|
|
|
| Republic Officer The Clone Wars
|
|
Model ID-99933, Photo by Cedric Grafas
|
|
|
|
Description: Republic Officer—The Clone Wars
Prefix: ID
Detachment: Imperial Officer Corps
Context: Star Wars: The Clone Wars
These officers served the Republic Starfleet during the conflict with The Confederacy of Independent Systems.
|
|
|
|
For 501st membership only the requirements in black need to be met.
The Imperial Officer Corps defines additional, optional levels of costuming excellence. In the page below, requirements for Level 2 “Executor” are listed in blue. Requirements for Level 3 “Imperator” are listed in red.
|
|
This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
- This document is not intended to be a detailed how-to on costume construction; rather a visual guide to be used for 501st costume approval. Details on construction may be found on the respective costume detachment web forum.
- GMLs uncertain about an aspect of submitted costume shall post questions in the appropriate DL/GML peer review section of the Legion forum.
- Measurements given in this document are intended to be approximate and generalized; not criteria for approval.
- Requirements for all 501st costumes are proportional to the wearer in scale, fit and size.
- Text descriptions are only one part of the guideline. GMLs and costumers must consider both text and pictures (CRL and Reference) when reviewing the costume.
|
|
|
|
Tunic
- Olive/grey colored fabric is a medium weight suiting material exactly matching the pants.
- Tunic is double-breasted with a left over right closure on the tapered yoke.
- Yoke comes up across the shoulder to the top shoulder seam.
- The standing collar has square corners with a left over right closure in the center.
- Collar includes a modesty panel.
- The tunic has black piping made of matte satin.
- There are epaulettes on each shoulder.
- Sleeves are long, and without cuffs or buttons.
- Sleeves contain 2 seams, one in front and one in back.
- There are two rank-bands of black satin ribbon on both sleeves.
- Tunic is constructed with no top-stitching (stitches visible on the exterior surface of fabric).
- The back of the tunic has one seam that runs in the center of the tunic from the neck to the bottom.
- There is a vent that runs from belt height to the bottom on the back of the tunic.
|
OPTIONAL Level two certification (if applicable):
•Collar is approximately 1.25" (3.175 cm) to 2.5" (6.35 cm) tall
|
OPTIONAL Level three certification (if applicable):
• Tunic is secured on the right side by snaps or buttons.
• There is no top-stitching visible anywhere.
• A lining is sewn in.
• The shoulder lines are very straight in appearance.
|
|
|
|
Jodhpurs
- Olive/grey fabric is a medium weight suiting material exactly matching the tunic.
- Trousers are riding breeches with semi-stiff flares to the hip/thigh area and tucked into the boots.
- Pockets are acceptable but shall not be visible with the tunic on.
|
|
|
|
Rank Bar
- The rank bar is worn on the left side of the tunic above the piping.
- Rank consists of colored plastic tiles mounted inside a frame-plate.
- The upper and lower frames are divided by a small indentation.
- Three red tiles in the top frame.
- Two blue tiles in the bottom frame.
|
OPTIONAL Level two certification (if applicable):
- Each bar is approximately 1⅛" (28.6 mm) height.
- Length of the upper frame-plate is approximately 2⅓" (6 cm) wide, if double bars are used.
- Length of the lower frame-plate is approximately 1⅝" (4.1 cm) wide.
- Rank tile dimensions are approximately ⅝" (16 mm) width x ⅞" (22 mm) height.
- The mounted tiles are slightly horizontally curved upwards in the middle.
|
|
|
|
Belt
- The belt is constructed from a non-textured leather or a leather-like material and is approximately 2" (51 mm) wide.
•There are no loops on the belt.
•The buckle has rounded corners and constructed from a horizontally brushed metal, or metal looking material.
- Buckle is adorned with a Republic code disk in the center.
•The Code disk is a stepped cone shape appearing to be 2 disks stacked on top of one another.
• The larger disk is 1.4 inch (3.5 cm), the smaller disk is 1 inch (2.5 cm).
|
|
|
|
Boots
- If stretch panels or zippers are present they are to be hidden on inner shaft.
- Boots are bulged wider on both sides of the ankle.
- The upper edge of the shaft is cuffed.
|
OPTIONAL Level two certification (if applicable):
- Boots have no zipper.
- Boots are made of leather.
|
|
|
|
Gloves
- Gloves are made from black leather or leather-like material; gloves can be plain or have 3 stitch lines on the back of the hand.
|
|
|
This document and all of the images within were created by and are the property of the 501st Legion. Other media owned by Lucasfilm Ltd and Disney are used under authorization. All other uses are prohibited. The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it follows generally accepted ground rules for Star Wars fan groups. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. Copyright and Trademark Lucasfilm Ltd. All rights reserved. Used under authorization.
