Gear Cutters 01

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

Making Milling Cutters

for cutting gear wheels


by D. J. Unwin
IT IS MUCH more satisfying when building a model
or clock involving gearing to cut the gears oneself.
Whilst commercial gearing is usually produced
by a generation process, quite satisfactory results
can be obtained by cutting each tooth separately
with a form cutter on the lathe or milling machine
using a dividing device to space the teeth. Methods
of doing this and the necessary gearing calculations
are fully described in the M.A.P. Handbook by
Alfred W. Marshall, Gearwheels and Gear
Cutting. If you intend to make any. gearing, it
can be thoroughly recommended and will explain
the various terms used.
The cutter used must be of the correct form to
produce a tooth of the right shape. These are
available commercially but are rather expensive.
However, they are not difficult to produce on the
lathe using simple form tools and the method of
production was described in M.E. Aug. 21, 1970.
It is also much more satisfying to carry out the
whole job personally.
There are two types of gear tooth forms which we
are most likely to need to cut, the Involute form for
ordinary power transmission and the Ogival type
for clock work. As slightly different method are
needed to produce the forms, I will describe them
separately and deal with the involute gear cutter
first.

The Involute Form


The basis for producing the cutter is the single
curve approximation to the involute gear shape, the
calculations for which were originally published by
the Brown and Sharpe Co. of U.S.A. It is also
given in Gears for Small Mechanisms by W. 0.
Davis in which an additional correcting factor for
gears with less than 20 teeth is described. This
has been included in the values given in the tables
of sizes given for making the form tools which are
used to shape the gear cutters.
Fig. 1 shows details of the form tool. It consists
of a piece of mild steel bar with two accurately
spaced holes into which are clamped two turned
hardened pins which form the cutting edges.
The diameter of the pin, the in-centre distance,
the amount of in-feed and the blank width are
obtainable from Table 1. The cutting depth of
the finished gear cutter is also given. A choice of
two pressure angles is given. That normally used
is 20 deg., but if a pinion with very few teeth is
966

required, 30 deg. pressure angle gives a stronger


tooth without undercutting at the root.
The tables are given for 1 D.P. and to get the
actual dimensions required to make a cutter it is
only necessary to divide all the values by the
required D.P. number (Diameter Pitch). i.e.
20 deg. pressure angle.
Cutter No. 3-35 to 54 teeth 50 D.P.
then d dia. of pins
0.239 in.
c centre of pins
0.253 in.
f in-feed
0.062 in.
w width of blank 0.08 in.
In those cases when the pin diameter d exceeds
the centre distance c a flat will need to be ground
or filed on them. It may also be necessary to grind
off the front to clear the mandrel in certain circumstances. In the case of the small pitches, width w
may become rather small to provide a sufficiently
stiff blank. This can be avoided by stepping the
blank as shown in Fig. 4. In fact I usually keep a
small stock of turned but unformed blanks and
produce the edge thickness in this way.

Fig

.1.

.~

Form tool for Involute Gear Cutters.


The shank of the tool can be any convenient piece
of b.m.s. but long enough to clamp in your toolpost,
about 5/16 in. or 3/8 in.thick and wide enough to
accommodate the holes for two pins without being
weak enough to bend under the cutting strain. The
centre distance between the two pin holes should
be as accurate as possible and to ease accurate
setting up they should be perfectly square with the
side. To achieve this they can be jig-bored by
clamping the bar on an angle plate fixed to the toolMODEL ENGINEER I October 1971

TABLE 1
INVOLUTE CUTTER PROPORTIONS
For 1 DP or 1 Module
30 deg. PRESSURE ANGLE (Cos 0 = 0.866)
C UTTER R A N G E
No.
T%H

