zones may be related to high stresses associated
of short inclined cracks or horizontal cracks shall be with the transfer of forces between the reinforcement and
evaluated. the concrete. These cracks may be indicators of pending
brittle failure of the element if they are associated with the
main reinforcement. It is important that their causes and
consequences be evaluated.
20.6 — Provision for lower load rating R20.6 — Provision for lower load rating
If the structure under investigation does not satisfy Except for load tested members that have failed under a test
conditions or criteria of 20.1.2, 20.5.2, or 20.5.3, the (see 20.5), the building official may permit the use of a
structure shall be permitted for use at a lower load structure or member at a lower load rating that is judged to
rating based on the results of the load test or analysis, be safe and appropriate on the basis of the test results.
if approved by the building official.
20.7 — Safety
20
21.1.1.1 — Chapter 21 contains requirements for Chapter 21 contains provisions considered to be the
design and construction of reinforced concrete minimum requirements for a cast-in-place or precast
members of a structure for which the design forces, concrete structure capable of sustaining a series of oscillations
related to earthquake motions, have been determined into the inelastic range of response without critical deteriora-
on the basis of energy dissipation in the nonlinear tion in strength. The integrity of the structure in the inelastic
range of response. range of response should be maintained because the design
earthquake forces defined in documents such as ASCE/
21.1.1.2 — All structures shall be assigned to a SEI 7,21.1 the IBC,21.2 the UBC,21.3 and the NEHRP21.4
seismic design category (SDC) in accordance with provisions are considered less than those corresponding to
1.1.9.1. linear response at the anticipated earthquake intensity.21.4-21.7
21.1.1.3 — All members shall satisfy requirements As a properly detailed cast-in-place or precast concrete
of Chapters 1 to 19 and 22. Structures assigned to structure responds to strong ground motion, its effective
SDC B, C, D, E, or F also shall satisfy 21.1.1.4 through stiffness decreases and its energy dissipation increases.
21.1.1.8, as applicable. These changes tend to reduce the response accelerations and
lateral inertia forces relative to values that would occur were
21.1.1.4 — Structures assigned to SDC B shall the structure to remain linearly elastic and lightly
satisfy 21.1.2. damped.21.7 Thus, the use of design forces representing
earthquake effects such as those in ASCE/SEI 7 requires
21.1.1.5 — Structures assigned to SDC C shall that the seismic-force-resisting system retain a substantial
satisfy 21.1.2 and 21.1.8. portion of its strength into the inelastic range under
displacement reversals.
21.1.1.6 — Structures assigned to SDC D, E, or F
shall satisfy 21.1.2 through 21.1.8, and 21.11 through The provisions of Chapter 21 relate detailing requirements
21.13. to type of structural framing and seismic design category
(SDC). SDCs are adopted directly from ASCE/SEI 7, and
21.1.1.7 — Structural systems designated as part of relate to considerations of seismic hazard level, soil type,
the seismic-force-resisting system shall be restricted occupancy, and use. Before the 2008 Code, low, intermediate,
to those designated by the legally adopted general and high seismic risk designations were used to delineate
building code of which this Code forms a part, or detailing requirements. For a qualitative comparison of
determined by other authority having jurisdiction in SDCs and seismic risk designations, see Table R1.1.9.1.
areas without a legally adopted building code. Except The assignment of a structure to a SDC is regulated by the 21
for SDC A, for which Chapter 21 does not apply, the legally adopted general building code of which this Code
following provisions shall be satisfied for each structural forms a part (see 1.1.9).
system designated as part of the seismic-force-
resisting system, regardless of the SDC: The design and detailing requirements should be compatible
with the level of energy dissipation (or toughness) assumed
(a) Ordinary moment frames shall satisfy 21.2. in the computation of the design earthquake forces. The
terms “ordinary,” “intermediate,” and “special” are specifically
(b) Ordinary reinforced concrete structural walls used to facilitate this compatibility. The degree of required
need not satisfy any provisions in Chapter 21. toughness and, therefore, the level of required detailing,
(c) Intermediate moment frames shall satisfy 21.3. increases for structures progressing from ordinary through
intermediate to special categories. It is essential that structures
(d) Intermediate precast walls shall satisfy 21.4. assigned to higher SDCs possess a higher degree of toughness.
It is permitted, however, to design for higher toughness in
(e) Special moment frames shall satisfy 21.5 the lower SDCs and take advantage of the lower design
through 21.8. force levels.
(f) Special structural walls shall satisfy 21.9.
ACI 318 Building Code and Commentary
324 CHAPTER 21
CODE COMMENTARY
(g) Special structural walls constructed using The provisions of Chapters 1 through 19 and 22 are considered
precast concrete shall satisfy 21.10. to be adequate for structures assigned to SDC A (corresponding
to lowest seismic hazard). For structures assigned to SDC B,
All special moment frames and special structural walls additional requirements apply.
shall also satisfy 21.1.3 through 21.1.7.
Structures assigned to SDC C may be subjected to moderately
21.1.1.8 — A reinforced concrete structural system strong ground shaking. The designated seismic-force-
not satisfying the requirements of this chapter shall be resisting system typically comprises some combination of
permitted if it is demonstrated by experimental ordinary cast-in-place structural walls, intermediate precast
evidence and analysis that the proposed system will structural walls, and intermediate moment frames. The
have strength and toughness equal to or exceeding legally adopted general building code of which this Code
those provided by a comparable monolithic reinforced forms a part also may contain provisions for use of other
concrete structure satisfying this chapter. seismic-force-resisting systems in SDC C. Section 21.1.1.7
defines requirements for whatever system is selected.
CODE COMMENTARY
TABLE R21.1.1 — SECTIONS OF CHAPTER 21 TO
BE SATISFIED IN TYPICAL APPLICATIONS*
Seismic Design Category
Component resisting
earthquake effect, unless A B C D, E, F
otherwise noted (None) (21.1.1.4) (21.1.1.5) (21.1.1.6)
Analysis and design 21.1.2,
21.1.2 21.1.2
requirements 21.1.3
21.1.4 -
Materials None None
21.1.7
21.5, 21.6,
Frame members 21.2 21.3
21.7, 21.8
Structural walls and
None None 21.9
coupling beams
Precast structural walls None None 21.4 21.4,† 21.10
Structural diaphragms
and trusses None None 21.11
21.1.2 — Analysis and proportioning of structural R21.1.2 — Analysis and proportioning of structural
members members
21.1.2.1 — The interaction of all structural and It is assumed that the distribution of required strength to the
nonstructural members that affect the linear and various components of a seismic-force-resisting system will
nonlinear response of the structure to earthquake be guided by the analysis of a linearly elastic model of the
motions shall be considered in the analysis. system acted upon by the factored forces required by the
legally adopted general building code. If nonlinear response
21.1.2.2 — Rigid members assumed not to be a part history analyses are to be used, base motions should be
of the seismic-force-resisting system shall be selected after a detailed study of the site conditions and
permitted provided their effect on the response of the local seismic history.
CODE COMMENTARY
system is considered and accommodated in the struc- Because the design basis earthquake admits nonlinear
tural design. Consequences of failure of structural and response, it is necessary to investigate the stability of the
nonstructural members that are not a part of the seismic-force-resisting system as well as its interaction with
seismic-force-resisting system shall be considered. other structural and nonstructural members at displacements
larger than those indicated by linear analysis. To handle this
21.1.2.3 — Structural members extending below the without having to resort to nonlinear response analysis, one
base of structure that are required to transmit forces option is to multiply by a factor of at least two the displace-
resulting from earthquake effects to the foundation ments from linear analysis by using the factored lateral
shall comply with the requirements of Chapter 21 that forces, unless the legally adopted general building code
are consistent with the seismic-force-resisting system specifies the factors to be used as in the IBC or the UBC.
above the base of structure. For lateral displacement calculations, assuming all the
horizontal structural members to be fully cracked is likely to
lead to better estimates of the possible drift than using
uncracked stiffness for all members. The analysis
assumptions described in 8.8 also may be used to estimate
lateral deflections of reinforced concrete building systems.
21.1.4 — Concrete in special moment frames and R21.1.4 — Concrete in special moment frames and
special structural walls special structural walls
21.1.4.1 — Requirements of 21.1.4 apply to special Requirements of this section refer to concrete quality in
moment frames and special structural walls and frames and walls that resist earthquake-induced forces. The
coupling beams. maximum specified compressive strength of lightweight
concrete to be used in structural design calculations is
21.1.4.2 — Specified compressive strength of limited to 35 MPa, primarily because of paucity of experi-
concrete, fc′ , shall be not less than 21 MPa. mental and field data on the behavior of members made with
lightweight concrete subjected to displacement reversals in the
21.1.4.3 — Specified compressive strength of light- nonlinear range. If convincing evidence is developed for a
weight concrete, fc′ , shall not exceed 35 MPa unless specific application, the limit on maximum specified
demonstrated by experimental evidence that structural compressive strength of lightweight concrete may be
members made with that lightweight concrete provide increased to a level justified by the evidence.
CODE COMMENTARY
strength and toughness equal to or exceeding those of
comparable members made with normalweight
concrete of the same strength. Modification factor λ for
lightweight concrete in this Chapter shall be in accor-
dance with 8.6.1 unless specifically noted otherwise.
21.1.5 — Reinforcement in special moment frames R21.1.5 — Reinforcement in special moment frames
and special structural walls and special structural walls
21.1.5.1 — Requirements of 21.1.5 apply to special Use of longitudinal reinforcement with strength substan-
moment frames and special structural walls and tially higher than that assumed in design will lead to higher
coupling beams. shear and bond stresses at the time of development of yield
moments. These conditions may lead to brittle failures in
21.1.5.2 — Deformed reinforcement resisting earth- shear or bond and should be avoided even if such failures
quake-induced flexural and axial forces in frame may occur at higher loads than those anticipated in design.
members, structural walls, and coupling beams, shall Therefore, a ceiling is placed on the actual yield strength of
comply with ASTM A706M. ASTM A615M Grades 280 the steel [see 21.1.5.2(a)].
and 420 reinforcement shall be permitted in these
members if: The requirement for a tensile strength larger than the yield
strength of the reinforcement [21.1.5.2(b)] is based on the
(a) The actual yield strength based on mill tests assumption that the capability of a structural member to
does not exceed fy by more than 125 MPa; and develop inelastic rotation capacity is a function of the length
of the yield region along the axis of the member. In interpreting
(b) The ratio of the actual tensile strength to the experimental results, the length of the yield region has been
actual yield strength is not less than 1.25. related to the relative magnitudes of nominal and yield
21.1.5.3 — Prestressing steel resisting earthquake- moments.21.8 According to this interpretation, the larger the
induced flexural and axial loads in frame members and ratio of nominal to yield moment, the longer the yield
in precast structural walls shall comply with ASTM region. Chapter 21 requires that the ratio of actual tensile
A416M or A722M. strength to actual yield strength is not less than 1.25.
Members with reinforcement not satisfying this condition
21.1.5.4 — The value of fyt used to compute the can also develop inelastic rotation, but their behavior is
amount of confinement reinforcement shall not exceed sufficiently different to exclude them from direct consideration
700 MPa. on the basis of rules derived from experience with members
reinforced with strain-hardening steel.
21.1.5.5 — The value of fy or fyt used in design of
shear reinforcement shall conform to 11.4.2. The restrictions on the values of fy and fyt apply to all types
of transverse reinforcement, including spirals, circular
hoops, rectilinear hoops, and crossties. The restrictions on
the values of fy and fyt in 11.4.2 for computing nominal
shear strength are intended to limit the width of shear 21
cracks. Research results21.9-21.11 indicate that higher yield
strengths can be used effectively as confinement reinforce-
ment as specified in 21.6.4.4.
21.1.6 — Mechanical splices in special moment R21.1.6 — Mechanical splices in special moment
frames and special structural walls frames and special structural walls
21.1.6.1 — Mechanical splices shall be classified as In a structure undergoing inelastic deformations during an
either Type 1 or Type 2 mechanical splices, as follows: earthquake, the tensile stresses in reinforcement may
approach the tensile strength of the reinforcement. The
(a) Type 1 mechanical splices shall conform to requirements for Type 2 mechanical splices are intended to
12.14.3.2; avoid a splice failure when the reinforcement is subjected to
expected stress levels in yielding regions. Type 1 splices are
(b) Type 2 mechanical splices shall conform to not required to satisfy the more stringent requirements for
12.14.3.2 and shall develop the specified tensile Type 2 splices, and may not be capable of resisting the
strength of the spliced bar.
CODE COMMENTARY
21.1.6.2 — Type 1 mechanical splices shall not be stress levels expected in yielding regions. The locations of
used within a distance equal to twice the member Type 1 splices are restricted because tensile stresses in
depth from the column or beam face for special reinforcement in yielding regions can exceed the strength
moment frames or from sections where yielding of the requirements of 12.14.3.2.
reinforcement is likely to occur as a result of inelastic
lateral displacements. Type 2 mechanical splices shall Recommended detailing practice would preclude the use of
be permitted to be used at any location. splices in regions of potential yield in members resisting
earthquake effects. If use of mechanical splices in regions of
potential yielding cannot be avoided, there should be
documentation on the actual strength characteristics of the
bars to be spliced, on the force-deformation characteristics
of the spliced bar, and on the ability of the Type 2 splice to
be used to meet the specified performance requirements.
21.1.7 — Welded splices in special moment frames R21.1.7 — Welded splices in special moment frames
and special structural walls and special structural walls
21.1.7.2 — Welding of stirrups, ties, inserts, or other R21.1.7.2 — Welding of crossing reinforcing bars can
similar elements to longitudinal reinforcement that is lead to local embrittlement of the steel. If welding of
required by design shall not be permitted. crossing bars is used to facilitate fabrication or placement of
reinforcement, it should be done only on bars added for such
purposes. The prohibition of welding crossing reinforcing
bars does not apply to bars that are welded with welding
operations under continuous, competent control as in the
manufacture of welded wire reinforcement.
21.2.1 — Scope These provisions were introduced in the 2008 Code and
apply only to ordinary moment frames assigned to SDC B.
Requirements of 21.2 apply to ordinary moment frames The provisions for beam reinforcement are intended to
forming part of the seismic-force-resisting system. improve continuity in the framing members as compared
with the provisions of Chapters 1 through 18 and thereby
21.2.2 — Beams shall have at least two of the longitu- improve lateral force resistance and structural integrity;
dinal bars continuous along both the top and bottom these provisions do not apply to slab-column moment
faces. These bars shall be developed at the face of frames. The provisions for columns are intended to provide
support. additional toughness to resist shear for columns with
proportions that would otherwise make them more suscep-
21.2.3 — Columns having clear height less than or tible to shear failure under earthquake loading.
equal to five times the dimension c1 shall be designed
for shear in accordance with 21.3.3.
CODE COMMENTARY
21.3 — Intermediate moment frames R21.3 — Intermediate moment frames
(a) d/4;
(d) 300 mm
Fig. R21.3.3—Design shears for intermediate moment frames.
CODE COMMENTARY
21.3.4.3 — Stirrups shall be spaced not more than To determine the maximum beam shear, it is assumed that
d/2 throughout the length of the beam. its nominal moment strengths (φ = 1.0) are developed simul-
taneously at both ends of its clear span. As indicated in Fig.
21.3.5 — Columns R21.3.3, the shear associated with this condition [(Mnl +
Mnr)/ln] is added algebraically to the shear due to the
21.3.5.1 — Columns shall be spirally reinforced in factored gravity loads to obtain the design shear for the
accordance with 7.10.4 or shall conform with 21.3.5.2 beam. For this example, both the dead load wD and the live
through 21.3.5.4. Section 21.3.5.5 shall apply to all load wL have been assumed to be uniformly distributed.
columns, and 21.3.5.6 shall apply to all columns
supporting discontinuous stiff members. Determination of the design shear for a column is also
illustrated for a particular example in Fig. R21.3.3. The
21.3.5.2 — At both ends of the column, hoops shall factored axial force, Pu , should be chosen to develop the
be provided at spacing so over a length lo measured largest moment strength of the column.
from the joint face. Spacing so shall not exceed the
smallest of (a), (b), (c), and (d): In all applications of option (a) of 21.3.3, shears are
required to be calculated for moments, acting both clock-
(a) Eight times the diameter of the smallest longitu- wise and counterclockwise. Figure R21.3.3 demonstrates
dinal bar enclosed; only one of the two conditions that are to be considered for
every member. Option (b) bases Vu on the load combination
(b) 24 times the diameter of the hoop bar; including the earthquake effect, E, which should be
(c) One-half of the smallest cross-sectional dimension doubled. For example, the load combination defined by
of the column; Eq. (9-5) would be
Length lo shall not be less than the largest of (e), (f), where E is the value specified by the governing code.
and (g):
Section 21.3.4 contains requirements for providing beams
(e) One-sixth of the clear span of the column; with a threshold level of toughness. Transverse reinforcement
(f) Maximum cross-sectional dimension of the at the ends of the beam is required to be hoops. In most
column; cases, stirrups required by 21.3.3 for design shear force will
be more than those required by 21.3.4. Requirements of
(g) 450 mm. 21.3.5 serve the same purpose for columns.
21.3.5.3 — The first hoop shall be located not more Discontinuous structural walls and other stiff members can
than so /2 from the joint face. impose large axial forces on supporting columns during
earthquakes. The required transverse reinforcement in
21.3.5.4 — Outside the length lo , spacing of trans- 21.3.5.6 is to improve column toughness under anticipated
verse reinforcement shall conform to 7.10 and demands. The factored axial compressive force related to
21 11.4.5.1. earthquake effect should include the factor Ωo if required by
the legally adopted general building code of which this
21.3.5.5 — Joint transverse reinforcement shall Code forms a part.
conform to 11.10.
Section 21.3.6 applies to two-way slabs without beams,
21.3.5.6 — Columns supporting reactions from such as flat plates.
discontinuous stiff members, such as walls, shall be
provided with transverse reinforcement at the spacing, Using load combinations of Eq. (9-5) and (9-7) may result
so , as defined in 21.3.5.2 over the full height beneath in moments requiring top and bottom reinforcement at the
the level at which the discontinuity occurs if the portion supports.
of factored axial compressive force in these members
related to earthquake effects exceeds Agfc′ /10. Where The moment Mslab refers, for a given design load combination
design forces have been magnified to account for the with E acting in one horizontal direction, to that portion of
overstrength of the vertical elements of the seismic- the factored slab moment that is balanced by the supporting
force-resisting system, the limit of Agfc′ /10 shall be members at a joint. It is not necessarily equal to the total
increased to Agfc′ /4. This transverse reinforcement design moment at support for a load combination including
CODE COMMENTARY
shall extend above and below the columns as required earthquake effect. In accordance with 13.5.3.2, only a frac-
in 21.6.4.6(b). tion of the moment Mslab is assigned to the slab effective
width. For edge and corner connections, flexural reinforce-
21.3.6 — Two-way slabs without beams ment perpendicular to the edge is not considered fully effec-
tive unless it is placed within the effective slab
21.3.6.1 — Factored slab moment at support width.21.12,21.13 See Fig. 21.3.6.1.
including earthquake effects, E, shall be determined
for load combinations given in Eq. (9-5) and (9-7). Application of the provisions of 21.3.6 is illustrated in
Reinforcement provided to resist Mslab shall be placed Fig. R21.3.6.2 and R21.3.6.3.
within the column strip defined in 13.2.1.
CODE COMMENTARY
21
Fig. R21.3.6.3—Arrangement of reinforcement in slabs.
21.3.6.8 — At the critical sections for columns R21.3.6.8 — The requirements apply to two-way slabs
defined in 11.11.1.2, two-way shear caused by that are designated part of the seismic-force-resisting
factored gravity loads shall not exceed 0.4φVc , where system. Slab-column connections in laboratory tests21.13
Vc shall be calculated as defined in 11.11.2.1 for exhibited reduced lateral displacement ductility when the
nonprestressed slabs and in 11.11.2.2 for prestressed shear at the column connection exceeded the recommended
slabs. It shall be permitted to waive this requirement if limit. Slab-column connections also must satisfy shear and
the slab design satisfies requirements of 21.13.6. moment strength requirements of Chapters 11 and 13 under
load combinations including earthquake effect.
CODE COMMENTARY
21.4 — Intermediate precast structural walls R21.4 — Intermediate precast structural walls
Requirements of 21.5 apply to special moment frame This section refers to beams of special moment frames
members that form part of the seismic-force-resisting resisting lateral loads induced by earthquake motions. Any
system and are proportioned primarily to resist flexure. frame member subjected to a factored axial compressive
These frame members shall also satisfy the conditions force exceeding (Ag fc′ /10) under any load combination is to
of 21.5.1.1 through 21.5.1.4. be proportioned and detailed as described in 21.6.
21.5.1.1 — Factored axial compressive force on the Experimental evidence21.14 indicates that, under reversals of
member, Pu, shall not exceed Agfc′ /10. displacement into the nonlinear range, behavior of continuous
members having length-to-depth ratios of less than 4 is
21.5.1.2 — Clear span for member, ln, shall not be significantly different from the behavior of relatively
less than four times its effective depth. slender members. Design rules derived from experience
with relatively slender members do not apply directly to
21.5.1.3 — Width of member, bw , shall not be less members with length-to-depth ratios less than 4, especially
than the smaller of 0.3h and 250 mm. with respect to shear strength.
21.5.1.4 — Width of member, bw, shall not exceed Geometric constraints indicated in 21.5.1.3 and 21.5.1.4
width of supporting member, c2, plus a distance on were derived from practice and research21.8 on reinforced
each side of supporting member equal to the smaller concrete frames resisting earthquake-induced forces. The
of (a) and (b): limits in 21.5.1.4 recognize that the maximum effective 21
beam width depends principally on the column dimensions
(a) Width of supporting member, c2, and rather than on the depth of the beam, as suggested in the
2005 and earlier versions of the Code. An example of
(b) 0.75 times the overall dimension of supporting maximum effective beam width is shown in Fig. R21.5.1.
member, c1.
CODE COMMENTARY
21
CODE COMMENTARY
21.5.2.1 — At any section of a flexural member, R21.5.2.1 — The limiting reinforcement ratio of 0.025 is
except as provided in 10.5.3, for top as well as for based primarily on considerations of steel congestion and,
bottom reinforcement, the amount of reinforcement indirectly, on limiting shear stresses in beams of typical
shall not be less than that given by Eq. (10-3) but not proportions. The requirement of at least two bars, top and
less than 1.4bwd/fy , and the reinforcement ratio, ρ, bottom, refers again to construction rather than behavioral
shall not exceed 0.025. At least two bars shall be requirements.
provided continuously at both top and bottom.
21.5.2.3 — Lap splices of flexural reinforcement R21.5.2.3 — Lap splices of reinforcement are prohibited
shall be permitted only if hoop or spiral reinforcement at regions where flexural yielding is anticipated because
is provided over the lap length. Spacing of the trans- such splices are not reliable under conditions of cyclic
verse reinforcement enclosing the lap-spliced bars loading into the inelastic range. Transverse reinforcement
shall not exceed the smaller of d/4 and 100 mm. Lap for lap splices at any location is mandatory because of the
splices shall not be used: likelihood of loss of shell concrete.
21.5.2.5 — Prestressing, where used, shall satisfy R21.5.2.5 — These provisions were developed, in part,
(a) through (d), unless used in a special moment based on observations of building performance in earth-
frame as permitted by 21.8.3: quakes.21.15 For calculating the average prestress, the
smallest cross-sectional dimension in a beam normally is
(a) The average prestress, fpc , calculated for an the web dimension, and is not intended to refer to the flange
area equal to the smallest cross-sectional dimension thickness. In a potential plastic hinge region, the limitation 21
of the member multiplied by the perpendicular cross- on strain and the requirement for unbonded tendons are
sectional dimension shall not exceed the smaller of intended to prevent fracture of tendons under inelastic earth-
3.5 MPa and fc′ /10. quake deformation. Calculation of the strain in the prestressing
steel is required considering the anticipated inelastic mecha-
(b) Prestressing steel shall be unbonded in potential nism of the structure. For prestressing steel unbonded along
plastic hinge regions, and the calculated strains in the full beam span, strains generally will be well below the
prestressing steel under the design displacement specified limit. For prestressing steel with short unbonded
shall be less than 1 percent. length through or adjacent to the joint, the additional strain
(c) Prestressing steel shall not contribute to more due to earthquake deformation is calculated as the product
than one-quarter of the positive or negative flexural of the depth to the neutral axis and the sum of plastic hinge
strength at the critical section in a plastic hinge rotations at the joint, divided by the unbonded length.
region and shall be anchored at or beyond the exterior
face of the joint. The restrictions on the flexural strength provided by the
tendons are based on the results of analytical and experi-
(d) Anchorages of the post-tensioning tendons mental studies.21.16-21.18 Although satisfactory seismic
resisting earthquake-induced forces shall be performance can be obtained with greater amounts of
CODE COMMENTARY
capable of allowing tendons to withstand 50 cycles prestressing steel, this restriction is needed to allow the use
of loading, bounded by 40 and 85 percent of the of the same response modification and deflection amplification
specified tensile strength of the prestressing steel. factors as those specified in model codes for special
moment frames without prestressing steel. Prestressed
special moment frames will generally contain continuous
prestressing steel that is anchored with adequate cover at or
beyond the exterior face of each beam-column connection
located at the ends of the moment frame.
21.5.3.1 — Hoops shall be provided in the following Transverse reinforcement is required primarily to confine
regions of frame members: the concrete and maintain lateral support for the reinforcing
bars in regions where yielding is expected. Examples of
(a) Over a length equal to twice the member depth hoops suitable for flexural members of frames are shown in
measured from the face of the supporting member Fig. R21.5.3.
toward midspan, at both ends of the flexural
member; In the case of members with varying strength along the span
or members for which the permanent load represents a large
(b) Over lengths equal to twice the member depth on proportion of the total design load, concentrations of
both sides of a section where flexural yielding is inelastic rotation may occur within the span. If such a
likely to occur in connection with inelastic lateral condition is anticipated, transverse reinforcement also
displacements of the frame. should be provided in regions where yielding is expected.
21.5.3.2 — The first hoop shall be located not more
than 2 in. from the face of a supporting member.
Spacing of the hoops shall not exceed the smallest of
(a), (b), (c) and (d):
(a) d/4;
21
(b) Eight times the diameter of the smallest longitu-
dinal bars;
CODE COMMENTARY
21.5.3.5 — Stirrups or ties required to resist shear Because spalling of the concrete shell is anticipated during
shall be hoops over lengths of members in 21.5.3.1. strong motion, especially at and near regions of flexural
yielding, all web reinforcement should be provided in the
21.5.3.6 — Hoops in flexural members shall be form of closed hoops as defined in 21.5.3.5.
permitted to be made up of two pieces of reinforce-
ment: a stirrup having seismic hooks at both ends and
closed by a crosstie. Consecutive crossties engaging
the same longitudinal bar shall have their 90-degree
hooks at opposite sides of the flexural member. If the
longitudinal reinforcing bars secured by the crossties
are confined by a slab on only one side of the flexural
frame member, the 90-degree hooks of the crossties
shall be placed on that side.
The design shear force, Ve , shall be determined from In determining the equivalent lateral forces representing
consideration of the statical forces on the portion of earthquake effects for the type of frames considered, it is
the member between faces of the joints. It shall be assumed that frame members will dissipate energy in the
assumed that moments of opposite sign corresponding nonlinear range of response. Unless a frame member
to probable flexural moment strength, Mpr , act at the possesses a strength that is on the order of 3 or 4 of the
joint faces and that the member is loaded with the design forces, it should be assumed that it will yield in the
factored tributary gravity load along its span. event of a major earthquake. The design shear force should
be a good approximation of the maximum shear that may
develop in a member. Therefore, required shear strength for
frame members is related to flexural strengths of the
designed member rather than to factored shear forces indi-
cated by lateral load analysis. The conditions described by
21.5.4.1 are illustrated in Fig. R21.5.4.
Transverse reinforcement over the lengths identified in Experimental studies21.20,21.21 of reinforced concrete
21.5.3.1 shall be proportioned to resist shear members subjected to cyclic loading have demonstrated that
assuming Vc = 0 when both (a) and (b) occur: more shear reinforcement is required to ensure a flexural
failure if the member is subjected to alternating nonlinear
(a) The earthquake-induced shear force calculated displacements than if the member is loaded in only one
in accordance with 21.5.4.1 represents one-half or direction: the necessary increase of shear reinforcement
more of the maximum required shear strength within being higher in the case of no axial load. This observation is
those lengths; reflected in the Code (see 21.5.4.2) by eliminating the term
representing the contribution of concrete to shear strength.
(b) The factored axial compressive force, Pu , The added conservatism on shear is deemed necessary in
including earthquake effects is less than Agfc′ /20. locations where potential flexural hinging may occur.
However, this stratagem, chosen for its relative simplicity,
should not be interpreted to mean that no concrete is
required to resist shear. On the contrary, it may be argued
that the concrete core resists all the shear with the shear
CODE COMMENTARY
21
CODE COMMENTARY
(transverse) reinforcement confining and strengthening the
concrete. The confined concrete core plays an important
role in the behavior of the beam and should not be reduced
to a minimum just because the design expression does not
explicitly recognize it.
21.6 — Special moment frame members R21.6 — Special moment frame members
subjected to bending and axial load subjected to bending and axial load
Requirements of this section apply to special moment Section 21.6.1 is intended primarily for columns of special
frame members that form part of the seismic-force- moment frames. Frame members, other than columns, that
resisting system and that resist a factored axial do not satisfy 21.5.1 are to be proportioned and detailed
compressive force Pu under any load combination according to this section. These provisions apply to the
exceeding Agfc′ /10. These frame members shall also frame member for all load combinations if the axial load
satisfy the conditions of 21.6.1.1 and 21.6.1.2. exceeds 0.1Ag fc′ in any load combination.
21.6.1.1 — The shortest cross-sectional dimension, The geometric constraints in 21.6.1.1 and 21.6.1.2 follow
measured on a straight line passing through the from previous practice.21.22
geometric centroid, shall not be less than 300 mm.
21.6.2 — Minimum flexural strength of columns R21.6.2 — Minimum flexural strength of columns
21.6.2.1 — Columns shall satisfy 21.6.2.2 or The intent of 21.6.2.2 is to reduce the likelihood of yielding
21.6.2.3. in columns that are considered as part of the seismic-force-
resisting system. If columns are not stronger than beams
21.6.2.2 — The flexural strengths of the columns framing into a joint, there is likelihood of inelastic action. In
shall satisfy Eq. (21-1) the worst case of weak columns, flexural yielding can occur
at both ends of all columns in a given story, resulting in a
ΣMnc ≥ (1.2)ΣMnb (21-1) column failure mechanism that can lead to collapse.
ΣMnc = sum of nominal flexural strengths of columns In 21.6.2.2, the nominal strengths of the girders and
framing into the joint, evaluated at the faces of the columns are calculated at the joint faces, and those strengths
joint. Column flexural strength shall be calculated for are compared directly using Eq. (21-1). The 1995 Code
21
the factored axial force, consistent with the direction of required design strengths to be compared at the center of the
the lateral forces considered, resulting in the lowest joint, which typically produced similar results but with
flexural strength. added computational effort.
ΣMnb = sum of nominal flexural strengths of the beams When determining the nominal flexural strength of a girder
framing into the joint, evaluated at the faces of the section in negative bending (top in tension), longitudinal
joint. In T-beam construction, where the slab is in tension reinforcement contained within an effective flange width of
under moments at the face of the joint, slab reinforce- a top slab that acts monolithically with the girder increases
ment within an effective slab width defined in 8.12 shall the girder strength. Research21.23 on beam-column
be assumed to contribute to Mnb if the slab reinforce- subassemblies under lateral loading indicates that using the
ment is developed at the critical section for flexure. effective flange widths defined in 8.10 gives reasonable
estimates of girder negative bending strengths of interior
Flexural strengths shall be summed such that the column connections at interstory displacement levels approaching
moments oppose the beam moments. Equation (21-1) 2 percent of story height. This effective width is conservative
shall be satisfied for beam moments acting in both where the slab terminates in a weak spandrel.
directions in the vertical plane of the frame considered.
CODE COMMENTARY
21.6.2.3 — If 21.6.2.2 is not satisfied at a joint, the If 21.6.2.2 cannot be satisfied at a joint, 21.6.2.3 requires
lateral strength and stiffness of the columns framing that any positive contribution of the column or columns
into that joint shall be ignored when determining the involved to the lateral strength and stiffness of the structure
calculated strength and stiffness of the structure. is to be ignored. Negative contributions of the column or
These columns shall conform to 21.13. columns should not be ignored. For example, ignoring the
stiffness of the columns ought not be used as a justification
for reducing the design base shear. If inclusion of those
columns in the analytical model of the building results in an
increase in torsional effects, the increase should be considered
as required by the governing code. Furthermore, the column
must be provided with transverse reinforcement to increase
its toughness to resist shear and axial forces.
21.6.3.1 — Area of longitudinal reinforcement, Ast , The lower limit of the area of longitudinal reinforcement is
shall not be less than 0.01Ag or more than 0.06Ag . to control time-dependent deformations and to have the
yield moment exceed the cracking moment. The upper limit
21.6.3.2 — Mechanical splices shall conform to of the section reflects concern for steel congestion, load
21.1.6 and welded splices shall conform to 21.1.7. Lap transfer from floor elements to column (especially in low-rise
splices shall be permitted only within the center half of construction) and the development of high shear stresses.
the member length, shall be designed as tension lap
splices, and shall be enclosed within transverse Spalling of the shell concrete, which is likely to occur near
reinforcement conforming to 21.6.4.2 and 21.6.4.3. the ends of the column in frames of typical configuration,
makes lap splices in these locations vulnerable. If lap
splices are to be used at all, they should be located near the
midheight where stress reversal is likely to be limited to a
smaller stress range than at locations near the joints.
Transverse reinforcement is required along the lap-splice
length because of the uncertainty in moment distributions
along the height and the need for confinement of lap splices
subjected to stress reversals.21.24
21.6.4.2 — Transverse reinforcement shall be R21.6.4.2 — Sections 21.6.4.2 and 21.6.4.3 provide
provided by either single or overlapping spirals satis- requirements for configuration of transverse reinforcement for
fying 7.10.4, circular hoops, or rectilinear hoops with or columns and joints of special moment frames. Figure R21.6.4.2
CODE COMMENTARY
without crossties. Crossties of the same or smaller bar
size as the hoops shall be permitted. Each end of the
crosstie shall engage a peripheral longitudinal reinforcing
bar. Consecutive crossties shall be alternated end for
end along the longitudinal reinforcement. Spacing of
crossties or legs of rectilinear hoops, hx , within a cross
section of the member shall not exceed 350 mm on
center.
21.6.4.3 — Spacing of transverse reinforcement R21.6.4.3 — The requirement that spacing not exceed
along the length lo of the member shall not exceed the one-quarter of the minimum member dimension is to obtain
smallest of (a), (b), and (c): adequate concrete confinement. The requirement that
spacing not exceed six bar diameters is intended to restrain
(a) One-quarter of the minimum member dimension; longitudinal reinforcement buckling after spalling. The
100 mm spacing is for concrete confinement; 21.6.4.3
(b) Six times the diameter of the smallest longitu- permits this limit to be relaxed to a maximum of 150 mm if
dinal bar; and 21
the spacing of crossties or legs of overlapping hoops is less
(c) so , as defined by Eq. (21-2) than 200 mm.
350 – h
s o = 100 + ⎛ ---------------------x-⎞ (21-2)
⎝ 3 ⎠
21.6.4.4 — Amount of transverse reinforcement R21.6.4.4 — The effect of helical (spiral) reinforcement
required in (a) or (b) shall be provided unless a larger and adequately configured rectilinear hoop reinforcement
amount is required by 21.6.5. on strength and ductility of columns is well established.21.26
While analytical procedures exist for calculation of strength
(a) The volumetric ratio of spiral or circular hoop and ductility capacity of columns under axial and moment
reinforcement, ρs , shall not be less than required by reversals,21.27 the axial load and deformation demands
Eq. (21-3) during earthquake loading are not known with sufficient
CODE COMMENTARY
fc ′ accuracy to justify calculation of required transverse
ρ s = 0.12 ------ (21-3) reinforcement as a function of design earthquake demands.
f yt
Instead, Eq. (10-5) and (21-4) are required, with the intent
that spalling of shell concrete will not result in a loss of axial
and shall not be less than required by Eq. (10-5). load strength of the column. Equations (21-3) and (21-5)
govern for large-diameter columns, and are intended to
(b) The total cross-sectional area of rectangular
ensure adequate flexural curvature capacity in yielding
hoop reinforcement, Ash , shall not be less than
regions.
required by Eq. (21-4) and (21-5)
Equations (21-4) and (21-5) are to be satisfied in both cross-
sb c f c′ ⎛ A g ⎞
- ---------- – 1
Ash = 0.3 ---------------- (21-4) sectional directions of the rectangular core. For each direc-
f yt ⎝ A ch⎠ tion, bc is the core dimension perpendicular to the tie legs
that constitute Ash , as shown in Fig. R21.6.4.2.
sb c f c′
Ash = 0.09 ----------------
- (21-5) Research results indicate that yield strengths higher than
f yt those specified in 11.4.2 can be used effectively as confinement
reinforcement. A fyt of 700 MPa is permitted in Eq. (21-3),
(21-4), and (21-5) where ASTM A1035M is used as confine-
ment reinforcement.
21.6.4.5 — Beyond the length lo specified in R21.6.4.5 — The provisions of 21.6.4.5 are intended to
21.6.4.1, the column shall contain spiral or hoop provide reasonable protection and ductility to the
reinforcement satisfying 7.10 with center-to-center midheight of columns outside the length lo. Observations
spacing, s, not exceeding the smaller of six times the after earthquakes have shown significant damage to
diameter of the smallest longitudinal column bars and columns in this region, and the minimum ties or spirals
150 mm, unless a larger amount of transverse rein- required should provide a more uniform toughness of the
forcement is required by 21.6.3.2 or 21.6.5. column along its length.
21.6.4.6 — Columns supporting reactions from R21.6.4.6 — Columns supporting discontinued stiff
discontinued stiff members, such as walls, shall satisfy members, such as walls or trusses, may develop consider-
(a) and (b): able inelastic response. Therefore, it is required that these
columns have the specified reinforcement throughout their
(a) Transverse reinforcement as required in 21.6.4.2 length. This covers all columns beneath the level at which
through 21.6.4.4 shall be provided over their full the stiff member has been discontinued, unless the factored
height at all levels beneath the discontinuity if the forces corresponding to earthquake effect are low. See
factored axial compressive force in these members, R21.11.7.5 for discussion of the overstrength factor Ωo
related to earthquake effect, exceeds Agfc′ /10. applied in some codes.
Where design forces have been magnified to
account for the overstrength of the vertical elements
21 of the seismic-force-resisting system, the limit of
Agfc′ /10 shall be increased to Agfc′ /4.
(b) The transverse reinforcement shall extend into
the discontinued member at least ld of the largest
longitudinal column bar, where ld is determined in
accordance with 21.7.5. Where the lower end of the
column terminates on a wall, the required transverse
reinforcement shall extend into the wall at least ld of
the largest longitudinal column bar at the point of
termination. Where the column terminates on a
footing or mat, the required transverse reinforcement
shall extend at least 300 mm into the footing or mat.
21.6.4.7 — If the concrete cover outside the R21.6.4.7 — The unreinforced shell may spall as the
confining transverse reinforcement specified in 21.6.4.1, column deforms to resist earthquake effects. Separation of
21.6.4.5, and 21.6.4.6 exceeds 100 mm, additional portions of the shell from the core caused by local spalling
CODE COMMENTARY
transverse reinforcement shall be provided. Concrete creates a falling hazard. The additional reinforcement is
cover for additional transverse reinforcement shall not required to reduce the risk of portions of the shell falling
exceed 100 mm and spacing of additional trans- away from the column.
verse reinforcement shall not exceed 300 mm.
The design shear force, Ve , shall be determined from The procedures of 21.5.4.1 also apply to members subjected
consideration of the maximum forces that can be to axial loads (for example, columns). Above the ground
generated at the faces of the joints at each end of the floor, the moment at a joint may be limited by the flexural
member. These joint forces shall be determined using strength of the beams framing into the joint. Where beams
the maximum probable moment strengths, Mpr , at frame into opposite sides of a joint, the combined strength
each end of the member associated with the range of may be the sum of the negative moment strength of the
factored axial loads, Pu , acting on the member. The beam on one side of the joint and the positive moment
member shears need not exceed those determined strength of the beam on the other side of the joint. Moment
from joint strengths based on Mpr of the transverse strengths are to be determined using a strength reduction
members framing into the joint. In no case shall Ve be factor of 1.0 and reinforcing steel stress equal to at least
less than the factored shear determined by analysis of 1.25fy. Distribution of the combined moment strength of the
the structure. beams to the columns above and below the joint should be
based on analysis. The value of Mpr in Fig. R21.5.4 may be
computed from the flexural member strengths at the beam-
column joints.
