Exam Questions

Exam Title : Chapter MEK 1

1. Boiler is related to_______________ _.

A. Steam Generation
B. Human waste
C. Storing Vegetables
D. Steering
Right Answers : A

2. Which of the following is bottom most part of a diesel engine?

A. Connecting Rod
B. Piston
C. Turbo charger
D. Exhaust valve
Right Answers : A

3. Main Engine is part of the ________________ system

A. Ballast
B. Electrical
C. Propulsion
D. Bilge
Right Answers : C

4. Domestic Fridge is related to _______________ _.

A. Human waste
B. Steering
C. Starting of Main Engine
D. Storing Vegetables
Right Answers : D

5. Which of the following is top most part of a diesel engine?

A. piston
B. cylinder head
C. crank shaft
D. crankcase door
Right Answers : B

6. Which of the following is lower most part of a diesel engine?

A. turbo charger
B. exhaust valve
C. bed plate
D. piston
Right Answers : C

7. Which of the following is within the engine room?

A. paint storage room
B. CO2 Room
C. cargo pump room
 D. purifiers room
Right Answers : D

8. Which of the following is not within the engine room?

A. fresh water generator
B. fire pump
C. fridge room
D. refrigeration machinery
Right Answers : C

9. Which of the following is not within the engine room?

A. boiler
B. mooring winch
C. air compressor
D. generator engine
Right Answers : B

10. Which of the following is not a job of an engine room rating?

A. assist in watchkeeping
B. painting engine room
C. assist in maintenance work
D. operate main engine
Right Answers : D

11. Which of the following is job of an engine room rating?

A. start and stop engine
B. overhaul air compressor
C. assist in maintenance work
D. report to bridge about engine condition
Right Answers : C

12. Boiler is related to _______________ _.

A. Storing Vegetables
B. Human waste
C. Steam Generation
D. Steering
Right Answers : C

13. Sewage Treatment Plant is related to _______________ _.

A. Starting of Main Engine
B. Steering
C. Human waste
D. Storing Vegetables
Right Answers : C

14. Identify the machinery in the following picture.

 A. A Valve
B. Water Cooler
C. Ballast pump
D. Purifier
Right Answers : A

15. Identify the machinery in the following picture.

A. Purifier
B. Water Cooler
C. Ballast pump
D. Cargo Oil Pump Turbine
Right Answers : B

16. Identify the machinery in the following picture.

A. Crankcase relief valves on Main Engine

B. Air compressor
C. Oil Filter
D. Cargo Oil Pump Turbine
Right Answers : C

17. Identify the machinery in the following picture.

A. Ballast pump
B. Cargo Oil Pump Turbine
 C. Air compressor
D. Purifier
Right Answers : D

18. Identify the machinery in the following picture

A. Purifier
B. Air compressor
C. Cargo Oil Pump Turbine
D. Ballast pump
Right Answers : B

19. Identify the machinery in the following picture

A. Air compressor
B. Cargo Oil Pump Turbine
C. Ballast pump
D. Auxiliary Engine
Right Answers : D

20. The given image is of

A. Globe valves
B. Crankcase pressure relief valves
C. Air compressor valves
D. Cylinder head valves
Right Answers : B
21. The given image is of
 A. Narrow escape
B. Broad escape
C. Emergency escape
D. Engine room space
Right Answers : C

22. What is not a system

A. Boiler
B. Purifier
C. Air compressor
D. Main Engine
Right Answers : D

Exam Title : Chapter MEK 2

1. A "BOLT" has
A. Hexagonal head and threads at other end
B. Thread at both ends
C. Slotted head and threads at other end
D. Double pitch threads
Right Answers : A

2. "Cuts" are caused by

A. Flat spanners
B. Sharp objects
C. Hammers
D. Blunt chisels
Right Answers : D

3. A DIE can be is used to make threads on a pipe

A. True
B. False
Right Answers : A

4. For lifting a heavy load, you will use

A. Eye bolt
B. Air Cylinder
C. Hydraulic Jack
D. Chain Block
Right Answers : D

5. A TAP is used to make internal threads inside a drilled hole

A. True
 B. False
Right Answers : A

6. A "STUD" has
A. Threads at one end with a slot at the other end
B. Double pitch threads
C. Hexagonal head and thread at the other end
D. Thread at both ends
Right Answers : D

7. What is the name of the item in the given picture?

 A. Chain sling
B. Chain block
C. Pulley block
D. Ratchet block
Right Answers : B

8. The following set of tools are used for making holes in

A. Steel sheet
B. Thin Plywood
C. Rubber sheet
D. Plastic sheets
Right Answers : C

9. Identify the following Tool

A. Outside calliper
B. Inside calliper
C. Jaw calliper
D. Vernier calliper
Right Answers : A

10. Identify the following Tool

A. Digital Vernier Calliper

B. Measuring Scale
C. Depth Gauge
D. Dial Gauge
Right Answers : A

11. Identify the following Tool

 A. Ball Pein hammer
B. Sledge hammer
C. Soft hammer
D. Rubber Mallet
Right Answers : D

12. Identify the following tool

A. Open jaw spanner

B. Flat spanner
C. Open ended spanner
D. Crowfoot spanner
Right Answers : D

13. Identify the following Tool

A. Adjustable Micrometer
B. Dial calliper
C. Thickness Gauge
D. Vernier calliper
Right Answers : D

14. Identify the following Tool

 A. Ratchet block
B. Pulley block
C. Swivel block
D. Chain block
Right Answers : B

15. You CANNOT use the following tool for Driving screws

A. False
B. True
Right Answers : A

16. Identify the following picture

A. Half Round fie

B. Rasp file
C. Flat File
D. Reamer
Right Answers : C

17. Identify the following Tool

A. Ball Pein Hammer

B. Soft Hammer
C. Claw Hammer
D. Sledge Hammer
Right Answers : A

18. What is the equipment used for?

 A. Sand blasting
B. Surface grinding
C. Welding flat pieces
D. Cutting pipes
Right Answers : B

19. You can use the following tool for lifting heavy parts

A. False
B. True
Right Answers : B

20. Identify the following Tool

A. Chain Spanner
B. Stubby
C. Slogging spanner
D. Ring Spanner
Right Answers : C

21. Identify the following picture

A. C Clamp
B. Leg vice
C. Bench Vice
 D. Pipe Grip
Right Answers : C

22. Identify the following Tool

A. Ball Pein hammer

B. Chipping hammer
C. Cross Pein hammer
D. Soft hammer
Right Answers : C

23. The follwoing tool is called socket spanner set

A. False
B. True
Right Answers : B

24. The given picture is of

A. Scoop thermometer
B. Digital Thermometer
C. Anemometer
D. Psychrometer
Right Answers : A

25. The given picture is of

 A. Stubby
B. Awl
C. Reamer
D. Nose Plier
Right Answers : A

26. What is the name of the following tool?

A. Crowfoot spanner
B. Adjustable spanner
C. Hammer
D. Awl
Right Answers : B

27. What is the name of the following tool?

A. pipe wrench
B. adjustable spanner
C. combination spanner
D. Crowfoot spanner
Right Answers : A

28. What is the name of the following tool?

A. double ended offset ring spanner

B. adjustable spanner
C. combination spanner
D. flare nut spanner
Right Answers : A

Exam Title : Chapter MEK 4

1. The unit of Power is
A. Cubic meters or Liters
B. Kilowatt
C. Minutes
D. Kg/cm2 or Bar
Right Answers : B

2. The instrument Needed/Provided for Measuring Length is

A. Steel scale
B. Depth gauge
C. Thermometer
D. Micrometer
Right Answers : A

3. The instrument Needed/Provided for Measuring Gearbox Oil Level is

A. Micrometer
B. Depth gauge
C. Dual pressure gauge
D. Sight Glass
Right Answers : D

4. Bar is unit for

A. pressure
B. temperature
C. mass
D. length
Right Answers : A

5. Unit of electrical current is

A. ampere
B. volt
C. ohm
D. watt
Right Answers : A

6. Sounding tape is use for checking

A. length
B. water level in the tank
C. oil level in the gear box
D. noise level
Right Answers : B

7. Which instrument is used for centering an object on the lathe chuck

A. micrometer
B. vernier callipers
C. steel scale
 D. dial gauge
Right Answers : D

8. Which instrument is used measuring diameter of circular rod

A. steel scale
B. micrometer
C. measuring tape
D. dial gauge
Right Answers : B

9. Pyrometers are commonly used for

A. exhaust temperature
B. cooling water
C. lubricating oils
D. lubricating oil pressure
Right Answers : A

10. The unit of Tank Capacity is

A. Cubic meters or Liters
B. Kilowatt
C. Kg/cm2 or Bar
D. Minutes
Right Answers : A

11. The unit of Temperature is

A. Degree Centigrade
B. Kg/cm2 or Bar
C. Cubic meters or Liters
D. Kilowatt
Right Answers : A

12. The Function of a Level Gauge is to

A. Indicate Level
B. Indicate pressure
C. Pressurize liquids
D. Separate solid and liquids
Right Answers : A

13. The instrument Needed/Provided for Measuring Diameter is

A. Micrometer
B. Dual pressure gauge
C. Depth gauge
D. Sight Glass
Right Answers : A

14. The unit of Pressure is

A. Cubic meters or Liters
B. Kg/cm2 or Bar
C. Minutes
D. Kilowatt
Right Answers : B
15. The unit of Sounding is
A. Meters and Centimeters
B. Kilowatt
C. Minutes
D. Ampere
Right Answers : A