PIN
D I A.
d

PIN
ENTRES

1
135-R
67.5
59.5
~~~___
2
55-134
27.5
25.0
3

35-54

17.5

FEED
IN
f

BLANK
W IDTH
W

3.20

4.0

2.85

4.0

16.3

2.67
4.0
~~
4
26-34
13.0
12.4
2.54
4.0
-~
~5
21-25
10.5
10.25
2.41
4.0
~~-___
6
17-20
8.5
8.5
2.31
4.0
-~
~___
7
14-16
7.0
7.2
2.18
4.0
~--~8
12-13
6.0
6.36
2.06
4.0
~~-9
10-11
5.0
85.6
1.98
4.0

TABLE la
INVOLUTE CUTTER PROPORTIONS
For 1 DP or 1 Module
20 deg. PRESSURE ANGLE (Cos 0 = 0.93)
C UTTER R A N G E
FEED
B LANK
PIN
PIN
No.
D I A.
C ENTRES IN
W IDTH
T;:H
d
C
f
W
~--___ ~1
135-R
46.17
44.80
3.934
4.0
2
55-134 18.81
19.07
3.415
____~
~___
12.64
3.098
3
35-54
11.97
______4
26-34
8.89
2.875
9.75
___~
2.710
5
21-25
7.18
8.147
6
-

17-20
-

14-16

8
12-13
~~
9
IO-11

5.81
-

4.788

4.0
4.0
4.0
4.0

6.864

2.543

4.0

5.905

2.387

4.0

4.100

5.267

3.42

4.632

c
Fig.4.

Stepped blank for small pitches.

The cross hole for the clamping bolt, say 4 or


2 BA, depending on size of the tool, can be drilled

and the slots for clamping sawn by hacksaw or


milled. Turn the pins from cast steel or silver
steel, making the shanks a good fit in the shank.
Take care to get the diameter d accurate. Harden
and temper to light straw, then polish up the
larger diameter in the lathe. Clamp them both in
the shank and lightly grind across the tops to get
them level and sharp, then finish up to a good
finish on a flat oilstone to remove all burrs.
The tool is now ready to be used to produce the
form milling cutter. Whilst these can be single
point fly cutters for light alloy or brass, I strongly

2.251
4.0
_______
2.108
4.0

post. The index of the cross-slide can be used to


measure the centre distance and the holes which are
centred, drilled and reamed by holding the tool in
the chuck and using the top-slide to provide the
feed. The size of holes is unimportant provided
that it allows a shank on the pin of sufficient
diameter not to break when cutting.
MODEL ENGINEER I October 1971

Showing flats on pins,

Diagram for TABLE.l.


967

recommend making multi-tooth cutters. Once


made these cutters can be used for any future job
regardless of material.
Prepare the cutter blank, including turning the
edge to the correct width w, as described in my
earlier article. Set up the form tool, taking care to
ensure that it is perfectly square with the axis of the
lathe. If the holes have been carefully drilled,
then the side of the shank can be used. If not, the
front edges of the pins must be set parallel to the
axis by carefully lining them up to a parallel
mandrel.
When correctly set up, each of the two pins
must be located precisely with respect to the blank
so that they are both just touching on each corner
(Fig. 7). The cross-slide index collar figure is then
noted or set to zero, the lathe started up on a slow
speed and the tool carefully fed in the required
amount f. When completed on each tooth our
form tool has finished its task and we can go ahead
and complete the milling cutter.
Before hardening, mark the cutter with-the
D.P. number, the cutter number, the range of teeth
and the cutting depth.

TABLE 2
OGIVAL CLOCK TOOTH PROPORTIONS
For 1 DP or 1 Module
PINION l/3 OGIVE
D!?
1
34
40
42
44
48
52
----_-_-a
0.74 0.022 0.019 0.018 0.017 0.016 0.014
b
1.75 0.052 0.044 0.042 0.040 0.037 0.034
_
s
1.99 0.059 0.050 0.048 0.045 0.042 0.038
r
0.77 0.023 0.019 0.018 0.017 0.016 0.015
a + b 2.49 0.074 0.063 0.060 0.057 0.033
0.048
e
1.15 0.034 0.028 0.027 0.026 0.0239 0.022
--_-_---N
6
7
8
9
10
11
12
13
-----P--P
0 deg. 30
13.8
25.5
22
20
18
16
15
a, A Addendum = 0.74
dp

b, B Dedendum = 1.75
dp

e, E

r, R Radius = 0.77
dp

Tooth width = 1.15


dp

s, S Space width = 1.99


dp
0

Angle of radial sides = 180


N

dia. of blank = N + 1.48


dp
N

Number of teeth

TABLE 3
OGIVAL CLOCK TOOTH PROPORTIONS
For 1 DP or 1 Module
GEAR

Lining up the form tool on the blank.


It is worth noting that the tables can be used
when it is required to make a metric module cutter;
