Costuming:BH DinDjarinS1V1

Din Djarin: Season 1, Version 1

Model Mike Quinones, BH-42011, Photo by Lacy Quinones

{CRLdetinfo|1105|Din Djarin Season 1: Version 1|BH|Star Wars: The Mandalorian, aka “Din Djarin”|A lone Mandalorian who carries out bounties efficiently and without hesitation. Considered one of the best in the Bounty Hunter’s Guild by Greef Karga up until the one bounty that would change his reputation. Armed with his signature Amban Sniper Rifle and blaster, if Din has your bounty puck it is only a matter of when he finds you…}}

For 501st membership, only the requirements in black need to be met. The Bounty Hunters’ Guild defines an additional optional level of costuming excellence. In the page below, requirements for Level 2, referred to as “Infamous”, are listed in blue. These optional requirements are meant for those who strive to meet the highest level of screen accuracy. Please visit the BHG web site for a full description of these standards.

This CRL is a work in progress and is not yet ready to use for any approval!

General Construction Notes All costume elements are painted and weathered to match the specific visual references for this version. All components should closely match the Din Djarin Season 1: Version 1 Color Palette. Color palette is intended for reference in building, and will only be used in exacting measurement by Detachment for Infamous Level approval. A Basic level approval is only required to be similar, not exact. All Armor is constructed from a rigid material such as Metal, Fiberglass, Resin, Sintra, HIPS, PVC, PLA, Vac-formed ABS, or similar, foam armor is not approved. Please Note: All damage must be 100% screen accurate if individual wishes to obtain Infamous (Level 2) approval from Detachment.

---

	Helmet Helmet is a uniform dark chrome in appearance with subtle bronze/brown weathering all over. Heavier weathering appears in cracks and crevices surrounding helmet details. Visor is dark gray. The mandibles taper slightly so that the top of the vertical section of the visor has a wider gap than at the bottom. Bottom of the front mandibles are angled at approximately 45 degrees inwards from the bottom where the cheeks meet. Visor ends middle of slanted section at bottom of mandibles. Front brow has a groove 1/3 from the top, extending from ear cap to ear cap. Helmet has a raised Mohawk detail that extends from the front brow to the top of the Shingles area in the back. Mohawk has a rectangular groove that separates it into equal thirds. Front of Mohawk corners angle from bottom of brow groove to top of brow. The front tip of the Mohawk sits on-top of the front brow. Ear caps are symmetrical to each other. The back of the helmet has an inlaid rectangular section with an embedded and raised frame that houses 6 angled shingle details with each shingle nestled under the shingle detail above it. Each shingle has a rectangular section cut out of the bottom edge.
	OPTIONAL Level two certification (if applicable): Ear caps do not show any visible seams where they meet the helmet’s surface. Upside down U and recessed section just below the upper cap on each ear is visibly darker and does not possess the same luster as the rest of the helmet. Helmet is painted in a way that closely resembles the Alumaluster finish seen on screen.

---

	Chest Armor Chest armor consists of two sections that are one solid piece but appear to be separated. The upper section has two breast plates and a recessed center strip displaying an embossed diamond style detail. The lower section has an abdominal plate that appears to be separated. Armor sections have return edges all around, giving the appearance of thickness and depth. Armor is a medium brown/brown red base (Similar to PMS 483 C) with weathering that appears to expose a metallic base color with light and dark gray around the silver. Center Diamond is silver and light gold/bronze with 6 sides: 4 long with 2 short at the top and bottom. A single rectangular groove runs vertically in the diamond but does not connect to the edges. The chest armor attaches securely to the flak vest without any visible attachment method. Top of the chest armor is worn slightly above the top of the flak vest. The bottom of the lower plate sits even with or slightly above the stitching on the lower edge of the vest. Armor rests approximately at the wearer’s elbow.
	OPTIONAL Level two certification (if applicable): A blaster dent is only present in the upper right breast plate if Option 2 of the Right Shoulder armor is worn. Armor return edges are more significant on the upper chest plates, less on the abdominal plate.

---

Back Armor Back Armor encompasses the mid and upper back areas and is painted in the same color scheme as the Chest Armor. Armor curves to fit the wearer’s back and ends slightly above the bottom seam of the Flak Vest. Armor has a return edge, approximately 2-3mm, giving the appearance of thickness and depth. Back Armor has no visible attachment methods and is not visible from the front or the sides while the cape is worn.

