A133996 PDF
A133996 PDF
7.Presented at
the 56th Meeting of the Structures and Materials Panel, in London,
United Kingdom on 10-15 April 1983.
8.Author(s)/Editor(s) 9. Date
L.Balis Crema and A.Castellani August 1983
Airships
Design
Composite materials
Carbon fibers
Performance
14.Abstract
HK^^mH
ADVISORY GROUP FOR AEROSPACE RESEARCH & DEVELOPMENT
Some Trends in
Airship Technology Developments
by
Paper presented at the 56th Meeting of the Structures and Materials Panel,
in London, United Kingdom on 10-15 April 1983.
THE MISSION OF AGARD
The mission of AGARD is to bring together the leading personalities of the NATO nations in the fields of science
and technology relating to aerospace for the following purposes:
— Continuously stimulating advances in the aerospace sciences relevant to strengthening the common defence
posture; - ,
— Improving the co-operation among member nations in aerospace research and development; ^
— Providing scientific and technical advice and assistance to the North Atlantic Military Committee in the field
of aerospace research and development; ■ '
— Rendering scientific and technical assistance, as requested, to other NATO bodies and to member nations in
connection with research and development problems in the aerospace field;
— Providing assistance to member nations for the purpose of increasing their scientific and technical potential;
— Recommending effective ways for the member nations to use their research and development capabilities for
the common benefit of the NATO community.
The highest authority within AGARD is the National Delegates Board consisting of officially appointed senior
representatives from each member nation. The mission of AGARD is carried out through the Panels which are
composed of experts appointed by the National Delegates, the Consultant and Exchange Programme and the Aerospace
Applications Studies Programme. The results of AGARD work are reported to the member nations and the NATO
Authorities through the AGARD series of publications of which this is one.
Participation in AGARD activities is by invitation only and is normally limited to citizens of the NATO nations.
ISBN 92-835-1458-0
Increasing attention is being now paid to the possibility of using dirigibles more widely
because of the flexibility of performance of the lighter-than-air (LTA) concept. Attention is
being focused on the potential improvements offered by advances recently made in aerospace
technology. For its part, the Structures and Materials Panel has an interest in the application
of new materials and novel structures, and an activity to consider those aspects has been set
up by the Panel at its Spring 1983 Meeting in London.
This pilot paper was presented at this Meeting. It demonstrates that significant reductions
in structure weight can be achieved through the use of new materials, such as carbon fibre
composites, and goes on to show what corresponding improvements in operational performance
can be gained.
The data given here are encouraging; they provide a starting point for future developments.
P.SANTINI
Chairman, Sub-Committee on
Materials & Structures for Dirigibles
III
CONTENTS
Page
PREFACE
by P.Santini
SUMMARY 1
INTRODUCTION 1
2. PERFORMANCE ANALYSES 2
4. PROBLEM AREAS - 6
REFERENCES ' 6
\
by
SUMMARY
Some problem areas for the advance of modem airships are pointed out.
A typical long range sea patrol mission is considered.
In particular the use of composite materials for the structure and for the envelope, in order to achieve a substantial reduction of
the empty weight and consequently a performance improvement, is considered.
INTRODUCTION
Recently several proposals for the hghter-than-air (LTA) aircraft use have been presented, which take into account technological
advance in structural materials, propulsion systems and control techniques. It is claimed that such advances would permit the design
of new airships which are both safer and more efficient.
Such kinds of design include light weight envelopes and structures, light weight engines and advanced controls and instrumentation.
Thus a modem airship would have better performances than historical airships of comparable volume.
However the obvious hmits of the airship that make it non-competitive whith commercial air transport lead to deeper inspections
for special missions of the airships. The most appealing apphcation for a modem conventional airship could be a long range maritime
patrol mission, because of the payload capacity and endurance.
The airships have higher speed than ships and greater endurance and higher payload capacity than airplanes [1 ].
In order to evaluate the airship efficiency the first item to be considered is the empty weight (') effect.
The ratio empty weight to volume (Wj/V) versus volume for several airships — Akron, Macon, Hindenburg included is shown in
Fig.l.
