Cat 320C Governor Actuator Calibrate

5/24/2018 PruebasyAjustes320C-slidepdf.
com
Pruebas y Ajustes
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHP
and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2
Número de medio -RENR3814-19 Fecha de publicación -01/01/2011 Fecha de actualización -31/01/2
i01827
Using Service Mode

SMCS - 7569
/sisw eb/sisw eb/ /sisw eb/mediase

Ver imagen
Illustration 1 g00684315
Monitor Panel
(1) Fuel gauge
(2) Engine coolant temperature gauge
(3) Action lamp
(4) Engine speed dial indicator
(5) Hydraulic oil temperature gauge
(6) Message center
Ver imagen
http://slidepdf.com/reader/full/pruebas-y-ajustes-320c 1/47
5/24/2018 PruebasyAjustes320C-slidepdf.com

Monitor Panel
(7) "Up" key
(8) "Left" key
(9) "Right" key
(10) "Down" key
(11) "Cancel" key
(12) "Setting" key
(13) "Menu" key
(14) "OK" key
The information from the controller is displayed on the monitor. The following service programs and function
are available from the controller:
 The controller informs the monitor about the condition of the machine. Some examples are listed:
hydraulic oil temperature, engine coolant temperature and fuel level.
 The controller informs the monitor about any existing and/or past failures of the electronic control
system.
 Various settings of the controller are performed.
 Adjustment and testing of the electronic control system are performed.
Start-Up Of The Service Mode
Ver imagen
Monitor Panel
(7) "Up" key
(8) "Left" key
(9) "Right" key
(10) "Down" key
(11) "Cancel" key
(12) "Setting" key
(13) "Menu" key
(14) "OK" key
The keys of the keypad are used to enter the service mode. The keys are used to change the modes. Next, the
appropriate key is pressed until the desired mode is displayed on the message center.
"Up" key and "Down" key
The "up" key (7) is used and the "down" key (10) is used to scroll up and down through the items in the
message area.
"Left" key and "Right" key
The "left" key (8) is used and the "right" key (9) is used to scroll to the left and to the right through the items
the message area.
"Setting" key
The "setting" key (12) is used to set the menu that is being displayed in the message area.
"Menu" key
The "menu" key (13) is used to access the main menu.
"Cancel" key
The "cancel" key (11) is used to cancel the immediate selection and the key is used to exit the menu screen. T
screen of normal operation will be displayed when the "cancel" key is pressed during the menu screen.
"OK" key
The "OK" key (14) is used to select the item that is being highlighted in the message area.
Start-Up Of The Service Mode
Ver imagen
The above screen should be displayed. Then, press the "menu" key (13).
Ver imagen

The "down" key should be pressed. Highlight the "PREFERENCES" setting. Press the "OK" key.
Ver imagen
The above screen should be displayed.
Ver imagen
Ver imagen

The keys for direction are used to input the password. Input the password and press the "OK" key.
Ver imagen
Typical example of a display
The above screen should be displayed if the correct password is entered.
Ver imagen
The above screen should be displayed if the password that was entered is not correct.
315C Start Mode
Start the service function by using: up key, down key, left key and right key
Exiting The Service Mode

Two methods are capable of terminating the service mode.
1. The service mode will be terminated 10 seconds after the start switch is turned to the OFF position.
Ver imagen
2. Highlight "SERVICE" in the first line of the display.
Ver imagen
3. The "left" key and the "right" key is used to scroll through the display. The display should show "EXI
in the first line.
Ver imagen

4. The service mode will be terminated and the display will return to the above display when the "setting
key is pressed at the "exit" screen.
1 1

/sisw eb/sisw eb/ i01296534

sp_SP /sisweb/sisweb/t /sisweb/sisweb/ /sisweb/mediase

%2Fsisweb%2F %2Fsisweb%2F

Copyright 1993 - 2012 Caterpillar Inc. Tue Feb 21 2012 08:33:12 GMT-0
Todos los derechos reservados.
Red privada para licenciados del SIS.
Desarmado y Armado
320C Excavator 3066 Engine Supplement
i02830
Governor Control Motor - Remove and Install