21.7 — Joints of special moment frames R21.7 — Joints of special moment frames
21
21.7.1 — Scope
21.7.2.1 — Forces in longitudinal beam reinforcement Development of inelastic rotations at the faces of joints of
at the joint face shall be determined by assuming that reinforced concrete frames is associated with strains in the
the stress in the flexural tensile reinforcement is flexural reinforcement well in excess of the yield strain. Conse-
1.25fy . quently, joint shear force generated by the flexural reinforce-
ment is calculated for a stress of 1.25fy in the reinforcement
21.7.2.2 — Beam longitudinal reinforcement (see 21.7.2.1). A detailed explanation of the reasons for the
terminated in a column shall be extended to the far possible development of stresses in excess of the yield strength
face of the confined column core and anchored in in beam tensile reinforcement is provided in Reference 21.8.
CODE COMMENTARY
tension according to 21.7.5 and in compression
according to Chapter 12.
21.7.2.3 — Where longitudinal beam reinforcement R21.7.2.3 — Research21.28-21.32 has shown that straight
extends through a beam-column joint, the column beam bars may slip within the beam-column joint during a
dimension parallel to the beam reinforcement shall not series of large moment reversals. The bond stresses on these
be less than 20 times the diameter of the largest longi- straight bars may be very large. To reduce slip substantially
tudinal beam bar for normalweight concrete. For light- during the formation of adjacent beam hinging, it would be
weight concrete, the dimension shall be not less than necessary to have a ratio of column dimension to bar diam-
26 times the bar diameter. eter of approximately 1/32, which would result in very large
joints. On reviewing the available tests, the limit of 1/20 of
the column depth in the direction of loading for the
maximum size of beam bars for normalweight concrete and
a limit of 1/26 for lightweight concrete were chosen. Due to
the lack of specific data for beam bars through lightweight
concrete joints, the limit was based on the amplification
factor of 1.3 in Chapter 12 starting with the 1989 Code. The
amplification factor was modified slightly in 2008 to 1/0.75
= 1.33, which did not affect this Code section. These limits
provide reasonable control on the amount of potential slip of
the beam bars in a beam-column joint, considering the
number of anticipated inelastic excursions of the building
frames during a major earthquake. A thorough treatment of
this topic is given in Reference 21.33.
21.7.3.1 — Joint transverse reinforcement shall The Code requires transverse reinforcement in a joint
satisfy either 21.6.4.4(a) or 21.6.4.4(b), and shall also regardless of the magnitude of the calculated shear force. In
satisfy 21.6.4.2, 21.6.4.3, and 21.6.4.7, except as 21.7.3.2, the amount of confining reinforcement may be
permitted in 21.7.3.2. reduced and the spacing may be increased if horizontal
members frame into all four sides of the joint.
21.7.3.2 — Where members frame into all four sides
of the joint and where each member width is at least Section 21.7.3.3 refers to a joint where the width of the beam
three-fourths the column width, the amount of reinforce- exceeds the corresponding column dimension. In that case,
ment specified in 21.6.4.4(a) or 21.6.4.4(b) shall be beam reinforcement not confined by the column reinforcement
permitted to be reduced by half, and the spacing should be provided lateral support either by a beam framing
required in 21.6.4.3 shall be permitted to be increased into the same joint or by transverse reinforcement.
to 150 mm within the overall depth h of the shallowest
21 framing member. An example of transverse reinforcement through the column
provided to confine the beam reinforcement passing outside
21.7.3.3 — Longitudinal beam reinforcement outside the column core is shown in Fig. R21.5.1. Additional
the column core shall be confined by transverse detailing guidance and design recommendations for both
reinforcement passing through the column that satisfies interior and exterior wide-beam connections with beam
spacing requirements of 21.5.3.2, and requirements of reinforcement passing outside the column core may be
21.5.3.3 and 21.5.3.6, if such confinement is not found in Reference 21.8.
provided by a beam framing into the joint.
21.7.4.1 — Vn of the joint shall not be taken as The requirements in Chapter 21 for proportioning joints are
greater than the values specified below for normal- based on Reference 21.8 in that behavioral phenomena
weight concrete. within the joint are interpreted in terms of a nominal shear
strength of the joint. Because tests of joints21.28 and deep
For joints confined on all four faces .......... 1.7 f c′ Aj beams21.14 indicated that shear strength was not as sensitive
CODE COMMENTARY
For joints confined on three faces or to joint (shear) reinforcement as implied by the expression
on two opposite faces............................... 1.2 f c′ Aj developed by Joint ACI-ASCE Committee 32621.34 for
beams, Committee 318 set the strength of the joint as a
For others ................................................. 1.0 f c′ Aj function of only the compressive strength of the concrete
A member that frames into a face is considered to (see 21.7.4) and requires a minimum amount of transverse
provide confinement to the joint if at least three-quarters reinforcement in the joint (see 21.7.3). The effective area of
of the face of the joint is covered by the framing joint Aj is illustrated in Fig. R21.7.4. In no case is Aj greater
member. Extensions of beams at least one overall than the column cross-sectional area.
beam depth h beyond the joint face are permitted to
be considered as confining members. Extensions of The three levels of shear strength required by 21.7.4.1 are
beams shall satisfy 21.5.1.3, 21.5.2.1, 21.5.3.2, based on the recommendation of ACI Committee 352.21.8
21.5.3.3, and 21.5.3.6. A joint is considered to be Test data reviewed by the committee21.35 indicate that the
confined if such confining members frame into all lower value given in 21.7.4.1 of the 1983 Code was uncon-
faces of the joint. servative when applied to corner joints.
Aj is the effective cross-sectional area within a joint Cyclic loading tests of joints with extensions of beams with
computed from joint depth times effective joint width. lengths at least equal to their depths have indicated similar
Joint depth shall be the overall depth of the column, h. joint shear strengths to those of joints with continuous
Effective joint width shall be the overall width of the beams. These findings suggest that extensions of beams,
column, except where a beam frames into a wider when properly dimensioned and reinforced with longitu-
column, effective joint width shall not exceed the dinal and transverse bars, provide effective confinement to
smaller of (a) and (b): the joint faces, thus delaying joint strength deterioration at
large deformations.21.36
(a) Beam width plus joint depth
(b) Twice the smaller perpendicular distance from
longitudinal axis of beam to column side.
21
CODE COMMENTARY
21.7.5 — Development length of bars in tension R21.7.5 — Development length of bars in tension
21.7.5.1 — For bar sizes No. 10 through No. 36, the Minimum development length in tension for deformed bars
development length, ldh , for a bar with a standard with standard hooks embedded in normalweight concrete is
90-degree hook in normalweight concrete shall not be determined using Eq. (21-6), which is based on the require-
less than the largest of 8db , 150 mm, and the length ments of 12.5. Because Chapter 21 stipulates that the hook
required by Eq. (21-6) is to be embedded in confined concrete, the coefficients 0.7
(for concrete cover) and 0.8 (for ties) have been incorporated
fy db in the constant used in Eq. (21-6). The development length
ldh = ------------------
- (21-6) that would be derived directly from 12.5 is increased to
5.4 f c ′ reflect the effect of load reversals.
For lightweight concrete, ldh for a bar with a standard The development length in tension of a deformed bar with a
90-degree hook shall not be less than the largest of standard hook is defined as the distance, parallel to the bar,
10db , 190 mm, and 1.25 times the length required by from the critical section (where the bar is to be developed) to a
Eq. (21-6). tangent drawn to the outside edge of the hook. The tangent is to
be drawn perpendicular to the axis of the bar (see Fig. R12.5).
The 90-degree hook shall be located within the
confined core of a column or of a boundary element. Factors such as the actual stress in the reinforcement being
more than the yield stress and the effective development
21.7.5.2 — For bar sizes No. 10 through No. 36, ld , length not necessarily starting at the face of the joint were
the development length in tension for a straight bar, implicitly considered in the development of the expression
shall not be less than the larger of (a) and (b): for basic development length that has been used as the basis
for Eq. (21-6).
(a) 2.5 times the length required by 21.7.5.1 if the
depth of the concrete cast in one lift beneath the bar For lightweight concrete, the length required by Eq. (21-6)
does not exceed 300 mm; is to be increased by 25 percent to compensate for variability
of bond characteristics of reinforcing bars in various types
(b) 3.25 times the length required by 21.7.5.1 if the of lightweight concrete.
depth of the concrete cast in one lift beneath the bar
exceeds 300 mm. Section 21.7.5.2 specifies the minimum development length
21.7.5.3 — Straight bars terminated at a joint shall in tension for straight bars as a multiple of the length indicated
pass through the confined core of a column or of a by 21.7.5.1. Section 21.7.5.2(b) refers to top bars.
boundary element. Any portion of ld not within the
confined core shall be increased by a factor of 1.6. If the required straight embedment length of a reinforcing bar
extends beyond the confined volume of concrete (as defined
21.7.5.4 — If epoxy-coated reinforcement is used, in 21.5.3, 21.6.4, or 21.7.3), the required development length
the development lengths in 21.7.5.1 through 21.7.5.3 is increased on the premise that the limiting bond stress
shall be multiplied by applicable factors in 12.2.4 or outside the confined region is less than that inside.
21 12.5.2.
ldm = 1.6(ld – ldc) + ldc
oder
where
ldm = required development length if bar is not entirely
embedded in confined concrete;
ld = required development length in tension for straight
bar embedded in confined concrete;
ldc = length of bar embedded in confined concrete.
CODE COMMENTARY
21.8 — Special moment frames R21.8 — Special moment frames
constructed using precast concrete constructed using precast concrete
21.8.1 — Scope The detailing provisions in 21.8.2 and 21.8.3 are intended to
produce frames that respond to design displacements essen-
Requirements of 21.8 apply to special moment frames tially like monolithic special moment frames.
constructed using precast concrete forming part of the
seismic-force-resisting system. Precast frame systems composed of concrete elements with
ductile connections are expected to experience flexural
21.8.2 — Special moment frames with ductile yielding in connection regions. Reinforcement in ductile
connections constructed using precast concrete shall connections can be made continuous by using Type 2
satisfy (a) and (b) and all requirements for special mechanical splices or any other technique that provides
moment frames constructed with cast-in-place concrete: development in tension or compression of at least 125 percent
of the specified yield strength fy of bars and the specified
(a) Vn for connections computed according to 11.6.4 tensile strength of bars.21.37-21.40 Requirements for mechanical
shall not be less than 2Ve , where Ve is calculated splices are in addition to those in 21.1.6 and are intended to
according to 21.5.4.1 or 21.6.5.1; avoid strain concentrations over a short length of reinforcement
adjacent to a splice device. Additional requirements for
(b) Mechanical splices of beam reinforcement shall shear strength are provided in 21.8.2 to prevent sliding on
be located not closer than h/2 from the joint face connection faces. Precast frames composed of elements
and shall meet the requirements of 21.1.6. with ductile connections may be designed to promote
21.8.3 — Special moment frames with strong yielding at locations not adjacent to the joints. Therefore,
connections constructed using precast concrete shall design shear, Ve , as computed according to 21.5.4.1 or
satisfy all requirements for special moment frames 21.6.5.1, may be conservative.
constructed with cast-in-place concrete, as well as (a),
(b), (c), and (d). Precast concrete frame systems composed of elements
joined using strong connections are intended to experience
(a) Provisions of 21.5.1.2 shall apply to segments flexural yielding outside the connections. Strong connec-
between locations where flexural yielding is intended tions include the length of the coupler hardware as shown in
to occur due to design displacements; Fig. R21.8.3. Capacity-design techniques are used in
21.8.3(b) to ensure the strong connection remains elastic
(b) Design strength of the strong connection, φSn, following formation of plastic hinges. Additional column
shall be not less than Se ; requirements are provided to avoid hinging and strength
deterioration of column-to-column connections.
(c) Primary longitudinal reinforcement shall be made
continuous across connections and shall be developed Strain concentrations have been observed to cause brittle
outside both the strong connection and the plastic fracture of reinforcing bars at the face of mechanical splices
hinge region; and in laboratory tests of precast beam-column connections.21.41
(d) For column-to-column connections, φSn shall not Locations of strong connections should be selected care-
21
be less than 1.4Se . At column-to-column connec- fully or other measures should be taken, such as debonding
tions, φMn shall be not less than 0.4Mpr for the of reinforcing bars in highly stressed regions, to avoid strain
column within the story height, and φVn of the concentrations that can result in premature fracture of
connection shall be not less than Ve determined by reinforcement.
21.6.5.1.
21.8.4 — Special moment frames constructed using R21.8.4 — Precast frame systems not satisfying the prescrip-
precast concrete and not satisfying the requirements tive requirements of Chapter 21 have been demonstrated in
of 21.8.2 or 21.8.3 shall satisfy the requirements of experimental studies to provide satisfactory seismic
ACI 374.1 and the requirements of (a) and (b): performance characteristics.21.42,21.43 ACI 374.1 defines a
protocol for establishing a design procedure, validated by
(a) Details and materials used in the test specimens analysis and laboratory tests, for such frames. The design
shall be representative of those used in the structure; procedure should identify the load path or mechanism by
and which the frame resists gravity and earthquake effects. The
tests should be configured to test critical behaviors, and the
(b) The design procedure used to proportion the test measured quantities should establish upper-bound acceptance
specimens shall define the mechanism by which the
CODE COMMENTARY
21
CODE COMMENTARY
frame resists gravity and earthquake effects, and values for components of the load path, which may be in
shall establish acceptance values for sustaining that terms of limiting stresses, forces, strains, or other quantities.
mechanism. Portions of the mechanism that deviate The design procedure used for the structure should not
from Code requirements shall be contained in the deviate from that used to design the test specimens, and
test specimens and shall be tested to determine acceptance values should not exceed values that were
upper bounds for acceptance values. demonstrated by the tests to be acceptable. Materials and
components used in the structure should be similar to those
used in the tests. Deviations may be acceptable if the
licensed design professional can demonstrate that those
deviations do not adversely affect the behavior of the
framing system.
21.9 — Special structural walls and R21.9 — Special structural walls and
coupling beams coupling beams
Requirements of 21.9 apply to special structural walls, This section contains requirements for the dimensions and
cast-in-place or precast, and coupling beams forming details of special structural walls and coupling beams.
part of the seismic-force-resisting system. Special
structural walls constructed using precast concrete
shall also comply with 21.10.
21.9.2.1 — The distributed web reinforcement ratios, Minimum reinforcement requirements in 21.9.2.1 follow
ρl and ρt , for structural walls shall not be less than from preceding Codes. The uniform distribution requirement
0.0025, except that if Vu does not exceed 0.083Acvλ f c′ , of the shear reinforcement is related to the intent to control
ρl and ρt shall be permitted to be reduced to the the width of inclined cracks. The requirement for two layers
values required in 14.3. Reinforcement spacing each of reinforcement in walls carrying substantial design shears
way in structural walls shall not exceed 450 mm. in 21.9.2.2 is based on the observation that, under ordinary
Reinforcement contributing to Vn shall be continuous construction conditions, the probability of maintaining a
and shall be distributed across the shear plane. single layer of reinforcement near the middle of the wall
section is quite low. Furthermore, presence of reinforcement
21.9.2.2 — At least two curtains of reinforcement close to the surface tends to inhibit fragmentation of the
21
shall be used in a wall if Vu exceeds 0.17Acvλ f c′ . concrete in the event of severe cracking during an earthquake.
21.9.2.3 — Reinforcement in structural walls shall be R21.9.2.3 — Requirements are based on provisions in
developed or spliced for fy in tension in accordance Chapter 12. Because actual forces in longitudinal reinforce-
with Chapter 12, except: ment of structural walls may exceed calculated forces,
reinforcement should be developed or spliced to reach the
(a) The effective depth of the member referenced in yield strength of the bar in tension. Requirements of 12.11,
12.10.3 shall be permitted to be taken as 0.8lw for 12.12, and 12.13 address issues related to beams and do not
walls. apply to walls. At locations where yielding of longitudinal
reinforcement is expected, a 1.25 multiplier is applied to
(b) The requirements of 12.11, 12.12, and 12.13 account for the likelihood that the actual yield strength
need not be satisfied. exceeds the specified yield strength of the bar, as well as the
(c) At locations where yielding of longitudinal reinforce- influence of strain hardening and cyclic load reversals.
ment is likely to occur as a result of lateral Where transverse reinforcement is used, development
displacements, development lengths of longitudinal lengths for straight and hooked bars may be reduced as
CODE COMMENTARY
reinforcement shall be 1.25 times the values calculated permitted in 12.2 and 12.5, respectively, because closely
for fy in tension. spaced transverse reinforcement improves the performance of
splices and hooks subjected to repeated inelastic demands.21.45
(d) Mechanical splices of reinforcement shall
conform to 21.1.6 and welded splices of reinforce-
ment shall conform to 21.1.7.
Vu shall be obtained from the lateral load analysis in Design shears for structural walls are obtained from lateral
accordance with the factored load combinations. load analysis with the appropriate load factors. However, the
possibility of yielding in components of such structures
should be considered, as in the portion of a wall between
two window openings, in which case the actual shear may
be in excess of the shear indicated by lateral load analysis
based on factored design forces.
21.9.4.1 — Vn of structural walls shall not exceed Equation (21-7) recognizes the higher shear strength of
walls with high shear-to-moment ratios.21.14, 21.34, 21.46 The
Vn = Acv(αcλ f c′ + ρtfy) (21-7) nominal shear strength is given in terms of the net area of
the section resisting shear. For a rectangular section without
openings, the term Acv refers to the gross area of the cross
where the coefficient αc is 0.25 for hw /lw ≤ 1.5, is 0.17 section rather than to the product of the width and the effective
for hw /lw ≥ 2.0, and varies linearly between 0.25 and depth. The definition of Acv in Eq. (21-7) facilitates design
0.17 for hw /lw between 1.5 and 2.0. calculations for walls with uniformly distributed reinforcement
and walls with openings.
21.9.4.2 — In 21.9.4.1, the value of ratio hw /lw used
for determining Vn for segments of a wall shall be the A wall segment refers to a part of a wall bounded by openings
larger of the ratios for the entire wall and the segment or by an opening and an edge. Traditionally, a vertical wall
of wall considered. segment bounded by two window openings has been
referred to as a pier. When designing an isolated wall or a
21.9.4.3 — Walls shall have distributed shear vertical wall segment, ρt refers to horizontal reinforcement
reinforcement providing resistance in two orthogonal and ρl refers to vertical reinforcement.
directions in the plane of the wall. If hw /lw does not
exceed 2.0, reinforcement ratio ρl shall not be less The ratio hw /lw may refer to overall dimensions of a wall, or
than reinforcement ratio ρt . of a segment of the wall bounded by two openings, or an
opening and an edge. The intent of 21.9.4.2 is to make certain
21.9.4.4 — For all wall piers sharing a common that any segment of a wall is not assigned a unit strength
21 lateral force, Vn shall not be taken larger than larger than that for the entire wall. However, a wall segment
0.66Acv f c′ , where Acv is the gross area of concrete with a ratio of hw /lw higher than that of the entire wall should
bounded by web thickness and length of section. For be proportioned for the unit strength associated with the ratio
any one of the individual wall piers, Vn shall not be hw /lw based on the dimensions for that segment.
taken larger than 0.83Acw f c′ , where Acw is the area
of concrete section of the individual pier considered. To restrain the inclined cracks effectively, reinforcement
included in ρt and ρl should be appropriately distributed along
21.9.4.5 — For horizontal wall segments and the length and height of the wall (see 21.9.4.3). Chord
coupling beams, Vn shall not be taken larger than reinforcement provided near wall edges in concentrated
0.83Acw f c′ , where Acw is the area of concrete amounts for resisting bending moment is not to be included in
section of a horizontal wall segment or coupling beam. determining ρt and ρl. Within practical limits, shear reinforce-
ment distribution should be uniform and at a small spacing.
CODE COMMENTARY
additional requirement that the unit shear strength assigned
to any single pier does not exceed 0.83 f c′ . The upper
limit of strength to be assigned to any one member is
imposed to limit the degree of redistribution of shear force.
21.9.5 — Design for flexure and axial loads R21.9.5 — Design for flexure and axial loads
21.9.5.1 — Structural walls and portions of such walls R21.9.5.1 — Flexural strength of a wall or wall segment
subject to combined flexural and axial loads shall be is determined according to procedures commonly used for
designed in accordance with 10.2 and 10.3 except that columns. Strength should be determined considering the
10.3.6 and the nonlinear strain requirements of 10.2.2 applied axial and lateral forces. Reinforcement concentrated
shall not apply. Concrete and developed longitudinal in boundary elements and distributed in flanges and webs
reinforcement within effective flange widths, boundary should be included in the strength computations based on a
elements, and the wall web shall be considered strain compatibility analysis. The foundation supporting the
effective. The effects of openings shall be considered. wall should be designed to develop the wall boundary and
web forces. For walls with openings, the influence of the
opening or openings on flexural and shear strengths is to be
considered and a load path around the opening or openings
should be verified. Capacity-design concepts and strut-and-
tie models may be useful for this purpose.21.47
21.9.5.2 — Unless a more detailed analysis is R21.9.5.2 — Where wall sections intersect to form L-, T-, C-,
performed, effective flange widths of flanged sections or other cross-sectional shapes, the influence of the flange on
shall extend from the face of the web a distance equal the behavior of the wall should be considered by selecting
to the smaller of one-half the distance to an adjacent appropriate flange widths. Tests21.48 show that effective flange
wall web and 25 percent of the total wall height. width increases with increasing drift level and the effectiveness
of a flange in compression differs from that for a flange in
tension. The value used for the effective compression flange
width has little impact on the strength and deformation capacity
of the wall; therefore, to simplify design, a single value of
effective flange width based on an estimate of the effective 21
tension flange width is used in both tension and compression.
CODE COMMENTARY
21.9.6 — Boundary elements of special structural R21.9.6 — Boundary elements of special structural
walls walls
21.9.6.1 — The need for special boundary elements R21.9.6.1 — Two design approaches for evaluating
at the edges of structural walls shall be evaluated in detailing requirements at wall boundaries are included in
accordance with 21.9.6.2 or 21.9.6.3. The require- 21.9.6.1. Section 21.9.6.2 allows the use of displacement-
ments of 21.9.6.4 and 21.9.6.5 also shall be satisfied. based design of walls, in which the structural details are
determined directly on the basis of the expected lateral
displacements of the wall. The provisions of 21.9.6.3 are
similar to those of the 1995 Code, and have been retained
because they are conservative for assessing required transverse
reinforcement at wall boundaries for many walls. Require-
ments of 21.9.6.4 and 21.9.6.5 apply to structural walls
designed by either 21.9.6.2 or 21.9.6.3.
21.9.6.2 — This section applies to walls or wall piers R21.9.6.2 — Section 21.9.6.2 is based on the assumption
that are effectively continuous from the base of structure that inelastic response of the wall is dominated by flexural
to top of wall and designed to have a single critical action at a critical, yielding section. The wall should be
section for flexure and axial loads. Walls not satisfying proportioned so that the critical section occurs where intended.
these requirements shall be designed by 21.9.6.3.
Equation (21-8) follows from a displacement-based
(a) Compression zones shall be reinforced with approach.21.49,21.50 The approach assumes that special
special boundary elements where boundary elements are required to confine the concrete where
the strain at the extreme compression fiber of the wall
lw exceeds a critical value when the wall is displaced to the
c ≥ ------------------------------
- (21-8) design displacement. The horizontal dimension of the special
600 ( δ u /h w )
boundary element is intended to extend at least over the
length where the compression strain exceeds the critical
c in Eq. (21-8) corresponds to the largest neutral value. The height of the special boundary element is based on
axis depth calculated for the factored axial force and upper bound estimates of plastic hinge length and extends
nominal moment strength consistent with the design beyond the zone over which concrete spalling is likely to
displacement δu. Ratio δu /hw in Eq. (21-8) shall not occur. The lower limit of 0.007 on the quantity δu /hw requires
be taken less than 0.007; moderate wall deformation capacity for stiff buildings.
(b) Where special boundary elements are required
by 21.9.6.2(a), the special boundary element The neutral axis depth c in Eq. (21-8) is the depth calculated
reinforcement shall extend vertically from the critical according to 10.2, except the nonlinear strain requirements
section a distance not less than the larger of lw or of 10.2.2 need not apply, corresponding to development of
Mu /4Vu . nominal flexural strength of the wall when displaced in the
same direction as δu. The axial load is the factored axial
21 load that is consistent with the design load combination that
produces the design displacement δu.
21.9.6.3 — Structural walls not designed to the R21.9.6.3 — By this procedure, the wall is considered to
provisions of 21.9.6.2 shall have special boundary be acted on by gravity loads and the maximum shear and
elements at boundaries and edges around openings of moment induced by earthquake in a given direction. Under
structural walls where the maximum extreme fiber this loading, the compressed boundary at the critical section
compressive stress, corresponding to load combinations resists the tributary gravity load plus the compressive
including earthquake effects, E, exceeds 0.2fc′ . The resultant associated with the bending moment.
special boundary element shall be permitted to be
discontinued where the calculated compressive stress Recognizing that this loading condition may be repeated
is less than 0.15fc′ . Stresses shall be calculated for the many times during the strong motion, the concrete is to be
factored forces using a linearly elastic model and gross confined where the calculated compressive stresses exceed a
section properties. For walls with flanges, an effective nominal critical value equal to 0.2fc′ . The stress is to be
flange width as defined in 21.9.5.2 shall be used. calculated for the factored forces on the section assuming
linear response of the gross concrete section. The compressive
stress of 0.2fc′ is used as an index value and does not
CODE COMMENTARY
necessarily describe the actual state of stress that may
develop at the critical section under the influence of the
actual inertia forces for the anticipated earthquake intensity.
21.9.6.4 — Where special boundary elements are R21.9.6.4 — The value of c/2 in 21.9.6.4(a) is to provide
required by 21.9.6.2 or 21.9.6.3, (a) through (e) shall a minimum length of the special boundary element. Where
be satisfied: flanges are heavily stressed in compression, the web-to-
flange interface is likely to be heavily stressed and may
(a) The boundary element shall extend horizontally sustain local crushing failure unless special boundary
from the extreme compression fiber a distance not element reinforcement extends into the web. Equation (21-4)
less than the larger of c – 0.1lw and c/2, where c is does not apply to walls.
the largest neutral axis depth calculated for the
factored axial force and nominal moment strength Because horizontal reinforcement is likely to act as web
consistent with δu; reinforcement in walls requiring boundary elements, it
should be fully anchored in boundary elements that act as
(b) In flanged sections, the boundary element shall flanges (21.9.6.4). Achievement of this anchorage is difficult
include the effective flange width in compression when large transverse cracks occur in the boundary
and shall extend at least 300 mm into the web; elements. Therefore, standard 90-degree hooks or mechanical
(c) The boundary element transverse reinforcement anchorage schemes are recommended instead of straight bar
shall satisfy the requirements of 21.6.4.2 through development.
21.6.4.4, except Eq. (21-4) need not be satisfied and
the transverse reinforcement spacing limit of Tests21.51 show that adequate performance can be achieved
21.6.4.3(a) shall be one-third of the least dimension using spacing larger than permitted by 21.6.4.3(a).
of the boundary element;
21.9.6.5 — Where special boundary elements are R21.9.6.5 — Cyclic load reversals may lead to buckling
not required by 21.9.6.2 or 21.9.6.3, (a) and (b) shall of boundary longitudinal reinforcement even in cases where
21
be satisfied: the demands on the boundary of the wall do not require
special boundary elements. For walls with moderate
(a) If the longitudinal reinforcement ratio at the wall amounts of boundary longitudinal reinforcement, ties are
boundary is greater than 2.8/fy, boundary transverse required to inhibit buckling. The longitudinal reinforcement
reinforcement shall satisfy 21.6.4.2 and 21.9.6.4(a). ratio is intended to include only the reinforcement at the
The maximum longitudinal spacing of transverse rein- wall boundary as indicated in Fig. R21.9.6.5. A larger
forcement in the boundary shall not exceed 200 mm; spacing of ties relative to 21.9.6.4(c) is allowed due to the
lower deformation demands on the walls.
(b) Except when Vu in the plane of the wall is less than
0.083Acvλ f c′ , horizontal reinforcement terminating The addition of hooks or U-stirrups at the ends of horizontal
at the edges of structural walls without boundary wall reinforcement provides anchorage so that the reinforce-
elements shall have a standard hook engaging the ment will be effective in resisting shear forces. It will also tend
edge reinforcement or the edge reinforcement to inhibit the buckling of the vertical edge reinforcement. In
shall be enclosed in U-stirrups having the same walls with low in-plane shear, the development of horizontal
size and spacing as, and spliced to, the horizontal reinforcement is not necessary.
reinforcement.
CODE COMMENTARY
21.9.7.1 — Coupling beams with (ln /h) ≥ 4 shall Coupling beams connecting structural walls can provide
satisfy the requirements of 21.5. The provisions of stiffness and energy dissipation. In many cases, geometric
21.5.1.3 and 21.5.1.4 need not be satisfied if it can be limits result in coupling beams that are deep in relation to
shown by analysis that the beam has adequate lateral their clear span. Deep coupling beams may be controlled by
stability. shear and may be susceptible to strength and stiffness deterio-
ration under earthquake loading. Test results21.52,21.53 have
21.9.7.2 — Coupling beams with (ln /h) < 2 and with shown that confined diagonal reinforcement provides
Vu exceeding 0.33λ f c′ Acw shall be reinforced with adequate resistance in deep coupling beams.
two intersecting groups of diagonally placed bars
symmetrical about the midspan, unless it can be Experiments show that diagonally oriented reinforcement is
shown that loss of stiffness and strength of the effective only if the bars are placed with a large inclination.
coupling beams will not impair the vertical load- Therefore, diagonally reinforced coupling beams are
carrying ability of the structure, the egress from the restricted to beams having aspect ratio ln /h < 4. The 2008
structure, or the integrity of nonstructural components edition of this Code was changed to clarify that coupling
and their connections to the structure. beams of intermediate aspect ratio can be reinforced
21 according to 21.5.2 through 21.5.4.
21.9.7.3 — Coupling beams not governed by
21.9.7.1 or 21.9.7.2 shall be permitted to be reinforced Diagonal bars should be placed approximately symmetrically
either with two intersecting groups of diagonally in the beam cross section, in two or more layers. The
placed bars symmetrical about the midspan or diagonally placed bars are intended to provide the entire
according to 21.5.2 through 21.5.4. shear and corresponding moment strength of the beam;
designs deriving their moment strength from combinations
21.9.7.4 — Coupling beams reinforced with two of diagonal and longitudinal bars are not covered by these
intersecting groups of diagonally placed bars symmetrical provisions.
about the midspan shall satisfy (a), (b), and either (c)
or (d). Requirements of 11.7 shall not apply. Two confinement options are described. According to
21.9.7.4(c), each diagonal element consists of a cage of
(a) Vn shall be determined by longitudinal and transverse reinforcement as shown in
Fig. R21.9.7(a). Each cage contains at least four diagonal
Vn = 2Avd fysinα ≤ 10 f c′ Acw (21-9) bars and confines a concrete core. The requirement on side
dimensions of the cage and its core is to provide adequate
CODE COMMENTARY
21
Fig. R21.9.7—Coupling beams with diagonally oriented reinforcement. Wall boundary reinforcement shown on one side only
for clarity.
where α is the angle between the diagonal bars and toughness and stability to the cross section when the bars
the longitudinal axis of the coupling beam. are loaded beyond yielding. The minimum dimensions and
required reinforcement clearances may control the wall
(b) Each group of diagonal bars shall consist of a width. Revisions were made in the 2008 Code to relax
minimum of four bars provided in two or more layers. spacing of transverse reinforcement confining the diagonal
The diagonal bars shall be embedded into the wall bars, to clarify that confinement is required at the intersection
CODE COMMENTARY
not less than 1.25 times the development length for of the diagonals, and to simplify design of the longitudinal
fy in tension. and transverse reinforcement around the beam perimeter;
beams with these new details are expected to perform
(c) Each group of diagonal bars shall be enclosed by acceptably.
transverse reinforcement having out-to-out dimensions
not smaller than bw /2 in the direction parallel to bw Section 21.9.7.4(d) describes a second option for
and bw /5 along the other sides, where bw is the web confinement of the diagonals introduced in the 2008
width of the coupling beam. The transverse reinforce- Code (Fig. R21.9.7(b)). This second option is to confine the
ment shall satisfy 21.6.4.2 and 21.6.4.4, shall have entire beam cross section instead of confining the individual
spacing measured parallel to the diagonal bars diagonals. This option can considerably simplify field
satisfying 21.6.4.3(c) and not exceeding six times placement of hoops, which can otherwise be especially
the diameter of the diagonal bars, and shall have challenging where diagonal bars intersect each other or
spacing of crossties or legs of hoops measured enter the wall boundary.
perpendicular to the diagonal bars not exceeding
350 mm. For the purpose of computing Ag for use in When coupling beams are not used as part of the lateral-
Eq. (10-5) and (21-4), the concrete cover as required force-resisting system, the requirements for diagonal rein-
in 7.7 shall be assumed on all four sides of each group forcement may be waived.
of diagonal bars. The transverse reinforcement, or
its alternatively configured transverse reinforcement Test results21.53 demonstrate that beams reinforced as
satisfying the spacing and volume ratio requirements described in Section 21.9.7 have adequate ductility at shear
of the transverse reinforcement along the diagonals, forces exceeding 0.83 f c′ bwd. Consequently, the use of a
shall continue through the intersection of the diagonal limit of 0.83 f c′ Acw provides an acceptable upper limit.
bars. Additional longitudinal and transverse rein-
forcement shall be distributed around the beam
perimeter with total area in each direction not less
than 0.002bws and spacing not exceeding 300 mm.
21.10.1 — Scope
CODE COMMENTARY
21.10.2 — Special structural walls constructed using
precast concrete shall satisfy all requirements of 21.9
in addition to 21.4.2 and 21.4.3.
21.10.3 — Special structural walls constructed using R21.10.3 — Experimental and analytical studies21.54-21.56
precast concrete and unbonded post-tensioning have demonstrated that some types of precast structural
tendons and not satisfying the requirements of 21.10.2 walls post-tensioned with unbonded tendons, and not satis-
are permitted provided they satisfy the requirements of fying the prescriptive requirements of Chapter 21, provide
ACI ITG-5.1. satisfactory seismic performance characteristics. ACI ITG-5.1
defines a protocol for establishing a design procedure, vali-
dated by analysis and laboratory tests, for such walls, with
or without coupling beams.
21.11 — Structural diaphragms and trusses R21.11 — Structural diaphragms and trusses
Floor and roof slabs acting as structural diaphragms to Diaphragms as used in building construction are structural
transmit forces induced by earthquake ground motions elements (such as a floor or roof) that provide some or all of
in structures assigned to SDC D, E, or F shall be the following functions:
designed in accordance with this section. This section
also applies to collector elements and trusses forming (a) Support for building elements (such as walls, parti-
part of the seismic-force-resisting system. tions, and cladding) resisting horizontal forces but not
acting as part of the seismic-force-resisting system;
The earthquake design forces for structural In the general building codes, earthquake design forces for
diaphragms shall be obtained from the legally adopted floor and roof diaphragms typically are not computed directly
general building code using the applicable provisions during the lateral-force analysis that provides story forces and
and load combinations. story shears. Instead, diaphragm design forces at each level are
computed by a formula that amplifies the story forces recog-
nizing dynamic effects and includes minimum and maximum 21
limits. These forces are used with the governing load combi-
nations to design diaphragms for shear and moment.
CODE COMMENTARY
forces and deformations. It is preferable for inelastic
behavior to occur only in the intended locations of the
vertical earthquake-force-resisting system that are detailed
for ductile response, such as in the beam plastic hinges of
special moment frames, or in flexural plastic hinging at the
base of structural walls or in coupling beams. For buildings
without long diaphragm spans between lateral-force-
resisting elements, elastic diaphragm behavior is typically
not difficult to achieve. For buildings where diaphragms
could reach their flexural or shear strength before yielding
occurs in the vertical seismic systems, designers should
consider providing increased diaphragm strength.
21
CODE COMMENTARY
21.11.4 — Cast-in-place composite-topping slab R21.11.4 — Cast-in-place composite-topping slab
diaphragms diaphragms
A composite-topping slab cast in place on a precast A bonded topping slab is required so that the floor or roof
floor or roof shall be permitted to be used as a structural system can provide restraint against slab buckling. Reinforce-
diaphragm, provided the topping slab is reinforced and ment is required to ensure the continuity of the shear
the surface of the previously hardened concrete on transfer across precast joints. The connection requirements
which the topping slab is placed is clean, free of are introduced to promote a complete system with necessary
laitance, and intentionally roughened. shear transfers.
21.11.5 — Cast-in-place topping slab diaphragms R21.11.5 — Cast-in-place topping slab diaphragms
A cast-in-place noncomposite topping on a precast Composite action between the topping slab and the precast
floor or roof shall be permitted to serve as a structural floor elements is not required, provided that the topping slab
diaphragm, provided the cast-in-place topping acting is designed to resist the design seismic forces.
alone is proportioned and detailed to resist the design
earthquake forces.
Concrete slabs and composite topping slabs serving as The minimum thickness of concrete diaphragms reflects
structural diaphragms used to transmit earthquake forces current practice in joist and waffle systems and composite
shall not be less than 50 mm thick. Topping slabs placed topping slabs on precast floor and roof systems. Thicker
over precast floor or roof elements, acting as structural slabs are required when the topping slab does not act
diaphragms and not relying on composite action with compositely with the precast system to resist the design
the precast elements to resist the design earthquake seismic forces.
forces, shall have thickness not less than 65 mm.
21.11.7.1 — The minimum reinforcement ratio for R21.11.7.1 — Minimum reinforcement ratios for
structural diaphragms shall be in conformance with diaphragms correspond to the required amount of temperature
7.12. Except for post-tensioned slabs, reinforcement and shrinkage reinforcement (7.12). The maximum spacing
spacing each way in floor or roof systems shall not for web reinforcement is intended to control the width of
exceed 450 mm. Where welded wire reinforcement is inclined cracks. Minimum average prestress requirements
used as the distributed reinforcement to resist shear in (7.12.3) are considered to be adequate to limit the crack
topping slabs placed over precast floor and roof widths in post-tensioned floor systems; therefore, the
elements, the wires parallel to the span of the precast maximum spacing requirements do not apply to these systems.
elements shall be spaced not less than 250 mm on
center. Reinforcement provided for shear strength The minimum spacing requirement for welded wire reinforce- 21
shall be continuous and shall be distributed uniformly ment in topping slabs on precast floor systems (see 21.11.7.1)
across the shear plane. is to avoid fracture of the distributed reinforcement during
an earthquake. Cracks in the topping slab open immediately
above the boundary between the flanges of adjacent precast
members, and the wires crossing those cracks are restrained
by the transverse wires.21.58 Therefore, all the deformation
associated with cracking should be accommodated in a
distance not greater than the spacing of the transverse wires.
A minimum spacing of 250 mm for the transverse wires is
required in 21.11.7.1 to reduce the likelihood of fracture of
the wires crossing the critical cracks during a design earth-
quake. The minimum spacing requirements do not apply to
diaphragms reinforced with individual bars, because strains
are distributed over a longer length.
CODE COMMENTARY
21.11.7.2 — Bonded tendons used as reinforcement
to resist collector forces or diaphragm shear or flexural
tension shall be proportioned such that the stress due
to design earthquake forces does not exceed 420 MPa.
Precompression from unbonded tendons shall be
permitted to resist diaphragm design forces if a
seismic load path is provided.
21.11.7.3 — All reinforcement used to resist R21.11.7.3 — Bar development and lap splices are
collector forces, diaphragm shear, or flexural tension designed according to requirements of Chapter 12 for
shall be developed or spliced for fy in tension. reinforcement in tension. Reductions in development or
splice length for calculated stresses less than fy are not
permitted, as indicated in 12.2.5.