---

	Right Shoulder Armor (Option 1) Right shoulder armor is symmetrical with a single vertical raised ridge, top to bottom with a return edge approximately 2-3mm, giving the appearance of thickness and depth. This armor is only worn with the ‘no blaster dent’ version of the Chest Armor. The upper 1/3 of the shoulder armor is blue (Similar to PMS 537 C) and the lower 2/3 is greenish-tan (Similar to PMS 4250 U).
	OPTIONAL Level two certification (if applicable): Armor is raised up slightly from the shoulder, away from the flight-suit, without any visible attachment method.

---

	Right Shoulder Armor (Option 2) Shoulder is painted the same uniform dark chrome as the helmet and has distinct, symmetrical square-shaped, raised edges. *Armor features a vertical raised ridge from top to bottom, approximately ½ inch in width. There is no visible damage on the shoulder and little to no weathering.
	OPTIONAL Level two certification (if applicable): This armor is worn with the ‘blaster dent’ version of the Chest Armor. Armor is raised up slightly from the shoulder, away from the flight-suit, without any visible attachment method. Shoulder armor is painted in a way that closely resembles the Alumaluster finish seen on screen. A groove is visible and follows all the raised edges where they meet the face of the armor, approximately 3-4mm in width. One small rivet detail is present on each side of the vertical raised ridge at the top.

---

	Left Shoulder Armor Shoulder armor is symmetrical with a raised rounded edge around it’s perimeter. Armor is painted in the same color scheme as the Chest Armor.
	OPTIONAL Level two certification (if applicable): Armor is raised up slightly from the shoulder, away from the flight-suit, without any visible attachment method.

---

	Left Gauntlet Gauntlet is the pre-Blurg attack version and is painted in the same color scheme as the Chest Armor. Center top features three steps with 4 additional smaller details throughout the sides off the gauntlet. An elongated trapezoidal greeblie detail that tapers outward slightly appears on the outer side of the gauntlet. Inner side has rectangular grooved shape above closure. Keypad is silver and weathered to look rusty with 4 horizontal rows of 5 circular buttons. A silver and black detail greeblie is preset just above the keypad.
	OPTIONAL Level two certification (if applicable): Gauntlet is a clamshell style without any visible closure methods. There is an embossed rectangle on the face of the outer greeblie detail. The center 3 buttons of each row of the keypad are slightly larger than the outside buttons.

---

	Right Gauntlet Gauntlet is the pre-Blurg attack version and is painted the same color scheme as the Chest Armor. Center top features three steps with three additional smaller rectangular side details. A recessed red LCD-style display is present and encased by a separate frame with distinguishable edges that sits in a cradle on the top of the base shell at the forward-most section. 4 silver darts are present at the forward edge of the back step of the gauntlet and do not extend past their housing area. Right-outer side of the gauntlet features a raised platform with detached rows on the top and bottom that hoists a small metallic flamethrower. The flame unit is fed into the back from the gauntlet shell and consists of thin piping that tapers forward in sections, with multiple contrasting details throughout. An elongated trapezoidal greeblie detail is visible on the outer side off the gauntlet, next to center section. Inner side of the gauntlet has a rectangular grooved shape above the closure.
	OPTIONAL Level two certification (if applicable): Gauntlet is a clamshell style without any visible closure methods. Display on right gauntlet is functional and flashes/cycles Mandalorian characters. Darts and flamethrower are metal.

---

	Hand Plates Hand Plates are off-white (Similar to PMS WarmGray-1C) with a blue triangle (Similar to PMS 2141 C) in the center. Each plate has eight sides of varied length, with approximately 45-degree angled sides that wrap around the back of the hand. There are 6 discernible sections and a noticeable lip that surrounds the diameter of each plate. Plates secure to the Gloves without any visible means of attachment.
	OPTIONAL Level two certification (if applicable): The blue triangle is slightly raised.

---

	Kidney Armor Kidney Armor wraps around the entire back of the body at the waist. Armor is the same color as the chest armor (Similar to PMS 483 C). Armor plate has five visible sides, and ends at the middle of wearer’s buttocks. Top edge of armor rests under the Ammo Belt without any visible attachment method.

---

Hip Armor Hip armor is dark blue (Similar to PMS 2138 C), with slightly darker blue/black weathering. Both Armor plates are identical and worn on the right and left hip. Armor has two indented ridges, mirroring outer side curvature which run top to bottom. Ridges separate the plate into thirds with one large center section and two smaller side sections. Top of the hip armor is flush with the bottom of the ammo belt, without any visible attachment method.