SMCS - 1716-011; 1716-012
/sisw eb/sisw eb/ /sisw eb/fulltext/f

Removal Procedure
Start By:
A. Remove the counterweight. Refer to Disassembly and Assembly, "Counterweight - Remove".
Ver imagen

1. Remove two bolts (3) and the washers from the hinge.
2. Remove three bolts (1) and the washers in order to remove access panel (2) .
Ver imagen
3. Remove three bolts (5) and the washers in order to remove access panel (4) .
4. Open the engine hood.
Ver imagen

5. Remove two nuts (6) that secure governor linkage (7) to the fuel injection pump.
Ver imagen
6. Loose nut (8) and (9) that secures governor linkage (7) to the engine.
Ver imagen

7. Remove two bolts (10) and the washers in order to remove two clamps (11) that secure the governor
linkage to the chassis.
Note: Some models may only have one clamp (11) .
Ver imagen
8. Disconnect electrical connector (13) .
9. Remove two bolts (14) and the two washers. Remove governor control motor (12) .
Installation Procedure
Ver imagen

1. Position governor control motor (12) on the mounting bracket. Install the two washers and two bolts
(14) .
2. Connect electrical connector (13) .
Ver imagen
3. Install two clamps (11) that secure the governor linkage to the chassis.
Note: Some models may only have one clamp (11) .
4. Install two bolts (10) and the washers that hold clamps (11) in position.
Ver imagen

5. Install governor linkage (7) . Fasten governor linkage (7) with nut (8) and nut (9) .
Ver imagen
6. Install governor linkage (7) to the fuel injection pump. Fasten governor linkage (7) with washers and
two nuts (6) .
Ver imagen

7. Install access panel (4) . Install the washers and three bolts (5) .
Ver imagen
8. Install access panel (2) . Install the washers and three bolts (1) .
9. Install the washers and two bolts (3) to the hinge.
10. Close the engine hood.
11. Check the governor actuator.
ReferenceRefer to Systems Operation/Testing and Adjusting, "Governor Actuator - Calibrate" for

further information.
End By: Install the counterweight. Refer to Disassembly and Assembly, "Counterweight - Install".
1 1 0


sp_SP /sisweb/sisweb/t /sisweb/sisweb/ /sisweb/fulltext/f



Instrucción Especial
Procedure for the Installation of the Cable for the Governor Actuator{1264, 1265, 1716}
Número de medio -REHS2358-02 Fecha de publicación -23/02/2010 Fecha de actualización -23/02/2
i03865
Procedure for the Installation of the Cable for the Governor

Actuator{1264, 1265, 1716}
SMCS - 1264; 1265; 1716

Excavator:
311B (S/N: 8GR1-UP; 9MR1-UP; 2LS1-UP)
311C (S/N: PAD1-UP; CKE1-UP; CLK1-UP)
312B (S/N: 8JR1-UP; 9GR1-UP; 2NS1-UP; 3FS1-UP; 9FS1-UP; 2KW1-UP; 6SW1-UP; 9NW1-
UP)
312C (S/N: CBA1-UP; CAE1-UP; BWH1-UP; BNN1-UP; DBN1-UP; FDS1-UP; CBT1-UP)
313C (S/N: WSA1-UP; HGF1-UP)
314C (S/N: KJA1-UP; PCA1-UP; KHB1-UP; SNY1-UP)
315B (S/N: 5SW1-UP)
317B (S/N: 9WW1-UP; 6DZ1-UP)

