Professional Documents
Culture Documents
Unit 4 A
Unit 4 A
What is
Unreinforced
Masonry?
Unreinforced masonry can be
defined generally as masonry that
contains no reinforcing in it.
03
Basics Of Masonry
Masonry is made of earthen materials and
includes the sub-types listed below.
Basics Of
Masonry
Masonry is a term used to indicate
the part of construction that uses
brick, concrete block, structural
clay tile, and stone. These
materials are held together with Components of unreinforced brick and
mortar. Mortar for masonry unreinforced concrete block walls.
06
Concrete
Masonry Unit
Concrete Masonry Units –
Modular system :
Larger unit than brick
Dimensions related to modular brick
Wide variety of size and color
Lower labor cost than brick
Also called concrete block & cinder block
07
Concrete
Masonry Unit
08
Concrete
Masonry Unit
Types of CMU
Hollow concrete block
Solid concrete block
Concrete brick
Split-face block
09
Concrete
Masonry Unit
10
Concrete
Masonry Unit
11
Concrete
Masonry Unit
12
Concrete
Masonry Unit
Bond beam
Bond beam for lintel
14
Corner - Round and square
Construction method :
Masonary Building
Construction Systems
Unreinforced Masonry :
This form of construction is not considered
earthquake resistant and its use should be
disallowed.
Reinforced Masonry :
Two systems of reinforced masonry are in common
use:
Reinforced hollow units masonry :
This is achieved by placing bed joint reinforcement
of the type illustrated in Figure 10 at 600 mm
centers, and vertical bars as shown in Figure. The
15 holes containing the vertical bars are filled with
concrete as the construction of the wall progresses
Construction method :
Masonary Building
Reinforced cavity masonry
Confined Masonry
Walls
General Principles
• Walls are to be uniformly distributed along each
principal axis of the plan.
• The minimum thickness of structural walls should be
240 mm. The total cross-sectional area of structural
walls along each of the two axes should not be less
than 3% of the gross floor area.
17
GOOD CONSTRUCTION
PRACTICES
Walls
General Principles
• Distances between structural walls of reinforced masonry should not be more
than 6m; distances in confined masonry should not be more than 8m.
• Partitions should be reinforced with 6 mm ø bars placed at the bed joints with
vertical spacing of 600 mm in order to prevent their out-of-plane instability.
Partitions should be anchored to structural walls or tie columns with steel
anchors
19
GOOD CONSTRUCTION
PRACTICES
Lintels
Lintels should have a minimum of 250 mm bearing length at both ends to prevent local
collapse due to the crushing of supports during an earthquake.
The width of a lintel should not be less than150 mm. If the distance between the top of the
lintel and the underside of the beam above is less than 60 cm, the two should be united as
shown in Figure 15-a. In the case of openings larger in area than 2.5 m2, the lintel should
be anchored to the tie columns as shown in Figure 15-b.
20
GOOD CONSTRUCTION
PRACTICES
Double-Leaf Walls
• The traditional stone masonry construction with two outer layers of uncoursed
irregularly sized rubble stones with an inner infill consisting of smaller pieces
of stone bound together with lime mortar is not recommended in earthquake
zones.
• Generally speaking, single-leaf walls should be preferred to double-leaf walls.
Double-leaf cavity walls, where the cavity is filled with concrete, should be
preferred to normal cavity walls, since they ensure monolithic behaviour of the
wall under seismic conditions.
21
GOOD CONSTRUCTION
PRACTICES
Tie Beams
The function of tie beams is to transfer horizontal shear induced by the earthquakes
from the floor and roof to the structural walls.
They connect the structural walls with each other and improve the rigidity of the
horizontal diaphragms.
Tie beams should not be smaller in section than 150 x 150 mm.
The reinforcement should not be less than 4 no. 12mm ø with stirrups 6 mm ø at 200
mm centres.
Reinforcement should be spliced and anchored at cornets and wall intersections. Bars
should overlap by a minimum distance of 60 times the diameters of the bars.
Parapets should be reinforced vertically and horizontally.
The reinforcement should be tied in with the reinforcement in the tie beam.
22
GOOD CONSTRUCTION
PRACTICES
Cantilever Slabs and overhangs
These elements can cause harmful vertical vibration during heavy earthquakes. To
reduce this, spans should not exceed those shown in Figure
23
GOOD CONSTRUCTION
PRACTICES
Building Configuration
It is possible to improve the seismic resistance of a building by following these simple
planning principles:
• The plan shape is to be kept simple; the length to width ration should not
exceed 4. If a building longer than this is required, separation joints as shown
in Figure 2 should be introduced. The building structure should be as
symmetrical as possible along each principal axis. A sufficient number of
structural walls, with approximately the same cross-sectional area and
stiffness, should be provided in each direction of the building (Figure 18).
24
GOOD CONSTRUCTION
PRACTICES
If recesses are required, they should not exceed 25% of the overall dimension
in the corresponding direction, see Figure 19.
25
GOOD CONSTRUCTION
PRACTICES
• Number of storeys and maximum building heights are to follow the
recommendations in the table below.
The elevations should be regular (uniform), i.e. top-heavy facades where mass is
concentrated at upper storeys should be avoided as shown in Figure-21.
26
27
How Do
Unreinforced
Masonry Buildings
Behave During
Earthquakes?
Faillure of Brick Masonry Walls Wall Corner Cracking Partial Building Collapse in
in the 1997 Jabalpur Earthquake (1993 Killari Earthquake) the 1997 Jabalpur
Earthquake
Collapse of Brick Masonry Buildings
in the 2001 Bhuj Earthquake
31 Seismic Features
Seismic
Strengthening
Techniques
32
Seismic Strengthening
Techniques
33
Repairs Of
Existing 34
Construction
35
Thank You