We kg
m^
'
LZ 121
*
N1 LZ 127 Fig.l
^LZ120n'' ■ ZR' LZ 126
* ZR_4
ZR-5
« LZ129
'" ZPG3W* *
0 L.Z72
.5- ZPX
ilt
SMD 100
o 4060 A
WDL 3
o o
#=rig id
n=semi--rigid
A=all- metal
0= proposed
,
50 100 150 200
V-io^'m^
(' ) The empty weight is given by the gross weight less lifting gas weight and useful and fuel weight.
One can see that, despite the replacement of steel with aluminum alloys in the rigid structure, this ratio is close to being practically
constant as volume increases.
Therefore the efficiency does not increase with size, typical values of current technology are in the area Wj/V = 0.55 kg/m^. The
contribution of the individual parts of the rigid airship to the above values are shown in Table 1.
COMPONENTS We/V(kg/m')
* for the semi-rigid and non-rigid airships the value changes to .2 and .3
Several proposed airships, which could use new lighter structural materials, are considered in Fig. 1 [4].
As one can see the ratio We/V is significantly reduced and a more advanced value We/V = .35 might be achieved with current
technology.
Empty weight also affects cruise altitude. For We/V = .5 and We/V = .3, values of the ratio of useful load at various altitudes,
Wu, and useful load at sea level, Wuo, versus altitude, are presented in Fig. 2, for helium practical lifting force of 1 kg/m^.
It appears that the empty weight effect on the altitude capability is very significant.
Fig. 2
2. - PERFORMANCE ANALYSES
In order to evaluate the potential effectiveness of modern airships with a reduced structural weight, some performances are presen-
ted by using the drag and propulsive efficiency of designs of the past.
Range increase, d, versus volume for two cruise velocities and several ratios, Wg/V, is shown in Figs. 3 and 4. In this analysis the
ratio Wu/V is kept constant, so that the weight of the fuel, Wf, increases as the ratio We/V is improved. The productivity, (defined by
payload tons » range kilometers) versus volume is presented in Fig. 5.
Conversely if the ratio Wf/V is kept constant (so that the payload increases as the ratio We/V is improved) one gets the values of
productivity, as defined by payload tons * range kilometers/fuel kUos, which are shown in Fig. 6.
But it is important to add another significant parameter such cruise velocity; thus, by redefining the productivity as the ratio (pay-
load range « cruise velocity/fuel required), we obtain the Fig. 7, for a 200,000 m' airship and two ratios We/V.
From the above considerations it is possible to guess a possible configuration of the airship for a sea patrol mission.
For instance Fig. 8 shows for a mission, as defined by range, payload and cruise velocity, the values of volume computed as a
function of the ratio We/V [5], [6].
d-io^km
Fig. 3
d-1oVm We
= .4
V -
^^v=70 km/h
40. ^
^
Fie. 4
30.
^ ^,,^——"^O
/
/
20.
^
.-———TTtO
10.
0.
() 1 2 i i ^
V-io^m^
ton-km-10
Fig. 5
V-10^m^
ton-km
Fig. 6
ton.
4000
Fig. 7
2000
200 V
km/h
5.
d =15000 km
V rn-io"
V = 90 km/h
4-
W„=30 t
Fig. 8
3.
jr
2.
1. /
J
»
^^
^ We kg
0.
c) .2 .4 .6 .8 m"
3. - TECHNOLOGICAL ADVANCE IN MATERIALS
The previous analysis shows that one gets a significant improvement as the ratio Wj/V decreases.
This decrease may be achieved by new structural materials and new fabrics for the envelope [7], [8].
In the field of propulsion, improvements in aircraft engines may allow to save up to 75% of the relevant weight. In this area,
emphasis should now be placed on the thrust vector control tecnique in order to get an autonomous capability in hovering, landing and
take-off.
In the structural materials field one can see a definite trend towards the use of composite materials which have received large
application in the aircraft and spacecraft construction.
As for the primary structure (e.g. girder and rigid frame) is concerned composite materials as carbon fiber and kevlar fiber (see
Table 2 for properties) could be used.
Weight saving, as compared to an analogous aluminum alloy structure, may be as high as 30 percent; that is in agreement with the
prevision of the composite materials application for new design studies concerning primary structures, e.g. the wing, in aircraft structu-
res [9].
A second significant saving can be achieved by using new fabrics for the envelope.
The properties of these materials, which have a large use for the high altitude scientific baUons, are presented in Table 3.