318B (S/N: ADC1-UP; AEJ1-UP)
318C (S/N: FAA1-UP; GPA1-UP; BTG1-UP; DAH1-UP; CWP1-UP; MDY1-UP)
319C (S/N: KGL1-UP)
320B (S/N: AED1-UP; BBG1-UP; 3MR1-UP; 4MR1-UP; 4NR1-UP; 5BR1-UP; 6CR1-UP; 9KR1
UP; 1CS1-UP; 4FS1-UP; 5CS1-UP; 6LS1-UP; 8ES1-UP; 9CS1-UP; 9JS1-UP; 4XW1-UP; 5GW1
UP; 2WZ1-UP; 7ZZ1-UP; 8GZ1-UP)
320C (S/N: APA1-UP; BEA1-UP; EGA1-UP; FBA1-UP; GAA1-UP; GHA1-UP; GLA1-UP;
MAA1-UP; PAA1-UP; ANB1-UP; BCB1-UP; BDB1-UP; BGB1-UP; FBB1-UP; GAB1-UP;
MAB1-UP; PAB1-UP; AMC1-UP; BDC1-UP; HBC1-UP; MAC1-UP; PAC1-UP; CCD1-UP;
GAD1-UP; BDE1-UP; NAE1-UP; ALF1-UP; DBG1-UP; EAG1-UP; GNG1-UP; JTG1-UP;
AKH1-UP; SAH1-UP;
UP; SBN1-UP; AXK1-UP;
BER1-UP; BKK1-UP;
BPR1-UP; BBL1-UP;
TBR1-UP; EGL1-UP;
HKT1-UP; JPL1-UP;
RAW1-UP; CLM1-UP;
ALX1-UP; BCN
BRX1-UP;
BMZ1-UP; CLZ1-UP)
320D (S/N: FNA1-UP; DHK1-UP; FXK1-UP; GKL1-UP; CWN1-UP; BWP1-UP; AMR1-UP;
EBT1-UP; CXY1-UP)
321B (S/N: AKG1-UP; 9CZ1-UP)
321C (S/N: KBB1-UP; MCF1-UP; KCR1-UP; DAX1-UP)
323D (S/N: SDC1-UP; CYD1-UP; PBM1-UP; DKW1-UP)
Introduction
This Special Instruction outlines the basic procedures that are required in order to install the cable for the
governor actuator onto an Excavator.
Required Parts
The following parts are required in order to install the cable for the governor actuator onto an Excavator.
Table 1
Required Parts for Replacement of the Cable for the Governor Actuator
Model Item Qty Part Number Description
1 3 4Y-4079 Wire Assembly
2 1 152-9155 Adhesive
All Models
3 1 155-0695 or 185-3998 Thread Lock Compound
4 1 188-8589 Harness
311B
1 309-5864 Motor Repair Kit
312B
315B
317B 1 309-5867 Motor Repair Kit
318B
320B U 1 309-5871 Motor Repair Kit
311C 1 309-5854 Motor Repair Kit

5
313C
314C
320C
320D 1 309-5861 Motor Repair Kit
320C U
323D
All Models 6 1 248-4754 Harness
Disassembling the Governor Actuator
Ver imagen
1. Remove the six screws.
Ver imagen
2. Remove the terminals (A) on the motor.
3. Remove the connector (B) on the potentiometer.
Ver imagen
4. Remove the grommet from the case.
Ver imagen
5. Remove the two screws that connect the motor to the cover.
Ver imagen
6. Remove the four screws that connect the motor to the case for the pulley.
Ver imagen
7. Remove the motor from the case for the pulley.
Ver imagen

8. Remove the pulley (C) from the case for the pulley.
9. Remove the bearings (D) from the pulley, and remove the inner cables (E) from the pulley.
Ver imagen
10. Measure the distance (F) and measure the distance (G). Record the measurements. You will need the
measurements later in order to assemble the governor actuator.
Ver imagen
11. Loosen the locknuts (H) .
12. Rotate the screw caps (J) in order to remove the cables.
Assembling the Governor Actuator
Ver imagen

13. Replace the former cables with the new cables that are included in the new motor repair kit (5) .
14. Insert the inner cables into the case for the pulley.
15. The screw caps (J) should be adjusted to the distances (F) and (G) that were measured in Step 10.
Ver imagen
16. Attach the inner cable of the decelerator cable to the pulley. The decelerator cable does not have blue
tape around the center. Rotate the pulley clockwise for one revolution.
Ver imagen

