Professional Documents
Culture Documents
Sarnafil G 410 L Felt
Sarnafil G 410 L Felt
Zurück
Table of Contents
Application Details
Substrate Quality The substrate surface must be uniform, smooth and free of any sharp protrusions or
burrs. The supporting layer must be compatible to the membrane, clean, dry and
free of grease and dust.
Application
Conditions / Limits
Temperature The use of Sarnafil G 410 L Felt membrane is limited to geographical locations
with an average monthly ambient temperature in the range of -30 C to +50 C.
Compatibility Sarnafil G 410 L Felt is not compatible with direct contact to other plastics, e.g.
EPS, XPS, PUR, PIR or PF. Sarnafil G 410 L Felt is not resistant to tar, bitumen,
oil and solvent containing materials.
Installation
Instructions
Installation Method / Refer to the Sika Installation Manuals for single ply PVC membranes.
Tools Sarnafil G 410 L Felt is bonded to the substrate by a suitable Sarnacol adhesive
(see Sarnacol product documentation).
Overlap seams are welded by electric hot air welding equipment, such as manual
hot air welding machines and pressure rollers or automatic hot air welding
machines with controlled hot air temperature.
Recommended type of equipment: Leister Triac PID (manual welding) and
Sarnamatic 661plus (automatic welding)
Welding parameters including temperature, machine speed, air flow, pressure and
machine settings must be evaluated, adapted and checked on site according to the
type of equipment and the climatic situation prior to welding. The effective width of
welded overlaps by hot air should be minimum 20 mm.
The seams must be mechanically tested with screw driver to ensure the integrity /
completion of the weld. Any imperfections must be rectified by hot air welding.
Notes on Installation / Installation works must be carried out only by Sika instructed and approved roofing
Limits contractors.
Temperature limits for the installation of the membrane:
Substrate temperature: -30 C min. / +60 C max.
Ambient temperature: -20 C min. / +60 C max.
Installation of some ancillary products, e.g. contact adhesives / cleaners is limited to
temperatures above +5 C. Please observe informatio n given by Product Data
Sheets.
Special measures may be compulsory for installation below +5 C ambient
temperature due to safety requirements in accordance with national regulations.
Local Restrictions Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.
Ecology, Health A Safety Data Sheet following EC-Regulation 1907/2006, Article 31 is not needed
to bring the product to the market, to transport or to use it. The product does not
and Safety damage the environment when used as specified.
Information
Protective Measures Fresh air ventilation must be ensured, when working (welding) in closed rooms.
Local safety regulations must be observed.
Transportation Class The product is not classified as hazardous good for transport.
Disposal The material is recyclable. Disposal must be according to local regulations. Please
contact your local Sika sales organisation for more information.
Construction
Legal note: The information, and, in particular, the recommendations relating to the application and end-
use of Sika products, are given in good faith based on Sika's current knowledge and experience of the
products when properly stored, handled and applied under normal conditions in accordance with Sika's
recommendations. In practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising
out of any legal relationship whatsoever, can be inferred either from this information, or from any written
recommendations, or from any other advice offered. The user of the product must test the products
suitability for the intended application and purpose. Sika reserves the right to change the properties of its
products. The proprietary rights of third parties must be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which will be supplied on request.