In comparison with the historical envelopes of cotton-reinforced rubber, the new materials use could save about 35 ^ 40 percent.
At last, if also the secondary structural members (e.g. car, control surfaces, rigging, ...) are manufactured from composite materials,
a further saving of 15 percent could be achieved. It is well known that kevlar fibers have been used in the airship AD-500 Skyship.
This approach offers, in the last analysis, reductions in overall weight which could lower the ratio We/V, for the future airships, to
.35 (see Table 4), [10].
In this case, as one can see by Fig. 8, a significant reduction in the system size is achieved.
For example for a typical sea patrol long range mission, defined by a seven days endurance and a 30 tons payload, a reduction in
the ratio We/V from .55 to .35 should permit the use of an airship of 70,000 m' class.
In the Authors' opinion it is possible to indieate the following major problem areas in order to get a signifieant improvement in the
airship performances, based on the technology available in the 90's:
1 — primary structure construction in composite materials; ~
2— secondary structure construction in composite materials; ■ '
3— pliant material technology for envelopes and gas cells;
4— modern computer techniques in analysis of airship structures; " .•■■■■ -^ . ,
5— thrust vector control capabdity; , •
6— airship dynamics and control at low velocities; " '
7— airship operations, ground handling and ground faciUties; "-
8— development of new certification rules.
REFERENCES "
[ 1] R.L. ASHFORD, B.B. LEVITT, F.R. NEBIKER, H.K. RAPPOPORT: "AppUcation of Lighter Than Air Technology in Develo-
ping Countries", UNIDO, Vienna, 19-22 October 1981.
[ 2] C.P. BURGESS: "Airship Design", Ronald Press Company, New York, 1927.
[ 3] T.L. BLAKEMORE, W. WATTERS PAGON: "Pressure Airships", Ronald Press Company, New York, 1927.
[ 4] N.J. MAYER: "Current LTA Technology Developments", UNIDO, Vienna 19-22 October 1981.
[ 5] J.A. ENEY: "U.S. Navy Studies of Surveillance Airships", A.E.R.A.L.L., Paris, March 1979.
[ 6] H.K. RAPPOPORT: "Potential Coast Guard Missions for a Maritime Patrol Airship", A.E.R.A.L.L., Paris, March 1979.
[7] N.J. MAYER: "LTA Structures and Materials Technology", FTL Report R75-2, January 1975.
[ 8] K.G. PAYNE: "Materials for Airship Construction", Aeronautical Journal, Volume 85, N. 482, March 1981, pp. 85-87.
[ 9] R.H. LANGE, J.W. MOORE: "AppUcation of Composite Materials and New Design Concepts for Future Transport Aircraft"
ICAS-82-2.7.3., Seattle 1982.
[10] CD. HAVILL: "Some Factors Affecting the Use of Lighter Than Air Systems", NASA, Ames Research Center.
ACKNOWLEDGEMENT
The authors are indebted to Prof. Paolo Santini who suggested this work and supported it with useful discussions.
AGARD Report No.717 AGARD-R-717 AGARD Report No.717 AGARD-R-717
Advisory Group for Aerospace Research and Advisory Group for Aerospace Research and
Development, NATO Development, NATO
SOME TRENDS IN AIRSHIP TECHNOLOGY Airships SOME TRENDS IN AIRSHIP TECHNOLOGY Airships
DEVELOPMENTS Design DEVELOPMENTS Design
by L.Balis Crema and A.Castellani Composite materials by L.Bahs Crema and A.Castellani Composite materials
Published August 1983 Carbon fibers Published August 1983 Carbon fibers
12 pages Performance 12 pages Performance
Recent advances in aerospace technology, and in par- Recent advances in aerospace technology, and in par-
ticular the application of new materials and novel ticular the application of new materials and novel
structures, have special relevance to the development of structures, have special relevance to the development of
dirigibles. This paper demonstrates that significant dirigibles. This paper demonstrates that significant
reductions in structure weight can be achieved through reductions in structure weight can be achieved through
the use of, for example, carbon fibre composites. It the use of, for example, carbon fibre composites. It
goes on to show what corresponding improvements in goes on to show what corresponding improvements in
operational performance can be gained. operational performance can be gained. 1
P.T.O. P.T.O.
