Costuming:CC - Kamino Security Phase 2

From 501st Legion Databank
crlblackhd.gif
 
Kamino Security Commander
Clone CC Kamino Security Full Body.jpg
Model CC-9389, Photo by Zach Winnermark
 
Visit the Gallery for this Costume for more models and parts views.


Clone-Trooper-Detachment.png

Description: Kamino Security Commander
Prefix: CC
Detachment: Clone Trooper Detachment
Context: The Clone Wars Season 6

A clone trooper served on Kamino under Jedi Master Shaak Ti during the Clone Wars. He was tasked with tracking down Fives, who had gone rogue shortly after learning of Inhibitor chips placed within the minds of all clone troopers.


For 501st membership only the requirements in black need to be met.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

Special Notes:
• The “Animated” armor design, seen in 2008 The Clone Wars Cartoon Series, differs from the “Realistic” armor design used to create characters from the theatrical films, video games, and graphic novels. See this thread at 501stclonetroopers.com for the differences between the sculpts. (This may require an additional forum account.)
• Armor parts shall be made from fiberglass, ABS (Acrylonitrile Butadiene Styrene), HIPS (High Impact Polystyrene), or a similar rigid material. This includes vacuum formed plastics as well as properly finished and smoothed 3D printed armor forms. See this thread at 501stclonetroopers.com for examples of acceptable and unacceptable levels of 3D print finishing.
• All numerical measurements given in CTD CRLs are approximate. Measurements should be followed as closely as possible while not affecting the proportionality of costume details. Proportionality should take precedence over exact measurements.


This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.


  • This document is not intended to be a detailed how-to on costume construction; rather a visual guide to be used for 501st costume approval. Details on construction may be found on the respective costume detachment web forum.
  • GMLs uncertain about an aspect of submitted costume shall post questions in the appropriate DL/GML peer review section of the Legion forum.
  • Measurements given in this document are intended to be approximate and generalized; not criteria for approval.
  • Requirements for all 501st costumes are proportional to the wearer in scale, fit and size.
  • Text descriptions are only one part of the guideline. GMLs and costumers must consider both text and pictures (CRL and Reference) when reviewing the costume.


Required Costume Components

The following costume components are present and appear as described below.


Clone CC Kamino Security Helmet.jpg Helmet
  • Phase II animated style helmet with Commander attachments.
    • Movie style helmets are not combined with animated armor.
  • Armor is painted mattte white.
  • Mohawk on dome with a narrow ridge along each side.
    • Mohawk is painted matte dark grey.
  • A phase II animated visor sits on the brow and extends to the back of each ear.
    • Visor is painted dark grey with white details.
  • Bullet shape lamp is located on the left hand side of the dome, just above the visor.
    • Lamp is painted dark grey.
  • Black eye lens extends down to the nose.
  • Dark grey frown with (3) black teeth on either side.
    • Teeth may be cut out and backed with black mesh or painted.
  • (2) aerators in the front.
    • Aerators are black with a grey or white center detail.
  • (6) vents on each side of helmet.
    • Vents may be painted black or grey, or cut out and filled with black mesh.
  • Center of lower jaw is painted matte dark grey.
  • There are (12) dark grey stripes on the front of each tube, they are evenly spaced starting at the 12 o’clock position and finishing at the 5 o’clock position for the left and 7 o’clock position for the right.
  • (3) Ear caps are dark grey on each ear.
  • The indented cheek area is painted matte dark grey and the grey extends around the ear and to the rear recessed areas, finishing at the rear raised section.
  • Matte white trapezoid on helmet band behind antenna on right side and similar location on left side of helmet.
  • There is an antenna behind the right ear.
    • Base of antenna starts at the recessed area and finishes approximately at the top of the ear cap.
    • The antenna then extends from the base.
  • Antenna is painted dark grey or black.
  • Rear center of the helmet is painted matte white.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.




TC animated neckseal.jpg Neck Seal
  • Neck seal is black in color with no ribbing.
  • No logos or labels are visible.