16. What is the name of the following tool?

A. vacuum gauge
B. pressure gauge
C. Hygrometer
D. Pyrometer
Right Answers : D

17. What is the name of the following tool?

A. temperature gun
B. pressure gauge
C. Pressure Regulator
D. Thermometer
Right Answers : D

18. The given picture is of a

A. Thermometer
B. Pyrometer
C. Sight glass
D. Pocket Thermometer
Right Answers : C

19. The given picture is of a

 A. Vacuum Gauge
B. Pressure Regulator
C. Compound Gauge
D. Pressure Gauge
Right Answers : D

20. The given picture is of a

A. Pressure regulator
B. Compound Gauge
C. Vacuum Gauge
D. Pressure Gauge
Right Answers : A

21. The given picture is of a

A. Pressure Gauge
B. Vacuum Gauge
C. Pressure regulator
D. Compound Gauge
Right Answers : B

22. The given picture is of a

 A. Sight glass
B. Pyrometer
C. Pocket Thermometer
D. Gauge Glass
Right Answers : C

23. Given picture is of

A. Pressure Reducer
B. Pyrometer
C. Infrared Temperature sensor
D. Humidifier
Right Answers : C

24. The unit of sea distance is

A. Mile
B. Nautical mile
C. Kilometre
D. Knot
Right Answers : B

25. Select the correct reading

A. 27 bar
B. 28 psi
C. 29psi
D. 28 bar
Right Answers : B

26. Select the correct reading

 A. 83psi
B. 84 psi
C. 85psi
D. 84 bar
Right Answers : B

27. Select the correct reading

A. 7000kpa
B. 6000kpa
C. 6000psi
D. 4500psi
Right Answers : B

28. Select the correct reading

A. 5.23mm
B. 5.72mm
C. 4.73mm
D. 4.23mm
Right Answers : D

29. Select the correct reading

A. 15.14mm
B. 15.10mm
 C. 16.14mm
D. 16.12mm
Right Answers : C

30. Select the correct reading

A. 1.28bar
B. 1.24 kg/Cm2
C. 1.28 kg/cm2
D. 1.26 kg/cm2
Right Answers : C

31. Select the correct reading

A. 0.8 bar
B. 0.8 kg/cm2
C. 0.82 kg/cm2
D. 0.82psi
Right Answers : B

32. Select the correct reading

A. 5.10mm
B. 5.14mm
C. 5.12mm
D. 5.15mm
Right Answers : B

33. Select the correct reading.

 A. 16.12mm
B. 16.66mm
C. 16.15mm
D. 16.16mm
Right Answers : B

34. Select the correct reading

A. 5.90mm
B. 5.92mm
C. 5.93mm
D. 5.96mm
Right Answers : B

35. Given pump is used for

A. Sea water
B. Fuel oil
C. Llube oil
D. Freash water
Right Answers : A

36. The given picture is of

A. Reamer
B. Awl
 C. Screw Driver
D. Hammer
Right Answers : B

37. Given picture is of

A. Stud
B. Reamer
C. Screw
D. Bolt
Right Answers : B

38. the given picture is of

A. Compound gauge
B. Vacuum Gauge
C. Pressure regulator
D. Pressure Gauge
Right Answers : A

Exam Title : Chapter MEK 5

1. Most common use of Fire hydrant is ___________

A. Gauge glass
B. Deck water line
C. Ballast line
D. Steam line
Right Answers : B

2. The Function of Valves is to

A. Control Flow
B. Store Air
C. Ventilation
D. Remove Solid impurities from liquids
Right Answers : A

3. The Function of a Centrifugal Separator is to

 A. Pressurize liquids
B. Separate solid and liquids
C. Trap solid particles
D. Pressurize air or gases
Right Answers : B

4. What Maintenance task should be carried out on Diesel Generator Engine

A. Basket cleaning & wire mesh inspection
B. Cleaning, varnishing, baking and insulation check
C. Furnace & Tubes Cleaning & Inspection
D. Cylinder head with inlet and exhaust valves overhaul and inspection
Right Answers : D

5. Type of pump used for sea water cooling on board is

A. Centrifugal pump
B. Reciprocating pump
C. Screw pump
D. Axial flow pump
Right Answers : A

6. Impeller of centrifugal pump is fitted to

A. A Shaft
B. A gland
C. The motor
D. The casing
Right Answers : A

7. Fresh water generator is related to _____________________ _.

A. Evaporator
B. Steering
C. Storing Vegetables
 D. Starting of Main Engine
Right Answers : A

8. A cooler is a type of ________

A. Compressor
B. Heat exchanger
C. Air conditioner
D. Machine
Right Answers : B

9. Which of the following is not a type of 'Pump'?

A. Gear
B. Non return
C. Reciprocating
D. Screw
Right Answers : B

10. Function of a pump is to

A. Control flow of fluids
B. Purify fluids
C. Pressurize fluids
D. Inject fuel
Right Answers : C

11. The exhaust gas economizer on a ship is a part of the __________

A. Turbo charging
B. Oil fired boiler
C. Steam Generation System
D. Hot water system
Right Answers : C

12. Most common use of Non Return valve is ___________

A. Ballast line
B. Bilge line
C. Gauge glass
D. Steam line
Right Answers : B

13. The function of "HEAT EXCHANGERS" is to

A. Store air
B. Pressurise fluids
C. Ventilation
D. Cooling or heating
Right Answers : D

14. What Maintenance task should be carried out on Filters

A. Furnace & Tubes Cleaning & Inspection
B. Basket cleaning & wire mesh inspection
 C. Cylinder head with inlet and exhaust valves overhaul and inspection
D. Cleaning, varnishing, baking and insulation check
Right Answers : B
 15. The Function of Pumps is to
A. Remove Solid impurities from liquids
B. Control Flow
C. Pressurize Fluids
D. Ventilation
Right Answers : C

16. On board ship a fire pump is a type of

A. Centrifugal
B. Gear
C. Reciprocating
D. Screw
Right Answers : A

17. Most common use of Butterfly valve is ___________

A. Steam line
B. Deck water line
C. Ballast line
D. Gauge glass
Right Answers : C

18. Purifiers are related to _____________________ _.

A. Steering
B. Steam Generation
C. Oil
D. Evaporator
Right Answers : C

19. On board ship a bilge pump is a type of

A. Centrifugal Pump
B. Screw Pump
C. Gear Pump
D. Reciprocating Pump
Right Answers : D

20. What Maintenance task should be carried out on Oil fired Boilers
A. Cleaning, varnishing, baking and insulation check
B. Furnace & Tubes Cleaning & Inspection
C. Basket cleaning & wire mesh inspection
D. Cylinder head with inlet and exhaust valves overhaul and inspection
Right Answers : B

21. The instrument Needed/Provided for Measuring Pressure in Boiler is

A. Depth gauge
B. Pressure Regulator
C. Pressure gauge
D. Sight Glass
Right Answers : C
22. A gear pump is most suited for
A. Water
 B. Gas
C. Oil
D. Air
Right Answers : C

