Costuming:CC - CW-Wolffe Desert Season 6

Clone Commander Wolffe (Desert Gear)

Model CC-41255, Photo by Sarah Pugliaresi

Visit the Gallery for this Costume for more models and parts views.

Description: Clone Commander Wolffe (Desert Gear) Prefix: CC Detachment: Clone Trooper Detachment Context: The Clone Wars, Season 6 CC-3636, nicknamed Wolffe, was a clone commander who fought during the Clone Wars, serving under the command of Jedi General Plo Koon as leader of a clone squad named Wolfpack, a division of the 104th Battalion. Assisting Plo Koon on his missions Commander Wolffe has to work in all possible surroundings. While searching for the lost lightsaber of Jedi Master Sifo Dyas Wolffe has to get through the sandstorms of a desert planet. Equipped with his desert gear he and the Wolfpack were able to survive this unfriendly environment.

For 501st membership only the requirements in black need to be met. In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume. Special Notes: • The “Animated” armor design, seen in 2008 The Clone Wars Cartoon Series, differs from the “Realistic” armor design used to create characters from the theatrical films, video games, and graphic novels. See this thread at 501stclonetroopers.com for the differences between the sculpts. (This may require an additional forum account.) • Armor parts shall be made from fiberglass, ABS (Acrylonitrile Butadiene Styrene), HIPS (High Impact Polystyrene), or a similar rigid material. This includes vacuum formed plastics as well as properly finished and smoothed 3D printed armor forms. See this thread at 501stclonetroopers.com for examples of acceptable and unacceptable levels of 3D print finishing. • All numerical measurements given in CTD CRLs are approximate. Measurements should be followed as closely as possible while not affecting the proportionality of costume details. Proportionality should take precedence over exact measurements.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type. This document is not intended to be a detailed how-to on costume construction; rather a visual guide to be used for 501st costume approval. Details on construction may be found on the respective costume detachment web forum. GMLs uncertain about an aspect of submitted costume shall post questions in the appropriate DL/GML peer review section of the Legion forum. Measurements given in this document are intended to be approximate and generalized; not criteria for approval. Requirements for all 501st costumes are proportional to the wearer in scale, fit and size. Text descriptions are only one part of the guideline. GMLs and costumers must consider both text and pictures (CRL and Reference) when reviewing the costume.

Required Costume Components

The following costume components are present and appear as described below.

Helmet Desert clone animated style helmet. Helmet dome is similar to the shape of a Snowtrooper. Face shield includes a nose ridge about two inches (five centimeters) wide extending from brow down to frown in a point. Two raised black aerators are located at the sides of the bottom of the chin area. The raised chin detail is black and trapezoidal in shape. Face shield is white on the cheeks and dark-grey along the jawline. The center nose ridge is dark grey Along the lower cheek area is Wolffe stylized fur detail above which is a rectangular cutout with black mesh or fabric backing. Above the chin detail are Wolffe stylized teeth details. There is a red triangle above the brow with 3 yellow 'kill' stripes on both sides. Dark-grey RF stalk mounted on the outside of the ear. There is a raised square over each ear cap area of the dome measuring approximately one and three-quarters inches (4.5 centimeters) on each side. There is a raised trapezoid measuring approximately one inch (two centimeters) high, a half an inch (one centimeter) at the base, and a quarter of an inch at the top over each of the temples along the brow of the dome. Helmet is weathered with shades of grey.

---

	Neckseal The neck seal has two layers: the outer layer which is the same dark-grey as the jumpsuit and the underlayer which is white. The white underlayer extends approximately one and a half inches (four centimeters) above the dark-grey. Neck seal is weathered with shades of grey.

---

	Jumpsuit The jumpsuit fabric is dark-grey heavy cotton or cotton-like. The legs are quilted with vertically oriented squares. The arms are quilted with rhomboidal sections vertically oriented down the length of the arm. The midsection is quilted with a center panel forming a large “X”. The rest of the midsection is quilted with vertically oriented rectangles.

---

Shoulder Armor Desert Wolffe animated style shoulder armor. The left shoulder is painted matte dark-grey with Plo Koon’s sunburst. Left shoulder also includes a mounted antenna array. Right shoulder is painted matte dark-grey with the wolf head emblem. Two semi oval lines on the outside edges of each shoulder painted in matte white. Seven raised trapezoid shapes around the edges of each shoulder painted matte white. Shoulders are tear drop in shape with all rounded edges. Shoulder armor is not symmetrical. The shoulders slightly curve back at the bottom. Armor is weathered with shades of grey.

---

Forearm Armor Desert Wolffe animated style forearm armor. Armor is painted matte white. Armor is a rigid leather or leather-like material. Dark-grey markings are painted as shown. Armor is rounded near elbow. There is a second layer of material underneath the primary layer. also painted white, extending out approximately a half an inch (1.25 centimeters). The raised dark-grey detail covers only the front part of the forearm. Two black square details on the bottom of each forearm near the wrist. Armor is weathered with shades of grey.