I have made several such cutters for repair jobs.
All that is necessary is to remember that the gear
module is the reciprocal of D.P., i.e. the metric
PCD,
module is defined as the N PCD being in mm.

DP
1
34
40
42
44
48
_--P-P-

1.57

0.046

0.039

0.038

0.036

A+ B

2.90 0.085

0.073

0.069

0.066

Therefore by multiplying the values in the table by


the metric module needed, the result is the required
dimension IN MILLIMETRES
Cutter No.
i.e. 0.5 module
Cutter No. 3, 35-54 teeth
N
1 (21/25/26/34135/54/55/134(;;l35k
1
20 deg. Pressure angle
-I-I-I-II-!
d Dia. of pin
= 5.985 mm
0 deg.
9
6.9
5.1
3.3
1.3
c Centre of pin = 6.32 mm
Parallel for
f In feed
= 1.549 mm
Practical
w Thickness
= 2.000 mm
Purposes
Alternatively if you prefer to work in inches _

968

MODEL ENGINEER I October 1971

+I

Diagram for TABLE .2.


throughout, convert the required metric module to
English D.P. by dividing 25.4 by the D.P.
25.4
i.e. o5 = 50.8 then carry on by dividing these
values as before. Remember the dimensions will
now be in INCHES.
We will now deal with the Ogival clock tooth
form.
For clock work, in which the train is usually
stepping up, and where low friction is more important than a constant velocity ratio, the Ogival
approximation to the epicycloidal tooth is often
used. There are a number of variants, but the one
I have used successfully is the 1/3 Ogive in which the
tooth form is not dependent on the gear to pinion
ratio. If any reader should prefer to use any other
form such as BS.978, the same methods of making
the form tools for making the cutters can be applied.
Unlike involute gear cutters, I use single point fly
cutters for gears, which are almost invariably of
brass, whilst using multi-point cutters for pinions
which are usually of mild steel or cast steel.
Table 2 gives the proportions of shape for 1 DP
(or 1 module) pinion. As in the case of involutes,
to get the values required:
Divide by the DP, dimensions in inches. Multiply
by the module, dimensions in mm if metric module.
Note that in this case the flank angle 0 should be
chosen to suit the number of teeth the cutter is
going to be used to cut. Table 3 gives the same
values for gearwheels.
In addition to the basic proportions, I have also
given the values for a few common DPs used in
clock work. It will be seen that even in the case
MODEL ENGINEER I October 1971

Diagram for TABLE.3.


of the larger teeth sizes such as 34 DP, typical of the
size used on a clock great wheel, the radii R and r
are quite small. This, together with the need for
radial flanks, demands a different approach from
that used to make involute shapes.
Taking the coarser pitches of gears say from
40 DP, I made pin form tools similar to those used
for involutes. The main difference was that the
pins consisted of short pieces of hardened silver
steel of the required diameter (2R or 2r) and no
attempt was made to achieve the correct centre
distance. The holes to receive the pins were
drilled about 1/2 in. apart at an angle of about 5 deg.
from the vertical, in such a manner that both side
and front clearance are given to the cutting edge.
(See Figs 8 and 9, next issue.)
The blank, either a piece of square cast steel for
a fly cutter for cutting gears, or a prepared disc for
a multi-tooth cutter for making pinions, is mounted
in the lathe and the pin form tool mounted in the
tool holder with the two cutting edges parallel to
the lathe axis. Using the appropriate cutting pin,
one side is carefully machined to the correct depth
(r + b). The amount to be machined from the
side of the blank is given by:
Blank thickness - S
2
After completing the first side, machine the other
side using the opposite cutting point. By careful
measurement of the blank, and use of the top-slide
indexes, the correct thickness S can be achieved,
although it can be checked by direct measurement
using a micrometer. If anything, be slightly undersize, not oversize.
To be continued.
969

You might also like