23. "CAM OPERATED" is an actuator for___________

A. Gate Valve
B. Exhaust Valve
C. Safety Valve
D. Globe Valve
Right Answers : B

24. Centrifugal Pump is a part of the ______________________ system.

A. Bilge
B. Propulsion
C. Fuel oil
D. Ballast
Right Answers : D

25. Main function of a Purifier on a ship is to

A. Clean bilge and ballast water before discharging
B. Purify fuels and lubricating oils
C. Remove human waste before discharging the water
D. Clean air before it enters diesel engine
Right Answers : B

26. The Function of a Valve is to

A. Pressurize air or gases
B. Pressurize liquids
C. Indicate pressure
D. Control flow of liquids or gases
Right Answers : D

27. What Maintenance task should be carried out on Valves

A. Furnace & Tubes Cleaning & Inspection
B. Inspection, grinding and gland packing renewal
C. Cylinder head with inlet and exhaust valves overhaul and inspection
D. Basket cleaning & wire mesh inspection
Right Answers : B

28. Which of the following is used to check water level in the boiler?
A. Blow down cock
B. Feed water valve
C. Indicator valve
D. Gauge glass
Right Answers : D

29. What is the common name for item used for preventing leakage from between pipe
flanges?
A. Joint
B. Lagging
 C. Washer
D. Packing
Right Answers : A

30. "SPRINGS" is an actuator for___________

A. Safety Valve
B. Gate Valve
C. Ball Valve
D. Turbo Charger
Right Answers : A

31. Boiler is a part of the _____________________ system.

A. Bilge
B. Steam generation and distribution
C. Propulsion
D. Ballast
Right Answers : B

32. Quick Closing Valves are fitted on

A. Ballast tanks
B. Generator engine
C. Air Bottles
D. Fuel tanks
Right Answers : D

33. Most common use of Spring loaded valve is ___________

A. CO2 line
B. Steam line
C. Pressure release
D. Deck water line
Right Answers : C

34. Most common use of Globe valve is ___________

A. Gauge glass
B. Ballast line
C. Steam line
D. Deck water line
Right Answers : C

35. The Function of "FILTERS" is to

A. Store Air
B. Remove Solid impurities from fuels
C. Ventilation
D. Control Flow
Right Answers : B

36. "LEVERS/HANDLES" is an actuator for___________

A. Safety Valve
B. Gate Valve
C. Glove Valve
D. Butterfly Valve / Ball Valve
Right Answers : D

37. Reciprocating Pump is a part of the ______________________ system.

A. Propulsion
B. Bilge
C. Fuel oil
D. Ballast
Right Answers : B

38. What Maintenance task should be carried out on Pumps

A. Basket cleaning & wire mesh inspection
B. Cylinder head with inlet and exhaust valves overhaul and inspection
C. Cleaning, varnishing, baking and insulation check
D. Impeller, wear rings and rotor assembly inspection
Right Answers : D

39. Oil cargo is discharged from tankers using

A. Screw pump
B. Gear pump
C. Centrifugal pump
D. Vane type pump
Right Answers : C

40. "HYDRAULIC DEVICES" is an actuator for___________

A. Relief Valves
B. Safety Valve
C. Ball Valve
D. Exhaust Valve
Right Answers : D

41. Most common use of Cock is found in ___________

A. Deck water line
B. Gauge glass
C. Ballast line
D. Steam line
Right Answers : B

42. Purifier is a part of the ______________________system.

A. Propulsion
B. Bilge
C. Ballast
D. Fuel oil
Right Answers : D

43. The Function of a pumps is to

A. Pressurize liquids
B. Trap solid particles
C. Separate solid and liquids
 D. Pressurize air or gases
Right Answers : A
44. Which of the following is not a 'Heat Exchanger'?
A. Oil heater
B. Air cooler
C. Fuel injector
D. Fridge condenser
Right Answers : C

45. Steam from a boiler is used for

A. Condenser
B. Safety valve
C. Fuel Oil Heaters
D. Feed tank
Right Answers : C

46. The instrument Needed/Provided for Measuring water level in boiler is

A. Depth gauge
B. Micrometer
C. Gauge Glass
D. Sight Glass
Right Answers : C

47. "HAND WHEELS" is an actuator for___________

A. Ball Valve
B. Safety Valve
C. Gate Valve / Globe Valve
D. Turbo Charger
Right Answers : C

48. Main Sea Water Pump used in Engine Room is a

A. Centrifugal type
B. Gear type
C. Screw type
D. Reciprocating type
Right Answers : A

49. Pump most commonly used for L.O. system of generator engines is _____________ type.
A. Screw
B. Reciprocating
C. Vane
D. Gear
Right Answers : D

50. "SOLENOID" is an actuator for___________

A. Electrically Operated
B. Safety Valve
C. Turbo Charger
D. Gate Valve
Right Answers : A
51. Boiler is related to _____________________ _.
A. Steering
 B. Storing Vegetables
C. Human waste
D. Steam Generation
Right Answers : D

52. Fresh water generator on the ships produces

A. Sea water from fresh water
B. Sea water from fresh water
C. Fresh water from sea water
D. Clean water from bilge water
Right Answers : C

53. During operation, the inner parts of a centrifugal pump

A. Reciprocates
B. Oscillates
C. Remain stationary
D. Rotates
Right Answers : D

54. Most dangerous aspect of oil fired boilers operation is

A. Fuel oil contamination with water
B. Chocking of water level Gauge-glasses
C. Black Smoke
D. White Smoke
Right Answers : B

55. How many safety valves are provided on a steam boiler

A. Four
B. One
C. Two
D. Three
Right Answers : C

56. The Function of a Filter is to

A. Trap solid particles
B. Pressurize air or gases
C. Separate solid and liquids
D. Pressurize liquids
Right Answers : A

57. How many gauge-glasses are provided on an oil fired boiler

A. One-glass type
B. Two-glass type
C. One-Electronic type
D. One-Remote type
Right Answers : B

58. The function of "PURIFIER" is to

A. Remove solid impurities
B. Remove solid impurities from water
C. Pressurise Fluids
 D. Store Air
Right Answers : A

59. Identify the following part

A. Check Valve Globe type

B. Globe Valve
C. Ball Type check valve
D. Ball Valve
Right Answers : A

60. Identify the Items "A" shown in the diagram

A. Packing Ring
B. Gland Packing
C. Globe Valve
D. Oil Purifier
Right Answers : A

61. Identify the following pump

A. Screw pump
B. Gear pump
C. Centrifugal pump
D. Reciprocating pump
Right Answers : B

62. Identify the following part

 A. Globe Valve
B. Gate Valve
C. Multi port Cock
D. Butterfly valve
Right Answers : B

63. Identify the following part

A. Gate Valve
B. Globe Valve
C. Butterfly valve
D. Multi port Cock
Right Answers : B

64. Identify the following pump

A. Screw pump
B. Gear pump
C. Centrifugal pump
D. Reciprocating pump
Right Answers : C

65. Identify the following part

 A. Check Valve Globe type
B. Globe Valve
C. Ball Type check valve
D. Ball Valve
Right Answers : C

66. The valve shown below is a Swing check valve

A. False
B. True
Right Answers : B

67. Identify the following pump

A. Gear pump
B. Centrifugal pump
C. Reciprocating pump
D. Screw pump
Right Answers : D

68. Identify the following part

A. Check Valve Globe type

B. Screw down non return valve
C. Ball Type check valve
D. Globe Valve
Right Answers : B

69. The valve shown below is a Storm valve

 A. False
B. True
Right Answers : B

70. Identify the following part

A. Metal Gasket
B. Steam gasket
C. Flange
D. Rubber Gasket
Right Answers : D

71. Identify the following part

A. Ball Valve
B. Gate Valve
C. Globe Valve
D. Butterfly valve
Right Answers : D

72. Identify the following part

A. Butterfly valve
 B. Ball Valve
C. Check Valve Globe type
D. Globe Valve
Right Answers : B

73. Macerator pump is a component of

A. Hydrophore plant
B. Bilge plant
C. Sewage plant
D. Fresh water plant
Right Answers : C

74. Given picture is of which equipment

A. Fresh water Generator

B. Hydrophore
C. Oily water separator
D. Centrifugal separator
Right Answers : C

75. Which is not the part of Fridge & Air conditioning system
A. Evaporator
B. Condenser
C. Compressor
D. Economiser
Right Answers : D