21.11.7.5 — Collector elements with compressive R21.11.7.5 — In documents such as the NEHRP provi-
stresses exceeding 0.2fc′ at any section shall have sions,21.4 ASCE/SEI 7,21.1 the International Building
transverse reinforcement satisfying 21.9.6.4(c) over Code,21.2 and the Uniform Building Code,21.3 collector
the length of the element. The specified transverse elements of diaphragms are designed for forces amplified
reinforcement is permitted to be discontinued at a by a factor, Ωo, to account for the overstrength in the
section where the calculated compressive stress is vertical elements of the seismic-force-resisting systems.
less than 0.15fc′ . The amplification factor Ωo ranges between 2 and 3 for
most concrete structures, depending on the document
Where design forces have been amplified to account selected and on the type of seismic system. In some docu-
for the overstrength of the vertical elements of the ments, the factor can be calculated based on the maximum
seismic-force-resisting system, the limit of 0.2fc′ shall forces that can be developed by the elements of the vertical
be increased to 0.5fc′ , and the limit of 0.15fc′ shall be seismic-force-resisting system.
increased to 0.4fc′ .
Compressive stress calculated for the factored forces on a
linearly elastic model based on gross section of the structural
diaphragm is used as an index value to determine whether
confining reinforcement is required. A calculated compressive
stress of 0.2fc′ in a member, or 0.5fc′ for forces amplified by
Ωo, is assumed to indicate that integrity of the entire
structure depends on the ability of that member to resist
21 substantial compressive force under severe cyclic loading.
Therefore, transverse reinforcement is required in such
members to provide confinement for the concrete and the
reinforcement.
21.11.7.6 — Longitudinal reinforcement for collector R21.11.7.6 — Section 21.11.7.6 is intended to reduce
elements at splices and anchorage zones shall have the possibility of bar buckling and provide adequate bar
either: development conditions in the vicinity of splices and
anchorage zones.
(a) A minimum center-to-center spacing of three
longitudinal bar diameters, but not less than 40 mm,
and a minimum concrete clear cover of two and
one-half longitudinal bar diameters, but not less than
50 mm; or
CODE COMMENTARY
21.11.8 — Flexural strength R21.11.8 — Flexural strength
Diaphragms and portions of diaphragms shall be Flexural strength for diaphragms is calculated using the
designed for flexure in accordance with 10.2 and 10.3 same assumptions as for walls, columns, or beams. The
except that the nonlinear distribution of strain require- design of diaphragms for flexure and other actions uses the
ments of 10.2.2 for deep beams need not apply. The applicable load combinations of 9.2 to consider earthquake
effects of openings shall be considered. forces acting concurrently with gravity or other loads.
21.11.9.1 — Vn of structural diaphragms shall not The shear strength requirements for diaphragms are similar
exceed to those for slender structural walls and are based on the
shear provisions for beams. The term Acv refers to the gross
Vn = Acv (0.17λ f c′ + ρt fy) (21-10) area of the diaphragm, but may not exceed the thickness
times the width of the diaphragm. This corresponds to the
gross area of the effective deep beam that forms the
For cast-in-place topping slab diaphragms on precast diaphragm. Distributed slab reinforcement, ρt , used to
floor or roof members, Acv shall be computed using calculate shear strength of a diaphragm in Eq. (21-10) is
the thickness of topping slab only for noncomposite positioned perpendicular to the diaphragm flexural reinforce-
topping slab diaphragms and the combined thickness ment. Section 21.11.9.2 limits the maximum shear strength
of cast-in-place and precast elements for composite of the diaphragm.
topping slab diaphragms. For composite topping slab 21
diaphragms, the value of fc′ used to determine Vn In addition to satisfying the provisions in 21.11.9.1 and
shall not exceed the smaller of fc′ for the precast 21.11.9.2, cast-in-place topping slab diaphragms must also
members and fc′ for the topping slab. satisfy 21.11.9.3 and 21.11.9.4. Cast-in-place topping slabs
on a precast floor or roof system tend to have shrinkage
21.11.9.2 — Vn of structural diaphragms shall not cracks that are aligned with the joints between adjacent
exceed 0.66Acv f c′ . precast members. Therefore, the additional shear strength
requirements for topping slab diaphragms in 21.11.9.3 are
21.11.9.3 — Above joints between precast elements based on a shear friction model,21.58 and the assumed crack
in noncomposite and composite cast-in-place topping plane corresponds to joints in the precast system along the
slab diaphragms, Vn shall not exceed direction of the applied shear, as shown in Fig. R11.6.4. The
coefficient of friction, μ, in the shear friction model is taken
Vn = Avf fyμ (21-11) equal to 1.0 for normalweight concrete due to the presence
of these shrinkage cracks.
where Avf is total area of shear friction reinforcement
within topping slab, including both distributed and Both distributed and boundary reinforcement in the topping
boundary reinforcement, that is oriented perpendicular slab may be considered as shear friction reinforcement, Avf.
CODE COMMENTARY
to joints in the precast system and coefficient of friction, Boundary reinforcement within the diaphragm was called
μ, is 1.0λ, where λ is given in 11.6.4.3. At least one- chord reinforcement in ACI 318 before 2008. Although the
half of Avf shall be uniformly distributed along the boundary reinforcement also resists flexural forces in the
length of the potential shear plane. Area of distributed diaphragm, the reduction in the shear friction resistance in
reinforcement in topping slab shall satisfy 7.12.2.1 in the tension zone is offset by the increase in shear friction
each direction. resistance in the compression zone. Therefore, the area of
boundary reinforcement used to resist shear friction need
21.11.9.4 — Above joints between precast elements not be added to the area of boundary reinforcement used to
in noncomposite and composite cast-in-place topping resist flexural forces. The distributed topping slab reinforce-
slab diaphragms, Vn shall not exceed the limits in ment must contribute at least half of the nominal shear
11.6.5 where Ac is computed using the thickness of strength. It is assumed that connections between the precast
the topping slab only. elements do not contribute to the shear strength of the
topping slab diaphragm.
21 21.12.1.1 — Foundations resisting earthquake- Requirements for foundations supporting buildings assigned
induced forces or transferring earthquake-induced to SDC D, E, or F were added to the 1999 Code. They
forces between structure and ground in structures represent a consensus of a minimum level of good practice
assigned to SDC D, E, or F shall comply with 21.12 in designing and detailing concrete foundations including
and other applicable Code provisions. piles, drilled piers, and caissons. It is desirable that inelastic
response in strong ground shaking occurs above the founda-
21.12.1.2 — The provisions in this section for piles, tions, as repairs to foundations can be extremely difficult
drilled piers, caissons, and slabs-on-ground shall and expensive.
supplement other applicable Code design and
construction criteria. See 1.1.6 and 1.1.7.
21.12.2 — Footings, foundation mats, and pile caps R21.12.2 — Footings, foundation mats, and pile caps
CODE COMMENTARY
21.12.2.2 — Columns designed assuming fixed-end R21.12.2.2 — Tests21.59 have demonstrated that flexural
conditions at the foundation shall comply with 21.12.2.1 members terminating in a footing, slab, or beam (a T-joint)
and, if hooks are required, longitudinal reinforcement should have their hooks turned inward toward the axis of the
resisting flexure shall have 90-degree hooks near the member for the joint to be able to resist the flexure in the
bottom of the foundation with the free end of the bars member forming the stem of the T.
oriented toward the center of the column.
21.12.2.4 — Where earthquake effects create uplift R21.12.2.4 — The purpose of 21.12.2.4 is to emphasize
forces in boundary elements of special structural walls that top reinforcement should be provided as well as other
or columns, flexural reinforcement shall be provided in required reinforcement.
the top of the footing, mat, or pile cap to resist actions
resulting from the design load combinations, and shall
not be less than required by 10.5.
21.12.2.5 — See 22.10 for use of structural plain R21.12.2.5 — Committee 318 recommends that foundation
concrete in footings and basement walls. or basement walls be reinforced in buildings assigned to
SDC D, E, or F.
21.12.3 — Grade beams and slabs-on-ground R21.12.3 — Grade beams and slabs-on-ground
21.12.3.1 — Grade beams designed to act as For seismic conditions, slabs-on-ground (soil-supported
horizontal ties between pile caps or footings shall have slabs) are often part of the lateral-force-resisting system and
continuous longitudinal reinforcement that shall be should be designed in accordance with this Code as well as
developed within or beyond the supported column or other appropriate standards or guidelines. See 1.1.7.
anchored within the pile cap or footing at all discontinuities.
21.12.3.2 — Grade beams designed to act as hori- R21.12.3.2 — Grade beams between pile caps or footings
zontal ties between pile caps or footings shall be propor- can be separate beams beneath the slab-on-ground or can be
tioned such that the smallest cross-sectional dimension a thickened portion of the slab-on-ground. The cross-
shall be equal to or greater than the clear spacing sectional limitation and minimum tie requirements provide
between connected columns divided by 20, but need not reasonable proportions. 21
be greater than 450 mm. Closed ties shall be provided at
a spacing not to exceed the lesser of one-half the smallest
orthogonal cross-sectional dimension and 300 mm.
21.12.3.3 — Grade beams and beams that are part R21.12.3.3 — Grade beams resisting seismic flexural
of a mat foundation subjected to flexure from columns stresses from column moments should have reinforcement
that are part of the seismic-force-resisting system shall details similar to the beams of the frame above the foundation.
conform to 21.5.
21.12.3.4 — Slabs-on-ground that resist seismic R21.12.3.4 — Slabs-on-ground often act as a diaphragm to
forces from walls or columns that are part of the hold the building together at the ground level and minimize the
seismic-force-resisting system shall be designed as effects of out-of-phase ground motion that may occur over the
structural diaphragms in accordance with 21.11. The footprint of the building. In these cases, the slab-on-ground
design drawings shall clearly state that the slab-on- should be adequately reinforced and detailed. The design
ground is a structural diaphragm and part of the drawings should clearly state that these slabs-on-ground are
seismic-force-resisting system. structural members so as to prohibit sawcutting of the slab.
CODE COMMENTARY
21.12.4 — Piles, piers, and caissons R21.12.4 — Piles, piers, and caissons
21.12.4.1 — Provisions of 21.12.4 shall apply to Adequate performance of piles and caissons for seismic
concrete piles, piers, and caissons supporting structures loadings requires that these provisions be met in addition to
designed for earthquake resistance. other applicable standards or guidelines. See R1.1.6.
21.12.4.2 — Piles, piers, or caissons resisting R21.12.4.2 — A load path is necessary at pile caps to
tension loads shall have continuous longitudinal transfer tension forces from the reinforcing bars in the
reinforcement over the length resisting design tension column or boundary member through the pile cap to the
forces. The longitudinal reinforcement shall be detailed reinforcement of the pile or caisson.
to transfer tension forces within the pile cap to
supported structural members.
21.12.4.3 — Where tension forces induced by earth- R21.12.4.3 — Grouted dowels in a blockout in the top of
quake effects are transferred between pile cap or mat a precast concrete pile need to be developed, and testing is a
foundation and precast pile by reinforcing bars grouted practical means of demonstrating strength. Alternatively,
or post-installed in the top of the pile, the grouting reinforcing bars can be cast in the upper portion of the pile,
system shall have been demonstrated by test to exposed by chipping of concrete and mechanically spliced
develop at least 1.25fy of the bar. or welded to an extension.
21.12.4.4 — Piles, piers, or caissons shall have R21.12.4.4 — During earthquakes, piles can be subjected
transverse reinforcement in accordance with 21.6.4.2 to extremely high flexural demands at points of discontinuity,
through 21.6.4.4 at locations (a) and (b): especially just below the pile cap and near the base of a soft
or loose soil deposit. The Code requirement for confinement
(a) At the top of the member for at least 5 times the reinforcement at the top of the pile is based on numerous
member cross-sectional dimension, but not less failures observed at this location in earthquakes. Transverse
than 1.8 m below the bottom of the pile cap; reinforcement is required in this region to provide ductile
performance. Possible inelastic action in the pile at abrupt
(b) For the portion of piles in soil that is not capable changes in soil deposits should also be considered, such as
of providing lateral support, or in air and water, along changes from soft to firm or loose to dense soil layers.
the entire unsupported length plus the length Where precast piles are to be used, the potential for the pile
required in 21.12.4.4(a). tip to be driven to an elevation different than that specified
in the drawings needs to be considered when detailing the
pile. If the pile reaches refusal at a shallower depth, a longer
length of pile will need to be cut off. If this possibility is not
foreseen, the length of transverse reinforcement required by
21.12.4.4 may not be available after the excess pile length is
cut off.
21.12.4.7 — Pile caps incorporating batter piles R21.12.4.7 — Extensive structural damage has often been
shall be designed to resist the full compressive observed at the junction of batter piles and the buildings. The
strength of the batter piles acting as short columns. pile cap and surrounding structure should be designed for
The slenderness effects of batter piles shall be consid- the potentially large forces that can be developed in batter
ered for the portion of the piles in soil that is not piles.
capable of providing lateral support, or in air or water.
CODE COMMENTARY
21.13 — Members not designated as part of R21.13 — Members not designated as part of
the seismic-force-resisting system the seismic-force-resisting system
CODE COMMENTARY
21.13.4.1 — Materials shall satisfy 21.1.4.2,
21.1.4.3, 21.1.5.2, 21.1.5.4, and 21.1.5.5. Mechanical
splices shall satisfy 21.1.6 and welded splices shall
satisfy 21.1.7.1.
21.13.5 — Precast concrete frame members assumed R21.13.5 — Damage to some buildings with precast
not to contribute to lateral resistance, including their concrete gravity systems during the 1994 Northridge earth-
connections, shall satisfy (a), (b), and (c), in addition to quake was attributed to several factors addressed in 21.13.5.
21.13.2 through 21.13.4: Columns should contain ties over their entire height, frame
members not proportioned to resist earthquake forces
(a) Ties specified in 21.13.3.2 shall be provided over should be tied together, and longer bearing lengths should
the entire column height, including the depth of the be used to maintain integrity of the gravity system during
beams; shaking. The 50 mm increase in bearing length is based on
an assumed 4 percent story drift ratio and 1.3 m beam depth,
(b) Structural integrity reinforcement, as specified in and is considered to be conservative for the ground motions
16.5, shall be provided; and expected for structures assigned to SDC D, E, or F. In addition
(c) Bearing length at support of a beam shall be at to the provisions of 21.13.5, precast frame members
least 50 mm longer than determined from calcula- assumed not to contribute to lateral resistance should also
tions using bearing strength values from 10.14. satisfy 21.13.2 through 21.13.4, as applicable.
21.13.6 — For slab-column connections of two-way R21.13.6 — Provisions for shear reinforcement at slab-
slabs without beams, slab shear reinforcement satis- column connections were added in 2005 to reduce the
fying the requirements of 11.11.3 and 11.11.5 and likelihood of slab punching shear failure. The shear reinforce-
providing Vs not less than 0.29 f c′ bod shall extend at ment is required unless either 21.13.6(a) or (b) is satisfied.
least four times the slab thickness from the face of the
support, unless either (a) or (b) is satisfied: Section 21.13.6(a) requires calculation of shear stress due to
the factored shear force and induced moment according to
(a) The requirements of 11.11.7 using the design 11.11.7.2. The induced moment is the moment that is
shear Vug and the induced moment transferred calculated to occur at the slab-column connection when
between the slab and column under the design subjected to the design displacement. Section 13.5.1.2 and
21 displacement; the accompanying Commentary provide guidance on
selection of the stiffness of the slab-column connection for
(b) The design story drift ratio does not exceed the the purpose of this calculation.
larger of 0.005 and [0.035 – 0.05(Vug /φVc)].
Design story drift ratio shall be taken as the larger of Section 21.13.6(b) does not require the calculation of induced
the design story drift ratios of the adjacent stories moments, and is based on research21.60,21.61 that identifies
above and below the slab-column connection. Vc is the likelihood of punching shear failure considering the story
defined in 11.11.2. Vug is the factored shear force on drift ratio and shear due to gravity loads. Figure R21.13.6
the slab critical section for two-way action, calculated illustrates the requirement. The requirement can be satisfied
for the load combination 1.2D + 1.0L + 0.2S. by adding slab shear reinforcement, increasing slab thickness,
changing the design to reduce the design story drift ratio, or a
The load factor on the live load, L, shall be permitted combination of these.
to be reduced to 0.5 except for garages, areas occupied
as places of public assembly, and all areas where L is If column capitals, drop panels, shear caps, or other changes in
greater than 4.8 kN/m2. slab thickness are used, the requirements of 21.13.6 are evalu-
ated at all potential critical sections, as required by 11.11.1.2.
CODE COMMENTARY
21
21
CODE COMMENTARY
22.1 — Scope R22.1 — Scope
22.1.1 — This chapter provides minimum requirements Before the 1995 Code, requirements for plain concrete were
for design and construction of structural plain concrete set forth in “Building Code Requirements for Structural
members (cast-in-place or precast). Plain Concrete (ACI 318.1-89) (Revised 1992).” Require-
ments for plain concrete are now in this Code (see 2.2 for
definition of plain concrete). Limitations are provided in
22.1.2 to clarify the scope and applicability of this chapter.
See 1.1.4 for requirements for residential construction
within the scope of ACI 332.
22.1.2 — Unless in conflict with the provisions of R22.1.2 — Sections of the Code do not apply to the design of
Chapter 22, the following provisions of this Code shall structural plain concrete for the following specific reasons:
apply to structural plain concrete members: Sections
1.1 through 7.5, 7.6.1, 7.6.2, 7.6.4, 7.7, 9.1.3, 9.2, 9.3.5, Sections 7.6 and 7.8 through 7.13 — These sections
Chapter 20, 21.12.2.5, C.9.2, C.9.3.5, and Appendix D. contain requirements intended for reinforced concrete
members and, with the exception of 7.6.1, 7.6.2, and 7.6.4,
are not applicable to structural plain concrete members, for
which strength is determined only by member size and
concrete strength, and not by reinforcement (see 22.5).
Concrete cover requirements of 7.7 apply to structural plain
concrete members if reinforcement is provided.
CODE COMMENTARY
22.2 — Limitations R22.2 — Limitations
22.2.1 — Use of structural plain concrete shall be R22.2.1 and R22.2.2 — Because the strength and structural
limited to (a), (b), or (c): integrity of structural plain concrete members is based
solely on the member size, concrete strength, and other
(a) Members that are continuously supported by soil concrete properties, use of structural plain concrete should
or supported by other structural members capable of be limited to members that are primarily in a state of
providing continuous vertical support; compression, members that can tolerate random cracks
without detriment to their structural integrity, and members
(b) Members for which arch action provides where ductility is not an essential feature of design. The
compression under all conditions of loading; tensile strength of concrete can be used in design of struc-
(c) Walls and pedestals. See 22.6 and 22.8. tural plain concrete members. Tensile stresses due to restraint
from creep, shrinkage, or temperature effects are to be
The use of structural plain concrete columns shall not considered to avoid uncontrolled cracks or structural failure.
be permitted.
Plain concrete walls are permitted (see 22.6) without a height
22.2.2 — This chapter shall not govern design and limitation. However, for multistory construction and other
installation of cast-in-place concrete piles and piers major structures, ACI Committee 318 encourages the use of
embedded in ground. walls designed in accordance with Chapter 14 (see R22.6).
Specified compressive strength of structural plain A minimum specified compressive strength requirement for
concrete shall not be less than the larger of that given structural plain concrete construction is considered necessary
in 1.1.1 and that required for durability in Chapter 4. because performance and safety is based solely on strength
and quality of concrete treated as a homogeneous material.
Lean concrete mixtures may not produce adequately
22 homogeneous material or well-formed surfaces.
22.3.1 — Contraction or isolation joints shall be Joints in plain concrete construction are an important design
provided to divide structural plain concrete members consideration. In reinforced concrete, reinforcement is
into flexurally discontinuous elements. The size of provided to resist the stresses due to restraint of creep,
each element shall be chosen to limit stress caused by shrinkage, and temperature effects. In plain concrete, joints
restraint to movements from creep, shrinkage, and are the only means of controlling and, thereby, relieving the
temperature effects. buildup of such tensile stresses. A plain concrete member
should therefore be small enough, or divided into smaller
22.3.2 — In determining the number and location of elements by joints, to control the buildup of internal
contraction or isolation joints, consideration shall be stresses. The joint may be a contraction joint or an isolation
given to: influence of climatic conditions; selection and joint. A minimum 25 percent reduction of member thickness is
CODE COMMENTARY
proportioning of materials; mixing, placing, and curing considered sufficient for contraction joints to be effective.
of concrete; degree of restraint to movement; stresses The jointing should be such that no axial tension or flexural
due to loads to which an element is subject; and tension can be developed across a joint after cracking, if
construction techniques. applicable—a condition referred to as flexural discontinuity.
Where random cracking due to creep, shrinkage, and
temperature effects will not affect the structural integrity,
and is otherwise acceptable, such as transverse cracks in a
continuous wall footing, transverse contraction, or isolation
joints are not necessary.
22.4.1 — Factored loads and forces shall be in combi- Plain concrete members are proportioned for adequate
nations as in 9.2. strength using factored loads and forces. When the design
strength is exceeded, the section should be increased or the
22.4.2 — Where required strength exceeds design specified strength of concrete increased, or both, or the
strength, reinforcement shall be provided and the member designed as a reinforced concrete member in
member designed as a reinforced concrete member in accordance with the Code. An increase in concrete section
accordance with appropriate design requirements of may have a detrimental effect; stress due to load will
this Code. decrease but stresses due to creep, shrinkage, and temperature
effects may increase.
22.4.3 — Strength design of structural plain concrete R22.4.3 — Flexural tension may be considered in design of
members for flexure and axial loads shall be based on plain concrete members to sustain loads, provided the
a linear stress-strain relationship in both tension and computed stress does not exceed the permissible stress, and
compression. construction, contraction, or isolation joints are provided to
relieve the resulting tensile stresses due to restraint of creep,
temperature, and shrinkage effects.
φMn ≥ Mu (22-1)
CODE COMMENTARY
where
Mn = 0.42λ f c′ Sm (22-2)
Mn = 0.85fc′ Sm (22-3)
22.5.2 — Design of cross sections subject to R22.5.2 — Equation (22-5) is presented to reflect the
compression shall be based on general range of braced and restrained end conditions
encountered in structural plain concrete elements. The
φPn ≥ Pu (22-4) effective length factor was omitted as a modifier of lc, the
vertical distance between supports, because this is conservative
where Pn is computed by for walls with assumed pin supports that are required to be
braced against lateral translation as in 22.6.6.4.
lc ⎞ 2
P n = 0.60f c′ 1 – ⎛ --------- A1 (22-5)
⎝ 32h-⎠
22.5.3 — Members subject to combined flexure and R22.5.3 — Plain concrete members subject to combined
axial load in compression shall be proportioned such flexure and axial compressive load are proportioned such
that on the compression face: that on the compression face
22.5.4 — Design of rectangular cross sections subject R22.5.4 — Proportions of plain concrete members usually
to shear shall be based on are controlled by tensile strength rather than shear strength.
22 Shear stress (as a substitute for principal tensile stress)
φVn ≥ Vu (22-8) rarely will control. However, because it is difficult to
foresee all possible conditions where shear may have to be
where Vn is computed by investigated (such as shear keys), Committee 318 maintains
the investigation of this basic stress condition.
Vn = 0.11λ f c′ bwh (22-9)
The shear requirements for plain concrete assume an
uncracked section. Shear failure in plain concrete will be a
for beam action and by diagonal tension failure, occurring when the principal
tensile stress near the centroidal axis becomes equal to the
2 tensile strength of the concrete. Since the major portion of
Vn = 0.11 1 + --- λ f c′ b o h (22-10)
β the principal tensile stress comes from the shear, the Code
safeguards against tensile failure by limiting the permissible
shear at the centroidal axis as calculated from the equation
for two-way action, but not greater than 0.22λ f c′ boh.
for a section of homogeneous material:
CODE COMMENTARY
In Eq. (22-10), β corresponds to ratio of long side to v = VQ/Ib
short side of concentrated load or reaction area.
where v and V are the shear stress and shear force, respec-
tively, at the section considered; Q is the statical moment of
the area outside the section being considered about centroidal
axis of the gross section; I is the moment of inertia of the
gross section; and b is the width where shear stress is being
computed.
φBn ≥ Bu (22-11)
Bn = 0.85fc′ A1 (22-12)
22.6.1 — Structural plain concrete walls shall be Plain concrete walls are commonly used for basement wall
continuously supported by soil, footings, foundation construction for residential and light commercial buildings
walls, grade beams, or other structural members in low or nonseismic areas. Although the Code imposes no
capable of providing continuous vertical support. absolute maximum height limitation on the use of plain
concrete walls, experience with use of plain concrete in
22.6.2 — Structural plain concrete walls shall be relatively minor structures should not be extrapolated to
designed for vertical, lateral, and other loads to which using plain concrete walls in multistory construction and
they are subjected. other major structures where differential settlement, wind,
earthquake, or other unforeseen loading conditions require
22.6.3 — Structural plain concrete walls shall be the walls to possess some ductility and ability to maintain 22
designed for an eccentricity corresponding to the their integrity when cracked. For such conditions, ACI
maximum moment that can accompany the axial load Committee 318 strongly encourages the use of walls
but not less than 0.10h. If the resultant of all factored designed in accordance with Chapter 14.
loads is located within the middle third of the overall
wall thickness, the design shall be in accordance with The provisions for plain concrete walls are applicable only
22.5.3 or 22.6.5. Otherwise, walls shall be designed in for walls laterally supported in such a manner as to prohibit
accordance with 22.5.3. relative lateral displacement at top and bottom of individual
wall elements (see 22.6.6.4). The Code does not cover walls
22.6.4 — Design for shear shall be in accordance with without horizontal support to prohibit relative displacement
22.5.4. at top and bottom of wall elements. Such laterally unsup-
ported walls are to be designed as reinforced concrete
members in accordance with the Code.
CODE COMMENTARY
22.6.5 — Empirical design method R22.6.5 — Empirical design method
22.6.5.1 — Structural plain concrete walls of solid When the resultant load falls within the middle-third of the
rectangular cross section shall be permitted to be wall thickness (kern of wall section), plain concrete walls
designed by Eq. (22-13) if the resultant of all factored may be designed using the simplified Eq. (22-14). Eccentric
loads is located within the middle-third of the overall loads and lateral forces are used to determine the total
thickness of wall. eccentricity of the factored axial force Pu. If the eccentricity
does not exceed h/6, Eq. (22-14) may be applied, and design
22.6.5.2 — Design of walls subject to axial loads in performed considering Pu as a concentric load. The factored
compression shall be based on axial load Pu should not exceed the design axial strength
φPn. Equation (22-14) reflects the range of braced and
φPn ≥ Pu (22-13) restrained end conditions encountered in wall design. The
limitations of 22.6.6 apply whether the wall is proportioned
where Pu is factored axial force and Pn is nominal by 22.5.3 or by the empirical method of 22.6.5.
axial strength calculated by
lc ⎞ 2
P n = 0.45f c′ A g 1 – ⎛ --------- (22-14)
⎝ 32h-⎠
22.6.6 — Limitations
CODE COMMENTARY
22.7.3 — Plain concrete shall not be used for footings
on piles.
22.7.4 — Thickness of structural plain concrete footings R22.7.4 — Thickness of plain concrete footings will be
shall be not less than 200 mm. See 22.4.7. controlled by flexural strength (extreme fiber stress in
tension not greater than 0.42φλ f c′ ) rather than shear
strength for the usual proportions of plain concrete footings.
Shear rarely will control (see R22.5.4). For footings cast
against soil, overall thickness h used for strength computa-
tions is specified in 22.4.7.
CODE COMMENTARY
22.7.8 — Factored bearing load, Bu , on concrete at
contact surface between supporting and supported
member shall not exceed design bearing strength,
φBn , for either surface as given in 22.5.5.
22.8.1 — Plain concrete pedestals shall be designed The height-thickness limitation for plain concrete pedestals
for vertical, lateral, and other loads to which they are does not apply for portions of pedestals embedded in soil
subjected. capable of providing lateral restraint.
22.9.1 — Design of precast plain concrete members Precast structural plain concrete members are subject to all
shall consider all loading conditions from initial fabrication limitations and provisions for cast-in-place concrete
to completion of the structure, including form removal, contained in this chapter.
storage, transportation, and erection.
The approach to contraction or isolation joints is expected to
22.9.2 — Limitations of 22.2 apply to precast members be somewhat different than for cast-in-place concrete since
of plain concrete not only to the final condition but also the major portion of shrinkage stresses takes place prior to
during fabrication, transportation, and erection. erection. To ensure stability, precast members should be
connected to other members. The connection should
22.9.3 — Precast members shall be connected transfer no tension.
securely to transfer all lateral forces into a structural
system capable of resisting such forces.
CODE COMMENTARY
reinforced masonry walls are permitted provided the
footings are reinforced longitudinally with not less
than two continuous reinforcing bars. Bars shall not
be smaller than No. 13 and shall have a total area of
not less than 0.002 times the gross cross-sectional
area of the footing. Continuity of reinforcement shall
be provided at corners and intersections;
22
22
CODE COMMENTARY
A.1 — Definitions RA.1 — Definitions
B-region — A portion of a member in which the plane B-region — In general, any portion of a member outside of
sections assumption of flexure theory from 10.2.2 can a D-region is a B-region.
be applied.
CODE COMMENTARY
D-region — The portion of a member within a distance, D-region — The shaded regions in Fig. RA.1.1(a) and (b)
h, from a force discontinuity or a geometric discontinuity. show typical D-regions.A.1 The plane sections assumption
of 10.2.2 is not applicable in such regions.
CODE COMMENTARY
containing B-regions—the usual case in beam design—are
designed for shear using the traditional shear design
procedures from 11.1 through 11.4 ignoring D-regions.
Deep beam — See 10.7.1 and 11.7.1. Deep beam — See Fig. RA.1.2(a), RA.1.2(b), and RA.1.3,
and Sections 10.7 and 11.7.
Nodal zone — The volume of concrete around a node Nodal zone — Historically, hydrostatic nodal zones as shown
that is assumed to transfer strut-and-tie forces through in Fig. RA.1.4 were used. These were largely superseded by
the node. what are called extended nodal zones, shown in Fig. RA.1.5.
CODE COMMENTARY
CODE COMMENTARY
In the nodal zone shown in Fig. RA.1.6(a), the reaction R
equilibrates the vertical components of the forces C1 and
C2. Frequently, calculations are easier if the reaction R is
divided into R1, which equilibrates the vertical component
of C1 and R2, which equilibrates the vertical component of
the force C2, as shown in Fig. RA1.6(b).
CODE COMMENTARY
Node — The point in a joint in a strut-and-tie model Node — For equilibrium, at least three forces should act on a
where the axes of the struts, ties, and concentrated node in a strut-and-tie model, as shown in Fig. RA.1.7. Nodes
forces acting on the joint intersect. are classified according to the signs of these forces. A C-C-C
node resists three compressive forces, a C-C-T node resists
two compressive forces and one tensile force, and so on.
CODE COMMENTARY
Strut — A compression member in a strut-and-tie Strut — In design, struts are usually idealized as prismatic
model. A strut represents the resultant of a parallel or compression members, as shown by the straight line
a fan-shaped compression field. outlines of the struts in Fig. RA.1.2 and RA.1.3. If the effec-
tive compression strength fce differs at the two ends of a
strut, due either to different nodal zone strengths at the two
ends, or to different bearing lengths, the strut is idealized as
a uniformly tapered compression member.
Bottle-shaped strut — A strut that is wider at mid- Bottle-shaped struts — A bottle-shaped strut is a strut located
length than at its ends. in a part of a member where the width of the compressed
concrete at midlength of the strut can spread laterally.A.1,A.3
The curved dashed outlines of the struts in Fig. RA.1.3
and the curved solid outlines in Fig. RA.1.8 approximate
the boundaries of bottle-shaped struts. A split cylinder
test is an example of a bottle-shaped strut. The internal
lateral spread of the applied compression force in such a
test leads to a transverse tension that splits the specimen.
CODE COMMENTARY
Strut-and-tie model — A truss model of a structural Strut-and-tie model — The components of a strut-and-tie
member, or of a D-region in such a member, made up model of a single-span deep beam loaded with a concen-
of struts and ties connected at nodes, capable of trated load are identified in Fig. RA.1.3. The cross-sectional
transferring the factored loads to the supports or to dimensions of a strut or tie are designated as thickness and
adjacent B-regions. width, both perpendicular to the axis of the strut or tie.
Thickness is perpendicular to the plane of the truss model,
and width is in the plane of the truss model.
Tie — A tension member in a strut-and-tie model. Tie — A tie consists of reinforcement or prestressing steel
plus a portion of the surrounding concrete that is concentric
with the axis of the tie. The surrounding concrete is
included to define the zone in which the forces in the struts
and ties are to be anchored. The concrete in a tie is not used
to resist the axial force in the tie. Although not considered in
design, the surrounding concrete will reduce the elongations
of the tie, especially at service loads.
A.2 — Strut-and-tie model design procedure RA.2 — Strut-and-tie model design procedure
A.2.1 — It shall be permitted to design structural RA.2.1 — The truss model described in A.2.1 is referred to
concrete members, or D-regions in such members, by as a strut-and-tie model. Details of the use of strut-and-tie
modeling the member or region as an idealized truss. models are given in References A.1 through A.7. The design
The truss model shall contain struts, ties, and nodes of a D-region includes the following four steps:
as defined in A.1. The truss model shall be capable of
transferring all factored loads to the supports or 1. Define and isolate each D-region;
adjacent B-regions.
2. Compute resultant forces on each D-region boundary;
A.2.2 — The strut-and-tie model shall be in equilibrium 3. Select a truss model to transfer the resultant forces across
with the applied loads and the reactions. the D-region. The axes of the struts and ties, respectively,
are chosen to approximately coincide with the axes of the
compression and tension fields. The forces in the struts
and ties are computed.
A.2.3 — In determining the geometry of the truss, the RA.2.3 — The struts, ties, and nodal zones making up the
dimensions of the struts, ties, and nodal zones shall be strut-and-tie model all have finite widths that should be
taken into account. taken into account in selecting the dimensions of the truss.
Figure RA.2.3(a) shows a node and the corresponding nodal
zone. The vertical and horizontal forces equilibrate the force
in the inclined strut. If the stresses are equal in all three
struts, a hydrostatic nodal zone can be used and the widths
of the struts will be in proportion to the forces in the struts.
CODE COMMENTARY
A.2.5 — The angle, θ, between the axes of any strut RA.2.5 — The angle between the axes of struts and ties
and any tie entering a single node shall not be taken acting on a node should be large enough to mitigate cracking
as less than 25 degrees. and to avoid incompatibilities due to shortening of the struts
and lengthening of the ties occurring in almost the same
directions. This limitation on the angle prevents modeling the
shear spans in slender beams using struts inclined at less than
25 degrees from the longitudinal steel. See Reference A.6.
CODE COMMENTARY
A.2.6 — Design of struts, ties, and nodal zones shall RA.2.6 — Factored loads are applied to the strut-and-tie
be based on model, and the forces in all the struts, ties, and nodal zones
are computed. If several loading cases exist, each should be
φFn ≥ Fu (A-1) investigated. The strut-and-tie model, or models, are
analyzed for the loading cases and, for a given strut, tie, or
where Fu is the factored force acting in a strut, in a tie, nodal zone, Fu is the largest force in that element for all
or on one face of a nodal zone; Fn is the nominal loading cases.
strength of the strut, tie, or nodal zone; and φ is speci-
fied in 9.3.2.6.
A.3.1 — The nominal compressive strength of a strut RA.3.1 — The width of strut ws used to compute Acs is the
without longitudinal reinforcement, Fns , shall be taken smaller dimension perpendicular to the axis of the strut at the
as the smaller value of ends of the strut. This strut width is illustrated in Fig. RA.1.4(a)
and Fig. RA.1.5(a) and (b). In two-dimensional structures,
Fns = fce Acs (A-2) such as deep beams, the thickness of the struts may be taken
as the width of the member.
at the two ends of the strut, where Acs is the cross-
sectional area at one end of the strut, and fce is the
smaller of (a) and (b):
A.3.2 — The effective compressive strength of the RA.3.2 — The strength coefficient, 0.85fc′ , in Eq. (A-3)
concrete, fce , in a strut shall be taken as represents the effective concrete strength under sustained
compression, similar to that used in Eq. (10-1) and (10-2).
fce = 0.85βsfc′ (A-3)
A.3.2.1 — For a strut of uniform cross-sectional area RA.3.2.1 — The value of βs in A.3.2.1 applies to a strut
over its length ................................................. βs = 1.0 equivalent to the rectangular stress block in a compression
zone in a beam or column.
A.3.2.2 — For struts located such that the width of RA.3.2.2 — The value of βs in A.3.2.2 applies to bottle-
the midsection of the strut is larger than the width at shaped struts as shown in Fig. RA.1.3. The internal lateral
the nodes (bottle-shaped struts): spread of the compression forces can lead to splitting parallel
to the axis of the strut near the ends of the strut, as shown in
(a) With reinforcement satisfying A.3.3...... βs = 0.75 Fig. RA.1.8. Reinforcement placed to resist the splitting
force restrains crack width, allows the strut to resist more
A (b) Without reinforcement satisfying axial load, and permits some redistribution of force.
A.3.3 ........................................................ βs = 0.60λ
where the value of λ is defined in 8.6.1. The value of βs in A.3.2.2(b) includes the correction factor,
λ, for lightweight concrete because the strength of a strut
without transverse reinforcement is assumed to be limited to
less than the load at which longitudinal cracking develops.
A.3.2.3 — For struts in tension members, or the RA.3.2.3 — The value of βs in A.3.2.3 applies, for
tension flanges of members.......................... βs = 0.40 example, to compression struts in a strut-and-tie model used
to design the longitudinal and transverse reinforcement of
the tension flanges of beams, box girders, and walls. The
low value of βs reflects that these struts need to transfer
compression across cracks in a tension zone.
CODE COMMENTARY
A.3.2.4 — For all other cases.................. βs = 0.60λ RA.3.2.4 — The value of βs in A.3.2.4 applies to strut
applications not included in A.3.2.1, A.3.2.2, and A.3.2.3.
Examples are struts in a beam web compression field in the
web of a beam where parallel diagonal cracks are likely to
divide the web into inclined struts, and struts are likely to be
crossed by cracks at an angle to the struts (see Fig. RA.3.2(a)
and (b)). Section A.3.2.4 gives a reasonable lower limit on
βs except for struts described in A.3.2.2(b) and A.3.2.3.
A.3.3 — If the value of βs specified in A.3.2.2(a) is RA.3.3 — The reinforcement required by A.3.3 is related to
used, the axis of the strut shall be crossed by reinforce- the tension force in the concrete due to the spreading of the
ment proportioned to resist the transverse tensile force strut, as shown in the strut-and-tie model in Fig. RA.1.8(b).
resulting from the compression force spreading in the Section RA.3.3 allows the use of local strut-and-tie models
strut. It shall be permitted to assume the compressive to compute the amount of transverse reinforcement needed
force in the strut spreads at a slope of 2 longitudinal to in a given strut. The compressive forces in the strut may be
1 transverse to the axis of the strut. assumed to spread at a 2:1 slope, as shown in Fig. RA.1.8(b).
For specified concrete compressive strengths not exceeding
A.3.3.1 — For fc′ not greater than 40 MPa, the 40 MPa, the amount of reinforcement required by Eq. (A-4)
requirement of A.3.3 shall be permitted to be satisfied is deemed to satisfy A.3.3.
by the axis of the strut being crossed by layers of
reinforcement that satisfy Eq. (A-4) Figure RA.3.3 shows two layers of reinforcement crossing a
cracked strut. If the crack opens without shear slip along the
A si crack, bars in layer i in the figure will cause a stress
Σ -----------sinα i ≥ 0.003 (A-4) perpendicular to the strut of
bs si
A si f si
where Asi is the total area of surface reinforcement at ------------- sin α i
spacing si in the i-th layer of reinforcement crossing a bs si
strut at an angle αi to the axis of the strut.
CODE COMMENTARY
A.3.3.2 — The reinforcement required in A.3.3 shall RA.3.3.2 — In a corbel with a shear span-to-depth ratio
be placed in either two orthogonal directions at angles less than 1.0, the confinement reinforcement required to
α1 and α2 to the axis of the strut, or in one direction at satisfy A.3.3 is usually provided in the form of horizontal
an angle α to the axis of the strut. If the reinforcement is stirrups crossing the inclined compression strut, as shown in
in only one direction, α shall not be less than 40 degrees. Fig. R11.8.2.
A.3.4 — If documented by tests and analyses, it shall RA.3.4 — The design of tendon anchorage zones for
be permitted to use an increased effective compressive prestressed concrete sometimes uses confinement to enhance
strength of a strut due to confining reinforcement. the compressive strength of the struts in the local zone.