---

Thigh Armor Armor plates are pre-Mudhorn encounter. Thigh armor has a return edge, approximately 2-3mm with raised edges, giving the appearance of thickness and depth. Right Thigh Armor is painted in the same color scheme as the Chest Armor and features a raised bar in the middle of the plate that merges into a square-shaped raised edge around the entire piece. Left Thigh Armor is painted the same color scheme as the Option 2 Right Shoulder Bell and Features a curving vertical, indented ridge, running top to bottom on the inner side of the armor. Armor features a square-shaped raised edge around the entire perimeter. Thighs are worn on Flight Suit without any visible attachment method.

---

	Left Knee Armor Knee armor is a bluish gray, with a noticeably thicker return edge. Armor is Boba style knee armor and flares outward at the back of the knee on each side. Two identical metallic, hollow dart launchers are attached on the outside of the knee. Each dart has an end lip, then tapers wider to three grooves before terminating into the armor. Knee armor appears to be secured by a leather or leather like strap that attaches to the back face of the armor.
	OPTIONAL Level two certification (if applicable): Strap is made of leather. Dart launchers are metal. On the side wall facing the launchers, an elongated trapezoidal greeblie is present with a visible rectangular groove inside the perimeter of the outward face of the detail. Two visible Philips head screws attach dart launchers to the housing on the back face of the armor.

---

	Right leg Greave Right Greave is a modified Shore Trooper Greave, closing in the back. A“T” plate is affixed to the top of the Armor, covering the knee. Bottom diamond of the “T” is large and not recessed, unlike a Shore Trooper “T” plate. Wings of the “T” plate extend past the diamonds on the armor to the top of the Shin ammo belt. Middle vertical ridge is filled in with a single groove running vertically over the length. Diamonds at the top of the vertical ridge are symmetrical to each other. Edges of the diamonds are equal length unlike Shore Trooper. “T” plate is the same color and weathering as the Chest Armor. Greave is a darker brown color (Similar to PMS 7532 C). Right Shin has a single piece of leather or leather-like strap near the bottom edge approximately 2” tall, closing in the back with 2 square indentations showing after closure. An ammo belt is present on the upper portion of the Armor, directly below the T. The belt is made of leather or leather-like material, wrapping completely around the leg and holds 6 metal looking ammo canisters, each with two ridges at the top and bottom. Material of the ammo belt is 2 different shades. Main belt is dark brown with a reddish-brown center strip. The loops for the ammo canisters are the same reddish-brown. Closes in the back without any visible attachment method.
	OPTIONAL Level two certification (if applicable): The ammo belt and lower strapping is made of leather. The main section of the ammo belt is two sided with the darker back side visibly wider than the dark brown front that is stitched to it. The leather strapping holding the ammo canisters in place, weaves in and out of the front of the main belt to form the holders for the canisters, wrapping around the back of the leg in the center of the belt. Rectangular stitching is visible in between the ammo canisters with the edges of the main belt and canister loops having straight-stitching. Ammo canisters are made of metal and hollow at the bottom.

---

	Left Leg Greave Left Greave is comprised of 3 layered sections of leather or leather-like material. Top section of the greave is a large strap/belt, similar in size to the right leg ammo belt, made of a thick dark brown and a lighter slim brown strip of rigid leather or leather-like material, the slim strap sitting on top off the wider strap in the middle. A small square pouch, 1” thick and approximately the height of the wider strap, rests on the outside of the lower leg, just below the dart launchers. Pouch is the same brown as the top strip of leather and has a flap closure with a metal looking post at the bottom to hold it closed. Upper Strap/Belt covers the top of the main length of the Greave, which is dark brown leather or leather-like material and tucks into the lower section. Both the longer main length and the upper strap/belt close right over left just behind the rear of the pouch via black Velcro. The longer, darker brown length noticeably bunches between the upper and lower sections. The lower section resembles a boot gaiter where the top is a lighter brown leather or leather-like material that attaches to a lower section that sits just above the ankle and is reddish-brown featuring four evenly spaced quilted ribs. The gaiter closes in the back, left over right.
	OPTIONAL Level two certification (if applicable): The entire Greave and all of its components including the pouch are made of heavily distresses leather. The Greave pouch flap is layered to encase the closure strap. In the back, the boot-gaiter enclosure flap rounds out at the bottom while the overlapped material is not and is overlapped significantly by the rounded flap.