(K) Groove for the accelerator cable
(L) Groove for the decelerator cable
17. The decelerator cable will sit in groove (L) .
Ver imagen

18. Attach the inner cable of the accelerator cable to the pulley. The accelerator cable has blue tape aroun
the center. Rotate the pulley counterclockwise for one revolution.
19. The accelerator cable will sit in groove (K) .
Ver imagen
20. Paint the inside of the bearings and the outside of the bearings with the Molybdenum coating YM103
that is included in the new motor repair kit (5). Attach the two bearings to the pulley, and insert the
pulley into the case for the pulley.
Ver imagen

21. Install the new packing that is included in the new motor repair kit (5) .
22. Attach the motor to the case for the pulley. Use the screws that were removed in Step 6. Tighten the
screws to a torque of 0.505 ± 0.075 N·m (4.47 ± 0.66 lb in). Refer to Illustration 5.
23. Attach the motor to the cover. Use the screws that were removed in Step 5. Install the new seal washe
that are included in the new motor repair kit (5). Tighten the screws to a torque of 1.00 ± 0.15 N·m (8.
± 1.33 lb in). Refer to Illustration 4.
Adjusting the Governor Actuator
Ver imagen
24. Connect the 248-4754 Harness (6) to the potentiometer.
Ver imagen
25. Connect the terminals (A) for the motor. Attach the 188-8589 Harness (4) .
Ver imagen
26. Connect one 4Y-4079 Wire Assembly (1) from +BAT to the +BAT terminal on the 188-8589 Harnes
(4). Connect one 4Y-4079 Wire Assembly (1) from ground to the ground terminal on the 188-8589
Harness (4) .
Ver imagen
27. Connect a multimeter to the 248-4754 Harness (6) .
Ver imagen
28. Connect one 4Y-4079 Wire Assembly (1) from +BAT to the terminal (M) for the accelerator on the 1
8589 Harness (4). If the voltage on the multimeter is less than 4.13 V, adjust the potentiometer until th
multimeter reads 4.13 ± 0.10 V.
29. Disconnect the wire (1) from the terminal (M) for the accelerator, and connect the wire (1) to the
terminal (N) for the decelerator. If the voltage on the multimeter is greater than 4.13 V, adjust the
potentiometer until the multimeter reads 4.13 ± 0.10 V.
30. Perform Steps 28 and 29 in order to ensure that the voltage on the multimeter reads 4.13 ± 0.10 V.
31. Disconnect the equipment that was installed in Steps 24 through 29.
Ver imagen
32. Adjust the inserted length of the accelerator cable. The length (P) between the outer cable and the
universal joint should be 175 ± 5 mm (6.9 ± 0.2 inch).
33. Tighten the locknut (Q) on the accelerator cable to a torque of 5.05 ± 0.75 N·m (44.7 ± 6.6 lb in), and
apply 155-0695 Thread Lock Compound or 185-3998 Thread Lock Compound (3) to the locknut.
34. Adjust the inserted length of the decelerator cable. The length (R) between the outer cable and the
universal joint should be 200 ± 5 mm (7.9 ± 0.2 inch).
35. Tighten locknut (S) on the decelerator cable to a torque of 5.05 ± 0.75 N·m (44.7 ± 6.6 lb in) and appl
155-0695 Thread Lock Compound or 185-3998 Thread Lock Compound (3) to the locknut.
Completing the Assembly
Ver imagen

36. Install the new packing that is included in the new motor repair kit (5). Apply 152-9155 Adhesive (2)
the packing.
37. Insert the grommet into the case. Apply 152-9155 Adhesive (2) to the grommet. Refer to Illustration 3
38. Connect the terminals (A) for the motor. The two red terminals should be connected, and the two whit
terminals should be connected. Connect the potentiometer with the connector (B). Refer to Illustration
39. Attach the cover to the case. Use the six screws that were removed in Step 1. Tighten the screws to a
torque of 0.505 ± 0.075 N·m (4.47 ± 0.66 lb in). Refer to Illustration 1.
1 1 0




