Des 6651
Des 6651
Des 6651
carbonated
6651
ETHIOPIAN 4050
STANDARD First edition
2004-xx-xx
Reference number
Price based on 27 pages. DES 6651: 2004
DES 6651
Foreword
This Draft Ethiopian Standard has been prepared under the direction of the Construction Materials Building
and Civil Engineering Technical Committee and published by the Quality and Standards Authority of
Ethiopia (QSAE).
In the preparation of this Draft Ethiopian Standard reference has been made to the following:
- BS 5617:1985, British Standard Specification for Urea-formaldehyde (UF) foam systems suitable for
thermal insulation of cavity walls with masonry or concrete inner and outer leaves, published by the British
Standards Institute (BSI).
Acknowledgement is made for the use of information from the above publication.
The responsible technical committee has reviewed the provisions of the following standards to which
normative reference is made in the text and decided that it is acceptable for use in conjunction with this
standard.
ES 1982, Methods of test for fungal resistance of manufactured building materials made of or containing
materials of organic origin.
ES 4735, Laboratory methods of test for assessment of the horizontal burning characteristics of specimens
no larger than 150 mm × 50 mm × 13 mm (nominal) or cellular plastics and cellular rubber materials when
subjected to a small flame.
ES 5618, Code of practice for thermal insulation of cavity walls (with masonry or concrete inner and outer
leaves) by filling with urea-formaldehyde (UF) foam systems.
ii
DRAFT ETHIOPIAN STANDARD DES 6651
1 Scope
This part of Draft Ethiopian Standard requirements for the properties of the components and the production
parameters, of urea-formaldehyde foam systems suitable for injection into external masonry or concrete cavity walls to
provide improved thermal insulation.
2 Normative references
The following Draft Ethiopian Standards contain provisions which, through reference in this text, constitute the
provisions of this Draft Ethiopian Standard. At the time of publication the editions indicated were valid. All standards
are subject to revision and parties to agreements based on this Draft Ethiopian Standard are encouraged to
investigate the possibility of applying the most recent editions of the Ethiopian Standards indicated below. Registers of
currently valid standards are maintained in the Quality and Standards Authority of Ethiopia.
3 Definitions
For the purposes of this Draft Ethiopian Standard the following definitions apply:
3.1
urea-formaldehyde (UF) foam
an infusible cellular matrix of cured urea-formaldehyde resin insoluble in water and other common solvents
3.2
urea-formaldehyde (UF) foam system
a mixture of urea-formaldehyde resin, hardener, surfactant, water, air and water additives
3.3
foaming hardener
a mixture of surface active agents and acids that enables a foam system to be produced by the introduction of air into
an aqueous solution and will cause UF resin, when mixed into the foam system, to set to an insoluble, infusible matrix
3.4
cavity
an air space between two leaves of an external wall
3.5
effective density (ED)
the mass of a specified sample divided by its initial volume using the method described in Annex A
3.6
declaration
the document supplied by the foam system supplier to the purchaser or to any authorized testing or approvals
organization, containing relevant details for the proper use of the foam system
DES 6651
4 Property requirements
NOTE The quality of the foam system depends on the choice o components (see 4.1) and their method of application as declared
by the foam system supplier (see 4.2).
The UF foam system shall be such that the foam produced, when tested in accordance with the methods given in
Table 1, with samples prepared in accordance with the declaration of the foam system supplier as specified in 4.2,
shall comply with the property requirements also given in Table 1. The samples required or the type tests given in
Table 1 shall be conditioned to constant mass, at 23 ± 2 °C and 63 ± 5 % r.h., after being allowed to dry naturally for a
period of three weeks.
5 Processing requirements
The application of the two foam system components, an aqueous solution of a urea-formaldehyde resin and an
aqueous solution of a foaming hardener shall be as declared by the foam system supplier as specified in 4.2. The
values of the properties given in Table 3 for the system components shall be declared for each foam system by the
system supplier. The components shall then comply with the permissible deviations and limiting values given in Table
3.