Confinement of struts is discussed in References A.4 and A.8.
A
A.3.5 — The use of compression reinforcement shall RA.3.5 — The strength added by the reinforcement is given
be permitted to increase the strength of a strut. by the last term in Eq. (A-5). The stress fs′ in the reinforcement
Compression reinforcement shall be properly in a strut at nominal strength can be obtained from the
anchored, parallel to the axis of the strut, located strains in the strut when the strut crushes. For Grade 40 or
within the strut, and enclosed in ties or spirals satisfying 60 reinforcement, fs′ can be taken as fy.
7.10. In such cases, the nominal strength of a longi-
tudinally reinforced strut is
CODE COMMENTARY
A.4 — Strength of ties RA.4 — Strength of ties
where (fse + Δfp) shall not exceed fpy , and Atp is zero
for nonprestressed members.
A.4.2 — The axis of the reinforcement in a tie shall RA.4.2 — The effective tie width assumed in design wt can
coincide with the axis of the tie in the strut-and-tie vary between the following limits, depending on the distri-
model. bution of the tie reinforcement:
(a) If the bars in the tie are in one layer, the effective tie
width can be taken as the diameter of the bars in the tie
plus twice the cover to the surface of the bars, as shown in
Fig. RA.1.5(a); and
CODE COMMENTARY
A.4.3.4 — The transverse reinforcement required by
A.3.3 shall be anchored in accordance with 12.13.
A.5.1 — The nominal compression strength of a nodal RA.5.1 — If the stresses in all the struts meeting at a node
zone, Fnn, shall be are equal, a hydrostatic nodal zone can be used. The faces of
such a nodal zone are perpendicular to the axes of the struts,
Fnn = fceAnz (A-7) and the widths of the faces of the nodal zone are proportional
to the forces in the struts.
where fce is the effective compressive strength of the
concrete in the nodal zone as given in A.5.2, and Anz Assuming the principal stresses in the struts and ties act
is the smaller of (a) and (b): parallel to the axes of the struts and ties, the stresses on
A faces perpendicular to these axes are principal stresses, and
(a) The area of the face of the nodal zone on which Fu A5.1(a) is used. If, as shown in Fig. RA.1.5(b), the face of a
acts, taken perpendicular to the line of action of Fu ; nodal zone is not perpendicular to the axis of the strut, there
will be both shear stresses and normal stresses on the face of
(b) The area of a section through the nodal zone, the nodal zone. Typically, these stresses are replaced by the
taken perpendicular to the line of action of the normal (principal compression) stress acting on the cross-
resultant force on the section. sectional area Ac of the strut, taken perpendicular to the axis
of the strut as given in A.5.1(a).
CODE COMMENTARY
to a resultant force in the nodal zone. In Fig. RA.1.6(b), the
vertical face which divide the nodal zone into two parts is
stressed by the resultant force acting along A-B. The design
of the nodal zone is governed by the critical section from
A.5.1(a) or A.5.1(b), whichever gives the highest stress.
A.5.2 — Unless confining reinforcement is provided RA.5.2 — The nodes in two-dimensional members, such as
within the nodal zone and its effect is supported by tests deep beams, can be classified as C-C-C if all the members
and analysis, the calculated effective compressive intersecting at the node are in compression; as C-C-T nodes
stress, fce , on a face of a nodal zone due to the strut- if one of the members acting on the node is in tension; and
and-tie forces shall not exceed the value given by so on, as shown in Fig. RA.1.7. The effective compressive
strength of the nodal zone is given by Eq. (A-8), as modified
fce = 0.85βnfc′ (A-8) by A.5.2.1 through A.5.2.3 apply to C-C-C nodes, C-C-T
nodes, and C-T-T or T-T-T nodes, respectively.
where the value of βn is given in A.5.2.1 through
A.5.2.3. The βn values reflect the increasing degree of disruption of
the nodal zones due to the incompatibility of tension strains
A.5.2.1 — In nodal zones bounded by in the ties and compression strains in the struts. The stress
struts or bearing areas, or both ..................... βn = 1.0; on any face of the nodal zone or on any section through the
nodal zone should not exceed the value given by Eq. (A-8),
A.5.2.2 — In nodal zones anchoring as modified by A.5.2.1 through A.5.2.3.
one tie.......................................................... βn = 0.80;
oder
A.5.3 — In a three-dimensional strut-and-tie model, RA.5.3 — This description of the shape and orientation of
the area of each face of a nodal zone shall not be less the faces of the nodal zones is introduced to simplify the
than that given in A.5.1, and the shape of each face of calculations of the geometry of a three-dimensional strut-
the nodal zones shall be similar to the shape of the and-tie model.
projection of the end of the struts onto the corresponding
faces of the nodal zones.
Design for flexure and axial load by provisions of Reinforcement limits, strength reduction factors φ, and
Appendix B shall be permitted. When Appendix B is moment redistribution in Appendix B differ from those in
used in design, B.8.4, B.8.4.1, B.8.4.2, and B.8.4.3 shall the main body of the Code. Appendix B contains the reinforce-
replace the corresponding numbered sections in ment limits, strength reduction factors φ, and moment redis-
Chapter 8; B.10.3.3 shall replace 10.3.3, 10.3.4, and tribution used in the Code for many years. Designs using the
10.3.5, except 10.3.5.1 shall remain; B.18.1.3, B.18.8.1, provisions of Appendix B satisfy the Code, and are equally
B.18.8.2, and B.18.8.3 shall replace the corresponding acceptable.
numbered sections in Chapter 18; B.18.10.4,
B.18.10.4.1, B.18.10.4.2, and B.18.10.4.3 shall replace When this appendix is used, the corresponding Commentary
18.10.4, 18.10.4.1, and 18.10.4.2. If any section in this sections apply. The load factors and strength reduction
appendix is used, all sections in this appendix shall be factors of either Chapter 9 or Appendix C are applicable.
substituted in the body of the Code, and all other
sections in the body of the Code shall be applicable.
For criteria on moment redistribution for prestressed Moment redistribution is dependent on adequate ductility in
concrete members, see B.18.10.4. plastic hinge regions. These plastic hinge regions develop at
sections of maximum positive or negative moment and
B.8.4.1 — Except where approximate values for cause a shift in the elastic moment diagram. The usual
moments are used, it shall be permitted to decrease results are reduction in the values of maximum negative
factored moments calculated by elastic theory at moments in the support regions and an increase in the
sections of maximum negative or maximum positive values of positive moments between supports from those
moment and in any span of continuous flexural computed by elastic analysis. However, because negative
members for any assumed loading arrangement by moments are determined for one loading arrangement and
not more than positive moments for another (see 13.7.6 for an exception),
economies in reinforcement can sometimes be realized by
20 ⎛ 1 – ρ – ρ′ reducing maximum elastic positive moments and increasing
⎝ --------------⎞⎠ percent
ρ b
negative moments, thus narrowing the envelope of
maximum negative and positive moments at any section in
the span. The plastic hinges permit the utilization of the full
B.8.4.2 — Redistribution of moments shall be made
capacity of more cross sections of a flexural member at
only when the section at which moment is reduced is
ultimate loads.
so designed that ρ or ρ – ρ′ is not greater than 0.50ρb ,
where
Before 2008, the Code addressed moment redistribution by
permitting an increase or decrease of factored negative
0.85β 1 f c ′ ⎛ 600 ⎞ moments above or below elastically calculated values,
ρ b = ------------------------
- ---------------------- (B-1)
fy ⎝ 600 + f ⎠ within specified limits. A decrease in negative moment
y
strength implies inelastic behavior in the negative moment B
B.8.4.3 — The reduced moment shall be used for region at the support. By increasing the negative moment
calculating redistributed moments at all other sections strength, the positive moments can be reduced but the result
within the spans. Static equilibrium shall be main- is that inelastic behavior will occur in the positive moment
tained after redistribution of moments at each loading region of the member and the percentage change in the positive
arrangement. moment section could be much larger than the 20 percent
permitted for negative moment sections.B.1 The 2008
change places the same percentage limitations on both
positive and negative moments.
CODE COMMENTARY
B.10.3 — General principles and requirements RB.10.3 — General principles and requirements
B.10.3.3 — For flexural members and members RB.10.3.3 — The maximum amount of tension reinforce-
B subject to combined flexure and compressive axial ment in flexural members is limited to ensure a level of
load where φPn is less than the smaller of 0.10fc′ Ag ductile behavior.
and φPb, the ratio of reinforcement, ρ, provided shall
not exceed 0.75 of the ratio ρb that would produce The nominal flexural strength of a section is reached when
balanced strain conditions for the section under flexure the strain in the extreme compression fiber reaches the
without axial load. For members with compression rein- limiting strain in the concrete. At ultimate strain of the
forcement, the portion of ρb equalized by compression concrete, the strain in the tension reinforcement could just
reinforcement need not be reduced by the 0.75 factor. reach the strain at first yield, be less than the yield strain
(elastic), or exceed the yield strain (inelastic). The steel strain
that exists at limiting concrete strain depends on the relative
proportion of steel to concrete and material strengths fc′ and fy.
CODE COMMENTARY
If ρ( fy /fc′ ) is sufficiently low, the strain in the tension steel
will greatly exceed the yield strain when the concrete strain
reaches its limiting value, with large deflection and ample
warning of impending failure (ductile failure condition). With
a larger ρ( fy /fc′ ), the strain in the tension steel may not reach
the yield strain when the concrete strain reaches its limiting
value, with consequent small deflection and little warning of
impending failure (brittle failure condition). For design it is
considered more conservative to restrict the nominal strength
condition so that a ductile failure mode can be expected.
B.18.1.3 — The following provisions of this Code shall RB.18.1.3 — Some sections of the Code are excluded from
not apply to prestressed concrete, except as specifi- use in the design of prestressed concrete for specific
cally noted: Sections 6.4.4, 7.6.5, B.8.4, 8.12.2, reasons. The following discussion provides an explanation
8.12.3, 8.12.4, 8.13, B.10.3.3, 10.5, 10.6, 10.9.1, and for such exclusions:
10.9.2; Chapter 13; and Sections 14.3, 14.5, and 14.6.
Section 6.4.4 — Tendons of continuous post-tensioned
beams and slabs are usually stressed at a point along the
span where the tendon profile is at or near the centroid of
the concrete cross section. Therefore, interior construction
joints are usually located within the end thirds of the span,
rather than the middle third of the span as required by 6.4.4.
Construction joints located as described in continuous post-
tensioned beams and slabs have a long history of satisfactory
performance. Thus, 6.4.4 is excluded from application to
prestressed concrete.
CODE COMMENTARY
prestressed concrete, would exclude many standard
prestressed products in satisfactory use today. Hence, proof
by experience permits variations.
CODE COMMENTARY
B.18.8 — Limits for reinforcement of flexural RB.18.8 — Limits for reinforcement of flexural
members members
B.18.8.1 — Ratio of prestressed and nonprestressed RB.18.8.1 — The terms ωp , [ωp + (d/dp)(ω – ω′)] and [ωpw
reinforcement used for computation of moment + (d/dp)(ωw – ωw′ )] are each equal to 0.85a/dp, where a is
strength of a member, except as provided in B.18.8.2, the depth of the equivalent rectangular stress block for the
shall be such that ωp , [ωp + (d/dp)(ω – ω′)], or [ωpw + section under consideration, as defined in 10.2.7.1. Use of
(d/dp)(ωw – ωw′ )] is not greater than 0.36β1, except as this relationship can simplify the calculations necessary to
permitted in B.18.8.2. check compliance with RB.18.8.1.
B.18.8.2 — When a reinforcement ratio exceeds the RB.18.8.2 — Design moment strength of over-reinforced
limit specified in B.18.8.1 is provided, design moment sections may be computed using strength equations similar
strength shall not exceed the moment strength based to those for nonprestressed concrete members. The 1983
on the compression portion of the moment couple. Code provided strength equations for rectangular and
flanged sections.
B.18.8.3 — Total amount of prestressed and nonpre- RB.18.8.3 — This provision is a precaution against abrupt
stressed reinforcement shall be adequate to develop flexural failure developing immediately after cracking. A
a factored load at least 1.2 times the cracking load flexural member designed according to Code provisions
computed on the basis of the modulus of rupture fr in requires considerable additional load beyond cracking to
9.5.2.3. This provision shall be permitted to be reach its flexural strength. This additional load should result
waived for: in considerable deflection that would warn when the
member nominal strength is being approached. If the flex-
(a) two-way, unbonded post-tensioned slabs; and ural strength is reached shortly after cracking, the warning
deflection would not occur.
(b) flexural members with shear and flexural strength
at least twice that required by 9.2. Due to the very limited extent of initial cracking in the negative
moment region near columns of two-way flat plates, deflection
under load does not reflect any abrupt change in stiffness as
the modulus of rupture of concrete is reached.
CODE COMMENTARY
B.18.10 — Statically indeterminate structures RB.18.10 — Statically indeterminate structures
B.18.10.3 — Moments to be used to compute required RB.18.10.3 — For statically indeterminate structures, the
strength shall be the sum of the moments due to reac- moments due to reactions induced by prestressing forces,
tions induced by prestressing (with a load factor of 1.0) referred to as secondary moments, are significant in both the
and the moments due to factored loads. Adjustment of elastic and inelastic states. When hinges and full redistribution
the sum of these moments shall be permitted as of moments occur to create a statically determinate structure,
allowed in B.18.10.4. secondary moments disappear. However, the elastic defor-
mations caused by a nonconcordant tendon change the
amount of inelastic rotation required to obtain a given
amount of moment redistribution. Conversely, for a beam
with a given inelastic rotation capacity, the amount by
which the moment at the support may be varied is changed
by an amount equal to the secondary moment at the support
due to prestressing. Thus, the Code requires that secondary
moments be included in determining design moments.
B.18.10.4.2 — Redistribution of moments shall be The amount of redistribution allowed depends on the ability of
made only when the section at which moment is the critical sections to deform inelastically by a sufficient
CODE COMMENTARY
reduced is so designed that ωp , [ωp + (d/dp)(ω – ω′ )] amount. Serviceability is addressed in 18.4. The choice of
or [ωpw + (d/dp)(ωw – ωw′ )], whichever is applicable, is 0.24β1 as the largest tension reinforcement index, ωp , [ωp
not greater than 0.24β1. + (d/dp)(ω – ω′)] or [ωpw + (d/dp)(ωw – ωw′ )], for which
redistribution of moments is allowed, is in agreement with
B.18.10.4.3 — The reduced moment shall be used the requirements for nonprestressed concrete of 0.5ρb stated
for calculating redistributed moments at all other in B.8.4.
sections within the spans. Static equilibrium shall be
maintained after redistribution of moments for each The terms ωp, [ωp + (d/dp)(ω – ω′ )], and [ωpw + (d/dp)(ωw
loading arrangement. – ωw′ )] appear in B.18.10.4.1 and B.18.10.4.3 and are each
equal to 0.85a/dp, where a is the depth of the equivalent
rectangular stress distribution for the section under consid-
eration, as defined in 10.2.7.1. Use of this relationship can
simplify the calculations necessary to determine the amount
of moment redistribution permitted by B.18.10.4.1 and to
check compliance with the limitation on flexural reinforcement
contained in B.18.10.4.3.
Structural concrete shall be permitted to be designed RC.9.1.1 — In the 2002 Code, the load and strength reduction
using the load combinations and strength reduction factors formerly in Chapter 9 were revised and moved to
factors of Appendix C. When Appendix C is used in this appendix. They have evolved since the early 1960s and
design, C.9.2.1 through C.9.2.7 shall replace 9.2.1 are considered to be reliable for concrete construction.
through 9.2.5 and C.9.3.1 through C.9.3.5 shall
replace 9.3.1 through 9.3.5.
C.9.2.1 — Required strength U to resist dead load D The wind load equation in ASCE 7-98 and IBC 2000C.1
and live load L shall not be less than includes a factor for wind directionality that is equal to 0.85
for buildings. The corresponding load factor for wind in the
U = 1.4D + 1.7L (C.9-1) load combination equations was increased accordingly (1.3/
0.85 = 1.53, rounded up to 1.6). The Code allows use of the
C.9.2.2 — For structures that also resist W, wind load, previous wind load factor of 1.3 when the design wind load
or E, the load effects of earthquake, U shall not be less is obtained from other sources that do not include the wind
than the larger of Eq. (C.9-1), (C.9-2), and (C.9-3) directionality factor.
U = 0.75(1.4D + 1.7L) + (1.6W or 1.0E) (C.9-2) Model building codes and design load references have
converted earthquake forces to strength level, and reduced
and the earthquake load factor to 1.0 (ASCE 7-93C.2; BOCA/
NBC 93C.3; SBC 94C.4; UBC 97C.5; and IBC 2000C.1 ). The
U = 0.9D + (1.6W or 1.0E) (C.9-3) Code requires use of the previous load factor for earthquake
loads, approximately 1.4, when service-level earthquake
Where W has not been reduced by a directionality forces from earlier editions of these references are used.
factor, it shall be permitted to use 1.3W in place of
1.6W in Eq. (C.9-2) and (C.9-3). Where E is based on
service-level seismic forces, 1.4E shall be used in
place of 1.0E in Eq. (C.9-2) and (C.9-3).
C.9.2.3 — For structures that resist H, loads due to RC.9.2.3 — If effects H caused by earth pressure, ground-
weight and pressure of soil, water in soil, or other water pressure, or pressure caused by granular materials are
related materials, U shall not be less than the larger of included in design, the required strength equations become
Eq. (C.9-1) and (C.9-4):
U = 1.4D + 1.7L + 1.7H
U = 1.4D + 1.7L + 1.7H (C.9-4)
and where D or L reduce the effect of H
In Eq. (C.9-4), where D or L reduce the effect of H, C
0.9D shall be substituted for 1.4D, and zero value of L U = 0.9D + 1.7H
shall be used to determine the greatest required
strength U. but for any combination of D, L, or H
U = 1.4D + 1.7L
CODE COMMENTARY
C.9.2.4 — For structures that resist F, load due to RC.9.2.4 — This section addresses the need to consider
weight and pressure of fluids with well-defined densities, loading due to weight of liquid or liquid pressure. It specifies
the load factor for F shall be 1.4, and F shall be added a load factor for such loadings with well-defined densities
to all loading combinations that include L. and controllable maximum heights equivalent to that used
for dead load. Such reduced factors would not be appropriate
where there is considerable uncertainty of pressures, as with
groundwater pressures, or uncertainty as to the possible
maximum liquid depth, as in ponding of water. See R8.2.
U = 0.9D + 1.4F
U = 1.4D + 1.7L
C.9.2.5 — If resistance to impact effects is taken into RC.9.2.5 — If the live load is applied rapidly, as may be the
account in design, such effects shall be included with L. case for parking structures, loading docks, warehouse
floors, elevator shafts, etc., impact effects should be
considered. In all equations, substitute (L + impact) for L
when impact must be considered.
C.9.2.6 — Where structural effects of differential RC.9.2.6 — The effects of differential settlement, creep,
settlement, creep, shrinkage, expansion of shrinkage- shrinkage, temperature, and shrinkage-compensating
compensating concrete, or temperature change, T, concrete should be considered. The term “realistic assessment”
are significant, U shall not be less than the larger of is used to indicate that the most probable values, rather than
Eq. (C.9-5) and (C.9-6) the upper bound values, of the variables should be used.
U = 0.75(1.4D + 1.4T + 1.7L) (C.9-5) Equation (C.9-6) is to prevent a design for load
C.9.2.7 — For post-tensioned anchorage zone design, RC.9.2.7 — The load factor of 1.2 applied to the
a load factor of 1.2 shall be applied to the maximum maximum prestressing steel jacking force results in a
prestressing steel jacking force. design load of 113 percent of the specified yield strength
C of prestressing steel but not more than 96 percent of the
nominal ultimate strength of the tendon. This compares
well with a maximum attainable jacking force, which is
limited by the anchor efficiency factor.
CODE COMMENTARY
C.9.3 — Design strength RC.9.3 — Design strength
C.9.3.1 — Design strength provided by a member, its RC.9.3.1 — The term “design strength” of a member refers
connections to other members, and its cross sections, to the nominal strength calculated in accordance with the
in terms of flexure, axial load, shear, and torsion, shall requirements stipulated in this Code multiplied by a strength
be taken as the nominal strength calculated in accor- reduction factor φ that is always less than 1.
dance with requirements and assumptions of this
Code, multiplied by the φ factors in C.9.3.2, C.9.3.4, The purposes of the strength reduction factor φ are: (1) to
and C.9.3.5. allow for the probability of understrength members due to
variations in material strengths and dimensions; (2) to allow
for inaccuracies in the design equations; (3) to reflect the
degree of ductility and required reliability of the member
under the load effects being considered; and (4) to reflect
the importance of the member in the structure. For example,
a lower φ is used for columns than for beams because
columns generally have less ductility, are more sensitive to
variations in concrete strength, and generally support larger
loaded areas than beams. Furthermore, spiral columns are
assigned a higher φ than tied columns since they have
greater ductility or toughness.
C.9.3.2.1 — Tension-controlled sections, as defined RC.9.3.2.1 — In applying C.9.3.2.1 and C.9.3.2.2, the
in 10.3.4 (See also C.9.3.2.7)................................ 0.90 axial tensions and compressions to be considered are those
caused by external forces. Effects of prestressing forces are
not included.
C.9.3.2.2 — Compression-controlled sections, as RC.9.3.2.2 — Before the 2002 edition, the Code gave the
defined in 10.3.3: magnitude of the φ-factor for cases of axial load or flexure,
or both, in terms of the type of loading. For these cases, the
(a) Members with spiral reinforcement φ-factor is now determined by the strain conditions at a
conforming to 10.9.3 .......................................... 0.75 cross section, at nominal strength.
(b) Other reinforced members ............................ 0.70 A lower φ-factor is used for compression-controlled
For sections in which the net tensile strain in the sections than is used for tension-controlled sections because
extreme tension steel at nominal strength, εt , is compression-controlled sections have less ductility, are
between the limits for compression-controlled and more sensitive to variations in concrete strength, and generally
tension-controlled sections, φ shall be permitted to be occur in members that support larger loaded areas than
linearly increased from that for compression-controlled members with tension-controlled sections. Members with
sections to 0.90 as εt increases from the compression- spiral reinforcement are assigned a higher φ than tied
controlled strain limit to 0.005. columns since they have greater ductility or toughness.
Alternatively, when Appendix B is used, for members For sections subjected to axial load with flexure, design
in which fy does not exceed 420 MPa, with symmetric strengths are determined by multiplying both Pn and Mn by
reinforcement, and with (d – d′)/h not less than 0.70, φ the appropriate single value of φ. Compression-controlled
and tension-controlled sections are defined in 10.3.3 and C
shall be permitted to be increased linearly to 0.90 as
φPn decreases from 0.10fc′ Ag to zero. For other rein- 10.3.4 as those that have net tensile strain in the extreme
forced members, φ shall be permitted to be increased tension steel at nominal strength less than or equal to the
linearly to 0.90 as φPn decreases from 0.10fc′ Ag or compression-controlled strain limit, and equal to or greater
φPb , whichever is smaller, to zero. than 0.005, respectively. For sections with net tensile strain
εt in the extreme tension steel at nominal strength between
the above limits, the value of φ may be determined by linear
interpolation, as shown in Fig. RC.9.3.2. The concept of net
tensile strain εt is discussed in R10.3.3.
CODE COMMENTARY
C.9.3.2.5 — Post-tensioned anchorage zones ......0.85 RC.9.3.2.5 — The φ-factor of 0.85 reflects the wide scatter of
C results of experimental anchorage zone studies. Since 18.13.4.2
limits the nominal compressive strength of unconfined
concrete in the general zone to 0.7λfci′ , the effective design
strength for unconfined concrete is 0.85 × 0.7λfci′ ≈ 0.6λfci′ .
CODE COMMENTARY
C.9.3.2.7 — Flexure sections without axial load in RC.9.3.2.7 — If a critical section occurs in a region
pretensioned members where strand embedment is where strand is not fully developed, failure may be by bond
less than the development length as provided in slip. Such a failure resembles a brittle shear failure; hence
12.9.1.1 ................................................................. 0.85 the requirement for a reduced φ.
C.9.3.4 — For structures that rely on intermediate RC.9.3.4 — Section C.9.3.4(a) refers to brittle members,
precast structural walls in Seismic Design Category D, such as low-rise walls or portions of walls between openings,
E, or F, special moment frames, or special structural or diaphragms that are impractical to reinforce to raise their
walls to resist E, φ shall be modified as given in (a) nominal shear strength above nominal flexural strength for
through (c): the pertinent loading conditions.
(a) For any structural member that is designed to Short structural walls were the primary vertical elements of
resist E, φ for shear shall be 0.60 if the nominal the lateral-force-resisting system in many of the parking
shear strength of the member is less than the shear structures that sustained damage during the 1994
corresponding to the development of the nominal Northridge earthquake. Section C.9.3.4(b) requires the shear
flexural strength of the member. The nominal flexural strength reduction factor for diaphragms to be 0.60 if the
strength shall be determined considering the most shear strength reduction factor for the walls is 0.60.
critical factored axial loads and including E;
C.9.3.5 — In Chapter 22, φ shall be 0.65 for flexure, RC.9.3.5 — The strength reduction factor φ for structural
compression, shear, and bearing of structural plain plain concrete design is the same for all strength conditions.
concrete. Since both flexural tension strength and shear strength for
plain concrete depend on the tensile strength characteristics
of the concrete, with no reserve strength or ductility
possible due to the absence of reinforcement, equal strength
reduction factors for both bending and shear are considered
appropriate.
CODE COMMENTARY
D.1 — Definitions RD.1 — Definitions
Anchor group — A number of anchors of approxi- Anchor group — For all potential failure modes (steel,
mately equal effective embedment depth with each concrete breakout, pullout, side-face blowout, and pryout),
anchor spaced at less than 3hef from one or more adja- only those anchors susceptible to a particular failure mode
cent anchors when subjected to tension, or 3ca1 from should be considered when evaluating the strength associated
one or more adjacent anchors when subjected to shear. with that failure mode.
Only those anchors susceptible to the particular failure
mode under investigation shall be included in the group.
Brittle steel element — An element with a tensile test Brittle steel element and ductile steel element — The 14
elongation of less than 14 percent, or reduction in area percent elongation should be measured over the gauge length
of less than 30 percent, or both. specified in the appropriate ASTM standard for the steel.
CODE COMMENTARY
Ductile steel element — An element with a tensile test
elongation of at least 14 percent and reduction in area of
at least 30 percent. A steel element meeting the require-
ments of ASTM A307 shall be considered ductile.
Effective embedment depth — The overall depth Effective embedment depth — Effective embedment depths
through which the anchor transfers force to or from the for a variety of anchor types are shown in Fig. RD.1.
surrounding concrete. The effective embedment depth
will normally be the depth of the concrete failure surface
in tension applications. For cast-in headed anchor bolts
and headed studs, the effective embedment depth is
measured from the bearing contact surface of the head.
Five percent fractile — A statistical term meaning Five percent fractile — The determination of the coefficient
90 percent confidence that there is 95 percent probability K05 associated with the 5 percent fractile, x – K05ss depends
of the actual strength exceeding the nominal strength. on the number of tests, n, used to compute the sample mean,
x, and sample standard deviation, ss. Values of K05 range, for
example, from 1.645 for n = ∞, to 2.010 for n = 40, and 2.568
for n = 10. With this definition of the 5 percent fractile, the
nominal strength in D.4.2 is the same as the characteristic
strength in ACI 355.2.
CODE COMMENTARY
Hooked bolt — A cast-in anchor anchored mainly by
bearing of the 90-degree bend (L-bolt) or 180-degree
bend (J-bolt) against the concrete, at its embedded
end, and having a minimum eh of 3da.
D.2.1 — This appendix provides design requirements RD.2.1 — Appendix D is restricted in scope to structural
for anchors in concrete used to transmit structural anchors that transmit structural loads related to strength,
loads by means of tension, shear, or a combination of stability, or life safety. Two types of applications are
tension and shear between: (a) connected structural envisioned. The first is connections between structural
elements; or (b) safety-related attachments and struc- elements where the failure of an anchor or an anchor group
tural elements. Safety levels specified are intended for could result in loss of equilibrium or stability of any portion
in-service conditions, rather than for short-term of the structure. The second is where safety-related attach-
D
handling and construction conditions. ments that are not part of the structure (such as sprinkler
systems, heavy suspended pipes, or barrier rails) are
attached to structural elements. The levels of safety defined by
the combinations of load factors and φ-factors are appropriate
for structural applications. Other standards may require
more stringent safety levels during temporary handling.
CODE COMMENTARY
D.2.2 — This appendix applies to both cast-in anchors RD.2.2 — The wide variety of shapes and configurations of
and post-installed anchors. Specialty inserts, through- specialty inserts makes it difficult to prescribe generalized
bolts, multiple anchors connected to a single steel plate tests and design equations for many insert types. Hence,
at the embedded end of the anchors, adhesive or they have been excluded from the scope of Appendix D.
grouted anchors, and direct anchors such as powder or Adhesive anchors are widely used and can perform
pneumatic actuated nails or bolts, are not included. adequately. At this time, however, such anchors are outside
Reinforcement used as part of the embedment shall be the scope of this appendix.
designed in accordance with other parts of this Code.
D.2.3 — Headed studs and headed bolts having a RD.2.3 — Typical cast-in headed studs and headed bolts
geometry that has been demonstrated to result in a with geometries consistent with ANSI/ASME B1.1,D.1
pullout strength in uncracked concrete equal or B18.2.1,D.2 and B18.2.6D.3 have been tested and proven to
exceeding 1.4Np (where Np is given by Eq. (D-15)) are behave predictably, so calculated pullout values are acceptable.
included. Hooked bolts that have a geometry that has Post-installed anchors do not have predictable pullout
been demonstrated to result in a pullout strength without capacities, and therefore are required to be tested. For a
the benefit of friction in uncracked concrete equal or post-installed anchor to be used in conjunction with the
exceeding 1.4Np (where Np is given by Eq. (D-16)) are requirements of this appendix, the results of the ACI 355.2
included. Post-installed anchors that meet the tests have to indicate that pullout failures exhibit an acceptable
assessment requirements of ACI 355.2 are included. load-displacement characteristic or that pullout failures are
The suitability of the post-installed anchor for use in precluded by another failure mode.
concrete shall have been demonstrated by the ACI
355.2 prequalification tests.
D.2.4 — Load applications that are predominantly high RD.2.4 — The exclusion from the scope of load applications
cycle fatigue or impact loads are not covered by this producing high cycle fatigue or extremely short duration
appendix. impact (such as blast or shock wave) are not meant to
exclude seismic load effects. D.3.3 presents additional
requirements for design when seismic loads are included.
D.3.1 — Anchors and anchor groups shall be RD.3.1 — When the strength of an anchor group is
designed for critical effects of factored loads as deter- governed by breakage of the concrete, the behavior is brittle
mined by elastic analysis. Plastic analysis approaches and there is limited redistribution of the forces between the
are permitted where nominal strength is controlled by highly stressed and less stressed anchors. In this case, the
ductile steel elements, provided that deformational theory of elasticity is required to be used assuming the
compatibility is taken into account. attachment that distributes loads to the anchors is sufficiently
stiff. The forces in the anchors are considered to be
proportional to the external load and its distance from the
neutral axis of the anchor group.
D.3.3 — When anchor design includes earthquake RD.3.3 — Post-installed structural anchors are required to
forces for structures assigned to Seismic Design be qualified for Seismic Design Categories C, D, E, or F by
Category C, D, E, or F, the additional requirements of demonstrating the ability to undergo large displacements
D.3.3.1 through D.3.3.6 shall apply. through several cycles as specified in the seismic simulation
CODE COMMENTARY
tests of ACI 355.2. Because ACI 355.2 excludes plastic
hinge zones, Appendix D is not applicable to the design of
anchors in plastic hinge zones under seismic forces. In
addition, the design of anchors for earthquake forces is
based on a more conservative approach by the introduction
of 0.75 factor on the design strength φNn and φVn for the
concrete failure modes, and by requiring the system to have
adequate ductility. Anchor strength should be governed by
ductile yielding of a steel element. If the anchor cannot meet
these ductility requirements, then either the attachment is
designed to yield or the calculated anchor strength is
substantially reduced to minimize the possibility of a brittle
failure. In designing attachments for adequate ductility, the
ratio of yield to design strength should be considered. A connec-
tion element could yield only to result in a secondary failure as
one or more elements strain harden and fail if the design
strength is excessive when compared to the yield strength.
D.3.3.1 — The provisions of Appendix D do not RD.3.3.1 — Section 3.1 of ACI 355.2 specifically states
apply to the design of anchors in plastic hinge zones of that the seismic test procedures do not simulate the behavior
concrete structures under earthquake forces. of anchors in plastic hinge zones. The possible higher level
of cracking and spalling in plastic hinge zones are beyond
the damage states for which Appendix D is applicable.
D.3.3.2 — Post-installed structural anchors shall be RD.3.3.2 — Anchors that are not suitable for use in
qualified for use in cracked concrete and shall have cracked concrete should not be used to resist seismic loads.
passed the Simulated Seismic Tests in accordance
with ACI 355.2. Pullout strength Np and steel strength
of the anchor in shear Vsa shall be based on the
results of the ACI 355.2 Simulated Seismic Tests.
D.3.3.3 — The anchor design strength associated RD.3.3.3 — The anchor strength associated with concrete
with concrete failure modes shall be taken as 0.75φNn failure modes is to account for increased damage states in
and 0.75φVn, where φ is given in D.4.4 or D.4.5, and the concrete resulting from seismic actions. Because
Nn and Vn are determined in accordance with D.5.2, seismic design generally assumes that all or portions of the
D.5.3, D.5.4, D.6.2, and D.6.3, assuming the concrete structure are loaded beyond yield, it is likely that the
is cracked unless it can be demonstrated that the concrete is cracked throughout for the purpose of determining
concrete remains uncracked. the anchor strength unless it can be demonstrated that the
concrete remains uncracked.
D.3.3.4 — Anchors shall be designed to be RD.3.3.4 — Ductile steel anchor elements are required to
governed by the steel strength of a ductile steel satisfy the requirements of D.1, Ductile Steel Element. For
element as determined in accordance with D.5.1 and anchors loaded with a combination of tension and shear, the
D.6.1, unless either D.3.3.5 or D.3.3.6 is satisfied. strength in all loading directions must be controlled by the
steel strength of the ductile steel anchor element.
D
D.3.3.5 — Instead of D.3.3.4, the attachment that
the anchor is connecting to the structure shall be
designed so that the attachment will undergo ductile
yielding at a force level corresponding to anchor forces
no greater than the design strength of anchors specified
in D.3.3.3.
CODE COMMENTARY
D.3.3.6 — As an alternative to D.3.3.4 and D.3.3.5, it RD.3.3.6 — As a matter of good practice, a ductile failure
shall be permitted to take the design strength of the mode in accordance with D.3.3.4 or D.3.3.5 should be
anchors as 0.4 times the design strength determined provided for in the design of the anchor or the load should
in accordance with D.3.3.3. For the anchors of stud be transferred to anchor reinforcement in the concrete.
bearing walls, it shall be permitted to take the design Where this is not possible due to geometric or material
strength of the anchors as 0.5 times the design constraints, D.3.3.6 permits the design of anchors for non-
strength determined in accordance with D.3.3.3. ductile failure modes at a reduced permissible strength to
minimize the possibility of a brittle failure. The attachment
of light frame stud walls typically involves multiple anchors
that allow for load redistribution. This justifies the use of a
less conservative factor for this case.
D.3.5 — The values of fc′ used for calculation RD.3.5 — A limited number of tests of cast-in-place and
purposes in this appendix shall not exceed 70 MPa for post-installed anchors in high-strength concreteD.7 indicate
cast-in anchors, and 55 MPa for post-installed that the design procedures contained in this appendix
anchors. Testing is required for post-installed anchors become unconservative, particularly for cast-in anchors in
when used in concrete with fc′ greater than 55 MPa. concrete with compressive strengths in the range of 75 to
85 MPa. Until further tests are available, an upper limit on
fc′ of 70 MPa has been imposed in the design of cast-in-
place anchors. This is consistent with Chapters 11 and 12.
The companion ACI 355.2 does not require testing of post-
installed anchors in concrete with fc′ greater than 55 MPa
because some post-installed anchors may have difficulty
expanding in very high-strength concretes. Because of this,
fc′ is limited to 55 MPa in the design of post-installed
anchors unless testing is performed.
D.4 — General requirements for strength RD.4 — General requirements for strength
of anchors of anchors
D.4.1 — Strength design of anchors shall be based RD.4.1 — This section provides requirements for establishing
either on computation using design models that satisfy the strength of anchors to concrete. The various types of
the requirements of D.4.2, or on test evaluation using steel and concrete failure modes for anchors are shown in
the 5 percent fractile of test results for the following: Fig. RD.4.1(a) and RD.4.1(b). Comprehensive discussions
of anchor failure modes are included in References D.8 to
(a) Steel strength of anchor in tension (D.5.1); D.10. Any model that complies with the requirements of
D.4.2 and D.4.3 can be used to establish the concrete-
(b) Steel strength of anchor in shear (D.6.1); related strengths. For anchors such as headed bolts, headed
(c) Concrete breakout strength of anchor in tension studs, and post-installed anchors, the concrete breakout
(D.5.2); design methods of D.5.2 and D.6.2 are acceptable. The
anchor strength is also dependent on the pullout strength of
(d) Concrete breakout strength of anchor in shear D.5.3, the side-face blowout strength of D.5.4, and the
(D.6.2); minimum spacings and edge distances of D.8. The design of
anchors for tension recognizes that the strength of anchors is
(e) Pullout strength of anchor in tension (D.5.3); sensitive to appropriate installation; installation requirements
D
(f) Concrete side-face blowout strength of anchor in are included in D.9. Some post-installed anchors are less
tension (D.5.4); and sensitive to installation errors and tolerances. This is
reflected in varied φ-factors based on the assessment criteria
(g) Concrete pryout strength of anchor in shear of ACI 355.2.
(D.6.3).
Test procedures can also be used to determine the single-
anchor breakout strength in tension and in shear. The test
CODE COMMENTARY
In addition, anchors shall satisfy the required edge results, however, are required to be evaluated on a basis
distances, spacings, and thicknesses to preclude split- statistically equivalent to that used to select the values for
ting failure, as required in D.8. the concrete breakout method “considered to satisfy”
provisions of D.4.2. The basic strength cannot be taken
D.4.1.1 — For the design of anchors, except as greater than the 5 percent fractile. The number of tests has to
required in D.3.3, be sufficient for statistical validity and should be considered in
the determination of the 5 percent fractile.
φNn ≥ Nua (D-1)
CODE COMMENTARY
D.4.1.3 — When both Nua and Vua are present, interac-
tion effects shall be considered in accordance with D.4.3.
D.4.2 — The nominal strength for any anchor or group RD.4.2 and RD.4.3 — D.4.2 and D.4.3 establish the perfor-
of anchors shall be based on design models that result mance factors for which anchor design models are required
in predictions of strength in substantial agreement with to be verified. Many possible design approaches exist and
results of comprehensive tests. The materials used in the user is always permitted to “design by test” using D.4.2
the tests shall be compatible with the materials used in as long as sufficient data are available to verify the model.
the structure. The nominal strength shall be based on
the 5 percent fractile of the basic individual anchor
strength. For nominal strengths related to concrete
strength, modifications for size effects, the number of
anchors, the effects of close spacing of anchors, prox-
imity to edges, depth of the concrete member, eccentric
loadings of anchor groups, and presence or absence of
cracking shall be taken into account. Limits on edge
distances and anchor spacing in the design models
shall be consistent with the tests that verified the model.
D.4.2.1 — The effect of reinforcement provided to RD.4.2.1 — The addition of reinforcement in the direction
restrain the concrete breakout shall be permitted to be of the load to restrain concrete breakout can greatly enhance
included in the design models used to satisfy D.4.2. the strength and deformation capacity of the anchor connection.
Where anchor reinforcement is provided in accor- Such enhancement is practical with cast-in anchors such as
dance with D.5.2.9 and D.6.2.9, calculation of the those used in precast sections.
concrete breakout strength in accordance with D.5.2
and D.6.2 is not required. References D.8, D.11, D.12, D.13, and D.14 provide information
regarding the effect of reinforcement on the behavior of anchors.
