Engineering Drawing 2080 Draft
Engineering Drawing 2080 Draft
INSTITUTE OF ENGINEERING
PULCHOWK CAMPUS
ENGINEERING DRAWING
[TUTORIAL SHEETS]
2080
Page 1 of 21
TABLE OF CONTENTS
Page 2 of 21
ENGINEERING DRAWING
SHEET NO: 1
(TECHNICAL LETTERING)
1. Draw the following patterns shown in Figure 1 using T-square and set-square or mini-drafter.
Figure 1.1
2. Dimension the following figures. Size may be obtained by measuring the drawing or assume any
suitable dimension.
Page 3 of 21
ENGINEERING DRAWING
SHEET NO: 1
(TECHNICAL LETTERING)
4. Draw the title block as per the given dimensions and complete it.
Page 4 of 21
ENGINEERING DRAWING
SHEET NO: 2
(PLANE GEOMETRICAL CONSTRUCTION)
Figure 2.4
5. Draw two circles with radii 15 mm and 20 mm respectively with their centers lying on a
horizontal line and 60 mm apart. Draw an arc tangent of radius 50 mm including the circle with
radius 15 mm. and outside of the circle with radius 20mm.
6. Draw two circles with radii 20 mm and 30 mm respectively with their centers lying on a
horizontal line and 60 mm apart. Draw internal and external line tangents to the circles.
7. Draw a parabola with axis length of 60 mm and double ordinate of 80 mm.
8. Draw an ellipse with major and minor axes of 80 mm and 60 mm respectively.
9. Draw a hyperbola with the distance across foci of 60 mm and transverse axis distance of 40 mm.
10. Draw the involutes of the plane figures shown in Figure 2.10 below.
Page 5 of 21
ENGINEERING DRAWING
SHEET NO: 2
(PLANE GEOMETRICAL CONSTRUCTION)
11. A circle of 50 mm diameter rolls on a horizontal surface. Draw the locus of a fixed point on the
circumference of the circle for one complete revolution. Name the curve.
12. Draw an Archemedian Spiral for one and half convolutions with pitch equal to 40 mm.
13. Draw helix for having a pitch of 50 mm on a cylinder with the diameter of 40 mm and height of
75 mm and also find helix angle.
Page 6 of 21
ENGINEERING DRAWING
SHEET NO: 3
(DESCRIPTIVE GEOMETRY)
1. Draw the projections of the following points.
(a) Point A 20 mm above the HP and 15 mm in front of the VP.
(b) Point B 25 mm above the HP and 10 mm behind the VP.
(c) Point C 15 mm below the HP and 25 mm behind the VP.
(d) Point D 10 mm below the HP and 15 mm in front of the VP.
(e) Point E in the HP and 15 mm in front of the VP.
(f) Point F 20 mm above the HP and in the VP.
2. Draw the projections of the following straight lines.
(a) Straight line AB 20 mm long parallel to both the VP and HP. and lying 10 mm above the HP
and 15 mm in front of the VP.
(b) Straight line CD 25 mm long perpendicular to the HP and 20 mm in front of the VP with its
lower end 10 mm above the HP.
(c) Straight line EF 30 mm long perpendicular to the VP and 15 mm above the HP and its end
nearer to the VP is 10 mm in front of it.
(d) Straight line GH 25 mm long parallel to the VP and inclined to the HP at 300. One of its ends is
12 mm above the HP and 18 mm in front of the VP.
(e) Straight line IJ 20 mm long parallel to the HP and 15 mm above the HP and inclined at 40 0 to
the VP. Its end nearer to the VP is 10 mm in front of it.
(f) Straight line PQ 25 mm long contained on the HP and perpendicular to the VP with its end
nearer to the VP is 15 mm in front of it.
3. Top view of a straight line 50 mm long measures 40 mm. The line is on the VP with its lower end
12 mm above the HP. Draw its projections and determine its inclination with the HP.
4. A square ABCD of 20 mm side is parallel to the VP and 15 mm in front of it. Draw its projections
when its edge nearer to the HP is parallel to it and 10 mm above it.
5. A square ABCD of 25 mm side is parallel to the HP and 18 mm above it. Draw its projections
when its edge nearer to the VP is parallel to the VP and 12 mm in front of it.
6. A regular hexagon ABCDEF of side 20 mm is parallel to the HP and 15 mm above it. Draw its
projections when its corner A nearer to the VP is 16 mm in front of the VP and edge AB is inclined
at 390 to the VP.
7. A rectangle ABCD of 60 mm 40 mm is perpendicular to the HP and inclined to the VP at 410.
It is resting on its longer edge on the HP. Draw its projections when its edge nearer to the VP is
parallel to the VP and 16 mm in front of it.
Page 7 of 21
ENGINEERING DRAWING
SHEET NO: 3
(DESCRIPTIVE GEOMETRY)
8. A regular hexagon ABCDEF of 25 mm side rests on one of its edges on the HP. Its plane is
perpendicular to the VP and inclined to the HP at 300. Draw its projections when its corner nearer
to the VP is 15 mm in front of it.
9. A circle of 40 mm diameter is held in such a way that it is perpendicular to the HP and inclined to
the VP at 440. Draw its projections when a point on its circumference is nearer to the VP is 25 mm
above the HP and 10 mm in front of the VP.