---

	Cape Cape is made of wool or wool like material and is dark gray (Similar to PMS 418 C). Cape covers the shoulders and is wide enough to bunch up across the back and shoulders. Four pleated sections on the left, cross in front of the neck, slightly covered by Chest Armor and attach to the opposite side. If the cape is attached to the Flight Suit to aid in maintaining location, any attachment methods are not visible . The bottom edge is heavily tattered. Cape extends to between the mid-shin and ankle.
	OPTIONAL Level two certification (if applicable): Cape is made of boiled wool. Cape has a slit opening so the rifle strap can hold the rifle on the outside of the cape.

---

	Flak Vest Flak vest is a light tan (Similar to PMS 7506 C) and made of cotton/cotton-blend, plain-weave material, similar to duck cloth/canvas. Edges of the vest have a single visible stitch line. Shoulder straps are made of leather or leather-like material that connects the front and the back. Flak vest closes in the back so that any closure method is invisible when the back plate is worn. Flak vest has a single quilt that runs horizontally around the entire vest, lining up approximately with where the Ab Plate attaches to the Breast Plates. The vest is slightly weathered.
	OPTIONAL Level two certification (if applicable): Vest bottom stitch line ends at the bottom of the Ab Plate. A horizontal quilt line is present at same location where the Ab Plate meets the Breast Plates. A “V” shaped quilt pattern is visible on the front of the vest, under the Chest Armor. Bottom two stitch lines are silver theread.

---

	Flight Suit Flight Suit is a grayish brown (Similar to PMS 405 C) and made of cotton/cotton-blend, plain-weave material, similar to duck cloth/canvas. Can be one or two piece in construction. Two piece construction must give the appearance of being one piece when worn. The Flight Suit has double sleeves: Short sleeves have an extra strip of fabric added at the bottom and two vertical strips front and back of the shoulder when arms are down. Has white stitching details on the middle of the sleeve. The long sleeves have 5 horizontal lines, evenly spaced that cover the area between the bottom of the short sleeve and top of the Gauntlet. The long sleeves have decorative crisscross stitching on the back. From waist down, legs feature a single “double-line” detail in the back. The front starts with a single “double-line” and just above the knees, begins an additional detail line. There are reinforced patch areas on the inside of the thighs, made of the same material as the Flight Suit. Flight Suit is worn so that no closure methods are visible. Flight Suit is lightly weathered, and no visible pockets, zippers or logos when all costume components are attached.
	OPTIONAL Level two certification (if applicable): Flight Suit is a one piece jumpsuit.

---

	Neck Seal Made of the same material as the Flight Suit and weathered identically. Neck Seal closes in the back, right over left via Velcro and covers all of the wearer’s neck. No part of the costumer’s chin, neck or ears are visible. Neck seal contains four vertical stitching lines, evenly spaced and of varied length, on each side of opening. Two shorter end at 90-degree angle and wrap around front of throat, following the curve of the seal. Next two form an altered triangular shape. Neck Seal should appear to be attached to the Flight Suit.
	OPTIONAL Level two certification (if applicable): Neck Seal is attached to the Flight Suit.

---

Cummerbund The Cummerbund is an off-brown (Similar to PMS 4250 U). Cummerbund is comprised of three sections made of cotton/cotton-blend, plain-weave material, similar to duck cloth/canvas. The front section is smooth and covers the front of the abdomen, extending into a trapezoid shaped cod-flap that is surrounded entirely by a single stitch line. On each side of the front section are five evenly spaced, horizontal ribs which wrap around the sides and close in the back without any visible closure method when wearing the Back Armor and Flak Vest. Cummerbund is wide enough to cover from the bottom of the Flak Vest to the Ammo Belt. No Flight Suit is visible between them. The bottom of the Cummerbund on the sides, line up with the bottom of the Ammo Belt such that the bottom edge is not seen. The front section extends past the belt, just short of the bottom of the zipper fly on the Flight Suit and is trapezoidal in shape. **The bottom corners of the trapezoid are softly rounded.. Cummerbund is slightly weathered.