The effect of reinforcement is not included in the ACI 355.2
anchor acceptance tests or in the concrete breakout calculation
method of D.5.2 and D.6.2. The beneficial effect of supplemen-
tary reinforcement is recognized by the Condition A φ-factors
in D.4.4 and D.4.5. Anchor reinforcement may be provided
instead of calculating breakout strength using the provisions of
Chapter 12 in conjunction with D.5.2.9 and D.6.2.9.
D.4.2.2 — For anchors with diameters not exceeding RD.4.2.2 — The method for concrete breakout design
50 mm, and tensile embedments not exceeding 635 mm included as “considered to satisfy” D.4.2 was developed from
in depth, the concrete breakout strength requirements the Concrete Capacity Design (CCD) Method,D.9,D.10 which
shall be considered satisfied by the design procedure was an adaptation of the κ MethodD.15,D.16 and is considered
of D.5.2 and D.6.2. to be accurate, relatively easy to apply, and capable of exten-
sion to irregular layouts. The CCD Method predicts the
strength of an anchor or group of anchors by using a basic
equation for tension, or for shear for a single anchor in
cracked concrete, and multiplied by factors that account for
D the number of anchors, edge distance, spacing, eccentricity,
and absence of cracking. The limitations on anchor size and
embedment length are based on the current range of test data.
CODE COMMENTARY
D.4.3 — Resistance to combined tensile and shear
loads shall be considered in design using an interaction
expression that results in computation of strength in
substantial agreement with results of comprehensive
tests. This requirement shall be considered satisfied
by D.7.
D.4.4 — Strength reduction factor φ for anchors in RD.4.4 — The φ-factors for steel strength are based on using
concrete shall be as follows when the load combinations futa to determine the nominal strength of the anchor (see D.5.1
of 9.2 are used: and D.6.1) rather than fya as used in the design of reinforced
concrete members. Although the φ-factors for use with futa
a) Anchor governed by strength of a ductile steel appear low, they result in a level of safety consistent with the
element use of higher φ-factors applied to fya. The smaller φ-factors for
shear than for tension do not reflect basic material differ-
i) Tension loads....................... 0.75 ences but rather account for the possibility of a non-uniform D
ii) Shear loads......................... 0.65 distribution of shear in connections with multiple anchors. It
b) Anchor governed by strength of a brittle steel is acceptable to have a ductile failure of a steel element in
element the attachment if the attachment is designed so that it will
undergo ductile yielding at a load level corresponding to
i) Tension loads....................... 0.65 anchor forces no greater than the minimum design strength
ii) Shear loads......................... 0.60 of the anchors specified in D.3.3. (See D.3.3.5.)
CODE COMMENTARY
c) Anchor governed by concrete breakout, side-face For anchors governed by the more brittle concrete breakout
blowout, pullout, or pryout strength or blowout failure, two conditions are recognized. If supple-
mentary reinforcement is present (Condition A), greater
Condition A Condition B deformation capacity is provided than in the case where
such supplementary reinforcement is not present (Condition B).
i) Shear loads 0.75 0.70 An explicit design of supplementary reinforcement is not
ii) Tension loads required. However, the arrangement of supplementary
reinforcement should generally conform to that of the
Cast-in headed studs, anchor reinforcement shown in Fig. RD.5.2.9 and
headed bolts, or hooked RD.6.2.9(b). Full development is not required.
bolts 0.75 0.70
The strength reduction factors for anchor reinforcement are
Post-installed anchors
given in D.5.2.9 and D.6.2.9. Further discussion of strength
with category as determined
reduction factors is presented in RD.4.5.
from ACI 355.2
The ACI 355.2 tests for sensitivity to installation procedures
Category 1 0.75 0.65
determine the category appropriate for a particular anchoring
(Low sensitivity
device. In the ACI 355.2 tests, the effects of variability in
to installation and
anchor torque during installation, tolerance on drilled hole
high reliability)
size, energy level used in setting anchors, and for anchors
approved for use in cracked concrete, increased crack widths
Category 2 0.65 0.55
are considered. The three categories of acceptable post-
(Medium sensitivity
installed anchors are:
to installation and
medium reliability)
Category 1 — low sensitivity to installation and high
reliability;
Category 3 0.55 0.45
(High sensitivity
Category 2 — medium sensitivity to installation and
to installation and
medium reliability; and
lower reliability)
Category 3 — high sensitivity to installation and lower
Condition A applies where supplementary reinforce-
reliability.
ment is present except for pullout and pryout strengths.
The capacities of anchors under shear loads are not as sensitive
Condition B applies where supplementary reinforce-
to installation errors and tolerances. Therefore, for shear
ment is not present, and for pullout or pryout strength.
calculations of all anchors, φ = 0.75 for Condition A and φ =
0.70 for Condition B.
D.4.5 — Strength reduction factor φ for anchors in RD.4.5 — As noted in R9.1, the 2002 Code incorporated
concrete shall be as follows when the load combinations the load factors of SEI/ASCE 7-02 and the corresponding
referenced in Appendix C are used: strength reduction factors provided in the 1999 Appendix C
into 9.2 and 9.3, except that the factor for flexure has been
a) Anchor governed by strength of a ductile steel increased. Developmental studies for the φ-factors to be
element used for Appendix D were based on the 1999 9.2 and 9.3
load and strength reduction factors. The resulting φ-factors
i) Tension loads............................0.80 are presented in D.4.5 for use with the load factors of
ii) Shear loads..............................0.75 Appendix C, starting with the 2002 Code. The φ-factors for
use with the load factors of the 1999 Appendix C were
b) Anchor governed by strength of a brittle steel determined in a manner consistent with the other φ-factors
D element of the 1999 Appendix C. These φ-factors are presented in
D.4.4 for use with the load factors of 9.2, starting with the
i) Tension loads............................0.70 2002 Code. Since developmental studies for φ-factors to be
ii) Shear loads..............................0.65 used with Appendix D, for brittle concrete failure modes,
were performed for the load and strength reduction factors
now given in Appendix C, the discussion of the selection of
these φ-factors appears in this section.
CODE COMMENTARY
c) Anchor governed by concrete breakout, side-face Even though the φ-factor for structural plain concrete in
blowout, pullout, or pryout strength Appendix C is 0.65, the basic factor for brittle concrete failures
(φ = 0.75) was chosen based on results of probabilistic
Condition A Condition B studiesD.17 that indicated the use of φ = 0.65 with mean
values of concrete-controlled failures produced adequate
i) Shear loads 0.85 0.75 safety levels. Because the nominal resistance expressions
ii) Tension loads used in this appendix and in the test requirements are based
on the 5 percent fractiles, the φ = 0.65 value would be overly
Cast-in headed studs, conservative. Comparison with other design procedures and
headed bolts, or hooked probabilistic studiesD.17 indicated that the choice of φ = 0.75
bolts 0.85 0.75 was justified. Applications with supplementary reinforcement
(Condition A) provide more deformation capacity, permitting
Post-installed anchors the φ-factors to be increased. The value of φ = 0.85 is
with category as determined compatible with the level of safety for shear failures in
from ACI 355.2 concrete beams, and has been recommended in the PCI
Design HandbookD.18 and by ACI 349.D.13
Category 1 0.85 0.75
(Low sensitivity
to installation and
high reliability)
D.5 — Design requirements for tensile RD.5 — Design requirements for tensile
loading loading
D.5.1 — Steel strength of anchor in tension RD.5.1 — Steel strength of anchor in tension
D.5.1.2 — The nominal strength of a single anchor RD.5.1.2 — The nominal strength of anchors in tension is
or group of anchors in tension, Nsa, shall not exceed best represented as a function of futa rather than fya because
the large majority of anchor materials do not exhibit a well-
Nsa = nAse,N futa (D-3) defined yield point. The American Institute of Steel D
Construction (AISC) has based tension strength of anchors
where n is the number of anchors in the group, Ase,N on Ase,N futa since the 1986 edition of their specifications.
is the effective cross-sectional area of a single anchor The use of Eq. (D-3) with 9.2 load factors and the φ-factors
in tension, mm2, and futa shall not be taken greater of D.4.4 give design strengths consistent with the AISC
than the smaller of 1.9fya and 860 MPa. Load and Resistance Factor Design Specifications.D.19
CODE COMMENTARY
The limitation of 1.9fya on futa is to ensure that, under
service load conditions, the anchor does not exceed fya. The
limit on futa of 1.9fya was determined by converting the
LRFD provisions to corresponding service level conditions.
For Section 9.2, the average load factor of 1.4 (from 1.2D +
1.7L) divided by the highest φ-factor (0.75 for tension)
results in a limit of futa/fya of 1.4/0.75 = 1.87. For Appendix C,
the average load factor of 1.55 (from 1.4D + 1.7L), divided
by the highest φ-factor (0.80 for tension), results in a limit
of futa/fya of 1.55/0.8 = 1.94. For consistent results, the
serviceability limitation of futa was taken as 1.9fya. If the
ratio of futa to fya exceeds this value, the anchoring may be
subjected to service loads above fya under service loads.
Although not a concern for standard structural steel anchors
(maximum value of futa/fya is 1.6 for ASTM A307), the
limitation is applicable to some stainless steels.
π 0.9743 2
A se, N = --- ⎛ d a – ----------------⎞
4⎝ nt ⎠
D.5.2 — Concrete breakout strength of anchor in RD.5.2 — Concrete breakout strength of anchor in
tension tension
D.5.2.1 — The nominal concrete breakout strength, RD.5.2.1 — The effects of multiple anchors, spacing of
Ncb or Ncbg, of a single anchor or group of anchors in anchors, and edge distance on the nominal concrete breakout
tension shall not exceed strength in tension are included by applying the modification
factors ANc /ANco and ψed,N in Eq. (D-4) and (D-5).
(a) For a single anchor
Figure RD.5.2.1(a) shows ANco and the development of
A Nc Eq. (D-6). ANco is the maximum projected area for a single
-ψ
N cb = ------------- ψ ψ N (D-4)
A Nco ed, N c, N cp, N b anchor. Figure RD.5.2.1(b) shows examples of the projected
areas for various single-anchor and multiple-anchor
(b) For a group of anchors arrangements. Because ANc is the total projected area for a
group of anchors, and ANco is the area for a single anchor,
A Nc there is no need to include n, the number of anchors, in
-ψ
N cbg = ------------- ψ ψ ψ N (D-5) Eq. (D-4) or (D-5). If anchor groups are positioned in such a
A Nco ec, N ed, N c, N cp, N b
way that their projected areas overlap, the value of ANc is
required to be reduced accordingly.
Factors ψec,N, ψed,N, ψc,N, and ψcp,N are defined in
D.5.2.4, D.5.2.5, D.5.2.6, and D.5.2.7, respectively.
ANc is the projected concrete failure area of a single
anchor or group of anchors that shall be approximated
D as the base of the rectilinear geometrical figure that
results from projecting the failure surface outward
1.5hef from the centerlines of the anchor, or in the
case of a group of anchors, from a line through a row
of adjacent anchors. ANc shall not exceed nANco ,
where n is the number of tensioned anchors in the
group. ANco is the projected concrete failure area of a
CODE COMMENTARY
Fig. RD.5.2.1—(a) Calculation of ANco; and (b) calculation of ANc for single anchors and groups of anchors.
D.5.2.2 — The basic concrete breakout strength of a RD.5.2.2 — The basic equation for anchor strength was
single anchor in tension in cracked concrete, Nb , shall derivedD.9-D.11,D.16 assuming a concrete failure prism with
not exceed an angle of about 35 degrees, considering fracture mechanics
concepts. D
Nb = kcλ f c′ hef1.5 (D-7)
The values of kc in Eq. (D-7) were determined from a large
database of test results in uncracked concreteD.9 at the 5
where percent fractile. The values were adjusted to corresponding kc
kc = 10 for cast-in anchors; and values for cracked concrete.D.10,D.20 Higher kc values for
kc = 7 for post-installed anchors. post-installed anchors may be permitted, provided they have
CODE COMMENTARY
The value of kc for post-installed anchors shall be been determined from product approval testing in accordance
permitted to be increased above 7 based on ACI 355.2 with ACI 355.2. For anchors with a deep embedment (hef >
product-specific tests, but shall in no case exceed 10. 280 mm), test evidence indicates the use of hef1.5 can be
overly conservative for some cases. Often, such tests have
Alternatively, for cast-in headed studs and headed been with selected aggregates for special applications. An
bolts with 280 mm ≤ hef ≤ 635 mm, Nb shall not exceed alternative expression (Eq. (D-8)) is provided using hef5/3 for
evaluation of cast-in anchors with 280 mm ≤ hef ≤ 635 mm.
Nb = 3.9λ f c′ hef5/3 (D-8) The limit of 635 mm corresponds to the upper range of test
data. This expression can also be appropriate for some
undercut post-installed anchors. However, for such anchors,
the use of Eq. (D-8) should be justified by test results in
accordance with D.4.2.
D.5.2.3 — Where anchors are located less than RD.5.2.3 — For anchors located less than 1.5hef from three
1.5hef from three or more edges, the value of hef used or more edges, the tensile breakout strength computed by the
in Eq. (D-4) through (D-11) shall be the greater of CCD Method, which is the basis for Eq. (D-4) to (D-11), gives
ca,max /1.5 and one-third of the maximum spacing overly conservative results.D.21 This occurs because the
between anchors within the group. ordinary definitions of ANc /ANco do not correctly reflect the
edge effects. This problem is corrected by limiting the value
of hef used in Eq. (D-4) through (D-11) to ca,max /1.5, where
ca,max is the largest of the influencing edge distances that
are less than or equal to the actual 1.5hef. In no case should
ca,max/1.5 be taken less than one-third of the maximum
spacing between anchors within the group. The limit on hef
D of at least one-third of the maximum spacing between
anchors within the group prevents the use of a calculated
strength based on individual breakout prisms for a group
anchor configuration.
CODE COMMENTARY
the computations where hef = ca,max /1.5, results in hef =
′ = 100 mm. For this example, this would be the proper
hef
value to be used for hef in computing the resistance even if
the actual embedment depth is larger.
D.5.2.4 — The modification factor for anchor groups RD.5.2.4 — Figure RD.5.2.4(a) shows a group of anchors
loaded eccentrically in tension, ψec,N , shall be that are all in tension but the resultant force is eccentric with
computed as respect to the centroid of the anchor group. Groups of
anchors can also be loaded in such a way that only some of
1 the anchors are in tension (Fig. RD.5.2.4(b)). In this case,
ψ ec, N = ---------------------------- (D-9) only the anchors in tension are to be considered in the deter-
⎛ 1 + 2e N′ ⎞
⎝
-----------
- mination of eN′ . The anchor loading has to be determined as
3h ⎠ ef the resultant anchor tension at an eccentricity with respect
to the center of gravity of the anchors in tension.
but ψec,N shall not be taken greater than 1.0.
D.5.2.5 — The modification factor for edge effects RD.5.2.5 — If anchors are located close to an edge so that
for single anchors or anchor groups loaded in tension, there is not enough space for a complete breakout prism to
ψed,N , shall be computed as develop, the strength of the anchor is further reduced
beyond that reflected in ANc /ANco. If the smallest side cover
If ca,min ≥ 1.5hef distance is greater than or equal to 1.5hef , a complete prism
can form and there is no reduction (ψed,N = 1). If the side
then ψed,N = 1.0 (D-10) cover is less than 1.5hef , the factor ψed,N is required to
adjust for the edge effect.D.9
If ca,min < 1.5hef
c a, min D
then ψed,N = 0.7 + 0.3 -----------------
- (D-11)
1.5h ef
D.5.2.6 — For anchors located in a region of a RD.5.2.6 — Post-installed and cast-in anchors that have
concrete member where analysis indicates no cracking not met the requirements for use in cracked concrete
at service load levels, the following modification factor according to ACI 355.2 should be used in uncracked regions
shall be permitted: only. The analysis for the determination of crack formation
ACI 318 Building Code and Commentary
424 APPENDIX D
CODE COMMENTARY
ψc,N = 1.25 for cast-in anchors; and
CODE COMMENTARY
installed (25 percent higher for cast-in). This agrees with
field observations and tests that show cast-in anchor
strength exceeds that of post-installed for both cracked and
uncracked concrete.
D.5.2.7 — The modification factor for post-installed RD.5.2.7 — The design provisions in D.5 are based on
anchors designed for uncracked concrete in accordance the assumption that the basic concrete breakout strength can
with D.5.2.6 without supplementary reinforcement to be achieved if the minimum edge distance, ca,min, equals
control splitting, ψcp,N, shall be computed as follows 1.5hef. However, test resultsD.22 indicate that many torque-
using the critical distance cac as defined in D.8.6 controlled and displacement-controlled expansion anchors
and some undercut anchors require minimum edge
If ca,min ≥ cac distances exceeding 1.5hef to achieve the basic concrete
breakout strength when tested in uncracked concrete
then ψcp,N = 1.0 (D-12) without supplementary reinforcement to control splitting.
When a tension load is applied, the resulting tensile stresses
If ca,min < cac at the embedded end of the anchor are added to the tensile
stresses induced due to anchor installation, and splitting
c a, min failure may occur before reaching the concrete breakout
then ψcp,N = -----------------
- (D-13) strength defined in D.5.2.1. To account for this potential
c ac
splitting mode of failure, the basic concrete breakout
strength is reduced by a factor ψcp,N if ca,min is less than the
but ψcp,N determined from Eq. (D-13) shall not be critical edge distance cac. If supplementary reinforcement to
taken less than 1.5hef /cac , where the critical distance control splitting is present or if the anchors are located in a
cac is defined in D.8.6. region where analysis indicates cracking of the concrete at
service loads, then the reduction factor ψcp,N is taken as 1.0.
For all other cases, including cast-in anchors, ψcp,N The presence of supplementary reinforcement to control
shall be taken as 1.0. splitting does not affect the selection of Condition A or B in
D.4.4 or D.4.5.
D.5.2.9 — Where anchor reinforcement is developed RD.5.2.9 — For conditions where the factored tensile
in accordance with Chapter 12 on both sides of the force exceeds the concrete breakout strength of the
breakout surface, the design strength of the anchor anchor(s) or where the breakout strength is not evaluated,
reinforcement shall be permitted to be used instead of the nominal strength can be that of anchor reinforcement
the concrete breakout strength in determining φNn. A properly anchored as illustrated in Fig. RD.5.2.9. Care
strength reduction factor of 0.75 shall be used in the needs to be taken in the selection and positioning of the
design of the anchor reinforcement. anchor reinforcement. The anchor reinforcement should
consist of stirrups, ties, or hairpins placed as close as practi-
cable to the anchor. Only reinforcement spaced less than
0.5hef from the anchor centerline should be included as
anchor reinforcement. The researchD.14 on which these D
provisions is based was limited to anchor reinforcement
with maximum diameter similar to a No. 16 bar. It is beneficial
for the anchor reinforcement to enclose the surface reinforce-
ment. In sizing the anchor reinforcement, use of a 0.75
strength reduction factor φ is recommended as is used for
CODE COMMENTARY
D.5.3 — Pullout strength of anchor in tension RD.5.3 — Pullout strength of anchor in tension
D.5.3.2 — For post-installed expansion and RD.5.3.2 — The pullout strength equations given in
undercut anchors, the values of Np shall be based on D.5.3.4 and D.5.3.5 are only applicable to cast-in headed
the 5 percent fractile of results of tests performed and and hooked anchors;D.8,D.23 they are not applicable to
evaluated according to ACI 355.2. It is not permissible expansion and undercut anchors that use various mechanisms
CODE COMMENTARY
to calculate the pullout strength in tension for such for end anchorage unless the validity of the pullout strength
anchors. equations are verified by tests.
D.5.3.3 — For single cast-in headed studs and RD.5.3.3 — The pullout strength in tension of headed
headed bolts, it shall be permitted to evaluate the studs or headed bolts can be increased by providing
pullout strength in tension using D.5.3.4. For single confining reinforcement, such as closely spaced spirals,
J- or L-bolts, it shall be permitted to evaluate the throughout the head region. This increase can be demonstrated
pullout strength in tension using D.5.3.5. Alternatively, by tests.
it shall be permitted to use values of Np based on
the 5 percent fractile of tests performed and evaluated
in the same manner as the ACI 355.2 procedures but
without the benefit of friction.
D.5.3.4 — The pullout strength in tension of a single RD.5.3.4 — The value computed from Eq. (D-15) corre-
headed stud or headed bolt, Np , for use in Eq. (D-14), sponds to the load at which crushing of the concrete occurs
shall not exceed due to bearing of the anchor head. D.8,D.13 It is not the load
required to pull the anchor completely out of the concrete,
Np = 8Abrg fc′ (D-15) so the equation contains no term relating to embedment
depth. Local crushing of the concrete greatly reduces the
stiffness of the connection, and generally will be the beginning
of a pullout failure.
D.5.3.5 — The pullout strength in tension of a single RD.5.3.5 — Equation (D-16) for hooked bolts was
hooked bolt, Np , for use in Eq. (D-14) shall not exceed developed by Lutz based on the results of Reference D.23.
Reliance is placed on the bearing component only,
Np = 0.9fc′ ehda (D-16) neglecting any frictional component because crushing
inside the hook will greatly reduce the stiffness of the
where 3da ≤ eh ≤ 4.5da. connection, and generally will be the beginning of pullout
failure. The limits on eh are based on the range of variables
used in the three tests programs reported in Reference D.23.
ψc,P = 1.4
D.5.4 — Concrete side-face blowout strength of a RD.5.4 — Concrete side-face blowout strength of a
headed anchor in tension headed anchor in tension
D.5.4.1 — For a single headed anchor with deep The design requirements for side-face blowout are based on
embedment close to an edge (hef > 2.5ca1), the the recommendations of Reference D.24. These require-
nominal side-face blowout strength, Nsb , shall not ments are applicable to headed anchors that usually are cast-
exceed in anchors. Splitting during installation rather than side-face
blowout generally governs post-installed anchors, and is
evaluated by the ACI 355.2 requirements. D
Nsb = (13ca1 A brg )λ f c′ (D-17)
CODE COMMENTARY
D.5.4.2 — For multiple headed anchors with deep RD.5.4.2 — In determining nominal side-face blowout
embedment close to an edge (hef > 2.5ca1) and strength for multiple headed anchors, only those anchors
anchor spacing less than 6ca1, the nominal strength of close to an edge (hef > 2.5ca1) that are loaded in tension
those anchors susceptible to a side-face blowout should be considered. Their strength should be compared to
failure Nsbg shall not exceed the proportion of the tensile load applied to those anchors.
Nsbg = ⎛ 1 + ------------⎞ N sb
s
(D-18)
⎝ 6c ⎠ a1
D.6 — Design requirements for shear RD.6 — Design requirements for shear
loading loading
D.6.1 — Steel strength of anchor in shear RD.6.1 — Steel strength of anchor in shear
D.6.1.2 — The nominal strength of a single anchor RD.6.1.2 — The nominal shear strength of anchors is best
or group of anchors in shear, Vsa , shall not exceed (a) represented as a function of futa rather than fya because the
through (c): large majority of anchor materials do not exhibit a well-
defined yield point. Welded studs develop a higher steel
(a) For cast-in headed stud anchor shear strength than headed anchors due to the fixity
provided by the weld between the studs and the base plate.
Vsa = nAse,V futa (D-19) The use of Eq. (D-19) and (D-20) with 9.2 load factors and
the φ-factors of D.4.4 give design strengths consistent
where n is the number of anchors in the group, Ase,V with the AISC Load and Resistance Factor Design Speci-
is the effective cross-sectional area of a single fications.D.19
anchor in shear, mm2, and futa shall not be taken
greater than the smaller of 1.9fya and 860 MPa. The limitation of 1.9fya on futa is to ensure that, under
service load conditions, the anchor stress does not exceed
(b) For cast-in headed bolt and hooked bolt anchors fya. The limit on futa of 1.9fya was determined by converting
and for post-installed anchors where sleeves do not the LRFD provisions to corresponding service level conditions
extend through the shear plane as discussed in RD.5.1.2.
Vsa = n0.6Ase,V futa (D-20) The effective cross-sectional area of an anchor should be
provided by the manufacturer of expansion anchors with
where n is the number of anchors in the group, Ase,V reduced cross-sectional area for the expansion mechanism.
is the effective cross-sectional area of a single For threaded bolts, ANSI/ASME B1.1D.1 defines Ase,V as
anchor in shear, mm2, and futa shall not be taken
greater than the smaller of 1.9fya and 860 MPa. π 0.9743 2
A se, V = --- ⎛ d a – ----------------⎞
4 ⎝ nt ⎠
(c) For post-installed anchors where sleeves extend
D through the shear plane, Vsa shall be based on the
results of tests performed and evaluated according where nt is the number of threads per mm.
to ACI 355.2. Alternatively, Eq. (D-20) shall be
permitted to be used.
CODE COMMENTARY
D.6.2 — Concrete breakout strength of anchor RD.6.2 — Concrete breakout strength of anchor
in shear in shear
D.6.2.1 — The nominal concrete breakout strength, RD.6.2.1 — The shear strength equations were developed
Vcb or Vcbg, in shear of a single anchor or group of from the CCD Method. They assume a breakout cone angle
anchors shall not exceed: of approximately 35 degrees (see Fig. RD.4.2.2(b)), and
consider fracture mechanics theory. The effects of multiple
(a) For shear force perpendicular to the edge on a anchors, spacing of anchors, edge distance, and thickness of
single anchor the concrete member on nominal concrete breakout strength
in shear are included by applying the reduction factor of
A Vc AVc /AVco in Eq. (D-21) and (D-22), and ψec,V in Eq. (D-22).
-ψ
V cb = ------------- ψ ψ V (D-21) For anchors far from the edge, D.6.2 usually will not
A Vco ed, V c, V h, V b
govern. For these cases, D.6.1 and D.6.3 often govern.
(b) For shear force perpendicular to the edge on a Figure RD.6.2.1(a) shows AVco and the development of
group of anchors Eq. (D-23). AVco is the maximum projected area for a single
anchor that approximates the surface area of the full breakout
A Vc prism or cone for an anchor unaffected by edge distance,
-ψ
V cbg = ------------- ψ ψ ψ V (D-22)
A Vco ec, V ed, V c, V h, V b spacing, or depth of member. Figure RD.6.2.1(b) shows
examples of the projected areas for various single-anchor
and multiple-anchor arrangements. AVc approximates the
(c) For shear force parallel to an edge, Vcb or Vcbg
full surface area of the breakout cone for the particular
shall be permitted to be twice the value of the shear
arrangement of anchors. Because AVc is the total projected
force determined from Eq. (D-21) or (D-22), respec-
area for a group of anchors, and AVco is the area for a single
tively, with the shear force assumed to act perpen-
anchor, there is no need to include the number of anchors in
dicular to the edge and with ψed,V taken equal to 1.0.
the equation.
(d) For anchors located at a corner, the limiting
nominal concrete breakout strength shall be deter- When using Eq. (D-22) for anchor groups loaded in shear,
mined for each edge, and the minimum value shall both assumptions for load distribution illustrated in examples
be used. on the right side of Fig. RD.6.2.1(b) should be considered
because the anchors nearest the edge could fail first or the
Factors ψec,V, ψed,V , ψc,V , and ψh,V are defined in whole group could fail as a unit with the failure surface
D.6.2.5, D.6.2.6, D.6.2.7, and D.6.2.8, respectively. Vb originating from the anchors farthest from the edge. If the
is the basic concrete breakout strength value for a anchors are welded to a common plate, when the anchor
single anchor. AVc is the projected area of the failure nearest the front edge begins to form a failure cone, shear
surface on the side of the concrete member at its edge load would be transferred to the stiffer and stronger rear
for a single anchor or a group of anchors. It shall be anchor. For this reason, anchors welded to a common plate
permitted to evaluate AVc as the base of a truncated do not need to consider the failure mode shown in the upper
half pyramid projected on the side face of the member right figure of Fig. RD.6.2.1(b). The PCI Design Handbook
where the top of the half pyramid is given by the axis of approachD.18 suggests in Section 6.5.2.2 that the strength of
the anchor row selected as critical. The value of ca1 the anchors away from the edge be considered. Because this
shall be taken as the distance from the edge to this is a reasonable approach, assuming that the anchors are
axis. AVc shall not exceed nAVco , where n is the spaced far enough apart so that the shear failure surfaces do
number of anchors in the group. not intersect,D.11 D.6.2 allows such a procedure. If the
failure surfaces do not intersect, as would generally occur if
AVco is the projected area for a single anchor in a the anchor spacing s is equal to or greater than 1.5ca1, then
deep member with a distance from edges equal or after formation of the near-edge failure surface, the higher
greater than 1.5ca1 in the direction perpendicular to strength of the farther anchor would resist most of the load.
the shear force. It shall be permitted to evaluate AVco As shown in the bottom right example in Fig. RD.6.2.1(b),
as the base of a half pyramid with a side length parallel it would be appropriate to consider the shear strength to be D
to the edge of 3ca1 and a depth of 1.5ca1 provided entirely by this anchor with its much larger
resisting failure surface. No contribution of the anchor near
AVco = 4.5(ca1)2 (D-23) the edge is then considered. Checking the near-edge anchor
condition is advisable to preclude undesirable cracking at
service load conditions. Further discussion of design for
multiple anchors is given in Reference D.8.
CODE COMMENTARY
Fig. RD.6.2.1(c)—Shear force parallel to an edge. Fig. RD.6.2.1(d)—Shear force near a corner.
D
Where anchors are located at varying distances from For the case of anchors near a corner subjected to a shear force
the edge and the anchors are welded to the attach- with components normal to each edge, a satisfactory solution is
ment so as to distribute the force to all anchors, it shall to check independently the connection for each component of
be permitted to evaluate the strength based on the the shear force. Other specialized cases, such as the shear
distance to the farthest row of anchors from the edge. resistance of anchor groups where all anchors do not have
In this case, it shall be permitted to base the value of the same edge distance, are treated in Reference D.11.
CODE COMMENTARY
ca1 on the distance from the edge to the axis of the The detailed provisions of D.6.2.1(a) apply to the case of
farthest anchor row that is selected as critical, and all shear force directed toward an edge. When the shear force is
of the shear shall be assumed to be carried by this directed away from the edge, the strength will usually be
critical anchor row alone. governed by D.6.1 or D.6.3.
D.6.2.2 — The basic concrete breakout strength in RD.6.2.2 — Like the concrete breakout tensile strength,
shear of a single anchor in cracked concrete, Vb , shall the concrete breakout shear strength does not increase with
not exceed the failure surface, which is proportional to (ca1)2. Instead,
the strength increases proportionally to (ca1)1.5 due to size
l 0.2 effect. The strength is also influenced by the anchor stiffness
V b = 0.6 ⎛ -----e-⎞
1.5
d a λ f c′ ( c a1 ) (D-24) and the anchor diameter.D.9-D.11,D.16
⎝d ⎠
a
The constant, 0.6, in the shear strength equation was deter-
where le is the load-bearing length of the anchor for shear: mined from test data reported in Reference D.9 at the 5 percent
fractile adjusted for cracking.
le = hef for anchors with a constant stiffness over the
full length of embedded section, such as headed studs
and post-installed anchors with one tubular shell over
full length of the embedment depth,
and
D.6.2.3 — For cast-in headed studs, headed bolts, RD.6.2.3 — For the case of cast-in headed bolts continu-
or hooked bolts that are continuously welded to steel ously welded to an attachment, test dataD.25 show that
attachments having a minimum thickness equal to the somewhat higher shear strength exists, possibly due to the
greater of 10 mm and half of the anchor diameter, the stiff welding connection clamping the bolt more effectively
basic concrete breakout strength in shear of a single than an attachment with an anchor gap. Because of this, the
anchor in cracked concrete, Vb , shall not exceed basic shear value for such anchors is increased. Limits are
imposed to ensure sufficient rigidity. The design of supple-
l 0.2 mentary reinforcement is discussed in References D.8,
V b = 0.66 ⎛ -----e-⎞
1.5
d a λ f c′ ( c a1 ) (D-25) D.11, and D.12.
⎝d ⎠
a
provided that:
CODE COMMENTARY
D.6.2.4 — Where anchors are influenced by three or RD.6.2.4 — For anchors influenced by three or more
more edges, the value of ca1 used in Eq. (D-23) edges where any edge distance is less than 1.5ca1, the shear
through (D-29) shall not exceed the greatest of: ca2 /1.5 in breakout strength computed by the basic CCD Method,
either direction, ha /1.5; and one-third of the maximum which is the basis for Eq. (D-21) through (D-29), gives safe
spacing between anchors within the group. but overly conservative results. These cases were studied for
the κ MethodD.16 and the problem was pointed out by
Lutz.D.21 Similarly, the approach used for tensile breakouts
in D.5.2.3, strength is correctly evaluated if the value of ca1
used in Eq. (D-21) to (D-29) is limited to the maximum of
ca2/1.5 in each direction, ha /1.5, and one-third of the
maximum spacing between anchors within the group. The
limit on ca1 of at least one-third of the maximum spacing
between anchors within the group prevents the use of a
calculated strength based on individual breakout prisms for
a group anchor configuration.
CODE COMMENTARY
(D-29) is determined when either: (a) the outer boundaries
of the failure surface first intersect a free edge; or (b) the
intersection of the breakout surface between anchors within
the group first intersects the surface of the concrete. For the
example shown in Fig. RD.6.2.4, Point “A” shows the
intersection of the assumed failure surface for limiting ca1
with the concrete surface.
D.6.2.5 — The modification factor for anchor RD.6.2.5 — This section provides a modification factor
groups loaded eccentrically in shear, ψec,V , shall be for an eccentric shear force toward an edge on a group of
computed as anchors. If the shear force originates above the plane of the
concrete surface, the shear should first be resolved as a
1 shear in the plane of the concrete surface, with a moment
ψ ec, V = ----------------------- (D-26)
2e V′ that may or may not also cause tension in the anchors,
1 + ------------ depending on the normal force. Figure RD.6.2.5 defines the
3c a1
term eV′ for calculating the ψec,V modification factor that
accounts for the fact that more shear is applied to one anchor
but ψec,V shall not be taken greater than 1.0. than others, tending to split the concrete near an edge.
If ca2 ≥ 1.5ca1
c a2
then ψed,V = 0.7 + 0.3 ----------------- (D-28)
1.5c a1
CODE COMMENTARY
D.6.2.7 — For anchors located in a region of a RD.6.2.7 — Torque-controlled and displacement-controlled
concrete member where analysis indicates no expansion anchors are permitted in cracked concrete under
cracking at service loads, the following modification pure shear loadings.
factor shall be permitted
ψc,V = 1.4
D.6.2.8 — The modification factor for anchors RD.6.2.8 — For anchors located in a concrete member
located in a concrete member where ha < 1.5ca1, ψh,V where ha < 1.5ca1, testsD.8,D.14 have shown that the concrete
shall be computed as breakout strength in shear is not directly proportional to the
member thickness ha. The factor ψh,V accounts for this effect.
1.5c a1
ψ h, V = ----------------- (D-29)
ha
D.6.2.9 — Where anchor reinforcement is either RD.6.2.9 — For conditions where the factored shear force
developed in accordance with Chapter 12 on both exceeds the concrete breakout strength of the anchor(s) in
sides of the breakout surface, or encloses the anchor shear, or where the breakout strength is not evaluated, the
and is developed beyond the breakout surface, the nominal strength can be that of anchor reinforcement properly
design strength of the anchor reinforcement shall be anchored as shown in Fig. RD.6.2.9(a) and (b). To ensure
permitted to be used instead of the concrete breakout yielding of the anchor reinforcement, the enclosing anchor
strength in determining φVn. A strength reduction reinforcement in Fig. RD.6.2.9(a) should be in contact with
factor of 0.75 shall be used in the design of the anchor the anchor and placed as close as practicable to the concrete
reinforcement. surface. The researchD.14 on which the provisions for
enclosing reinforcement (see Fig. RD.6.2.9(a)) are based
was limited to anchor reinforcement with maximum diameter
similar to a No. 16 bar. The larger bend radii associated with
larger bar diameters may significantly reduce the effectiveness
of the anchor reinforcement, and therefore anchor reinforce-
D ment with a diameter larger than No. 19 is not recommended.
CODE COMMENTARY
from the anchor centerline should be included as anchor
reinforcement. In this case, the anchor reinforcement must
be developed on both sides of the breakout surface. For
equilibrium reasons, an edge reinforcement must be present.
The research on which these provisions are based was
limited to anchor reinforcement with maximum diameter
similar to a No. 19 bar.
D.6.3 — Concrete pryout strength of anchor RD.6.3 — Concrete pryout strength of anchor
in shear in shear
D.6.3.1 — The nominal pryout strength, Vcp or Vcpg Reference D.9 indicates that the pryout shear resistance can
shall not exceed: be approximated as one to two times the anchor tensile
resistance with the lower value appropriate for hef less than
(a) For a single anchor 65 mm.
where
kcp = 1.0 for hef < 65 mm; and
kcp = 2.0 for hef ≥ 65 mm.
D.7 — Interaction of tensile and shear forces RD.7 — Interaction of tensile and shear forces
Unless determined in accordance with D.4.3, anchors The shear-tension interaction expression has traditionally
or groups of anchors that are subjected to both shear been expressed as
and axial loads shall be designed to satisfy the
requirements of D.7.1 through D.7.3. The value of φNn ς V ua⎞ ς
⎛N ua⎞
-⎠ + ⎛⎝ --------
- ≤ 1.0
shall be as required in D.4.1.2. The value of φVn shall ⎝ ---------
Nn Vn ⎠
be as defined in D.4.1.2.
D where ς varies from 1 to 2. The current trilinear recommen-
D.7.1 — If Vua ≤ 0.2φVn, then full strength in tension
shall be permitted: φNn ≥ Nua . dation is a simplification of the expression where ς = 5/3
(Fig. RD.7). The limits were chosen to eliminate the
D.7.2 — If Nua ≤ 0.2φNn, then full strength in tension requirement for computation of interaction effects where
shall be permitted: φVn ≥ Vua . very small values of the second force are present. Any other
interaction expression that is verified by test data, however,
can be used to satisfy D.4.3.
CODE COMMENTARY
D.7.3 — If Vua > 0.2φVn and Nua > 0.2φNn, then
N ua V ua
---------- + ---------- ≤ 1.2 (D-32)
φN n φV n
D.8 — Required edge distances, spacings, RD.8 — Required edge distances, spacings,
and thicknesses to preclude and thicknesses to preclude
splitting failure splitting failure
Minimum spacings and edge distances for anchors The minimum spacings, edge distances, and thicknesses are
and minimum thicknesses of members shall conform very dependent on the anchor characteristics. Installation
to D.8.1 through D.8.6, unless supplementary reinforce- forces and torques in post-installed anchors can cause split-
ment is provided to control splitting. Lesser values ting of the surrounding concrete. Such splitting also can be
from product-specific tests performed in accordance produced in subsequent torquing during connection of
with ACI 355.2 shall be permitted. attachments to anchors including cast-in anchors. The
primary source of values for minimum spacings, edge
D.8.1 — Unless determined in accordance with D.8.4, distances, and thicknesses of post-installed anchors should
minimum center-to-center spacing of anchors shall be be the product-specific tests of ACI 355.2. In some cases,
4da for untorqued cast-in anchors, and 6da for torqued however, specific products are not known in the design
cast-in anchors and post-installed anchors. stage. Approximate values are provided for use in design.
D.8.2 — Unless determined in accordance with D.8.4, RD.8.2 — Because the edge cover over a deep embedment
minimum edge distances for cast-in headed anchors close to the edge can have a significant effect on the side-
that will not be torqued shall be based on specified face blowout strength of D.5.4, in addition to the normal
cover requirements for reinforcement in 7.7. For cast- concrete cover requirements, it may be advantageous to use
in headed anchors that will be torqued, the minimum larger cover to increase the side-face blowout strength.
edge distances shall be 6da .
D.8.3 — Unless determined in accordance with D.8.4, RD.8.3 — Drilling holes for post-installed anchors can
minimum edge distances for post-installed anchors cause microcracking. The requirement for a minimum edge
shall be based on the greater of specified cover distance twice the maximum aggregate size is to minimize
requirements for reinforcement in 7.7, or minimum the effects of such microcracking.
edge distance requirements for the products as deter-
mined by tests in accordance with ACI 355.2, and shall D
not be less than 2.0 times the maximum aggregate
size. In the absence of product-specific ACI 355.2 test
information, the minimum edge distance shall be taken
as not less than:
CODE COMMENTARY
Torque-controlled anchors .................................. 8da
Displacement-controlled anchors ..................... 10da
D.8.4 — For anchors where installation does not RD.8.4 — In some cases, it may be desirable to use a larger-
produce a splitting force and that will remain untorqued, diameter anchor than the requirements on D.8.1 to D.8.3
if the edge distance or spacing is less than those speci- permit. In these cases, it is permissible to use a larger-diameter
fied in D.8.1 to D.8.3, calculations shall be performed by anchor provided the design strength of the anchor is based
substituting for da a smaller value da′ that meets the on a smaller assumed anchor diameter, da′ .
requirements of D.8.1 to D.8.3. Calculated forces
applied to the anchor shall be limited to the values
corresponding to an anchor having a diameter of da′ .