Recent advances in aerospace technology, and in par- Recent advances in aerospace technology, and in par-
ticular the apphcation of new materials and novel ticular the apphcation of new materials and novel
structures, have special relevance to the development of structures, have special relevance to the development of
dirigibles. This paper demonstrates that significant dirigibles. This paper demonstrates that significant
reductions in structure weight can be achieved through reductions in structure weight can be achieved through
the use of, for example, carbon fibre composites. It the use of, for example, carbon fibre composites. It
goes on to show what corresponding improvements in goes on to show what corresponding improvements in
operational performance can be gained. operational performance can be gained.
P.T.O. P.T.O.
Paper presented at the 56th Meeting of the Structures and Materials Panel, in London, Paper presented at the 56th Meeting of the Structures and Materials Panel, in London,
United Kingdom on 10-15 April 1983. United Kingdom on 10-15 April 1983.
Paper presented at the 56th Meeting of the Structures and Materials Panel, in London, Paper presented at the 56th Meeting of the Structures and Materials Panel, in London,
United Kingdom on 10-15 April 1983. United Kingdom on 10-15 April 1983.
AGARD does NOT hold stocks of AGARD publications at the above address for general distribution. Initial distribution of AGARD
publications is made to AGARD Member Nations through the following National Distribution Centres. Further copies are sometimes
available from these Centres, but if not may be purchased in Microfiche or Photocopy form from the Purchase Agencies Usted below.
NATIONAL DISTRIBUTION CENTRES
BELGIUM ITALY
Coordonnateur AGARD - VSL Aeronautica Militare
Etat-Major de la Force Aerienne Ufficio del Delegato Nazionale all'AGARD
Quartier Reine Elisabeth 3, Pia7.7alp A/^
■ Rue d'Evere, 1140 Bruxelles
TANIAriA """^"^ ■
Postage a"<»f««»'^"'„.
Nal^i Aeronaolics and
Space Admioistiaiion
(VI/^/V NASA-4S1
Ollioal Business
o AGARD
National Aeronautics and Penally lor P"vaie use WOO iratory, NLR
space Administration ^^,o,,^ CLASS MA,L
Vteshington.D.C. SPECIAL ^^^^
20546 .;•■.-'. . . , , xc
831014 30Z2/oJb rch Establishment
DHHT OP I'HE
jKADJAi'E bC>lOC)^
J»
J UDLHY KNOX COJE 1424 terial
oJPE<aNT£t^JcNl,
A'I
,.^P^ CA 93940
•A^
;legate
Gl
a Development (ARGE)
..onxui iNaTionalDefence, Ankara
UNITED KINGDOM
ICELAIND Defence Research Information Centre
Director of Aviation Station Square House
c/o Flugrad St. Mary Cray
Reykjavik Orpington, Kent BR5 3RE
UNITED STATES
National Aeronautics and Space Administration (NASA)
Langley Field, Virginia 23365
Attn: Report Distribution and Storage Unit
THE UNITED STATES NATIONAL DISTRIBUTION CENTRE (NASA) DOES NOT HOLD
STOCKS OF AGARD PUBLICATIONS, AND APPLICATIONS FOR COPIES SHOULD BE MADE
DIRECT TO THE NATIONAL TECHNICAL INFORMATION SERVICE (NTIS) AT THE ADDRESS BELOW.
PURCHASE AGENCIES
Microfiche or Photocopy Microfiche Microfiche or Photocopy
National Technical Space Documentation Service British Library Lending
Information Service (NTIS) European Space Agency Division
5285 Port Royal Road 10, rue Mario Nikis Boston Spa, Wetherby
Springfield 75015 Paris, France West Yorkshire LS23 7BQ
Virginia 22161, USA England
Requests for microfiche or photocopies of AGARD documents should include the AGARD serial number, title, author or editor, and
publication date. Requests to NTIS should include the NASA accession report number. Full bibliographical references and abstracts
of AGARD publications are given in the following journals:
Scientific and Technical Aerospace Reports (STAR) Government Reports Announcements (GRA)
published by NASA Scientific and Technical published by the National Technical
Information Facility Information Services, Springfield
Post Office Box 8757 Virginia 22161, USA
Baltimore/Washington International Airport
Maryland 21240; USA
ISBN 92-835-1458-0