Pruebas y Ajustes
i02149
Troubleshooting Diagnostic Codes
SMCS - 7569

Table 1
Component Identification (CID)
CID No. Name Of Component
91 Throttle position signal

(Not in 321C)
96 Fuel level sensor
110 Engine coolant temperature sensor
167 Alternator
168 Voltage to the power supply (keyswitch)
190 Speed sensor
248
Cat Data Link
( 319C, 320C, 322C, 325C, and 330C ONLY)
254
Electronic Control Module (ECM)
( 312C, 315C, and 321C ONLY)
271
Action Alarm
( 312C, 315C, and 321C ONLY)
286
Engine oil pressure fault
(Not in 321C)
374 Swing brake solenoid
376 Travel alarm
581 Proportional reducing valve for the power shift pressure
586 Engine speed dial
587 Feedback of the governor actuator
588
Communication problem between controller and monitor
( 312C, 315C, and 321C ONLY)
590 Engine controller
598 Automatic travel speed solenoid
600 Hydraulic oil temperature sensor
1161 Pressure sensor for the delivery pump (1)
1162 Pressure sensor for the delivery pump (2)
1525 Straight travel solenoid
2002
Travel alarm
( 319C, 320C, 322C, 325C, and 330C ONLY)
Ver imagen
Example Of A Typical Troubleshooting Procedure
(1) Preparations
(2) Description of the problem
(3) Error code on the display
(4) Items that require checking
(5) Probable cause and solution
Ver imagen

Diagram Of Terminology For The Troubleshooting Procedures
(6) Number of the terminal in the connector
(7) Indication of the short circuit
(8) Number of the connector
(9) "M" Male "F" Female
1. Description (Items that require checking)
2. Measurement of Voltage

o (A) - (B) : 24 V
Voltage is measured at the later terminal. For example, the red test pin + is connected to terminal "A"
and the black test pin - is connected to terminal "B".
3. Meaning of Symbols

a. The following list describes the meaning of specific symbols:
"C-ground" : Ground terminal for the chassis

"P-ground" : Ground terminal for the platform


"R-ground" : Ground terminal for the relay panel


"Cab-ground" : Ground terminal for the cab


4. Preliminary Check

a. Connector
Check the connection of the connector before a troubleshooting procedure is performed. Inspe
the connector for moisture. Moisture in a connector can cause a poor connection. Ensure that t
connectors are mating correctly. Ensure that the pins in the connector are secure.
b. Continuity
Ensure that continuity is present between the following items:
 "C-ground" - "P-ground"
 "C-ground" - "R-ground"
 "P-ground" - "Cab-ground"
Turn the disconnect switch to the OFF position before you perform the continuity checks. The
power is OFF in order to prevent damage to the tester and the circuit.
5. Preparation
a. Turn the key start switch to the OFF position.
b. The hydraulic control lever is in the LOCKED position.
c. Ensure that the controller, the harnesses and the connectors are connected.
Note: Ensure that disconnected wires do not contact the machine in order to avoid damage to
electrical components when power is applied.
Pruebas y Ajustes
i02150
Governor Actuator - Replace

SMCS - 1716-510

Replacement
Note: The 325C, M325C MH, and 330C series do not have a governor actuator.
Ver imagen
Governor actuator for 312C
(1) Governor actuator
(2) Governor cables
(3) Connector for governor actuator
Ver imagen
Governor actuator for 315C
(2) Accelerator cable
Ver imagen
Governor actuator for 319C and 320C series
Ver imagen
Governor Actuator for 321C
(2) Governor Cables
Ver imagen