D.8.5 — The value of hef for an expansion or undercut RD.8.5 — This minimum thickness requirement is not
post-installed anchor shall not exceed the greater of applicable to through-bolts because they are outside the
2/3 of the member thickness and the member thickness scope of Appendix D. In addition, splitting failures are
minus 100 mm. caused by the load transfer between the bolt and the
concrete. Because through-bolts transfer their load differ-
ently than cast-in or expansion and undercut anchors, they
would not be subject to the same member thickness require-
ments. Post-installed anchors should not be embedded
deeper than 2/3 of the member thickness.
D.8.6 — Unless determined from tension tests in RD.8.6 — The critical edge distance cac is determined by
accordance with ACI 355.2, the critical edge distance, the corner test in ACI 355.2. Research has indicated that the
cac, shall not be taken less than: corner-test requirements are not met with ca,min = 1.5hef for
many expansion anchors and some undercut anchors
Undercut anchors ........................................... 2.5hef because installation of these types of anchors introduces
Torque-controlled anchors ................................. 4hef splitting tensile stresses in the concrete that are increased
Displacement-controlled anchors ...................... 4hef during load application, potentially resulting in a premature
splitting failure. To permit the design of these types of
anchors when product-specific information is not available,
conservative default values for cac are provided.
D.9.1 — Anchors shall be installed in accordance with Many anchor performance characteristics depend on proper
the project drawings and project specifications. installation of the anchor. Anchor strength and deformation
capacity can be assessed by acceptance testing under ACI
355.2. These tests are carried out assuming that the manu-
facturer’s installation directions will be followed. Certain
types of anchors can be sensitive to variations in hole diameter,
cleaning conditions, orientation of the axis, magnitude of
the installation torque, crack width, and other variables.
Some of this sensitivity is indirectly reflected in the
assigned φ values for the different anchor categories, which
D depend in part on the results of the installation safety tests.
Gross deviations from the ACI 355.2 acceptance testing
results could occur if anchor components are incorrectly
exchanged, or if anchor installation criteria and procedures
vary from those recommended. Project specifications
should require that anchors be installed according to the
manufacturer’s recommendations.
CODE COMMENTARY
Section Ec = w1.5
c 0.043√f ′c Ec = w1.5
c 0.14√f ′c Ec = w1.5
c 33√f ′c
8.5.1 Ec = 4700√f ′c Ec = 15,100√f ′c Ec = 57,000√f ′c
Section λ = fct /(0.56√f c′ ) ≤ 1.0 λ = fct /(1.78√f ′c ) ≤ 1.0 λ = fct /(6.7√f c′ ) ≤ 1.0
8.6.1
(1.65 – 0.0003wc) ≥ 1.09 (1.65 – 0.0003wc) ≥ 1.09 (1.65 – 0.005wc) ≥ 1.09
Table fy ⎞ fy ⎞ fy
9.5(a) ⎛ 0.4 + ---------
- ⎛ 0.4 + ------------
- ⎛ 0.4 + ----------------------
-⎞
⎝ 700⎠ ⎝ 7000⎠ ⎝ 100,000 ⎠
(9-10) fr = 0.62λ √f ′c fr = 2λ √f ′c fr = 7.5λ √f ′c
fy ⎞ fy ⎞ fy
l n ⎛ 0.8 + ------------ - l n ⎛ 0.8 + ------------------- - l n ⎛ 0.8 + ---------------------- -⎞
(9-12) ⎝ 1400⎠ ⎝ 14 ,000⎠ ⎝ 200 ,000 ⎠
h = ------------------------------------------------- ≥ 125 mm h = ------------------------------------------------- ≥ 12.5 cm h = ------------------------------------------------- ≥ 5 in.
36 + 5β ( α fm – 0.2 ) 36 + 5β ( α fm – 0.2 ) 36 + 5β ( α fm – 0.2 )
fy ⎞ fy ⎞ fy
l n ⎛ 0.8 + ------------ - l n ⎛ 0.8 + ------------------- - l n ⎛ 0.8 + ---------------------- -⎞
(9-13) ⎝ 1400⎠ ⎝ 14 ,000⎠ ⎝ 200 ,000⎠
h = --------------------------------------- ≥ 90 mm h = ---------------------------------------------- ≥ 9 cm h = ------------------------------------------------- ≥ 3.5 in.
36 + 9β 36 + 9β 36 + 9β
CODE COMMENTARY
SI-metric stress mks-metric stress U.S. Customary units stress in
in MPa in kgf/cm2 pounds per square inch (psi)
(10-17) M2,min = Pu(15 + 0.03h) M2,min = Pu(1.5 + 0.03h) M2,min = Pu(0.6 + 0.03h)
Section 2
11.1.2 f c′ ≤ 8.3 MPa f c′ ≤ 27 kgf/cm f c′ ≤ 100 psi
Nu ⎞ Nu ⎞ Nu ⎞
(11-4) Vc = 0.17 ⎛ 1 + -------------
- λ f c′ b w d Vc = 0.53 ⎛ 1 + ----------------
- λ f c′ b w d Vc = 2 ⎛ 1 + --------------------
- λ f c′ b w d
⎝ 14A g⎠ ⎝ 140A g⎠ ⎝ 2000A g⎠
V u d⎞ V u d⎞ V u d⎞
Vc = ⎛ 0.16λ fc′ + 17ρ w ----------
- b d Vc = ⎛ 0.5λ fc′ + 176ρ w ---------
- b d Vc = ⎛ 1.9λ fc′ + 2500ρ w ----------
- b d
⎝ M ⎠ w ⎝ M ⎠ w ⎝ M ⎠ w
(11-5) u u u
≤ 0.29λ f c′ b w d ≤ 0.93λ f c′ b w d ≤ 3.5λ f c′ b w d
0.29N Nu Nu
(11-7) Vc = 0.29λ f c′ b w d 1 + ------------------u- Vc = 0.93λ f c′ b w d 1 + ------------- Vc = 3.5λ f c′ b w d 1 + ----------------
-
Ag 35A g 500A g
0.29N Nu ⎞ Nu ⎞
(11-8) Vc = 0.17 ⎛ 1 + ------------------u-⎞ λ f c′ b w d ≥ 0 Vc = 0.53 ⎛ 1 + ------------- λ f c′ b w d ≥ 0 Vc = 2 ⎛ 1 + ----------------- λ f c′ b w d ≥ 0
⎝ A ⎠ ⎝ 35A ⎠ ⎝ 500A ⎠
g g g
V u d p⎞ V u d p⎞ V u d p⎞
V c = ⎛ 0.05λ f c′ + 4.8 -------------
- b d V c = ⎛ 0.16λ f c′ + 49 ------------
- b d V c = ⎛ 0.6λ f c′ + 700 -------------
- b d
⎝ M ⎠ w ⎝ M ⎠ w ⎝ M ⎠ w
u u u
(11-9)
Mcre = ⎛ ----
I ⎞ (0.5λ f ′ + f – f ) Mcre = ⎛ ---I-⎞ (1.6λ f c′ + fpe – fd) Mcre = ⎛ ----
I ⎞ (6λ f ′ + f – f )
(11-11) ⎝ y-⎠ c pe d ⎝y ⎠ ⎝ y-⎠ c pe d
t t t
bw s bw s bw s
Av,min = 0.062 f c′ ----------
- Av,min = 0.2 f c′ ---------
- Av,min = 0.75 f c′ ----------
-
f yt f yt f yt
(11-13)
bw s bw s 50b w s
≥ 0.35 ----------
- ≥ 3.5 ---------
- ≥ -----------------
-
f yt f yt f yt
2 2 2
Section ⎛ A cp⎞ ⎛ A cp⎞ ⎛ A cp⎞
11.5.1(a) Tu < φ0.083λ f c′ ⎜ ---------
-⎟ Tu < φ0.27λ f c′ ⎜ --------
-⎟ Tu < φλ f c′ ⎜ ---------
-⎟
⎝ p cp ⎠ ⎝ p cp ⎠ ⎝ p cp ⎠
2 2 2
Section ⎛ A cp⎞ f pc ⎛ A cp⎞ f pc ⎛ A cp⎞ f pc
11.5.1(b) Tu < φ0.083λ f c′ ⎜ ---------
-⎟ 1 + -------------------------
- Tu < φ0.27λ f c′ ⎜ --------
-⎟ 1 + ------------- Tu < φλ f c′ ⎜ ---------
-⎟ 1 + -----------------
-
F ⎝ cp ⎠
p 0.33λ f c′ ⎝ cp ⎠
p λ f c′ ⎝ cp ⎠
p 4λ f c′
CODE
Tu < Tu < COMMENTARY
Tu <
Section 2 2 2
⎛ A cp⎞ Nu ⎛ A cp⎞ Nu ⎛ A cp⎞ Nu
11.5.1(c) φ0.083λ f c′ ⎜ ---------
-⎟ 1 + ---------------------------------
- φ0.27λ f c′ ⎜ --------
-⎟ 1 + --------------------
- φλ f c′ ⎜ ---------
-⎟ 1 + -------------------------
⎝ cp ⎠
p 0.33A g λ f c′ ⎝ cp ⎠
p A g λ f c′ ⎝ cp ⎠
p 4A g λ f c′
2 2 2
Section ⎛ A cp⎞ ⎛ A cp⎞ ⎛ A cp⎞
11.5.2.2(a) Tu = φ0.33λ f c′ ⎜ ---------
-⎟ Tu = φλ f c′ ⎜ --------
-⎟ Tu = φ4λ f c′ ⎜ ---------
-⎟
⎝ p cp ⎠ ⎝ p cp ⎠ ⎝ p cp ⎠
2 2 2
Section ⎛ A cp⎞ f pc ⎛ A cp⎞ f pc ⎛ A cp⎞ f pc
11.5.2.2(b) Tu = φ0.33λ f c′ ⎜ ---------
-⎟ 1 + -------------------------
- Tu = φλ f c′ ⎜ --------
-⎟ 1 + ------------- Tu = φ4λ f c′ ⎜ ---------
-⎟ 1 + -----------------
-
⎝ p cp ⎠ 0.33λ f ′ c ⎝ p cp ⎠ λ f c′ ⎝ p cp ⎠ 4λ f c′
Tu = Tu = Tu =
Section 2 2 2
⎛ A cp⎞ Nu ⎛ A cp⎞ Nu ⎛ A cp⎞ Nu
11.5.2.2(c) φ0.33λ f c′ ⎜ ----------⎟ 1 + ---------------------------------
- φλ f c′ ⎜ ---------⎟ 1 + --------------------
- φ4λ f c′ ⎜ ----------⎟ 1 + -------------------------
⎝ p cp ⎠ 0.33A g λ f c′ ⎝ p cp ⎠ A g λ f c′ ⎝ p cp ⎠ 4A g λ f c′
V u ⎞ 2 ⎛ T u ph ⎞ 2
⎛ ---------- V u ⎞ 2 ⎛ T u ph ⎞ 2
⎛ --------- V u ⎞ 2 ⎛ T u ph ⎞ 2
⎛ ----------
+ ⎜ -------------------⎟ + ⎜ ------------------⎟ + ⎜ -------------------⎟
⎝ b d-⎠ ⎝ 1.7A 2 ⎠ ⎝ b d-⎠ ⎝ 1.7A 2 ⎠ ⎝ b d-⎠ ⎝ 1.7A 2 ⎠
w w w
oh oh oh
(11-18)
Vc Vc Vc
≤ φ ⎛ ----------
- + 0.66 f c′ ⎞ ≤ φ ⎛ ---------
- + 2 f c′ ⎞ ≤ φ ⎛ ----------
- + 8 f c′ ⎞
⎝b d ⎠ ⎝b d ⎠ ⎝b d ⎠
w w w
V u ⎞ ⎛ T u ph ⎞
⎛ ---------- V u ⎞ ⎛ T u ph ⎞
⎛ --------- V u ⎞ ⎛ T u ph ⎞
⎛ ----------
⎝ b d-⎠ ⎜⎝ ------------------
-⎟ ⎝ b d-⎠ ⎜⎝ -----------------
-⎟ ⎝ b d-⎠ ⎜⎝ ------------------
-⎟
+ + +
1.7A oh⎠ 1.7A oh⎠ 1.7A oh⎠
2 2 2
w w w
(11-19)
Vc Vc Vc
≤ φ ⎛ ----------
- + 0.66 f c′ ⎞ ≤ φ ⎛ ---------
- + 2 f c′ ⎞ ≤ φ ⎛ ----------
- + 8 f c′ ⎞
⎝b d ⎠ ⎝b d ⎠ ⎝b d ⎠
w w w
bw s bw s bw s
(Av + 2At) = 0.062 f c′ ----------
- (Av + 2At) = 0.2 f c′ ---------
- (Av + 2At) = 0.75 f c′ ----------
-
f yt f yt f yt
(11-23)
0.35b w s 3.5b w s 50b w s
≥ ----------------------
- ≥ ------------------ ≥ -----------------
-
f yt f yt f yt
0.42 f c′ A cp ⎛ A t⎞ f yt 1.33 f c′ A cp ⎛ A t⎞ f yt 5 f c′ A cp ⎛ A t⎞ f yt
- – ------ p h ------
Al,min = -------------------------------- - – ----- p h -----
Al,min = ------------------------------- - – ------ p h ------
Al,min = ------------------------
fy ⎝ s⎠ fy fy ⎝ s⎠ f fy ⎝ s⎠ fy
y
(11-24)
A t 0.175b w A t 1.75b w A t 25b w
------ ≥ ---------------------- ----- ≥ ------------------ ------ ≥ --------------
s f yt s f yt s f yt
(3.3 + 0.08fc′)Ac (34 + 0.08fc′)Ac (480 + 0.08fc′)Ac
Section 11Ac 110Ac 1600Ac
11.6.5
5.5Ac 55Ac 800Ac
Section
11.7.3 0.83 f c′ bwd 2.65 f c′ bwd 10 f c′ bwd
CODE COMMENTARY
SI-metric stress mks-metric stress U.S. Customary units stress in
in MPa in kgf/cm2 pounds per square inch (psi)
Nu d Nu d Nu d
(11-27) Vc = 0.27λ f c′ hd + ----------
- Vc = 0.88λ f c′ hd + ---------- Vc = 3.3λ f c′ hd + ----------
-
4l w 4l w 4l w
⎛ 0.2N ⎞
u ⎛ 0.2N ⎞
u ⎛ 0.2N ⎞
u
l ⎜ 0.1λ f ′ + -----------------⎟ l ⎜ 0.33λ f ′ + ----------------⎟ l ⎜ 1.25λ f ′ + -----------------⎟
w⎝ c l h ⎠ w⎝ c l h ⎠ w⎝ c l h ⎠
w w w
(11-28) Vc = 0.05λ f c′ + ------------------------------------------------------------ hd Vc = 0.16λ f c′ + -------------------------------------------------------------- hd Vc = 0.6λ f c′ + ---------------------------------------------------------------- hd
Mu l Mu l Mu l
w w w
-------- – ------ -------- – ------ -------- – ------
V V V
u 2 u 2 u 2
(11-33) Vc = 0.33λ f c′ b o d Vc = λ f c′ b o d Vc = 4λ f c′ b o d
Section ⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞
ld = ⎜ ----------------------
-⎟ d b ld = ⎜ ---------------------
-⎟ d b ld = ⎜ --------------------
-⎟ d b
12.2.2 ⎝ 2.1λ f c′ ⎠ ⎝ 6.6λ f c′ ⎠ ⎝ 25λ f c′ ⎠
Section ⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞
ld = ⎜ ----------------------
-⎟ d b ld = ⎜ ---------------------
-⎟ d b ld = ⎜ --------------------
-⎟ d b
12.2.2 ⎝ 1.7λ f c′ ⎠ ⎝ 5.3λ f c′ ⎠ ⎝ 20λ f c′ ⎠
Section ⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞ ⎛ 3f y ψ t ψ e⎞
ld = ⎜ ----------------------
-⎟ d b ld = ⎜ ---------------------
-⎟ d b ld = ⎜ ---------------------
-⎟ d b
12.2.2 ⎝ 1.4λ f c′ ⎠ ⎝ 4.4λ f c′ ⎠ ⎝ 50λ f c′ ⎠
Section ⎛ fy ψt ψe ⎞ ⎛ fy ψt ψe ⎞ ⎛ 3f y ψ t ψ e⎞
F ld = ⎜ ----------------------
-⎟ d b ld = ⎜ ---------------------
-⎟ d b ld = ⎜ ---------------------
-⎟ d b
12.2.2 ⎝ 1.1λ f c′ ⎠ ⎝ 3.5λ f c′ ⎠ ⎝ 40λ f c′ ⎠
CODE ψt ψe ψs ψt ψe ψs
COMMENTARYψψ
fy fy 3f y t e ψs
- --------------------------d
ld = ---------------------- b - ------------------------
ld = --------------------- - db - --------------------------d
ld = -------------------- b
(12-1) 1.1λ f c′ ⎛ c b + K tr⎞ 3.5λ f c′ ⎛ c b + K tr⎞ 40λ f c′ ⎛ c b + K tr⎞
⎝ d--------------------
- ⎠ ⎝ ------------------ -⎠ ⎝ d--------------------
- ⎠
b d b b
Section ⎛ f--------------------
y – 240⎞ ⎛ f----------------------
y – 2460⎞ f y – 35, 000 ⎞
⎛ -------------------------------
⎝ f ⎠ ⎝ -⎠ ⎝ -⎠
12.7.2 y f
y fy
A ⎛ fy ⎞ A ⎛ fy ⎞ A ⎛ fy ⎞
l d = 3.3 ⎛ ------b-⎞ ⎜ ------------- l d = ⎛ ------b⎞ ⎜ ------------- l d = 0.27 ⎛ ------b-⎞ ⎜ -------------
(12-3) ⎝ s ⎠ ⎝ λ f ′-⎟⎠ ⎝ s ⎠ ⎝ λ f ′ ⎟⎠ ⎝ s ⎠ ⎝ λ f ′-⎟⎠
c c c
f se⎞ f –f f se ⎞ f –f f se ⎞ f –f
(12-4) l d = ⎛ ------ d + ⎛ ps se⎞ d b l d = ⎛ --------- d + ⎛ ps se-⎞ d b l d = ⎛ ------------ d + ⎛ ps se⎞ d b
⎝ 21-⎠ b ⎝ ---------------------
7 ⎠ ⎝ 210-⎠ b ⎝ -------------------
70 ⎠ ⎝ 3000-⎠ b ⎝ ---------------------
1000 ⎠
Section bw s bw s bw s
0.41 ----------
- 4.2 ---------
- 60 ----------
-
12.10.5.2 f yt f yt f yt
Section (b) Class T : 0.62 f c′ < ft ≤ 1.0 f c′ (b) Class T : 2 f c′ < ft ≤ 3.2 f c′ (b) Class T : 7.5 f c′ < ft ≤ 12 f c′
18.3.3
(c) Class C : ft > 1.0 f c′ (c) Class C : ft > 3.2 f c′ (c) Class C : ft > 12 f c′
ft ≤ 0.50 f ci
′ ft ≤ 1.6 f ci′ ft ≤ 6 f ci
′
Section ′
0.50 f ci 1.6 f ci′ ′
6 f ci
18.4.1(c) ′
0.25 f ci 0.8 f ci′ ′
3 f ci
f c′ f c′ f c′
(18-4) fps = fse + 70 + ---------------
- fps = fse + 700 + ---------------
- fps = fse + 10,000 + ---------------
-
100ρ p 100ρ p 100ρ p
f c′ f c′ f c′
(18-5) fps = fse + 70 + ---------------
- fps = fse + 700 + ---------------
- fps = fse + 10,000 + ---------------
-
300ρ p 300ρ p 300ρ p
Section F
18.9.3.1
and 0.17 f c′ 0.53 f c′ 2 f c′
18.9.3.2
CODE COMMENTARY
SI-metric stress mks-metric stress U.S. Customary units stress in
in MPa in kgf/cm2 pounds per square inch (psi)
350 – h 35 – h 14 – h
so = 100 ⎛ ---------------------x-⎞ so = 10 ⎛ -----------------x-⎞ so = 4 ⎛ ------------------x-⎞
⎝ 3 ⎠ ⎝ 3 ⎠ ⎝ 3 ⎠
(21-2)
100 mm ≤ so ≤ 150 mm 10 cm ≤ so ≤ 15 cm 4 in. ≤ so ≤ 6 in.
1.7 f c′ Aj 5.3 f c′ Aj 20 f c′ Aj
Section
21.7.4.1 1.2 f c′ Aj 4 f c′ Aj 15 f c′ Aj
1.0 f c′ Aj 3.2 f c′ Aj 12 f c′ Aj
fy db fy db fy db
(21-6) ldh = ------------------
- ldh = ---------------------
- ldh = -----------------
5.4 f c′ 17.2 f c′ 65 f c′
Section
21.9.2.1 0.083Acvλ f c′ 0.27Acvλ f c′ Acvλ f c′
Section
21.9.2.2 0.17Acvλ f c′ 0.53Acvλ f c′ 2Acvλ f c′
hw hw hw
αc = 0.25 for ------
- ≤ 1.5 αc = 0.80 for ------ ≤ 1.5 αc = 3.0 for ------
- ≤ 1.5
(21-7) lw lw lw
hw hw hw
αc = 0.17 for ------
- ≥ 2.0 αc = 0.53 for ------ ≥ 2.0 αc = 2.0 for ------
- ≥ 2.0
lw lw lw
(21-9) Vn = 2Avd fy sinα ≤ 0.83 f c′ Acw Vn = 2Avd fy sinα ≤ 2.65 f c′ Acw Vn = 2Avd fy sinα ≤ 10 f c′ Acw
CODE COMMENTARY
SI-metric stress mks-metric stress U.S. Customary units stress in
in MPa in kgf/cm2 pounds per square inch (psi)
M P M P M P
(22-7) -------u- – ------u- ≤ φ0.42λ f c′ -------u- – ------u ≤ φ1.33λ f c′ -------u- – ------u- ≤ φ5λ f c′
Sm Ag Sm Ag Sm Ag
4λ f c′
(22-9) Vn = 0.11λ f c′ bw h Vn = 0.35λ f c′ bw h Vn = -----------------
- bw h
3
2
V n = 0.35 1 + 2 4 8
V n = 0.11 1 + --- λ f c′ b o h --- λ f c′ b o h Vn = --- + ------ λ f c′ b o h
β β 3 3β
(22-10)
≤ 0.22 λ f c′ b o h ≤ 0.71 λ f c′ b o h ≤ 2.66 λ f c′ b o h
0.85β 1 fc′ ⎛ 600 ⎞ 0.85β 1 fc′ ⎛ 6120 ⎞ 0.85β 1 fc′ ⎛ 87, 000 ⎞
(B-1) ρ b = ------------------------
- --------------------- ρ b = -----------------------
- ------------------------ ρ b = ------------------------
- -------------------------------
fy ⎝ 600 + f ⎠ fy ⎝ 6120 + f ⎠ fy ⎝ 87, 000 + f ⎠
y y y
1.5 1.5 1.5
Nb = kcλ f c′ hef Nb = kcλ f c′ hef Nb = kcλ f c′ hef
(D-7)
kc = 10 or 7 kc = 10 or 7 kc = 24 or 17
5/3 5/3 5/3
(D-8) Nb = 3.9λ fc′ hef Nb = 5.8λ fc′ hef Nb = 16λ fc′ hef
(D-17) Nsb = 13ca1 A brg λ fc′ Nsb = 42.5ca1 A brg λ fc′ Nsb = 160ca1 A brg λ fc′
CODE COMMENTARY
COMMENTARY REFERENCES
1.3. ACI Committee 313, “Standard Practice for Design and 1.19. Uniform Building Code, V. 2, Structural Engineering Design
Construction of Concrete Silos and Stacking Tubes for Storing Provisions, 1997 Edition, International Conference of Building
Granular Materials (ACI 313-97),” American Concrete Institute, Officials, Whittier, CA, 1997, 492 pp.
Farmington Hills, MI, 1997, 19 pp.
1.20. “NEHRP Recommended Provisions for Seismic Regulations
1.4. ACI Committee 349, “Code Requirements for Nuclear Safety- for New Buildings and Other Structures,” Part 1: Provisions, and
Related Concrete Structures (ACI 349-06) and Commentary,” Part 2: Commentary (FEMA 450), Building Seismic Safety
American Concrete Institute, Farmington Hills, MI, 2006, 153 pp. Council, Washington D.C., 2004.
1.5. Joint ACI-ASME Committee 359, “Code for Concrete 1.21. ACI Committee 350, “Code Requirements for Environmental
Containments (ACI 359-01),” American Concrete Institute, Farm- Engineering Concrete Structures (ACI 350-06) and Commentary,”
ington Hills, MI, 2001. American Concrete Institute, Farmington Hills, MI, 2006, 486 pp.
1.6. ACI Committee 543, “Design, Manufacture, and Installation 1.22. ACI Committee 311, “Guide for Concrete Inspection (ACI
of Concrete Piles (ACI 543R-00) (Reapproved 2005),” American 311.4R-05),” American Concrete Institute, Farmington Hills, MI,
Concrete Institute, Farmington Hills, MI, 2000, 49 pp. 2005, 13 pp.
1.7. ACI Committee 336, “Design and Construction of Drilled 1.23. ACI Committee 311, ACI Manual of Concrete Inspection,
Piers (ACI 336.3R-93) (Reapproved 1998),” American Concrete SP-2, 9th Edition, American Concrete Institute, Farmington Hills,
Institute, Farmington Hills, MI, 1993, 30 pp. MI, 1999, 209 pp.
1.8. “Recommended Practice for Design, Manufacture, and Instal- References, Chapter 3
lation of Prestressed Concrete Piling,” PCI Journal, V. 38, No. 2,
3.1. ACI Committee 214, “Evaluation of Strength Test Results of
Mar.-Apr. 1993, pp. 14-41.
Concrete (ACI 214R-02),” American Concrete Institute, Farm-
ington Hills, MI, 2002, 20 pp.
1.9. ACI Committee 360, “Design of Slabs-on Ground (ACI 360R-
06),” American Concrete Institute, Farmington Hills, MI, 2006, 74 pp.
3.2 ACI Committee 440, “Guide for the Design and Construction
of Structural Concrete Reinforced with FRP Bars (ACI 440.1R-06),”
1.10. PTI, “Design of Post-Tensioned Slabs-on-Ground,” 3rd American Concrete Institute, Farmington Hills, MI, 44 pp.
Edition, Post-Tensioning Institute, Phoenix, AZ, 2004, 106 pp.
3.3 ACI Committee 440, “Guide for the Design and Construction
1.11. ANSI/ASCE 3-91, “Standard for the Structural Design of of Externally Bonded FRP Systems for Strengthening of Concrete
Composite Slabs,” ASCE, Reston, VA, 1994. Structures (ACI 440.2R-02),” American Concrete Institute, Farm-
ington Hills, MI, 45 pp.
1.12. ANSI/ASCE 9-91, “Standard Practice for the Construction
and Inspection of Composite Slabs,” American Society of Civil 3.4. Gustafson, D. P., and Felder, A. L., “Questions and Answers
Engineers, Reston, VA, 1994. on ASTM A 706 Reinforcing Bars,” Concrete International, V. 13,
No. 7, July 1991, pp. 54-57.
1.13. “Design Manual for Composite Decks, Form Decks and Roof
Decks,” Publication No. 30, Steel Deck Institute, Fox River Grove, 3.5. Rutledge, S., and DeVries, R. A., “Development of D45
IL, 2000, 48 pp. Wire in Concrete,” Report, School of Civil and Environmental
Engineering, Oklahoma State University, Stillwater, OK, Jan.
1.14. “Minimum Design Loads for Buildings and Other Structures 2002, 28 pp.
(ASCE/SEI 7-05),” ASCE, Reston, VA, 2005.
3.6. Parra-Montesinos, G. J., “Shear Strength of Beams with
1.15. “International Building Code,” International Code Council, Deformed Steel Fibers,” Concrete International, V. 28, No. 11,
Falls Church, VA, 2006. Nov. 2006, pp. 57-66.
3.7. ACI Committee 223, “Standard Practice for the Use of 5.2 ACI Committee 211, “Standard Practice for Selecting Propor-
Shrinkage-Compensating Concrete (ACI 223-98),” American tions for Structural Lightweight Concrete (ACI 211.2-98) (Reap-
Concrete Institute, Farmington Hills, MI, 26 pp. proved 2004),” American Concrete Institute, Farmington Hills, MI,
1998, 20 pp.
References, Chapter 4
5.3. ASTM C1077-07, “Standard Practice for Laboratories Testing
4.1. Li, S., and Roy, D. M., “Investigation of Relations between Concrete and Concrete Aggregates for Use in Construction and
Porosity, Pore Structure and CL Diffusion of Fly Ash and Blended Criteria for Laboratory Evaluation,” ASTM, West Conshohocken,
Cement Pastes,” Cement and Concrete Research, V. 16, No. 5, PA, 2007, 6 pp.
Sept. 1986, pp. 749-759.
5.4. ASTM D3665-07, “Standard Practice for Random Sampling
4.3. ACI Committee 233, “Slag Cement in Concrete and Mortar of Construction Materials,” ASTM, West Conshohocken, PA,
(ACI 233R-03),” American Concrete Institute, Farmington Hills, 2007, 13 pp.
MI, 2003, 19 pp.
5.5. ACI Committee 214, “Evaluation of Strength Test Results of
4.2. ACI Committee 234, “Guide for the Use of Silica Fume in Concrete (ACI 214R-02),” American Concrete Institute, Farmington
Concrete (ACI 234R-06),” American Concrete Institute, Farmington Hills, MI, 2002, 20 pp.
Hills, MI, 2006, 63 pp.
5.6. Carino, N. J.; Guthrie, W. F.; Lagergren, E. S.; and Mullings,
4.4. Ozyildirim, C., and Halstead, W., “Resistance to Chloride Ion G. M., “Effects of Testing Variables on the Strength of High-
Penetration of Concretes Containing Fly Ash, Silica Fume, or Strength (90 MPa) Concrete Cylinders,” High-Performance
Slag,” Permeability of Concrete, SP-108, American Concrete Insti- Concrete, SP-149, V. M. Malhotra, ed., American Concrete Institute,
tute, Farmington Hills, MI, 1988, pp. 35-61. Farmington Hills, MI, 1994, pp. 589-632.
4.5. ASTM C1202-05, “Standard Test Method for Electrical Indi- 5.7. Bloem, D. L., “Concrete Strength Measurement—Cores vs.
cation of Concrete’s Ability to Resist Chloride Ion Penetration,” Cylinders,” Proceedings, ASTM, V. 65, 1965, pp. 668-696.
ASTM Book of Standards, Part 04.02, ASTM, West Conshohocken,
PA, 2005, 6 pp. 5.8. Bloem, D. L., “Concrete Strength in Structures,” ACI
JOURNAL, Proceedings V. 65, No. 3, Mar. 1968, pp. 176-187.
4.6. ACI Committee 201, “Guide to Durable Concrete (ACI
201.2R-01),” American Concrete Institute, Farmington Hills, MI, 5.9. Malhotra, V. M., Testing Hardened Concrete: Nondestructive
2001, 41 pp. Methods, ACI Monograph No. 9, American Concrete Institute/
Iowa State University Press, Farmington Hills, MI, 1976, 188 pp.
4.7. ACI Committee 222, “Protection of Metals in Concrete
Against Corrosion (ACI 222R-01),” American Concrete Institute, 5.10. Malhotra, V. M., “Contract Strength Requirements—Cores
Farmington Hills, MI, 2001, 41 pp. Versus In Situ Evaluation,” ACI JOURNAL, Proceedings V. 74, No. 4,
Apr. 1977, pp. 163-172.
4.8. ACI Committee 222, “Provisional Standard Test Method for
Water-Soluble Chloride Available for Corrosion of Embedded Steel 5.11. Bartlett, M. F., and MacGregor, J. G., “Effect of Moisture
in Mortar and Concrete Using the Soxhlet Extractor (ACI 222.1-96),” Condition on Concrete Core Strengths,” ACI Materials Journal,
American Concrete Institute, Farmington Hills, MI, 3 pp. V. 91, No. 3, May-June 1994, pp. 227-236.
4.9. ACI Committee 211, “Standard Practice for Selecting Propor- 5.12. Chen, L.; Mindess, S.; Morgan, D. R.; Shah, S. P.; Johnston,
tions for Normal, Heavyweight, and Mass Concrete (ACI 211.1-91) C. D.; and Pigeon, M., “Comparative Toughness Testing of Fiber
(Reapproved 2002),” American Concrete Institute, Farmington Reinforced Concrete,” Testing of Fiber Reinforced Concrete, SP-155,
Hills, MI, 1991, 38 pp. American Concrete Institute, Farmington Hills, MI, 1995, pp. 41-69.
4.10. Drahushak-Crow, R., “Freeze-Thaw Durability of Fly Ash 5.13. ACI Committee 304, “Guide for Measuring, Mixing, Trans-
Concrete,” EPRI Proceedings, Eighth International Ash Utilization porting, and Placing Concrete (ACI 304R-00),” American Concrete
Symposium, V. 2, Oct. 1987, p. 37-1. Institute, Farmington Hills, MI, 2000, 41 pp.
4.11. Whiting, D., “Deicer Scaling and Resistance of Lean 5.14. Newlon, H., Jr., and Ozol, A., “Delayed Expansion of
Concretes Containing Fly Ash,” Fly Ash, Silica Fume, Slag, and Concrete Delivered by Pumping through Aluminum Pipe Line,”
Natural Pozzolans in Concrete, SP-114, American Concrete Insti- Concrete Case Study No. 20, Virginia Highway Research Council,
tute, Farmington Hills, MI, 1989, pp. 349-372. Oct. 1969, 39 pp.
References, Chapter 5 5.15. ACI Committee 309, “Guide for Consolidation of Concrete
(ACI 309R-05),” American Concrete Institute, Farmington Hills,
5.1. ACI Committee 211, “Standard Practice for Selecting Propor- MI, 2005, 36 pp.
tions for Normal, Heavyweight, and Mass Concrete (ACI 211.1-91)
(Reapproved 2002),” American Concrete Institute, Farmington 5.16. ACI Committee 308, “Guide to Curing Concrete (ACI 308R-01),”
Hills, MI, 1991, 38 pp. American Concrete Institute, Farmington Hills, MI, 2001, 31 pp.
5.17. ACI Committee 306, “Cold Weather Concreting (ACI 306R-88) 7.6. ACI Committee 117, “Specifications for Tolerances for Concrete
(Reapproved 2002),” American Concrete Institute, Farmington Construction and Materials and Commentary (ACI 117-06),”
Hills, MI, 1988, 23 pp. American Concrete Institute, Farmington Hills, MI, 70 pp.
5.18. ACI Committee 305, “Hot Weather Concreting (ACI 305R-99),” 7.7. PCI Design Handbook: Precast and Prestressed Concrete, 6th
American Concrete Institute, Farmington Hills, MI, 1999, 20 pp. Edition, MNL-120-4, Precast/Prestressed Concrete Institute, Chicago,
IL, 2004, 736 pp.
References, Chapter 6
7.8. ACI Committee 408, “Bond Stress—The State of the Art,” ACI
6.1. ACI Committee 347, “Guide to Formwork for Concrete (ACI JOURNAL, Proceedings V. 63, No. 11, Nov. 1966, pp. 1161-1188.
347-04),” American Concrete Institute, Farmington Hills, MI,
2004, 32 pp. 7.9. “Standard Specifications for Highway Bridges,” 15th Edition,
American Association of State Highway and Transportation Officials,
6.2. Hurd, M. K., and ACI Committee 347, Formwork for Washington, D.C., 1992, 686 pp.
Concrete, SP-4, 7th Edition, American Concrete Institute, Farm-
ington Hills, MI, 2005, 500 pp. 7.10. Deatherage, J. H.; Burdette, E. G.; and Chew, C. K., “Develop-
ment Length and Lateral Spacing Requirements of Prestressing Strand
6.3. Liu, X. L.; Lee, H. M.; and Chen, W. F., “Shoring and for Prestressed Concrete Bridge Girders,” PCI Journal, V. 39, No. 1,
Reshoring of High-Rise Buildings,” Concrete International, V. 10, Jan.-Feb. 1994, pp. 70-83.
No. 1, Jan. 1989, pp. 64-68.
7.11. Russell, B. W., and Burns, N. H. “Measured Transfer Lengths of
6.4. ASTM C873-04, “Standard Test Method for Compressive 0.5 and 0.6 in. Strands in Pretensioned Concrete,” PCI Journal, V. 41,
Strength of Concrete Cylinders Cast in Place in Cylindrical No. 5, Sept.-Oct. 1996, pp. 44-65.
Molds,” ASTM, West Conshohocken, PA, 2004, 4 pp.
7.12. ACI Committee 362, “Guide for the Design of Durable Parking
6.5. ASTM C803/C803M-03, “Standard Test Method for Penetration Structures (ACI 362.1R-97) (Reapproved 2002),” American Concrete
Resistance of Hardened Concrete,” ASTM, West Conshohocken, Institute, Farmington Hills, MI, 1997, 33 pp.
PA, 2003, 5 pp.
7.13. Hanson, N. W., and Conner, H. W., “Seismic Resistance
6.6. ASTM C900-06, “Standard Test Method for Pullout Strength of of Reinforced Concrete Beam-Column Joints,” Proceedings, ASCE,
Hardened Concrete,” ASTM, West Conshohocken, PA, 2006, 10 pp. V. 93, No. ST5, Oct. 1967, pp. 533-560.
6.7. ASTM C1074-04, “Standard Practice for Estimating Concrete 7.14. Joint ACI-ASCE Committee 352, “Recommendations for
Strength by the Maturity Method,” ASTM, West Conshohocken, Design of Beam-Column Connections in Monolithic Reinforced
PA, 2004, 9 pp. Concrete Structures (ACI 352R-02),” American Concrete Institute,
Farmington Hills, MI, 2002, 37 pp.
6.8. “Power Piping (ANSI/ASME B 31.1-1992),” American
Society of Mechanical Engineers, New York, 1992. 7.15. Pfister, J. F., “Influence of Ties on the Behavior of Reinforced
Concrete Columns,” ACI JOURNAL, Proceedings V. 61, No. 5, May
6.9. “Chemical Plant and Petroleum Refinery Piping (ANSI/ 1964, pp. 521-537.
ASME B 31.3-1990),” American Society of Mechanical Engi-
neers, New York, 1990. 7.16. Gilbert, R. I., “Shrinkage Cracking in Fully Restrained Concrete
Members,” ACI Structural Journal, V. 89, No. 2, Mar.-Apr.
References, Chapter 7 1992, pp. 141-149.
7.1. ACI Committee 315, ACI Detailing Manual—2004, SP-66, 7.17. “Design and Typical Details of Connections for Precast and
American Concrete Institute, Farmington Hills, MI, 2004, 212 pp. Prestressed Concrete,” MNL-123-88, Precast/Prestressed Concrete
Institute, Chicago, IL, 1988, 270 pp.
7.2. Black, W. C., “Field Corrections to Partially Embedded Rein-
forcing Bars,” ACI JOURNAL, Proceedings V. 70, No. 10, Oct. 7.18. PCI Building Code Committee, “Proposed Design
1973, pp. 690-691. Requirements for Precast Concrete,” PCI Journal, V. 31, No. 6, Nov.-
Dec. 1986, pp. 32-47.
7.3. Stecich, J.; Hanson, J. M.; and Rice, P. F.; “Bending and
Straightening of Grade 60 Reinforcing Bars,” Concrete Interna- References, Chapter 8
tional: Design & Construction, V. 6, No. 8, Aug. 1984, pp. 14-23.
8.1. “Minimum Design Loads for Buildings and Other Structures
7.4. Kemp, E. L.; Brezny, F. S.; and Unterspan, J. A., “Effect of (ASCE/SEI 7-05),” ASCE, Reston, VA, 2005.
Rust and Scale on the Bond Characteristics of Deformed Reinforcing
Bars,” ACI JOURNAL, Proceedings V. 65, No. 9, Sept. 1968, 8.2. Fintel, M.; Ghosh, S. K.; and Iyengar, H., Column Shortening
pp. 743-756. in Tall Buildings—Prediction and Compensation, EB108D, Portland
Cement Association, Skokie, IL, 1986, 34 pp.