2
DES 6651
2 2 Annex C
Water absorption, kg/m max.
NOTE 1 Because UF foam chars on contact with flame and emits little smoke, the presence of foam tends to reduce the
risk of fire and smoke spread via the cavity. However, the use of UF cavity insulation does not affect requirements for
the provision of cavity barriers.
NOTE 2 For design purposes an effective thermal conductivity value for UF foam installed in masonry cavity walls
should be taken to be 0.04 W/(m·K). This aspect is more fully discussed in Annex J of BS 5618:1985.
a CAUTION. The small scale laboratory test described in BS 4735:1974 is solely for assistance in monitoring
consistency of production and is not for use as a means of assessing the potential fire hazard of a material in use.
Linear shrinkage, %3
max. 10 Target value specified by the system ±20 % Annex B
Wet density, kg/ m supplier Annex D
3
DES 6651
Table 3 — Limiting values and permissible deviations for foam system components
Limiting values
Property and permissible Test method
deviations on
declared values
UF resin:
5.2 Declaration
The foam system supplier shall make a declaration for each foam system with respect to the following parameters.
a) The dilution at which the UF resin is to be used and the dilution procedure.
b) The dilution at which the foaming hardener is to be used and the dilution procedure.
c) The ratio to be used of the diluted UF resin to the diluted foaming hardener.
f) The data required in Table 2, the values of the properties given in Table 3 and the usable limits as required in
Table 4.
6.1 UF resin
NOTE The urea-formaldehyde resins of the type used for foam system production have a limited shelf-life. During storage they
undergo changes and will ultimately become unsuitable for use.
The foam system supplier shall ensure that UF resins or use in UF foam systems specified by this standard shall
remain usable for a period of 3 months when stored at temperatures up to 20 °C. The period shall be counted from the
quality control release date and shall be stated for each container.
To ensure that UF foam system quality is not affected by the ageing of the UF resin the foam system supplier shall
define usable limits for the resins in respect of the properties given in Table 4.
4
DES 6651
5
DES 6651
Annex A
A.1 Principle
The effective density is obtained from the sample by relating its dried mass to its original volume.
A cylindrical shaped sample shall be produced in a polyethylene bag which is slightly greater in circumference than
the internal circumference of the tube into which it is placed.
A.3 Apparatus
A.3.1 Rigid tube, approximately 450 mm long and approximately 200 mm internal diameter.
A.3.2 Polyethylene bag, of length approximately 1 000 mm and circumference approximately 10 mm greater than the
internal circumference of the rigid tube.
A.4 Procedure
Place the polyethylene bag inside the tube. Produce the foam sample by injecting through a hole in the bottom of the
bag in order to minimize entrapment of air when filling the bag.
Allow the foam sample to remain within the tube for at least 24 h. After removal from the tube retain the foam in the
polyethylene bag and cut a test specimen as a slice of uniform measured thickness, with its plane normal to the major
axis of the tube and from near the tube centre as shown in Figure 1. The initial thickness of the test specimen shall be
within the range 100 ± 10 mm. Allow the test specimen to dry naturally for a minimum of three weeks with the
polyethylene cover removed.
Determine the mass of the sample using the balance to the nearest 1.0 g.
where
6
DES 6651
F is the final mass of the naturally dried test specimen (in g).
7
DES 6651
Annex B
B.1 Principle
The linear shrinkage is determined by measuring the reduction in circumference of a foam sample after drying for a
specified period.
NOTE It is possible to carry out this test and the test for effective density described in Annex A on the same test specimen.
A cylindrical shaped sample shall be produced in a polyethylene bag which is slightly greater in circumference than
the internal circumference of the tube into which it is placed.
B.3 Apparatus
B.3.1 Rigid tube, approximately 450 mm long and approximately 200 mm internal diameter.