312C
(2) Accelerator Cables
(4) Support
(5) Bellows
(6) Lever
(7) Decelerator cable
(8) Nut
(9) Nut
(10) Bellows
Ver imagen
319C and 320C series
(4) Support
(5) Bellows
(6) Lever
(8) Nut
(9) Nut
(10) Bellows
Ver imagen
322C Series I
(4) Support
(5) Bellows
(6) Lever
(8) Nut
(9) Nut
(10) Bellows
Ver imagen
321C
(3) Support
(4) Bellows
(5) Lever
(7) Nut
(8) Nut
(9) Bellows
Replacement For Machines Only With Accelerator Cable
1. Install the actuator.
2. Insert the joint of the accelerator cable through the hole in the lever. Install the nut in order to hold the
cable in position.
3. Turn the nut and the locknut of the accelerator cable in the counterclockwise direction until the nuts a
separated.
4. Turn the lever by hand in the counterclockwise direction to the position of high idle.
5. Insert the other threaded portion of the accelerator cable into the notch of the support.
6. Secure the screw cap and the boot so that the screw cap and the boot will not turn. Then turn the nut
until the governor lever touches the high idle stop.
7. Tighten the nut for two turns more.
8. Tighten the locknut (27 ± 3 N·m (20 ± 2 lb ft)) against the support. Ensure that the nut remains in
position while the locknut is tightened against the support.
9. (If applicable) Reinstall the two clamps to the accelerator cable. Do not allow the cable to twist.
Note: Ensure that the governor lever is in contact with the high idle stop. Also, ensure that the nut is
correctly tightened in order to ensure that the accelerator cable has the correct tension. The setting of t
engine speed or an overload condition of the governor actuator could result if the cable is not tightene
correctly.
Note: The minimum allowable bending radius for the cable assembly is 150 mm (6 inch).
Replacement For Machines With Accelerator Cable and Decelerator Cable
1. Repeat step 1 through step 9 in "For Machines Only With Accelerator Cable".
2. Insert the joint of the decelerator cable through the hole in the lever. Install the nut in order to hold the
cable in position.
3. Loosen the nut and the locknut on decelerator cable.
4. Insert the other threaded portion of the accelerator cable into the notch of the support.
5. Tighten the nut until the sag in the bellows is no longer present. Loosen the nut by five turns.
Note: The minimum allowable bending radius for the cable assembly is 150 mm (6 inch).
Adjustment
1. Loosen the nut and the locknut of the accelerator cable. The nuts should be separated as far as possibl
2. Install the accelerator cable and the decelerator cable to the lever.
3. Insert the threaded section of the accelerator cable into the support.
4. Turn the lever clockwise toward the engine until the lever hits the stop for the high idle.
5. Tighten the nut until the sag in the bellows is no longer present. The nut should be tightened two
additional turns.
6. Secure the accelerator cable to the support by tightening the locknut.
7. Insert the threaded section of the decelerator cable into the notch of the support.
8. Tighten the nut until the sag in the bellows is no longer present. Loosen the nut by two turns.
9. Secure the decelerator cable to the support with the locknut. Then, tighten the locknut against the nut.
Ensure that the nut does not turn as the locknut is tightened.
Calibration
Note: For more information, see the topic Testing And Adjusting, "Governor Actuator - Calibrate".
1. Start the engine. Perform the calibration procedure for the governor actuator.
2. After the calibration procedure has been performed correctly, the error log is cleared.
Note: For more information, see Testing And Adjusting, "Logged Error Mode".
1 1 0


sp_SP /sisweb/sisweb/t /sisweb/sisweb/ /sisweb/mediase


Pruebas y Ajustes
i02065
Governor Actuator - Calibrate

SMCS - 1716-524

Note: The 325C, M325C MH, and 330C series does not have a governor actuator.
This function can memorize the rotation angle of the governor actuator and the no-load engine speed. This
information is saved into the controller after the accelerator cable of the governor actuator has been replaced,
installed and/or adjusted. The controller will use the information that was saved in order to determine the targ
position for the actuation of the governor actuator.
Note: Ensure that the calibration procedure for the governor actuator is performed when the governor actuato
the accelerator cable or the controller has been replaced or installed. The temperature of the hydraulic oil shou
be 50 °C (122 °F) prior to the calibration.
Ver imagen
The above illustration is an example of the display for the 312C. All of the other displays are identical with the sales mode
on the fourth line.
1. Enter the service mode.
Ver imagen
2. Highlight the second line of the display and use the direction for direction to scroll through the display
Scroll through the display until the display shows "CALIBRATION".
Ver imagen