10. Top view and front view of a line MN 60 mm long measures 50 mm and 40 mm respectively. One
of its ends is 15 mm above the HP and 10 mm in front of the VP. Draw its projections and determine
its true inclination with the VP and HP.
11. Orthographic projection of a line is given in Figure 3.11. Determine its true length and inclinations
with the HP and VP using,
(a) Revolution method and
(b) Auxiliary view method.
14. Determine the true shape of the triangular plane ABC shown in Figure 3.14 and its inclination
with the HP. Also draw its true shape.
15. Orthographic projections of a plane EFG and a line JK are given in Figure 3.15. Draw the front
and top views of the piercing point and show the visibility of the line. Also determine the true angle
between the line and the plane.
16. Determine the true angle between the given planes ABC and BCD shown in Figure 3.16.
Page 9 of 21
ENGINEERING DRAWING
SHEET NO: 4
(ORTHOGRAPHIC PROJECTIONS)
1. Draw orthographic views of the given objects.
Figure 4.1 a (first angle projection) Figure 4.1 b (first angle projection)
Figure 4.1 c (third angle projection) Figure 4.1 d (third angle projection)
Figure 4.1 e (third angle projection) Figure 4.1 f (third angle projection)
Page 10 of 21
ENGINEERING DRAWING
SHEET NO: 5
(ORTHOGRAPHIC SECTIONAL and AUXULIARY VIEWS)
1. Draw the orthographic views of the objects given below with full sectional front view.
2. Draw the orthographic views of the objects given below with full sectional side view.
Figure 5.2 a (third angle projection) Figure 5.2 b (third angle projection)
3. Draw the orthographic views of the objects given below with full sectional top view.
Page 11 of 21
Figure 5.3 a (third angle projection) Figure 5.3 b (third angle projection)
4. Draw the orthographic views of the objects shown in figures below with half sectional front view
and half sectional side view.
Figure 5.4 b
Figure 5.4 a
5. Draw the front view, the top view, and the normal view of the inclined surfaces for the object
given below.
Make a complete orthographic drawing of a geometrical solid cut by a plane/planes. Find the true
shape of the section/sections. Construct the development of the surface of the solid.
Figure 6 d Figure 6 e
Page 13 of 21
ENGINEERING DRAWING
SHEET NO: 7
(INTERSECTION OF SOLIDS)
Draw the given views of assigned form and complete the intersection curve.
Figure 7 a Figure 7 b
Figure 7 c Figure 7 d
Page 14 of 21
ENGINEERING DRAWING
SHEET NO: 7
(INTERSECTION OF SOLIDS)
Figure 7 e Figure 7 f
Figure 7 g
Page 15 of 21
ENGINEERING DRAWING
SHEET NO: 8
(ISOMETRIC DRAWING)
1. Draw the isometric drawing from the given orthographic views in figures.
10
40
10
30
20
45°
45°
45
35
20
10
10
80
Figure 8.1 c
Figure 8.1 d
Figure 8.1 f
Figure 8.1 e
Page 16 of 21
ENGINEERING DRAWING
SHEET NO: 8
(ISOMETRIC DRAWING)
2. Draw the isometric drawing in section from the given sectional views in figure below.
30
30
22
9
8
34 50
22 70
SQ 50
0
2
30
2 10
Page 17 of 21
ENGINEERING DRAWING
SHEET NO: 9
(OBLIQUE DRAWING AND PERSPECTIVE PROJECTION)
1. Draw an oblique drawing of the object with given orthographic views.
Figure 9.1 e
Page 18 of 21
ENGINEERING DRAWING
SHEET NO: 9
(OBLIQUE DRAWING AND PERSPECTIVE PROJECTION)
2. Draw the parallel perspective projection (Figure 9.2 a) and the angular perspective projection
(Figure 9.2 b) from the given orthographic views.
Figure 9.2 a
Figure 9.2 b
3. A square prism of side base 25 mm and height 30 mm rests with its base on the ground and one of
the rectangular faces inclined at 300 to the picture plane. The nearest vertical edge touches the PP.
The station point is 40 mm in front of the PP, 50 mm above the ground and opposite to the nearest
vertical edge that touches the PP. Draw the perspective view of the prism.
4. Draw the perspective view of a square pyramid of base 30 mm (side) and height of apex 45 mm.
The nearest edge of the base is parallel to and 20 mm behind the picture plane. The station point is
situated at a distance of 70 mm in front of the PP and 40 mm to the right of the axis of the pyramid
and 60 mm above the ground.
Page 19 of 21
ENGINEERING DRAWING
SHEET NO: 10
(SECTIONAL VIEWS)
2. Draw full sectional front view from the given views in Figure 10.2.
3. Draw offset sectional view at A-A from the given views in Figure 10.3.
4. Draw auxiliary sectional view at A-A from the given views in Figure 10.4.
5. Draw sectional front view and top view of the objects shown in Figure 10.5. Use convention for the
radially arranged holes, ribs and spokes.
Page 20 of 21
ENGINEERING DRAWING
SHEET NO: 10
(SECTIONAL VIEWS)
Figure 10.5
Figure 10.4
Page 21 of 21