HiCOM key teaching manual www.obdtester.

com/hicom

Hyundai/Kia key teaching

Table of Contens
1.SMARTRA introduction....................................................................................................................2
PIN Codes........................................................................................................................................2
2.Supported vehicles.............................................................................................................................3
3.Mechanical keys with RFID chip......................................................................................................5
Teaching...........................................................................................................................................5
4.Smartkey ...........................................................................................................................................7
Teaching...........................................................................................................................................7
5.Key information.................................................................................................................................8
6.Login..................................................................................................................................................8
7.Password Teaching/Changing............................................................................................................9
8.Neutral Mode.....................................................................................................................................9
9.Limp Home Mode...........................................................................................................................10

1 / 10
HiCOM key teaching manual www.obdtester.com/hicom

1. SMARTRA introduction
The SMARTRA stands for SMARt TRansponder Antenna. The SMARTRA unit contains an
integrated inductive antenna and electronics around the ignition lock assembly.

The SMARTRA does not carry out the check of validity of transponder or the calculation of
encryption algorithm. This device is only an advanced interface, which converts the RF data flow
(radio frequency of 125 kHz) of transponder into serial communication to ECM and vice versa.
The SMARTRA communicates to a engine control module via a dedicated communications line
(called W-Line, or Immo-Line). During communication of ECM and SMARTRA the K line of ECM
cannot be used for communication. The ECM controls the communication either to SMARTRA or
diagnostic equipment on K line by switching of a multiplexer and specific communication
procedures. The multiplexer is a part of ECM hardware.
The immobilizer system consists of the ECM, the SMARTRA, the lamp and ignition keys with
built-in transponder. The ECM carries out the check of ignition key by special encryption
algorithm, which runs in the transponder and in the ECM in parallel. Only if the results are equal
the engine can be started. The data of all transponder, which are valid for the vehicle, are stored in
the ECM.
During the key teaching procedure the transponder will be programmed with vehicle specific data.
The vehicle specific data are written into the transponder memory.

PIN Codes
PIN code stands for of Product Identification Number code. The PIN code is a unique code for each
vehicle and it is programmed into ECM at production line.

PIN code is needed when the teaching new ECM and new keys, e.g.
1) When a new key is added
2) When replacing with new ECM or used ECM (neutralized ECM)
3) When a key is lost and needs to be deleted

Vehicle PIN code can be obtained

through www.PATSCode.com
service or through Hyundai dealer.

2 / 10
HiCOM key teaching manual www.obdtester.com/hicom

2. Supported vehicles

Following list shows all vehicles for which is key teaching supported:

Manufact. Model Production Manufact. Model Production

Dodge Atos 2000-2004 Hyundai i10 2008-2011

Hyundai Accent 2000-2011 Hyundai i20 2009-2011

Hyundai Amica 2000-2004 Hyundai i30 2008-2011

Hyundai Atos Prime 2000-2004 Hyundai i40 2012

Hyundai Atos 2002-2009 Hyundai i45 2011

Hyundai Atoz 2000-2004 Hyundai i800 2002-2009

Hyundai Azera 2006-2012 Hyundai ix20 2011

Hyundai Centennial 2010-2012 Hyundai ix35 2010-2011

Hyundai Elantra Neos 2008-2011 Hyundai ix55 2007-2011

Hyundai Elantra 2001-2012 Inokom Atos 2000-2004

Hyundai Equus 2010-2012 Kia Borrego 2009-2010

Hyundai Genesis 2009-2011 Kia Cadenza 2010-2011

Coupe

Hyundai Genesis 2009-2012 Kia Carens 2003-2010

Hyundai Getz 2003-2011 Kia Carnival 2002-2011

Hyundai Granduer 2006-2012 Kia Cee'd 2006-2010

Hyundai H-1 Bus 2008-2011 Kia Cerato 2003-2010

Hyundai H-1 2002-2009 Kia Forte 2009-2010

Hyundai H-200 2002-2009 Kia K2500 2005-2010

Hyundai HD Coupe 2002-2008 Kia K2700 2005-2010

Hyundai Libero 2002-2009 Kia K3000 2005-2010

Hyundai Matrix 2002-2011 Kia K3000S 2005-2010

3 / 10
HiCOM key teaching manual www.obdtester.com/hicom

Hyundai Santafe 2001-2011 Kia Magentis 2006-2010

Hyundai Santro Xing 2000-2004 Kia Mohave 2009-2010

Hyundai Santro 2000-2004 Kia Opirus 2004-2010

Hyundai Satellite 2002-2009 Kia Optima 2006-2010

Hyundai Solaris 2011 Kia Picanto 2003-2010

Hyundai Sonata 2005-2011 Kia Pregio 2006

Hyundai Starex 2002-2009 Kia Rio 2005-2010

Hyundai Terracan 2001-2006 Kia Sedona 2002-2011

Hyundai Tiburon 2002-2008 Kia Shuma 2001-2004

Hyundai Trajet XG 2000-2007 Kia Sorento 2002-2010

Hyundai Tucson 2005-2011 Kia Soul 2009-2010

Hyundai Tuscani 2002-2008 Kia Spectra 2001-2004

Hyundai Veloster 2011 Kia Sportage 2005-2010

Hyundai Veracruz 2007-2011 Kia Venga 2010

Hyundai Verna 2012 Kia Visto 2000-2004

4 / 10
HiCOM key teaching manual www.obdtester.com/hicom

3. Mechanical keys with RFID chip

– Key coding procedure is available

in control unit IMMO –
Immobilizer from “ECU
Programming/Coding” menu.

Teaching

– Engine must be turned off. Key is

turned to ON position.

– You will be prompted to enter a 6-

digit PIN code. (eg 123456, see page
2 - PIN codes)

– Now you have the key in ignition in

the ON position. This key is coded
after clicking on "Yes" button.

5 / 10
HiCOM key teaching manual www.obdtester.com/hicom

– You will be prompted whether you

want to code another key. If you
click "yes", HiCOM will ask you to
insert the next key. Up to 4 keys can
be coded.(some control units allow
units up to 8 keys). If you click on
"No", the coding process is
terminated and no more keys are
added.

– After successful completion of the

operation, switch off the ignition for
10 seconds.

6 / 10
HiCOM key teaching manual www.obdtester.com/hicom

4. Smartkey
– The feature can be found in Smart Key Code Saving control unit (PIC, SMKCODE)

Teaching

• Engine must be turned off.

• Select "Key Teaching" feature in
"ECU Programming/Coding"
menu.

– You will be prompted to enter a 6-

digit PIN code. (eg 123456, see
page 2 - PIN codes)

– Key fob must be inserted into the

Smart key holder.

– Hold Stop Start Button for 5

seconds

– The same operation will be

performed for other of smart key
fobs. Maximum of 2 Smart keys can
be recoded.

7 / 10
HiCOM key teaching manual www.obdtester.com/hicom

– After coding operation is complete,

HiCOM displays information about
successful coding.

5. Key information

• Shows basic info about keys. Possible

values: Not checked, Learnt, Virgin,
Neutral, Locked

6. Login

• This feature is used to test of PIN

correctness.

8 / 10
HiCOM key teaching manual www.obdtester.com/hicom

7. Password Teaching/Changing

• The password is used to switch the

car into Limp mode.

• You will be prompted to enter

password, if the control unit is not a
"Virgin". The password is numeric,
consisting of 4 decimal digits (eg
1234). Regarding the Virgin control
unit, you are directly prompted to set
a password.

• Now enter a new password. The

password must consist of four-digit
decimal number (eg 1234). After
pressing the "Continue" button the
password is set in the control unit.

8. Neutral Mode
• This function serves to use already used ECU in another vehicle.
• Engine must be turned off. Key is turned to ON position.

9 / 10
HiCOM key teaching manual www.obdtester.com/hicom

9. Limp Home Mode

This function switches the car into emergency mode that is used to drive the car to workshop
in case of all keys are lost or SMARTRA module is not working properly.

The ECM informs the driver about the limp home condition by 5 times blinking for 5 second. Then
the user password can be sent to the ECM by HiCOM. The limp home can be activated also by the
ignition key. The ECM informs the driver by blinking immobilizer lamp about the limp home
condition. Then the input of user password to ECM can be done by special sequence of ignition
on/off.

• Password must be set up first (using "Teaching Password/Changing" feature)

• Engine must be turned off. Key is turned to ON position.

• Type four-digit decimal number (password), eg 1234.

10 / 10