Engineering Course

•
JMC v1
•
September 2017
 Engineering Course
•
JMC v1
•
September 2017
 Introduction

25/01/21 3
Objectives

This section covers:

•
Use and Purpose
•
Desk Kit
•
Hardware
•
Order Codes
•
Default Settings
•
Licencing Requirements
Use and Purpose

Multiple
Gateways

•
Traditionally, multiple Gateways were used to integrate different Systems
•
TONN8 is designed to be an easy Interface for Integration between various Protocols
•
Drivers are used to translate between the TONN and the respective Protocols
Use and Purpose

•
Each Driver communicates in its own Protocol to the third Party Devices and is then translated or
‘normalised’ to Niagara4 inside the TONN
•
The normalised Data in Niagara4 can be linked to any other normalised Components and then translated
into another Protocol via the relevant Driver and sent to another Network
 Desk Kit
Offices
Floors & Lighting Controller Modbus Meters
Sports Complex
Plant Controller

Modbus RS485
Ethernet
TCP/IP
LON FTT

Window
Thermokon Contact
Display

•
The TONN on the Desk will be used to integrate the Modbus Meters and Thermokon LON Display into the
Trend Network
TONN8 Hardware – SD Card

Insert SD Card before

connecting the Power Supply

•
SD Card is not Factory fitted, but supplied inside the TONN’s Box
•
SD card must be mounted before TONN is powered up
•
Insert SD Card by sliding down the Connector next to the WiFi Aerial
TONN8 Hardware – WiFi Antenna

•
WiFi Mode must be configured correctly
•
OFF – Default Setting, Button in Center means WiFi disabled
•
ACC – TONN becomes WiFi Access Point for up to 20 Clients
•
CLT – TONN connects to Network via and existing Router or Access Point
TONN8 Hardware - Power Supply

Polarity Independent

TONN must be earthed at

separate Earth Point,
Transformer Secondary must
not be tied to Ground

•
24VAC – Dedicated Class 2 24V Transformer rated 24VA with neither Side of the Secondary tied to Ground
•
24VDC – Class 2 or LPS24VDC Power Supply with neither Leg tied to Ground
•
TONN must be earthed separately at dedicated Earth Connector
 TONN8 Hardware – RS485 Connections

Screen
Screen
COM1 COM2

A+
A+

A-
A-
Shielded twisted Pair 12-22
AWG Cable should be used,
wiring + to +, - to – and Screen
to Screen

2 RS485 Ports capable of up to 115,200 Baud with 3 Position Biasing Switches:

•
BIA – 2.7K Ω Bias with no Termination Resistor – Factory Default Setting
•
END – 562Ω Bias Resistors and 150Ω Termination Resistor
•
MID – 47.5KΩ Resistors with no Termination Resistor
TONN8 Hardware – Ethernet Connections

TONN is not compatible with

Power over Ethernet Networks
If connected to a POE Network
the Unit may stop functioning

•
PRI – Primary Ethernet Port, if only one Ethernet Connection is needed, the Primary Port must be used
•
SEC – Secondary Ethernet Port, must not be used if only one Ethernet Connection is available
•
Primary and Secondary Ethernet Ports are NON-ROUTING and must be connected to different Subnets
TONN8 Hardware – Expansion Modules

•
RS232, RS485 and LON Expansion Modules can be fitted
•
Expansion Modules connect to the Connector on the right of the TONN
•
A Maximum of 4 Expansion Modules can be fitted to a TONN
TONN8 Hardware – Expansion Modules

6
1
5
3

•
RS232 – Serial Expansion Module with 1 x RS232 Port
•
LON – LON Expansion Module with 1 x LonWorks FTT-10A Port
•
RS485 - Serial Expansion Module with 2 x RS485 Ports
TONN8 Hardware – Expansion Modules

COM1 COM2 COM3 LON1 COM5

COM4

•
Expansion Modules plug into the TONN8
•
COM Ports are assigned in physical Order, ie nearest Module to TONN8 starts at the lowest
available COM Port Number
•
A Maximum of 4 Expansion Modules can be fitted to a TONN8
TONN8 Controller Order Codes
Order Code Description
TONN-8100-24 TONN8 with 100 Proxy Point Licence, 1yr SW Agreement