OPTIONAL Level two certification (if applicable):
  • Neck seal closes in the front via two small black snaps.
  • A black balaclava is worn with the neckseal.




TK anh stunt undersuit.jpeg Under Suit
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.



Clone CC Kamino Security Shoulder Armor.jpg Shoulder Armor
  • Phase II animated style shoulder armor.
  • Shoulders are painted matte white with dark grey details.
  • Both shoulders have the appropriate "C" in aurebesh emblem.
  • Shoulders are tear drop in shape with all rounded edges.
  • Shoulder armor is not symmetrical.
  • The shoulders slightly curve back at the bottom.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Biceps.jpg Upper Arm Armor
  • Phase II animated style upper arm armor.
  • Armor is cylindrical with no detail/sculptural features.
  • Armor is painted matte white.
  • Arms have (2) dark grey stripes around the entire bicep.
    • Approximately 1/2 inch dark grey stripes, spaced approximately 1/2 inch apart.
  • The top of the upper stripe is approximately half way down the bicep.
  • The bottom stripe is approximately 1/4” above the bottom of the bicep.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Forearms.jpg Forearm Armor
  • Phase II animated style forearm armor.
  • Armor is painted matte white
  • Right forearm has a compad with (8) small buttons, (1) large main button, and (1) slightly small rectangular button.
    • Compad is painted white
  • Armor is seamless on the outside edge.
    • Due to the shape of the armor, a butted seam is acceptable on the inside if required.
  • Elbow armor does not extend past the elbow.
  • Armor is weathered with shades of grey.


OPTIONAL Level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.



Clone CC Kamino Security Handplates.jpg Hand Plates
  • Phase II animated style hand plates.
  • Armor is painted matte white.
  • Hand plates are mirror images of each other.
  • Armor is weathered with shades of grey.




Generic-black-gloves.jpg Gloves
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.



Clone CC Kamino Security Chest Armor.jpg Chest Armor
  • Phase II animated style chest armor.
  • Armor is painted matte white
  • Upper portion of the chest is painted matte dark grey
  • Lower portion of the chest has an angular notch for the abdomen armor to fit into.
  • Chest and Back armor match together at the sides and shoulders with no open gap.
    • A seam line is present.
  • Dark grey shoulder straps are placed underneath the Chest to connect to the Back.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Back Armor.jpg Back Armor
  • Phase II animated style back armor.
  • Armor is painted matte white
  • Rear tank has detailed area that contains (4) circles.
  • Under the circles, at the left side of the back, there are two parallel blocks.
    • To the right of the back there are (3) parallel blocks.
    • All details painted dark grey.
  • Dark grey shoulder straps are placed underneath the Back to connect to the Chest.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Abdomen.jpg Abdomen Armor
  • Phase II animated style abdomen armor.
  • Armor is painted matte white
  • Top edge of the armor is angled to match the chest.
  • The abdomen armor protrudes out in the middle to match the chest.
  • (4) inset lines divide the abdomen armor into segments.
  • A butted seam between the Abdomen and Kidney armor is acceptable.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Kidney.jpg Kidney Armor
  • Phase II animated style kidney armor.
  • Armor is painted matte or satin white.
  • A butted seam between Kidney and Abdomen is acceptable.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Cod Piece.jpg Codpiece and Belt front
  • Phase II animated style codpiece and belt front armor.
  • Armor is painted matte white
  • Belt is approximately 3” tall and divided into 1.75” wide segments.
  • The front segments have a key/slot detail.
  • Belt boxes are mounted at the hips.
  • Butted seams are permitted at the connection if required.
  • Belt and belt boxes are painted matte dark grey
  • Codpiece and Posterior armor connect at the hips with no open gap.
  • A seam line is present.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Posterior.jpg Posterior Armor, Belt rear and Detonator
  • Phase II animated style posterior armor, belt and detonator.
  • Armor is painted matte white.
  • Belt is approximately 3” tall and divided into 1.75” wide segments.
  • Belt boxes are mounted at the hips.
    • Butted seams are permitted at the connection if required.
  • Belt and belt boxes are painted matte dark grey.
  • Detonator is centered on the back of belt.
    • Detonator has no control buttons.
  • Detonator is painted matte white.
    • The detonator has (2) lines set in approx 1/2" - 5/8" from the edges.
      • Lines may be recessed or painted on.
  • The inside of the detonator end caps are painted dark grey.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Kama.jpg Kama
  • Phase II animated style kama.
  • The Kama is made of black leather, leather like material, or heavy canvas.
  • Kama has primer dark grey border trim.
  • The front edges of the Kama line up with the outside edges of the front two panels of the belt.
  • The back of the Kama is split all the way up to the belt.
  • The bottom edges of the kama are rounded.
  • The kama extends to the middle of the knee.