B.3.2 Polyethylene bag, of length approximately 1 000 mm and circumference approximately 10 mm greater than the
internal circumference of the rigid tube.
B.4 Procedure
Place the polyethylene bag inside the tube. Produce the foam sample by injecting through a hole in the bottom of the
bag in order to minimize entrapment of air when filling the bag. Where r is the internal radius of the tube (in mm); L is
the initial thickness of test specimen (in mm); F is the final mass of the naturally dried test specimen (in g).
Allow the foam sample to remain within the tube for at least 24 h. After removal from the tube retain the foam in the
polyethylene bag and cut a test specimen as a slice of uniform measured thickness, with its plane normal to the major
axis of the tube and from near the tube centre as shown in Figure 1. The thickness of the test specimen shall be within
the range 100 ± 10 mm. Allow the test specimen to dry naturally for a minimum of three weeks with the polyethylene
cover removed.
Measure the final circumference of the test specimen to the nearest millimetre.
8
DES 6651
where
9
DES 6651
Annex C
C.1 Principle
The water absorption is determined by floating a test piece of foam on water for 24 h and measuring the mass of
water absorbed.
Two test pieces shall be tested. Each shall have cut surfaces with a base measurement of 100 ± 5 mm by 100 ± 5 mm
and a height of 40 ± 5 mm.
A smooth clean surface is required with minimal damage to the s tructure of the foam surface.
C.3 Apparatus
C.3.2 Water, of known hardness, i.e. between 150 and 250 parts per million by mass calcium carbonate equivalent
content and free of surfactant contamination.
C.4 Procedure
Cut the test pieces to the dimensions specified in C.2. Make accurate measurements of the dimensions to ± 0.5 mm
and record the mass to the nearest 0.05 g.
Float each test piece on the water, the water temperature being maintained at 15 ± 1 °C, the whole test being
conducted in air at a temperature of 23 ± 2 °C. After 24 h, remove the test piece and drain excess water for 30 s by
holding the test piece with one corner of the base pointing downwards. Determine the mass of the test piece plus
absorbed water to an accuracy of 0.05 g.
where
Ma is the mass of the test piece plus absorbed water (in g);
10
DES 6651
C.6 Report
This shall state the water absorption as the average of the values obtained for the two test pieces and the date of the
test.
11
DES 6651
Annex D
The wet density is determined by weighing a container of known volume filled with foam system. The method is
suitable for use on site with a bucket.
D.3 Apparatus
D.3.1 Wide open-topped container of known vo lume preferably wider at the top than at the bottom.
D.3.2 Balance (spring or pan) of sufficient capacity divided into 0.01 kg divisions.
D.4 Procedure
Determine the mass of the empty container (M1). Fill the container (see note) with foam system, keeping the foam
system injection nozzle below the foam system surface to minimize the production of entrained air pockets, and level
off the foam system top using a straight-edged stick or knife. Determine the mass of the filled container to the nearest
0.01 kg (m 2).
NOTE The use of a thin plastics liner makes it much easier to keep the measuring container clean. Care should be taken to avoid
trapping air between the liner and the container.
where
12
DES 6651
Annex E
The gel time is the time elapsing from making the sample until the foam system is no longer fluid, i.e. it readily parts
when a palette knife is drawn across it.
E.2 Apparatus
E.2.2 Flat palette knife, with blade 150 mm to 200 mm long and 24 mm to 40 mm wide.
E.2.3 Clean board at least 750 mm square, or, alternatively, a polyethylene sheet.
E.3 Procedure
Set up the foam system generating equipment to produce a foam system, in accordance with the method of
application declared by the foam system supplier as specified in 4.2. Take a sample for determination of gel time by
forming a pile of foam system approximately 400 mm in diameter, then drawing the nozzle away from the pile to
produce a ridge approximately 300 mm in length, 100 mm wide and 75 mm high (see Figure 2).