76. The given below components are of

A. Auto clean nozzle

B. Auto clean filter
C. Auto clean pump
D. Auto clean dryer
Right Answers : B

77. The given picture is of

 A. Pneumatic air gun
B. Pneumatic pump
C. Pneumatic filter
D. Pneumatic strainer
Right Answers : A

78. The given Hand pump is of the following type

A. Rotating
B. Oscillating
C. Reciprocating
D. Circulating
Right Answers : C

79. Main function of a Purifier on a ship is to

A. Clean air before it enters diesel engine
B. Purify fuels and lubricating oils
C. Clean bilge and ballast water before discharging
D. Remove human waste before discharging the water
Right Answers : B

80. Given picture is of

A. Auto washer
B. Auto clean filter
C. Auto refrigerator
D. Auto clean dryer
Right Answers : B

81. Domestic Fridge is related to _____________________ _.

A. Starting of Main Engine
B. Steering
 C. Human waste
D. Storing Vegetables
Right Answers : D

82. Identify the following Equipment/Tool.

A. Screw
B. Thread extractor
C. Tap
D. Stud
Right Answers : B

83. Identify the type of Nut

A. Prevailing torque Lock Nut

B. Hex Plain nut
C. Serrated nut
D. Wing nut
Right Answers : A

84. Which of the following is used for maintaining tightness of a nut?

A. Flat washer
B. Spring Washer
C. Screw extractor
D. Key
Right Answers : B

85. What kind of washer is shown in the picture

A. Spring washer
B. Locking Nut
C. Locking washer
 D. Plain washer
Right Answers : A

86. Identify the machinery in the following picture.

A. Ballast pump
B. Cargo Oil Pump Turbine
C. Purifier
D. Water Cooler
Right Answers : D

87. What is the person in the picture doing.

A. Pushing in the Shaft Key

B. Breaking Spline
C. Removing the Shaft key
D. Hammering the shaft
Right Answers : A

88. Engine room ventilation falls under 2 major categories. Name both of them
A. Forced Draft
B. Load Draft
C. Unbalanced Draft
D. Natural Draft
Right Answers : A,D

89. The function of Hydrophore system is to supply

A. Jacket cooling water
B. Domestic Fresh Water
C. Domestic Sea water
D. Compressed Air
Right Answers : B

90. Given picture is of

 A. Three way cock
B. Multipurpose cock
C. Two way cock
D. Ball valve
Right Answers : A

Exam Title : Chapter MEK 7

1. Which of this is not fitted on the cylinder head of a diesel engine

A. exhaust valve
B. turbo charger
C. starting valve
D. indicator valve
Right Answers : B

2. Which of this is not a moving part of a diesel engine

A. piston
B. crankshaft
C. crankcase
D. connecting rod
Right Answers : C

3. Generator engine on board ship is started using

A. hydraulic oil motors/pressure
B. compressed air
C. turbo generator
D. air compressor
Right Answers : B

4. Purpose of fresh water circulation through diesel engine cylinder is to

A. prevent corrosion
B. remove heat of combustion
C. clean exhaust gases
D. lubricate moving part
Right Answers : B

5. Turning gear on main engine is provided for

A. releasing parts if jammed
B. turning the engine during overhaul
C. remove exhaus gases from cylinder
D. ensure turning of propeller
Right Answers : B

6. Exhaust gas economiser produces

A. fresh water
 B. steam
C. inert gas
D. electricity
Right Answers : B

7. Turbo chargers on diesel engine

A. acts as fuel charger
B. decreases the pressure of intake air
C. increases pressure of intake air
 D. increases RPM
Right Answers : C

8. Exhaust gases from the main engine go to the atmosphere through

A. inert gasgenerator
B. oil fired boiler
C. exhaust fan
D. exhaust gas boiler
Right Answers : D

9. Relief valves are provided on main engine cylinders for protection against high
A. pressure
B. exhaust temperature
C. speed
D. level of water
Right Answers : A

10. Function of a cylinder head relief valve is to

A. prevent crankcase explosion
B. stop the engine
C. reduce the speed of engine
D. release excessive pressure
Right Answers : D

11. Function of crankcase relief door is to

A. release pressure from crankcase
B. stop the engine
C. reduce the speed of engine
D. detect the mist inside the crankcase
Right Answers : A

12. If cooling water becomes less in a diesel engine the engine will
A. make more noise
B. cool down too much
C. get overheated
D. not start
Right Answers : C

13. Diesel engine bearing will get damaged if supply of _______________ is not enough
A. air
B. fuel
C. water
D. lubricating oil
Right Answers : D

14. Speed of diesel engine is adjusted by changing the supply of

A. air
B. fuel
C. water
D. lubricating oil
Right Answers : B
15. While diesel engine is operating ,one of the important pressure to check is ______
A. lubricating ol
B. sarting air
C. exhaust gas
D. steam pressure
Right Answers : A

16. One of the function of lubricating oil in a diesel engine is to reduce

A. exhaust temperatures
B. friction between moving parts
C. wexhaust gases
D. weight of the engine
Right Answers : B

17. Function of crankcase lubricating oil in a diesel engine is to ____

A. improve combustion
B. prevent corrosion
C. supply power
D. turn crankshaft
Right Answers : B

18. The lower most ring on a diesel engine piston is called

A. split ring
B. compression ring
C. pressure ring
D. oil scraper ring
Right Answers : D

19. For good combustion,the color of the exhaust from diesel engine should be
A. light brown
B. colourless
C. light grey
D. bluish white
Right Answers : B

20. Ships propeller is fitted to

A. stern tube
B. intermediate shaft
C. tail shaft
D. crankshaft
Right Answers : C

21. The type of engine normally used for generators on a ship is ____________
A. 4 stroke
B. 2 stroke
C. 6 stroke
D. medium stroke
Right Answers : A

22. When starting engine on diesel oil, before injection the oil is
A. heated to same temp s heavy oil
 B. heated if necessary in cold climate
C. passed through the purifier
D. mixed with steam
Right Answers : B

23. A cam shaft on diesel engine operates

A. fuel injection pump
B. flywheel
C. fuel valves
D. starting valves
Right Answers : A

24. Thrust block for main engine is fitted at the

A. forward side of engine
B. aft side of engine
C. end of the cam shaft
D. tail shaft
Right Answers : B

25. Function of a cylinder head relief valve is to

A. Release excessive pressure
B. Reduce the speed of the engine
C. Stop the engine
D. Prevent crankcase explosion
Right Answers : A

26. The purpose of Injector valve on a generator engine is for ___________________.

A. Safety
B. Fresh air intake
C. Fuel inlet
D. Compress air
Right Answers : C

27. Exhaust valve in a Diesel engine _____________ _.

A. Stays in place
B. Opens and closes
C. Rotates in place
D. Moves up and down
Right Answers : B

28. Thrust block for main engine is fitted at the

A. End of the cam shaft
B. Tail Shaft
C. Forward side of Engine
D. Aft side of Engine
Right Answers : D

29. Piston in a Diesel engine_____________ _.

A. Stays in place
B. Moves up and down
C. Oscillates
 D. Rotates in place
Right Answers : B

30. The purpose of Exhaust Gas in a Diesel engine is to ______________ _.

A. Reduces friction
B. Increases air supply
C. Turns turbo charger
D. Gives power
Right Answers : C

31. What is to be checked on a running Main engine , during watch.

A. Exhaust temperature
B. Oil coming out of water side
C. Steering angle
D. Discharge pressure of liquid
Right Answers : A

32. Air starting valve in a Diesel engine ____________ _.

A. Oscillates
B. Moves up and down
C. Moves from side to side
D. Opens only at engine starting
Right Answers : D

33. The purpose of Indicator valve on a generator engine is for ___________________.

A. Fresh air intake
B. Compressed air
C. Blowing through
D. Fuel inlet
Right Answers : C

34. Which of these is NOT a moving part of a diesel engine:

A. Crankcase
B. Connecting rod
C. Piston
D. Crankshaft
Right Answers : A

35. Cylinder Head in a Diesel engine ____________ _.

A. Oscillates
B. Rotates in place
C. Moves up and down
D. Stays in place
Right Answers : D

36. The purpose of Inlet valve on a generator engine is for ___________________.

A. Safety
B. Fresh air intake
C. Compress air
D. Fuel inlet
Right Answers : B
37. The purpose of Exhaust valve on a generator engine is for ___________________.
A. Combustion Gases
B. Stop fuel
C. Fuel inlet
D. Fresh air intake
Right Answers : A