3. Highlight the third line by using the keys for direction. The name of the device will be shown on the
third line. Scroll downward until "STANDBY" is highlighted. Press the "OK" key in order to start the
calibration procedure. "GOVERNOR-EXE" is displayed on the third line when the governor actuator
calibrated. Press the "OK" key after confirming the display of "GOVERNOR-EXE".
Ver imagen
4. The above illustration shows a display that is temporarily shown when the governor actuator is moved
the initial position. Press the "OK" key again when the display shows "SP". The calibration procedure
has started.
Ver imagen

5. The numerical number that is being displayed in the fourth line will change during the calibration. Th
number is related to the process of the calibration. See the following table 1.
Table 1
Content For The Process

Display Process
STANDBY Prior to calibration
1 Transfer of the initial position of the governor actuator
SP The initial transfer of the information about the position has been completed.
3 High idle search
4 Positioning of the high idle

5 Data collection of the intermediate points (9-2) down
6 Low idle search
7 Data acquisition of intermediate points (2-9) up
8 Confirmation of the high idle
9 Confirmation of the setting for the speed dial (down)
10 Confirmation of the setting for the speed dial (up)
11 End processing
Ver imagen

6. The above illustration is shown after the governor actuator has completed the calibration.
Warnings
If theafourth
2 for linedescription
detailed of the display shows
of the any of
warning the following warnings a failure is present. See the following tab
displays.
Table 2
Warning Codes
Display Warning Corrective Action
Wire nut is installed too loose

Wire Pitch X (X
by X pitch. X can be a Tighten the accelerator cable by the displayed pitch.
is a number from
positive or negative number. Perform the calibration again.
0 to 9) Turn clockwise.
Wire nut is installed too tight

Wire Pitch X (X
by X pitch. X can be a Loosen the accelerator cable by the displayed pitch.
is number from -9
positive or negative number. Perform the calibration again.
to 0)
Turn clockwise.
High idle is less than the specified value due to

malfunction of the engine, incorrect installation of the
WARNING 01 Insufficient high idle governor cable, poor fuel, etc. After the engine has been
inspected for a malfunction, reinstall the cable and
perform the calibration again.

Incorrect installation of
WARNING 02 Reinstall the cable and perform the calibration again.
cable
Low idle is more than the value specified due to a

malfunction in the engine, an incorrectly installed
WARNING 03 Excessive low idle
governor cable, etc. After the engine has been inspected
reinstall the cable and perform the calibration again.
WARNING 04 Excessive hysteresis Ensure that the cable is adjusted correctly. Reinstall the
cable and perform the calibration again.
High idle is unstable due to a malfunction in the engine

an incorrect installation of the governor cable, etc. Afte
WARNING 05 Unstable high idle
the engine has been inspected, reinstall the cable and
perform the calibration again.
The speed for the dial setting is unstable due to a

WARNING 06 Unstable dial speed malfunction in the engine, an incorrectly installed cable
etc. After the engine has been inspected, reinstall the
cable and perform the calibration again.
Errors
If the fourth line of the display shows any of the following errors a failure is present. See the following table f
a detailed description of the error displays.
Table 3
Error Codes For The Governor Actuator
Error
Description Of The Error Corrective Action
Code
ERROR Improper calibration of another Stop the calibration of the other device. Perform one
01 device calibration at a time.
ERROR Improper calibration of another Stop the calibration of the other device. Perform one
02 module calibration at a time.
ERROR Failure of the interlock signal Perform the troubleshooting procedure that will confirm
03 the signal that communicates with the monitor.
ERROR
Abnormal speed sensor Troubleshoot the confirmation of the speed sensor.
11
ERROR Perform the calibration again. Try to prevent the engine