Start the stop watch as soon as the formation of the ridge has been prepared [see Figure 2(1)]. Start testing the gel
time at the point on the ridge most remote from the conical pile by inserting a palette knife to two-thirds of the depth of
the foam system and drawing it across the ridge in a direction normal to the principal axis of the ridge. Before the gel
time has been reached the cut will not cause splitting of the foam system and it will retain its creamy consistency [see
Figure 2(2)].
Continue testing in this manner, inserting the palette knife into the foam system to make tests approximately 25 mm
apart whilst progressing towards the conical pile. Record the time as the gel time when the foam system readily parts
as the palette knife is drawn across it [see Figure 2(3)].
Report as the gel time of the foam system, the time elapsing between the start of the preparation of the ridge and the
time when parting occurs.
13
DES 6651
14
DES 6651
Annex F
F.1 Principle
The absence of oil carry-over from the compressor is checked by the administration of a sharp shock to the foam
system which will precipitate its collapse if significant quantities of oil are present.
F.3 Procedure
Approximately 1 min after the foam system has gelled, determined by the method described in Annex E, drop the
container on to some hard ground from a height of approximately 100 mm.
F.4 Report
Report whether the level of foam system has significantly decreased.
15
DES 6651
Annex G
G.1 Principle
The appearance of the cell structure obtained in the foam system is determined by visual examination.
G.3 Procedure
After the foam system has gelled, split the initial 400 mm diameter pile of foam system down the middle on the test
board. Examine the section.
G.4 Report
Report whether the foam system has a fine, uniform, cellular structure with no pockets of collapsed foam system and
with no evidence of formation of layers in the foam system structure.
16
DES 6651
Annex H
NOTE The procedure described may be used with either powdered or liquid resins. This test is very sensitive to the oven
characteristics.
H.1 Principle
The percent age loss in mass of the resin is determined after the resin has been heated under specified conditions.
H.3 Apparatus
H.3.1 Ventilated oven, capable of being maintained at a temperature of 120 ± 2 °C throughout the working space.
H.3.2 Flat bottomed dish, 70 mm to 90 mm in diameter and maximum depth of 100 mm.
H.4 Procedure
Dry the dish for at least 30 min in the oven at a temperature of 120 °C. Cool in the desiccator and weigh to the nearest
milligram.
Put into the dish 2 ± 0.2 g of resin, spreading the contents as evenly as possible over the bottom of the dish. Record
the mass of the dish and contents to the nearest 0.001 g.
Place the dish and contents in the oven on a level perforated sheet metal shelf and maintain at a temperature of 120 ±
2 °C for a period of 3 h.
Remove the dish and contents from the oven and allow to cool in the desiccator. Remove the dish and contents from
the desiccator and redetermine the mass immediately.
where
17
DES 6651
18
DES 6651
Annex J
J.1 Principle
The determination of free formaldehyde in the UF resin is based on the reaction between sodium sulphite and
formaldehyde and is carried out at a reduced temperature to prevent decomposition of the resin by the sulphite.
J.2 Reagents
J.2.2 Thymolphthalein indicator 1 % (m/m) in 50 : 50 V/V 64 O.P. industrial methylated spirits: distilled water solution.
J.3 Apparatus
J.3.4 Burette
J.4 Procedure
From the weighing bottle weigh accurately 6 ± 0.1 g of the resin into the stoppered conical flask.
Add 15 mL of deionized water and three to four drops of the thymolphthalein solution. Shake the mixture vigorously
until the complete solution of the resin is obtained. Neutralize the solution with 0.1 mol/L sodium hydroxide or 0.05
mol/L sulphuric acid as required. Cool the solution to + 0.5 °C. Add 25 mL of the sodium sulphite solution, previously
cooled to a temperature of 0.5 °C. If free formaldehyde is present, a brilliant blue colour appears. Run in rapidly from
the burette the 0.5 mol/L sulphuric acid until the colour disappears. Check the end point by adding one or two extra
drops of the indicator solution and note if this addition causes any colouration. When no further colouration is
observed the end point has been reached.