38. Before starting a generator engine, LO hand pump should be operated to

A. Warm up the engine
B. Supply lub oil to moving parts
C. Check the level of the tank
D. Turn the engine
Right Answers : B

39. Connecting rod in a Diesel engine ____________ _.

A. Moves up and down
B. Stays in place
C. Oscillates
D. Rotates in place
Right Answers : C

40. The purpose of Fuel Oil in a Diesel engine is to ______________ _.

A. Reduces friction
B. Gives power
C. Turns turbo charger
D. Causes explosion
Right Answers : B

41. The purpose of Lubricating Oil in a Diesel engine is to ______________ _.

A. Increases air supply
B. Reduces friction
C. Turns turbo charger
D. Gives power
Right Answers : B

42. Crankshaft in a Diesel engine ____________ _.

A. Rotates in place
B. Oscillates
C. Moves up and down
D. Stays in place
Right Answers : A

43. The purpose of "COMPRESSED AIR" in a diesel engine is to_________________

A. Turns turbo Charger
B. Starts Engine
C. Gives Power
D. Controls fuel Supply
Right Answers : B

44. Generator engine on board ships is started using

A. Compressed air
 B. Air compressor
C. Hydraulic Oil Motors / Pressure
D. Turbo generator
Right Answers : A

45. Identify parts 1 , 2 , 3 , 4 and 5 . from the following drawing

A. Connecting Rod
B. Crank Pin
C. Piston
D. Cylinder head cover
E. Rocker arm
F. Piston Ring
G. Push Rod
H. Inlet valve
Right Answers : C,D,E,F,G

46. Identify parts 6 , 7 , 8, 9 and 10. from the following drawing

A. Piston
B. Inlet Valve
C. Dip Stick/ Oil level gauge
D. Crank Pin
E. Bottom end Bearing
F. Piston ring
G. Connecting Rod
H. Push Rod
I. Rocker arm
Right Answers : B,C,D,E,G

47. Trunk type engines have Piston rod between Piston and Connecting Rod
A. False
B. True
Right Answers : A

48. Cross head type engines doesn't have Piston Rod between Piston and Connecting Rod
A. False
B. True
Right Answers : A
49. Given picture is of

A. Jacket water cooling pump

B. Turbocharger Gas side
C. Turbocharger Air inlet side
D. Lubricating oil pump
Right Answers : C

50. Given picture is of

A. Cylinder head
B. Turbocharger Gas side
C. Jacket cooling water pump
D. Turbocharger air inlet side
Right Answers : B

51. Function of crankcase lubricating oil in a diesel engine is to reduce friction between
moving parts, cooling the parts and to ____________________ _.
A. Prevent corrosion
B. Supply power
C. Turn the crankshaft
D. Improve combustion
Right Answers : A

52. The purpose of Turbocharger in a Diesel engine is to ______________ _.

A. Reduces friction
B. Increase air supply
C. Gives power
D. Turns turbo charger
Right Answers : B

53. Turbo Alternator is a generator operating on steam produced from waste heat of Main
engine exhaust gases
A. False
B. True
Right Answers : B

54. Why diesel engine generator does not have a reversing mechanism
A. Running reverse its phase sequence will change
 B. Running reverse it produces DC instead of AC
C. Running reverse it consumes power instead of producing power
D. Running reverse does not produce power
Right Answers : C

55. Which system is not required for main engine

A. Feed system
B. Lubricating system
C. Cooling system
D. Fuel system
Right Answers : A

56. Steam turbine driven generator is called

A. Shaft generator
B. Turbo alternator
C. Generator
D. Alternator
Right Answers : B

57. Main engine is part of ____________ system

A. feed water
B. Electricity generation
C. Bilge
D. Propulsion
Right Answers : D

58. Given picture is of

A. Snap ring
B. Slotted ring
C. Piston ring
D. Spring ring
Right Answers : A

Exam Title : Chapter MEK 8

1. What Maintenance task should be carried out on Air Compressors

A. First & second stage valves overhaul and inspection
B. Cylinder head with inlet and exhaust valves overhaul and inspection
C. Cleaning, varnishing, baking and insulation check
D. Basket cleaning & wire mesh inspection
Right Answers : A

2. Air Compressor is part of the________________ system.

A. Ballast
 B. Fuel oil
C. Compressed air
D. Electrical
Right Answers : C

3. The Function of a Compressor is to

A. Pressurize liquids
B. Pressurize air or gases
C. Separate solid and liquids
D. Trap solid particles
Right Answers : B

4. The function of "AIR BOTTLE" is to

A. Ventilation
B. Store Air
C. Cooling or heating
D. Control Flow
Right Answers : B

5. Which of the following is NOT a part of an air compressor?

A. Shaft
B. Filter
C. Valve
D. Injector
Right Answers : D

6. Air compressor is related to________________ _.

A. Starting of Main Engine
B. Storing Vegetables
C. Steering
D. Human waste
Right Answers : A

7. Before starting an air compressor you will ensure that

A. Fuel tank has fuel
B. Valves on discharge line are open
C. Valves are overhauled
 D. Hot work permit is taken
Right Answers : B

8. The purpose of "COMPRESSED AIR" in a diesel engine is to_________________

A. Gives Power
B. Controls fuel Supply
C. Starts Engine
D. Turns turbo Charger
Right Answers : C

9. What is to be checked on a running Air compressor , during watch.

A. Exhaust temperature
B. Oil coming out of water side
C. Air Bottle Pressure
D. Discharge pressure of liquid
Right Answers : C

10. Identify the machinery in the following picture.

A. Purifier
B. Air compressor
C. Cargo Oil Pump Turbine
D. Ballast pump
Right Answers : B

11. Common fittings on an Air bottle...Mark the incorrect one

A. Drain Valve
B. Pressure Gauge
C. Gauge glass
D. Filling Valve
Right Answers : C

12. Checks during running of an Air compressor. ..... Mark the incorrect one
A. Lube oil pressure is correct and in limits
B. Filling valve for the air bottle is closed
C. Compressor is drawing normal amps
D. Check for any noise and vibrations
Right Answers : B

13. Which of the following is not the function of Compressed Air

A. Starting of Main engine
B. Cleaning of machinery parts
C. Cleaning of Individual's body parts
D. Operation of hand tools
Right Answers : C

14. Drain valves are provided on the air bottles to remove

A. Fuel
B. Lube oil
C. Condensed water
D. Steam
Right Answers : C

Exam Title : Chapter MEK 9

1. What Machine Tool will you be Using for Making Axial hole in a Round bar.
A. Bending machine
B. Grinding machine
C. Drill machine
D. Lathe machine
Right Answers : D

2. What Machine Tool will you be Using for Cutting a joint.

A. Lathe machine
B. Bending machine
C. Drill machine
D. Scissors
Right Answers : D

3. What machine will you use for cutting a large plate?

A. Welding Machine
B. Drill Machine
C. Gas Cutting Machine
D. Grinding Machine
Right Answers : C

4. What Machine Tool will you be Using for Joining two plates.
A. Drill machine
B. Lathe machine
C. Grinding machine
D. Welding machine
Right Answers : D

5. What Machine Tool will you be Using for Making holes in a plate.
A. Grinding machine
B. Drill machine
C. Bending machine
D. Lathe machine
Right Answers : B

6. To make a new flange for a pipe you will need:

A. Chisel, hammer and drilling machine
B. Lathe machine and drilling machine
C. Grinding machine, drilling machine and pipe cutter
D. Welding machine and milling machine
Right Answers : B

7. Which of these is NOT a part of a lathe

A. Anvil
B. Head stock
C. Tool post
 D. Chuck
Right Answers : A

8. What Machine Tool will you be Using for Removing extra material after welding.
A. Drill machine
B. Lathe machine
C. Grinding machine
D. Bending machine
Right Answers : C

9. During lathe work, goggles protect our eyes from __________

A. Fumes
B. Heat
C. Metal chips
D. Flash Light
Right Answers : C

10. Danger for lifting heavy equipment manually is _____________

A. slip
B. fall
C. sprain
D. fracture
Right Answers : C

11. Identify the parts numbered 1, 2, 3, 4 and 5.

A. Threading Dial
B. Cross Lever Feed
C. Longitudinal Feed Lever
D. Carriage Lock Screw
E. Cross Feed Hand wheel
F. Half Nut Lever
G. Carriage Handle
H. Tool Post Slide Hand wheel
I. Tool Post
Right Answers : A,B,C,F,G