Engine stop
12 from stopping.
ERROR Reset all operational levers to the neutral position. Perfo

Load available
13 the calibration again.
ERROR Overheating of the coolant or the You need to allow the complete cooldown. Clear the
overheating condition. Perform the calibration procedur
14 hydraulic oil during the calibration
again.
ERROR Pressure decrease in the engine oil Clear the abnormal occurrence and perform the calibrati
15 Check for clogged air cleaner again.
ERROR Excessive governor movement

Troubleshoot the confirmation of the governor actuator.
16 time
Perform the following procedure when the data for the calibration of the governor actuator is cleared.
Ver imagen
1. Highlight the third line by using the arrow keys.
Ver imagen
2. Press the "menu" key. The area that is highlighted will scroll to the right.
Ver imagen

3. Change the display of the third line in order to show "CLEAR" by using the arrow keys. See the abov
illustration.
Ver imagen

4. Highlight the fourth line by using the directional keys. Press the "OK" key when the fourth line is
highlighted.
Ver imagen
5. Press the "OK" key when the display shows "CLEAR?".
Ver imagen
6. The data for the calibration has been cleared when the fourth line of the display shows "CLEARED".
1 1 0




1 1 0


Cat 320C Governor Actuator Calibrate

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cat 320C Governor Actuator Calibrate

Uploaded by

Copyright:

Available Formats

5/24/2018 PruebasyAjustes320C-slidepdf.

Número de medio -RENR3814-19 Fecha de publicación -01/01/2011 Fecha de actualización -31/01/2

Using Service Mode

(1) Fuel gauge

(2) Engine coolant temperature gauge

(3) Action lamp

(4) Engine speed dial indicator

(5) Hydraulic oil temperature gauge

(6) Message center

(7) "Up" key

(8) "Left" key

(9) "Right" key

(10) "Down" key

(11) "Cancel" key

(12) "Setting" key

(13) "Menu" key

(14) "OK" key

Start-Up Of The Service Mode

(7) "Up" key

(8) "Left" key

(9) "Right" key

(10) "Down" key

(11) "Cancel" key

(12) "Setting" key

(13) "Menu" key

(14) "OK" key

"Up" key and "Down" key

"Left" key and "Right" key

The "menu" key (13) is used to access the main menu.

Start-Up Of The Service Mode

The above screen should be displayed.

The above screen should be displayed if the correct password is entered.

Illustration 10 g00687326

315C Start Mode

Exiting The Service Mode

Illustration 11 g00687339

2. Highlight "SERVICE" in the first line of the display.

Illustration 12 g00687350

Número de medio -RENR9406-01 Fecha de publicación -01/12/2011 Fecha de actualización -06/12/2

Governor Control Motor - Remove and Install

4. Open the engine hood.

Note: Some models may only have one clamp (11) .

8. Disconnect electrical connector (13) .

2. Connect electrical connector (13) .

Note: Some models may only have one clamp (11) .

Illustration 10 g00711961

Illustration 12 g00711956

10. Close the engine hood.

11. Check the governor actuator.

ReferenceRefer to Systems Operation/Testing and Adjusting, "Governor Actuator - Calibrate" for

/sisw eb/sisw eb/ i01342127

Número de medio -REHS2358-02 Fecha de publicación -23/02/2010 Fecha de actualización -23/02/2

Procedure for the Installation of the Cable for the Governor

317B (S/N: 9WW1-UP; 6DZ1-UP)

Model Item Qty Part Number Description

1 3 4Y-4079 Wire Assembly

320B 1 309-5869 Motor Repair Kit

320B U 1 309-5871 Motor Repair Kit

321B 1 309-5872 Motor Repair Kit

311C 1 309-5854 Motor Repair Kit

318C 1 309-5859 Motor Repair Kit

321C 1 309-5862 Motor Repair Kit

All Models 6 1 248-4754 Harness

Disassembling the Governor Actuator