19
DES 6651
where
20
DES 6651
Annex K
K.1 Principle
Water tolerance is determined by progressively diluting the resin solution to determine the dilution at which
precipitation of the resin occurs.
NOTE The water tolerance is a measure of the degree to which the resin can be diluted. The correct water tolerance is an
important factor in ensuring good foam formation.
K.3 Apparatus
K.3.10 Timer, 1 h.
K.4 Procedure
Add 6.5 ± 0.1 g, equivalent to approximately 5 mL, of resin to each of the test tubes and place in a rack in the water
bath. First, add 5 mL of water from the burette, drop by drop, to each of the tubes, shaking well. In the same manner
add to individual tubes appropriate quantities of water (see note) as shown in Table 5, selected on the basis of
experience or a preliminary test. Shake continuously to ensure good mixing. Retain the tubes in the bath for 1 h before
inspecting them.
21
DES 6651
NOTE It is very important not to over -dilute inadvertently at any time. Not more than 1 mL of water should be added at a time, and it
should be added very slowly at the start when the resin is most viscous.
Bring the temperature of the water bath containing resin sample and tap water for dilution to 25 ± 0.5 °C. Measure 50
mL of the resin into the beaker and add 50 mL of tap water from the burette (see note to K.4.1) with constant stirring.
Return some of the diluted resin back to the 50 mL cylinder, insert the stopper and shake for a few seconds. Pour the
fluid back into the beaker.
Repeat the operation twice to ensure that all the resin in the cylinder is transferred to the beaker. Pipette 10 mL of the
solution into each of the test tubes and add to individual tubes from the burette appropriate quantities of water as
shown in Table 5, selected on the basis of experience or a preliminary test, and shaking continuously to ensure good
mixing. Retain the tubes in the water bath for 1 h before inspecting them.
Note the maximum quantity of water which does not result in a clear demarcation and calculate the percentage water tolerance WT
from the equation:
K.6 Report
Report the percentage water tolerance WT.
22
DES 6651
Annex L
L.1 Principle
The acid content (expressed as the % phosphoric acid) is determined by titration with standard alkali.
L.2 Reagents
L.2.2 Phosphate indicator solution. Mix 2 parts of solution (A) with 1 part of solution (B).
solution (A): 0.1 % m/m phenolphthalein in 50 : 50 V/ V 64 O.P. industrial methylated spirits: distilled water;
solution (B): 0.1 % m/m naphthol-phthalein in 50 : 50 V/ V 64 O.P. indus trial methylated spirits: distilled water.
L.3 Apparatus
L.4 Procedure
Weigh approximately 3 g to 4 g accurately of hardener into the 250 mL conical flask. Dilute with approximately 50 mL
of distilled or deionized water. Add 3 to 4 drops of indicator solution and titrate with 1.0 mol/L sodium hydroxide
solution to a violet end point.
where
23
DES 6651
L.6 Report
Report the total acidity A (expressed as % phosphoric acid).
24
DES 6651
Annex M
M.1 Principle
The break time of the resin is determined by measuring the time taken for it to flow through the orifice of a standard
flow cup, before the stream breaks into droplets.
M.3 Apparatus
M.3.7 Thermometer
M.4 Procedure
Immerse the resin sample, enclosed in a screw-topped bottle, and the test cup in the water bath for 2 h or until the
resin sample has reached a temperature of 25 ± 0.5 °C. Dry the cup, plug it, clamp it into the stand, and place the
beaker beneath the cup. Pour the resin sample into the cup until it runs into the overflow.
Unplug the orifice so that the resin sample flows into the beaker, and simultaneously start the stop watch. Stop the
watch when the first drip of resin appears, i.e. when the flow becomes discontinuous.
M.5 Report
Report the time recorded to the nearest second as the average of three results.
NOTE As the flow of these resins may be non-New tonian, it is unsound to convert the break time to absolute units of viscosity.
25