12. Identify parts numbered 1, 2, 3, 4, and 5

 A. Drill Feed
B. Motor
C. Base
D. Step cone Pulley
E. Spindle Head
F. Spindle
G. Drill
H. Table
I. Column
Right Answers : C,E,F,G,H

13. Identify the following image

A. Flying disc
B. Rubber wheels
C. Grinding wheel
D. Abrasive disc
Right Answers : D

14. Identify parts numbered 6, 7, 8, 9, and 10

A. Drill Feed
B. Belt
C. Step cone Pulley
D. Motor
E. Base
F. Spindle Head
G. Handle
H. Column
Right Answers : A,B,C,D,H

15. Identify parts numbered 1, 2, 3, 4, and 5

 A. Base
B. Motor
C. Wheel Guard
D. Tool Rest
E. Spark Guard
F. Start Switch
G. Light Switch
H. Stop Switch
I. Safety Glass Shield
Right Answers : D,E,F,G,I

16. Identify parts numbered 6, 7, 8, 9, and 10

A. Motor
B. Dust collector
C. Wheel
D. Stop Switch
E. Base
F. Tool Rest
G. Wheel Guard
H. Spark Guard
Right Answers : A,B,C,D,G

17. Identify the parts numbered 6, 7, 8, and 9

A. Cross Feed Hand wheel

B. Carriage Lock Screw
C. Tool Post Slide Hand wheel
D. Tool Post
E. Threading Dial
F. Cross Lever Feed
G. Half Nut Lever
H. Carriage Handle
Right Answers : A,B,C,D

18. DO'S on Machine safety...Mark the incorrect one

A. Keep machine clean and in good condition
B. Check wheel rotation after running of machine
C. Switch off machine immediately if anything goes wrong
 D. Check oil levels of machine before starting
Right Answers : B

19. DONT'S in the workshop...Mark the incorrect one

A. Do not throw things or play practical jokes
B. Do leave your machine unattended
C. Do not run in the workshop
D. Do not touch any equipment unless authorised to do so
Right Answers : B

20. While working with machines do not wash your hands with coolant
A. False
B. True
Right Answers : B

Exam Title : Chapter MEK 10

1. What machine will you use for cutting a large plate?

A. Welding Machine
B. Drill Machine
C. Gas Cutting Machine
D. Grinding Machine
Right Answers : C

2. What Machine Tool will you be Using for Joining two plates.
A. Drill machine
B. Lathe machine
C. Grinding machine
D. Welding machine
Right Answers : D

3. When starting to weld you must hold the electrode at an angle of about?
A. 50°

B. 70°

C. 30°

D. 90°

Right Answers : B

4. Oxygen and ________ is used in gas welding on board.

A. Argon
B. Acetylene
C. Nitrogen
D. LPG
Right Answers : B

5. What Machine Tool will you be Using for Removing extra material after welding.
A. Drill machine
B. Lathe machine
 C. Grinding machine
D. Bending machine
Right Answers : C

6. Before starting arc welding you must:

A. Extend the welding cables
B. Connect the electrode holder to the earth clamp
C. Connect the welding cable to the earth clamp
D. Connect the earth Clamp to the work piece
Right Answers : D

7. Gases used in gas welding are

A. Acetylene and oxygen
B. CO2 and LPG
C. Oxygen and LPG
 D. Acetylene and LPG
Right Answers : A

8. The welding arc length should be:

A. Equal to the diameter of the electrode
B. Less than the diameter of the electrode
C. 20mm
D. 6-12mm
Right Answers : A

9. Identify the Part No D, E, F in the picture from the below answers

A. Oxygen Hose
B. Acetylene Hose
C. Twin Hose
D. Working Pressure Gauge
E. Oxygen Regulator
F. Cylinder Pressure Gauge
Right Answers : D,E,F

10. Identify the following image

A. Fuel gas welding nozzles

B. Flash back arrester
C. Tip cleaner
D. Gas saver lighter
Right Answers : C

11. Identify the Part No A, B, C in the picture from the below answers

A. Oxygen Cylinder
B. Twin Hose
 C. Acetylene Cylinder
D. Acetylene Hose
E. Oxygen Hose
F. Oxygen Regulator
Right Answers : A,C,E

12. Identify the Part No G, H, I in the picture from the below answers

A. Acetylene V/V Wrench

B. Oxygen Regulator
C. Twin Hose
D. Tip
E. Oxygen Hose
F. Welding Torch
Right Answers : D,E,F

13. The function of Electrode dryer is to wet the electrodes that have been exposed to a
humid atmosphere
A. False
B. True
Right Answers : A

14. Too long an arc will cause

A. This is bulb up the weld pool
B. Low penetration coarse splatter & flat bead
C. Uncontrolled penetration slag globules electrode stuck to weld
D. Even bead & good penetration & good welding
Right Answers : B

15. Too short an arc length will cause an uneven bead due to arc failure
A. None of the above
B. Good welding
C. Low penetration coarse splatter
D. Flat bead
Right Answers : A

16. Electrode should be kept at a distance of ___________ above the spot where we wish to strike
the arc
A. 30-40 mm

B. 20-30 mm

C. 40-50 mm

D. 35-45 mm
Right Answers : B
17. Welding gloves made from tanned leather can be following combinations
A. 3-finger and 5-finger type
B. 2-finger and 4-finger type
C. 4-finger and 6-finger type
D. 1-finger and 2-finger type
Right Answers : A

18. Spats protect the ankles from melted metal and splatter
A. True
B. False
Right Answers : A

19. In welding screen, welding glasses are always used with Protective glasses
A. False
B. True
Right Answers : B

20. The given picture is of

A. Gas pipe connector

B. Gas pipe adoptor
C. Gas torch union
D. Flashback arrester
Right Answers : D

21. Given picture is of

A. Gas mixing unit

B. Gas cutter
C. Hand torch
D. Welding torch
Right Answers : D

Exam Title : Chapter MEK 12

1. The level measuring device, Gauge glass & can be used for
A. Tanks of large depth
B. Multi Purpose
C. Tanks of Small depths
 D. Oil can
Right Answers : C

2. The level measuring device, Level Indicator can be used for

A. Oil level in generator crankcase
B. Sumps of purifiers, compressors, etc
C. Oil can
D. Small to large tanks within the engine room
Right Answers : B

3. The level measuring device, Sounding tape can be used for

A. Oil can
B. Tanks of large depth
C. Multi Purpose
D. Oil level in generator crankcase
Right Answers : B

4. The level measuring device, Remote level indicators can be used for
A. Multi Purpose
B. Oil can
C. Tanks of large depth
D. Oil level in generator crankcase
Right Answers : A

5. A sounding tape is used for measuring level of a liquid in a:

A. Tank
B. Boiler
C. Crank case
D. Cylinder
Right Answers : A

6. A gauge-glass for checking liquid level is fitted on which tanks

A. Fore Peak Ballast Tank
B. FO Storage Double Bottom Tank
C. After Peak Ballast Tank
D. Lub Oil Storage Tank
Right Answers : D

7. A dip stick is used for checking level of oil in a

A. Filter
B. Tank
C. Cylinder
 D. Crank case
Right Answers : D

8. The level measuring device, Dip stick can be used for

A. Multi Purpose
B. Oil level in generator crankcase
C. Tanks of large depth
D. Oil can
Right Answers : B

9. The level measuring device, Sounding rod can be used for

A. Oil can
B. Tanks of large depth
C. Oil level in generator crankcase
D. Multi Purpose
Right Answers : D

10. The most common item provided for checking oil level in a small machine is
A. Sounding tape
B. Sounding rod
C. Sight glass
D. Remote level indicator
Right Answers : C