7.5. Sason, A. S., “Evaluation of Degree of Rusting on Prestressed
Concrete Strand,” PCI Journal, V. 37, No. 3, May-June 1992, pp. 25-30. 8.3. Bondy, K. B., “Moment Redistribution—Principles and Prac-
tice Using ACI 318-02,” PTI Journal, V. 1, No. 1, Post-Tensioning 9.2. “International Building Code,” International Code Council,
Institute, Phoenix, AZ, Jan. 2003, pp. 3-21. Falls Church, VA, 2003.
8.4. Cohn, M. Z., “Rotational Compatibility in the Limit Design 9.3. “Minimum Design Loads for Buildings and Other Structures
of Reinforced Concrete Continuous Beams,” Flexural Mechanics (ASCE 7-93),” ASCE, New York, 1993, 134 pp.
of Reinforced Concrete, SP-12, American Concrete Institute/
American Society of Civil Engineers, Farmington Hills, MI, 9.4. “BOCA National Building Code,” 13th Edition, Building Offi-
1965, pp. 359-382. cials and Code Administration International, Inc., Country Club
Hills, IL, 1993, 357 pp.
8.5. Mattock, A. H., “Redistribution of Design Bending Moments
in Reinforced Concrete Continuous Beams,” Proceedings, Insti- 9.5. “Standard Building Code,” Southern Building Code Congress
tution of Civil Engineers (London), V. 13, 1959, pp. 35-46. International, Inc., Birmingham, AL, 1994, 656 pp.
8.6. Mast, R. F., “Unified Design Provision for Reinforced and 9.6. “Uniform Building Code, V. 2, Structural Engineering Design
Prestressed Concrete Flexural and Compression Members,” ACI Provisions,” International Conference of Building Officials,
Structural Journal, V. 89, No. 2, Mar.-Apr. 1992, pp. 185-199. Whittier, CA, 1997, 492 pp.
8.7. Pauw, A., “Static Modulus of Elasticity of Concrete as 9.7. MacGregor, J. G., “Safety and Limit States Design for
Affected by Density,” ACI JOURNAL, Proceedings V. 57, No. 6, Reinforced Concrete,” Canadian Journal of Civil Engineering, V. 3,
Dec. 1960, pp. 679-687. No. 4, Dec. 1976, pp. 484-513.
8.8. ASTM C469-02ε1, “Standard Test Method for Static Modulus 9.8. Winter, G., “Safety and Serviceability Provisions in the ACI
of Elasticity and Poisson’s Ratio of Concrete in Compression,” Building Code,” Concrete Design: U.S. and European Practices,
ASTM, West Conshohocken, PA, 2002, 5 pp. SP-59, American Concrete Institute, Farmington Hills, MI, 1979,
pp. 35-49.
8.9. Ivey, D. L., and Buth, E., “Shear Capacity of Lightweight
Concrete Beams,” ACI JOURNAL, Proceedings V. 64, No. 10, Oct. 9.9. Nowak, A. S., and Szerszen, M. M., “Reliability-Based Cali-
1967, pp. 634-643. bration for Structural Concrete,” Report UMCEE 01-04, Depart-
ment of Civil and Environmental Engineering, University of
8.10. Hanson, J. A., “Tensile Strength and Diagonal Tension Resis- Michigan, Ann Arbor, MI, Nov. 2001.
tance of Structural Lightweight Concrete,” ACI JOURNAL,
Proceedings V. 58, No. 1, July 1961, pp. 1-40. 9.10. Nowak, A. S.; Szerszen, M. M.; Szeliga, E. K.; Szwed, A.;
and Podhorecki, P. J., “Reliability-Based Calibration for Structural
8.11. Handbook of Frame Constants, Portland Cement Associa- Concrete,” Report No. UNLCE 05-03, University of Nebraska,
tion, Skokie, IL, 1972, 34 pp. Lincoln, NE, Oct. 2005.
8.12. Moehle, J. P., “Displacement-Based Design of RC Structures 9.11. Mlakar, P. F., ed., “Special Section: Performance of the
Subjected to Earthquakes,” Earthquake Spectra, V. 8, No. 3, Aug. Pentagon: Terrorist Attack of September 11, 2001,” Journal of
1992, pp. 403-428. Performance of Constructed Facilities, V. 19, Issue 3, Aug. 2005,
pp. 187-221. (a collection of five papers)
8.13. Lepage, A., “Nonlinear Drift of Multistory RC Structures
9.12. Mast, R. F., “Unified Design Provision for Reinforced and
during Earthquakes,” Sixth National Conference on Earthquake
Prestressed Concrete Flexural and Compression Members,” ACI
Engineering, Seattle, WA, 1998.
Structural Journal, V. 89, No. 2, Mar.-Apr. 1992, pp. 185-199.
8.14. Vanderbilt, M. D., and Corley, W. G., “Frame Analysis of
9.13. Deflections of Concrete Structures, SP-43, American
Concrete Building,” Concrete International, V. 5, No. 12, Dec.
Concrete Institute, Farmington Hills, MI, 1974, 637 pp.
1983, pp. 33-43.
9.14. ACI Committee 213, “Guide for Structural Lightweight
8.15. Hwang, S., and Moehle, J. P., “Models for Laterally Loaded Aggregate Concrete (ACI 213R-03),” American Concrete Institute,
Slab-Column Frames,” ACI Structural Journal, V. 97, No. 2, Mar.- Farmington Hills, MI, 2003, 38 pp.
Apr. 2000, pp. 345-353.
9.15. Branson, D. E., “Instantaneous and Time-Dependent Deflec-
8.16. Dovich, L. M., and Wight, J. K., “Effective Slab Width tions on Simple and Continuous Reinforced Concrete Beams,”
Model for Seismic Analysis of Flat Slab Frames,” ACI Structural HPR Report No. 7, Part 1, Alabama Highway Department, Bureau
Journal, V. 102, No. 6, Nov.-Dec. 2005, pp. 868-875. of Public Roads, Aug. 1965, pp. 1-78.
8.17. “Continuity in Concrete Building Frames,” Portland Cement 9.16. ACI Committee 435, “Deflections of Reinforced Concrete
Association, Skokie, IL, 1959, 56 pp. Flexural Members (ACI 435.2R-66),” ACI JOURNAL, Proceedings
V. 63, No. 6, June 1966, pp. 637-674.
References, Chapter 9
9.17. Subcommittee 1, ACI Committee 435, “Allowable Deflec-
9.1. “Minimum Design Loads for Buildings and Other Structures,” tions (ACI 435.3R-68),” ACI JOURNAL, Proceedings V. 65, No. 6,
SEI/ASCE 7-02, ASCE, Reston, VA, 2002, 376 pp. June 1968, pp. 433-444.
9.18. ACI Committee 209, “Prediction of Creep, Shrinkage, and Concrete Stress Distribution in Ultimate Strength Design,” ACI
Temperature Effects in Concrete Structures (ACI 209R-92) (Reap- JOURNAL, Proceedings V. 57, No. 8, Feb. 1961, pp. 875-928.
proved 1997),” American Concrete Institute, Farmington Hills, MI,
1992, 48 pp. 10.4. ACI Committee 340, ACI Design Handbook (ACI 340R-97),
SP-17(97), American Concrete Institute, Farmington Hills, MI,
9.19. ACI Committee 435, “Deflections of Continuous Concrete 1997, 482 pp.
Beams (ACI 435.5R-73) (Reapproved 1989),” American Concrete
Institute, Farmington Hills, MI, 1973, 7 pp. 10.5. CRSI Handbook, 9th Edition, Concrete Reinforcing Steel
Institute, Schaumburg, IL, 2002, 648 pp.
9.20. ACI Committee 435, “Proposed Revisions by Committee 435
to ACI Building Code and Commentary Provisions on Deflections,” 10.6. Bresler, B., “Design Criteria for Reinforced Concrete
ACI JOURNAL, Proceedings V. 75, No. 6, June 1978, pp. 229-238. Columns under Axial Load and Biaxial Bending,” ACI JOURNAL,
Proceedings V. 57, No. 5, Nov. 1960, pp. 481-490.
9.21. Branson, D. E., “Compression Steel Effect on Long-Time
Deflections,” ACI JOURNAL, Proceedings V. 68, No. 8, Aug. 1971, 10.7. Parme, A. L.; Nieves, J. M.; and Gouwens, A., “Capacity of
pp. 555-559. Reinforced Rectangular Columns Subjected to Biaxial Bending,”
ACI JOURNAL, Proceedings V. 63, No. 9, Sept. 1966, pp. 911-923.
9.22. Branson, D. E., Deformation of Concrete Structures,
McGraw-Hill Book Co., New York, 1977, 546 pp. 10.8. Heimdahl, P. D., and Bianchini, A. C., “Ultimate Strength of
Biaxially Eccentrically Loaded Concrete Columns Reinforced with
9.23. PCI Design Handbook: Precast and Prestressed Concrete, High Strength Steel,” Reinforced Concrete Columns, SP-50, Amer-
6th Edition, MNL-120-04, Precast/Prestressed Concrete Institute, ican Concrete Institute, Farmington Hills, MI, 1975, pp. 100-101.
Chicago, IL, 2004, pp. 4-68 to 4-72.
10.9. Furlong, R. W., “Concrete Columns Under Biaxially Eccentric
9.24. Mast, R. F., “Analysis of Cracked Prestressed Concrete Thrust,” ACI JOURNAL, Proceedings V. 76, No. 10, Oct. 1979,
Sections: A Practical Approach,” PCI Journal, V. 43, No. 4, July- pp. 1093-1118.
Aug. 1998, pp. 80-91.
10.10. Hansell, W., and Winter, G., “Lateral Stability of Reinforced
9.25. Shaikh, A. F., and Branson, D. E., “Non-Tensioned Steel in Concrete Beams,” ACI JOURNAL, Proceedings V. 56, No. 3, Sept.
Prestressed Concrete Beams,” Journal of the Prestressed Concrete 1959, pp. 193-214.
Institute, V. 15, No. 1, Feb. 1970, pp. 14-36.
10.11. Sant, J. K., and Bletzacker, R. W., “Experimental Study of
9.26. Branson, D. E., discussion of “Proposed Revision of ACI Lateral Stability of Reinforced Concrete Beams,” ACI JOURNAL,
318-63: Building Code Requirements for Reinforced Concrete,” by Proceedings V. 58, No. 6, Dec. 1961, pp. 713-736.
ACI Committee 318, ACI JOURNAL, Proceedings V. 67, No. 9,
Sept. 1970, pp. 692-695. 10.12. Gergely, P., and Lutz, L. A., “Maximum Crack Width in
Reinforced Concrete Flexural Members,” Causes, Mechanism, and
9.27. Subcommittee 5, ACI Committee 435, “Deflections of Control of Cracking in Concrete, SP-20, American Concrete Insti-
Prestressed Concrete Members (ACI 435.1R-63),” ACI JOURNAL, tute, Farmington Hills, MI, 1968, pp. 87-117.
Proceedings V. 60, No. 12, Dec. 1963, pp. 1697-1728.
10.13. Kaar, P. H., “High Strength Bars as Concrete Reinforce-
9.28. Branson, D. E.; Meyers, B. L.; and Kripanarayanan, K. M., ment, Part 8: Similitude in Flexural Cracking of T-Beam Flanges,”
“Time-Dependent Deformation of Noncomposite and Composite Journal, PCA Research and Development Laboratories, V. 8, No. 2,
Prestressed Concrete Structures,” Symposium on Concrete Defor- May 1966, pp. 2-12.
mation, Highway Research Record 324, Highway Research Board,
1970, pp. 15-43. 10.14. Base, G. D.; Reed, J. B.; Beeby, A. W.; and Taylor, H. P. J.,
“An Investigation of the Crack Control Characteristics of Various
9.29. Ghali, A., and Favre, R., Concrete Structures: Stresses and Types of Bar in Reinforced Concrete Beams,” Research Report
Deformations, Chapman and Hall, New York, 1986, 348 pp. No. 18, Cement and Concrete Association, London, Dec. 1966, 44 pp.
References, Chapter 10 10.15. Beeby, A. W., “The Prediction of Crack Widths in Hardened
Concrete,” The Structural Engineer, V. 57A, No. 1, Jan. 1979, pp. 9-17.
10.1. Leslie, K. E.; Rajagopalan, K. S.; and Everard, N. J., “Flexural
Behavior of High-Strength Concrete Beams,” ACI JOURNAL, 10.16. Frosch, R. J., “Another Look at Cracking and Crack Control
Proceedings V. 73, No. 9, Sept. 1976, pp. 517-521. in Reinforced Concrete,” ACI Structural Journal, V. 96, No. 3,
May-June 1999, pp. 437-442.
10.2. Karr, P. H.; Hanson, N. W; and Capell, H. T.; “Stress-Strain
Characteristics of High Strength Concrete,” Douglas McHenry 10.17. ACI Committee 318, “Closure to Public Comments on ACI
International Symposium on Concrete and Concrete Structures, 318-99,” Concrete International, V. 21, No. 5, May 1999, pp. 318-1
SP-55, American Concrete Institute, Farmington Hills, MI, 1978, to 318-50.
pp. 161-185.
10.18. Darwin, D. et al., “Debate: Crack Width, Cover, and Corro-
10.3. Mattock, A. H.; Kriz, L. B.; and Hognestad, E., “Rectangular sion,” Concrete International, V. 7, No. 5, May 1985, pp. 20-35.
10.19. Oesterle, R. G., “The Role of Concrete Cover in Crack 10.35. MacGregor, J. G., and Hage, S. E., “Stability Analysis and
Control Criteria and Corrosion Protection,” RD Serial No. 2054, Design Concrete,” Proceedings, ASCE, V. 103, No. ST 10, Oct.
Portland Cement Association, Skokie, IL, 1997. 1977.
10.20. Frantz, G. C., and Breen, J. E., “Cracking on the Side Faces 10.36. “Minimum Design Loads for Buildings and Other Struc-
of Large Reinforced Concrete Beams,” ACI JOURNAL, Proceedings tures (ASCE/SEI 7-05),” ASCE, Reston, VA, 2005.
V. 77, No. 5, Sept.-Oct. 1980, pp. 307-313.
10.37. Grossman, J. S., “Slender Concrete Structures—The New
10.21. Frosch, R. J., “Modeling and Control of Side Face Beam Edge,” ACI Structural Journal, V. 87, No. 1, Jan.-Feb. 1990,
Cracking,” ACI Structural Journal, V. 99, No. 3, May-June 2002, pp. 39-52.
pp. 376-385.
10.38. Grossman, J. S., “Reinforced Concrete Design,” Building
10.22. Chow, L.; Conway, H.; and Winter, G., “Stresses in Deep Structural Design Handbook, R. N. White and C. G. Salmon, eds.,
Beams,” Transactions, ASCE, V. 118, 1953, pp. 686-708. John Wiley and Sons, New York, 1987.
10.23. “Design of Deep Girders,” IS079D, Portland Cement Asso- 10.39. Khuntia, M., and Ghosh, S. K., “Flexural Stiffness of
ciation, Skokie, IL, 1946, 10 pp. Reinforced Concrete Columns and Beams: Analytical Approach,”
ACI Structural Journal, V. 101, No. 3, May-June 2004, pp. 351-363.
10.24. Park, R., and Paulay, T., Reinforced Concrete Structures,
Wiley-Interscience, New York, 1975, 769 pp. 10.40. Khuntia, M., and Ghosh, S. K., “Flexural Stiffness of
Reinforced Concrete Columns and Beams: Experimental Verification,”
10.25. Furlong, R. W., “Column Slenderness and Charts for Design,” ACI Structural Journal, V. 101, No. 3, May-June 2004, pp. 364-374.
ACI JOURNAL, Proceedings V. 68, No. 1, Jan. 1971, pp. 9-18.
10.41. Mirza, S. A.; Lee, P. M.; and Morgan, D. L., “ACI Stability
Resistance Factor for RC Columns,” Journal of Structural Engi-
10.26. “Reinforced Concrete Column Investigation—Tentative
neering, ASCE, V. 113, No. 9, Sept. 1987, pp. 1963-1976.
Final Report of Committee 105,” ACI JOURNAL, Proceedings V. 29,
No. 5, Feb. 1933, pp. 275-282.
10.42. Mirza, S. A., “Flexural Stiffness of Rectangular Reinforced
Concrete Columns,” ACI Structural Journal, V. 87, No. 4, July-
10.27. Saatcioglu, M., and Razvi, S. R., “Displacement-Based
Aug. 1990, pp. 425-435.
Design of Reinforced Concrete Columns for Confinement,” ACI
Structural Journal, V. 99, No. 1, Jan.-Feb. 2002, pp. 3-11.
10.43. Lai, S. M. A., and MacGregor, J. G., “Geometric Nonlinearities
in Unbraced Multistory Frames,” Journal of Structural Engineering,
10.28. Pessiki, S.; Graybeal, B.; and Mudlock, M., “Proposed
ASCE, V. 109, No. 11, Nov. 1983, pp. 2528-2545.
Design of High-Strength Spiral Reinforcement in Compression
Members,” ACI Structural Journal, V. 98, No. 6, Nov.-Dec. 2001,
10.44. Bianchini, A. C.; Woods, R. E.; and Kesler, C. E., “Effect of
pp. 799-810.
Floor Concrete Strength on Column Strength,” ACI JOURNAL,
Proceedings V. 56, No. 11, May 1960, pp. 1149-1169.
10.29. Richart, F. E.; Brandzaeg, A.; and Brown, R. L., “The
Failure of Plain and Spirally Reinforced Concrete in Compression,”
10.45. Ospina, C. E., and Alexander, S. D. B., “Transmission of
Bulletin No. 190, University of Illinois Engineering Experiment
Interior Concrete Column Loads through Floors,” Journal of Struc-
Station, Apr. 1929, 74 pp.
tural Engineering, ASCE, V. 124, No. 6., June 1998, pp. 602-610.
10.30. “Guide to Design Criteria for Metal Compression 10.46. Tikka, T. K., and Mirza, S. A., “Nonlinear Equation for
Members,” 2nd Edition, Column Research Council, Fritz Engineering Flexural Stiffness of Slender Composite Columns in Major Axis
Laboratory, Lehigh University, Bethlehem, PA, 1966. Bending,” Journal of Structural Engineering, ASCE, V. 132, No. 3,
Mar. 2006, pp. 387-399.
10.31. MacGregor, J. G.; Breen, J. E.; and Pfrang, E. O., “Design
of Slender Concrete Columns,” ACI JOURNAL, Proceedings V. 67, 10.47. Hawkins, N. M., “Bearing Strength of Concrete Loaded
No. 1, Jan. 1970, pp. 6-28. through Rigid Plates,” Magazine of Concrete Research (London),
V. 20, No. 62, Mar. 1968, pp. 31-40.
10.32. MacGregor, J. G., “Design of Slender Concrete Columns—
Revisited,” ACI Structural Journal, V. 90, No. 3, May-June 1993,
References, Chapter 11
pp. 302-309.
11.1. Joint ACI-ASCE Committee 426, “Shear Strength of
10.33. Ford, J. S.; Chang, D. C.; and Breen, J. E., “Design Indica- Reinforced Concrete Members (ACI 426R-74),” Proceedings,
tions from Tests of Unbraced Multipanel Concrete Frames,” ASCE, V. 99, No. ST6, June 1973, pp. 1148-1157.
Concrete International: Design and Construction, V. 3, No. 3,
Mar. 1981, pp. 37-47. 11.2. MacGregor, J. G., and Hanson, J. M., “Proposed Changes in
Shear Provisions for Reinforced and Prestressed Concrete Beams,”
10.34. Wilson, E. L., “Three-Dimensional Dynamic Analysis of ACI JOURNAL, Proceedings V. 66, No. 4, Apr. 1969, pp. 276-288.
Structures—With Emphasis on Earthquake Engineering,”
Computers and Structures, Inc., Berkeley, CA, 1997. 11.3. Joint ACI-ASCE Committee 326 (now 426), “Shear and
Diagonal Tension,” ACI JOURNAL, Proceedings V. 59, No. 1, Jan. Joint-Shear Provisions for Interior Beam-Column-Slab Connec-
1962, pp. 1-30; No. 2, Feb. 1962, pp. 277-334; and No. 3, Mar. tions Using High Strength Materials,” ACI Structural Journal,
1962, pp. 352-396. V. 89, No. 1, Jan.-Feb. 1992, pp. 89-98.
11.4. Barney, G. B.; Corley, W. G.; Hanson, J. M.; and Parmelee, 11.19. Griezic, A.; Cook, W. D.; and Mitchell, D., “Tests to Deter-
R. A., “Behavior and Design of Prestressed Concrete Beams with mine Performance of Deformed Welded-Wire Fabric Stirrups,”
Large Web Openings,” Journal of the Prestressed Concrete Institute, ACI Structural Journal, V. 91, No. 2, Mar.-Apr. 1994, pp. 211-220.
V. 22, No. 6, Nov.-Dec. 1977, pp. 32-61.
11.20. Furlong, R. W.; Fenves, G. L.; and Kasl, E. P., “Welded
11.5. Schlaich, J.; Schafer, K.; and Jennewein, M., “Toward a Structural Wire Reinforcement for Columns,” ACI Structural
Consistent Design of Structural Concrete,” Journal of the Prestressed Journal, V. 88, No. 5, Sept.-Oct. 1991, pp. 585-591.
Concrete Institute, V. 32, No. 3, May-June 1987, pp. 74-150.
11.21. Angelakos, D.; Bentz, E. C.; and Collins, M. D., “Effect of
11.6. Joint Committee, “Recommended Practice and Standard Concrete Strength and Minimum Stirrups on Shear Strength of
Specification for Concrete and Reinforced Concrete,” Proceedings, Large Members,” ACI Structural Journal, V. 98, No. 3, May-June
ASCE, V. 66, No. 6, Part 2, June 1940, 81 pp. 2001, pp. 290-300.
11.7. Mphonde, A. G., and Frantz, G. C., “Shear Tests of High- 11.22. Lubell, A. S.; Sherwood, E. G.; Bentz, E. C.; and Collins,
and Low-Strength Concrete Beams without Stirrups,” ACI M. P., “Safe Shear Design of Large Wide Beams,” Concrete
JOURNAL, Proceedings V. 81, No. 4, July-Aug. 1984, pp. 350-357. International, V. 26, No. 1, Jan. 2004, pp. 66-78.
11.8. Elzanaty, A. H.; Nilson, A. H.; and Slate, F. O., “Shear 11.23. Brown, M. D.; Bayrak, O.; and Jirsa, J. O., “Design for
Capacity of Reinforced Concrete Beams Using High Strength Shear Based on Loading Conditions,” ACI Structural Journal, V. 103,
Concrete,” ACI JOURNAL, Proceedings V. 83, No. 2, Mar.-Apr. No. 4, July-Aug. 2006, pp. 541-550.
1986, pp. 290-296.
11.24. Becker, R. J., and Buettner, D. R., “Shear Tests of Extruded
11.9. Roller, J. J., and Russell, H. G., “Shear Strength of High- Hollow Core Slabs,” PCI Journal, V. 30, No. 2, Mar.-Apr. 1985.
Strength Concrete Beams with Web Reinforcement,” ACI Struc-
tural Journal, V. 87, No. 2, Mar.-Apr. 1990, pp. 191-198. 11.25. Anderson, A. R., “Shear Strength of Hollow Core
Members,” Technical Bulletin 78-81, Concrete Technology
11.10. Johnson, M. K., and Ramirez, J. A., “Minimum Amount of Associates, Tacoma, WA, Apr. 1978, 33 pp.
Shear Reinforcement in High Strength Concrete Members,” ACI
Structural Journal, V. 86, No. 4, July-Aug. 1989, pp. 376-382. 11.26. Hawkins, N. M., and Ghosh, S. K., “Shear Strength of
Hollow Core Slabs,” PCI Journal, V. 51, No. 1, Jan.-Feb. 2006,
11.11. Ozcebe, G.; Ersoy, U.; and Tankut, T., “Evaluation of pp. 110-114.
Minimum Shear Reinforcement for Higher Strength Concrete,” ACI
Structural Journal, V. 96, No. 3, May-June 1999, pp. 361-368. 11.27. Parra-Montesinos, G. J., “Shear Strength of Beams with
Deformed Steel Fibers,” Concrete International, V. 28, No. 11,
11.12. Kani, G. N. J., “Basic Facts Concerning Shear Failure,” ACI Nov. 2006, pp. 57-66.
JOURNAL, Proceedings V. 63, No. 6, June 1966, pp. 675-692.
11.28. Olesen, S. E.; Sozen, M. A.; and Siess, C. P., “Investigation
11.13. Kani, G. N. J., “How Safe Are Our Large Reinforced of Prestressed Reinforced Concrete for Highway Bridges, Part IV:
Concrete Beams,” ACI JOURNAL, Proceedings V. 64, No. 3, Mar. Strength in Shear of Beams with Web Reinforcement,” Bulletin
1967, pp. 128-141. No. 493, Engineering Experiment Station, University of Illinois,
Urbana, IL, 1967.
11.14. Faradji, M. J., and Diaz de Cossio, R., “Diagonal Tension in
Concrete Members of Circular Section” (in Spanish) Institut de 11.29. Anderson, N. S., and Ramirez, J. A., “Detailing of Stirrup
Ingenieria, Mexico (translation by Portland Cement Association, Reinforcement,” ACI Structural Journal, V. 86, No. 5, Sept.-Oct.
Foreign Literature Study No. 466). 1989, pp. 507-515.
11.15. Khalifa, J. U., and Collins, M. P., “Circular Reinforced 11.30. Leonhardt, F., and Walther, R., “The Stuttgart Shear Tests,”
Concrete Members Subjected to Shear,” Publications No. 81-08, C&CA Translation, No. 111, Cement and Concrete Association,
Department of Civil Engineering, University of Toronto, Dec. 1981. London, 1964, 134 pp.
11.16. PCI Design Handbook: Precast and Prestressed Concrete, 11.31. MacGregor, J. G., and Ghoneim, M. G., “Design for Torsion,”
6th Edition, MNL-120-4, Precast/Prestressed Concrete Institute, ACI Structural Journal, V. 92, No. 2, Mar.-Apr. 1995, pp. 211-218.
Chicago, IL, 2004, 736 pp.
11.32. Hsu, T. T. C., “ACI Shear and Torsion Provisions for
11.17. ACI Committee 318, “Commentary on Building Code Prestressed Hollow Girders,” ACI Structural Journal, V. 94, No. 6,
Requirements for Reinforced Concrete (ACI 318-63),” SP-10, Nov.-Dec. 1997, pp. 787-799.
American Concrete Institute, Farmington Hills, MI, 1965, pp. 78-84.
11.33. Hsu, T. T. C., “Torsion of Structural Concrete—Behavior of
11.18. Guimares, G. N.; Kreger, M. E.; and Jirsa, J. O., “Evaluation of Reinforced Concrete Rectangular Members,” Torsion of Structural
Concrete, SP-18, American Concrete Institute, Farmington Hills, American Institute of Steel Construction, Chicago, IL, Sept. 1986,
MI, 1968, pp. 291-306. pp. 51-58.
11.34. Collins, M. P., and Lampert, P., “Redistribution of Moments 11.49. Kahn, L. F., and Mitchell, A. D., “Shear Friction Tests with
at Cracking—The Key to Simpler Torsion Design?” Analysis of High-Strength Concrete,” ACI Structural Journal, V. 99, No. 1,
Structural Systems for Torsion, SP-35, American Concrete Insti- Jan.-Feb. 2002, pp. 98-103.
tute, Farmington Hills, MI, 1973, pp. 343-383.
11.50. Mattock, A. H., “Shear Friction and High-Strength
11.35. Hsu, T. T. C., and Burton, K. T., “Design of Reinforced Concrete,” ACI Structural Journal, V. 98, No. 1, Jan.-Feb. 2001,
Concrete Spandrel Beams,” Proceedings, ASCE, V. 100, No. ST1, pp. 50-59.
Jan. 1974, pp. 209-229.
11.51. Mattock, A. H.; Johal, L.; and Chow, H. C., “Shear Transfer
11.36. Hsu, T. C., “Shear Flow Zone in Torsion of Reinforced in Reinforced Concrete with Moment or Tension Acting Across
Concrete,” Journal of Structural Engineering, ASCE, V. 116, No. 11, the Shear Plane,” Journal of the Prestressed Concrete Institute,
Nov. 1990, pp. 3206-3226. V. 20, No. 4, July-Aug. 1975, pp. 76-93.
11.37. Mitchell, D., and Collins, M. P., “Detailing for Torsion,” 11.52. Rogowsky, D. M., and MacGregor, J. G., “Design of
ACI JOURNAL, Proceedings V. 73, No. 9, Sept. 1976, pp. 506-511. Reinforced Concrete Deep Beams,” Concrete International, V. 8,
No. 8, Aug. 1986, pp. 46-58.
11.38. Behera, U., and Rajagopalan, K. S., “Two-Piece U-Stirrups
in Reinforced Concrete Beams,” ACI JOURNAL, Proceedings V. 66, 11.53. Marti, P., “Basic Tools of Reinforced Concrete Beam
No. 7, July 1969, pp. 522-524. Design,” ACI JOURNAL, Proceedings V. 82, No. 1, Jan.-Feb. 1985,
pp. 46-56.
11.39. Zia, P., and McGee, W. D., “Torsion Design of Prestressed
Concrete,” PCI Journal, V. 19, No. 2, Mar.-Apr. 1974. 11.54. Crist, R. A., “Shear Behavior of Deep Reinforced Concrete
Beams,” Proceedings, Symposium on the Effects of Repeated
11.40. Zia, P., and Hsu, T. T. C., “Design for Torsion and Shear in Loading of Materials and Structural Elements (Mexico City,
Prestressed Concrete Flexural Members,” PCI Journal, V. 49, No. 3, 1966), V. 4, RILEM, Paris, 31 pp.
May-June 2004.
11.55. Kriz, L. B., and Raths, C. H., “Connections in Precast
11.41. Collins, M. P., and Mitchell, D., “Shear and Torsion Design Concrete Structures—Strength of Corbels,” Journal of the
of Prestressed and Non-Prestressed Concrete Beams,” PCI Prestressed Concrete Institute, V. 10, No. 1, Feb. 1965, pp. 16-47.
Journal, V. 25, No. 4, Sept.-Oct. 1980.
11.56. Mattock, A. H.; Chen, K. C.; and Soongswang, K., “The
11.42. Klein, G. J., “Design of Spandrel Beams,” PCI Specially Behavior of Reinforced Concrete Corbels,” Journal of the
Funded Research Project No. 5, Precast/Prestressed Concrete Prestressed Concrete Institute, V. 21, No. 2, Mar.-Apr. 1976,
Institute, Chicago, IL, 1986. pp. 52-77.
11.43. Birkeland, P. W., and Birkeland, H. W., “Connections in 11.57. Cardenas, A. E.; Hanson, J. M.; Corley, W. G.; and
Precast Concrete Construction,” ACI JOURNAL, Proceedings V. 63, Hognestad, E., “Design Provisions for Shear Walls,” ACI
No. 3, Mar. 1966, pp. 345-368. JOURNAL, Proceedings V. 70, No. 3, Mar. 1973, pp. 221-230.
11.44. Mattock, A. H., and Hawkins, N. M., “Shear Transfer in 11.58. Barda, F.; Hanson, J. M.; and Corley, W. G., “Shear
Reinforced Concrete—Recent Research,” Journal of the Prestressed Strength of Low-Rise Walls with Boundary Elements,” Reinforced
Concrete Institute, V. 17, No. 2, Mar.-Apr. 1972, pp. 55-75. Concrete Structures in Seismic Zones, SP-53, American Concrete
Institute, Farmington Hills, MI, 1977, pp. 149-202.
11.45. Mattock, A. H.; Li, W. K.; and Want, T. C., “Shear Transfer
in Lightweight Reinforced Concrete,” Journal of the Prestressed 11.59. Hanson, N. W., and Conner, H. W., “Seismic Resistance of
Concrete Institute, V. 21, No. 1, Jan.-Feb. 1976, pp. 20-39. Reinforced Concrete Beam-Column Joints,” Proceedings, ASCE,
V. 93, No. ST5, Oct. 1967, pp. 533-560.
11.46. Mattock, A. H., “Shear Transfer in Concrete Having Rein-
forcement at an Angle to the Shear Plane,” Shear in Reinforced 11.60. Joint ACI-ASCE Committee 352, “Recommendations for
Concrete, SP-42, American Concrete Institute, Farmington Hills, Design of Beam-Column Connections in Monolithic Reinforced
MI, 1974, pp. 17-42. Concrete Structures (ACI 352R-02),” American Concrete Institute,
Farmington Hills, MI, 2002, 37 pp.
11.47. Mattock, A. H., discussion of “Considerations for the
Design of Precast Concrete Bearing Wall Buildings to Withstand 11.61. Joint ACI-ASCE Committee 426, “The Shear Strength of
Abnormal Loads,” by PCI Committee on Precast Concrete Bearing Reinforced Concrete Members-Slabs,” Proceedings, ASCE, V. 100,
Wall Buildings, Journal of the Prestressed Concrete Institute, V. 22, No. ST8, Aug. 1974, pp. 1543-1591.
No. 3, May-June 1977, pp. 105-106.
11.62. Vanderbilt, M. D., “Shear Strength of Continuous Plates,”
11.48. “Chapter 1—Composite Members,” Load and Resistance Journal of the Structural Division, ASCE, V. 98, No. ST5, May
Factor Design Specification for Structural Steel for Buildings, 1972, pp. 961-973.
11.63. Joint ACI-ASCE Committee 423, “Recommendations for Development Length of Reinforcing Bars Embedded in High-
Concrete Members Prestressed with Unbonded Tendons (ACI Strength Concrete,” Engineering Structures, V. 17, No. 7, 1995,
423.3R-05),” American Concrete Institute, Farmington Hills, MI, pp. 512-522.
2005, 25 pp.
12.5. Jirsa, J. O., and Breen, J. E., “Influence of Casting Position
11.64. Burns, N. H., and Hemakom, R., “Test of Scale Model of and Shear on Development and Splice Length—Design Recom-
Post-Tensioned Flat Plate,” Proceedings, ASCE, V. 103, No. ST6, mendations,” Research Report 242-3F, Center for Transportation
June 1977, pp. 1237-1255. Research, Bureau of Engineering Research, University of Texas at
Austin, Nov. 1981.
11.65. Hawkins, N. M., “Shear Strength of Slabs with Shear
Reinforcement,” Shear in Reinforced Concrete, SP-42, V. 2, Amer- 12.6. Jeanty, P. R.; Mitchell, D.; and Mirza, M. S., “Investigation of
ican Concrete Institute, Farmington Hills, MI, 1974, pp. 785-815. ‘Top Bar’ Effects in Beams,” ACI Structural Journal V. 85, No. 3,
May-June 1988, pp. 251-257.
11.66. Broms, C. E., “Shear Reinforcement for Deflection
Ductility of Flat Plates,” ACI Structural Journal, V. 87, No. 6, 12.7. Treece, R. A., and Jirsa, J. O., “Bond Strength of Epoxy-
Nov.-Dec. 1990, pp. 696-705. Coated Reinforcing Bars,” ACI Materials Journal, V. 86, No. 2,
Mar.-Apr. 1989, pp. 167-174.
11.67. Yamada, T.; Nanni, A.; and Endo, K., “Punching Shear Resis-
tance of Flat Slabs: Influence of Reinforcement Type and Ratio,” ACI 12.8. Johnston, D. W., and Zia, P., “Bond Characteristics of Epoxy-
Structural Journal, V. 88, No. 4, July-Aug. 1991, pp. 555-563. Coated Reinforcing Bars,” Report No. FHWA/NC/82-002, Depart-
ment of Civil Engineering, North Carolina State University,
11.68. Hawkins, N. M.; Mitchell, D.; and Hannah, S. N., “The Raleigh, NC, Aug. 1982.
Effects of Shear Reinforcement on Reversed Cyclic Loading
Behavior of Flat Plate Structures,” Canadian Journal of Civil 12.9. Mathey, R. G., and Clifton, J. R., “Bond of Coated Reinforcing
Engineering (Ottawa), V. 2, 1975, pp. 572-582. Bars in Concrete,” Journal of the Structural Division, ASCE, V. 102,
No. ST1, Jan. 1976, pp. 215-228.
11.69. Joint ACI-ASCE Committee 421, “Shear Reinforcement for
Slabs (ACI 421.1R-99) (Reapproved 2006),” American Concrete 12.10. Orangun, C. O.; Jirsa, J. O.; and Breen, J. E., “A Reevalua-
Institute, Farmington Hills, MI, 1999, 15 pp. tion of Test Data on Development Length and Splices,” ACI
JOURNAL, Proceedings V. 74, No. 3, Mar. 1977, pp. 114-122.
11.70. Corley, W. G., and Hawkins. N. M., “Shearhead Reinforce-
ment for Slabs,” ACI JOURNAL, Proceedings V. 65, No. 10, Oct. 12.11. Azizinamini, A.; Pavel, R.; Hatfield, E.; and Ghosh, S. K.,
1968, pp. 811-824. “Behavior of Spliced Reinforcing Bars Embedded in High-
Strength Concrete,” ACI Structural Journal, V. 96, No. 5, Sept.-
11.71. Hanson, N. W., and Hanson, J. M., “Shear and Moment Transfer Oct. 1999, pp. 826-835.
between Concrete Slabs and Columns,” Journal, PCA Research
and Development Laboratories, V. 10, No. 1, Jan. 1968, pp. 2-16. 12.12. Azizinamini, A.; Darwin, D.; Eligehausen, R.; Pavel, R.;
and Ghosh, S. K., “Proposed Modifications to ACI 318-95 Devel-
11.72. Hawkins, N. M., “Lateral Load Resistance of Unbonded Post- opment and Splice Provisions for High-Strength Concrete,” ACI
Tensioned Flat Plate Construction,” Journal of the Prestressed Structural Journal, V. 96, No. 6, Nov.-Dec. 1999, pp. 922-926.
Concrete Institute, V. 26, No. 1, Jan.-Feb. 1981, pp. 94-115.
12.13. Jirsa, J. O., and Marques, J. L. G., “A Study of Hooked Bar
11.73. Hawkins, N. M., and Corley, W. G., “Moment Transfer to Anchorages in Beam-Column Joints,” ACI JOURNAL, Proceedings
Columns in Slabs with Shearhead Reinforcement,” Shear in V. 72, No. 5, May 1975, pp. 198-200.
Reinforced Concrete, SP-42, American Concrete Institute, Farm-
ington Hills, MI, 1974, pp. 847-879. 12.14. Hamad, B. S.; Jirsa, J. O.; and D’Abreu, N. I., “Anchorage
Strength of Epoxy-Coated Hooked Bars,” ACI Structural Journal,
References, Chapter 12 V. 90, No. 2, Mar.-Apr. 1993, pp. 210-217.
12.1. ACI Committee 408, “Bond Stress—The State of the Art,” ACI 12.15. Thompson, M. K.; Ziehl, M. J.; Jirsa, J. O.; and Breen, J. E.,
JOURNAL, Proceedings V. 63, No. 11, Nov. 1966, pp. 1161-1188. “CCT Nodes Anchored by Headed Bars—Part 1: Behavior of
Nodes,” ACI Structural Journal, V. 102, No. 6, Nov.-Dec. 2005,
12.2. ACI Committee 408, “Suggested Development, Splice, and pp. 808-815.
Standard Hook Provisions for Deformed Bars in Tension (ACI
408.1R-90),” American Concrete Institute, Farmington Hills, MI, 12.16. Thompson, M. K.; Jirsa, J. O.; and Breen, J. E., “CCT
1990, 3 pp. Nodes Anchored by Headed Bars—Part 2: Capacity of Nodes,”
ACI Structural Journal, V. 103, No. 1, Jan.-Feb. 2006, pp. 65-73.
12.3. Jirsa, J. O.; Lutz, L. A.; and Gergely, P., “Rationale for
Suggested Development, Splice, and Standard Hook Provisions for 12.17. Thompson, M. K.; Ledesma, A.; Jirsa, J. O.; and Breen, J. E.,
Deformed Bars in Tension,” Concrete International: Design & “Lap Splices Anchored by Headed Bars,” ACI Structural Journal,
Construction, V. 1, No. 7, July 1979, pp. 47-61. V. 103, No. 2, Mar.-Apr. 2006, pp. 271-279.