---

	Bandolier and Ammo Belt Bandolier, Ammo Belt, pouches and strapping are all made of leather or leather-like material. Bandolier attaches to the inside of the Ammo Belt at the front ammo canister loops and slings up and over the wearer’s left shoulder, attaching to the belt in the back, close to the center. On the back side, a small slotted pocket between the ammo loops and the Phase Rifle buckle is present and a slide is present that separates the Bandolier into two sections. Bandolier has a small shoulder pouch and 6 ammo loops, but only four silver blaster charges are present; second from the top ammo loop and bottom ammo loop are empty. A silver buckle that connects the Amban Phase Rifle strap is present below shoulder pouch at just above the center of the left breast plate. Ammo Belt buckle appears to be meatal with two screw heads visible on the front of the buckle, in line with the top and bottom indents with belt slack held in slotted pockets of the Belt with two smooth headed rivets on each side securing it. Featured on the Ammo Belt, starting from buckle and moving to the left (facing): A cylinder pouch with tooling lines top and bottom that run horizontally. Two ammo loops with silver blaster charges. Sidearm holster. Two ammo loops with silver blaster charges. A metal or metal like plate with four flat-headed rivets and loop with rounded metal snaps to hold Amban Phase Rifle at a slanted angle. Two ammo loops with silver blaster charges. A Breach charge holder that appears to be metal backing with a bottom section that is wrapped in leather or leather-like material, holding three separate charges that appear to be metal, with furled edges and a translucent red domed center lens, all fitting flush in holder. One leather pouch, slightly taller than Ammo Belt width. Features a single gold rivet attaching the strap to pouch flap and silver post at bottom to secure strap. Ammo Belt bottom edge sits flush with the bottom of the Cummerbund sides. Bandolier and Ammo Belt is slightly weathered.
	OPTIONAL Level two certification (if applicable): Ammo Belt Ammo loops are tooled top and bottom with a horizontal line and stitched in place on both sides of the loops. Bandolier, Ammo Belt, pouches and strapping are all made of leather. Breach charges, blaster charges, Ammo Belt buckle, Amban Rifle buckle and Bandolier slide are metal and removable.

---

	Gloves Gloves are leather/leather-like material consisting of two sections. Black section of the gloves are fingerless and extend past the wrist with the edge of the glove long enough so that it is not visible when the wrist is bent. Heavily weathered orangish-yellow fingers (Similar to PMS 4017 C) extend out beyond fingerless black section. Logos and any other non-canon details are not visible.
	OPTIONAL Level two certification (if applicable): Fingers are a separate layer.

---

	Pistol Holster Made of rigid leather/leather-like material. Hangs from the Ammo Belt with two belt loops on the wearer’s right hip. A single strap that slips through a flat loop holds the Pistol in place. Holster is weathered to reflect regular use.
	OPTIONAL Level two certification (if applicable): Holster and straps are leather and conforms specifically to the shape of the Mandalorian Blaster Pistol.

---

	Boots Chelsea style boots with black rugged soles and a slight heel. Light brown leather or leather-like material with a stitched details and sections running over the entire boot. Inner side of the boot at the ankle has a weathered light blueish-gray patch that extends upward to the top of the boot. Top of the boot is hidden under the shin armor. Elastic, Velcro or any other closure methods are invisible.
	OPTIONAL Level two certification (if applicable): Base of the boots are made from Sketchers Brand - Blaine Orsen Boots, or boots closely matching. All detail sections covering the base boot are leather.

---

Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below. If adding in an accessory after initial approval, the item still needs to be submitted to local GML for approval before use.

	Vibro-Boot Knife Is inserted into the outside of the right shin armor and only the handle is visible. Can be just the handle if permanently attached to the inside of the right shin armor. The handle is blue (Similar to PMS 2138 C) and heavily weathered, exposing the appearance of metal underneath. Knife is approximately 9 inches in length including the blade.
	OPTIONAL Level two certification (if applicable): Knife is removable and vibrates.

---

	Amban Sniper Rifle Rifle is proportionate to the height of the costumer. Rifle body is black with gold and silver accents. Stock of the rifle is brown and made to resemble wood. Prongs of the rifle are silver and finished to show heavy heat discolorations. Body of the rifle has heat discolorations. Rifle is slightly weathered. Scope can be permanently attached or removable. Has a strap connected with a metal buckle that attaches the rifle to the bandolier.
	OPTIONAL Level two certification (if applicable): Stock is made of wood.

---

	Blaster Pistol Based on a Bergmann 1896 pistol. Conical muzzle has a forward black section that includes the iron sight with a rear silver section that connects to the barrel. Sidearm has a black body and a reddish grip. Sidearm is weathered.
	OPTIONAL Level two certification (if applicable): Sidearm is a Bergmann 1869 pistol or direct replica.

---

• This CRL is available as a PDF

This document and all of the images within were created by and are the property of the 501st Legion. Other media owned by Lucasfilm Ltd and Disney are used under authorization. All other uses are prohibited. The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it follows generally accepted ground rules for Star Wars fan groups. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. Copyright and Trademark Lucasfilm Ltd. All rights reserved. Used under authorization.