11. Identify the picture given below

A. Sounding tape
B. Level gauge
C. Sounding rod
D. Dip stick
Right Answers : D

12.
Identify the picture given below

A. Tank filling pipe

B. Sounding pipe with Cock
C. Portable oil pump
D. Fresh water pipe with valve
Right Answers : B

13. Identify the picture given below

A. Sight glass
B. Remote level indicator
C. Level Gauge
D. Dip stick
Right Answers : C

14. Identify the picture given below

A. Sounding_tape
B. UTI Tape
C. Dip Stick
D. Sounds Rod
Right Answers : D

15. Identify the picture given below

A. Oil level gauge

B. level gauges
C. boiler level gauge glass
D. level gauge for large tanks GS
Right Answers : A

16. Identify the picture given below

 A. Long tape
B. Steel tape
C. Sounding tape
D. Measuring tape
Right Answers : C

17. Identify part 1 in the picture from the below answers

A. Level Gauge
B. Remote level indicator
C. Sight glass
D. Low level alarm
Right Answers : A

18. Identify part 2 in the picture from the below answers

A. Low level alarm

B. Level Gauge
C. Sight glass
D. Remote level indicator
Right Answers : A

Exam Title : Chapter MEK 13

1. What material is not a commonly used as insulation material?

A. Plastic
B. Wood
C. Glass Wool
D. Fire Bricks
Right Answers : A

2. What is used to prevent the transfer of heat from pipes or equipment?

 A. Insulating material
B. Cooling system
C. Turbo charger
D. Air circulation
Right Answers : A

3. What is the common name for item used for preventing the loss of heat from pipes or equipment?
A. Lagging
B. Cooling system
C. Exhaust boiler
D. Air circulation
Right Answers : A

4. What materials are banned for use as insulation materials?

A. Fire Bricks
B. Thermocole
C. Fiberglass Wool
D. Asbestos
Right Answers : D

5. Woolen garments, blankets and quilts are termed as Insulating Materials

A. True
B. False
Right Answers : A

6. While working with Insulating material such as glass wool, you must not protect your body using
gloves and goggles
A. True
B. False
Right Answers : B

7. Lagging is the Insulating material wrapped around pipes, boilers or tanks to allow loss of heat
A. True
B. False
Right Answers : B
 8. Electrical Insulation prevent flow of ......
A. Power
B. Resistance
C. Electricity
D. Voltage
Right Answers : C

9. While assembling pipes, take care in removing the lagging and putting it back after
completing the work
A. True
B. False
Right Answers : B

10. Insulating material used is generally Fire resistant

A. True
B. False
Right Answers : A

Exam Title : Chapter MEK 14

1. Chemicals should be stored in ____________

A. in accommodation
B. in engine room
C. in separate well ventilated store
D. on deck
Right Answers : C

2. If any chemical fall on the body, first action should be

A. apply medicine to affected area
B. wipe clean the affected area
C. call for the doctor
D. thoroughly wash affected area
Right Answers : D

3. Chemicals on-board are not to be used for

A. cleaning the boiler
B. cleaning the cooking utensils
C. boiler water treatment
D. fuel oil treatment
Right Answers : B

4. Disposal of used/expired chemical container should be done by

A. throwin into deep sea
B. disposal with ships garbage
C. disposal as per makers instruction
D. burning in incinerator
Right Answers : C
5. Identify the following

A. Sign for pyrotechnics

B. Sign for chemistry Lab
C. Sign for chemical danger
D. Sign for Fire danger
Right Answers : C

6. Identify the following

 A. Chemical splash roof goggles
B. Dust protection eye wear
C. normal working goggles
D. Sun protection shades
Right Answers : A

7. The image below is of chemical containers

A. True
B. False
Right Answers : A

8. Identify the following

A. Calf skin gloves

B. Cotton gloves
C. Latex hand gloves
D. Welding gloves
Right Answers : C

9. Chemicals are mainly used for

A. All of the above
B. Fuel treatment
C. Boilers
D. Testing quality of water
Right Answers : A

10. Use of personal protective gear while handling chemicals...Mark the incorrect one
A. Face mask
B. Apron
C. Rubber gloves
 D. Sun protect Goggles
Right Answers : D

Exam Title : Chapter MEK 15

1. Steering gear is used to turn the

A. crane boom/jib
B. main engine
C. propeller
D. rudder
Right Answers : D

2. Steering gear is located in the

A. forward of engine room
B. on the bridge
C. in a separate compartment aft of engine room
D. forecastle
Right Answers : C

3. Rudder of the ship is turned by means of a

A. hydraulic pump
B. propeller
C. Cylinder and Ram arrangement only
D. steering wheel
Right Answers : C

4. Which of the following is a correct statement

A. Steering gear is located at aft part of the ship
B. Rudder is connected to the propeller
C. Rudder is located in the steering flat
D. Propeller is turned by the rudder
Right Answers : A

5. Various components of Steering Gear ...Tick the incorrect one

A. Hydrophore Unit
B. Actuating Unit
C. Power Unit
D. Control Unit
Right Answers : A

6. The thruster placed in the aft of the ship is called Bow Thruster
A. False
B. True
Right Answers : A

7. The thruster placed in the forward end of the ship is called Stern Thruster
A. True
B. False
Right Answers : B

8. While taking rounds in the Steering flat, following to be checked...Mark the incorrect
one
A. Leakages from pumps, pipe joints, etc
B. Load of the pump in Ampere
C. Oil level of MDO in the steering gear system
D. Abnormal noise or vibrations
Right Answers : C

Exam Title : Chapter MEK 16

1. A quick closing valve is fitted on

A. boiler steam line
B. main engine cooling system
C. fuel tanks above double bottom tanks
D. compressed air line
Right Answers : C

2. Man hole door on a tank is fitted for

A. allowing entry to the tank when needed
B. preventing entry by unauthorized persons
C. preventing damage on tanks
D. strengthening the tank
Right Answers : A

3. A quick closing valve

A. prevents fire from occuring
B. can be remotely closed in an emergency
C. prevents oil spills in engine room
D. stops air supply to main engine
Right Answers : B

4. Air vent to tanks is provided for

A. preventing build up of pressure or vaccum
B. allowing liquid to come out when tank is full
C. preventing fire
D. for ventilation
Right Answers : A

5. Sounding pipes on tanks are fitted for finding

A. level of liquid in the tank
B. pressure in the tank
C. temperature in the tank
D. abnormal sound in the tank
Right Answers : A

6. Quick closing valve operation is carried out from

A. a remote location outside engine room
B. anywhere in the engine room
C. steering flat
D. navigation bridge
Right Answers : A
7. Ballast tank on a ship are filled up with _________
A. drinking water
B. sea water
C. cargo oil
 D. water from other tanks
Right Answers : B

8. Settling tanks on ship are provided for

A. allowing water and sludge to separate before oil seperator
B. mixing oils before use
C. storing oils before its use
D. filtering water from fuel oil
Right Answers : A

9. While bunkering is going on, what will be the most important thing to monitor
A. Oil sample is being taken
B. Temperature of oil being supplied
C. Oil sounding in the tank being filled
D. Oil sounding in bunker barge
Right Answers : C

10. Quick Closing Valves can be operated...

A. All of the above
B. Locally
C. Pneumatically
D. Remotely
Right Answers : A

11. Each tank is required to have at least the following

A. All of the above
B. Outlet Line
C. Air Vent
D. Sounding Pipe
E. Filling Connection
Right Answers : A

12. Storage Tank in the engine room will be called as _______if the tank capacity is in
between 2-50 tonnes
A. Ballast Tank
B. Medium Tank
C. Large Tank
D. Small Tank
Right Answers : D

Exam Title : Chapter MEK 17

1. On finding an injured person in the engine room, your first action will be to
A. apply first aid
B. report to the duty officer on watch
C. bring a stretcher
D. look for the cause of injury
Right Answers : B

2. A fire alarm in the engineroom is activated

 A. from the bridge
B. automatically on machinery failure
C. due to a black out
D. due to fire in the engine room
Right Answers : D

3. On hearing a CO2 alarm in the engine room, your first action will be
A. report to the duty officer on watch
B. use large fire extinguisher on the fire
C. use emergency exit to get out
D. raise fire alarm
Right Answers : C

4. A machinery failure alarm in the engine room is activated

A. from the bridge
B. automatically on machinery failure
C. due to collision of the ship
D. due to fire in the engine room
Right Answers : B

5. A general alarm is activated

A. from the bridge
B. automatically on machinery failure
C. due to black out
D. due to high bilge level
Right Answers : A

6. UMS stands for

A. Uniform Machinery Space Operation
B. Unattended Machinery Space Operation
C. Undermanned Machinery Space Operation
D. Under Machinery Space Operation
Right Answers : B

7. Accident can't happen in the engine room due to falling objects

A. False
B. True
Right Answers : A
8. Which of the following is NOT an audio visual alram
A. Fire Alarm
B. Co2 Alarm
C. Ship security alarm
D. Machinery Alarm
Right Answers : C