12.4. Azizinamini, A.; Chisala, M.; and Ghosh, S. K., “Tension 12.18. Bartoletti, S. J., and Jirsa, J. O., “Effects of Epoxy-Coating
12.29. Joint PCI/WRI Ad Hoc Committee on Welded Wire Fabric 13.11. Morrison, D. G., and Sozen, M. A., “Response to Reinforced
for Shear Reinforcement, “Welded Wire Fabric for Shear Reinforce- Concrete Plate-Column Connections to Dynamic and Static
ment,” Journal of the Prestressed Concrete Institute, V. 25, No. 4, Horizontal Loads,” Structural Research Series No. 490, Civil
July-Aug. 1980, pp. 32-36. Engineering Studies, University of Illinois, Apr. 1981, 249 pp.
12.30. Pfister, J. F., and Mattock, A. H., “High Strength Bars as 13.12. Vanderbilt, M. D., and Corley, W. G., “Frame Analysis of
Concrete Reinforcement, Part 5: Lapped Splices in Concentrically Concrete Buildings,” Concrete International: Design and
Loaded Columns,” Journal, PCA Research and Development Construction, V. 5, No. 12, Dec. 1983, pp. 33-43.
Laboratories, V. 5, No. 2, May 1963, pp. 27-40.
13.13. Grossman, J. S., “Code Procedures, History, and Shortcomings:
12.31. Lloyd, J. P., and Kesler, C. E., “Behavior of One-Way Slabs Column-Slab Connections,” Concrete International, V. 11, No. 9,
Reinforced with Deformed Wire and Deformed Wire Fabric,” Sept. 1989, pp. 73-77.
T&AM Report No. 323, University of Illinois, 1969, 129 pp.
13.14. Moehle, J. P., “Strength of Slab-Column Edge Connections,”
12.32. Lloyd, J. P., “Splice Requirements for One-Way Slabs ACI Structural Journal, V. 85, No. 1, Jan.-Feb. 1988, pp. 89-98.
Reinforced with Smooth Welded Wire Fabric,” Publication No. R(S)4,
Civil Engineering, Oklahoma State University, Stillwater, OK, 13.15. Joint ACI-ASCE Committee 352, “Recommendations for
June 1971, 37 pp. Design of Slab-Column Connections in Monolithic Reinforced
Concrete Structures (ACI 352.1R-89) (Reapproved 2004),” 15.2. Kramrisch, F., and Rogers, P., “Simplified Design of
American Concrete Institute, Farmington Hills, MI, 1989, 26 pp. Combined Footings,” Proceedings, ASCE, V. 87, No. SM5, Oct.
1961, p. 19.
13.16. Jirsa, J. O.; Sozen, M. A.; and Siess, C. P., “Pattern
Loadings on Reinforced Concrete Floor Slabs,” Proceedings, 15.3 Adebar, P.; Kuchma, D.; and Collins, M. P., “Strut-and-Tie
ASCE, V. 95, No. ST6, June 1969, pp. 1117-1137. Models for the Design of Pile Caps: An Experimental Study,” ACI
Structural Journal, V. 87, No. 1, Jan.-Feb. 1990, pp. 81-92.
13.17. Nichols, J. R., “Statical Limitations upon the Steel Requirement
in Reinforced Concrete Flat Slab Floors,” Transactions, ASCE, 15.4. CRSI Handbook, 8th Edition, Concrete Reinforcing Steel
V. 77, 1914, pp. 1670-1736. Institute, Schaumburg, IL, 2008.
13.18. Corley, W. G.; Sozen, M. A.; and Siess, C. P., “Equivalent- References, Chapter 16
Frame Analysis for Reinforced Concrete Slabs,” Structural
Research Series No. 218, Civil Engineering Studies, University of 16.1. Industrialization in Concrete Building Construction, SP-48,
Illinois, June 1961, 166 pp. American Concrete Institute, Farmington Hills, MI, 1975, 240 pp.
13.19. Jirsa, J. O.; Sozen, M. A.; and Siess, C. P., “Effects of 16.2. Waddell, J. J., “Precast Concrete: Handling and Erection,”
Pattern Loadings on Reinforced Concrete Floor Slabs,” Structural Monograph No. 8, American Concrete Institute, Farmington Hills,
Research Series No. 269, Civil Engineering Studies, University of MI, 1974, 146 pp.
Illinois, July 1963.
16.3. “Design and Typical Details of Connections for Precast and
13.20. Corley, W. G., and Jirsa, J. O., “Equivalent Frame Analysis Prestressed Concrete,” MNL-123-88, 2nd Edition, Precast/
for Slab Design,” ACI JOURNAL, Proceedings V. 67, No. 11, Nov. Prestressed Concrete Institute, Chicago, IL, 1988, 270 pp.
1970, pp. 875-884.
16.4. PCI Design Handbook: Precast and Prestressed Concrete,
13.21. Gamble, W. L., “Moments in Beam Supported Slabs,” ACI 6th Edition, MNL-120-4, Precast/Prestressed Concrete Institute,
JOURNAL, Proceedings V. 69, No. 3, Mar. 1972, pp. 149-157. Chicago, IL, 2004, 736 pp.
16.14. Johnson, T., and Ghadiali, Z., “Load Distribution Test on 17.3. Saemann, J. C., and Washa, G. W., “Horizontal Shear
Precast Hollow Core Slabs with Openings,” PCI Journal, V. 17, Connections between Precast Beams and Cast-in-Place Slabs,”
No. 5, Sept.-Oct. 1972, pp. 9-19. ACI JOURNAL, Proceedings V. 61, No. 11, Nov. 1964, pp. 1383-1409.
Also see discussion, ACI JOURNAL, June 1965.
16.15. Pfeifer, D. W., and Nelson, T. A., “Tests to Determine the
Lateral Distribution of Vertical Loads in a Long-Span Hollow- 17.4. Hanson, N. W., “Precast-Prestressed Concrete Bridges: Hori-
Core Floor Assembly,” PCI Journal, V. 28, No. 6, Nov.-Dec. 1983, zontal Shear Connections,” Journal, PCA Research and Develop-
pp. 42-57. ment Laboratories, V. 2, No. 2, May 1960, pp. 38-58.
16.16. Stanton, J., “Proposed Design Rules for Load Distribution 17.5. Grossfield, B., and Birnstiel, C., “Tests of T-Beams with
in Precast Concrete Decks,” ACI Structural Journal, V. 84, No. 5, Precast Webs and Cast-in-Place Flanges,” ACI JOURNAL, Proceedings
Sept.-Oct. 1987, pp. 371-382. V. 59, No. 6, June 1962, pp. 843-851.
16.17. Manual for the Design of Hollow Core Slabs, MNL-126-98, 17.6. Mast, R. F., “Auxiliary Reinforcement in Concrete
2nd Edition, Precast/Prestressed Concrete Institute, Chicago, IL, Connections,” Proceedings, ASCE, V. 94, No. ST6, June 1968,
1998, 144 pp. pp. 1485-1504.
18.11. Joint ACI-ASCE Committee 423, “Recommendations for Concrete Structures (ACI 352.1R-89) (Reapproved 2004),” Amer-
Concrete Members Prestressed with Unbonded Tendons (ACI 423.3R- ican Concrete Institute, Farmington Hills, MI, 1989, 26 pp.
05),” American Concrete Institute, Farmington Hills, MI, 2005, 25 pp.
18.27. American Association of State Highway and Transportation
18.12. Mattock, A. H.; Yamazaki, J.; and Kattula, B. T., “Comparative Officials, “AASHTO LRFD Bridge Design Specifications,” 3rd
Study of Prestressed Concrete Beams, with and without Bond,” Edition, 2004.
ACI JOURNAL, Proceedings V. 68, No. 2, Feb. 1971, pp. 116-125.
18.28. Breen, J. E.; Burdet, O.; Roberts, C.; Sanders, D.; Woll-
18.13. Odello, R. J., and Mehta, B. M., “Behavior of a Continuous mann, G.; and Falconer, B., “Anchorage Zone Requirements for
Prestressed Concrete Slab with Drop Panels,” Report, Division of Post-Tensioned Concrete Girders,” NCHRP Report 356, Transpor-
Structural Engineering and Structural Mechanics, University of tation Research Board, National Academy Press, Washington,
California, Berkeley, CA, 1967. D.C., 1994.
18.14. Smith, S. W., and Burns, N. H., “Post-Tensioned Flat Plate 18.29. Joint ACI-ASCE Committee 423, “Specification for
to Column Connection Behavior,” Journal of the Prestressed Unbonded Single-Strand Tendon Materials and Commentary (ACI
Concrete Institute, V. 19, No. 3, May-June 1974, pp. 74-91. 423.7-07),” American Concrete Institute, Farmington Hills, MI,
2007.
18.15. Burns, N. H., and Hemakom, R., “Test of Scale Model Post-
Tensioned Flat Plate,” Proceedings, ASCE, V. 103, No. ST6, June 18.30. “Guide Specifications for Design and Construction of
1977, pp. 1237-1255. Segmental Concrete Bridges,” AASHTO, Washington, DC, 1989,
50 pp.
18.16. Hawkins, N. M., “Lateral Load Resistance of Unbonded
Post-Tensioned Flat Plate Construction,” Journal of the Prestressed 18.31. Gerwick, B. C. Jr., “Protection of Tendon Ducts,” Construc-
Concrete Institute, V. 26, No. 1, Jan.-Feb. 1981, pp. 94-116. tion of Prestressed Concrete Structures, John Wiley and Sons, Inc.,
New York, 1971, 411 pp.
18.17. “Guide Specifications for Post-Tensioning Materials,” Post-
Tensioning Manual, 5th Edition, Post-Tensioning Institute, 18.32. “Specification for Grouting of Post-Tensioned Structures,”
Phoenix, AZ, 1990, pp. 208-216. 2nd Edition, Post-Tensioning Institute, Phoenix, AZ, 2003, 60 pp.
18.18. Foutch, D. A.; Gamble, W. L.; and Sunidja, H., “Tests of 18.33. Manual for Quality Control for Plants and Production of
Post-Tensioned Concrete Slab-Edge Column Connections,” ACI Structural Precast Concrete Products, 4th Edition, MNL-116-99,
Structural Journal, V. 87, No. 2, Mar.-Apr. 1990, pp. 167-179. Precast/Prestressed Concrete Institute, Chicago, IL, 1999.
18.19. Bondy, K. B., “Moment Redistribution: Principles and 18.34. ACI Committee 301, “Specifications for Structural
Practice Using ACI 318-02,” PTI Journal, V. 1, No. 1, Jan. 2003, Concrete (ACI 301-05),” American Concrete Institute, Farmington
pp. 3-21. Hills, MI, 2005, 49 pp.
18.20. Lin, T. Y., and Thornton, K., “Secondary Moment and 18.35. Salmons, J. R., and McCrate, T. E., “Bond Characteristics
Moment Redistribution in Continuous Prestressed Beams,” PCI of Untensioned Prestressing Strand,” Journal of the Prestressed
Journal, V. 17, No. 1, Jan.-Feb. 1972, pp. 8-20 and comments by Concrete Institute, V. 22, No. 1, Jan.-Feb. 1977, pp. 52-65.
A. H. Mattock and author’s closure, PCI Journal, V. 17, No. 4,
July-Aug. 1972, pp. 86-88. 18.36. ACI Committee 215, “Considerations for Design of
Concrete Structures Subjected to Fatigue Loading (ACI 215R-74)
18.21. Collins, M. P., and Mitchell, D., Prestressed Concrete (Revised 1992) (Reapproved 1997),” American Concrete Institute,
Structures, Response Publications, Canada, 1997, pp. 517-518. Farmington Hills, MI, 1992, 24 pp.
18.22. Mast, R. F., “Unified Design Provision for Reinforced and 18.37. Barth, F., “Unbonded Post-Tensioning in Building
Prestressed Concrete Flexural and Compression Members,” ACI Construction,” Concrete Construction Engineering Handbook,
Structural Journal, V. 89, No. 2, Mar.-Apr. 1992, pp. 185-199. CRC Press, 1997, pp. 12.32-12.47.
19.4. ACI Committee 334, “Reinforced Concrete Cooling Tower 19.20. ACI Committee 224, “Control of Cracking in Concrete
Shells—Practice and Commentary (ACI 334.2R-91),” American Structures (ACI 224R-01),” American Concrete Institute, Farm-
Concrete Institute, Farmington Hills, MI, 1991, 9 pp. ington Hills, MI, 2001, 46 pp.
19.5. ACI Committee 373, “Design and Construction of Circular 19.21. Gupta, A. K., “Combined Membrane and Flexural Reinforce-
Prestressed Concrete Structures with Circumferential Tendons ment in Plates and Shells,” Journal of Structural Engineering,
(ACI 373R-97),” American Concrete Institute, Farmington Hills, ASCE, V. 112, No. 3, Mar, 1986, pp. 550-557.
MI, 1997, 26 pp.
19.22. Tedesko, A., “Construction Aspects of Thin Shell Structures,”
19.6. Billington, D. P., Thin Shell Concrete Structures, 2nd ACI JOURNAL, Proceedings V. 49, No. 6, Feb. 1953, pp. 505-520.
Edition, McGraw-Hill Book Co., New York, 1982, 373 pp.
19.23. Huber, R. W., “Air Supported Forming—Will it Work?”
19.7. “Phase I Report on Folded Plate Construction,” ASCE Task Concrete International, V. 8, No. 1, Jan. 1986, pp. 13-17.
Committee, Journal of Structural Division, ASCE, V. 89, No. ST6,
1963, pp. 365-406. References, Chapter 20
19.8. Concrete Thin Shells, SP-28, American Concrete Institute, 20.1. ACI Committee 214, “Guide for Obtaining Cores and Inter-
Farmington Hills, MI, 1971, 424 pp. preting Compressive Strength Results (ACI 214.4R-03),” Amer-
ican Concrete Institute, Farmington Hills, MI, 2003, 16 pp.
19.9. Esquillan N., “The Shell Vault of the Exposition Palace,
Paris,” Journal of Structural Division, ASCE, V. 86, No. ST1, Jan. References, Chapter 21
1960, pp. 41-70.
21.1. “Minimum Design Loads for Buildings and Other Struc-
tures,” ASCE/SEI 7-05, American Society of Civil Engineers,
19.10. Hyperbolic Paraboloid Shells, SP-110, American Concrete
Reston, VA, 2005.
Institute, Farmington Hills, MI, 1988, 184 pp.
21.2. “International Building Code,” International Code Council,
19.11. Billington, D. P., “Thin Shell Structures,” Structural Engi- Falls Church, VA, 2006.
neering Handbook, Gaylord and Gaylord, eds., McGraw-Hill, New
York, 1990, pp. 24.1-24.57.
21.3. Uniform Building Code, V. 2, “Structural Engineering Design
Provisions,” International Conference of Building Officials,
19.12. Scordelis, A. C., “Non-Linear Material, Geometric, and Whittier, CA, 1997.
Time Dependent Analysis of Reinforced and Prestressed Concrete
Shells,” Bulletin, International Association for Shells and Spatial 21.4. “2003 NEHRP Recommended Provisions for Seismic Regu-
Structures, Madrid, Spain, No. 102, Apr. 1990, pp. 57-90. lations for New Buildings and Other Structures,” Building Seismic
Safety Council, Washington, DC, (FEMA 450-CD), 2003.
19.13. Schnobrich, W. C., “Reflections on the Behavior of Rein-
forced Concrete Shells,” Engineering Structures, Butterworth, 21.5. Blume, J. A.; Newmark, N. M.; and Corning, L. H., Design
Heinemann, Ltd., Oxford, V. 13, No. 2, Apr. 1991, pp. 199-210. of Multistory Reinforced Concrete Buildings for Earthquake
Motions, Portland Cement Association, Skokie, IL, 1961, 318 pp.
19.14. Sabnis, G. M.; Harris, H. G.; and Mirza, M. S., Structural
Modeling and Experimental Techniques, Prentice-Hall, Inc., 21.6. Clough, R. W., “Dynamic Effects of Earthquakes,” Proceedings,
Englewood Cliffs, NJ, 1983. ASCE, V. 86, No. ST4, Apr. 1960, pp. 49-65.
19.15. Concrete Shell Buckling, SP-67, American Concrete Institute, 21.7. Gulkan, P., and Sozen, M. A., “Inelastic Response of
Farmington Hills, MI, 1981, 234 pp. Reinforced Concrete Structures to Earthquake Motions,” ACI
JOURNAL, Proceedings V. 71, No. 12, Dec. 1974, pp. 604-610.
19.16. Gupta, A. K., “Membrane Reinforcement in Concrete
Shells: A Review,” Nuclear Engineering and Design, Nofi-Holland 21.8. Joint ACI-ASCE Committee 352, “Recommendations for
Publishing, Amsterdam, V. 82, Oct. 1984, pp. 63-75. Design of Beam-Column Connections in Monolithic Reinforced
Concrete Structures (ACI 352R-02),” American Concrete Institute,
19.17. Vecchio, F. J., and Collins, M. P., “Modified Compression- Farmington Hills, MI, 2002, 37 pp.
Field Theory for Reinforced Concrete Beams Subjected to
Shear,” ACI JOURNAL, Proceedings V. 83, No. 2, Mar.-Apr. 1986, 21.9. Budek, A.; Priestley, M.; and Lee, C., “Seismic Design of
pp. 219-223. Columns with High-Strength Wire and Strand as Spiral Reinforce-
ment,” ACI Structural Journal, V. 99, No. 5, Sept.-Oct. 2002,
19.18. Fialkow, M. N., “Compatible Stress and Cracking in Rein- pp. 660-670.
forced Concrete Membranes with Multidirectional Reinforcement,”
ACI Structural Journal, V. 88, No. 4, July-Aug. 1991, pp. 445-457. 21.10. Muguruma, H., and Watanabe, F., “Ductility Improvement
of High-Strength Concrete Columns with Lateral Confinement,”
19.19. Medwadowski, S., “Multidirectional Membrane Rein- Proceedings, Second International Symposium on High-Strength
forcement,” ACI Structural Journal, V. 86, No. 5, Sept.-Oct. Concrete, SP-121, American Concrete Institute, Farmington Hills,
1989, pp. 563-569. MI, 1990, pp. 47-60.
21.11. Sugano, S.; Nagashima, T.; Kimura, H.; Tamura, A.; and 21.24. Sivakumar, B.; Gergely, P.; and White, R. N., “Suggestions
Ichikawa, A., “Experimental Studies on Seismic Behavior of for the Design of R/C Lapped Splices for Seismic Loading,”
Reinforced Concrete Members of High Strength Concrete,” Concrete International, V. 5, No. 2, Feb. 1983, pp. 46-50.
Proceedings, Second International Symposium on High-Strength
Concrete, SP-121, American Concrete Institute, Farmington Hills, 21.25. Watson, S.; Zahn, F. A.; and Park, R., “Confining Reinforce-
MI, 1990, pp. 61-87. ment for Concrete Columns,” Journal of Structural Engineering,
V. 120, No. 6, June 1994, pp. 1798-1824.
21.12. Joint ACI-ASCE Committee 352, “Recommendations for
Design of Slab-Column Connections in Monolithic Reinforced 21.26. Sakai, K., and Sheikh, S. A., “What Do We Know about
Concrete Structures (ACI 352.1R-89) (Reapproved 2004),” Amer- Confinement in Reinforced Concrete Columns? (A Critical
ican Concrete Institute, Farmington Hills, MI, 1989, 26 pp. Review of Previous Work and Code Provisions),” ACI Structural
Journal, V. 86, No. 2, Mar.-Apr. 1989, pp. 192-207.
21.13. Pan, A., and Moehle, J. P., “Lateral Displacement Ductility
of Reinforced Concrete Flat Plates,” ACI Structural Journal, V. 86, 21.27. Park, R., “Ductile Design Approach for Reinforced
No. 3, May-June 1989, pp. 250-258. Concrete Frames,” Earthquake Spectra, V. 2, No. 3, May 1986,
pp. 565-619.
21.14. Hirosawa, M., “Strength and Ductility of Reinforced
Concrete Members,” Report No. 76, Building Research Institute, 21.28. Meinheit, D. F., and Jirsa, J. O., “Shear Strength of Reinforced
Ministry of Construction, Tokyo, Mar. 1977 (in Japanese). Also, Concrete Beam-Column Joints,” Report No. 77-1, Department of
data in Civil Engineering Studies, Structural Research Series Civil Engineering, Structures Research Laboratory, University of
No. 452, University of Illinois, 1978. Texas at Austin, TX, Jan. 1977.
21.15. Joint ACI-ASCE Committee 423, “Recommendations for 21.29. Briss, G. R.; Paulay, T; and Park, R., “Elastic Behavior of
Concrete Members Prestressed with Unbonded Tendons (ACI Earthquake Resistant R. C. Interior Beam-Column Joints,” Report
423.3R-05),” American Concrete Institute, Farmington Hills, MI, 78-13, University of Canterbury, Department of Civil Engineering,
2005, 21 pp. Christchurch, New Zealand, Feb. 1978.
21.16. Ishizuka, T., and Hawkins, N. M., “Effect of Bond Deterio- 21.30. Ehsani, M. R., “Behavior of Exterior Reinforced Concrete
ration on the Seismic Response of Reinforced and Partially Beam to Column Connections Subjected to Earthquake Type
Prestressed Concrete Ductile Moment Resistant Frames,” Report Loading,” Report No. UMEE 82R5, Department of Civil Engi-
SM 87-2, Department of Civil Engineering, University of Wash- neering, University of Michigan, Ann Arbor, MI, July 1982, 275 pp.
ington, Seattle, WA, 1987.
21.31. Durrani, A. J., and Wight, J. K., “Experimental and Analytical
Study of Internal Beam to Column Connections Subjected to
21.17. Park, R., and Thompson, K. J., “Cyclic Load Tests on
Reversed Cyclic Loading,” Report No. UMEE 82R3, Department
Prestressed and Partially Prestressed Beam-Column Joints,” Journal
of Civil Engineering, University of Michigan, Ann Arbor, MI, July
of the Prestressed Concrete Institute, V. 22, No. 3, 1977, pp. 84-110.
1982, 275 pp.
21.18. Thompson, K. J., and Park, R., “Seismic Response of
21.32. Leon, R. T., “Interior Joints with Variable Anchorage
Partially Prestressed Concrete,” Journal of the Structural Division,
Lengths,” Journal of Structural Engineering, ASCE, V. 115, No. 9,
ASCE, V. 106, No. ST8, 1980, pp. 1755-1775.
Sept. 1989, pp. 2261-2275.
21.19. Joint ACI-ASCE Committee 423, “Specification for Unbonded 21.33. Zhu, S., and Jirsa, J. O., “Study of Bond Deterioration in
Single-Strand Tendon Materials and Commentary (ACI 423.7-07),” Reinforced Concrete Beam-Column Joints,” PMFSEL Report No.
American Concrete Institute, Farmington Hills, MI, 2007. 83-1, Department of Civil Engineering, University of Texas at
Austin, TX, July 1983.
21.20. Popov, E. P.; Bertero, V. V.; and Krawinkler, H., “Cyclic
Behavior of Three R/C Flexural Members with High Shear,” 21.34. Joint ACI-ASCE Committee 326, “Shear and Diagonal
EERC Report No. 72-5, Earthquake Engineering Research Center, Tension,” ACI JOURNAL, Proceedings V. 59, No. 1, Jan. 1962,
University of California, Berkeley, CA, Oct. 1972. pp. 1-30; No. 2, Feb. 1962, pp. 277-334; and No. 3, Mar. 1962,
pp. 352-396.
21.21. Wight, J. K., and Sozen, M. A., “Shear Strength Decay of
RC Columns under Shear Reversals,” Proceedings, ASCE, V. 101, 21.35. Ehsani, M. R., “Behavior of Exterior Reinforced Concrete
No. ST5, May 1975, pp. 1053-1065. Beam to Column Connections Subjected to Earthquake Type
Loading,” ACI JOURNAL, Proceedings V. 82, No. 4, July-Aug.
21.22. “Recommended Lateral Force Requirements and 1985, pp. 492-499.
Commentary,” 6th Edition, Seismology Committee of the Structural
Engineers Association of California, Sacramento, CA, 504 pp. 21.36. Meinheit, D. F., and Jirsa, J. O., “Shear Strength of R/C
Beam-Column Connections,” Journal of the Structural Division,
21.23. French, C. W., and Moehle, J. P., “Effect of Floor Slab on ASCE, V. 107, No. ST11, Nov. 1981, pp. 2227-2244.
Behavior of Slab-Beam-Column Connections,” Design of Beam-
Column Joints for Seismic Resistance, SP-123, American Concrete 21.37. Yoshioka, K., and Sekine, M., “Experimental Study of
Institute, Farmington Hills, MI, 1991, pp. 225-258. Prefabricated Beam-Column Subassemblages,” Design of Beam-
Column Joints for Seismic Resistance, SP-123, American Concrete 21.51. Thomsen, J. H., and Wallace, J. W., “Displacement Design
Institute, Farmington Hills, MI, 1991, pp. 465-492. of Slender Reinforced Concrete Structural Walls—Experimental
Verification,” Journal of Structural Engineering, ASCE, V. 130,
21.38. Kurose, Y.; Nagami, K.; and Saito, Y., “Beam-Column No. 4, 2004, pp. 618-630.
Joints in Precast Concrete Construction in Japan,” Design of Beam-
Column Joints for Seismic Resistance, SP-123, American Concrete 21.52. Paulay, T., and Binney, J. R., “Diagonally Reinforced
Institute, 1991, pp. 493-514. Coupling Beams of Shear Walls,” Shear in Reinforced Concrete,
SP-42, American Concrete Institute, Farmington Hills, MI, 1974,
21.39. Restrepo, J. I.; Park, R.; and Buchanan, A. H., “Tests on pp. 579-598.
Connections of Earthquake Resisting Precast Reinforced Concrete
Perimeter Frames of Buildings,” PCI Journal, V. 40, No. 4, July- 21.53. Barney, G. B.; Shiu, K. N.; Rabbat, B. G.; Fiorato, A. E.;
Aug. 1995, pp. 44-61. Russell, H. G.; and Corley, W. G., Behavior of Coupling Beams
under Load Reversals (RD068.01B), Portland Cement Association,
21.40. Restrepo, J.; Park, R.; and Buchanan, A., “Design of Skokie, IL, 1980.
Connections of Earthquake Resisting Precast Reinforced Concrete
Perimeter Frames,” Precast/Prestressed Concrete Institute Journal, 21.54. Priestley, M. J. N.; Sritharan, S.; Conley, J.; and Pampanin,
V. 40, No. 5, 1995, pp. 68-80. S., “Preliminary Results and Conclusions from the PRESSS Five-
Story Precast Concrete Test Building,” PCI Journal, V. 44, No. 6,
21.41. Palmieri, L.; Saqan, E.; French, C.; and Kreger, M., Nov.-Dec. 1999, pp. 42-67.
“Ductile Connections for Precast Concrete Frame Systems,” Mete
A. Sozen Symposium, SP-162, American Concrete Institute, Farm- 21.55. Perez, F. J.; Pessiki, S.; Sause, R.; and Lu, L.-W., “Lateral
ington Hills, MI, 1996, pp. 315-335. Load Tests of Unbonded Post-Tensioned Precast Concrete Walls,”
Large Scale Structural Testing, SP-211, American Concrete Insti-
21.42. Stone, W.; Cheok, G.; and Stanton, J., “Performance of tute, Farmington Hills, MI, 2003, pp. 161-182.
Hybrid Moment-Resisting Precast Beam-Column Concrete
Connections Subjected to Cyclic Loading,” ACI Structural 21.56. Restrepo, J. I., “New Generation of Earthquake Resisting
Journal, V. 92, No. 2, Mar.-Apr. 1995, pp. 229-249. Systems,” Proceedings, First fib Congress, Session 6, Osaka,
Japan, Oct. 2002, pp. 41-60.
21.43. Nakaki, S. D.; Stanton, J. F.; and Sritharan, S., “An Over-
view of the PRESSS Five-Story Precast Test Building,” Precast/ 21.57. Wyllie, L. A., Jr., “Structural Walls and Diaphragms — How
Prestressed Concrete Institute Journal, V. 44, No. 2, pp. 26-39. They Function,” Building Structural Design Handbook, R. N. White,
and C. G. Salmon, eds., John Wiley & Sons, 1987, pp. 188-215.
21.44. ACI Innovation Task Group 1, “Special Hybrid Moment
21.58. Wood, S. L.; Stanton, J. F.; and Hawkins, N. M., “Develop-
Frames Composed of Discretely Jointed Precast and Post-
ment of New Seismic Design Provisions for Diaphragms Based on
Tensioned Concrete Members (ITG-1.2-03) and Commentary
the Observed Behavior of Precast Concrete Parking Garages during
(ITG-1.2R-03),” American Concrete Institute, Farmington Hills,
the 1994 Northridge Earthquake,” PCI Journal, V. 45, No. 1, Jan.-
MI, 2003.
Feb. 2000, pp. 50-65.
21.45. ACI Committee 408, “Bond Under Cyclic Loads (ACI
21.59. Nilsson, I. H. E., and Losberg, A., “Reinforced Concrete
408.2R-92) (Reapproved 2005),” American Concrete Institute,
Corners and Joints Subjected to Bending Moment,” Journal of the
Farmington Hills, MI, 1992, 5 pp.
Structural Division, ASCE, V. 102, No. ST6, June 1976, pp. 1229-1254.
21.46. Barda, F.; Hanson, J. M.; and Corley, W. G., “Shear 21.60. Megally, S., and Ghali, A., “Punching Shear Design of
Strength of Low-Rise Walls with Boundary Elements,” Reinforced Earthquake-Resistant Slab-Column Connections,” ACI Structural
Concrete Structures in Seismic Zones, SP-53, American Concrete Journal, V. 97, No. 5, Sept.-Oct. 2002, pp. 720-730.
Institute, Farmington Hills, MI, 1977, pp. 149-202.
21.61. Moehle, J. P., “Seismic Design Considerations for Flat Plate
21.47. Taylor, C. P.; Cote, P. A.; and Wallace, J. W., “Design of Construction,” Mete A. Sozen Symposium: A Tribute from his
Slender RC Walls with Openings,” ACI Structural Journal, V. 95, Students, SP-162, J. K. Wight and M. E. Kreger, eds., American
No. 4, July-Aug. 1998, pp. 420-433. Concrete Institute, Farmington Hills, MI, pp. 1-35.
A.4. FIP Recommendations, Practical Design of Structural C.2. “Minimum Design Loads for Buildings and Other Structures
Concrete, FIP-Commission 3, “Practical Design,” Pub.: SETO, (ASCE 7-93),” ASCE, New York, 1993, 134 pp.
London, Sept. 1999.
C.3. “BOCA National Building Code,” 12th Edition, Building
A.5. Menn, C., Prestressed Concrete Bridges, Birkhäuser, Basle, Officials and Code Administration International, Inc., Country
535 pp. Club Hills, IL, 1993, 357 pp.
A.6. Muttoni, A.; Schwartz, J.; and Thürlimann, B., Design of C.4. “Standard Building Code, 1994 Edition,” Southern Building
Concrete Structures with Stress Fields, Birkhauser, Boston, MA, Code Congress International, Inc., Birmingham, AL, 1994, 656 pp.
1997, 143 pp.
C.5. “Uniform Building Code, V. 2, Structural Engineering Design
A.7. Joint ACI-ASCE Committee 445, “Recent Approaches to Provisions,” International Conference of Building Officials,
Shear Design of Structural Concrete (ACI 445R-99),” American Whittier, CA, 1997, 492 pp.
Concrete Institute, Farmington Hills, MI, 1999, 55 pp.
C.6. Mast, R. F., “Unified Design Provisions for Reinforced and
A.8. Bergmeister, K.; Breen, J. E.; and Jirsa, J. O., “Dimensioning Prestressed Concrete Flexural and Compression Members,” ACI
of the Nodes and Development of Reinforcement,” IABSE Collo- Structural Journal, V. 89, No. 2, Mar.-Apr. 1992, pp. 185-199.
quium Stuttgart 1991, International Association for Bridge and
Structural Engineering, Zurich, 1991, pp. 551-556. References, Appendix D
D.1. ANSI/ASME B1.1, “Unified Inch Screw Threads (UN and
References, Appendix B UNR Thread Form),” ASME, Fairfield, NJ, 1989.
B.1. Bondy, K. B., “Moment Redistribution—Principles and Practice
Using ACI 318-02,” PTI Journal, V. 1, No. 1, Jan. 2003, pp. 3-21. D.2. ANSI/ASME B18.2.1, “Square and Hex Bolts and Screws,
Inch Series,” ASME, Fairfield, NJ, 1996.
B.2. Cohn, M. A., “Rotational Compatibility in the Limit Design
D.3. ANSI/ASME B18.2.6, “Fasteners for Use in Structural Appli-
of Reinforced Concrete Continuous Beams,” Flexural Mechanics
cations,” ASME, Fairfield, NJ, 1996.
of Reinforced Concrete, SP-12, American Concrete Institute/
American Society of Civil Engineers, Farmington Hills, MI, 1965,
D.4. Cook, R. A., and Klingner, R. E., “Behavior of Ductile
pp. 35-46.
Multiple-Anchor Steel-to-Concrete Connections with Surface-
Mounted Baseplates,” Anchors in Concrete: Design and Behavior,
B.3. Mattock, A. H., “Redistribution of Design Bending Moments
SP-130, American Concrete Institute, Farmington Hills, MI, 1992,
in Reinforced Concrete Continuous Beams,” Proceedings, Institu-
pp. 61-122.
tion of Civil Engineers, London, V. 13, 1959, pp. 35-46.
D.5. Cook, R. A., and Klingner, R. E., “Ductile Multiple-Anchor
B.4. Design of Post-Tensioned Slabs Using Unbonded Tendons, Steel-to-Concrete Connections,” Journal of Structural Engi-
3rd Edition, Post-Tensioning Institute, Phoenix, AZ, 2004, 87 pp. neering, ASCE, V. 118, No. 6, June 1992, pp. 1645-1665.
B.5. Gerber, L. L., and Burns, N. H., “Ultimate Strength Tests of D.6. Lotze, D.; Klingner, R. E.; and Graves III, H. L., “Static
Post-Tensioned Flat Plates,” Journal of the Prestressed Concrete Behavior of Anchors under Combinations of Tension and Shear
Institute, V. 16, No. 6, Nov.-Dec. 1971, pp. 40-58. Loading,” ACI Structural Journal, V. 98, No. 4, July-Aug. 2001,
pp. 525-536.
B.6. Smith, S. W., and Burns, N. H., “Post-Tensioned Flat Plate to
Column Connection Behavior,” Journal of the Prestressed D.7. Primavera, E. J.; Pinelli, J.-P.; and Kalajian, E. H., “Tensile
Concrete Institute, V. 19, No. 3, May-June 1974, pp. 74-91. Behavior of Cast-in-Place and Undercut Anchors in High-Strength
Concrete,” ACI Structural Journal, V. 94, No. 5, Sept.-Oct. 1997,
B.7. Burns, N. H., and Hemakom, R., “Test of Scale Model Post- pp. 583-594.
Tensioned Flat Plate,” Proceedings, ASCE, V. 103, No. ST6, June
1977, pp. 1237-1255. D.8. Design of Fastenings in Concrete, Comite Euro-International
du Beton (CEB), Thomas Telford Services Ltd., London, Jan.
B.8. Burns, N. H., and Hemakom, R., “Test of Flat Plate with 1997.
Bonded Tendons,” Proceedings, ASCE, V. 111, No. 9, Sept. 1985,
pp. 1899-1915. D.9. Fuchs, W.; Eligehausen, R.; and Breen, J., “Concrete Capacity
Design (CCD) Approach for Fastening to Concrete,” ACI Structural
B.9. Kosut, G. M.; Burns, N. H.; and Winter, C. V., “Test of Four- Journal, V. 92, No. 1, Jan.-Feb. 1995, pp. 73-93. Also discussion,
Panel Post-Tensioned Flat Plate,” Proceedings, ASCE, V. 111, No. 9, ACI Structural Journal, V. 92, No. 6, Nov.-Dec. 1995, pp. 787-802.
Sept. 1985, pp. 1916-1929.
D.10. Eligehausen, R., and Balogh, T., “Behavior of Fasteners
References, Appendix C Loaded in Tension in Cracked Reinforced Concrete,” ACI Struc-
tural Journal, V. 92, No. 3, May-June 1995, pp. 365-379.
C.1. “International Building Code,” International Code Council,
Falls Church, VA, 2000. D.11. “Fastenings to Concrete and Masonry Structures, State of the
Art Report,” Comite Euro-International du Beton (CEB), Bulletin D.18. PCI Design Handbook, 5th Edition, Precast/Prestressed
No. 216, Thomas Telford Services Ltd., London, 1994. Concrete Institute, Chicago, IL, 1999.
D.12. Klingner, R.; Mendonca, J.; and Malik, J., “Effect of D.19. “AISC Load and Resistance Factor Design Specifications for
Reinforcing Details on the Shear Resistance of Anchor Bolts Structural Steel Buildings,” Dec. 1999, 327 pp.
under Reversed Cyclic Loading,” ACI JOURNAL, Proceedings V. 79,
No. 1, Jan.-Feb. 1982, pp. 3-12. D.20. Zhang, Y.; Klingner, R. E.; and Graves III, H. L., “Seismic
Response of Multiple-Anchor Connections to Concrete,” ACI
D.13. ACI Committee 349, “Code Requirements for Nuclear Structural Journal, V. 98, No. 6, Nov.-Dec. 2001, pp. 811-822.
Safety Related Concrete Structures (ACI 349-01),” American
Concrete Institute, Farmington Hills, MI, 2001, 134 pp. D.21. Lutz, L., “Discussion to Concrete Capacity Design (CCD)
Approach for Fastening to Concrete,” ACI Structural Journal,
Nov.-Dec. 1995, pp. 791-792. Also authors’ closure, pp. 798-799.
D.14. Eligehausen, R.; Mallée, R.; and Silva, J., Anchorage in
Concrete Construction, Ernst & Sohn (J. T. Wiley), Berlin, May
D.22. Asmus, J., “Verhalten von Befestigungen bei der Versagen-
2006, 380 pp.
sart Spalten des Betons (Behavior of Fastenings with the Failure
Mode Splitting of Concrete),” dissertation, Universität Stuttgart,
D.15. Eligehausen, R.; Fuchs, W.; and Mayer, B., “Load Bearing Germany, 1999.
Behavior of Anchor Fastenings in Tension,” Betonwerk +
Fertigteiltechnik, 12/1987, pp. 826-832, and 1/1988, pp. 29-35. D.23. Kuhn, D., and Shaikh, F., “Slip-Pullout Strength of Hooked
Anchors,” Research Report, University of Wisconsin-Milwaukee,
D.16. Eligehausen, R., and Fuchs, W., “Load Bearing Behavior submitted to the National Codes and Standards Council, 1996.
of Anchor Fastenings under Shear, Combined Tension and Shear
or Flexural Loadings,” Betonwerk + Fertigteiltechnik, 2/1988, D.24. Furche, J., and Eligehausen, R., “Lateral Blow-out Failure of
pp. 48-56. Headed Studs Near a Free Edge,” Anchors in Concrete—Design
and Behavior, SP-130, American Concrete Institute, Farmington
D.17. Farrow, C. B., and Klingner, R. E., “Tensile Capacity of Hills, MI, 1991, pp. 235-252.
Anchors with Partial or Overlapping Failure Surfaces: Evaluation
of Existing Formulas on an LRFD Basis,” ACI Structural Journal, D.25. Shaikh, A. F., and Yi, W., “In-Place Strength of Welded
V. 92, No. 6, Nov.-Dec. 1995, pp. 698-710. Studs,” PCI Journal, V. 30, No. 2, Mar.-Apr. 1985.
INDEX
As ACI begins its second century of advancing concrete knowledge, its original chartered purpose
remains “to provide a comradeship in finding the best ways to do concrete work of all kinds and in
spreading knowledge.” In keeping with this purpose, ACI supports the following activities:
· Technical committees that produce consensus reports, guides, specifications, and codes.
· Periodicals: the ACI Structural Journal and the ACI Materials Journal, and Concrete International.
Benefits of membership include a subscription to Concrete International and to an ACI Journal. ACI
members receive discounts of up to 40% on all ACI products and services, including documents, seminars
and convention registration fees.
As a member of ACI, you join thousands of practitioners and professionals worldwide who share a
commitment to maintain the highest industry standards for concrete technology, construction, and
practices. In addition, ACI chapters provide opportunities for interaction of professionals and practitioners
at a local level.
www.concrete.org
®
American Concrete Institute
Advancing concrete knowledge