Clone CC Kamino Security Holsters.jpg Holsters
  • Phase II animated style holsters.
  • Holsters are painted matte or satin white.
  • Holsters connect to the belt via straps.
    • Straps are painted matte or satin white.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Belt Boxes.jpg Belt Boxes
  • Phase II animated style belt boxes.
  • Two rectangular boxes with one mounted on each side of the belt.
  • Boxes are painted matte dark grey.
    • The top of the box is tapered outward.
    • There is an inset detail near the top of each box.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Thighs.jpg Thigh Armor
  • Phase II animated style thigh armor.
  • Armor is painted matte white
  • Front thigh armor has a flat triangular area near the knee with a notch cut out for the knee armor.
  • From the top of the triangle a ridge line travels up the front of the thigh to the top edge.
  • Armour is seamless.
  • No visible traces of how the armor was assembled are shown.
  • Rear of the thigh has an indentation.
  • Armor is weathered with shades of grey.



Clone CC Kamino Security Lowerlegs.jpg Lower Leg Armor
  • Phase II animated style lower leg armor.
  • Armor is painted matte dark grey
  • Knee armor is painted matte white
  • The armor has a flat center triangle below the knee plate, with the single point facing downward.
  • The calf detail of the armor has a ridge wrapping around the back of the leg.
  • Back of the lower legs have an indentation just under the calf that extends down to the ankle.
  • The outside of the calf is closed.
  • Calf may have an access area on the inside of the leg.
  • Dark grey areas are weathered with various scuff marks and fading.
    • Scuff marks expose the underlaying white paint.
  • Armor is weathered with shades of grey.


OPTIONAL Level two certification (if applicable):
  • Calves are seamless with a trap door access through the indent in the rear of the lower leg.



Clone CC Kamino Security Boots.jpg Boots
  • Phase II animated style boots.
  • Dark grey, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area.
  • Boots are lace-less with flat soles.
  • Boots have a center strip extending from the toe to the ankle.
  • A strap across the top of the foot, with (2) flat white discs on either side of the foot, terminating the strap.
  • Soles are white.


OPTIONAL Level two certification (if applicable):
  • Boots have accurate notched sole.



Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.



CW animated dc17 pistol.jpg DC-17 Hand Blaster (animated style)

Manufactured by BlasTech Industries, DC-17 pistols are designed for use as secondary weapons. Because they are widely recognized for their high stopping power and firing rate, many battlefield officers use them as primarily combat weapons.

  • This is the animated variant of the DC-17 blaster.
  • The number of pistols carried is dependent on the number of holsters.






This document and all of the images within were created by and are the property of the 501st Legion. Other media owned by Lucasfilm Ltd and Disney are used under authorization. All other uses are prohibited. The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it follows generally accepted ground rules for Star Wars fan groups. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. Copyright and Trademark Lucasfilm Ltd. All rights reserved. Used under authorization.

Retrieved from "https://databank.501st.com/mw501/index.php?title=Costuming:CC_-_Kamino_Security_Phase_2&oldid=31710"