9. General Alarm and Co2 alarm are same

A. True
B. False
Right Answers : B

10. Emergencies that can occur in the Engine room

A. Stoppage of Main engine
B. Crank case explosion
C. Flooding of the engine room
D. All of the above
Right Answers : D

Exam Title : Chapter MEK 18

1. Identify the following

A. Fire Geometry
B. Fire square
C. Fire triangle
D. Explosive limits
Right Answers : B

2. Identify the following

A. Fixed fire fighting system

B. Fire hoses
C. Fire hydrant
D. Nozzles
Right Answers : D
3. Identify the following

A. Brass coupling
B. Flexible coupling
C. Adjustable coupling
D. International shore coupling
Right Answers : D

4. Identify the following

 A. Dry chemical type extinguisher
B. Mobile Foam extinguisher
C. Portable foam extinguisher
D. CO2 fire extinguisher
Right Answers : A

5. Identify the following

A. Dry chemical type extinguisher

B. Portable foam extinguisher
C. Mobile Foam extinguisher
D. CO2 fire extinguisher
Right Answers : D

6. Fixed fire fighting system for engine room

A. DCP
B. CO2
C. inert gas
D. nitrogen
Right Answers : B

7. Not a part of a fire triangle

A. fuel
B. heat
C. electricity
D. air
Right Answers : C

8. Main fire pump is located

A. on main deck
B. at the fire station
C. in the engine room
D. in the steering flat
Right Answers : C

9. To fight an electric fire you would use

A. dry powder
B. steam jet
C. water spray
D. special foam
Right Answers : A

10. Means of forcing water out of a portable extinguisher

A. CO2 cartridge
B. air cartridge
C. chemical cartridge
D. nitrogen cartridge
Right Answers : A

11. High expansion foam system is suitable for fighting fires in

A. accommodation
B. cargo holds
C. engine room
D. deck of ship
Right Answers : C

12. Which of the following provided for connecting to shore water supply
A. foam tank
B. fixed foam system
C. fire hydrant
D. international shore connection
Right Answers : D

13. The emergency fire pump on a ship is located

A. at the poop deck
B. inside the engine room
C. outside the engine room
D. at the boat deck
Right Answers : C

14. Your first action upon finding a fire

A. use portable extinguisher
B. start the fire pump
C. raise an alarm
D. switch off electrical power supply
Right Answers : C

15. Fire hose on ship are made of

A. strong canvas
B. thick cloth
C. leather
D. flexible teel
Right Answers : A

16. What is used in case the fire in the engine room becomes out of control
A. portable fire extinguisher
B. 45 liters foam fire extinguisher
 C. fixed CO2 fire extinguishing system
D. fire pumps and hoses
Right Answers : C
17. Which one of the following will be used first on a small fire in the engine room
A. portable fire extinguisher
B. fire blancket
C. fixed fire extinguishing system
D. fire pumps and hoses
Right Answers : A

18. Identify the following

A. Portable foam extinguisher

B. Dry chemical type extinguisher
C. CO2 fire extinguisher
D. Mobile Foam extinguisher
Right Answers : D

19. Full form of PASS. .... Mark the correct one

A. Pull, Aim, Smoke,
B. Pull, Aim, Squeeze, Sweep
C. Pull, Aim, Sponge, Sweep
D. Push, Automatic, Sweep, Squeeze
Right Answers : B

20. Following is not a part of Fire detection system

A. Heat Detector
B. Flame Detector
C. Body Detector
D. Smoke Detector
Right Answers : C

21. Identify the following

A. Fire Hydrant, Fire Hose, International Shore Coupling

B. Pipe, Fire Hydrant, Nozzle
C. Pipe, Combination nozzle, Fire Hose
D. Fire Hydrant, Fire Hose, Nozzle
Right Answers : D
Exam Title : Chapter MEK 19

1. What is to be checked on a running Main engine , during watch.

A. Exhaust temperature
B. Oil coming out of water side
C. Discharge pressure of liquid
D. Steering angle
Right Answers : A

2. While keeping a watch what will you check on a pump that is in operation
A. Suction and discharge pressure
B. Line Valves are Open
C. Temperature of liquid
D. Speed
Right Answers : A

3. While the boiler is operating, you will ensure that

A. Vent valve is open
B. Water level is maintained
C. Safety Alarms by-passed
D. Black Smoke is coming out
Right Answers : B

4. What is to be checked on a running Purifier , during watch.

A. Oil coming out of water side
B. Steering angle
C. Exhaust temperature
D. Discharge pressure of liquid
Right Answers : A

5. What is to be checked on a running Pump , during watch.

A. Oil coming out of water side
B. Exhaust temperature
C. Steering angle
D. Discharge pressure of liquid
Right Answers : D

6. While bunkering is going on, what will be the most important thing to monitor
A. Temperature of oil being supplied
B. Oil sounding in bunker barge
C. Oil sounding in the tank being filled
D. Oil sample is being taken
Right Answers : C

7. What is to be checked on a running Boiler , during watch.

A. Exhaust temperature
B. Steering angle
C. Water level
 D. Oil coming out of water side
Right Answers : C

8. Before starting an air compressor you will ensure that

A. Fuel tank has fuel
B. Valves on discharge line are open
C. Valves are overhauled
D. Hot work permit is taken
Right Answers : B

9. UMS stands for

A. Under Machinery Space Operation
B. Undermanned Machinery Space Operation
C. Unattended Machinery Space Operation
D. Uniform Machinery Space Operation
Right Answers : C

10. What is to be checked on a running Oil Transfer Pump , during watch.

A. Weather conditions
B. Level in the tank
C. Water level
D. Oil coming out of water side
Right Answers : B

11. While a diesel engine is operating, one of the important pressures to check is ___
A. Starting air
B. Exhaust Gas
C. Lubricating oil
D. Steam pressure
Right Answers : C

12. What is to be checked on a running Air compressor , during watch.

A. Exhaust temperature
B. Oil coming out of water side
C. Air Bottle Pressure
D. Discharge pressure of liquid
Right Answers : C

13. Watch keeping on Motors & Pumps. .... Mark the incorrect one
A. Temperature of the motor should be felt by back side of palm
B. Current drawn should be in the range
C. There should be abnormal noise and vibration in the pump
D. Gland area should be checked for any leakages
Right Answers : C

14. Which is NOT a means of Internal Communication system

A. Hawse Pipe
B. Walike Talkie
 C. Public Address sytem
D. Sound Powered Telephone
Right Answers : A

Exam Title : Chapter MEK 20

1. Identify the picture given below

A. Electric drill machine

B. External Cir-clip pliers
C. Phillips Screw Driver
D. High leverage combination Pliers
Right Answers : C

2. What is the name of the following tool?

A. philips
B. screw driver
C. studdy
D. electrical tester
Right Answers : D

3. Identify the picture given below

A. Screw Driver
B. External Cir-clip pliers
C. High leverage combination Pliers
D. Electric drill machine
Right Answers : C

4. Identify the picture given below

 A. Soft Hammer
B. Phillips Screw Driver
C. Phillips Screw Driver
D. Electric tester
Right Answers : A

5. Identify the picture given below

A. High leverage combination Pliers

B. Electric drill machine
C. External Cir-clip pliers
D. Phillips Screw Driver
Right Answers : B

6. Identify the picture given below

A. High leverage combination Pliers

B. External Cir-clip pliers
C. Electric drill machine
D. Screw Driver
Right Answers : B

7. Which Instrument is used for testing Insulation

A. Driver
B. Megger
C. Drager
D. Jagger
Right Answers : B

8. Before starting maintenance on any equipment, following precautions to be taken...Mark

the incorrect one
A. Remove the safety guards
B. Put a warning notice on the Mains switch
C. Switch on the main supply
D. Switch off the machine
Right Answers : C

9. Before re-starting a machine, following precautions to be taken...Mark the incorrect one

A. Check that no tools have been left on or near the machine
B. Replace the safety guard after starting the machine
C. Restore the power supply
D. Remove any warning notices
Right Answers : B

10. Dry full contact body resistance is about ______ ohms at 250V
A. 4000
B. 5000
C. 2000
D. 3000
Right Answers : C

11. What is the minimum value of shock current (AC) which can be fatal
A. 25 mA
B. 35 mA
C. 20 mA
D. 15mA
Right Answers : D