TONN-8250-24 TONN8 with 250 Proxy Point Licence, 1yr SW Agreement

TONN-8500-24 TONN8 with 500 Proxy Point Licence, 1yr SW Agreement

TONN-81250-24 TONN8 with 1250 Proxy Point Licence, 1yr SW Agreement

TONN-85000-24 TONN8 with 5000 Proxy Point Licence, 1yr SW Agreement

TONN-810000-24 TONN8 with 10000 Proxy Point Licence, 1yr SW Agreement

TONN-W02-8100-24 TONN8 with WiFi & 100 Proxy Point Licence, 1yr SW Agreement

TONN-W02-8250-24 TONN8 with WiFi & 250 Proxy Point Licence, 1yr SW Agreement

TONN-W02-8500-24 TONN8 with WiFi & 500 Proxy Point Licence, 1yr SW Agreement

TONN-W02-81250-24 TONN8 with WiFi & 1250 Proxy Point Licence, 1yr SW Agreement

TONN-W02-85000-24 TONN8 with WiFi & 5000 Proxy Point Licence, 1yr SW Agreement

TONN-W02-810000-24 TONN8 with WiFi & 10000 Proxy Point Licence, 1yr SW Agreement
Expansion Module, Upgrade & Driver Order Codes

Order Code Description

HON-NXEM-LON LON Expansion Module Single Port
HON-NXEM-2x485 R485S Expansion Module Dual Port
HON-NXEM-232 RS232 Expansion Module Single Port
TONN8-DR-N4-TREND Trend Driver for N4 TCP/IP and Serial
TONN8-DR-N4-FIDELIO Fidelio Driver for N4 TONN8
TONN8-DR-N4-SMS SMS Driver for N4 TONN8
TONN-8-UP-500 TONN8 Upgrade for an additional 500 Proxy Points
TONN-8-UP-1250 TONN8 Upgrade for an additional 1250 Proxy Points
TONN-8-UP-2500 TONN8 Upgrade for an additional 2500 Proxy Points
TONN-8-AX Enables TONN8 to run Niagara AX
Software Update Agreement Order Codes

Order Code Description

TONN-8250-SA-1YR, 3YR or 5YR 1, 3 or 5 Year SW Update Agreement
for a 100-499 Point TONN8 respectively
TONN-8500-SA-1YR, 3YR or 5YR 1, 3 or 5 Year SW Update Agreement
for a 500-1240 Point TONN8 respectively
TONN-81250-SA-1YR, 3YR or 5YR 1, 3 or 5 Year SW Update Agreement
for a 1250-4999 Point TONN8 respectively
TONN-85000-SA-1YR, 3YR or 5YR 1, 3 or 5 Year SW Update Agreement
for a 5000-9999 Point TONN8 respectively
TONN-810000-SA-1YR, 3YR or 5YR 1, 3 or 3 Year SW Update Agreement for a
10000+ Point TONN8 respectively
Default Settings

•
TONN8 is engineered using IQVision
•
The Factory Default IP Address for EVERY TONN8 is 192.168.1.140 on Subnet Mask 255.255.255.0
Licencing - Automatic

•
If the TONN8 is connected to the Internet, it will connect to the Tridium Server and find its Licence
automatically
Licencing - Manual

Sales Order No
123456

•
To manually licence the TONN8, Technical Support must be contacted with the Qnx Code printed
on the case of the SD Card, the Serial Number under the TONN’s lid and the Trend Order Number
•
Tech Support will then email 2 zip Files – one containing the Licence and the other containing the
Certificate
Conclusion

This section covered:

•
Use and Purpose
•
Desk Kit
•
Hardware
•
Order Codes
•
Default Settings
•
Licencing Requirements
Quick Quiz

Question: How does the TONN communicate with third party devices?

A Via Applets

B Via Drivers

Via Gateways
C

D All of the above

Quick Quiz

Question: What happens to third party data inside the TONN?

A It is standardised

B It is niagarised

C It is normalised

D It is tridiumised
Quick Quiz

Question: What information is required to obtain a TONN licence if it is not

connected to the internet?

A Qnx Code, Serial Number and Tridium Order Number

B Win Code, Serial Number and Trend Order Number

C Win Code, Serial Number and Tridium Order Number

D Qnx Code, Serial Number and Trend Order Number

Quick Quiz

Question: How many Expansion Modules can be fitted to a TONN8?

A 5

B 4

C 3

D There is no limit