---

	Hand Plates Desert Wolffe animated style handplates. Armor is painted matte dark-grey with a matte white border a half inch (1.25 centimeters) wide. Armor is weathered with shades of dark-grey.

---

	Gloves Desert Wolffe animated style gloves. White gloves over the wrist made of leather, nylon, cotton or other low pile fabrics. Gloves cover any exposed skin. Gloves do not show any labels or logos when the armor is worn. Gloves are weathered with shades of grey.

---

Chest Armor Upper raised pectoral region is continuous without center cutout, similar to animated style phase 2 chest armor. Armor is painted matte or satin white with dark-grey detail. Top section of the chest has a matte dark-grey area as shown. Lower portion of the chest has a squared notch. Chest and back plate match together at the sides and shoulders with no open gap. Butted seam lines are permitted if required. Shoulder straps fit into the tops of the chest and back. Two Pouches mounted on chest as shown, measuring approximately 5 x 3.5 x 1 inches (12.5 x 9 x 2.5 centimeters) with front detail as shown . Painted 'desert' brown. Leather or leather-like straps extend from behind pouches to the back of armor, approximately three inches (7.5 centimeters) wide. Armor is weathered with shades of grey.

---

	Back Armor Armor is painted matte white. Top section of the back armor has a dark-grey area extending up to the detail plate as shown. Chest and back plate match together at the sides and shoulders with no open gap. Butted seam lines are permitted if required. Shoulder straps fit into the tops of the chest and back. Armor is weathered with shades of grey.

---

Backpack Desert Wolffe animated style backpack. Backpack is painted matte white. Pack has a large inset rectangle on the left side of the main face, including the following details: Upper left cover has two vertical raised rectangle details, with the left one painted red and right one painted blue. Lower left has horizontal raised rectangle with rounded edges. Right side has raised rectangular detail with washer-style detail on the top and a thin horizontal bar in the middle. Upper sides of pack feature two raised vertical rectangle details. Lower ides of pack feature a raised circle detail with a raised line crossing through the center of it. Pack features a hose coming from the top middle and attaching to a pipe that lays on the right side of the front face of the pack. Backpack is weathered with shades of grey.

---

Belt Desert Wolffe animated style belt. Belt and boxes are painted matte white Two cylinder canisters are present on the front of the belt. Both are painted matte white and details are in grey. White trapezoid shaped soft cod, extending down to mid-thigh, made of a leather or leather-like material Belt has raised details as shown: Two oblique, two small rectangles on the front of the belt and an inverted “V” design in the center. Four small rectangles on rear of belt. All are positioned in a symmetrically Side boxes are painted matte white: two large and one small box on each side over the pouches and back section of the belt. Belt is weathered with shades of grey.

---

	Duster Desert Wolffe animated style duster. The duster is made of black heavy canvas, canvas-like or suede material with white detail. Corners of the duster are rounded. The duster extends down to the mid-calf. Duster has white “Wolf teeth” pattern at the base matching references. Duster is weathered with shades of grey.

---

	Holsters Phase 2 animated style holsters. Holsters are painted matte or satin white. Holsters may connect to the belt via straps or directly to the kama with no visible attachment. Holster is weathered with shades of grey.

---

Lower Leg Armor Desert Wolffe animated style lower leg armor. Armor is painted matte white. The first, second, fourth and fifth segments are approximately two and a half inches (6.5 centimeters) tall. The third segment is 4 inches (10 centimeters) tall. Each section is divided by a recessed gap of approximately half an inch (1.25 centimeters) and is painted grey. The knee armor is integrated with the lower leg with rounded corners at the top. The outer seam of the shin is seamless. A clam-shell opening on the inner or back seam is acceptable. The front of the bottom section is cut out at the ankle to sit over the top of the boots and cover the sides of the ankle. Armor is weathered with shades of grey.

---

	Boots Desert Wolffe animated style boots. The shoes are matte white in color. The edge of the sole is flat. Raised detail located on the toe and includes a center strip running from the toe to the ankle. Boots are weathered with shades of grey.

---

Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.

	DC-17 Hand Blaster (animated style) Manufactured by BlasTech Industries, DC-17 pistols are designed for use as secondary weapons. Because they are widely recognized for their high stopping power and firing rate, many battlefield officers use them as primarily combat weapons. This is the animated variant of the DC-17 blaster. The number of pistols carried is dependent on the number of holsters.

---

• This CRL is available as a PDF

This document and all of the images within were created by and are the property of the 501st Legion. Other media owned by Lucasfilm Ltd and Disney are used under authorization. All other uses are prohibited. The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it follows generally accepted ground rules for Star Wars fan groups. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. Copyright and Trademark Lucasfilm Ltd. All rights reserved. Used under authorization.